Single check valve assembly with a brushed nickel coated DZR brass body, incorporating a screwdriver operated isolation valve and EPDM ‘O’ rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass or chrome plated DZR brass (CP02-8511 suffix models) body with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass body with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies with DZR brass bodies, incorporating two spring loaded, resilient trim in-line check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-verifiable double check valve assembly incorporating DZR brass (chrome plated) body two spring loaded, resilient trim in-line check valve cartridges & a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of non verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. The products incorporate a drain port between the cartridges. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies (brushed chrome plated) with a drain port located between the cartridges either at the top or bottom. Models incorporate an isolation valve with either lever or butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body, compression models are nickle plated. A drain port is provided between the cartridges. Compression models are to be used with copper pipe to EN1057. Maximum working pressure 16.0 Bar. Maximum operating temperature for the D220W range 85°C. Maximum operating temperature of the D200CW range 60°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body, compression models are nickle plated. A drain port is provided between the cartridges. Compression models are to be used with copper pipe to EN1057. Maximum working pressure 16.0 Bar. Maximum operating temperature for the Hattersley Fig 250W range 85°C. Maximum operating temperature of the Hattersley Fig 250CW is 60°C
Tundish with a black metal body and a straight through pattern. The tundish complies with the requirements of an air gap to drain. Maximum operating temperature 99°C.
Tundish which incorporates a black or white plastic body and complies with the requirements of air gap to drain. Incorporates a spring loaded diaphragm on the outlet. Maximum operating temperature 100°C.
Range of tundishes with plastic body which comply with the requirements of an air break to drain. The outlet incorporates a spring loaded diaphragm Maximum operating temperature 85°C.
Commercial pasta cooker. Flow is controlled by a solenoid valve and discharges via a stainless-steel spout outlet Maximum working pressure 3.0 bar. Cold water supply only.
Range of open or closed top, circular, sectional, cold water storage cisterns with corrugated & galvanised steel bodies and an EPDM liner.
Range of three hole, deck mounted, single outlet (fixed) combination bidet tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlet incorporates a plastic aerator. Product is supplied with pop up waste & metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a pull out spray with push button trigger assembly and dome type operating member. The pull out spray also incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). The outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly with a brass body (various finished and styles), incorporating a quarter turn ceramic disc headwork with cross top operating members. The spout outlet incorporates a plastic aerator and the product is supplied with a pop-up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Deck mounted drinking fountain tap having a stainless steel body with an integeral shroud over the outlet. Outlet incorporates a stainless steel cover and strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate either a plastic flow straightener or aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (chromium plated) brass bodies, incorporating quarter turn ceramic disc headworks or ceramic cartridge headworks (see models) with single lever operating members. The swivel spout of the TMO35SSCM model is (chromium plated) stainless steel. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). The spout outlet of ‘Arc’ models incorporates a plastic flow straightener. All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 100°C. Hot-water circuit has a maximum operating temperature of 65°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The products are supplied with metal backnuts and the spout outlets incorporate a plastic aerator or a plastic flow straightener (supplied with both). Maximum working pressure 5.0 Bar Maximum operating temperature 60°C.
Two hole, single outlet (fixed), combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating ceramic disc headworks with single lever operating members and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener or optional aerator. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of five hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating a ceramic cartridge headwork controlling the flow to the shower handset and two quarter turn ceramic disc headworks controlling the flow to the spout outlet, all with single lever operating members. The spout outlets incorporate a plastic aerator. The inlet to the shower handsets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A range of combined bath filler and overflow with a plastic body (various trim sets). The outlet incorporates a plastic flow regulator and the products are supplied with a click waste. Maximum operating temperature 65°C.
Ranges of combined bath filler and overflow waste assembly incorporating a cable operated pop-up waste. Maximum operating temperature 65°C.
‘HydroDOS’ chlorine dioxide dosing system with PVC-u pipework and EPDM ‘O’-rings. The product incorporates a water meter, strainer, isolation valves and a drain cock with hose spigot. Maximum working pressure 6.0 bar. Cold water use only.
Range of cylindrical expansion vessels incorporating butyl rubber diaphragms. The products are supplied with an Airfix TD T piece. Maximum working pressure of model Airfix D 35 litre is 8.0 bar. All other models have a maximum working pressure of 10.0 bar. Maximum operating temperature 100°C.
Talbot range of self tapping ferrule straps with plastic bodies and a nitrile rubber seal. The product incorporates either a ¾” BSP (M) connection or a 25mm or 32mm push fit connection on the outlet from the cutting arm. For below ground use only. Maximum working pressure 16.0 bar. Cold water use only.
Range of LK press fittings with brass bodies and stainless steel sleeves for use with LK Universal PEX pipe. Jointing is achieved by hydraulic compression. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of Aquaterra PP-RCT socket fusion fittings for use with Aquaterra PP-RCT SDR 6 pipe and Aquaterra PP-RCT SDR 7.4 pipe (manufactured to EN ISO 15874). Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
‘Epsilon Series’ polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Aquaflow polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Range of WC dual flush drop valves with an ABS body and silicon seal. The valves are operated via a push button assembly for either full or reduced flush and incorporate an internal adjustable height overflow. Cold water use only.
Dual flush WC drop valve with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only
Dual flush WC drop valve with an internal overflow. The valve is operated via a lever operated assembly for either full or reduced flush. Cold water use only.
Range of WC dual flush outlet valves with silicon seals and ABS bodies. The SKY005, SKY015 & SKY020 valves are operated via a push button assembly for either full or reduced flush. The SKY030 model may be operated via a push button assembly or a lever for either full or reduced flush. The valves incorporate an internal overflow. For cold water use only.
WC dual flush drop valve with plastic body silicone and rubber seal. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold Water Use Only.
WC dual flush drop valve comprising of a plastic body and silicone seating washer. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water only.
Range of commercial glass washing machines with flow controlled via a solenoid valve. The products are supplied with a dual layer supply hose (Grey PVC outer/Black PVC inner) with ¾” captive nuts at either end and a loose double check valve assembly (suitable for backflow protection against Fluid Category 3) for installation prior to the inlet hose. Maximum working pressure 4.0 Bar. Cold water use only.
Range of indirect heat interface units with copper brazed stainless-steel heat exchangers, providing heating and instantaneous hot water. The products incorporate an expansion vessel on the cold-water supply to the plate heat exchanger and a safety relief valve on the space heating circuit set @ 3.0 bar. The domestic hot water and space heating circuit are both fitted with drain valves incorporating cover caps. Maximum working pressures: Domestic hot water 10.0 bar. Space Heating 2.5 bar. District Heating 3.0 bar. Maximum operating temperature 85˚C.
Electronically controlled heat interface units (HIU) with twin stainless-steel plate heat exchangers providing space heating and instantaneous hot water. The cold inlet supply to the plate heat exchanger incorporates an isolation valve and a water hammer arrestor. The space heating circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product is supplied with a filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (suitable for backflow protection against fluid category 3) which incorporates an isolation valve. The cold mains inlet and the domestic hot water outlet each incorporate a brass bodied spherical valve with a butterfly handle. Maximum working pressures and operating temperatures: Primary: 16.0 bar and 90˚C. Domestic hot water (DHW): 10 bar and 65˚C. Secondary (space heating): 2.5 bar and 85˚C.
Range of RINNAI continuous flow water heaters with stainless steel plate heat exchangers providing heating and instantaneous hot water .The hot water is generated via a plate heat exchanger. Also supplied is a drain valve and a flow sensing device. Maximum working pressure - 10 bar Maximum working pressure - 85˚C
Electronically controlled heat interface units (HIU) with twin stainless-steel plate heat exchangers providing space heating and instantaneous hot water. The cold inlet supply to the plate heat exchanger incorporates an isolation valve and a water hammer arrestor. The space heating circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product is supplied with a filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (suitable for backflow protection against fluid category 3) which incorporates an isolation valve. The cold mains inlet and the domestic hot water outlet each incorporate a brass bodied spherical valve with a butterfly handle. Maximum working pressures and operating temperatures: Primary: 16.0 bar and 90˚C. Domestic hot water (DHW): 10 bar and 65˚C. Secondary (space heating): 2.5 bar and 85˚C.
Range of ‘HYCO’ electric instantaneous water heaters with plastic bodies, NBR and silicone ‘O’-rings. The inlet of model IN96T incorporates a plastic strainer. Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
‘Hydraulic Block 2’ range of integrated water circuits for use with combination boilers comprising of a plastic body, stainless steel thermistors and a plate heat exchanger. The primary circuit incorporates a pump assembly. Maximum working pressures: Primary Circuit 2.5 bar. Secondary Circuit 10.0 bar. Maximum operating temperatures: Primary circuit 85˚C. Secondary circuit 65°C. Cold supply only.
Hydroblock unit consisting of a stainless steel heat exchanger, a pressure relief valve pre-set at 3.0 bar, diverter valve and return valve. Maximum working pressure 2.5 bar. Maximum operating temperature 90°C
Digital water meter with brass body incorporating a plastic strainer on the inlet and a non-return valve (not suitable for backflow protection) on the outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Water meter incorporating a brass inner body, a plastic outer body and liquid silicone ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Air break to drain, incorporating brass bodies with a grey epoxy powder coating. Maximum operating temperature 60°C.
Hygienic flush box providing a timed flush facility. The supply is via a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection, flow sensor, spherical ball valve and strainer. The products incorporate a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The units have multiple interface user functions for timed flush, wireless technology and data storage. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of flow through valves with brass bodies and EPDM ‘O’-rings, incorporating a spherical valve and a separate drain tap. The products are intended for connection prior to an expansion vessel. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of concealed bathroom boxes with extractable shower hoses. The inlet attached to the concealed box incorporates an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the shower hose also includes a stainless steel strainer. Maximum operating temperature 60°C.
VDROO range of stainless steel multistage centrifugal pumps with stainless steel impellers, diffusers and outer sleeves. The pumps incorporate a Silicone Carbide and EPDM mechanical seal. Maximum working pressure 25.0 bar DIN flange. Maximum working pressure 16.0 bar for oval flange. Cold water use only.
Range of cold water supply booster sets, incorporating a stainless steel manifold system and between 1 and 4 pumps depending on model. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels. Maximum working pressure 10.0 bar or 16.0 bar, dictated by the pump model(s) fitted. Cold water use only.
CM(E)(C) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. (CMEC models were added October 2023). The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Cast iron models: Maximum working pressure 10.0 bar. Cold water use only. Stainless steel models: Maximum working pressure 16.0 bar. Maximum operating temperature 60°C for self-priming models, 99°C for all other models.
Dutypoint ‘VS’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels.. Maximum working pressure 10.0 bar. Cold water use only.
Range of black plastic bodied multistage, self or manually primed, high pressure centrifugal pumps with a stainless steel outer casing, plastic impellors, EPDM seals and ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.
‘DUSO’ timed-flow control shower column with black plastic spray plate. The product is operated by a hydraulically actuated push paddle control. Maximum working pressure 5.0 bar. Maximum operating temperature 50°C.
Range of over head shower outlets with stainless steel bodies (various finishes). Inlets incorporate silicone washer with stainless-steel strainer. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of wall or ceiling mounted overhead shower outlets (chromium plated brass) and shower arm. Maximum operating temperature 60°C.
Range of wall mounted handshower, hose and elbow sets with metal bodies (various finishes), incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Handsets incorporate an approved check valve cartridge , however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C
Range of atmospheric steaming ovens having a 25 litre, 70 litres or two 25 litres capacity chambers. The water supply is controlled via a solenoid valve and incorporates a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar & maximum operating temperature 23°C.
Range of in-line ‘Y’-patterned strainers with flanged cast iron bodies (blue epoxy powder coated) and stainless steel mesh strainers. The strainers also incorporate a drain plug. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
43250-TASTR Range of in-line `Y` pattern strainers incorporating DZR brass bodies, stainless steel mesh strainers and white PTFE gaskets. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Flow through valve (chromium plated brass) incorporating EPDM ‘O’-rings, PTFE seals, a drain valve, isolation valve and water mixing feature for connection to expansion vessels. Maximum working pressure 10.0 bar. Cold water use only.
Test Point incorporating a brass body and EPDM ‘O’-ring and seals. Maximum working pressure 20.0 bar. Maximum operating temperature 99°C.
Drain off valve with a DZR brass body. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Drain off valve with brass body (chrome plated) and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of drain off taps incorporating DZR brass bodies, non-rising spindle operating mechanism and EPDM ‘O’-rings and seat washer. D340 range incorporates a lockshield mechanism and the D341 range incorporates a key operated mechanism. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain off taps incorporating DZR brass bodies, non-rising spindle operating mechanism and EPDM ‘O’-rings and seat washer. FIG 371 range incorporates a lockshield mechanism and the FIG 370 range incorporates a key operated mechanism. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Drain cock elbow incorporating a DZR brass body with EPDM ’O’-rings (ZELB250445 model) or NBR ‘O’-rings (ZELB250446 model added July 2022). Both models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: ZELB250445 model - 10.0 Bar. ZELB250446 - 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps (brass, chrome plated brass or DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. Spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic flow straighteners and the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless steel braided, white (translucent) polyethylene lined (CPWX models) or white elastomeric thermoplastic (TPSiV) lined (SPWX models) flexible hose assemblies. Hoses are available with a variety of end connections (see model), either brass or nickel plated brass (SPWX/CPWX10 models). Maximum working pressures 10.0 bar. Maximum operating temperature 90°C.
Fabdec ‘Excelsior’ ranges of direct, indirect, solar direct and solar indirect stainless steel insulated unvented hot water storage cylinders with internal expansion. The DHW circuit consists of a temperature and pressure relief valve set at 7.0 bar 95°C, an inlet manifold consisting of an in-line pressure reducing valve adjustable between 2.7 & 3.3 bar (but factory set @ 3.0 bar), an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a pre-set expansion relief valve set at 6.0 bar and a strainer. The product is supplied with a tundish. Maximum supply pressure to pressure reducing valve is 10.0 bar. Maximum working pressure Primary circuit 6.0 bar. Maximum working pressure Secondary circuit 5.5 bar. Maximum operating temperature 85˚C.
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. The storage cylinders incorporate an internal air bubble to accommodate the expansion of hot water. The DHW circuit has a factory fitted temperature and pressure relief valve set at 10.0@90˚C. The inlet control group includes a pressure reducing valve set at 3.0 bar, single check valve cartridge (verified by test and suitable for backflow protection against Fluid Category 2) and a expansion valve set at 8.0 bar. The products are supplied with a tundish and a motorised valve to be installed on the primary indirect circuit. Maximum supply pressure to the pressure reducing valve is 12.0 bar. Maximum working pressure of primary circuit is 6.0 bar. Maximum secondary circuit is 9.5 bar. Maximum operating temperature 85°C.
Advance Appliance ranges of direct, indirect, solar direct and solar indirect stainless steel insulated unvented hot water storage cylinders with internal expansion. The DHW circuit consists of a temperature and pressure relief valve set at 7.0 bar 95°C, an inlet manifold consisting of an in-line pressure reducing valve adjustable between 2.7 & 3.3 bar (but factory set @ 3.0 bar), an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), a pre-set expansion relief valve set at 6.0 bar and a strainer. The product is supplied with a tundish. Maximum supply pressure to pressure reducing valve is 10.0 bar. Maximum working pressure Primary circuit 6.0 bar. Maximum working pressure Secondary circuit 5.5 bar. Maximum operating temperature 85˚C.
Range of 2, 3 and 4 port manifold assemblies with either DRZ brass or brushed chrome plated brass bodies incorporating screw down isolation valves with dome type operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of air venting valves with a gunmetal body PTFE seats and fluoroelastomer ‘O’-rings. Maximum working pressure 13.5 bar. Maximum operating temperature 95°C.
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
Range of concealed flow controls (brass body with various different finishes) incorporating two, quarter turn ceramic disc headworks with single lever operating members controlling the flow to an external outlet (not supplied). Model BK2 is a flow control with adjustable bracket and collection box. Model BK2A is a flow control with bracket. Model BK2B is a flow control. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted concealed manual blending valves with a DZR brass body incorporating a ceramic cartridge headwork with a single lever operating member, fitting is available with trim set (available in various finishes). Maximum working pressure 10.0 bar. Maximum working temperature 70°C.
Range of T-type thermostatic mixing valves with DZR brushed chrome brass bodies and a thermostatic cartridge controlling the temperature. Models TM200VP-3/4ZC and TM200VP-3/4ZD incorporate isolation valves and stainless steel strainers on the inlets. All models incorporate check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Combined pressure and temperature relief valves with DZR brass bodies, stainless steel springs, silicone diaphragm and PTFE washers. The valves incorporate lever easing gear. The valves are factory pre-set at 6.0 bar (PTEM510001), 7.0 bar (PTEM510002) or 10.0 bar (PTEM510003). Maximum operating temperature 95°C.
Combined pressure and temperature relief valves with DZR brass bodies, stainless steel springs, nylon coated probe, EPDM diaphragm and silicone seat disc. The valves incorporate lever easing gear. The valves have a factory pre-set pressure of 7.0 or 10.0 bar (see model). Maximum operating temperature 85°C.
Combined pressure and temperature relief valves with DZR brass bodies, stainless steel springs, nylon coated probe, EPDM diaphragm and silicone seat disc. The valves incorporate lever easing gear. The valves have a factory pre-set pressure of 7.0 or 10.0 bar (see model). Maximum operating temperature 85°C.
Range of high and low pressure diaphragm float operated valves with brass body & brass drop arm lever. The valves discharge from an up and over arrangement. Maximum working pressure 14.0 bar (model 1FVB004) or 3.0 bar (model FVB104). For cold water use only.
Flow control valve with a cylindrical brass body, stainless steel spring and thermostatic element. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
‘GNVP’ range of non-return valves with a black or white plastic housing, (white added October 2024). The product incorporates two test/drainage plugs. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of spring loaded, resilient trim, non-return valves (blue epoxy coated cast iron body), with bronze bushing, stainlesss steel spring and disc, and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, resilient trim, non-return valves (blue epoxy coated cast iron body), with bronze bushing, stainlesss steel spring and disc, and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of combined thermal balancing and pressure reducing valves with gun metal bodies, stainless-steel strainer, pressure gauge and temperature gauge. Maximum inlet supply pressure 16.0 bar. Outlet pressure range of 1.5 bar – 5.5 bar. Maximum operating temperature 85°C.
Range of pre-set pressure relief valves incorporating DZR brass bodies and an EPDM diaphragm, (for pre-set pressures see model). The valve is fitted with hand operated rotating easing gear. Maximum working pressure is the same as the pre-set pressure (see model). Maximum operating temperature 85°C.
Range of latching solenoid valves with brass bodies, incorporating stainless steel strainer with EPDM O rings and diaphragms Maximum working pressure 12.0 Bar or 16.0 Bar on (SCPH262C020 & SCPXH262C020BW TPL 21896 Only). Maximum operating temperature 85.0°C
Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and an integrated flow meter sensor. Both the inlet and the outlet incorporate a white plastic flow restrictor. The products are also supplied with an optional EPDM outlet gasket, for installation over the outlet spigot. Maximum working pressure 10.0 bar (to diaphragm). Maximum operating temperature 85°C.
Range of lever or screw driver operated in-line spherical valves (chromium plated brass body), brass ball and EPDM sealing ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Aangled spherical valve (screwdriver operated) with DZR brass bodies, PTFE seats and NBR seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Screwdriver operated spherical valves with DZR brass bodies, PTFE seats and NBR seals. The fittings incorporate two approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of lever operated spherical valves incorporating brass bodies, brass or stainless-steel balls, PTFE seats and EPDM ‘O’ rings. Pressfit connections are for use with copper pipe. Maximum working pressure 16.0 bar. Maximum operating temperature 85.0°C
Screwdriver operated angled servicing valve with brass body, brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of in-line isolation valves with a nickel plated brass (11-1046 (1046) range) or DZR brass body (all other models), chromium plated DZR brass ball (1601 (¼ ” to 2”), 2045 (¼” to 2”) & 1046 ranges), SS304 ball (1601 (¾” to 2”) & 2045 (¼” to 2”) ranges) or chromium plated brass ball, and PTFE seats. The products are supplied with either a single lever (1601, 2045 & 1046 range), single lever with extension stem kit, (1601 & 2045 range), single lever with lockable handle (1601 & 2045 range), butterfly operating members (1601 & 2045 range), T-handle, short black lever (1601 & 2045 range) or screwdriver operated (1046 range). The 11-1015 (2045) range and 11-1046(1046) range is for use with copper pipe manufactured to EN1057. Maximum working pressure 40.0 bar (1601 range), 25.0 bar (2045 & 1046 range). Maximum operating temperature 85°C.
Angled spherical valve with brass body, brass ball (chrome plated), and screwdriver operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of inline screwdriver or lever operated servicing valves with nickel plated brass bodies, nickel plated ball, EPDM ‘O’-rings and PTFE Seats. The S0232BH-1 and S0232BH-2 models also incorporate a (metal) lever. The S0280L-1 and S0280L-2 models are full bore insolation valves. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating brass bodies and balls (chrome plated), EPDM ‘O’-rings and PTFE gaskets. Products are supplied with either red or blue butteryfly operating member or screw driver operated. Maximum working pressure 50.0 bar. Maximum operating temperature 100°C.
Range of spherical valves incorporating chrome plated brass bodies and balls, and PTFE seats. The products are supplied with either butteryfly or lever handles. Maximum working pressures - see model. Maximum operating temperature 100°C.
Range of plastic bodied inline, tee and angled spherical valves with EPDM ‘O’-rings and either lever or screwdriver operated (see model). For use with copper and PE-x pipe (manufactured to BS7291-3). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Flomasta Range of plastic bodied inline, tee and angled spherical valves with EPDM ‘O’-rings and either lever or screwdriver operated (see model). For use with copper and PE-x pipe (manufactured to BS7291-3). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 bar. (Cold water use only).
Range of screw down drain valves having brass bodies and EPDM ‘O’-rings, for use with EN1057 copper tube R250 half hard. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screw down stop valve (chromium plated brass) incorporating a dome (triangular) type operating member with a NBR rubber washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85.0°C
Range of front loading commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The machines are supplied with double check valve assemblies. Maximum working pressure 10 Bar Maximum operating temperature 60°C
Commercial clothes washing machine having a flexible inlet hose and solenoid valve with filter at the inlet supplying a Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Front loading, commercial washing machine. Flow is supplied via solenoid valves and the unit incorporates a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of commercial conveyor type dishwashers with the flow controlled by a solenoid valve and discharged via three type AB air gaps (pre-wash, rinse and wash) (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a brass bodied ‘Y’-pattern strainer, brass adaptors ¾”x¾” (M)x(M) and (F)x(F) and dual layer PVC inlet hoes(s) (grey outer/black inner) and EPDM washers. The DR*11**** model has two solenoids and requires three inlet hoses and also includes a brass tee-piece to connect them ¾”x¾”x¾” (M). Maximum working pressure 6.0 bar. Maximum operating temperature 60ºC.
Range of water conditioners incorporating Ball valves. TurboMAG models Simplex, Duplex Skid, Duplex Wall and Quadplex Skid incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Range of ultraviolet disinfection units incorporating isolation valves and draw off tapes. Maximum working pressure 16.0 bar. Maximum operating temperature 50ºC.
Range of ultra-violet disinfection units consisting of a stainless-steel body and quartz tubes with EPDM O rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50.0°C
Range of under-counter or counter-top drinking water dispensers delivering still ambient, still chilled & sparkling water. HygienePlus®. Models incorporate a built-in filter system. The flow is controlled by a solenoid valve which is either operated by a touch or a touch pad. The water is dispensed via a tap arrangement on under-counter versions or an integrated outlet on counter-top versions. The inlets incorporate an approved check valve cartridge assembly however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Cold water use only.
Range of undercounter or deck mounted drinking water fountains which dispense ambient and/or chilled water. Flow is controlled via a solenoid valve and the products are activated via a push button or infa-red sensor . Maximum working pressure 7.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. Maximum working pressure 10.0 bar. Cold water use only.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
'RS-0004'. White coloured, compression moulded seal ring manufactured from 'ADR 96' ceramic material. For use with water up to 85°C.
'HPL 2510 PW'. Factory applied, two-component epoxy coating comprising of a base and hardener. Mix base and hardener in a weight ratio of 2.78:1. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied coating system, black coloured, consisting of two component primer and three component polyurethane top coat. Mix primer in a ratio 2:1 by weight (component A:B), apply and cure for 2 hours at 23°C, then mix topcoat in a ratio 100:5.6:2.4 by weight (component A:B:C) before applying and curing for 20 seconds at 23°C. This approval covers the following manufacturing sites: France and China. For use with water up to 23°C.
'Krystaline 1'. Grey coloured, site applied cement based coating, intended to be used to waterproof concrete. Mix coating with water in a volume ratio of 5:2. Apply to pre-wetted cement and allow to cure for 1 hour@5°C. Pre-wet the cement before applying a second coat and then dry cure for 2 hours@5°C before wet curing for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydropriv PE100 Pipe'. Black coloured (with blue external stripes), extruded PE100 pipe. In January 2024, blue coloured, extruded PE100 'Hydropriv PE100 Pipe' was added to the approval. Both pipes are for use with water up to 23°C.
'Reno 100'. Black coloured (with blue external stripes), extruded polyethylene pipe. For use with water up to 23°C.
'Reno 100+'. Dual layered, extruded polyethylene pipe comprising of a black coloured inner and blue coloured outer layer. For use with water up to 23°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'Aquaterra Faser Composite Stabil Pipe PP-R (SDR 6 & SDR 7.4)'. Extruded, multi-layered PP-R pipes comprising of a green coloured inner layer, red coloured middle layer and green coloured outer layer. For use with water up to 85°C.
‘BOR Plus Faser Composite Stabil Pipe PP-R (SDR 6 & SDR 7.4)’. Extruded, multi-layered PP-R pipes comprising of a beige coloured inner layer, green coloured middle layer and beige coloured outer layer. For use with water up to 85°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AD’ air gap arrangement (suitable for backflow prevention against Fluid Category 5). The inlet incorporates a strainer and flow regulator (not verified by the test facility) and is pumped from an internal water storage cistern via a heating unit to various outlet nozzle arrangements. Maximum working pressure 10 bar. Cold water supply only.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AD’ air gap arrangement (suitable for backflow prevention against Fluid Category 5). The inlet incorporates a strainer and flow regulator (not verified by the test facility) and is pumped from an internal water storage cistern via a heating unit to various outlet nozzle arrangements. Maximum working pressure 10 bar. Cold water supply only.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator and is pumped from an internal water storage cistern via a heating unit to various outlet nozzle arrangements. Maximum working pressure 10.0 bar. Cold water supply only.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). . The inlet incorporates a strainer and flow regulator (not verified by the test facility) and is pumped form an internal water storage cistern via a heating unit to various outlet nozzle arrangements. Maximum working pressure 10.0 bar. Cold water supply only.
Range of wall hung WC pans with bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The unit has a heated seat and dryer function. Cold supply only Maximum working pressure 10.0 bar.
BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve (Phantom T & Phantom V) or dual flush syphon (Phantom S) for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by a manual push button. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush Syphon of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a lever. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve discharging via a type AG airgap and a dual or single flush pneumatic or dual flush cable operated drop valve capable of full flush volumes of up to 6 litres with a reduced flush of up to 4 litres. The cistern is operated by manual push button/push plate. The side entry inlet valve is mounted internally and is supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush Syphon of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a lever. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a bottom entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a pnuematic push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC cistern in white plastic incorporating a BS 1212-4:2016 side entry float operated inlet valve providing a Type AG air gap arrangement and a single or dual flush outlet valve. The full flush can be set at 6 litres and the reduced flush can be set at 3 litres. The inlet supply incorporates a servicing valve. Maximum operating pressure 10.0 bar. Cold water use only.
Range of concealed WC cistern in white plastic incorporating a BS 1212-4:2016 side entry float operated inlet valve providing a Type AG air gap arrangement and a single or dual flush outlet valve. The full flush can be set at 6 litres and the reduced flush can be set at 3 litres. The inlet supply incorporates a servicing valve. Maximum operating pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern is operated by manual push button. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) concealed WC cistern incorporating a side entry compact type float operated inlet valve discharging via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) and a dual or single flush pneumatic or dual flush cable operated drop valve capable of full flush volumes of up to 6 litres with a reduced flush of up to 4 litres. The cistern is operated by manual push button/push plate. One of the side entry inlet valves is mounted internally and is supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap and lever operated syphon capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 997:2018 Roca Wall Hung W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern. The cistern incorporates a side entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by a manual push button / push plate options. The inlet valve is mounted internally and supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 997:2018 Vitra wall hung W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern. The cistern incorporates a side entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 3 litres. The cistern can be operated by manual a push button / push plate options. The inlet valve is mounted internally and supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve Maximum working pressure 10.0 bar. Cold water use only.
BS EN 997:2018 Vitra wall hung W.C. pan (Ceramic), Thomas Dudley ‘A’ or Illusion Compact Universal frame incorporating a Thomas Dudley Vantage Concealed cistern. The cistern incorporates a side entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 3 litres. The cistern can be operated by manual a push button / push plate options. The inlet valve is mounted internally and supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 997:2018 RAK Compact Rimless Wall Hung 700mm COMRIMWH W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern with a side entry compact type float operated inlet valve which discharges via a Type AG airgap and a dual flush pneumatic drop valve capable of full flush volumes of 4.5 litres and a reduced flush of 3 litres. The inlet connection hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Standpipe assembly break tank with a Type ‘AB’ air gap (verified by test – suitable for backflow protection against fluid category 5) mounted to the top of the standpipe body. The tank is filled via a compact float valve and has two screened weir slots. Water is then supplied by gravity from the break tank to the hose outlet below. Flow is activated via a spherical valve located behind a lockable panel. In addition to the isolation valve, the product incorporates a single check valve assembly (suitable for backflow protection against Fluid Category 2) prior to the spherical valve and an in-line ‘Y’ pattern strainer after it. The spherical valve includes a drain plug to allow for draining. Insulation is provided up to the drain point. Maximum working pressure 10.0 bar. Cold water use only.
Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass body with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with a drain port located between the cartridges. For use with copper pipe manufactured to BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Calomax Eclipse’ range of electrically heated counter top or wall mounted catering water boilers. The boilers incorporate a stainless steel cold water feed cistern which has a combined vent/overflow fitted with an insect screen. The water to the cistern is supplied via a solenoid valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The water level is electronically controlled via level sensors. The water is dispensed via a manually operated brass bodied (chrome plated)/stainless steel bodied self-closing tap(s) or a push button controlling a solenoid valve prior to the outlet. The counter top models are supplied with a PVC coated flexible inlet hose (¾” BSP (F) x 15mm standpipe) and a push fit adaptor (15mm push fit x ¾ BSP (F)). Maximum working pressure 10.0 bar (to the solenoid valve). Maximum temperature of dispsensed water 90°C for PB3C10 & PB3W5 models and 97°C for all other models. Cold water supply only.
Single hole, single outlet deck mounted (fixed) combination tap assembly with soap dispenser and hand dryer appliances operated via an infra-red sensor. This product incorporates a solenoid valve and plastic flow restrictor. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Single hole, single outlet wall mounted (fixed) combination tap assembly with soap dispenser and hand dryer appliances operated via an infra-red sensor. This product incorporates a solenoid valve and plastic flow restrictor. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener. The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (chrome plated) brass bodies. Incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a aerator. Inlets incorporate single check valve cartridge (however the the complete assembly has not been tested to demonstrate it provides adequate backflow protection)Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly with brass body (chrome plated), incorporating single sequential headwork with single lever operating member. The inlets incorporate a screwdriver operated servicing valve and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, two-hole, single outlet (fixed) concealed combination tap assembly with brass body (chrome plated), incorporating a single sequential headwork with single lever operating member. The inlets incorporate a screwdriver operated servicing valve and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members. interconnecting flexible hoses. The spout outlets incorporate a self-cancelling diverter to shower outlet and a plastic flow straightener with stainless steel mesh. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with various operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic aerators. The products are supplied with a shower hose and metal back nuts. The hose connector incorporates an approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of basin spout outlets with brass bodies (various finishes), the outlet incorporates either a metal aerators, plastic aerators or open outlet (depending on model). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
ERA-01 range of SDR11 and SDR17 polyethylene butt welded fittings for use with ERA-02 range of SDR11 and SDR17 PE 100 pipe. SDR11 rated pipe and fittings have a maximum working pressure of 16.0 bar. SDR17 rated pipe and fittings have a maximum working pressure of 10.0 bar. For above and below ground use. Cold water use only.
Range of compression fittings incorporating polypropylene bodies, plastic pipe liners, plastic grip rings and EPDM seals. For use with both PE80 & PE100 pipe manufactured to BS EN 12201. For above and below ground use. Maximum working pressure 12.5 bar (PE80 pipe 20mm - 63mm). Maximum working pressure 16.0 bar (PE100 pipe 20mm - 63mm). Maximum working pressure 10.0 bar (PE100 pipe 75mm - 110mm). Cold water use only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of WC dual flush drop valve comprising of a plastic body, silicone seating washer and an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of WC dual flush drop valves comprising of a plastic body, silicone seal and an internal overflow. The valve is operated via a push button or lever assembly for either full or reduced flush. Cold water use only.
WC cable operated dual flush drop valves with ABS bodies and silicone seals. The valves incorporate an internal overflow and are operated via a push button assembly for either full or reduced flush. Cold water use only.
Single flush pneumatically operated drop valve with a rubber seating washer and ABS body. The valve is operated by a separate push button assembly.
Range of urinal flushing mechanisms with a solenoid valve controlling the flow. The valves are controlled via an infra-red sensor. The inlet incorporates a stainless steel strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Electronically controlled heat interface units (HIU) with twin stainless-steel plate heat exchangers providing space heating and instantaneous hot water. The cold inlet supply to the plate heat exchanger incorporates an isolation valve and a water hammer arrestor. The space heating circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product is supplied with a filling loop assembly consisting of an elbow shaped copper pipe, isolation valve and double check valve assembly (suitable for backflow protection against fluid category 3) which incorporates an isolation valve. The cold mains inlet and the domestic hot water outlet each incorporate a brass bodied spherical valve with a butterfly handle. Maximum working pressures and operating temperatures: Primary: 16.0 bar and 90˚C. Domestic hot water (DHW): 10 bar and 65˚C. Secondary (space heating): 2.5 bar and 85˚C.
Copper heat transformer. Maximum working pressure 11.0 bar. Maximum operating temperature 95°C.
Range of domestic hot water units incorporating instantaneous or semi-instantaneous plate heat exchanger assemblies. The product incorporates a motorised control valve, managed primary and secondary pumps (see model), and a drain valve on both circuits. Maximum working pressures: 10.0 bar primary, 9.5 bar secondary. Maximum operating temperatures: 110°C primary, 85°C secondary.
Range of outdoor air to water heat exchanger units incorporating a pump, drain valve and isolation valve. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C
Range of stainless-steel plate heat exchangers with EPDM gaskets. The primary circuit, (excluding the E2 prefix models), incorporates a drain valve and a pump (excluding STP prefix models including an ‘N’ as the 14th figure). Operating parameters: Maximum working pressure of the secondary circuit: 6.0 bar or 10.0 bar (see model). Maximum working pressure of the primary circuit: E4 models: 6.0 bar. C3, E3, E2, i2: 10.0 bar. Models added February 2023 – Econoplate STP3, STC3, STP2, STC2 & STP4: 10.0 bar. Maximum operating temperature: Primary 140°C & Secondary 85°C.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressure relief valve set at 3.0 bar. The supplies to both primary hot water and secondary are controlled via spherical valves. The boilers incorporate a filling loop assembly which incorporates a double check valve assembly (suitable for backflow protection against Fluid Category 3). Primary circuit: Maximum working pressure 2.5 bar. Maximum operating temperature 82°C. Secondary circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of gas fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The cold inlet incorporates an angled spherical valve with a brass body, chromium plated brass ball and a lever operating member. The primary circuit incorporates an expansion vessel, isolation valves on flow and return, drain valve and a pressure relief valve set at 3.0 bar. Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature for the secondary circuit is 55˚C. Cold supply only.
Greenstar Heatslave II range of floor standing oil-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, which incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The cold water inlet incorporates a screwdriver operated spherical valve followed by a plastic flow regulator inserted within the pipework. Maximum working pressure: Primary circuit 2.5 bar. Secondary circuit 10.0 bar. Maximum operating temperature 82°C.
Hydraulic block assembly comprising a flow sensor, primary pump assembly, pressure relief valve preset at 3.0 bar and plate heat exchanger. Maximum working pressures: secondary = 10.0 bar and primary = 2.5 bar. Maximum operating temperature 80°C.
MJ (Multi jet) range of water meters with either ductile iron (MJF model) or brass (MJ models) blue epoxy coated bodies and EPDM rubber ‘O’-rings. Maximum working pressure16.0 bar. Maximum operating temperature 85°C.
Range of ‘Resident Valves’ with a DZR brass body consisting of water meter manifold, an isolation valve on the inlet, a pressure reducing valve (adjustable between 1.5 and 6.0 bar) and 2 non-return valves which are located on the outlet of the water meter manifold. The ‘Plus’ models are also supplied with an isolation valve on the outlet, which incorporates a drain tap. Maximum supply pressure 16.0 Bar. Cold water above ground use only.
Range of meter boxes incorporating a plastic manifold arrangement consisting of a stop valve with non-rising spindle , check valve (however the complete assembly has not been tested to demonstrate it provides adequate backflow) and concentric meter port. Some models incorporate a drain off or blacking plug. Connections can be compression or push fit (see model). For use with PE8-0 pipe to BS EN 12201 and copper to EN 1057. Maximum working pressure 16.0 bar. Cold water use only.
Screw down pattern, angled solation valve with a dome type operating member, DZR brass body and an EPDM gasket and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of hand wash and dryer units The flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a non-verifiable double check valve assembly (suitable for backflow protection against Fluid category 3) for installation on the inlet. The double check valve assembly also incorporates a drain port, (located in between the cartridges), and an integral spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 50ºC.
Range of flow and temperature sensors with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of pushfit hose connectors with either plastic (white or black) or chrome plated brass bodies and EPDM ‘O’-rings. SHCV prefix models incorporate screwdriver operated servicing valves. All pushfit connections are for use with PEX pipe (manufactured to BS7291-3) and copper pipe (manufactured to EN1057). Barbed end connections are not approved for use with any hose. Chrome plated brass body models are also for use with PB pipe (manufactured to BS7291-2). Maximum working pressure 10.0 bar (servicing valve models only). Barbed end connections are open outlet use only. Cold water use only.
Range of pump inverters with plastic bodies, NBR rubber and EPDM rubber seals and ‘O’-rings. The products incorporate an inline resilient trim non-return valve. Maximum working pressure 13.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel (AISI 304) bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Maximum operating temperature 90°C.
Range of magnetic drive volumetric rotary vane pumps with a plastic housing and built-in relief valve. Maximum working pressure: 22 series models - 20.0 bar, 20 series models - 14.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum operating pressure 11.0 bar. Maximum working temperature 90°C.
Range of pump units with plastic bodies and impellers, EPDM ‘O’-rings, expansion vessel with an EPDM membrane and a carbon graphite/ceramic/NBR shaft seal (bt-ar 13 bx 4ff xp). Each pump inlet incorporates a non-return valve. Single versions are standalone pumps, twin versions also include stainless steel manifolds. Maximum working pressure 10.0 bar. Cold water use only.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: EH Three phase models 85°C, EH Single phase models 55.0°C and EHsp models 35°C.
Range of self-priming pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of cast iron (blue epoxy coated) (G versions only) or stainless steel (all other versions - F, N, R, T) vertical multistage pumps with stainless steel impellers, shaft and outer sleeve and EPDM 'O'-rings and seals. The pumps incorporate a ceramic/carbon graphite/EPDM and stainless steel mechanical shaft seal (QBEGG). Maximum working pressures: 1-22SV models: 1SV27-1SV37 (F VERSION) - PN16 (25mm). 3SV23-3SV33 (F VERSION) - PN16 (25mm). 5SV23-5SV33 (F VERSION) - PN16 (32mm). 10SV27-10SV21 (F VERSION) - PN16 (40mm). 15SV11-15SV17 (F VERSION) - PN16 (50mm). 22SV12-22SV17 (F VERSION) - PN16 (50mm). 1SV02-1SV25 (F VERSION) - PN25 (25mm). 3SV02-3SV21 (F VERSION) - PN25 (25mm). 5SV02-5SV16 (F VERSION) - PN25 (32mm). 10SV01-10SV13 (F VERSION) - PN25 (40mm). 15SV01-15SV10 (F VERSION) - PN25 (50mm). 22SV01-22SV10 (F VERSION) - PN25 (50mm). N VERSIONS ALL MODELS - PN25 (25-50mm). R VERSION ALL MODELS - PN25 (25-50mm). T VERSION ALL MODELS - PN16 (25-50mm). 33-125SV models: 33SV1-33SV5, 33SV6/2AG150T/D & 33SV6/2AN150T/D (G or N VERSION) - PN16 (65mm). 46SV1-46SV5 (G or N VERSION) - PN16 (80mm). 66SV1-66SV5 (G or N VERSION) - PN16 (100mm). 92SV1-92SV4 (G or N VERSION) - PN16 (100mm). 125SV1-125SV6 (G VERSION) - PN16 (125mm). 33SV7-33SV10, 33SV6/1AG150T/D, 33SV6/1AN150T/D, 33SV6G150T/D & 33SV6N150T/D (G VERSION) - PN25, (N VERSION) - PN16 (65mm). 46SV6-46SV9 (G VERSION) - PN25, (N VERSION) - PN16 (80mm). 66SV6-66SV8 (G VERSION) - PN25, (N VERSION) - PN16 (100mm). 92SV5-92SV7 (G VERSION) - PN25, (N VERSION) - PN16 (100mm). 125SV7-125SV8 (G VERSION) - PN25 (125mm). 33SV10-33SV13 (G VERSION) - PN40 (65mm). 46SV10-46SV13 (G VERSION) - PN40 (80mm). Cold water use only. VERSION) - PN25 (100mm). 92SV5-92SV7 (G or N VERSION) - PN25 (100mm). 125SV7-125SV8 (G or N VERSION) - PN25 (125mm). 33SV10-33SV13 (G VERSION) - PN40 (65mm). 46SV10-46SV13 (G VERSION) - PN40 (80mm). Cold water use only.
Range of booster pumps with stainless steel bodies and impellers (AISI 304: AL-RED models or AISI 316: CP models), EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure: CP(m) 100-130-132-150-158 and AL-RED(m) 600-610-620 models: 6.0 bar. All other models: 8.0 bar. Maximum operating temperature 90°C.
‘e-SH’ range of centrifugal booster pumps with a blue polymer coated stainless steel body, stainless steel impeller and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Cold water use only.
Range of cold water in tank booster sets incorporating an ‘AG’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.
Range of cold water in tank booster sets incorporating an ‘AB’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.
‘EVE Whole house’ twin impeller booster pump with a plastic body and impellers and EPDM ‘O’-rings. The inlet and outlet hoses incorporate a screwdriver operated isolation valve. The pump body outlets incorporate a non-return valve. The product is supplied with two loose combined EPDM and stainless steel inlet washers and two loose EPDM outlet washers. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of shower handsets with chrome plated bodies and built in flow restrictors. Maximum operating temperature 60°C.
Range of wall mounted or ceiling mounted shower arms with brass bodies (various finishes) Maximum operating temperature 90°C.
Range of wall mounted shower kits, incorporating a shower handset, shower hose and wall elbow connection. Maximum operating temperature 60°C.
Range of shower columns with chromium plated brass bodies. Maximum operating temperature 60°C.
Range of shower handsets with brass bodies available in various styles and finishes. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
VKF series of flow alarm switches with a plastic body. Maximum working pressure 12.0 bar. Maximum operating temperature 100°C
Range of flow switches with plastic bodies. The VKX15M prefix models are supplied with an inline brass adaptor. The VKX05M prefix models are supplied with a brass adaptor for direct insertion into a pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of flow switches with plastic bodies. The VK308/10/15/20/25/32/40/50M and VKS08/10/15/20/25/32/40/50M prefix models are supplied with an inline brass adaptor. The VK305/306/309M and VKS05/06/09M prefix models are supplied with a brass adaptor for direct insertion into a pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of flow switches incorporating brass or stainless steel bodies. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of flow sensors with brass or plastic bodies. Flow sensor type series VTY10 (plastic body, G3/4): Maximum working pressure 10.0 bar. Maximum operating temperature 85°C. Flow sensor type series VTY10 (plastic body, Quickfasten OD 22.5mm): Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. Flow sensor type series VTY10 (brass body, G1/2): Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of bib taps incorporating brass bodies. The S0311BL-1 and S0311BL-2 models incorporate an approved single check valve cartridge on the inlet and the outlet (hose union), however, the complete product has not been fully tested to demonstrate it provides backflow protection. The S0311BL-1 and S0311BL-2 models also incorporate a drain port. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bib taps incorporating brass bodies. The BTHUCV1/2 and BTHUCV3/4 models incorporate an approved single check valve cartridge on the inlet and the outlet (hose union), however, the complete product has not been fully tested to demonstrate it provides backflow protection. The BTHUCV1/2 and BTHUCV3/4 models also incorporate a drain port. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The DIEN-BT&DCV1/2” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Self-closing tap for drinking water fountains (chromium plated brass) with dome type operating member. The spout outlet incorporates a stainless-steel strainer. The product is supplied with a metal back nut. Maximum working pressure 5.0 bar. Cold water use only.
Range of self-closing taps (chromium plated brass) incorporating spring loaded headworks with dome type operating members. The spout outlet of the 9000 model incorporates a plastic flow straightener. The products are supplied with a metal back nut. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C, except for the 9054SA model which is cold water use only.
Self-closing drinking fountain tap (chromium plated brass) with non-concussive headwork operated via a push button. The tap incorporates a metal shroud and is supplied with a metal back nut. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic flow straightener. During January and February 2022, the products are supplied with metal back nuts. From March 2022, the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
PEX lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel and brass double interlocked PEX lined flexible hose assemblies (various finishes - see model) incorporating EPDM washers. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
EPDM lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of indirect and direct unvented storage cylinders consisting of either no coil (GLE) or a factory fitted single (GLC) or twin coil (GLT). The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@85˚C for 1.0-6.0 bar products and 10.5 bar@95°C for 6.0-10.0 bar products. The products are supplied with an inlet control group (safety kit) consisting of a pressure reducing valve, an expansion relief valve 6.0 bar (1.0-6.0 bar products) or 10.5 bar (6.0-10.0 bar products) and an approved check valve, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is also supplied with an expansion vessel. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
A range of wall mounted self-closing shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. Model TF222CP250 is supplied with metal back nut. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Thermostatic blending valve (chromium plated brass), the valve body inlets incorporate single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with stainless steel strainers and inlet connections that incorporate screw driver operated spherical valves. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of T-Type thermostatic mixing valves incoporating a brass body and a thermostatic cartridge controlling the temperature. The 15mm & 22mm compression models are for use with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves (lever or handwheel operation) with a cast iron body (blue epoxy coated), EPDM seat and stainless steel disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies. Adjsutable between 1.0 bar and 5.5 bar outlet pressure. Compression models are for use with copper pipe to EN1057. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 80°C.
‘Europress’ range of in-line pressure reducing valves, with DZR brass bodies and EPDM ‘O’-rings and washer. The outlet pressure is adjustable between 1.0 - 5.5 bar. Operating parameters: 2430012 EUROPRESS model: Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C. 2430034 EUROPRESS & 2430100 EUROPRESS models: Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 99°C.
In-line adjustable pressure reducing valve assembly with a DZR brass body. The assembly also incorporates a stainless strainer (part of the pressure reducing valve), a spherical valve with a brass ball on the inlet, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) on the outlet, and a drain port with a brass plug. The product also includes a port with a plastic plug to accommodate a gauge/sensor (not supplied). Adjustable outlet pressure range between 1.0 and 6.0 bar. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with DZR brass bodies. The capillary union and compression models are for use with copper pipe (manufactured to BSEN 1057). The inlets incorporate a stainless strainer. Maximum supply pressure 21.0-25.0 bar - outlet adjustment range: 2.5 bar min. outlet pressure, 6.0 bar maximum outlet pressure. Maximum supply pressure 16.0-20.0 bar - outlet adjustment range: 2.0 bar min. outlet pressure, 6.0 bar maximum outlet pressure. Maximum supply pressure 11.0-15.0 bar - outlet adjustment range: 1.5 bar min. outlet pressure, 6.0 bar maximum outlet pressure. During January 2022 these products were for cold water use only. Between February 2022 and January 2027 the products are for use with water up to 65°C.
‘Easiset 320 series’ adjustable (in-line) pressure reducing valves with DZR brass bodies. Compression and pushfit models are for use with copper pipe (manufactured to BS EN 1057:2006+A1:2010). From March 2022 the pushfit models can also be used with PB pipe (manufactured to BS EN 7291-2:2010) and PEX pipe (manufactured to BS EN 7291-3:2010). Maximum inlet supply pressure: 16.0 bar all models with copper pipe. From March 2022: SBPRED320001 & SBPRED320005 models: 12.0 bar with PEX & PB pipe. SBPRED320050 & SBPRED320055 models: 6.0 bar with PEX & PB pipe. Maximum outlet pressure 1.5 bar to 5.5 bar. Maximum operating temperature: COLD WATER EASISET 320 SERIES: 45°C with copper pipe, and from March 2022: cold water use only with PEX & PB pipe. HOT WATER EASISET 320 SERIES: 80°C with copper pipe, and from March 2022: 80°C with PEX & PB pipe.
Range of pilot operated pressure reducing control valves with ductile iron bodies (blue polyester or epoxy coating) and EPDM diaphragm. Maximum inlet pressure 25.0 bar. Outlet pressure setting is adjustable in the range of 1.0 – 16.0 bar. Maximum operating temperature 65°C.
Range of pre-set, spring loaded, angled pressure relief valves, with a plastic body and EPDM diaphragm. The B312021 CST model only is pre-set at 4.0 bar, all other models are pre-set at 3.0 bar. The valves are fitted with either rotary type easing gear or hand operated lifting gear. Maximum operating temperature 99°C.
Range of angled isolation valves with brass bodies (brushed chrome plated), for use with copper tube manufactured to EN1057. The inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spherical valves with bronze bodies, DZR brass ball (sizes ½” to 1”) and bronze ball (sizes 1 ¼” to 2”) PTFE seats and various operating member types (see models). Maximum working pressure: 25.0 bar. Maximum operating temperature: 85⁰C.
Flow through valve with a brass body and EPDM ‘O’-rings, incorporating a spherical valve and a separate drain port/plug. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of in-line, “T” type or angled spherical valves incorporating brass bodies and brass ball, EPDM ‘O’-rings/Washers, PTFE seats and single lever or butterfly lever operating members. Some models incorporate port or pressure gauge. Models 0516/03DCVR1, 0516/03DCVR2 & 0516/04TR1 incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressures 10.0 bar Maximum operating temperature 100°C.
Range of brass bodied, straight and angled two and three-port spherical valves. Some models incorporate a screw-down pattern drain valve. Products incorporate a chrome-plated brass ball and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating stainless steel strainers, chrome plated brass ball, housed within DZR brass bodies with a brushed chrome finish. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of screwdriver operated servicing valves incorporating brass bodies and chromium plated brass ball, nylon seats and EPDM seals. Maximum working pressure 7.0 bar. Maximum operating temperature 99°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves with a DZR brass body and disc, and PTFE washers. The products are operated by a non-rising spindle headwork with a hand wheel operating member. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of cold water inlet control groups with DZR brass bodies, consisting of a pressure reducing valve, (all models are adjustable between 1.0 and 6.0 bar, but some come pre-set from the factory - see model), a pressure relief valve (set at 6.0 or 8.0 bar - see model) and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The pressure relief valve is fitted with a rotary type easing gear. All products for use with copper pipe manufactured to BS EN 1057. Maximum inlet supply pressure 20.0 bar. Cold water use only.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of thermostatic circulation valves incorporating brass bodies and EDPM ‘O’-rings. Some models incorporate a gauge port. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
‘Tornado’ & ‘Ninjo’ ranges of freestanding and undercounter bedpan washers with flow controlled via a solenoid and discharged via type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 8.0 bar. Maximum operating temperature 60°C
Range of commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with three ¾” x ¾” BSP (F) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet prior to a HDPE inlet hose with ¾” x ¾” captive nut end connections. Maximum working pressure 5.7 Bar. Maximum operating temperature 60°C.
Range of commercial front loading, hood type & utensil washer type dishwashing machines with flow controlled by solenoid and discharged via type AB air gap (verified by test - suitable for backflow protection against fluid category 5) . The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of water conditioners. The WFL38 model has a brass body, all other models are stainless steel. Operating parameters: GRANDER® Inline units - Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. GRANDER® Flexible unit - Maximum working pressure 6.0 bar. Maximum operating temperature 75°C. GRANDER® Apartment unit & Immersion units - Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
`Hy-MAG` range of electromagnetic water conditioners with blue PTFE coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
'Droople DRP-M90-IMP'. White coloured, injection moulded acetal cogwheel. For use with water up to 65°C.
‘Hostaform® C9021 ECO-B NATURAL, C9021, M15HP, C2521, C13021, C13031, C27021 ECO-B NATURAL, C27021, C52021 & M90JG’. Injection moulded, natural (which appear to be white) acetal materials available in the following colours: Black 14 DW (formerly known as Black 14), White 22, Grey 33, Grey 36, Grey 39, Red 46, Red 47, Yellow 56, Brown 65, Green 76, Blue 87, RAL 2010, RAL 4008 & RAL 5005. Customer specific colours may also be provided with a nomenclature following the structure ‘xx/yyyy DW’ where ‘yyyy’ denotes the specific colour shade, ‘DW’ denotes ‘Drinking Water’ & ‘xx’ denotes 10 – black, 20 - white (incl. Cream, 30 – grey, 40 – red (incl. Pink), 50 – yellow, 60 – brown (incl. Beige), 70 – Green & 80 – blue. For use with water up to 65°C.
'Rapox Brown 4 Washer'. Brown coloured, dry pressed ceramic washer. For use with water up to 85°C.
'SYAL B950' (brown coloured) & 'SYAL A950' (white coloured). Dry press moulded ceramic materials. For use with water up to 85°C.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Promag'. Factory applied, black coloured (once mixed), polyurethane primer and topcoat manufactured in Suzhou, China. Mix components A & B of the primer in a 1:2 mass ratio and apply as per manufacturer's instructions dated '13-01-2022' Cure for 2 hours@23°C. Mix components A, B & C of the topcoat in a 92.59%:5.19%:2.22% volume ratio and apply as per manufacturer's instructions dated '13-01-2022'. Cure for 20 seconds@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Orgal® Hydroflex 10'. White coloured, acrylic polymer emulsion cement modifier, which is a liquid additive intended to be mixed with cement to achieve a coating. Mix cement:additive:water in a 197.5:30:10 mass ratio and apply as per manufacturer's instructions '2/18'. Cure for 28 days@23°C and @50% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Crystal Concentrado'. Grey coloured, site applied cement based coating, intended to be used to waterproof concrete. Mix coating with water in a volume ratio of 5:2. Apply to pre-wetted cement and allow to cure for 1 hour@5°C. Pre-wet the cement before applying a second coat and then dry cure for 2 hours@5°C before wet curing for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`DR-PNL-WT Tank Panel`. Grey coloured GRP panel manufactured by hydraulic press moulding. For use with water up to 50°C.
`HYUNDAE Tank Panel`. Grey coloured GRP panel manufactured by hydraulic press moulding. For use with water up to 50°C.
`HYDROFAS'. Black coloured, extruded polyethylene (PE 80) pipe. For use with water up to 23°C.
'Eco-Hydroatlas'. Grey coloured, extruded PVC-U pipe. For use with water up to 23°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Drei Bond 5330'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Marfran E DRW HOF 50A & Marfran E DRW HOF 90A'. Pale yellow coloured (transparent), injection moulded TPS-SEBS materials. Shore hardness between 50A & 90A. Tested in-radius size 1.1mm. For use with water up to 60°C.
AQUAECO RANGE OF WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
AQUAECO WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
AQUAECO WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. There is a flow restrictor and stainless-steel strainer on the inlet valve. The cistern is operated by a manual push button. Maximum operating pressure 8.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a lever operated dual flush syphon with full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres and incorporates a servicing valve and flexible hose on the inlet supply.The cistern is operated by a pnuematic push button Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
‘Type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) incorporating a float operated valve controlling the flow. The inlet hose incorporates an isolation valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass body with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Liquistore range of circular sectional cisterns with galvanised or aluminium panels and a butyl inner liner. Supplied with a float operated inlet valve, screened breather, screened overflow and a gate valve on the drain connection. Cold water use only.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate an isolation valve, stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. HTMDMRS model is supplied with a removable spout. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate an isolation valve, stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. HTMWMRS is supplied with a removable spout. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Some models are supplied with lever operated pop-up wastes. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted three-hole concealed mixer with a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of expansion vessels with galvanised or stainless-steel inlets, incorporating butyl rubber diaphragms. The inlet incorporates a plastic strainer (all models, except for WD model). For maximum working pressures please refer to model.
Non-metallic materials and components comply with BS6920 at 70°C
Filling link assembly with a nylon body and EPDM ‘O’-rings. The product incorporates a screwdriver operated shut off valve and two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). The product is also supplied with two screwdriver operated angled spherical valves and a mounting bracket. Maximum working pressure 10.0 bar. Cold water use only.
A range of blue epoxy coated steel reverse rinsing fine filters with a stainless-steel sieve and an EDPM O-ring. Supplied with two pressure gauges and metal ball valve on the drain. Maximum working pressure 16 bar. Maximum operating temperature 40°C.
Range of medical sterilised water filter cartridges with plastic bodies and EPDM ‘O’-Rings. Models MTFW-SLSS / MTFD-SLSS incorporate a check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum Working Temperature: 50°C.
Range of tap outlets with plastic bodies incorporating a filter within the body, incorporating a hollow fibre filter membrane. The inlet of the filter incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The filters are supplied with (and must be used with) a chrome plated brass adapter which incorporates a pastic flow regulator. Maximum operating temperature 60°C.
Uponor ‘Q&E Shrink-Fit’ range of plastic (PPSU) or brass fittings for use with Uponor Radi pipe (PEX): 12mm, Uponor Combi pipe (PEX/EVOH/PEX): 16-40mm, and Uponor Aqua pipe (PEX): 40-63mm. Jointing is achieved via swaging tool. Uponor ‘Q&E’ adapters for soldering, solder ends are for use with copper pipe (manufactured to EN 1057). Operating parameters when used with the following pipes: 12mm Radi pipe, 16-25mm Combi pipe and 40-63mm Aqua pipe: Maximum working pressure 12.0 bar @ 20°C. Maximum working pressure 6.0 bar @ 95°C. From November 2022: 32-40mm Combi pipe: Maximum working pressure 12.0 bar @ 20°C. Maximum working pressure 6.0 bar @ 70°C.
Range of Protecta-line multilayer pipes manufactured to BS EN8588, PE100 63mm to 355mm and PE80 25mm to 32mm. For use with : Mechanical compression fittings: 25-32mm (PE80 pipe), 63mm (PE100 multi pipe) Electrofusion fittings: 63-355mm (PE100pipe) Mechanical clamp-on fittings: 63-180mm (PE100pipe) PE to Copper Pipe Coupler transition fittings are for use with copper pipe (BS EN 1057) For below ground use. Maximum working pressure: 10 bar when used with SDR17 PE100 Protecta-Line pipes 12.5 bar when used with SDR11 PE80 Protecta-Line pipes 16 bar when used with SDR11 PE100 Protecta-Line pipes 12.5bar when used with copper pipe.
Ebco Poly B range of compression fittings with gunmetal bodies, for use with PE80 pipe (manufactured to BS EN 12201). For above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
‘Flowflex,’ ‘Lamontite’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057.
Range of copper and DZR brass press fit tap connectors for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of black coloured, PE100 butt fusion fittings for use with PE100 pipes (manufactured to EN 12201). Maximum working pressure for fittings used with SDR11 pipe is 16.0 bar and for fittings used with SDR17 pipe is 10.0 bar. For above and below ground use. Cold water use only.
Range of black polyethylene electrofusion fittings for use with PE100 pipe (manufactured to EN 12201-2). Please refer to model for maximum working pressures. For below ground and cold water use only.
WC dual flush drop valve comprising of a plastic body, silicone seating washer and an internal overflow. The valve is operated via a push button assembly (not included) for either full or reduced flush. Cold water use only.
Dual flush drop valve incorporating two push buttons that operate either full or reduced flush. The valve reduced flush assembly is adjustable to give different flush volumes. The valve incorporates an internal overflow (overflow can be fitted or blanked off). Cold water use only.
Dual flush drop valve with ABS body and silicone seal. The valve is operated via a lever assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of heat exchangers connected to copper waste pipe, Where the waste is discharged down a “rotator” into a copper waste pipe, and potable water is returned to the shower/heating device via a copper double walled jacket around the copper waste pipe. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C
Range of electric instantaneous water heaters. The DEX and DCX models incorporate a spherical ball valve on the inlet. The CEX and DEX models incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet incorporates a strainer. Maximum working pressure 10 bar (DEX models only) All other models open outlet. Maximum operating temperature: ES3/4/5 and Zip Hydrotap G4/G5 ranges – 65ºC. CEX, DEX and DCX ranges - 70°C.
"Greenstar" range of indirect heat interface units and "Flow 8000" (added December 2024) range of direct heat interface units providing heating and instantaneous hot water. The heating system incorporates an expansion vessel. The products are sold with or without a prefix kit (see model), which comprises of a mounting bracket that includes spherical valves for all circuits. The "Greenstar" indirect models include a pressure relief valve (set at 3.0 bar) on the space (central) heating circuit. Greenstar models: Maximum working pressure district heating 10.0 bar. Maximum working pressure space heating 2.5 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary). Flow 8000 models (added December 2024): Maximum working pressure district and space heating 10.0 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary).
Range of wall mounted, gas-fired, condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and a pressure relief valve set at 3.0 bar. The inlets to the domestic hot water and primary circuits each have a screwdriver operated angled spherical valve. Both include a ½” BSP (M) connection for a filling link. The Greenstar CDi models only are supplied with an integral charging link (CAB device) verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature of primary circuit is 82°C. Maximum operating temperature of secondary circuit is 60°C.
Range of electric combination boilers providing heating and instantaneous hot water. The heating system incorporates an expansion vessel and pressure relief valve (set at 3.0 bar). The DHW inlet and outlet incorporate spherical servicing valves. Fittited with a CAB device keyless filling link, verifired by test, suitable for category 3 backlfow protection. Maximum working pressure on central heating circuit 2.5 bar & Domestic Hot Water 10bar. Maximum operating temperature 80°C
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Hydraulic block assembly comprising of a flow regulator, central heating pump assembly and a stainless-steel plate heat exchanger. Maximum working pressures: DHW circuit: 10.0 Bar Central heating circuit: 2.5 Bar Maximum operating temperature: DHW Circuit: 65.0°C Central heating circuit: 90.0°C
Hydraulic block incorporating heat exchangers with pressed stainless-steel plate bodies and copper brazing. Product also incorporates primary and secondary water way with PPS plastic fittings and adaptors and a flow adjustment valve. Maximum operating temperature: Central Heating Circuit: 90°C, Direct Hot Water Circuit: 65°C. Maximum working pressure: Central Heating Circuit: 2.5 bar, Direct Hot Water Circuit: 10 bar.
Water meter with a DZR brass body, stainless steel temperature sensors and EPDM ‘O’-rings. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘RSM’ range of ultrasonic water meters with blue epoxy coated ductile iron bodies, stainless steel transducer and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of static ultrasonic bulk water meters with stainless steel bodies and EPDM 'O'-rings. The products are supplied with two sets of optional (green) gaskets. Maximum operating temperature: Products marked T50: 65°C. Products marked T30: cold water use only.
Range of water meter manifolds with gun metal bodies and ball valve with either a quarter turn stop valve or screw down stop valve. The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of concealed thermostatic mixing valves with DZR brass bodies incorporating a thermostatic cartridge controlling the temperature. The inlets incorporate asingle check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.
Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.
Range of shower handsets and shower heads. The shower handsets have a plastic body (white), NBR ‘O’-rings, and a coloured locking ring around the shower face (see model section). The shower heads have a plastic body (white or chrome plated 02-093173 model), NBR ‘O’-rings, directional adjustment (ball joint) and a coloured interlocking ring either surrounding or central to the shower face (except for the 02-093165 and 02-093173 models which have no ring). The Wall shower T-L models have a combined NBR washer and stainless steel strainer on the inlet.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Spherical valve with a brass body and ball, PTFE seat, EPDM ‘O’-rings, a lever operating member and a drain connection outlet. Compression end connection for use with copper pipe (manufactured to BS EN 1057). The product is supplied with a brass cap and an EPDM washer which is interchangeable with the hose union spigot outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of draining taps with a brass or chrome plated brass (337020 CST model) body, rising spindle headwork, and EPDM seals and washers. Maximum working pressure 10.0 bar. Maximum operating temperature - 337221,337231 and 337004 CST models: 85°C, all other models: 65°C.
Screwdriver operated spherical (drain) valve with a brass body, brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The JMYG-064 1/2” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of PEX lined, interlocked, metal shower hoses. Maximum operating temperature 60°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Vacuum relief valve with a DZR brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 99˚C
Range of automatic air venting valves with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, manually operated, concealed blending valves with chromium plated brass bodies and either brass or stainless-steel trim (see model). The product incorporates a ceramic cartridge headwork with a single lever operating member. The product is supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ¾” captive nut end connection for installation on the outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valves (Chrome plated) brass body. Incorporating a ceramic cartridge headwork controlling the flow to the overhead shower and shower handset using a dome type operating member. The temperature is controlled via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The inlets incorporate stainless steel strainers, screwdriver operated spherical valves and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product includes, a riser rail, shower head with a stainless-steel strainer at the inlet, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valves (Chrome plated) brass body. Incorporating a ceramic cartridge headwork controlling the flow to the overhead shower and shower handset using a cube type operating member. The temperature is controlled via a thermostatic cartridge with a cube type operating member incorporating a manual override button. The inlets incorporate stainless steel strainers, screwdriver operated spherical valves and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product includes, a riser rail, shower head with a stainless-steel strainer at the inlet, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valves (Chrome plated) brass body. Incorporating a quarter turn ceramic disc headwork controlling the flow to the shower handset using a cubed type operating member. The temperature is controlled via a thermostatic cartridge with a cube type operating member incorporating a manual override button. The inlets incorporate stainless steel strainers, screwdriver operated spherical valves and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product includes, a riser rail, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves incorporating brass bodies (various finishes), self-cancelling diverter and self-closing headwork. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member. Models 1.1967.001, 1.1967.002, 1.1967.003 & 1.1967.004 are supplied with a shower hose, handset and riser rail and overhead shower. Models 1.1967.005, 1.1967.006, 1.1967.007 & 1.1967.008 are supplied with a shower hose, handset, riser rail & bath filler. Models 1.1967.009, 1.1967.010 & 1.1967.011 are supplied with a shower hose, handset and riser rail, overhead shower & bath filler. Maximum working pressure 5.0 bar. Maximum operating temperature 50°C.
Range of thermostatic shower panels incorporating a single sequential thermostatic control valve with a single lever operating member and flexible riser kit. Each inlet supplied with a servicing valve, EPDM o-ring and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with black lined PVC shower hoses and chrome plated shower handsets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of combined temperature and pressure relief valves incorporating DZR brass bodies, and a silicone diaphragm. The valves are pre-set at 4.5, 6.0, 7.0 or 10 bar (see models). The valves incorporate a manually operated rotational easing gear and are for use with copper pipe (EN1057) Please refer to model for maximum working pressure. Maximum operating temperature 95°C
Fire hydrant with a ductile iron and blue epoxy powder coated body and EPDM O-rings, operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar. Maximum operating temperature 70°C
Range of pressure reducing valves with DZR brass bodies, integral stainless steel strainer, and EPDM ‘O’-rings and membrane. The oulet pressure is adjustable between 1.5 bar and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 70°C.
Range of pressure reducing valves with DZR brass bodies adjustable between 1.0 and 6.0 bar. The valves incorporate a stainless steel strainer. Maximum supply pressure 25.0 bar or 16.0 bar (see model). Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of combination valves with a DZR brass body incorporating a pressure reducing valve, a ball valve, pressure gauge and water meter port. The outlet incorporates two single check valve cartridges, verified by test suitable for backflow to fluid category 3. Maximum working pressure 16 Bar Outlet pressure in the range 6.0 to 1.5 bar. Maximum operating temperature 80°C
Range of in-line adjustable pressure reducing valves with DZR brass bodies and NBR ‘O’-rings. The valve incorporates a test port. The outlet pressures range from 1.5 bar to 6.0 bar. Maximum supply pressure 25.0 bar. Cold water use only.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of inline and angled screwdriver or lever handle operated spherical valves with (chromium plated) brass bodies, chromium plated brass ball, NBR ‘O’-rings. For use with copper pipe manufactured to EN 1057 Maximum working pressure 16.0 bar at 30°C and 5 bar at 99°C Maximum working pressure 6.0 bar. Maximum operating temperature 90°C (model TX480 only)
ISIS range of single lever and T type operated spherical valves with DZR brass body and ball (chrome plated), and PTFE seals. Maximum working pressure 40.0 bar (¼”, 3/8”, ½”, ¾”, 1”, 1 ¼”, 1 ½”, & 2” models) Maximum working pressure 10.0 bar (2 ½”, 3” & 4” models) Maximum operating temperature 100°C
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10.60982.015.CP12-8510) Maximum working pressure 25.0 bar (model 10.62022.015.CP12-8510) Maximum working pressure 40.0 bar (models 10.61062.015.CP12-8510 & 10.61062.022.CP12-8510) Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 25.0 bar (model 5059340245713) Maximum working pressure 40.0 bar (models 05316984 & 05316960) Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated ). For use with copper pipe (EN1057). Maximum working pressure 25.0 bar (model 76696) Maximum working pressure 40.0 bar (models 77164& 68376) Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 40.0 bar Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 999698) Maximum working pressure 25.0 bar (model496877) Maximum working pressure 40.0 bar (models 570500 & 570622) Maximum operating temperature 85°C.
Spherical valve with DZR brass body and butterfly operating member, for use with copper tube (manufactured to EN 1057). The valve incorporates a drain valve. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass (CW617N) or DZR brass (CW511L) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (inline, angled and tee) with chrome plated brass bodies and ball. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 999698) Maximum working pressure 25.0 bar (model 496877) Maximum working pressure 40.0 bar (models 570500 & 570622) Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Double regulating valve with a bronze body, incorporating a DZR brass disc face with PTFE seat. The product incorporates two test points each with an EPDM ‘O’-ring. Maximum working pressure 25.0 bar. Maximum operating temperature 70°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of UV disinfection units with stainless steel bodies & quartz tubes. All models incorporate a spherical valve on the drain outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C
Range of floor or wall mounted water refill units. The flow is controlled via self-closing headworks with a dome type push button operating member. The outlet incorporates a bottle filling outlet with an aerator. The inlet incorporates an isolation valve, a drain valve and an approved double check valve suitable for backflow protection against fluid category 3. Maximum working pressure – 5.0 Bar, cold water use only.
Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.
'Bottom Plate K3'. Off-white (opaque) coloured, injection moulded POM component. For use with water up to 65°C.
'T195 NS sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'T11 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'Eurokote 480 FC'. Site applied, red coloured (once mixed), two part epoxy coating consisting of a resin and hardener. Mix, apply and cure (fully dry) in accordance with manufacturer's technical data sheet dated 23/09/2021. For use with water up to 23°C.
'420 OE UHMWPE'. Multi-layered (7 layers), Ultra High Molecular Weight Polyethylene hose manufactured by wrapping on a mandrel. The inner layer is white coloured polyethylene, and the outer layer is blue coloured rubber. For use with water up to 23°C.
'509 OE/UHMWPE' hose, manufactured by mandrel wrapping and vulcanisation. Multi-layered hose comprising of a clear PE inner layer, blue coloured EPDM second layer, white coloured reinforcement third layer, blue coloured EPDM fourth layer, grey coloured helix wire fifth layer and blue coloured EPDM outer layer. For use with water up to 23°C.
'Hydro 90'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'June 2022'. For use with water up to 85°C.
'Sinopec Drinking Water Pipeline Sealing Lubricant (Product Code: 523478)'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Brett Martin B9333 & B9444'. Blue coloured lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'IRRIPLASTEC PE 100 WATER'. Dual layered, extruded pipe comprising of a white coloured (opaque), PE inner layer and a black coloured, PE outer layer. For use with water up to 23°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Pipes'. Black coloured (with dark blue stripe), extruded HDPE pipe. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Fittings'. Black coloured, HDPE fittings manufactured by either injection moulding or butt fusion welding. For use with water up to 60°C.
'PPHS40'. Pale grey coloured, injection moulded PP material. For use with water up to 23°C.
'Alfaidro & Water Pipe PPR Green Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 85°C.
'Aquatherm Green' range of extruded, polypropylene pipes, for use with water up to 85°C. (1) Aquatherm Green Pipe. Single layered, green coloured polypropylene pipe. The SDR11S pipe has four, blue longitudinal stripes on the exterior of the pipe. (2) Aquatherm Green Pipe (formerly named Fusiotherm Fibre Composite Pipe). Triple layered pipe consisting of a light green coloured polypropylene inner layer, glass fibre reinforced, polypropylene middle layer and light green coloured polypropylene outer layer. The pipe has dark green stripes on the exterior of the pipe.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EWDRI 50, EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 0.69mm. 'EWDRI 50' is for use with water up to 70°C. 'EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80' are for use with water up to 60°C.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'Astral PVC Gel'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted electric showers (various finishes). The GSD/BETTER models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/DSK/ENTRY models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). Incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). The GSD models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/ models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of commercial, front loading, heat pump tumble dryers with flow controlled via a solenoid valve. Maximum working pressure 8.0 bar. Cold water use only.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet incorporates a flow regulator and the spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly with stainless steel body. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. The products are supplied with plastic backnuts and a stainless steel braided PEX lined flexible hose assembly for installation between the tap and the solenoid valve. The HK-Rib model is supplied with a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. The products are supplied with plastic backnuts and a stainless steel braided PEX lined flexible hose assembly for installation between the tap and the solenoid valve. The HK-Cha models added September are also supplied with a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes, see models). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products incorporate a hand dryer feature that are activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products are supplied with a metal backnut. Maximum working pressure 8.0 bar. Cold water use only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator and the inlets incorporates stainless steel strainers. Models 351500 & 351510 incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
‘Tubular’ range of wall mounted spout outlets (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The box assembly incorporates a solenoid valve, screwdriver operated spherical valve and the spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 1.0 bar. Maximum operating temperature 65°C
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only
Range of WC flushing cisterns incorporating a side entry BS 1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of flushing valves (gunmetal body) which incorporate a screw down stop valve, spherical valve and air gap to drain. Maximum working pressure 10.0 bar. Cold water use only.
Tundish incorporating a plastic body, nut and olives. The tundish complies with the requirements of air gap to drain. Maximum operating temperature 100°C
Range of tundishes with black plastic bodies. The products comply with the requirements of an air gap to drain.
Non-metallic materials and components comply with BS6920 at 65°C
Range of boiling water dispensers incorporating plastic (3-7.5 litre models) or stainless steel (10-40 litre models) cisterns with silicone ‘O’-rings and seals. The flow to the internal reservoir is controlled via a float valve. The internal reservoir incorporates an overflow which acts a vent. The inlet incorporates a plastic filter. Water is dispensed using either a lever or push button (PLUS models only) operated self-closing tap. Maximum working pressure 5.0 bar. Maximum operating temperature 98°C. Cold supply only.
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with various - operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single-hole, single outlet, (swivel), combination tap assembly, (chrome plated brass body) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The inlets incorporate screwdriver operated isolation valves incorporating approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (swivel) combination tap assembly (brass body – various finishes), incorporating two ceramic cartridge headworks with single lever operating members, with the upper headwork functioning as a manual diverter, diverting flow between the spout outlet and shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure: 10 Bar. Maximum operating temperature 65°C.
Wall mounted two hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Concealed, wall mounted, three-hole, single outlet (fixed) combination tap assembly (brass body - various finishes) incorporating quarter turn ceramic disc headwork. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Sensor control boxes, flow is controlled using a solenoid valve assembly. Flow is activated via infra-red sensor and product incorporates a stainless steel filter and EPDM ‘O’-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 75°C.
Range of in-line water filters with polypropylene bodies. Maximum working pressure 8.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at cold water use only°C
‘Unidelta’ brass compression fittings for use with ‘Unidelta UniTerm’ PEX pipe. Maximum working pressure 8.0 bar @ 85°C, 20.0 bar @cold water use.
‘Buteline Polybutylene Plumbing System’ comprising of DZR brass or plastic fittings for use with Buteline polybutylene, EVOH barrier pipe (white or grey). Maximum working pressure 16 bar @ 23°C, 7.0 Bar @ 82°C.
Range of brass or copper capillary solder ring fittings for use with copper pipe. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘Flowflex’ and ‘Lamontite’ ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Primaflow ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
CB ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
'Dudley Niagara` range of pneumatically operated single and dual flush drop valves. The flush assembly of the dual flush valve is adjustable to give different flush volumes. The valves are operated via a remote button connected by a plastic tube and incorporates an internal overflow. Cold water use only.
Range of dual flush WC drop valves with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Dual flush WC drop valve with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
‘G5 BC’ range of command centres that provide instant near boiling and chilled water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
‘G5 BCS’ range of command centres that provide instant near boiling, sparkling and chilled water (all filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products incorporate a pressure reducing valve (adjustable outlet pressure between 2.25 and 2.75 bar) on the supply to the carbonator unit. The carbonator inlet incorporates a non-return valve. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum inlet supply pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
‘G5 BCU60 UV’ Command centre that provides instant near boiling and chilled water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combinations of solenoid valves and electronic pumps to the outlets. A UV unit is incorporated on the outlet from the chilled water tank. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
Hydraulic block incorporating a stainless steel and copper brazed plate heat exchanger, plastic fittings and adaptors, recirculation pump and a flow adjustment valve. Maximum operating temperature: Central Heating Circuit: 90°C, Direct Hot Water Circuit: 65°C. Maximum working pressure: Central Heating Circuit: 2.5 bar, Direct Hot Water Circuit: 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of in-line ultrasonic water meters with DZR brass bodies. The following sizes only include a plastic strainer, DN15 - DN32 sizes (incorporated), DN40 size (optional). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of water meters with brass (CW724R & CC770S) and plastic (Composite) bodies, incorporating plastic strainers and EPDM ‘O’- rings. Maximum working pressure 16.0 Bar. Temperature: 60.0°C for brass (CW724R & CC770S) models & Cold water use only for composite models.
Range of ultrasonic water meters with plastic bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with black epoxy coated bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of pressure, flow and temperature sensors. The VFI sensors have stainless steel bodies, all other models have plastic bodied sensors. The MFS and VFS models are supplied with a plastic (composite) or stainless-steel flow pipe. The VFI models are supplied with a stainless-steel flow pipe. The products can also be supplied with a range of fittings/end connections (see model and size). Maximum working pressures: ITS, LPS, RPS, MFS (composite flow pipe) and VFS (composite flow pipe) models: 24.0 bar. CPS models (added February 2024): 24.0 bar. DPS: Models with vent hole: 16.0 bar. All other models: 24.0 bar. MFS (stainless steel flow pipe) and MFS (stainless steel flow pipe): 30.0 bar. VFI non-flanged models: 30.0 bar. VFI flanged models: 30.0 bar or as per flange PN rating 16.0 bar or 25.0 bar (whichever is lower). Maximum operating temperature 99°C.
Permanent filling device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. If the mains pressure is adequate and there is a drop in system pressure, then the two solenoid valves operate to allow water into the system via the transfer chamber. At all other times the normally open solenoid valve drains the transfer chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 5.0 Bar. Cold water use only.
Flow meter with stainless steel body. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
CR(I)(N)(E) ranges of multistage centrifugal pumps incorporating stainless steel impellers, intermediate chamber and outer sleeve. CR(E) versions have cast iron bases and pump heads coated with black cathodic paint. CRI(E) and CRN(E) versions have stainless steel bases and pumpheads. The pumps are available with the following shaft seals HQQ*, HUU*, HUB*, HQB*, where * can be E for EPDM and V for FKM. Maximum working pressures: CR1, 3 or 5 (2-36 stages) Oval flange: 16.0 bar. CR1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange: 25.0 bar CRI/N1, 3 or 5 (2-36 stages) Flexi clamp with oval flange connection: 16.0 bar CR/I/N1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange, PJE, Flexi clamp or Triclamp: 25.0 bar CR10 (1-16 stages) Oval flange or DIN/ANSI/JIS flange: 16.0 bar. CR10 (17-22 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI10 (1-16 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI10 (17-22 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar CRN10 (1-22 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR15 or 20 (1-7 stages) Oval flange: 10.0 bar. CR15 or 20 (1-10 stages) DIN/ANSI/JIS flange: 16.0 bar. CR15 or 20 (11-17 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI15 or 20 (1-7 stages) Flexi clamp with oval flange connection: 10.0 bar CRI15 or 20 (1-10 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI15 or 20 (11-17 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CRN15 or 20 (1-17 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR models: Cold water use only. CRI/CRN models: Cold water use only and from April 2023 99°C.
CR(N)(E) ranges of vertical multistage centrifugal pumps with stainless steel (CRN models) or black polymer coated cast iron bodies (CR models) and a stainless steel impeller. The products are available with or without a sensor. Maximum working pressure: 16.0 bar - CR(N)(E) 32 range with 1-7 stages, CR(N)(E) 45 range with 1-5 stages, CR(N)(E) 64 range with 1-5 stages. 30.0 bar - CR(N)(E) 32 range with 8-14 stages, CR(N)(E) 45 range with 6-11 stages, CR(N)(E) 64 range with 6-8 stages. 33.0 bar - CR(N)(E) 45 range with 12-13 stages. Maximum operating temperature - CR models are cold water use only. CRN models are cold water use only up to February 2nd 2023, and 99°C from February 3rd 2023.
Range of circulator pumps with brass bodies, plastic impellor, and EPDM ‘O’-rings and seals. The COMFORT 15-14 BX prefix models incorporate a screwdriver operated isolation valve on the inlet and a non-return valve at the outlet. These are housed within 1” BSP (M) x ½” BSP (M) adaptors. Maximum working pressure 10.0 Bar. Maximum operating temperature 95°C.
Range of multistage pumps (VL and CL series) and submersible pumps (VN, CN, ES and CS series) with stainless steel bodies and impellers and NBR gaskets and ‘O’-rings. Maximum working pressure 15.0 bar (VL and CL series pumps only).
Range of circulator pumps with stainless steel bodies and a plastic impeller. All models are available with a plastic (composite) rotor can, the MAGNA1 range is also available with a stainless-steel rotor can in the DN32 flanged, threaded 1½ & 2” sizes only. The MAGMA3 models have a differential pressure sensor. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of shower columns with an integral brass body and an aluminium painted column with chrome plated upper. Flow is controlled by a solenoid valve activated by an infrared sensor. The shower head inlet incorporates a combined NBR washer and stainless steel filter. The shower outlet incorporates a plastic flow regulator. The product is supplied with an inline ½” BSP (M) x ¾” BSP (F) screwdriver operated spherical valve with chromium plated brass bodies and ball for installation on the inlet. The product drains down after each use via an integral LLDPE tube leading to a drain outlet at the base of the column. Maximum working pressure 8.0 bar. Cold water use only.
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Wall mounted and ceiling mounted shower arms (chromium plated brass).
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall and ceiling mounted shower arms with (brass bodies - various styles and finishes). Maximum operating temperature 60°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Drain cock with a plastic body. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 75°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of drain taps with a brass body and rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of brass end connections (see models). “DN 9.5 ½” compression with ISO valve” model also incorporates a screwdriver operated isolation valve. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Qualflex classic range of stainless steel braided EPDM lined flexible hoses incorporating EPDM O-rings. Maximum working pressure at 20°C ,10.0bar and maximum working pressure at 65°C , 6.0bar. Maximum operating temperature 65°C.
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range wall mounted, concealed, thermostatic shower valves (chrome plated brass, trim sets) incorporating a quarter turn ceramic disc headwork that controls the flow using cube or dome type operating members. The temperature is controlled independently via a thermostatic cartridge also cube or dome type operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with fixed arms and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, thermostatic shower valves incorporating half turn ceramic disc headworks controlling and diverting the flow and the temperature is controlled independently via a thermostatic cartridge, both using either round or square operating members. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products can be supplied with wall outlets, fixed arms, shower handsets, shower hoses and overhead showers. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of T-type thermostatic mixing valves (chrome plated brass bodies). Temperature is pre-set under fixed cap. The inlets incorporate fibre washers, stainless-steel EPDM strainer washers and approved single check valve cartridges, however, (the complete product has not been fully tested to demonstrate it provides backflow protection). The inlets for models MT503CP-ISO & MT503CP-ISOELB also incorporate screwdriver operated isolation valves. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating ceramic disc diverter controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate screwdriver operated isolation valves, stainless-steel EPDM strainer washers and approved check valve cartridges, however, (the complete product has not been fully tested to demonstrate backflow protection). The products are supplied with a shower handset, shower head, hose, and riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. Model RYBS01 incorporates cube type operating members. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with shower hoses, shower handsets and riser rail assemblies. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted thermostatic bar shower mixer, (chrome plated brass body), incorporating a quarter turn ceramic disc headwork controlling the flow with a cubed type operating member. The temperature is controlled independently via a thermostatic cartridge with a cubed type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers and approved single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The product is supplied with a shower hose, handset, and riser rail assembly. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of thermal circulation valves with gunmetal bodies and EPDM ‘O’-rings. Models incorporate drain valves. Maximum operating pressure 16.0 bar. Maximum operating temperature 90°C.
T-type thermostatic blending valve with a brushed chrome, DZR brass body. Temperature is pre-set under a fixed cap. The inlets incorporate stainless steel strainers and single check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of T type thermostatic blending valves (chromium plated, DZR brass) Maximum working pressure 10.0 bar. Maximum operating temperature 62°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated double regulation and commissioning valves with gunmetal bodies, incorporating a PTFE sealing ring and EPDM ‘O’- rings. Flow is controlled via a non-rising spindle headwork. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of swing gate non-return valves (resilient trim) with blue epoxy coating ductile iron bodies, epoxy coated ductile iron gate with EPDM valve seat and hydraulic damper. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 45°C or 65°C, please refer to model.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM membrane. Maximum inlet supply pressure 16.0 bar. Outlet pressure 1.5 bar to 6.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of in-line, adjustable pressure reducing valves, with a DZR brass body. The product incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3) and a shut off valve. Maximum working pressure 16 Bar Maximum outlet pressure between 1.5 bar and 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of pressure reducing valves with DZR brass bodies. The valves are adjustable in the range of 1.5 bar - 6.0 bar. Stainless steel strainer Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of core manifolds (DZR brass body) incorporating a pressure relief valve (plastic body), with an EPDM diaphragm and ‘O’-rings. For use with copper pipe (manufactured to BS EN 1057). The pressure relief valve is pre-set at 6.0 or 8.0 bar (see models). The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum operating pressure 16.0bar. Cold water use only.
Range of solenoid valves with plastic bodies and EPDM rubber diaphragms. The inlet incorporates an inner and outer plastic strainer, EPDM washer and a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of ‘IBall Vortex’ flow through valves with brass body and EPDM ‘O’-rings incorporating a plastic spherical valve and a drain tap. Maximum working pressure: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Lever operated spherical flow through valve with brass body and chrome plated brass ball, PTFE seals and EPDM `O` ring. The product incorporates a drain valve. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Screwdriver operated spherical servicing valve with chromium plated brass body, brass ball and EPDM O-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with stainless steel bodies and chrome plated brass ball. Maximum working pressure 68.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of inline spherical valves with brushed chromium plated brass bodies and balls, PTFE seats and NBR ‘O’-rings. The valves are intended to be actuated by a motor (not supplied), but can also be screwdriver operated. Maximum working pressures: ¼” to 1” = 40.0 bar, 1¼” = 32.0 bar, 1½” to 2½” = 30.0 bar and 3” = 25.0 Bar. Maximum operating temperature 85°C.
Range of inline spherical valves with brushed chromium plated brass bodies and balls, PTFE seats and NBR ‘O’-rings. The valves are intended to be actuated by a motor (not supplied), but can also be screwdriver operated. Maximum working pressures: ¼” to 1” = 40.0 bar, 1¼” = 32.0 bar, 1½” to 2½” = 30.0 bar and 3” = 25.0 Bar. Maximum operating temperature 85°C.
Range of push-fit spherical valves with a brass body (15HSV model only) or chromium plated brass bodies (all other models), chromium plated brass ball and EPDM ‘O’- rings. SV suffix models are screwdriver operated; all other models are lever operated. For use with copper tube (manufactured to BS EN 1057), PB pipe (manufactured to BS7291-2) or PE-X pipe (manufactured to BS7291-3). Maximum working pressure and operating temperature: 12.5 @ 20°C, and 3.0 bar @ 92°C.
Range of spherical valves (shut-off, stop and servicing valves) with either acetal or POM (from 20th December 2023) bodies and a lever type or screwdriver operated operating member. For use with John Guest LLDPE pipe. Maximum working pressure: 10.0 Bar @20°C and 7 Bar @65°C. Non-metallic materials and components comply with BS6920 at 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of spherical (HCVB) or isolation (HBVU) valves with plastic bodies incorporating EPDM ‘O’-rings and seals. HBVU metric (mm) models are available in black or white, HBVU imperial (”) models are available in white or grey, HCVB models are available in black only. HBVU models are lever operated, HCVB models are screwdriver operated. HBVU models are for use with LLDPE pipe (manufactured to DIN 8072). The HCVB 15mm model push fit connection is for use with PEX-b pipe (manufactured to EN ISO 21003 B1) and the HCVB 22mm models push fit connection is for use with PEX pipe (manufactured to BS7291-3). Maximum working pressures: HBVU models: 10.0 bar. HCVB models: 7.0 bar (HCVB models push fit connection), barbed (spigot) connections of HCVB models are open outlet use only. Cold water use only.
Talbot range of gunmetal screw down stop valves for use with MDPE PE80 pipe (manufactured to EN12201). The products are supplied with loose (blue plastic) pipe inserts. Maximum working pressure 16.0 bar. Cold water use only.
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of front loading commercial washing machines with flow controlled by solenoid valves and discharged via a type `AD` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a dual layer composite supply hose (blue outer/black inner). Maximum working pressure 5.0 bar. Cold water use only
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
'Support Ring F1'. White coloured, injection moulded acetal support ring. For use with water up to 85°C.
'XXDT ST'. White coloured, dry pressed and sintered, ceramic disc. For use with water up to 85°C.
'SEDALOX Ceramic Disc'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'CEC-GFS Enamel, Black Blue RAL5004'. Factory applied, blue/black (appears black) coloured, enamel coating. Apply as per manufacturer's instructions 'ZZ-Ins001', dated '2021.01.01'. GFS-G base glaze: dry for 15 Minutes at 200°C then fire for 12 minutes at 870ºC. GFS-S surface glaze: dry for 15 Minutes at 200°C then fire for 10 minutes at 830ºC. For use with water up to 85°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RF (Riyadh Foundry)'. Factory applied, grey coloured cement. Mix cement, sand and water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instruction 'WI.PR.07', revision '01/01/', dated '16.02.2022'.. Cure for 3 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquastore'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquasystem'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquatank'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
‘PureOne hose’ (formerly known as ‘Clearwater hose’). Multi-layered hose manufactured on a mandrill by hand, consisting of a colourless, transparent PE inner layer and a blue coloured EPDM outer layer. Please note that the hose has many layers but the approval describes only the inner and outer layers. For use with water up to 50°C.
'TUSIL® ACQUA HT & TUSIL® ACQUA'. Multi-layered hoses comprising of a white coloured, silicone rubber inner layer, white coloured silicone rubber/polyester middle layer and blue coloured outer layer. The hose is made by vulcanisation on rigid mandrel. For use with water up to 85°C.
‘Multitubo’ multi-layered pipe. Extruded, triple layered pipe consisting of a white coloured, translucent PE-RT inner layer, aluminium middle layer and white coloured, opaque PE-RT outer layer. For use with water up to 85°C.
‘Palaplast Hydropal W PE80 & PE100 pipes’. Extruded, PE80 & PE100 pipes, both available in either blue colour or black colour (with blue stripe). All pipes are for use with water up to 23°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Supercast PVC Waterstop Hydrofoil'. Blue coloured, extruded PVC waterstop. For use with water up to 23°C. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The materials have been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Weld-On 725 Wet 'R' Dry Clear Solvent Cement'. Clear, colourless solvent cement. For use with water up to 23°C.
'Weld-On 724 C-PVC Grey Solvent Cement' Grey coloured solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 719 PVCu Clear Solvent Cement'. Clear, colourless solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C(±2°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Durapipe FIP & Astore PVCu Clear Solvent Cement'. Clear, colourless solvent cements. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maritex Aquapure Grade 5742'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Range of wall mounted, single hole, single outlet (fixed) tap assemblies (chromium plated brass) with a solenoid valve controlling the flow and activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connecting hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a angle valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by an electronically controlled flush valve. Maximum working pressure 10.0 bar. Cold water use only
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of break tanks and pump sets incorporating a Type AB airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10 bar. Cold water use only.
Range of tundishes incorporating a black or grey plastic body or mild steel painted black body (128-2001 CST, 128-2003 CST, 128-2004 CST & 128-2005 CST models only). Maximum operating temperature 85°C.
Tundish with a black plastic body and a straight through pattern. The product satisfies the requirements of an air gap to drain. Maximum operating temperature 65°C.
Range of dry trap tundishes with plastic bodies incorporating a spring-loaded diaphragm on the outlet. Maximum operating temperature 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a click type waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic disc headworks with single lever operating members (see models). The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65˚C.
Range of two-hole, single outlet fixed combination tap assemblies (brass bodies - various finishes, see model), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. BS6920 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts, shower hose and handset. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of five-hole, single outlet (fixed) combination tap assemblies with brass or stainless steel bodies in various finishes. The products incorporate a ceramic cartridge headwork controlling both the temperature and flow to the shower handset, and a quarter turn ceramic disc headwork controlling the flow via a thermostatic cartridge to the spout outlet. All have single lever operating members. Some models are supplied with a spout outlet which incorporates a plastic aerator. Some models are supplied with a shower hose and handset. The inlet to the spout assembly and the inlet of the shower handset each incorporate a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes - see model). Electronic controls on the left-hand side of the body allow the tap to dispense one or more of the following (model specification dependent): ambient, near boiling, chilled or sparkling water. The spout incorporates a plastic aerator on the Sparkling/Ambient/Chilled outlet, and a separate outlet for the near boiling water. All models incorporate a vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature of 98°C. All other circuits have a maximum operating temperature of 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes - see model). Electronic controls on the left-hand side of the body allow the tap to dispense one or more of the following (model specification dependent): boiling, chilled or sparkling water. Ambient (hot and cold) water is controlled via a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator on the Sparkling/Chilled and the Ambient outlet, and a separate outlet for the boiling water. Both model ranges incorporate a vent outlet within the tap spout for the boiling water circuit. Maximum working pressure 5.0 bar (Ambient (hot and cold) circuit only). 95458xxx models - Boiling circuit has a maximum operating temperature of 100°C. All other circuits have a maximum operating temperature of 65°C. 95459xxx models - Boiling circuit has a maximum operating temperature of 100°C. The ambient circuit has a maximum operating temperature of 65°C. The chilled/sparkling circuit has a maximum operating temperature of 60°C.
Zilmet range of cylindrical or tubular expansion vessels, epoxy coated carbon steel bodies with either Butyl or EPDM membranes and a stainless-steel connection. Please refer to models for maximum working pressures, as this varies by model and size. Maximum operating temperature 65°C.
Filling loop assembly comprising of a spherical valve, stainless-steel braided EPDM lined flexible hose and a double check valve assembly ((suitable for backflow protection against fluid category 3) which incorporates a lever operated spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line carbon block water filters and housings with polypropylene bodies. Maximum working pressure 8.0 bar. Cold water use only.
‘Atlas’ range of green fusion welded polypropylene fittings for use with ‘Atlas’ PPRGF or PPR pipes. Maximum working pressure 20.0 bar. Cold water use only.
Fluxo range of Brass & PPSU crimp fittings for use with ‘Fluxo’ PEX/Al/PEX Multilayer Pipe. Crimp joint is achieved by a TH profile crimp jaws. Maximum working pressure 10bar @ 70°C, 6Bar @ 95°C.
Geberit range of ‘FlowFit’ press Fittings for use with ‘Geberit FlowFit Pipe ML’ and ‘Geberit FlowFit Pipe coils ML’ (insulated and uninsulated) PERT/Al/PERT pipes. The fittings are made from PPSU or lead free silicon bronze. Operating parameters: 16.0 bar@cold water and 10.0 bar@70°C.
Range of press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with Multitubo multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Range of copper, bronze or DZR brass capillary solder ring fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure and operating temperatures: 8-28mm: 25.0 bar @ 30°C, 16.0 bar @ 100°C. 35-54mm: 25.0 bar @ 30°C, 16.0 bar @ 65°C and 10.0 bar @ 100°C.
‘Trustlene’ range of electrofusion and spigot fittings, with PE100 or brass bodies, for use with SDR11 PE100 pipe (manufactured to IS 4984: 2016). For use above and below ground. Maximum working pressure 16.0 bar. Cold water use only.
Range of Effast PVC-u solvent welded and/or threaded fittings for use with PVC-u pipe manufactured to (EN1452-2). Maximum working pressure 16.0 bar. Cold water use only.
Range of Redman fittings with mild steel bodies (polyamide coating) for use with Puriton II PE-AL-PE barrier pipe - For above and below ground and cold-water use. Jointing is achieved by hydraulic compression. Maximum working pressures: 12.5 Bar for 63mm SDR 11 PE80 pipe system, 10.0 Bar for 90mm to 180mm SDR 17 PE100 pipe system, 16.0 bar for 90mm to 180mm SDR 11 PE100 pipe system. Cold water use only.
Range of dual flush WC drop valves with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of WC dual flush drop valves with ABS bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
Range of WC dual flush drop valves with ABS bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
WC dual flush drop valve with ABS body and silicone seals. The valve is operated via a two push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
WC dual flush drop valve with plastic body silicone and rubber seal. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold Water Use Only.
Range of WC dual flush drop valves with plastic bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
‘G5 B’ & ‘G5 BA’ ranges of command centres that provide instant near boiling (filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The products can also be supplied with a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
Range of wall mounted, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system incorporating an expansion vessel, pressure relief valve set at 3.0 bar and flow regulators. The inlets to both domestic hot water and primary circuits are controlled via screwdriver operated angled spherical valve. The primary circuit can be filled via a built in CAB device, that has been verified by test (suitable for backflow protection against Fluid Category 3). Primary circuit: Maximum working pressure 2.5 bar. Maximum operating temperature 80°C. Secondary circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of water meters with blue epoxy power coated cast iron bodies, incorporating plastic turbines, NBR ‘O’-rings and gaskets. Maximum working pressure 16.0 bar. BS6920 50°C.
Range of water meters with (blue epoxy coated) brass bodies and plastic working chamber. The inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with blue epoxy power coated cast iron bodies, incorporating plastic turbines, NBR ‘O’-rings and gaskets. Maximum working pressure 16.0 bar. BS6920 50°C.
‘MJ-SDC plus’ range of water meters with brass bodies, incorporating plastic impellers. The inlets incorporate plastic filters. Maximum working pressure 16 Bar. Maximum operating temperature 50°C.
Range of in-line ultrasonic water meters with DZR brass bodies and a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Ultrims Ultrasonic range of in-line water meters with brass or plastic (-01 suffix models) bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of pressure reducing valve assemblies with brass bodies incorporating spherical stop valve, pressure gauge and double check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar. Maximum operating temperature 65°C
Range of hose assemblies. Models B0301-148036-000 & B0301-148038-000 comprise of a spherical valve, stainless-steel braided EPDM lined flexible hose and double check valve assembly (suitable for backflow protection against fluid category 3). Model B0301-148037-000 comprises of a double check valve assembly (suitable for backflow protection against fluid category 3), stainless-steel braided EPDM lined flexible hose and ‘T’ type spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Range of submersible pressure sensors and hydrostatic transmitters (supplied in lengths up to 1000m). Cold water use only.
Range of multistage centrifugal pumps, with stainless steel bodies (CRN models) or black coloured cataphoretic electrodeposition coated cast iron bodies (CR models), stainless steel sleeve and impellers. The products can be supplied with or without a sensor. Maximum working pressures (no. of stages in brackets): CR/CRN 95 (1-5): 16.0 bar. CR/CRN 95 (6-8): 25.0 bar. CRN 95 (9-12): 40.0 bar. CR/CRN 125 (1-4): 16.0 bar. CR 125 (5): 25.0 bar. CRN 125 (6-7): 25.0 bar. CRN 125 (8-12): 40.0 bar. CR 155 (1-4): 16.0 bar. CRN 155 (1-4): 16.0 bar. CRN 155 (5-6): 25.0 bar. CRN 155 (7-11): 40.0 bar. CR/CRN 185 (1-3): 16.0 bar. CR/CRN 185 (4-5): 25.0 bar. CR/CRN 185 (6-8): 40.0 bar. CR/CRN 215 (1-3): 16.0 bar. CR/CRN 215 (4-5): 25.0 bar. CR/CRN 215 (6-7): 40.0 bar. CR/CRN 255 (1-3): 16.0 bar. CR/CRN 255 (3-4): 25.0 bar. CR/CRN 255 (5-6): 40.0 bar. When a sensor is incorporated the maximum working pressure is as follows: 25.0 bar with either the IPS44 or VTU sensor, (unless they are used on a pump with a maximum working pressure of 16.0 bar, in this instance the lesser pressure applies). The MBS3000 sensor can be used on all models, the pump maximum working pressure applies. Cold water use only.
Range of two stage horizontal water pumps with plastic bodies, stainless steel impellers and shaft, incorporating EPDM gaskets and seals. The products also incorporate a non-return valve (not suitable for backflow protection) and an shock arrestor expansion vessel. Maximum working pressure 1.8 bar. Cold water use only.
Peripheral pump for mains water applications with a brass body and impeller, . The pushfit connections on the hoses are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 bar. Cold water use only.
Range of colour coded disposable shower kits incorporating a white PVC shower hose with EPDM washer and shower handset incorporating a plastic body (white), NBR ‘O’-rings, and a coloured locking ring around the shower face. Maximum working pressure: 5.0 bar Maximum working temperature: 60°
Range of shower riser kits and shower cradle kits. Models PSA006, PSA013, PSA007, PSA012, PSA002, PSA004, also incorporate a manual operated diverter with single lever operating member. Maximum operating temperature 65.0°C
Range of shower outlets incorporating brass bodies (various finishes) and NBR ‘O’-rings. Maximum operating temperature 85°C.
Range of plastic shower handsets available in various finishes. Maximum operating temperature 65°C.
Drain valve with a DZR brass body and rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of drain valves with bronze bodies, EPDM seat and ‘O’-rings. The products incorporate a rising spindle operating mechanism and a hose union outlet connection. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of drain taps with brass or DZR brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A Range of drain valves with bronze bodies incorporating brass bonnets, stems and baffles with EPDM seats and O’-rings. The products incorporate a rising spindle operating mechanism. Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of draining taps with DZR brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of nylon braided hoses with TPSiV inner liner and brass end connections incorporating EPDM washers.Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections (see models). Some models incorporate a screwdriver operated isolation valve. All compression and push-fit connections are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 7.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Hydravend range of PVC coated (grey or white in colour), hytrel lined, flexible thermoplastic hoses, incorporating a white quadruple layered hose with a black TPE inner lining. The hoses are supplied with plastic or brass end connectors and with or without servicing valves. Maximum working pressure and temperature: 12.0 bar Cold water use only.
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of cased and insulated stainless steel unvented water storage heaters. The DHW circuit includes a factory fitted combined temperature and pressure relief valve set at 6.0 bar and 90˚C. The product can be supplied with two possible safety kits (inlet control groups). One includes a pressure reducing valve adjustable between 1.5-6.0 bar, (but set at 3.0 bar), a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and a pressure relief valve pre-set at 4.5 bar. The other includes a pressure reducing valve pre-set at 3.0 bar, an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, and a pressure relief valve pre-set at 4.5 bar. The product is also supplied with an expansion vessel and a tundish. The compression connection of each inlet control group is for use with the following pipes: Both for use with copper pipe (manufactured to BS EN 1057). The inlet control group without an adjustable pressure reducing valve can also be used with PB pipe (with inserts) (manufactured to BS EN 7291-2:2010) and PEX pipe (with inserts) (manufactured to BS EN 7291-3:2010). Maximum supply pressure to inlet control group pressure reducing valve: 16.0 bar. Maximum working pressure 4.0 bar. Maximum operating temperature 99°C. Cold supply only.
Range of wall mounted, thermostatic shower valves, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks controlling the flow. The temperature is controlled independently via a thermostatic cartridge the temperature, both using single lever operating members. The inlets incorporate flow regulators, plastic strainers, screwdriver operated isolation valves and approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of flow control valves with epoxy coated ductile iron bodies. Auxiliary components include a needle valve, pressure reducing pilot valve and isolation valves. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range 0.6 to 1.2 bar. Maximum operating temperature 65°C.
Self-closing concealed shower valve assembly with (DZR) brass body incorporating a non-concussive headwork and dome type operating member (chromium plated brass). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of pressure reducing valves with DZR brass bodies. Maximum inlet supply pressure 25.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 70°C.
Range of in-line, adjustable, pressure reducing valves with DZR brass bodies and incorporating a stainless steel strainer. Maximum supply pressure 16.0 bar. Outlet pressure range 1.0 to 6.0 bar with an inlet pressure of up to 10 bar Outlet pressure range 2.0 to 6.0 bar with an inlet pressure above 10 bar Maximum operating temperature 60°C.
Range of pressure relief valves with plastic bodies and EPDM diaphragms and ‘O’-rings, Factory pre-set at 3.0 bar. Maximum operating temperature 110°C.
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
Range of in-line lever or screwdriver operated spherical valves with DZR brass bodies (nickel plated) and brass balls (chromium plated), EPDM ‘O’-rings and PTFE seats. The ball can incorporate a plastic flow regulator, or a stainless-steel strainer (within a plastic housing) inserted through the side port. Compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: Spherical valves only and those incorporating a stainless-steel strainer: 85°C. Spherical valves incorporating a plastic flow regulator: 60°C.
Range of inline, T-piece or angled screwdriver operated spherical valves with brass or chrome plated brass bodies and ball, for use with copper pipe to BS EN 1057 and Stainless steel to EN 10312. Maximum working pressure 10.0 Bar Models 1GLB311NP-SD, 1GLB411NP-SD, 1GLB111, 1GLB121 – 16.0 Bar Maximum operating temperature 85°C
Range of spherical valves with a brass body, brass ball, PTFE seats and lever type operating members. Maximum working pressure 40.0 Bar Maximum operating temperature 65.0°C
Range of spherical valves incoporaintg either brass (CP5R models) or nickel plated (CP12 models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of full port spherical valves with DZR brass bodies, chrome plated or (VIR REDOX) coated brass ball (see model). The products are either lever or handle operated (see model). The 33FFDRE models include a stem extension. Maximum working pressure 32.0 bar. Maximum operating temperature 100°C (wholesome water use), 130°C (closed circuit use only).
Range of gate valves with Red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of combined stop valve and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
Range of manually operated balancing valves with bronze bodies, DZR brass disc and EPDM rubber 'O’-rings. Both models have test points. The F9506 models also have a drain point on the high-pressure test side. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
‘G5 C’ command centre providing chilled (filtered) water via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The inlet to the command centre incorporates two approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum inlet supply pressure 5.0 bar. Cold water use only.
‘G5 CS’ command centre providing chilled or chilled sparkling water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The product incorporates a pressure reducing valve (adjustable outlet pressure between 2.25 and 2.75 bar) on the supply to the carbonator unit. The carbonator inlet incorporates a non-return valve. The product is supplied with a filter cartridge. The inlet to the command centre incorporates two approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum inlet supply pressure 5.0 bar. Cold water use only.
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
‘X086 Ceramic Dome’. Grey coloured, hydraulically pressed ceramic dome component. For use with water up to 23°C.
'Hilox 961'. Brown coloured, dry pressed ceramic material. For use with water up to 85°C.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'Rubalit IS95 White'. White coloured, dry pressed ceramic disc component. For use with water up to 85°C.
'YJ-AL2O3 95%'. White coloured, dry pressed and sintered ceramic disc. For use with water up to 85°C.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431 Primer for use with HYDRALFUN AC BLEU PAM RAL5005-CZL8190 Coating’. Factory applied, dark blue coloured (once applied), powder coating for use with two-part epoxy primer. Mix parts A & B of primer in a 100:10 mass ratio and apply as per manufacturer’s TDS dated February 2024. Cure for 24 hrs at 20°C. Apply coating as per manufacturer’s TDS dated February 2024 and cure for 21 days at 20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HYDRALFUN AC BLEU PAM RAL5005-CZL8190'. Factory applied, blue coloured acrylic paint. Apply as per manufacturer's TDS dated February 2024. Cure for 21 days@23°C. Between April 2024 and July 2024, the paint is for use with water up to 50°C. From August 2024 the paint is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HYDRALFUN AC NOIR PAM - CZL8579'. Factory applied, black coloured acrylic paint. Apply as per manufacturer's TDS dated July 2018. Cure for 21 days@23°C. For use with water up to 60°C.
'Drincable'. Blue coloured, extruded, EPDM rubber electrical cable. Shore hardness 50. Tested in-radius size 0.90mm. For use with water up to 23°C. This approval is for complete cable, the blue coloured outer part being the water contact layer.
‘Drinkflex Aquarius 3G1, 3G1,5, 3G2,5, 3G4, 4G1, 4G1,5, 4G2,5, 4G4 & 4G6’ range of polyolefine cables. The cables have an extruded, blue coloured polyolefine outer (water contact) layer and are available with 3 or 4 internal cores. For use with water up to 23°C.
'Saudi Drip HDPE PE100 pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'Asrene SP4808'. White coloured, compression moulded HDPE material. For use with water up to 65°C.
‘G&B Fissaggi Gebofix PRO VE-SF SISMIK’. Site applied, two part, grey coloured (once mixed) anchor resin. The material consists of Part A (shiny white liquid) & Part B (shiny black liquid). Mix, apply and cure as per ‘full curing of dry base material’ which appears in manufacturer’s Technical Data Sheet ‘rev. 05/2022’, For use with water up to 60°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
‘Drei Bond 5204’. Yellow coloured anaerobic adhesive paste. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies), incorporating a solenoid valve controlling the flow which is actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The product also incorporates an integral hand dryer. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 43°C
Wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies), incorporating a solenoid valve controlling the flow which is actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The product also incorporates an integral hand dryer. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 43°C
Range of BS1212-4 (2016) float operated valves for WC flushing cisterns, bottom or side entry type with plastic or brass ½’’ BSP inlet. The inlet incorporates a strainer, Compact models incorporate a delay fill function. Maximum working pressure 10.0 bar. For use with cold water only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (swivel nozzle) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with cross top or lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure - 5 Bar Maximum operating temperature - 60 °C
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Single hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pullout hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure; 5 Bar Maximum operating temperature 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and single lever type operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 65°C
Range of single hole, double outlet (swivel) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied or part of this approval) and a ceramic cartridge headwork with single lever operating member controlling the flow of normal mixed water. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 98.0°C.
Range of free standing sanitary macerating disposal units. The flow is controlled by solenoid valve and discharges via type a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Cold water use only.
Bed pan macerator with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 8.0 bar. Cold water use only.
Range of chemical dosing equipment. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Max operating pressure 5.9 bar. Cold water only
Range of cylindrical or tubular expansion vessels with epoxy coated carbon steel bodies. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C
Range of expansion vessels with white epoxy coated steel bodies and butyl diaphragm. Please refer to model for maximum working pressures. Maximum operating temperature 70°C. Maximum working pressure 10.0 bar (all except two models), 8.0 bar (24749 & 24809 only).
Range of medical sterilised water filter cartridges with plastic bodies and EPDM ‘O’-Rings. Models SMTFW-SLSS / SMTFD-SLSS incorporate a check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum Working Temperature: 50°C.
Range of filter cartridges. Maximum working pressure 8.0 Bar. Cold water use only.
Range of MULTITUBO tin-plated brass and PPSU press fit fittings for use with MULTITUBO multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘BORPLUS’ range of PP-RCT Socket Fusion fittings used with ‘BORPLUS PP-RCT FASER COMPOSITE STABIL’ pipe. Maximum working pressures at 16.0 Bar @ 23°C and 6.0 Bar @ 85°C.
Flowtech range of green butt welded polypropylene fittings for use with Flowtech’ PPRGF or PPR pipes. Maximum working pressure 20.0 bar. Cold water use only.
‘Hansen easy fit’ range of polypropylene compression fittings with EPDM ‘O’-rings for use with metric PE80 (20mm-63mm) and PE100 (32mm-110mm) pipe to AS/NZS:4130 and plastic pipe inserts. For above and below ground use. Maximum working pressure: See models. Maximum operating temperature: Cold water use only.
Range of ‘Isiflo Sprint’ push fit fittings for use with PE100 pipe (manufactured in accordance with EN 12201), for above and below ground use. Isiflo Sprint Family fittings can be installed with seal liners, support liners and without any liner. Maximum working pressure 16 bar. Cold water use only.
Range of stainless steel press fittings: SS316L stainless steel models are for use with SS316L stainless steel pipe manufactured to EN 10312.; SS304 stainless steel models are for use with SS304 stainless steel pipe manufactured to EN 10312. Crimp joint is achieved by a M profile crimp jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Allpex range of end feed capillary fittings and brazing fittings for use with copper tube (manufactured to BS EN 1057). EG fittings have gunmetal bodies, ED fittings have DZR brass bodies & EB fittings have brass bodies. For above ground use only. Maximum working pressure: 6mm – 34mm 25Bar, 34mm -54mm 25Bar, 54mm – 108mm 16Bar, 108mm – 159mm 5 Bar. Maximum operating temperature 30°C
WC dual flush drop valve with ABS body and silicone seals. The valve is operated via a two push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of WC dual flush drop valves operated via a two-push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of wall mounted, electronic tap assemblies which are set within a mirrored cabinet unit. The flow is controlled by a solenoid valve assembly and is activated via infra-red non touch operation. The units also incorporate a soap dispenser and hand dryer or paper towel dispenser. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Indirect heat interface unit with copper brazed, stainless-steel heat exchangers, providing heating and instantaneous hot water. The product incorporates an expansion vessel on the cold-water supply to the plate heat exchanger and a safety relief valve on the heating circuit set @ 2.5 bar. The DHW and heating circuits are both fitted with drain valves incorporating cover caps. Maximum working pressure 16 Bar (Primary), 10 Bar (DHW) & 3 Bar (Heating) Maximum operating temperature 95°C
Range of water meters with brass bodies and plastic turbines. The inlet incorporates a plastic filter. Maximum working pressure 16.0 bar. Maximum operating temperatures Sizes DN15-25 models: 50°C, sizes DN32-40 models: 85°C.
Range of in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with brass bodies, plastic turbines and plastic strainers on inlets. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Concealed, floor mounted basic set with DZR brass body. For use with floor standing combination tap assemblies. Maximum operating pressure 10 bar. Maximum operating temperature 70°C
‘Monsoon Standard’ range of single and twin ended shower booster pumps with brass bodies, brass impellers, EPDM seals and NBR ‘O’-rings. The inlet(s) of the pump body incorporate(s) a plastic strainer. Models with push fit connections include an integral isolation valve. Pushfit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of horizontal or vertical multi-stage pumps with a stainless-steel body (HM models) or cast iron body with blue coloured cationic resin coating (VM models), incorporating either plastic or stainless-steel impellers (see model), stainless steel sleeve, EPDM gaskets and seals. Maximum working pressure 10.0 bar / 16.0 bar (see models). Cold water use only.
Range of single or twin shower pumps with brass bodies, brass impeller supplied with flexible connection hoses that incorporate servicing valves. Maximum Working pressure 6 Bar Maximum operating temperature 65°C
‘Hydro MPC’ range of booster sets incorporating vertical multistage centrifugal pumps, butterfly valves, non-return valves (not suitable for backflow protection), pressure transmitters, pressure gauges, lever operated spherical valves, stainless steel blanking flanges and fibre/NBR gaskets. Maximum working pressure 16.0 bar. Cold water use only. ‘Hydro MPC’ range of booster sets incorporating vertical multistage centrifugal pumps, butterfly valves, non-return valves (not suitable for backflow protection), pressure transmitters, pressure gauges, lever operated spherical valves, stainless steel blanking flanges and fibre/NBR gaskets. Maximum working pressure 16.0 bar. Cold water use only.
Concealed, wall mounted elbow fitting with a brass body incorporating EDPM `O`-rings. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 70.0°C.
Range of in-line Y patterned strainers with flanged ductile iron bodies (blue epoxy coated) and stainless-steel mesh strainers. The strainers also incorporate a drain plug. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with flanged ductile iron bodies (blue epoxy coated) and stainless-steel mesh strainers. The strainers also incorporate a drain plug. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass body and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass or DZR brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain valves with a brass bodies, spindle and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless-steel braided TPS lined flexible hose assemblies incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves Push-fit fittings for use with: Copper Pipes manufactured in accordance with BS EN 1057 PB pipes manufactured in accordance with BS 7291-2 PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure 12.0 bar. Maximum operating temperature 65°C.
‘Qualflex Excel’ range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves. Push-fit fittings for use for with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.
Range of multilayer PVC hoses. Maximum operating temperature 65°C. Open outlet use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel braided, EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of Indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 90˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check cartridge, verified by test (suitable for backflow protection against fluid category 2) an expansion vessel and tundish. Maximum working pressure: Secondary: 4.0 Bar Primary: 3.0 Maximum operating temperature 99.0°C
Range of primary hot water buffer tanks consisting of stainless steel shells. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of primary hot water buffer tanks consisting of insulated enamel and Stainless steel shells. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection). Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
‘Rada’ electronically controlled thermostatic blending valve, with a stainless-steel body, EPDM ‘o’ rings and seals. Maximum working pressure; 13.8 Bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted thermostatic blending shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc two-way diverter headwork controlling the flow with dome or square type operating members. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with dome or square type operating members. The inlets incorporate a stainless-steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel or chrome plated iron disc. Products are either handwheel or gear operated. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Fire hydrant (screw down pattern type) with ductile iron body (blue epoxy coated). Maximum working pressure 16.0 bar. For above and below ground, cold-water use.
Range of fire hydrants with an epoxy coated, cast iron body, operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Range of fire hydrants with an epoxy coated, cast iron body, operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Fire hydrant with a ductile iron body (blue epoxy powder coated) operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of regulating and shut-off valves with brass bodies and EPDM ‘O’-Rings. Maximum working pressure 16.0 Bar for BSP (M) and 25.0 bar for BSP (F). Maximum operating temperature 85.0°C
Range of swing gate, non-return valves with (blue or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with blue epoxy coated ductile iron bodies and EPDM gaskets and ‘O’-rings (all models) and an EPDM diaphragm. Outlet pressure range: 1.5 - 6.0 bar. Maximum supply pressure 16.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with nickel plated DZR brass body. Maximum inlet supply pressure 25 bar. Maximum operating temperature 80°C
Range of angled pressure relief valves (pre-set at various pressures) with DZR brass bodies and EPDM diaphragms. Maximum working pressure: SEE MODELS Maximum operating temperature 99.0°C
Range of lever, handle or square operated (see models) spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of spherical valves incorporating nickel plated (brass bodies with chrome plated brass ball and operated via lever, handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of spherical valves incorporating DZR brass body, plastic ball and lever type operating members. The products also incorporate a drain valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10130420) Maximum working pressure 25.0 bar (model 10130379) Maximum working pressure 40.0 bar (models 10130277 & 10130345) Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating either brass (870228 &961665) or nickel plated (961159, 961708, 837973, 845188 & 845187) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever (1307 and 1333 models) or screwdriver operated (all other models) spherical ball valves with brass bodies and a chromium plated brass ball. Max working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line screwdriver operated spherical valves, with brushed chrome brass bodies and chrome plated brass ball. Maximum working pressure 16.0 Bar. Maximum operating temperature 99.0°C.
Series of brass valves with EPDM o-ring isolation valves with M profile press crimped connections to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spherical valve with a DZR brass body incorporating a redox coated DZR brass ball with a square head type operating member. Maximum working pressure 40.0 bar Maximum operating temperature 95°C
Range of brass spherical valves, incorporating chrome plated brass balls, butterfly type operating members and a drain off spigot connection that incorporates a rising spindle type headwork. For above ground use only. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of screwdriver operated spherical valves with brass bodies and balls (chromium plated).
Range of lever models S3727, S3737, S3747, S3758, 85986, 85987 & 85988 or screwdriver operated (all other models) spherical ball valves with brass bodies and a chromium plated brass ball. Max working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel plated brass bodies, chromium plated brass ball, PTFE seats and a drain valve. Maximum working pressure 25.0 Bar Maximum operating temperature 100.0°C
Range of spherical valves with either brass (UW24905 & UW24907 models) or nickel plated (UW24809, UW24906, UW24933, UW24908 & UW24934 models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass spherical valves, incorporating chrome plated brass balls, butterfly type operating members and a drain off spigot connection that incorporates a rising spindle type headwork. For above ground use only. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of lever operated spherical valves with brass bodies, incorporating a chrome plated brass ball. Model 7741345 incorporates a drain valve end connection. For use with copper pipe to EN1057. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of inline or angled servicing valves incorporating a white (-W and -01 suffix models) or grey (all other models) plastic body, chrome plated brass ball, EPDM washers and EPDM ‘O’-rings. The products are either lever operated (-H and -01 suffix models) or screwdriver operated (all other models). Push fit connections are for use with copper pipe (manufactured to EN 1057), John Guest BPEX pipe or PEX barrier pipe (manufactured to BS EN 7291-3) and John Guest BPB or polybutylene barrier pipe (manufactured to BS EN 7291-2). Maximum working pressure and operating temperature: 13.24 bar @ 20°C, 6.0 bar @ 65°C.
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated cast iron bodies and EPDM coated cast iron wedges, operated via non-rising spindle. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange drilling pattern). Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of cold-water inlet control groups consisting of an in-line, manually adjustable pressure reducing valve and a pressure relief valve pre-set at either 6.0 or 8.0 bar, housed within DZR brass bodies. The products incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. The pressure reducing valves also have stainless-steel strainers. Maximum inlet pressure 16.0 bar. Cold water use only. CWIC351300 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 6.0 bar CWIC351301 – Outlet pressure range 1.0 to 2.1 bar. Pressure relief valve set at 8.0 bar. CWIC351303 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 8.0 bar CWIC351306 – Outlet pressure range 1.5 to 6.0 bar. Pressure relief valve set at 8.0 bar
‘Ballorex’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘BOSS VENTURI’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with DZR brass bodies. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C.
STAD range of balancing valves with brass bodies, PTFE sliding washer and EPDM O-rings. Models are available with or without a drain port. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of manually adjustable thermal balancing valves (brass body) supplied with a temperature gauge. TREG models: Maximum working pressure 10.0 bar. Maximum operating temperature 99°C. SBTREG models: For use with copper pipe (BS EN1057), maximum working pressure 10.0. Maximum operating temperature of 95°C.
Drinking water fountain, incorporating of spherical valve, self-closing tap and pressure reducing valve enclosed within a metal housing. Maximum working pressure 25.0 bar. For cold water use only.
‘NATZINC EP9015 SC PART A-BI.5431’ primer for use with ‘HYDRALFUN AC NOIR PAM -CZL8579’ finish/topcoat. Factory applied, black coloured (once mixed and applied), two-part epoxy primer for use with acrylic coating. Mix base & hardener of primer in a 100:10 weight ratio and apply one coat as per manufacturers TDS ‘NATZINC EP9010 BI 5431’, dated ‘February 2024’. No cure required. Apply one coat of the topcoat as per manufacturers TDS ‘HYDRALFUN AC NOIR PAM CZL8579’, dated ‘July 2018’ and cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydrothen PE 100 Black Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Hydrothene (blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 85°C.
'VIALLI-De SDR 6 & SDR 7.4 PPR pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 Pipe with Aluminum Middle Layer'. Extruded PPR pipe with a green coloured inner and outer layer and aluminium middle layer. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 & SDR 7.4 Pipes with Glass Fibre Middle Layer'. Extruded PPR pipes with a green coloured inner and outer layer and a red coloured, glass fibre middle layer. For use with water up to 23°C.
'AquaTerra SDR 6 PP-R Pipes'. Green coloured, extruded PP-R pipes. 'AquaTerra SDR 7.4 PP-R Pipes', green coloured, extruded PP-R pipes were added to the approval in September 2024. All pipes are or use with water up to 85°C.
'Hidroten Fittings'. Grey coloured, injection moulded PVC fittings. For use with water up to 23°C.
'OLDAL 460'. Black coloured, injection moulded EPDM material. Shore hardness 50. Tested in-radius size 1.2mm. For use with water up to 85°C.
Wall mounted electric heater, incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
BS EN 14055 (2018) concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve discharging via a type AG airgap and a dual or single flush pneumatic or dual flush cable operated drop valve capable of full flush volumes of up to 6 litres with a reduced flush of up to 4 litres. The cistern is operated by manual push button/push plate. The side entry inlet valve is mounted internally and is supplied via a stainless steel braided EPDM lined flexible hose assembly which incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted single hole, single outlet (fixed), combination tap assembly (various plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet with a dome type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of non-verifiable double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. The products incorporate a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of tundishes with plastic bodies. The tundish complies with the requirements of an air gap to drain. Maximum operating temperature 85°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
Drayton GRP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VS11-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS11-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable |
The difference between models are the splines only, one has 20 and the other has 24.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CAP BASNW C | Chrome | 15mm compression | 5 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193838 X XXX | VARIOUS | 1/2" BSP | 10 bar | 65 °C | PPI | Body | No | Ceramic cartridge | C Clamp | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SAI BAS C | Chrome | M10 X 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 231827 | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | ||
| 257582 | Black | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MIO BAS C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| HMS MIO BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| CN SPH BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
HMS MIO BASNW C - (selling code for Homeserve without Waste) CN SPH BASNW C - (selling code for Crest without Waste)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| BQVEC BAS C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener | |
| VT2 BASNW C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193938 X XXX | VARIOUS | ½” BSP | 5.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 194828 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 181028 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (fixed) combination tap assemblies with either stainless steel (models 49xxS604WF & 49xxP704WF only) or brass (all other models) bodies (various finishes). The products incorporate a ceramic cartridge headwork with either single lever, cylindrical or no supplied operating members (see models). The spout outlets incorporate a plastic aerator and model 58xxL904F is supplied with a lever operated pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 80°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 235038 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 223238 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC BSNK C MT | Chrome | 15mm Copper Tail | 7.0 bar | 65 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet | |
| VAC BSNK WHT | Chrome | 15mm Copper Tail | 7.0 bar | 65 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet |
‘Arco,’ ‘Zero,’ ‘Slim’ & ‘Trenta9’ ranges of wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork and either a single lever operating member (Trenta9 models) or dome type operating member (all other models). The spout connection of the Arco models incorporates a plastic flow regulator. The spout outlet of all other models incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193806 X XXX | Various | ¾” BSP | 10 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 231829 | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF BB | Brushed Brass | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF C | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF BLK | Black | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 HOU BF C | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 257583 | Black | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FRZ BF C | Chrome | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| BQVEC BF C | Chromium | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| VT2 BF C | Chromium | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223206 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 85 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle option – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193805 X XXX | VARIOUS | ¾” BSP | 10 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223205 X XXX | VARIOUS | 3/4” BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided TPSiV lined hose assemblies Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Ranges of cylindrical or tubular expansion vessels with epoxy coated or uncoated steel bodies and either Butyl or EPDM membranes. Maximum working pressure of Tube models is 8.0 bar. All other models have a maximum working pressure of 10.0 bar. Maximum operating temperature 99°C.
Range of cylindrical expansion vessels with epoxy coated or uncoated steel bodies and Butyl membranes. Maximum working pressure 10.0 Bar (15.0 bar INOX PRO 0.16L). Maximum operating temperature 99.0°C.
Range of cylindrical expansion vessels with epoxy coated or uncoated steel bodies and Butyl membranes. Maximum working pressure 10.0 Bar Maximum operating temperature 99.0°C.
The products incorporate two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3), a pressure reducing valve adjustable between 1.0 bar and 3.0 bar (but pre-set at 2.5 bar for 523.815 model and 1.4 bar for the 523.816 model). The product incorporates a push type valve which allows water to flow when operated until the required pressure is achieved. There is a drain port below the push valve piston chamber. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum supply pressure 10.0 bar. Maximum operating temperature 80°C.
Range of filters with DZR brass bodies, stainless steel sieve. All models incorporate a drain tap and are supplied with a pressure gauge. Maximum working pressure 25.0 bar. Cold water use only.
A range of black polyethylene electrofusion fittings from DN 20 to DN 1200 for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. A range of black polyethylene butt-welded fittings from DE 20 to DE 1200 fittings for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. Maximum working pressure: 20.0 bar for SDR 9 Maximum working pressure: 16.0 bar for SDR 11 Maximum working pressure: 10.0 bar for SDR 17. For above and below ground and cold water use only.
Range of WC dual flush drop valve comprising of a plastic body, silicone seating washer and an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Push button pneumatically operated single flush WC drop valve, incorporating an internal overflow. For use with cold water only
Range of WC dual flush drop valves with an ABS body and silicone seal. The valves are operated via a push button or lever assembly for either full or reduced flush and incorporate an internal adjustable height overflow. Cold water use only.
Range electric, instantaneous, open outlet, mains water heaters. Maximum working pressure 6.6 bar. Maximum operating temperature 70 ˚C.
Electric instantaneous water heater with a plastic casing. Flow is controlled via a solenoid valve operated by an infrared sensor. Temperature is controlled by a dial on the front of the unit. The product incorporates a swivel arm outlet from the base. Maximum working pressure 3.0 bar. Maximum operating temperature 48˚C. Cold supply only.
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of water meters with blue epoxy power coated cast iron bodies, incorporating plastic turbines, NBR ‘O’-rings and gaskets. Maximum working pressure 16.0 bar. BS6920 50°C.
Range of in-line single jet water meters with brass bodies. Products incorporate plastic strainers. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 85.0°C.
Range of water meters with either cast iron (blue epoxy coated) or stainless-steel bodies, transducers and EPDM rubber O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 50.0°C.
Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201) and copper pipe. The products incorporate a drain off valve, plastic strainer and a single check valve cartridge however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of test port assemblies with DZR brass bodies. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C.
Range of electronic pump controllers with plastic bodies. Maximum working pressure 12.0 Bar. Cold water use only.
Range of spherical valves with a DZR brass body and lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of click type, pop-up wastes with metal bodies. Maximum operating temperature 60.0°C
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
'HYDRO MULTI-E' booster set range consisting of two to four electronically controlled pumps connected in parallel and mounted on a common base frame provided with all necessary fittings. The suction manifold incorporates an isolation valve fitted between it and the individual pumps, and a pressure switch with an isolation valve. The discharge manifold incorporates an isolation valve and a non-return valve (not suitable for backflow protection), which is fitted between it and the individual pumps, it also incorporates a combined isolation and drain valve. Maximum working pressure 16.0 bar. Cold water use only.
Dutypoint ‘VMV’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. VMV2, VMV3 and VMV4 pump sets are available with DN80 to DN150 manifolds depending on application. VMV5, VMV6, VMV7 and VMV8 pump sets are available with DN150 to DN200 manifolds, depending on application. The products incorporate spherical valves on both the suction and discharge manifolds, with expansion vessels, isolation valves, pressure gauges and transducers on the discharge manifolds only. Maximum working pressure 16.0 bar. Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of booster pumps with stainless steel bodies, impellers and non-return valves (not suitable for backflow protection) at the inlets. Maximum working pressure: 6.0 Bar. Cold water use only.
“TP/TPE series 100” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure: Cast iron models: 16.0 bar, Stainless steel models: 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.
“TPE 2 & TPE3 series” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.
Range shower outlets and accessories with brass bodies (various finishes). The inlet of the overhead shower outlet incorporates a stainless steel strainer. Maximum operating temperature 85°C. Open outlet use only.
Range of wall or ceiling mounted shower arms, (brass bodies - various finishes). Maximum operating temperature: 85°C
Range of shower handsets and connection hoses (brass bodies – various finishes). The inlet incorporates an approved check valve cartridge (with plastic flow regulator) however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HS170 XXX | Various | 1/2" BSP | bar | 85 °C | PPI | Body | No | Fixed Head, |
XXX Denotes the following: First, second & third XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VR1000 | Chrome | 15mm | 5 bar | 60 °C | Bristan | Body | No | Not applicable | Metal Backnuts | Not Applicable | Fixed Head, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 BIB C CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener | |
| VAL2 BIB C 6 CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener |
Draining tap with elbow shaped DZR brass body and a rising spindle headwork. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass (or DZR brass, see models) bodies and non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Drain off cock with a DZR brass body, non-rising spindle headwork and EPDM seals and washers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M0602 X XXX | various | 3/4" BSP | 10 bar bar | 85 °C | PPI | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MEFC-PAK | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Fixed Head | No | Self closing | Not Applicable | Not Applicable |
Range of black HDPE Pipe SDR 11 manufactured to ISO 4427 / DIN 8074 / EN12201. Maximum working pressure: 16 Bar. Maximum operating temperature: Cold water use only.
Range of multi-layered PP-R CT pipe (SDR 7.4) comprising of a green coloured PPR inner layer, translucent PPR/glass fibre middle layer and green coloured PPR outer layer. Not approved for use with any fittings. Maximum working pressure 23.4 bar. Cold water above ground use only.
Range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections. Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Nimbus Compact range of combination heat pump units with enamel lined tank and stainless-steel coil. Fitted with a magnesium anode, expansion vessel and T&P valve set at 7 bar & 95°C. supplied with an inlet control group consisting of a pressure reducing valve, strainer, pressure relief valve and single check valve, and a tundish. Max working pressure 6.0 Bar Max operating Temperature 80 °C
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Wall mounted, thermostatic blending valve (chrome plated brass body). Temperature is pre-set under fixed cap. The inlets incorporate an approved check valve cartridge, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. The product is supplied with plastic strainers and screwdriver operated spherical valves, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of below ground (screw down type) fire hydrants with coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A range of spring loaded, resilient trim non-return valves with EPDM seat, blue epoxy coated cast-iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of in-line adjustable pressure reducing valves with DZR brass bodies. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range 1.5 to 6.0 bar. Maximum operating temperature 65°C.
Range of in-line, adjustable, pressure reducing valves with DZR brass bodies. For use with copper pipe to EN 1057. Maximum inlet pressure 16.0 bar. Outlet pressure adjustable between 1.5 bar & 5.5 bar. Cold water use only.
Range of in-line manually adjustable pressure reducing valves with a DZR brass body (brushed chrome finish). Compression models are for use with coper pipe (manufactured to EN 1057). The MINIPRVG model is supplied with a gauge. Outlet pressure adjustable from 0.8 to 4.0 bar. Maximum inlet supply pressure 15.0 bar. Maximum operating temperature 80°C.
Range of in-line, manually adjustable pressure reducing valves with stainless-steel bodies and EPDM o-rings. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 25.0 Bar. Outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.
In-line, manually adjustable pressure reducing valves with DZR brass bodies. Maximum inlet supply pressure 16.0 Bar. Maximum outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with nickel plated DZR brass body. Maximum inlet supply pressure 25 bar. Maximum operating temperature 80°C
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Push fit versions only can also be used with both polybutylene pipe (manufactured to BS7291-2) and PEX pipe (manufactured to BS7291-3) Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome DZR brass bodies. Outlet pressure range: 1.0 - 6.0 bar. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pilot operated, pressure reducing valves epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, spherical valves and a needle valve. Outlet pressure setting is adjustable in the range of 1.0 bar to 12.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pre-set pressure relief valves with a DZR brass body, incorporating an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection for use with copper tube to BS EN 1057. Maximum working pressure: see models. Maximum operating temperature: 23.0°C
Range of latching (LV), proportional (PV), servo (SV), pilot (EV) solenoid valves with natural (appear white), plastic bodies. Pushfit models are for use with John Guest LLDPE and DMFIT LLDPE pipes. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. All valves have a maximum working pressure of 10.0 bar. The bodies of valves with a silicone diaphragm are marked with an ‘S’ at the end of the model, e.g. ‘EV118/AS’ and have a maximum operating temperature 85°C. Valves with an EPDM diaphragm are for cold water use only and do not include this ‘S’ marking.
A screwdriver operated spherical ball valve with brass body, chromium plated brass ball and EPDM O-ring. Maximum working pressure 5.5 bar. Maximum operating temperature 85oC.
Range of press fit spherical valves with chrome plated brass bodies, to be used with copper pipe EN1057. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with either brass (BFIVB-15, BFIVBL-15 & BFIVHPL-15 models) or nickel plated (BFIV-15, BFIVL-15,BFIVL-22 & BFSVB-15D models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screwdriver operated spherical valve with a brass & DZR brass body. The fitting incorporates two approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
Screwdriver operated spherical valve with a DZR brass body. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Spherical valves incorporating a drain port and two check valve cartridges (verified by test, suitable for backflow protection against fluid category 3) in a DZR brass body. Above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline or angled screwdriver or lever operated spherical valves with brass or chromium plated brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel plated brass bodies, chromium plated brass ball, PTFE seats and a drain valve. Maximum working pressure 25.0 Bar Maximum operating temperature 100.0°C
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass or brass bodies with chromium plated brass balls. Models incorporate lever or butterfly operating members. Maximum working pressure 10.0 Bar, 16 bar, 25 bar, 32 bar, 40 bar or 64 bar. Maximum operating temperature 100 °C.
Range of inline, angled or tee type spherical valves with brass (CP5R models), nickel plated brass (CP12 and CP02 models) or chromium plated brass (CP13 models) bodies, brass (10.20105.22X.CP5R-8510 and 10.20105.28X.CP5R-8510 models) or chromium plated brass (all other models) balls. The valves are either screwdriver, lever or butterfly handle operated (see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (10.60145.015.CP12-8510 and 10.61055.022.CP12-8510 models) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies and chrome plated brass ball. The compression and press-fit connections are for use with copper pipe (manufactured to EN1057). Jointing of the press-fit connection is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
`Water block` range of self-closing valves with either a natural (white), blue or grey plastic body and a gear driven volume-controlled operation device. The product incorporates a stainless-steel strainer. The product is designed to stop the flow of water once a preset value (in litres) has been reached. User intervention is then required to reset it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Electrolytic inline limescale reducer with a zinc plated brass body and a copper coil. Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Range of commercial and domestic ion exchange water softeners (salt regenerated). Operation is by an electronically controlled ion exchange resin filled plastic pressure vessel with integral salt cabinet (domestic models) or separate brine tank (commercial models). Maximum working pressure 8.0 bar. Cold water use only.
Continuous soft water, ion exchange, hydraulically driven water softener (salt regenerated) for domestic use, incorporating LLDPE tubing. Operation is by an ion exchange resin filed plastic pressure vessel, with integral salt cabinet and timer/manual regeneration control. The appliance incorporates single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature Cold water only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'EVER-BLACK 1'. Factory applied, black coloured, modified bitumen coating. Apply as per manufacturer's TDS TDS 'V1', dated '2023.03.05' and cure for dry/cure for 7 days@25°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M-106'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.
'M-133'. Grey coloured, compression moulded mechanical carbon graphite cylindrical component. For use with water up to 85°C.
'CER4'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Promag D - Flowtube'. Black coloured, injection moulded PA flowtube. For use with water up to 60°C.
'PolySTH Pushfit Fittings'. Injection moulded, polybutylene pushfit fittings available in white and grey colours. For use with water up to 85°C.
'PolySTH pipe'. Grey coloured, extruded multi-layered pipe consisting of a polybutylene inner and outer layer and a dark grey coloured EVOH middle barrier layer. For use with water up to 85°C.
‘PolySTH Pipe’. White coloured, extruded multi-layered pipe consisting of a polybutylene inner and outer layer and an EVOH middle barrier layer. For use with water up to 85°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
'TW03'. White coloured (translucent), injection moulded polyethylene thrust washer. For use with water up to 85°C.
'Hydropriv PE80 Pipe'. Black coloured (with blue external stripes) and blue coloured, extruded PE80 pipe. For use with water up to 23°C.
'DQ25G295H05 Water (Drain) Cap'. Cream coloured, injection moulded PPE drain cap component. For use with water up to 75°C.
'ECOSAN ML5 Pipe'. Extruded, multi-layered PP-RCT/PP-R/PP-R pipe which has a grey coloured inner layer and green coloured outer layer. The three intermediate layers are grey in colour. ‘ECOSAN SDR6 Pipe’. Extruded, single layered, green coloured (with red external stripe) PP-R pipe. Both pipes are for use with water up to 85°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'OLD ETP890 70N'. Black coloured, injection moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The E2WXX, E2BXX & E2GXX models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The E1WXX & EW1WXX models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. For use with cold water only
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Concealed 2-way or 3-way brass body diverter valve (see models) with or without shut off mechanism (see model) and various trim sets and operating members (see model). Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
Concealed self-cancelling control with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). (brass body) with a variety of operating member styles. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
