Atlantic Plastics Ltd Approvals


#2001058

Range of water meter manifolds with plastic bodies incorporating a drain off valve. Inlets incorporate a plastic strainer. Products also incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Cold water use only. Maximum working pressure 16.0 bar.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2001058
Expiry date:
31/01/2025
Note:
For above ground use only
Size:
15mm, 22mm compression (CU), 25mm spigot (PF) inlets to 15mm or 22mm compression (CU) outlets depending on model
Marking:
Talis logo and flow arrow on body
Installation Requirements:
R001
Model:
MA3261515AM Internal Meter Manifold 15 CU Inlet / Outlet MA3261522AM Internal Meter Manifold 15 CU Inlet / 22CU Outlet MA3262215AM Internal Meter Manifold 22 CU Inlet / 15CU Outlet MA3262222AM Internal Meter Manifold 22 CU Inlet / Outlet MA3262515AM Internal Meter Manifold 25 PF Inlet / 15CU Outlet MA3262522AM Internal Meter Manifold 25 PF Inlet / 22CU Outlet
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2008504

`Talbot, Atplas, Ebco & S Booth` ranges of injection moulded, acetal fittings. Talbot fittings available in: F10 black, F20 blue, F20 black, F10 natural, F20 natural & F10 & F20 black. Atplas fittings available in: F10 natural, F20 natural, F10 & F20 natural & F20 red. Ebco fittings available in: F10 natural, F20 natural, F20 blue, F20 red, F20 yellow & F20 black. S Booth fittings available in: F20 natural. For use with water up to 60°C.

Section:
5010 Acetal (Components)
WRAS Approval Number:
2008504
Expiry date:
31/08/2025
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2007358

Talbot range of self tapping ferrule straps with plastic bodies and a nitrile rubber seal. The product incorporates either a ¾” BSP (M) connection or a 25mm or 32mm push fit connection on the outlet from the cutting arm. For below ground use only. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1010 Ferrules
WRAS Approval Number:
2007358
Expiry date:
31/07/2025
Size:
See model
Marking:
Talis logo & size on strap. Ebco and date of manufacture MM/YY on metal banjo.
Installation Requirements:
R001 R008
Model:
Talbot Self Tapping Ferrule Strap PVC/PE x FI ¾”: E11912: 63mm PVC/PE x FI ¾ in. E11915: 90mm PVC/PE x FI ¾ in. E11918: 110mm PVC/PE x FI ¾ in. E11921: 125mm PVC/PE x FI ¾ in. Talbot Self Tapping Ferrule Strap PVC/PE x 25mm SDR11: E11910: 63mm PVC/PE x 25mm SDR11. E11913: 90mm PVC/PE x 25mm SDR11. E11916: 110mm PVC/PE x 25mm SDR11. E11919: 125mm PVC/PE x 25mm SDR11. Talbot Self Tapping Ferrule Strap PVC/PE x 32mm SDR11: E11911: 63mm PVC/PE x 32mm SDR11. E11914: 90mm PVC/PE x 32mm SDR11. E11917: 110mm PVC/PE x 32mm SDR11. E11920: 125mm PVC/PE x 32mm SDR11.
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2010347

Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. Maximum working pressure 10.0 bar. Cold water use only.

Section:
4001 Components and accessories
Section Subtitle:
Water meters.
WRAS Approval Number:
2010347
Expiry date:
31/10/2025
Note:
For above ground use only.
Size:
22mm compression,
Marking:
EBCO (brand of Talis UK) on body
Installation Requirements:
R001
Model:
BZMKS15 BZMKS22 BZMKC15 BXMKC22 BZMKP15 BZMKP22
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2102804

Range of water meter manifolds with plastic bodies. The inlets incorporate a spherical valve and a non-return valve (not suitable for back flow protection). Model MD1010101BM is for use with Irish Heavy gauge pipe manufactured to 15134/1977. All other models are for use with blue MDPE pipe manufactured to EN12201. Maximum working pressure 12.5 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2102804
Expiry date:
28/02/2026
Size:
see model
Marking:
Ebco and flow arrow on body.
Installation Requirements:
R001 R008
Model:
MB1012525BM: 25mm pushfit. MB1010202BM: 20mm pushfit. MB1010101BM: ½” Irish pushfit. MB1020303BM: ¾” BSP (F).
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2101327

Range of water meter manifolds with a plastic body and a spherical valve at the inlet. Models MB2012525DM & MB2010303DM incorporates two single check valve cartridges, all other models incorporate one single check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection Model MB201010BM is for use with Irish Heavy gauge pipe manufactured to 15134/1977. All other models are for use with blue MDPE pipe manufactured to EN12201. Maximum working pressure 12.5 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2101327
Expiry date:
31/01/2026
Size:
see mdoel
Marking:
Ebco and flow arrow on body
Installation Requirements:
R001 R008
Model:
MB2012525BM: 25mm pushfit. MB2012020BM: 20mm pushfit. MB2010101BM: ½” HG Irish compression. MB2010303BM: ¾” BSP (F). MB2011010BM: 25mm compression. MB2012525DM: 25mm pushfit. MB2010303DM: ¾” BSP (F).
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2110339

Range of meter boxes incorporating a plastic manifold arrangement consisting of a stop valve with non-rising spindle , check valve (however the complete assembly has not been tested to demonstrate it provides adequate backflow) and concentric meter port. Some models incorporate a drain off or blacking plug. Connections can be compression or push fit (see model). For use with PE8-0 pipe to BS EN 12201 and copper to EN 1057. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1525 Meter Chambers - Wall Mounted
WRAS Approval Number:
2110339
Expiry date:
31/10/2026
Size:
see model
Marking:
Talis logo, Talbot, flow arrow, pressure, inlet & outlet on body.
Installation Requirements:
R001 R430
Model:
Drain off model: WA3261515AM – 15mm x 15mm WA3261522AM – 15mm x 22mm WA3262215AM – 22mm x 15mm WA3262222AM – 22mm x 22mm WA3262515AM – 25mm p/f x 15mm WA3262522AM – 25mm p/f x 15mm Blanking plug model: WA3271515BM – 15mm x 15mm WA3271522BM – 15mm x 22mm WA3272215BM - 22mm x 15mm WA3272222BM – 22mm x 22mm WA3272515BM – 25mm p/f x 15mm WA3272522BM – 25mm p/f x 22mm
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2111325

Range of water meter manifolds (also known as double box valves) for use with MDPE pipe (manufactured to BS EN 12201). The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 16 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2111325
Expiry date:
30/11/2026
Size:
25mm & 32mm push-fit
Marking:
Talis, Talis logo & flow arrow on body.
Installation Requirements:
R001
Model:
‘Talbot Double Box Valves’: MB57425U Matrix Double Box Inlet 2 x 25mm PF, Outlet 2 x 25mm PF. MB5743225U Matrix Double Box Inlet x 32mm PF Tee, Outlet 2 x 25mm PF. MB5743232U Matrix Double Box inlet 1 x 32mm PF Tee, Outlet 2 x 32mm PF. MB57432U matrix Double Box Inlet 2 x 32mm PF, Outlet 2 x 32mm PF.
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2201344

Range of water meter manifolds (plastic body). Model WB31520CG incorporates a single check valve cartridge and model WB31520CGDCV two single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 16.0 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2201344
Expiry date:
31/01/2027
Size:
¾” BSP (F)
Marking:
Talis on base. Flow arrow on manifold box.
Installation Requirements:
R001 R008
Model:
Talbot Matrix: WB31520CG WB31520CGDCV
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval


#2203314

Range of water meter manifolds with gun metal bodies and ball valve with either a quarter turn stop valve or screw down stop valve. The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1510 Water Meter Manifolds
WRAS Approval Number:
2203314
Expiry date:
31/03/2027
Note:
R008 applies to te plastic cap
Size:
see model
Marking:
Ebco logo, flow arrow, Foundry I.D. (QL) & date of manufacturer (MM/YY) on body.
Installation Requirements:
R001 R008
Model:
1" BSP (M) x ¾” BSP (F) models: MB1030403BM MB1030403EM MANI0461V MANI0461VW MANI0461VMCP20 MVB0250MCP40 MVB0240 MVB0241 MVB0250 MVB0255 ¾ BSP (F) x ¾” BSP (F) models: MBB0460V MBB0470V MBB0461V MBB0481V MBB0040V MBB0060V MVB0210 MVB0200 MVB0220 ¾” BSP (M) x ¾” BSP (M) models: MVB0020 MVB0030 MVB0040 MVB0045 1" BSP (M) x 1” BSP (M) MVB0230
Approval Holder:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company
Manufacturer:
Atlantic Plastics Ltd
Company Name
Atlantic Plastics Ltd
Address
Coytraherne Close Brackla Bridgend
Postcode
CF31 2AX
Phone
01656 672637
General Email
rhodgkiss@atplas.co.uk

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 1 of 3

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.