Range of concealed ‘T’ type thermostatic blending valves (chromium plated DZR brass bodies). The inlets incorporate a stainless steel strainer and single check valve cartridge, however, the complete product has not been fully tested to demonstrates it provides backflow prevention. The inlets of models PEG402UA, PEG402UAX, TX402UA, TX402UAX incorporate spherical valves. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C

Section:

2010 Valves

Section Subtitle:

Blending, thermostatic.

WRAS Approval Number:

1907010

Expiry date:

31/07/2024

Size:

See model

Marking:

Model, Pegler (Brand of Alaberts) & on cap. Tectite & ‘P’ on body

Installation Requirements:

R001 R010 R040

Model:

15mm & 22mm compression: PEG402, PEG402UA & PEG402UAX. 15mm & 22mm pushfit: TX402, TX402UA & TX402UAX

Manufacturer:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

‘Ballorex’ range of regulating valves with brass bodies, PTFE sliding washer, EPDM rubber ‘O’-rings and two test ports. Models are available with different flow rates depending on variant. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.

Section:

2348 Valves

Section Subtitle:

Balancing.

WRAS Approval Number:

1909317

Expiry date:

30/09/2024

Size:

See model

Marking:

Ballorex on operating member.

Installation Requirements:

R001

Model:

900SUL / 15008 / 1/2“UL 900SL / 15006 / 1/2“SL 900SS / 15000 / 1/2“SS 900SH / 16404 / 1/2“SH 900SL / 15007 / 3/4”SL 900SS / 15001 / 3/4”SS 900SH / 16405 / 3/4”SH 900SS / 15002 / 1”SS 900SH / 15181 / 1”SH 900SH / 15003 / 1 1/4"SH 900SH / 15004 / 1 1/2"SH 900SH / 15005 / 2”SH Where UL = ultra low flow, SL = low flow, SS = standard flow, SH high flow.

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

‘Kuterlite 700` range of compression fittings with DZR brass bodies and copper compression rings for use with blue polyethylene pipe manufactured to EN12201. Maximum working pressure 12.0 bar. Cold water use only.

Section:

1120 Fittings for use with Tube and Pipe

Section Subtitle:

Compression, metal, for use with plastic tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

1909004

Expiry date:

30/09/2024

Size:

25mm.

Marking:

KUTERLITE-700, size & technical info on nut. CR on fittings body.

Installation Requirements:

R001

Model:

K716 male elbow: 67118 (25mm x ¾” BSP male). K711 male coupling: 67050 (25mm x ¾” BSP male). K717 female elbow: 67135 (25mm x ¾” BSP female). K711LB long male coupling: 67070 (25mm x ¾” male). K717W back plate elbow: 67171 (25mm x ¾” BSP female). K710 straight coupling: 67005 (25mm). K712 female coupling: 67079 (25mm x ¾” BSP female). K718 equal tee: 67169 (25mm). K710IM adaptor: 67044 (25mm x ¾”). K715 elbow: 67102 (25mm). K778B compression ring: 22360 (25mm). K77M copper liner: 22372 (25mm). K730 female tee: 67259 (25mm x 25mm x ½” BSP female). 67251 (25mm x 25mm x ¾” BSP female). K751 stop end: 67348 (25mm). K7242 blanking plug: 67366 (25mm). K778A compression nut: 22353 (25mm).

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

Range of servicing valves with lever and tee type (T suffix models) operating members, nickel-plated brass bodies (PS550/PS500T models) or DZR brass (PS 550DR/PS550DRT models), chromium plated brass ball and PTFE seats. The valves incorporate gunmetal bodied ‘X press’ pressfit end connections with EPDM ‘O’-rings for use with copper tube. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

1909905

Expiry date:

30/09/2024

Size:

See model.

Marking:

Size, PN, Pegler England (brand of Aalberts) on body. Pattern No. Pegler, logo (brand of Aalberts) on operating member. Xpress on end connections.

Installation Requirements:

R001

Model:

PS500 Lever operated Ball Valves with XPress Adapted Ends – ½” to 2”: PS500 - Product code: 242301: 15mm. PS500 - Product code: 242303: 22mm. PS500 - Product code: 242304: 28mm. PS500 - Product code: 242305: 35mm. PS500 - Product code: 242306: 42mm. PS500 - Product code: 242307: 54mm. PS500T Tee handle operated Ball Valves with XPress Adapted Ends – ½” to 1”: PS500T - Product code: 243301: 15mm. PS500T - Product code: 243303: 22mm. PS500T - Product code: 243304: 28mm. PS550DR DZR Lever operated Ball Valves with XPress Adapted Ends – ½” to 2”: PS550 - Product code: 245220: 15mm. PS550 - Product code: 245222: 22mm. PS550 - Product code: 245223: 28mm. PS550 - Product code: 245224: 35mm. PS550 - Product code: 245225: 42mm. PS550 - Product code: 245226: 54mm. PS550DRT Tee handle operated Ball Valves with XPress Adapted Ends ½” to 1”: PS550T - Product code: 245230: 15mm. PS550T - Product code: 245232: 22mm. PS550T - Product code: 245233: 28mm. PS550EL Extended Lever operated Ball Valves with XPress Adapted ends ½” to 2”: PS550EL - Product code: 245300: 15mm. PS550EL - Product code: 245302: 22mm. PS550EL - Product code: 245303: 28mm. PS550EL - Product code: 245304: 35mm. PS550EL - Product code: 245305: 42mm. PS550EL - Product code: 245306: 54mm.

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

‘ISR’ range of copper, DZR brass or gunmetal capillary, lead free solder ring and threaded fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum working temperatures 99°C.

Section:

1115 Fittings for use with Tube and Pipe

Section Subtitle:

Capillary, solder ring, lead free. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2010800

Expiry date:

31/10/2025

Size:

See model

Marking:

BSI Kitemark, size and Pegler logo (brand of Aalberts) on body

Installation Requirements:

R001

Model:

YP1 - Straight Coupling: copper x copper - 6mm - 67mm YP1 IM - Slip Adaptor Coupling: imperial copper x metric copper - ½" x 15mm - 1½" x 42mm YP1R - Reducing Straight Coupling: copper x copper 8mm x 6mm - 54mm x 42mm YP1 Slip - Slip Straight Coupling: copper x copper - 15mm, 22mm, 28mm YP2 - Straight Female Connector: copper x BSP: [Parallel Female Thread] 8mm x ¼" - 54mm x 2" YP2LC - Female reducing connector: [reduced BSP female end] - 15mm x ¼", 15mm x ⅜", 22mm x ½" YP2LI - Female reducing connector: [reduced copper end] - ¾" x 15mm YP3 - Straight male connector: [copper x BSP taper male thread] - 8mm x ¼" - 67mm x 2½" YP3LC - Male reducing connector: [reduced BSP male end] - 15mm x ¼" - 28mm x ¾" YP3LI - Male reducing connector: [reduced copper end] - 3/4" x 15mm, 1" x 22mm YP5 - Tank connector: copper x BSP [parallel male thread] - 15mm x ½" - 54mm x 2" YP5FC - Tank connector: copper x BSP [parallel male thread] - 15mm x ½", 22mm x ¾", 28mm x 1" YP6 - Reducer: [Larger end for insertion into fitting] - 8mm x 6mm - 67mm x 54mm YP7 - Female adaptor:[male copper for insertion into fitting x BSP parallel female thread] 15mm x ½" - 54mm x 2" YP8 - Male adaptor: [male copper for insertion into fitting x BSP taper male thread] - 15mm x ½" - 54mm x 2" YP9 - Adaptor: [imperial female copper x metric male copper] - ½" x 15mm - 2" x 54mm YP9B - Non-standard adaptor - ½" 17G x 15mm YP99 - Adaptor: [Metric or imperial female copper x male copper] - 15mm x ½" - 42mm x 1½" YP11 - Union Coupling: [copper x copper] - 15mm - 67mm YP12 - Elbow: [copper x copper] - 6mm - 67mm YP12R - Reducing Elbow: [copper x copper] - 22mm x 15mm, 28mm x 22mm YP12S - Street Elbow: [Female copper x Male copper] - 8mm - 42mm YP13 - Male Elbow: [copper x BSP taper male thread] - 15mm x ½" - 42mm x 1½" YP14 - Female Elbow: [copper x BSP parallel female thread] - 15mm x ½", 22mm x ¾", 28mm x 1" YP14LC - Reducing Female Elbow: [Reduced female end] - 22mm x ½" YP15 - Backplate Elbow: [copper x BSP parallel female thread] - 15mm x ½", 22mm x ¾" YP15LN - Backplate Elbow: [Extended nose and circular backplate] - 15mm x ½" YP18 - Slow Bend: [copper x copper] - 15mm, 22mm, 28mm YP20 - Return Bend: [copper x copper] - 15mm, 22mm, 28mm YP21 - Obtuse Elbow: [copper x copper] - 15mm - 67mm YP22 - Partial Crossover: [female copper x male copper] - 15mm, 22mm YP23 - Full Crossover: [copper x copper] - 15mm, 22mm YP24 - Equal Tee: [All ends for copper] - 6mm - 67mm YP24 Slip - Equal Tee, Slip pattern: [All ends for copper] - 15mm YP25 - Tee, Reduced Branch: [All ends for copper] - 22mm x 22mm x 10mm - 67mm x 67mm x 28mm YP26 - Tee, One End Reduced: [All ends for copper] - 22mm x 15mm x 22mm - 54mm x 42mm x 54mm YP27 - Tee, One End and Branch Reduced: [All ends for copper] - 22mm x 15mm x 15mm - 54mm x 42mm x 42mm YP28 - Tee, Both Ends Reduced: [All ends for copper] - 15mm x 15mm x 22mm - 35mm x 35mm x 42mm YP29 - Female Tee: [Copper end and Copper branch x reduced BSP parallel female end] - 15 x ½" x 15mm, 22 x ¾" x 22mm YP29R - Female Tee: [Copper end and Copper branch x reduced BSP parallel female end] - 22mm x ½" x 22mm, 28mm x ½" x 28mm, 35mm x ½" x 35mm YP30 - Female Tee: [Copper ends x BSP parallel female branch] - 15mm x 15mm x ½", 22mm x 22mm x ¾", 28mm x 28mm x 1" YP30BP - Backplate Tee: [Copper ends x BSP parallel female branch. Circular backplate] - 15mm x 15mm x ½" YP30R - Female Tee: [Copper ends x reduced BSP parallel female branch] 15mm x 15mm x ¼" - 42mm x 42mm x 1/2" YP37 - Sweep Tee, 90°: [All ends for copper] - 15mm, 22mm, 28mm YP37R - Sweep Tee, 90°: [Reduced branch] - 22mm x 22mm x 15mm, 28mm x 28mm x 15mm YP50 - Cross: [All ends for copper] - 15mm, 22mm YP61 - Stop End: [For use on copper tube] - 8mm - 54mm YP35 - Air Vent Tee: [YP37 Sweep Tee plus Air-Release Valve RV35] - 15mm RV35 - Air-Release Valve: [Male copper end suitable for use in any capillary socket] - 15mm YP62 - Tap Connector: [copper x BSP union nut. Spigot and washer joint] - 15mm x ½" - 22mm x ¾" YP63 - Bent Tap Connector: [copper x BSP union nut. Spigot and washer joint] - 15mm x ½" - 22mm x ¾" YP63L - Long Bent Tap Connector: [copper x BSP union nut. Spigot and washer joint] - 15mm x ½" YP64 - Bent union adaptor: [copper x BSP union nut] - 22mm x 1", 28mm x 1¼" YP65 - Bent male union connector: [copper x BSP taper male thread] - 15mm x ½" - 42mm x 1½" YP65R - Bent Boiler union: [copper x BSP taper male thread] - 22mm x 1" YP68 - Union adaptor: [copper x BSP union nut] - 15mm x ¾", 22mm x 1", 28mm x 1¼" YP68CL - Union adaptor: [copper x BSP union nut. Spigot and fibre washer joint] - 15mm x ¾", 22mm x 1", 28mm x 1¼" YP68CLDZR - Union adaptor: [copper x BSP union nut. Spigot and fibre washer joint] with DZR nuts - 15mm x ¾" YP68FF - Flat Faced Union adaptor: [copper x BSP union nut] Suitable for use with water meters. - 15mm x ¾", 22mm x 1" YP68M - Meter union connector: [copper x BSP union nut] Suitable for use with water meters. - 22mm x ¾" YP69 - Straight male union connector: [copper x BSP taper male thread] - 15mm x ½" - 54mm x 2" YP69DP - Straight male union connector: with 104mm dip pipe. - 22mm x ¾" YP69F - Straight female union connector: [copper x BSP parallel female thread] - 15mm x ½" - 54mm x 2" YP69P - Straight male union connector: [copper x BSP parallel male thread] - 15mm x ½", 22mm x ¾", 28mm x 1", 67mm x 2½" YP70 - Male nipple: [union thread x BSP taper male thread] - ½" x ⅜", ¾" x ½", 1" x ¾", 1¼" x 1" YP70P - Male nipple: [union thread x BSP taper male thread] For use with YP64 and YP68 - ¾" x ½", 1" x ¾" YP71 - Male nipple: [union thread x BSP taper male thread] equal ends. - ½" , ¾", 1" YP72 - Female nipple: [union thread x BSP parallel female thread] - ¾" x ½" - 2½" x 2" YP115 - Extension nipple: [Used to give extra length to female ends on YP14, YP15, YP30] - ½" - ¾"

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

Range of servicing valves with lever and tee type (T suffix model) operating members, nickel-plated brass bodies (PT550 models) or DZR brass (PT550DR/PT550DRT models), chromium plated brass ball and PTFE seats. The valves incorporate Tectite Pro DZR brass push-fit fittings for use with copper tube (manufactured to BS 2871). Maximum working pressures and operating temperatures: 15mm - 28mm: 20.0 bar @ 30°C, 16.0 bar @ 65°C & 10.0 bar 100°C. 32mm - 54mm: 16.0 @ 30°C, 10.0 bar @ 65°C & 6.0 bar @ 90°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

2003900

Expiry date:

31/03/2025

Size:

See model.

Marking:

Size, PN, Pegler England (brand of Aalberts) on body. Pattern No. Pegler, Pegler logo (brand of Alberts) on lever operating member. Tectite, size & CR on end connections.

Installation Requirements:

R001

Model:

PT500 Lever operated Ball Valves with Tectite Adapted Ends – ½” to 2”: PT500 - Product code: 242350: 15mm. PT500 - Product code: 242352: 22mm. PT500 - Product code: 242353: 28mm. PT500 - Product code: 242354: 35mm. PT500 - Product code: 242355: 42mm. PT500 - Product code: 242356: 54mm. PT550DR DZR Lever operated Ball Valves with Tectite Adapted Ends – ½” to 2”: PT550 - Product code: 245240: 15mm. PT550 - Product code: 245241: 18mm. PT550 - Product code: 245242: 22mm. PT550 - Product code: 245243: 28mm. PT550 - Product code: 245244: 35mm. PT550 - Product code: 245245: 42mm. PT550 - Product code: 245246: 54mm. PT550DRT Tee handle operated Ball Valves with XPress Adapted Ends ½” to ¾”: PT550T - Product code: 245250: 15mm. PT550T - Product code: 245252: 22mm. PT550EL Extended Lever operated Ball Valves with Tectite Adapted ends ½” to 2”: PT550EL - Product code: 245290: 15mm. PT550EL - Product code: 245291: 22mm. PT550EL - Product code: 245292: 28mm. PT550EL - Product code: 245293: 35mm. PT550EL - Product code: 245294: 42mm. PT550EL - Product code: 245295: 54mm.

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

Range of servicing valves with lever operating members, DZR brass bodies, chromium plated brass ball and PTFE seats. The valves incorporate ‘VSH SudoPress’ copper press-fit fittings with EPDM ‘O’ rings for use with copper pipe. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

2003901

Expiry date:

31/03/2025

Size:

See model.

Marking:

Size, PN, Pegler England (brand of Aalberts) on body. Pattern No. Pegler, (brand of Aalberts) Pegler logo on lever operating member. SudoPress on end connections.

Installation Requirements:

R001

Model:

PSV 550DR DZR Lever operated Ball Valves with VSH SudoPress Adapted Ends – ½” to 2”: PSV 550 - Product code: 250100: 15mm. PSV 550 - Product code: 250102: 22mm. PSV 550 - Product code: 250103: 28mm. PSV 550 - Product code: 250104: 35mm. PSV 550 - Product code: 250105: 42mm. PSV 550 - Product code: 250106: 54mm. PSV 550 EL DR Extended Lever operated Ball Valves with VSH SudoPress Adapted Ends – ½” to 2”: PSV EL 550 - Product code: 250150: 15mm. PSV EL 550 - Product code: 250152: 22mm. PSV EL 550 - Product code: 250153: 28mm. PSV EL 550 - Product code: 250154: 35mm. PSV EL 550 - Product code: 250155: 42mm. PSV EL 550 - Product code: 250156: 54mm.

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

In-line and angled screwdriver operated spherical valves with DZR brass or chromium plated DZR brass bodies, brass ball, EPDM ‘O’-rings and PTFE or EPDM seat. . Some models incorporate a stainless steel filter. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

2001373

Expiry date:

31/01/2025

Size:

See model.

Marking:

Ballofix, size, pressure and DR on the body

Installation Requirements:

R001

Model:

13108 BALLOFIX 15x15MM 13133 BALLOFIX 1/2" SWIVEL NUT x 15MM, SC 13135 BALLOFIX 1/2" SWIVEL NUT x 15MM WITH HANDLE, SC 13148 BALLOFIX F/M 1/4 X 1/4 13151 BALLOFIX F/M 1/4 X 1/4 SC 13161 BALLOFIX F/F 1/4 X 1/4 SC 13166 BALLOFIX F/M 3/8 X 3/8 13186 BALLOFIX F/F 3/8 X 3/8 13189 BALLOFIX F/F 3/8 X 3/8 SC 13226 BALLOFIX F/M 1/2 X 1/2 W/HDL 13228 BALLOFIX F/M 1/2 X 1/2 SC W/HDL 13236 BALLOFIX F/COMP 1/2 X 15 SC W/HDL 13311 BALLOFIX 1/2x15MM M 13321 BALLOFIX 15MM X 15MM 13324 BALLOFIX ANGLE COMP/COMP 15 X 15 SC 13356 BALLOFIX M/M 1/2 X 1/2 SC 13374 BALLOFIX F/M 3/4 X 3/4 13377 BALLOFIX F/M 3/4 X 3/4 SC 13445 BALLOFIX F/M 1 X 1 13531 BALLOFIX F/COMP 1/2 X 15 SC 13532 BALLOFIX F/F 1/2 X 1/2 13532 BALLOFIX F/F 1/2 X 1/2 13533 BALLOFIX F/F 1/2 X 1/2 SC W/HDL 13535 BALLOFIX F/F 1/2 X 1/2 SC 13538 BALLOFIX F/M 1/2 X 1/2 13539 BALLOFIX F/M 1/2 X 1/2 SC 13540 BALLOFIX COMPRESSION 15MM 13541 BALLOFIX COMPRESSION 15MM WITH HANDLE 13543 BALLOFIX COMP/COMP 15 X 15 SC 13544 BALLOFIX COMPRESSION 15MM WITH HANDLE, SC 13545 BALLOFIX COMPRESSION 15MM WITH CROME HANDLE, SC 13559 BALLOFIX 3/4" F/F BRASS 13560 BALLOFIX F/F 3/4 X 3/4 SC 13563 BALLOFIX COMP/COMP 22 X 22 13564 BALLOFIX COMP/COMP 22 X 22 SC 13573 BALLOFIX F/F 1 X 1 13574 BALLOFIX F/F 1 X 1 SC 13575 BALLOFIX COMP/COMP 28 X 28 13576 BALLOFIX COMP/COMP 28 X 28 SC 13658 BALLOFIX 1/2" SWIVEL NUT x 15MM 13143 BALLOFIX ANGLE SWIVEL NUT 1/2" SC 13523 BALLOFIX ANGLE SWIVEL NUT 1/2" 13060 BALLOFIX PRESS/PRESS 15 X 15 SC 13061 BALLOFIX PRESS/PRESS 22 X 22 SC W/HDL 13260 BALLOFIX M/PRESS 1/2 X 15 SC W/HDL 13073 BALLOFIX PUSH/PUSH 15 X 15 SC 13081 BALLOFIX PUSH/PUSH 15 X 15 SC W/HDL 13081 BALLOFIX PUSH/PUSH 15 X 15 SC W/HDL 13263 BALLOFIX PUSH/MALE 15 X 1/2 SC 13304 BALLOFIX 15MM 13521 BALLOFIX 15X15MM WITH NON RETURN VALVE

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

Range of gate valves with DZR brass bodies and brass wedge. Valves are operated via a non-rising spindle headwork. Maximum operating pressure 20.0 Bar. Maximum operating temperature 100°C.

Section:

2290 Valves

Section Subtitle:

Stop, gate, metal.

WRAS Approval Number:

2102800

Expiry date:

28/02/2026

Size:

See model

Marking:

Pegler England (brand of Aalberts) , size, PN & BR on body.

Installation Requirements:

R001

Model:

½” – 4” 1068 BS 5154 PN20 full way gate valve with handwheel. 203007, 203008, 203009, 203010, 203011, 203013, 203014 & 203015 ½” – 2” 1068LS BS 5154 PN20 full way gate valve with lockshield. 203067, 203068, 203069, 203070, 203071, 203072

Manufacturer:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company

Range of latching and non-latching normally closed solenoid valves with either brass or stainless-steel bodies. Please refer to model for maximum working pressure. Maximum operating temperature 85°C.

Section:

2230 Valves

Section Subtitle:

Solenoid, metal.

WRAS Approval Number:

2007078

Expiry date:

31/07/2025

Size:

See model

Marking:

PEGLER (brand of Aalberts) & PRODUCT INFORMATION ON BODY

Installation Requirements:

R001

Model:

12900, 12901, 12902, 12903, 12904, 12905, 12906, 12907, 12908, 12910, 12911, 12912, 12913, 12914, 12915, 12916 & 12917 SOLENOID VALVES Maximum working pressure 16.0 bar: 1/2’’ BSP (F) (12900, 12901, 12902) Maximum working pressure 12.0 bar: 3/4’’ BSP (F) (12903, 12904, 12905) 1’’ BSP (F) (12906, 12907, 12908) Maximum working pressure 10.0 bar: 1 1/4’’ BSP (F) (12909, 12910, 12911) 1 1/2’’ BSP (F) (12912, 12913, 12914) 2’’ BSP (F) (12915, 12916, 12917)

Factor:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Phone

01302 560560

View All Listings by this Company