Section Code 1530 :
Back To Directory SectionsRange of servicing valves with plastic bodies incorporating quarter turn non-rising spindle headworks, nitrile seals & `O`-rings. Maximum working pressure 10.0 Bar. Cold water use only.
ecoBETA retrofit insert with an ABS body for use with siphons to reduce flush volumes. Cold water use only.
Talbot range of gunmetal screw down servicing valves for use with MDPE80 pipes (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Manually operated blending valve incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 75°C
Corzan PVC-C range of plastic pipe and fittings intended for jointing using solvent cement. Maximum working pressures: 16mm-110mm = 16.0 bar, 160mm = 10.0 bar. Cold water use only.
Range of Tanktronic monitoring kits comprising of a main control unit, vent box and single or double stainless steel sensors. The kits are supplied with either a three or five metre cable. Cold water use only.
Range of water drainage systems, mains and battery operated, incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 1.0 bar. Cold water use only.
Range of measurement devices with copper alloy bodies and EPDM o-rings. Models beginning with 1384G & 1386G models measure flow and temperature. Models beginning with 6280G measures temperature only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted shower (column) units incorporating a solenoid valve controlling the flow to a fixed overhead shower outlet using an infra-red sensor. Model TFP3005IR also incorporates a thermostatic mixer which can be set manually to control the temperature. Inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Each model has a plastic flow regulator, within the shower outlet of the TFP3004IR model and inline after the solenoid of the TFP3005IR model. All models are supplied with servicing valves to be installed on each of the inlet connections. Maximum working pressure 5.0 Bar. Maximum operating temperature 65°C.
Two spring loaded resilient trim in-line approved check valve cartridges housed in a plastic body with Push Fit End Connections (however, the complete product has not been fully tested to demonstrate it provides backflow protection) The assembly also incorporates a drain port located between the cartridges. For use with copper pipe (manufactured to EN 1057), PEX pipe (manufactured to BS7291-3) and John Guest LLDPE tubing. Maximum working pressure 12.5 bar. Maximum operating temperature 65°C.
Range of expansion bellows with stainless steel bodies. Maximum working pressure 10.0 bar (QSL-Type ABS). Maximum working pressure 16.0 bar (QSL-Type AB, QSL-Type PB). Maximum operating temperature 99°C
Two spring loaded resilient trim in-line approved check valve cartridges housed in an acetal body (however, the complete product has not been fully tested to demonstrate it provides backflow protection) The assembly also incorporates a drain port located between the cartridges. For use with copper and polybutylene pipe (manufactured to BS EN ISO 15875). Maximum working pressure 10.0 Bar. Cold water use only.
Wall mounted, shower, flow control valve (either stainless steel or brass bodies in a variety of finishes) incorporating a quarter turn ceramic disc headwork with a single lever operating member. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Two spring loaded resilient trim in-line approved check valve cartridges housed in an acetal body (however, the complete product has not been fully tested to demonstrate it provides backflow protection) The assembly also incorporates a drain port located between the cartridges. For use with copper and polybutylene pipe (manufactured to BS EN ISO 15875). Maximum working pressure 10.0 bar. Cold water use only.
Threaded adapter with plastic body and nitrile ‘O’-ring. Maximum working pressure 12.5 bar. Cold water use only.
Proportional modulation valve used to prioritise flow depending on requirement with a brass body and EPDM membrane. Maximum working pressure 10.0 bar secondary & 6.0 bar primary. Maximum operating temperature 99°C.
Range of thermostatic elements with copper shell and Silicone smart cover. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
‘FROSTI®-PLUS’ through wall externally mounted angled valve with gunmetal body and non-rising headworks. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of air break to drain assemblies with brass bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of aerators with plastic bodies and filter screens. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Range of in-line thermometer holder fittings with chrome plated brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Range of differential or relative pressure sensors with stainless steel bodies and EPDM ‘O’-rings. The DPI V.2 model consists of a sensor and fitting for a capillary tube which is used for measuring the differential pressure between either sides of the sensor. Maximum working pressure 40.0 Bar. Maximum operating temperature 100°C.
Range of expansion bellows with stainless steel bodies. Maximum working pressure 10.0 bar (EMFLEX-BATN-W). Maximum working pressure 16.0 bar EMFLEX-BAFN-W, EMFLEX-BFCN-W). Maximum operating temperature 99°C
Range of flow restrictors with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 60°C.
‘T-Plus’ range of couplings for use with copper or thin wall stainless steel tube and pipe, intended for the branching of existing pipework. The product utilises a live charge that is activated by striking a pin, which in turn pushes a plunger to cut a section of pipe, retaining it internally. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Combined bath filler and overflow waste assembly. Maximum operating temperature 65°C
Automated valve with a chromium plated brass body. The valve is designed to close in the event of excess flow of water to stop the flow in the event of a leak. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass bodied temperature sensors for use with electronic boiler controls. Maximum rating temperature 100°C.
`Ambi-Carb` range of carbonator units incorporating a pump on the inlet. All units incorporate a carbonated circuit where the flow is controlled by a solenoid valve. All units incorporate a double check valve assembly, verified by test (suitable for back flow protection against fluid category 3) directly before the carbonator bowl. Maximum working pressure 3.5 Bar. Cold water use only.
Range of flow limiters comprising of a bronze body incorporating a plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
8NL16G-12 model: handwheel operated rising spindle servicing valves with NBR ‘O’-ring and seat. 8NL16G-14 model: lever operated spherical valve with chromium plated brass bodies and balls, PTFE seat and NBR ‘O’-rings. 8NL16G-15 model: screwdriver operated rising spindle servicing valves with NBR ‘O’-ring and seat. Maximum working pressure 10.0 bar. Maximum operating temperature 75°C.
‘Shepherds crook’ assemblies consisting of a riser tube, shower hose and handset. Maximum operating temperature 41°C.
Opella black elbow adaptor with plastic body incorporating an EPDM seal. Maximum operating pressure 10.0 bar. Cold water use only.
Range of in-line flow sensors with plastic bodies and a plastic impeller case. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of tee pieces with brass bodies. Models 0912/15CVCC & 0912/CVCC incorporates a non-return valve (not suitable for backflow prevention) and stainless steel retaining clip. Maximum working pressure 10.0 bar. Maximum operating temperature 85˚C.
Range of in line regulating and commissioning valves with brass bodies, brass plugs and EPDM ‘O’-rings. The valves incorporate a non-rising spindle headwork with hand wheel operating member regulating the flow and isolation function. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Shower filter connection for use with shower outlets having polypropylene bodies and EPDM gaskets. Maximum operating temperature 70°C.
Range of plastic bodied chrome plated shower outlets, tap outlets and in-line filters, all incorporating a polyethylene fibre membrane. Maximum operating temperature 70°C.
Range of pressure sensors for booster pumps with stainless steel bodies. Models consists of a sensor and male threaded end. Maximum working pressure: 35CP11-15165006YS00H2EC & 35CP11-38165006YS00H2EC = 6.0 bar. 35CP11-16165109YS00H2EC = 9.0 bar. 35CP11-11165010YS00H2EC & 35CP11-36165010YS00H2EC = 10.0 bar. 35CP11-12165016YS00H2EC & 35CP11-37165016YS00H2EC = 16.0 bar. 35CP11-18165025YS00H2EC & 35CP11-39165025YS00H2EC = 25.0 bar. 35CP11-19165040YS00H2EC & 35CP11-40165040YS00H2EC = 40.0 bar. Maximum operating temperature 90°C.
Elbow fitting manufactured from DZR brass. Maximum working pressure 10 bar and maximum operating temperature 85°C.
Range of single spring loaded resilient trim approved check valve cartridges housed in a plastic body (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Product incorporates push fit end connections and incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Cold water use only.
Range of flow sensors with plastic bodies and rotors. Maximum working pressure 17.2 bar. Maximum operating temperature 80°C.
`Non-Freeze` water point for through wall mounting with wall box in a cast gunmetal body incorporating brass rising spindle headworks. The products are supplied with closing key. Maximum working pressure 10bar, Cold water use only.
Flow regulator with a white plastic body and with a stainless-steel spring and internal ring. Maximum working pressure 10.3 bar. Maximum operating temperature 26.6°C
Range of flow regulators with plastic bodies with a stainless-steel spring and internal ring. For insertion for a specifically dimensioned pipe. Maximum operating temperature 26.66°C.
‘Moneca Smart’ water hydrant and meter assembly, incorporating epoxy coated ductile iron fittings and spools, housed within a plastic outer casing. The flow is controlled via solenoid valve which is actuated using the card reader. The outlet mechanism incorporates a non-return valve (not suitable for backflow protection). Maximum working pressure 10.0 Bar. Cold water use only.
Flow regulators with brass body and stainless-steel spring and internal ring. Maximum working pressure 10.3 bar. Maximum operating temperature 26.6°C
Range of pressure sensors for booster pumps with stainless steel bodies. Models consists of a sensor and male threaded end. Maximum working pressure: 2549431 = 6.0 bar, 2549430 = 9.0 bar, 2549432 = 10.0 bar, 2549433 = 16.0 bar, 2549434 = 25.0 bar, 2549435 = 40.0 bar. Maximum operating temperature 90°C.
‘DM900’ range of flow measuring devises with stainless steel bodies incorporating two test points (one for hot and one for cold) with ¼” BSP (M) threads. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Brass bodied pressure gauge with copper bourbon tube. Maximum working pressure 4.0 bar. Maximum operating temperature 60°C.
‘Herz CTC 4011’ range of thermostatically operated flow control valves with DZR brass bodies and EPDM ‘O’ rings. The products are intended to control circulation in hot water systems. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of ‘heat battery’ units incorporating a phase change material which can be heated via an external source or integrated heating element depending on model variant. This allows instantaneous hot water on demand and/or central heating depending on the model via an integrated heat exchanger. Some models incorporate an additional back up electrical heating element. Maximum working pressure 10.0 bar (Secondary circuit and Primary circuit - applicable models). Maximum working temperature 80°C
‘Hattersley M2000’ range of flow measuring devises with stainless steel bodies incorporating two test points (one for hot and one for cold) with ¼” BSP (M) threads. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Surestop electronically actuated control module with plastic body. The product is intended to be used with and operate ‘Surestop Remote’ valves (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
Range of screw down servicing valves with brass bodies. The 05 380 06 99 model has a chrome plated brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘Tanktronic‘ range of water level monitoring kits comprising of a main control unit, vent box and single or double stainless steel sensors. Cold water use only.
Range of bypass valve assemblies with DZR brass bodies, incorporating EPDM `O` rings and lever operated spherical valves. Between the two circuits a double check valve (suitable for backflow prevention against Fluid Category 3) is installed. Maximum working pressure 10.0 bar. Cold water supply only.
Range of in line regulating valves DZR brass bodies and EPDM ‘O’ rings. The valves incorporate a non-rising spindle headwork, with hand wheel operating member, regulating the flow. Maximum working pressure 20.0 bar. Maximum operating temperature 95°C.
Range of extension pieces with either a brass or chrome plated brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Spherical isolation valve with brass body and chromium plated brass ball. Valve incorporates a brass drain valve with NBR seat washer. Maximum working pressure 10.0 bar. Cold water use only.
Range of submersible pressure sensors and hydrostatic transmitters with ceramic sensing elements, stainless steel bodies and polyethylene connection cables (supplied in lengths up to 1000m). Cold water use only.
Range of DZR brass bodied temperature sensors with EPDM ‘O’-rings (STDW15 model only). Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
Range of ‘Surestop Remote Switch’ servicing valves with plastic bodies and EPDM ‘O’-rings. Flow is controlled via a remote switch. The inlet incorporates a plastic strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed rough-in sets with brass bodies, intended for use in conjunction with trim and finish sets. The products incorporate elbow fittings. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
'PUREOX 3500’ chlorine dioxide dosing system with PVC-u pipework and EPDM O-rings. Maximum working pressure 3.0 bar. For cold water use only.
Range of shower projection arms with chrome plated brass bodies. Maximum operating temperature 65ºC.
Range of pressure sensors with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Thermowatt immersion heaters with either copper, stainless steel, alloy or titanium heating elements and black EPDM O-Rings. Maximum operating temperature 99˚C.
Range of pressure transmitters gauge pressure measurement devices and differential pressure measurement devices with either stainless steel or Hastelloy or Monel bodies. Maximum working pressure 66.0 bar. Maximum operating temperature 85°C.
‘Secuflex’ range of rim mounted, concealed pull-out shower sets, consisting of a metal interlocked shower hose, brass outlet connector and a stainless steel braided, silicone lined flexible connecting hose assembly. The concealed hose connection incorporates an approved single check valve cartridge; however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Maximum operating temperature 70°C.
Water hammer arrester (chromium plated brass), incorporating EPDM seals. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of brass bodied differential bypass valves incorporating a spring-loaded adjustment facility. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Click type pop-up waste with a plastic body. The products are supplied with a plastic backnut.
Fully automatic electronic anti-leakage system. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Flow sensor with plastic body and turbine. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of pressure sensors with stainless steel bodies, EPDM ‘O’-rings and ceramic diaphragms. Rectus 21 model has a maximum working pressure of 20.0 bar. ¼” BSP (M) model has a maximum working pressure of 50.0 bar. Cold water use only. From November 2019 Maximum operating temperature 85°C
Range of flow sensors. Maximum working pressure 12.0 bar. Maximum operating temperature 99˚C
Silver anode intended to be used within an ion generating water conditioner. Maximum operating temperature 40°C.
`Prox and Wave` ranges of sensor operated flow control devices incorporating solenoid valves with acetal bodies, EPDM rubber diaphragms, stainless steel pins and plungers. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of test port assemblies with DZR brass bodies. Maximum working pressure 25.0 Bar, Maximum operating temperature 100°C
Range of electronically controlled, wall mounted, shower flow control devices with chromium plated brass bodies. The flow is controlled by a solenoid valve. The inlets of the products incorporate a stainless-steel strainer. Neptune 1011 is infrared operated. Perfect Time SH 1011 is touch operated. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Plastic turbine for insertion into specifically dimensioned flow meters. Maximum operating temperature 85°C. Open outlet use only.
Appliance inlet group assembly comprising a Y-pattern strainer, two, nickel plated brass adaptors, double check valve assembly (DZR brass, chrome plated body – verified by test, suitable for backflow protection against Fluid Category 3), dual layer PVC supply hose and a solenoid incorporating a strainer. Two of the solenoid outlets incorporate a plastic flow regulator. Maximum working pressure 7.0 bar. Maximum operating temperature 60°C.
Flow restriction valve having a brass body and FKM rubber seal. Maximum working pressure 35.0 bar. Maximum operating temperature 85°C
Thermostatic circulation valve incorporating a DZR brass body and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of black (metric) or grey (imperial) flow regulating valves (plastic bodies) with rising spindle headworks & EPDM ‘O’-rings. For use with LLDPE pipe. Maximum working pressure 10.0 bar. Cold water use only.
Range of in line regulating valves with brass bodies, EPDM `O` rings. The valves incorporate a non-rising spindle headwork for temperature regulation. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of vertical lift valves with bronze bodies and metal to metal seals Maximum working pressure 32 bar. Maximum operating temperature 85°C
Range of below ground hose union taps within a chamber incorporating a brass spherical valves, hose connector and MDPE couplings. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C
Wall brackets with brass bodies (chromium plated) and EPDM o-rings. Maximum working temperature 85°C
Pressure boosting system suitable for direct connection to a wholesome water supply. The product discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a quadruple layered flexible inlet hose consisting of a black coloured TPE inner layer, PVC middle layer, braided PE third layer and white PVC outer layer. The water downstream of the AB airgap assembly is not for wholesome use. Maximum working pressure 10.0 bar. Cold water use only.
Range of combined bath filler, waste and overflow assemblies in various finishes. Maximum operating temperature 60ºC.
In-line plastic flow regulator housed within a brass body incorporating EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
In-line plastic flow regulator housed within a brass body (chrome plated) incorporating a plastic strainer and an EPDM ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Thermostatic circulation valve incorporating a DZR brass body and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Raindance Select E range of wall ceiling or wall mounted shower outlets having brass bodies. Maximum operating temperature 70°C
Range of click type, pop-up wastes with metal bodies and rubber seals. Supplied with brass backnuts. Maximum operating temperature 65°C
Range of flow meters with plastic bodies and EPDM ‘O’-rings. Maximum working pressure 8.0 Bar. Cold water use only.
Range of tempering valves with brass bodies incorporating a thermostatic element. Each inlet comprises of a 90° elbow incorporate spherical valve and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Electronically controlled advanced flow control pilot valve assembly with stainless steel body and EPDM diaphragm. Maximum working pressure 16.0 bar. Cold water use only
Chromium plated click type pop up waste with metal body and rubber seals. Supplied with a metal backnut.
Range of flow regulators, aerators and flow straighteners with plastic bodies, EPDM O-rings. Models JM030503 & JM030002 incorperate a stainless steel mesh. Maximum operating temperature 60°C.
Range of elbows (brass body with various finishes) and shower hoses. The inlet of the shower hose incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Flow restriction block having a stainless-steel body and integral stainless-steel filter, EPDM ‘O’-rings and NBR washers. Maximum working pressure 16.0 Bar. Cold water use only.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Ranges of sensor operated flow control devices incorporating solenoid valves with acetal bodies, EPDM rubber diaphragms, stainless steel pins and plungers. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of metering stations with DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
‘Promag D’ Range of flow meters with nylon flow tube liners, stainless steel flange connectors and EPDM ‘O’ - rings. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Angled valve with a (chrome plated) brass body incorporating a rising spindle that controls the flow. Maximum working pressure 10.0 bar. Cold water use only.
Continuous circulation valve (brass body) incorporating a lever operated spherical valve and a port with a plastic plug. Maximum working pressure 10.0 bar. Maximum operating temperature 30°C.
Range of wall mounted bath spouts having chromium plated brass bodies with plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of stainless steel pipe expansion joints incorporating flanged end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of stainless-steel bellows with screwed ends. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of spout outlets with brass bodies (chrome plated or unlacquered brass), incorporating a plastic aerator and NBR ‘O’-rings. Maximum operating temperature 60°C.
Direct coupler (brass with a range of finishes) incorporating EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Brass adaptor for flexible tail connectors. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall mounted shower outlet elbow (various finishes) and shower handset holder, incorporating EPDM ‘O’-rings. Maximum operating temperature 65°C.
Range of pressure level transmitters with stainless steel bodies and an EPDM ‘O’-ring. Maximum working pressure: Type 711 - 0.1bar, 0.2bar, 0.3bar, 0.4bar, 0.5bar, 0.6bar, 1.0bar, 2.0bar, 4.0bar, 6.0bar, 10.0bar and 16.0bar. Type 712 - 0.3bar, 1.0bar, 1.6bar, 2.5bar, 1.4bar, 2.0bar and 3.0bar. Type 713 - 0.6bar, 1.0bar, 1.6bar, 2.5bar, 4.0bar, 6.0bar, 10.0bar and 16.0bar. Maximum operating temperature 80°C (Type 711). Maximum operating temperature 85°C (Type 712 & 713).
Digital, plastic in-line water powered shower meter. Maximum working pressure 3.0 bar. Maximum operating temperature 85°C.
Top entry compression cylinder flange with DZR brass body and copper anti-aeration dip tube. Maximum working pressure 4.0 bar. Maximum operating temperature 60°C.
Range of flow sensors with plastic bodies and plastic turbines. Maximum operating temperature 65°C.
Range of pressure transmitters with stainless steel bodies and EPDM ‘O’-rings. Maximum working pressures: 520 XXX range 100.0 bar, 522 XXX range & 540 XXX range 60.0 bar. Maximum operating temperature 520 XXX & 522 XXX range 99°C & 540 XXX range 80°C.
Crane brass pressure test point. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Hattersley brass pressure test point. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Cart’ range of plastic flow regulators within a plastic housing and either silicone, EPDM or NBR sealing gaskets and optional stainless steel filter. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall plate elbow (105° angle) with a brass body. Maximum operating temperature 100°C
Manifold with a brass body and 5 outlets. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
Range of ‘heat battery’ units incorporating a phase change material which can be heated via an external source or integrated heating element depending on model variant. This allows instantaneous hot water on demand and/or central heating depending on the model via an integrated heat exchanger. Some models incorporate an additional back up electrical heating element. Maximum working pressure 10.0 bar (Secondary circuit and Primary circuit - applicable models). Maximum working temperature 80°C
Range of stainless steel diaphragm valves with an EPDM diaphragm controlling the flow with handwheel operating member. Maximum working pressure 19.8 Bar. Maximum operating temperature 60°C.
Range of pressure sensors with stainless steel bodies, EPDM ‘O’-rings and ceramic diaphragms. Rectus 21 model has a maximum working pressure of 20.0 bar. ¼” BSP (M) model has a maximum working pressure of 50.0 bar. Cold water use only. From November 2019 Maximum operating temperature 85°C
Range of axial expansion joints with either threaded or flanged end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of combined bath filler, waste and overflow assemblies in various finishes. Maximum operating temperature 60ºC.
In-line plastic flow regulator housed within a brass body (chrome plated) or stainless steel body (HL2024 Cradle model only) incorporating a plastic strainer and EPDM ‘O’-rings. HL2024 Inline 1P BSP threaded models also have NBR/fibre gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Plastic bodied flow sensor. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Nova-Flo’ inline flow control device with a plastic body and EPDM ‘O’-rings. The product is intended to restrict the flow of water to a bath or basin if water level reaches the overflow. Float located within the overflow pathway activate flaps on each inlet to restrict the flow prior to the taps being closed. Maximum Working pressure 10.0 bar. Maximum operating temperature 60°C.
Hansen range of nylon BSP threaded fittings. For use above and below ground. Maximum working pressure 6mm - 50mm: 16.0bar, 65mm: 12.0bar, 80mm - 100mm: 10.0bar. Cold water use only.
NIVUS range of flow sensors with stainless steel bodies. Sensors incorporate EPDM seals and a PTFE olive. Maximum working pressure 16.0 bar. Cold water use only.
Range of shower hoses and riser rail with chromium plated brass bodies, incorporating EPDM ‘O’-rings. Maximum operating temperature 85°C.
Shower hose and handset with sliding rail and inlet kit. The inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of plastic manifold systems designed to accept interchanagble sensors (not supplied). Maximum working pressure 6.0 bar. Cold water use only.
Immersion temperature sensors with DZR bodies and an EPDM ‘O’-ring (STDW14 model only). Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
Wall brackets with brass bodies (chromium plated) and EPDM o-rings. Maximum working temperature 85°C
Range of shock arrestors with carbon steel or stainless steel bodies (available in various external surface finishes) incorporating Bromobutyl (BIIR) membranes. Maximum working pressure 10.0 bar. Cold water use only.
Range of shock arrestors with stainless steel bodies incorporating Bromobutyl (BIIR) membranes. Maximum working pressure 10.0 bar. Cold water use only.
Air break to drain, incorporating brass bodies with a grey epoxy powder coating. Maximum operating temperature 60°C.
Impeller with plastic body for insertion into specifically dimensioned bores. Maximum operating temperature 70°C.
Wall mounted chrome plated brass elbow fitting. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Hygienic flush box providing a timed flush facility. The supply is via a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection, flow sensor, spherical ball valve and strainer. The products incorporate a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The units have multiple interface user functions for timed flush, wireless technology and data storage. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Maincor Manifold having a brushed chrome plated body with 2 ,3 or 4 ports each with an isolation valve with red or blue indicators for hot and cold feeds. Supplied with a blanking plug and nut. Maximum working pressure 6.0 bar. Maximum operating temperature 75°C.
Assembly of pipe and fittings for use Arjo Huntleigh assisted bathing units. The assemblies comprise of either brass compression fittings or plastic push fit fittings for use with Uponor WIrsbo PEX pipe. The inlet of the 22mm assembly incorporates a combined spherical valve and strainer with brass body and stainless-steel filter. The strainer incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature for assemblies incorporating brass compression fittings is 80°C. Maximum operating temperature for assemblies incorporating PEX push fit fittings is 50°C.
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of in-line plastic flow regulators. The flow regulator is housed within a black plastic body incorporating a plastic strainer and an EPDM ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of flow through valves with brass bodies and EPDM ‘O’-rings, incorporating a spherical valve and a separate drain tap. The products are intended for connection prior to an expansion vessel. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of water monitoring systems comprising of a battery or mains operated latching solenoid valve (plastic body) and a flow sensor. The units are supplied with a hand-held controller. Maximum working pressure 10.0 bar. Cold water use only.
Range of click type pop-up wastes with brass bodies and EPDM rubber seals. Product is supplied with plastic back nuts.
Range of flow measurement devices (DZR brass) bodies incorporating two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of screwed gland cock valves with bronze bodies, EPDM seats and ‘O’-rings. The products incorporate a hose union outlet connection. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of DZR brass metering stations supplied with red and blue test points for upstream and downstream port identification. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Flow sensor with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Quick connector for connecting mixed water outlets to flexible hoses. Maximum operating temperature 60°C.
Range of pump docking manifolds with plastic bodies and NBR, EPDM and FKM ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.
Automatic, electronic, water control system, intended to be used for leak detection. Maximum working pressure 10.0 bar. Cold water use only.
Stainless steel bodied sensor with EPDM ‘O’-ring. Maximum operating temperature 90°C.
Range of flow sensors with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C
Range of wall mounted shower arms and shower handsets with brass bodies (various finishes), the inlets to the shower handsets incorporating a flow restrictor. Maximum operating temperature 60°C.
Thermostatic element with copper shell, polyethylene tube and PTFE gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of threaded fittings with either plain brass, nickel plated brass or chrome plated brass bodies. Maximum operating pressure 16.0 bar. Maximum operating temperature 99°C.
Wallgate CWC Series 250 WC pan with direct acting flush valve and DFKIT03 air break (DC device). WC flushing mechanism has a solenoid valve controlling the flow, the valves are operated via an infrared sensor or a piezo control button, this mechanism is fitted with a DC pipe interrupter, the DFKIT03 is fitted with a flow regulator. Maximum working pressure 2.0 bar. Cold water use only.
Shower kit, intended for use with ovens, incorporating a triple layered hose on a reel and a push-button operated shower handset. The inlet of the shower handset incorporates a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 4.0 bar. Cold water use only.
Range of circulation valves and flow sensor valves with EPDM seals and O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90ºC.
Range of concealed bathroom boxes with extractable shower hoses. The inlet attached to the concealed box incorporates an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the shower hose also includes a stainless steel strainer. Maximum operating temperature 60°C.
Range of pressure transmitters with stainless steel bodies. Maximum working pressures: DST-P140 model 25.0 bar, all other models 50.0 bar. Maximum operating temperature 90°C.
Vola 200M separate outlet socket with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Water hammer arrestor with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Shock arrestor with a carbon steel body and EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of eccentric hemisphere valves incorporating blue epoxy coated carbon steel bodies and discs, EPDM seat and a handwheel operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of combined bath filler, waste and overflow assemblies in various finishes. Maximum operating temperature 60ºC.
Keraflo range of a servo ceramic valves with DZR brass body. Maximum working pressure 6.0 bar. Cold water use only.
Wall mounted outlet with detachable shower hose connector (42037UK model) and wall mounted shower outlet (42018UK model). The 42018UK model is supplied with an optional, detachable shower hose connector assembly which incorporates an integral plastic flow regulator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model 42037UK has a maximum operating temperature of 80°C. Model 42018UK has a maximum operating temperature of 60°C.
Wall bracket with a brass body (chrome plated) and EPMD ‘O’-rings. Maximum operating temperature 85°C.
Screw down pattern, angled solation valve with a dome type operating member, DZR brass body and an EPDM gasket and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Chromium plated click type pop up waste with metal body and rubber seals. Supplied with a metal backnut.
Range of 2,3 or 4 way manifolds incorporating a nickel plated brass body with non-rising spindle stop valves. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower outlet elbows with brass bodies (chrome plated,with exception of model 27.076.LS0). Some models incorporate a shower handset holder. The outlet incorporates a check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Intelligent water assist valve consisting of a motorised quarter turn shut off valve which operates in the event a leak on the supply pipe to which it is fitted. Maximum working pressure 10 bar. Cold water use only.
Range of in-line flow sensors with a plastic body, turbine and impeller case. Maximum working pressure 25.0 bar. Cold water use only.
Range of compact wall outlet assemblies with plastic bodies (chromium plated) and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 55°C.
Plug with nylon body and stainless steel shaft. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Screw down elbow servicing valve with brass body (brushed chrome) which is intended to connect to an appliance, e.g. washing machine, dishwasher to the water supply. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of threaded fittings with either plain brass, nickel plated brass or chrome plated brass bodies. Maximum operating pressure 16.0 bar. Maximum operating temperature 99°C.
Shock arrestors with a carbon steel body and EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Concealed wall insulation unit with a brass body and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of isolation valves with a brass body (various surface finishes - see model) and either a quarter turn ceramic disc (PEX-230-C/P and PEX-231-C/P models) or a non-rising spindle (all other models) with various operating members (see model) and NBR ‘O’-rings. The inlet of the PEX-230-C/P and PEX-231-C/P models incorporates a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of shower hoses and riser rail with chromium plated brass bodies, incorporating EPDM ‘O’-rings. Maximum operating temperature 85°C.
Wall bracket with a brass body (chrome plated) and EPMD ‘O’-rings. Maximum operating temperature 85°C.
Range of handwheel operated hemisphere valves with blue epoxy coated ductile iron bodies, stainless-steel disc, seat and stems, and EDPM seals Maximum working pressure 10.0 bar. Maximum working temperature 80°C.
‘E-WATER BLOCK’ self-closing valves with black plastic bodies and stainless-steel filters. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Copper corrugated hose. Maximum working pressure 10.0 bar. Maximum working temperature 90°C.
Range of plastic bodied quarter turn isolation valves, with EPDM rubber ‘O’-rings, seals and washers. The 52.009.100 model is operated by a hex key (not supplied), the 52.009.200 model is operated by a key (supplied). Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Appliance inlet group assembly comprising of EPDM gaskets, a plastic bodied Y-pattern strainer, ¾” BSP (F) x ½” BSP (F) brass adaptor, a chrome plated DZR brass bodied double check valve assembly (suitable for backflow protection against Fluid Categry3), a ½” BSP (F) x ¾” BSP (M) brass adaptor, a dual layer hose with a PVC outer (grey) and PVC liner (black), a solenoid valve which incorporates a plastic strainer and a flow regulator within the inlet. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of water meter couplings with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only
Appliance inlet group assembly comprising of an EPDM gasket, ¾” BSP (F) x ½” BSP (F) brass adaptor, a chrome plated DZR brass bodied double check valve assembly (suitable for backflow protection against Fluid Categry3), a ½” BSP (F) x ¾” BSP (M) brass adaptor, a flexible reinforced hose assembly with a PVC lining and a solenoid valve which incorporates a plastic strainer and a flow regulator within the inlet. Maximum working pressure 5.0 bar. Cold water use only.
Range of hand wash and dryer units The flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a non-verifiable double check valve assembly (suitable for backflow protection against Fluid category 3) for installation on the inlet. The double check valve assembly also incorporates a drain port, (located in between the cartridges), and an integral spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 50ºC.
Pressure gauge with a plastic case, brass connector and bronze spring tube. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of flow and temperature sensors with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of circulation fittings with gun metal bodies, plastic cones & guides and EPDM ‘O’ rings. The products incorporate a dynamic venturi valve. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Pressure manager pump control unit with a plastic body. Maximum working pressure 10.0 bar. Cold water use only.
Copper corrugated hose. Maximum working pressure 10.0 bar. Maximum working temperature 90°C.
Bath spout incorporating a brass body (various finishes), EPDM ‘O’-rings and a plastic flow straightener. Maximum operating temperature 60°C
Range of pushfit hose connectors with either plastic (white or black) or chrome plated brass bodies and EPDM ‘O’-rings. SHCV prefix models incorporate screwdriver operated servicing valves. All pushfit connections are for use with PEX pipe (manufactured to BS7291-3) and copper pipe (manufactured to EN1057). Barbed end connections are not approved for use with any hose. Chrome plated brass body models are also for use with PB pipe (manufactured to BS7291-2). Maximum working pressure 10.0 bar (servicing valve models only). Barbed end connections are open outlet use only. Cold water use only.
Range of water hammer arrestor’s incorporating brass bodies (various finishes). The 525152 model is supplied with a reinforced captive nut. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of flow control valves for domestic hot water with plastic bodies and EPDM ‘O’-rings The products incorporate a motor which adjusts the flow, a flow sensor which measures the flow rate and a plastic filter on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pressure gauge with brass body and a plastic case. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C
Range of combined bath filler, waste and overflow assemblies in various finishes. Maximum operating temperature 60ºC.
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
External pump docking station with a plastic body and NBR ‘O’ rings. Cold water use only.
Range of radial flowmeters incorporating EPDM ‘O’-rings. The type 10088400 model has a black plastic body and threaded inlet. The type 10088402 model has a pale olive green plastic body with a threaded brass inlet incorporating a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Plastic bodied flow sensor with silicone gaskets. Maximum working pressure 17.5 bar. Maximum operating temperature 85°C.
Range of in line regulating valves DZR brass bodies, EPDM ‘O’-rings and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Thermally activated water saving valve with a plastic body and non-return valves on the hot and cold outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Water hammer arrestor with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pump inverters with plastic bodies, NBR rubber and EPDM rubber seals and ‘O’-rings. The products incorporate an inline resilient trim non-return valve. Maximum working pressure 13.0 bar. Cold water use only.
Bypass valve assembly with a plastic body and push/pull operating method to switch flows between different outlets. The product incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Cold water use only.
Union ball, non-return valve with a plastic PVC body. Maximum working pressure 10.0 bar. Cold water use only.
Range of three or four-hole single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Four hole models Incorporate quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to a shower outlet.. Three hole models Incorporate a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided PEX lined hose assemblies. The product is supplied with a shower hose and shower handset. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of concealed thermostatic mixing valves with DZR brass bodies incorporating a thermostatic cartridge controlling the temperature. The inlets incorporate asingle check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.
Range of pressure transmitters with stainless steel bodies. Maximum working pressure 10.0 to 200.0 bar (please refer to model). Maximum operating temperature 100°C.
Range of wall mounted handwash basins with copper piping and PTFE orings. Maximum working pressure 8.0bar. Maximum operating temperature 85°C
Range of compact wall outlet assemblies with plastic bodies (chromium plated) and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 55°C.
Manifold comprising of a PVC-U stub flange, PVC-U pipe and PVC-U tee fitting. Maximum working pressure 8.0 bar. Cold water use only.
Page of