Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'MORAPOX-WP'. Factory applied, two-part, red coloured epoxy coating comprising of a paint and hardener. Mix paint and hardener in a 2:1 volume ratio. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC4'. Factory applied, clear PTFE coating, intended for use with `O` rings, seals & gaskets. Apply as `Superior Group Quality Management System Procedure Reference 8.6’ referenced in document `LDAP-008 issue 1` released 01/05/2020. For use with water up to 85°C
`Suns-02`. Grey coloured, factory applied cement mortar. Mix, apply and cure as per user instructions 'doc: SUNS-U110320, version B` dated 2015-12. Cure for 24 hours@25°C. Between 1st May 2021 and 30th March 2022, the cement mortar is suitable for use with water up to 23°C. Between 31st March 2022 and 31st May 2026, the cement mortar is suitable for use with water up to 60°C
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET #1600 Gray F'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer`s instructions ref. no. '20210216-1' dated 2021/2/16. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP-621'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions file no: 'TJR-QM-CO-032', 'edition A1' dated '2021-Feb.-26th'. For use with water up to 65°C.
'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 1 of 53
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
