Section Code 2240 : Solenoid, plastic.
Back To Directory SectionsRange of solenoid valves with plastic bodies and EPDM diaphragms. The 1180 models have a plastic flow regulator on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C (1180 models) and 60°C (2180 model).
Range of solenoid valves with plastic bodies and EPDM membrane. Maximum working pressure 10.0 Bar. Maximum operating temperature 65ºC
Range of latching solenoid valves with plastic bodies and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Solenoid valve with plastic bodies and EPDM O-rings, for insertion into specifically dimensioned bores. The inlet incorporates a stainless steel strainer. Product is available normally closed or latching. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of solenoid valves with plastic bodies and EPDM rubber diaphragms, incorporating stainless steel strainers and plastic strainers in the inlets and plastic flow regulators. Maximum working pressure 8.0 bar. Cold water use only.
Range of normally closed solenoid valves with plastic bodies, incorporating EPDM ‘O’ rings and diaphragms. The inlets incorporate a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of solenoid valves with plastic bodies, incorporating stainless steel strainers in the inlets. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
V38HI solenoid valves with nylon bodies, NBR or EPDM diaphragms and a plastic filter/regulator at the inlet. Maximum working pressure 10.0 bar. Cold water only.
Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and the outlet incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of latching (LV), proportional (PV), servo (SV) and pilot (EV) solenoid valves with plastic bodies (pale olive green - model 118/D is also available in a black coloured variant), incorporating either EPDM or silicone diaphragms. Bodies with ¾” BSP (M) inlets may incorporate an optional approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. From September 2019 body variants 118/D and 118/E have the option of black bodies with antimicrobial biocide. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of normally closed solenoid valves with plastic bodies and silicone rubber diaphragms. Maximum working pressure 0.07446 bar. Maximum operating temperature 65°C.
Solenoid valve with plastic body, NBR or EPDM diaphragms and a plastic filter/regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
V18HT solenoid valves with plastic body, NBR or EPDM diaphragm and a plastic filter/regulator at the inlet. Maximum working pressure 10.0 bar. Cold water only.
Solenoid cartridge, servo controlled valve with plastic body, EPDM membrane and push button operation. Maximum working pressure 10.0 bar. Maximum operating temperature 75°C.
‘V’ and ‘VAI’ Ranges of solenoid valves with nylon bodies, incorporating EPDM O-rings and diaphragms. V series models are available with multiple outlet options in various sizes. Models also incorporate a plastic flow regulator and a strainer. Maximum working pressure 10.0 Bar. Cold water use only.
Range of normally open, normally closed or latching, in-line solenoids valves incorporating a manual override and adjustable flow limiter with nylon bodies (available in black or off-white), NBR O-rings and diaphragms. Maximum working pressure 10.0 bar. Cold water use only. From September 2019 the ¾” BSP (F) & (M) and the 2” BSP (F) valves (and these sizes only) are approved with a maximum operating temperature of 60°C. All other sizes remain cold water use.
‘R Series, R Series Mini, R Series Dispenser, R Series Dual, R Series Universal & R Series Modular’ ranges of normally closed, normally open or latching solenoid valves with off-white nylon bodies, incorporating either NBR or silicone diaphragms with POM diaphragm inserts (only). The inlet or outlet can incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet can also incorporate a plastic flow restrictor. The inlet can also incorporate a plastic strainer or a plastic flow regulator. (This option is not available on the push fit (quick coupling) sizes added September 2020). ‘R Series’ models are available as either in-line or at a 90° angle (hose tail outlet models only), except for ‘R series modular’ models added July 2019 which are only available at a 90° angle. From January 2020 models are available with the RF flow meter. From November 2020 models are available with the RV filters, which are stainless steel filters with nylon bodies to be mounted on every Serie R model body in place of the solenoid. Models with a push fit (quick coupling) connection added September 2020 are for use with LLDPE pipe (all sizes), or PEX pipe (manufactured to BS7291-3) (10mm & 15mm sizes only). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C, except for models fitted with a flow meter or Series R filter which are cold water use only.
Range of servo-controlled and normally closed (NC) solenoid valves with various plastic bodies and various inlet / outlet options. Inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of solenoid valves with plastic bodies and silicone diaphragms. The outlets incorporate a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.03 bar. Maximum operating temperature 65°C
Servo assisted, normally closed solenoid valve with a plastic body and EPDM membrane. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10 bar. Cold water use only
Range of solenoid valves with plastic bodies, (optional antimicrobial biocide body) incorporating either EPDM or silicone diaphragms. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Ranges of solenoid valves with plastic bodies, incorporating EPDM ‘O’-rings and diaphragms. Models also incorporate a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only. From September 2020, the maximum operating temperature is 90.0°C
Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies, integral stainless steel strainer, EPDM diaphragm, EPDM ‘O’-rings and seals. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Normally closed solenoid valve with a plastic body and EPDM diaphragm. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of plastic bodied normally closed latching solenoid valves. The 42424000 model is supplied with an additional brass housing. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Non latching solenoid valve with a plastic body and an EPDM gasket and ‘O’-ring. Maximum working pressure 8.0 bar. Cold water use only.
Solenoid valves with a plastic body and silicone diaphragm and ‘O’ rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.
Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C
Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.18 Bar. Cold water use only.
Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and an integrated flow meter sensor. Both the inlet and the outlet incorporate a white plastic flow restrictor. The products are also supplied with an optional EPDM outlet gasket, for installation over the outlet spigot. Maximum working pressure 10.0 bar (to diaphragm). Maximum operating temperature 85°C.
Range of plastic bodied solenoid valves incorporating a stainless steel spring and armature with an EPDM diaphragm. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of normally closed and normally open plastic solenoid valves with EPDM ‘O’-rings and sealing rings. Pushfit connections for use with John Guest LLDPE pipe or copper pipe. The 47.004.103 model acts as a diverter between two outlets, where one outlet is always open. Maximum working pressures see model section. Maximum operating temperatures: 65°C - 47.00X.1XX models with John Guest LLDPE pipe only. 90°C - 47.004.103 model with John Guest LLDPE pipe only. Models added January 2021: Cold water use only - 47.00X.2XX (4mm & 8mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm & 8mm) with copper pipe only.
Aquatsop leak detection system intended to shut the water supply in the event of a water leak. Consisting of two single normally closed servo controlled solenoid valves with a flow regulator and stainless steel filter at the inlet. A LDPE inner hose with corrugated plastic outer hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of latching and normally closed (see model) solenoid valves with plastic bodies, NBR diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Solenoid valve incorporating a plastic body and an EPDM diaphragm. The product incorporates a plastic flow regulator with an EPDM washer, and a plastic filter on the inlet. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Solenoid valve with a plastic body and an EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Solenoid valve with plastic body and an EPDM membrane. The inlet incorporates a plastic strainer and a plastic flow regulator. The product is also supplied with an optional stainless-steel strainer for installation on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Plastic bodied solenoid valve available as both a latching and normally closed variant, with an EPDM diaphragm and ‘O’-rings. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
‘1175B’ range of servo-controlled normally closed (NC), normally open (NO) or latching solenoid valves with off-white nylon bodies, incorporating a NBR diaphragm with POM diaphragm inserts. For use with copper tube manufactured to EN1057 or John Guest Speedfit barrier pipe manufactured to BS7291 part 3. Maximum working pressure 10.0 bar. Cold water use only.
Page of