Water Regulations Approval Scheme Ltd

Brymec Ltd Approvals

WRAS Approval Number: #1912059

Range of in-line servicing valves nickel-plated brass body and ball with EPDM gaskets and either a screwdriver or Butterfly operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:: 2260 Valves
Section Subtitle:: Spherical, metal.
WRAS Approval Number:: 1912059
Expiry date:: 31/12/2024
Size:: 22mm compression inlet/outlet
Marking:: BRYMEC, SIZE & EN1254-2 ON FERRULE WRAS, SIZE, FLOW ARROW & DATE OF MANUFACTURE MM/YY ON BODY
Installation Requirements:: R001
Model:: Screwdriver operated. 36373 (Nickel plated Brass) Butterfly operated. 30841 (Nickel plated Brass)
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2107585

'Brymec PVC Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'TDS Brymec CEMENT Rev 01' review date '27-05-2022'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:: 5560 Solvent Cements
WRAS Approval Number:: 2107585
Expiry date:: 31/07/2026
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2001158

Range of non-verifiable double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. The products incorporate a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:: 0034 Backflow Prevention Devices
Section Subtitle:: SCHEDULE 2 - Section 6.2 Type ED - Non-verifiable double check valve.
WRAS Approval Number:: 2001158
Expiry date:: 31/01/2025
Note:: Not for use with water injected with CO2 gas.
Size:: see model
Marking:: WRAS, size, flow arrow and CR marking on body. Brymec, EN1245-2 & size on compression nuts.
Installation Requirements:: R001
Model:: 30766 - 15mm compression. 30773 (Nickel plated) - 15mm compression. 30767- 22mm compression. 30768 - 28mm compression.
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2012108

Range of brass press fittings with EPDM ‘O’-rings for use with EN ISO 21003 pipe. Maximum working pressure 10.0 bar. For cold water use only.

Section:: 1180 Fittings for use with Tube and Pipe
Section Subtitle:: Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use
WRAS Approval Number:: 2012108
Expiry date:: 31/12/2025
Size:: Please refer to model.
Marking:: Brymec logo, size & Crimp Profiles (U-TH-H) on crimp sleeve.
Installation Requirements:: R001
Model:: 51019 ∙ 16mm Brass Coupler Multilayer Crimp Fitting 51020 ∙ 20mm Brass Coupler Multilayer Crimp Fitting 51018 ∙ 25mm Brass Coupler Multilayer Crimp Fitting 51022 ∙ 32mm Brass Coupler Multilayer Crimp Fitting 51028 ∙ 20x16mm Reducing Coupler Multilayer Crimp Fitting 51040 ∙ 25x16mm Reducing Coupler Multilayer Crimp Fitting 51038 ∙ 25x20mm Reducing Coupler Multilayer Crimp Fitting 51031 ∙ 32x16mm Reducing Coupler Multilayer Crimp Fitting 51032 ∙ 32x20mm Reducing Coupler Multilayer Crimp Fitting 51039 ∙ 32x25mm Reducing Coupler Multilayer Crimp Fitting 51044 ∙ 16mm Brass 90 Elbow Multilayer Crimp Fitting 51045 ∙ 20mm Brass 90 Elbow Multilayer Crimp Fitting 51043 ∙ 25mm Brass 90 Elbow Multilayer Crimp Fitting 51047 ∙ 32mm Brass 90 Elbow Multilayer Crimp Fitting 51058 ∙ 16mm Brass Equal Tee Multilayer Crimp Fitting 51059 ∙ 20mm Brass Equal Tee Multilayer Crimp Fitting 51042 ∙ 25mm Brass Equal Tee Multilayer Crimp Fitting 51061 ∙ 32mm Brass Equal Tee Multilayer Crimp Fitting 51140 ∙ 16x16x20mm Reducing Ends Tee Multilayer Crimp 51142 ∙ 20x16x16mm Reducing End & Branch Tee Multilayer Crimp 51121 ∙ 20x20x16mm Reducing Branch Tee Multilayer Crimp 51137 ∙ 20x20x25mm Reducing Ends Tee Multilayer Crimp 51147 ∙ 25x20x20mm Reducing End & Branch Tee Multilayer Crimp 51124 ∙ 25x25x16mm Reducing Branch Tee Multilayer Crimp 51125 ∙ 25x25x20mm Reducing Branch Tee Multilayer Crimp 51129 ∙ 32x32x20mm Reducing Branch Tee Multilayer Crimp 51130 ∙ 32x32x25mm Reducing Branch Tee Multilayer Crimp 51155 ∙ 16mm x 1/2" Female Iron Branch Tee Multilayer Crimp 51156 ∙ 20mm x 1/2" Female Iron Branch Tee Multilayer Crimp 51157 ∙ 25mm x 3/4" Female Iron Branch Tee Multilayer Crimp 51081 ∙ 16mm x 1/2" Male Iron Multilayer Crimp Coupler 51083 ∙ 20mm x 1/2" Male Iron Multilayer Crimp Coupler 51084 ∙ 20mm x 3/4" Male Iron Multilayer Crimp Coupler 51082 ∙ 25mm x 3/4" Male Iron Multilayer Crimp Fitting 51085 ∙ 25mm x 1" Male Iron Multilayer Crimp Fitting 51088 ∙ 32mm x 1" Male Iron Multilayer Crimp Coupler 51067 ∙ 16mm x 1/2" Female Iron Multilayer Crimp Coupler 51069 ∙ 20mm x 1/2" Female Iron Multilayer Crimp Coupler 51070 ∙ 20mm x 3/4" Female Iron Multilayer Crimp Coupler 51095 ∙ 25mm x 3/4" Female Iron Multilayer Crimp Fitting 51068 ∙ 25mm x 1" Female Iron Multilayer Crimp Fitting 51073 ∙ 32mm x 1" Female Iron Multilayer Crimp Coupler 51096 ∙ 16mm x 1/2" Male Iron Elbow Multilayer Crimp Fitting 51098 ∙ 20mm x 3/4" Male Iron Elbow Multilayer Crimp Fitting 51099 ∙ 25mm x 1" Male Iron Elbow Multilayer Crimp Fitting 51171 ∙ 16mm x 1/2" Backplate Elbow Multilayer Crimp 51173 ∙ 20mm x 3/4" Backplate Elbow Multilayer Crimp 51108 ∙ 16mm x 1/2" Female Iron Elbow Multilayer Crimp Fitting 51107 ∙ 20mm x 1/2" Female Iron Elbow Multilayer Crimp Fitting 51109 ∙ 20mm x 3/4" Female Iron Elbow Multilayer Crimp Fitting 51105 ∙ 25mm x 3/4" Female Iron Elbow Multilayer Crimp Fitting 51106 ∙ 25mm x 1" Female Iron Elbow Multilayer Crimp Fitting
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2005052

Range of screw down stop valves with brass bodies. Fittings incorporate EPDM seat washers and PTFE seals. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:: 2310 Valves
Section Subtitle:: Stop, metal, screw down.
WRAS Approval Number:: 2005052
Expiry date:: 31/05/2025
Size:: ½” - 2” BSP (F) 15mm - 54mm compression 15mm - 20mm compression 15mm - 25mm compression 22mm - 25mm compression
Marking:: WRAS, FLOW ARROW & SIZE ON BODY BRYMEC & SIZE ON END NUT
Installation Requirements:: R001
Model:: Compression stop cock for use with copper pipe: 36384, 36385 & 36386
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2204711

Range of lock shield or handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:: 2290 Valves
Section Subtitle:: Stop, gate, metal.
WRAS Approval Number:: 2204711
Expiry date:: 30/04/2027
Size:: see model
Marking:: WRAS, FLOW ARROW & SIZE ON BODY BRYMEC & SIZE ON COMPRESSION NUT
Installation Requirements:: R001
Model:: Gate valve: 30813 – 15MM 30814 – 22MM 30815 – 28MM Lock shield Gate valve : 30700 – 15MM 30707 – 22MM 30299 – 28MM
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2010112

Range of in-line `Y`-patterned strainers with brass bodies incorporating a stainless steel mesh strainer and a PTFE washer. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C

Section:: 1715 Strainers
WRAS Approval Number:: 2010112
Expiry date:: 31/10/2025
Size:: See model.
Marking:: Brymec logo, PN, DN, flow arrow and size on body.
Installation Requirements:: R001 R120
Model:: Brass: 36233: ½” BSP (F). 36234: ¾” BSP (F). 36235: 1” BSP (F). 36236: 1¼” BSP (F). 36237: 1½” BSP (F). 36238: 2” BSP (F).
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2109066

Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:: 0030 Backflow Prevention Devices
Section Subtitle:: SCHEDULE 2 - Section 6.2 Type EB - Non verifiable single check valve.
WRAS Approval Number:: 2109066
Expiry date:: 30/09/2026
Size:: 30780 ∙ 15mm Brass Single Check Valve Compression 30781 ∙ 22mm Brass Single Check Valve Compression
Marking:: WRAS, BRYMEC, CR, size, PN and flow arrow on body.
Installation Requirements:: R001
Model:: 30780 & 30781
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2209064

Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C

Section:: 0034 Backflow Prevention Devices
Section Subtitle:: SCHEDULE 2 - Section 6.2 Type ED - Non-verifiable double check valve.
WRAS Approval Number:: 2209064
Expiry date:: 30/09/2027
Size:: see model
Marking:: Brymec logo, WRAS, size, flow arrow and CR on body
Installation Requirements:: R001
Model:: 36366 ½” BSP (F) inlet/outlet 36367 ¾” BSP (F) inlet/outlet 36368 1” BSP (F) inlet/outlet 36369 1.1/4" BSP (F) inlet/outlet 36370 1½” BSP (F) inlet/outlet 36371 2” BSP (F) inlet/outlet
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company

WRAS Approval Number: #2210060

Range of solder ring copper fittings for use with copper tube to BS EN 1057. Maximum working pressure 16 bar. Maximum working temperature 99°C

Section:: 1115 Fittings for use with Tube and Pipe
Section Subtitle:: Capillary, solder ring, lead free. Unless specified in the individual approval, the products within this section are not suitable for below ground use
WRAS Approval Number:: 2210060
Expiry date:: 31/10/2027
Size:: 15MM, 22MM, 28MM, 35MM, 42MM, 54MM
Marking:: Brymec, EN1254 and size on body.
Installation Requirements:: R001
Model:: 30289 Solder ring coupler 15mm 30290 Solder ring coupler 22mm 30291 Solder ring coupler 28mm 30292 Solder ring coupler 35mm 30293 Solder ring coupler 42mm 30294 Solder ring coupler 54mm 30390 Solder ring reducing coupler 22mm x 15mm 30374 Fitting reducer 22mm x 15mm 30375 Fitting reducer 28mm x 15mm 30376 Fitting reducer 28mm x 22mm 30377 Fitting reducer 35mm x 15mm 30378 Fitting reducer 35mm x 22mm 30379 Fitting reducer 35mm x 22mm 30380 Fitting reducer 42mm x 15mm 30381 Fitting reducer 42mm x 22mm 30382 Fitting reducer 42mm x 28mm 30383 Fitting reducer 42mm x 35mm 30384 Fitting reducer 54mm x 22mm 30385 Fitting reducer 54mm x 28mm 30386 Fitting reducer 54mm x 35mm 30387 Fitting reducer 54mm x 42mm 30393 90° Street elbow 15mm 30394 90° Street elbow 22mm 30395 90° Street elbow 28mm 30320 90° elbow 15mm 30321 90° elbow 22mm 30322 90° elbow 28mm 30323 90° elbow 35mm 30324 90° elbow 42mm 30325 90° elbow 54mm 30331 45° elbow 15mm 30332 45° elbow 22mm 30333 45° elbow 28mm 30334 45° elbow 35mm 30335 45° elbow 42mm 30336 45° elbow 54mm 30345 Equal tee 15mm 30346 Equal tee 22mm 30347 Equal tee 28mm 30348 Equal tee 35mm 30349 Equal tee 42mm 30350 Equal tee 54mm 30423 Reducing tee 15mm x 15mm x 22mm 30424 Reducing tee 22mm x 15mm x 15mm 30425 Reducing tee 22mm x 15mm x 22mm 30426 Reducing tee 22mm x 22mm x 15mm Model name/s of secondary products 30427 Reducing tee 22mm x 22mm x 28mm 30429 Reducing tee 28mm x 15mm x 15mm 30430 Reducing tee 28mm x 15mm x 28mm 30431 Reducing tee 28mm x 22mm x 15mm 30432 Reducing tee 28mm x 22mm x 22mm 30433 Reducing tee 28mm x 22mm x 28mm 30434 Reducing tee 28mm x 28mm x 15mm 30435 Reducing tee 28mm x 28mm x 22mm 30436 Reducing tee 35mm x 35mm x 15mm 30437 Reducing tee 35mm x 35mm x 22mm 30438 Reducing tee 35mm x 35mm x 28mm 30439 Reducing tee 42mm x 42mm x 15mm 30440 Reducing tee 42mm x 42mm x 22mm 30441 Reducing tee 42mm x 42mm x 28mm 30442 Reducing tee 42mm x 42mm x 35mm 30449 Reducing tee 54mm x 54mm x 15mm 30443 Reducing tee 54mm x 54mm x 22mm 30446 Reducing tee 54mm x 54mm x 28mm 30447 Reducing tee 54mm x 54mm x 35mm 30448 Reducing tee 54mm x 54mm x 42mm 30359 End caps 15mm 30360 End caps 22mm 30361 End caps 28mm 30362 End caps 35mm 30363 End caps 42mm 30364 End caps 54mm
Approval Holder:: Brymec Ltd

Company Name
Brymec Ltd
Address
Redlands , Coulsdon, Surrey
Postcode
CR5 2HT
General Email
Jeremy.douglas@brymec.com

View All Listings by this Company