Section Code 2420 : Drinking.
Back To Directory SectionsFree standing drinking water cooler housed in a stainless steel tank, dispensing ambient or chilled water. Models with ‘WG’ in the model name can also dispense sparkling water. Flow is controlled via a solenoid valve and push button assembly (except for models with ‘IN’ in the model name, which are pass-through models where flow is controlled by external taps or dispensing equipment, which are not covered as part of this approval). Models with ‘WG’ in the model name incorporate two single check valve cartridges on inlet to the carbonisation unit (suitable for backflow protection against Fluid Category 3). Maximum working pressure 6.0 bar. Cold water supply only.
Range of free standing and countertop, cold, ambient or hot water dispensing units with flow controlled by float valve and discharged via either a solenoid operated push button or self-closing tap. Maximum working pressure 5.0 Bar. Cold water use only.
‘Zip Hydro Tap’ range of single hole, double outlet, fixed combination tap assemblies (chromium plated brass) with electronic controlled functions to allow the tap to dispense boiling or also ambient water via the supplied Zip under counter units and solenoid valves. The spout outlets incorporate a plastic flow straightener. Both models incorporate a separate vent outlet within the tap spout for the boiling water circuit. The products are supplied with a loose pressure limiting valve, single check valve assembly (suitable for backflow protection against Fluid Category 2) and in-line water filter for connection on the supply to the under counter unit. Maximum working pressure 7.0 bar, 5.0 bar without pressure limiting valve. Inlet to under counter unit cold water supply only. Maximum operating temperature 100°C.
‘Zip Hydro Tap’ range of single hole, double outlet, swivel combination tap assemblies (chromium plated brass) with electronic controlled functions to allow the tap to dispense boiling water (all models) via the supplied Zip under counter units and solenoid valves. The products also incorporate a separate ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Both models incorporate a separate vent outlet within the tap spout for the boiling water circuit. The products are supplied with a loose pressure limiting valve, single check valve assembly (suitable for backflow protection against Fluid Category 2) and in-line water filter for connection on the supply to the under counter unit. Maximum working pressure 7.0 bar, 5.0 bar without pressure limiting valve. Inlet to under counter unit cold water supply only. Maximum operating temperature 100°C (boiling water outlet), 65°C (mixed water - hot and cold supplies to ceramic cartridge).
Chiller/cooling unit intended to supply a water fountain. Maximum working pressure 10.0 bar. Cold water use only.
‘Icecore 1' ambient water chiller unit. Maximum working pressure 6.2 bar. Cold water use only.
Range of under-sink mounted water chillers with either an ice block or aluminium cooling block and plastic tubing and fittings. Maximum working pressure 3.5 bar. Maximum operating temperature 30°C.
In-line water chiller unit intended to supply a water fountain. The product is supplied with a loose in-line stainless steel strainer. Maximum working pressure 7.25 bar. Cold water use only.
In-line water chiller unit intended to supply a water fountain. The product is supplied with a loose in-line stainless steel strainer. Maximum working pressure 7.25 bar. Cold water use only.
Range of under counter units providing (near) instant boiling and chilled water (Quadra/Sahara /Eco models) or chilled and ambient water (Alpine 125 model) through the XL, XT or XR taps. Where products are supplied with the XL, XT, XR taps the flow is controlled via a solenoid valve incorporating a plastic strainer which is activated by a lever (XL tap), touch method (XT tap) or a remote control (XR tap). The under counter units incorporate a combined pressure limiting valve (set at 5.0 Bar) and a double check valve assembly (suitable for backflow protection against Fluid Category 3) on the inlet and are supplied with a loose stainless steel braided PEX lined flexible hose assembly incorporating a ½” captive nut end connection for installation on the inlet. The under counter units also incorporate a water filter on the cold supply after the solenoid valve. The filter head inlet incorporates an approved single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides adequate backflow protection - but is incorporated after the double check valve assembly). (The filter is installed downstream of the combined pressure limiting valve and a double check valve assembly). The Quadra and Sahara plus models incorporate a venturi block assembly fed [cold water] from and then [hot water from hot tank] back to a mixer tap (not supplied). The venturi block assembly incorporates an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides adequate backflow protection). Under counter unit supplying XL, XT, XR taps: Maximum inlet pressure 10.0 bar. Cold supply only. Maximum working temperature of the instantaneous heater (where incorporated - model dependent) 98.5°C. Quadra and Sahara plus models mixer tap (not supplied) cold supply and hot water circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Counter-top water dispenser providing instantaneous hot and cold water. Flow to the hot water tank is controlled by a solenoid valve and actuated via a water level sensor. The discharge of both hot and chilled water is operated by self-closing tap assemblies. The product incorporates a pressure reducing valve set at 0.9 bar. The inlet incorporates an approved single check valve cartridge; however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 7.0 bar. Maximum operating temperature 96°C. Cold water supply only.
Range of cold or cold carbonated water cooler units with the flow controlled via solenoid valve. The product incorporates a double check valve assembly. Maximum working pressure 3.5 Bar. Cold water use only.
Range of cold or cold carbonated water cooler units with the flow controlled via solenoid valve. Maximum working pressure 3.5 Bar. Cold water use only.
‘NIAGARA FAMILY’ range of free standing or table top, ambient, chilled or sparkling water (with gas) dispensing units with flow controlled via either a solenoid operated push button or an external tap or dispensing equipment. The units incorporate solenoid valves, PE hoses, plastic fittings. Models including ‘WG’ as part of the model incorporate a non-verifiable single check valve assembly (suitable for backflow protection against Fluid Category 2). The ACWG (EC) models incorporates a pump and a carbonating unit. The outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Cold water use only.
`River` range of drinking water fountains which dispense ambient and/or chilled water. Flow is controlled via self-closing headworks. Maximum working pressure 6.0 bar. Cold water use only
Range of under-sink mounted water chiller with a stainless-steel cooling tank and plastic fittings Maximum working pressure 3.0 bar. Maximum operating temperature 38°C.
Range of inline under counter water chillers incorporating stainless steel coil tubing. Maximum working pressure 5.5 Bar. Cold water use only.
Range of under-counter or counter-top drinking water dispensers delivering still ambient, still chilled & sparkling water. HygienePlus®. Models incorporate a built-in filter system. The flow is controlled by a solenoid valve which is either operated by a touch or a touch pad. The water is dispensed via a tap arrangement on under-counter versions or an integrated outlet on counter-top versions. The inlets incorporate an approved check valve cartridge assembly however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Cold water use only.
Range of water fountains and bottle fillers, water fountains which can be chilled or ambient outlet temperatures, incorporating a solenoid controlling the flow which is activated via either a push button or IR activated sensor. Split level models incorporate both bottle filler and fountain outlets. Maximum working pressure 7.0 bar. Cold water use only.
Range of undercounter or deck mounted drinking water fountains which dispense ambient and/or chilled water. Flow is controlled via a solenoid valve and the products are activated via a push button or infa-red sensor . Maximum working pressure 7.0 bar. Cold water use only.
Water chiller unit for under counter installation, to be used in conjunction with an outlet tap arrangement or flow control device (not supplied as part of this approval). Maximum working pressure 7.0 bar. Cold water use only.
Page of
