Section Code 1510 :
Back To Directory SectionsRange of water meter manifolds, meter carriers and stopcock carriers with DZR brass bodies (manifold and meter carriers), bronze body (stopcock carrier) and NBR ‘O’-rings. Manifold and stopcock carrier incorporate screw down stop valves with rising spindle headworks. Meter carrier and stopcock carrier also incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
‘Talbot Modular Interchangeable Manifold System’ with plastic bodies, available in 2 - 12 port variants. Each outlet port incorporates a screw down stop valve. The products are supplied with loose pipe inserts. The products added June 2017 incorporate a non-return valve (not tested for backflow protection). Maximum working pressure 16.0 bar. For cold water use only.
Range of concentric water meter manifolds (gunmetal body) incorporating ¼ turn spherical valves, a non-return valve (not suitable for backflow prevention) and provision for connection of a water meter or flow cap. Maximum working pressure 16.0 bar. Cold Water Use only.
`Waterfit` water meter manifold assembly (acetal body) which incorporates a spherical valve, drain valve and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 12.5 bar. Cold water & above ground use only.
Range of single or manifold below ground meter boxes. The boxes incorporate a concentric water meter manifold and a servicing valve on each connection. Each meter manifold incorporates a non-return valve (not intended for backflow protection). The push-fit inlet and outlet connections are supplied with pipe inserts and are for use with MDPE pipe (manufactured to EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range multi manifold below ground meter boxes. The boxes incorporate a concentric water meter manifold with either quarter turn or rising spindle servicing valves. The meter manifold incorporates a non-return valve (not suitable for backflow prevention). The push-fit outlet connections are supplied with pipe inserts and are for use with MDPE pipe (manufactured to EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds with plastic bodies. Inlets incorporate spherical isolation valves. Products also incorporate a non-return valve (not suitable for back flow protection). Compression models are for use with metric and imperial PE pipe. Maximum working pressure 16.0 bar. Cold water use only.
Water meter manifold assembly with gunmetal body, incorporating a non-return valve (not suitable for backflow protection) and servicing valve. The water meter manifold is supplied with a blue plastic (full flow) cap to be installed when metering is not required. Maximum working pressure 16.0 bar. Cold water use only.
Water meter manifold with DZR brass body. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Cold water use only.
Range of AJUSTA water meter chambers with plastic bodied manifold assemblies. The inlet incorporates a screw down servicing valve & the chamber incorporates non-return valves (not suitable for back flow protection). Maximum working pressure 12.0 bar. Cold water use only.
Range of water meter manifolds (plastic bodies), incorporating a screwdown stop valve, a single check valve (not intended for backflow prevention) and provision for connection of a water meter or flow cap. The 3517 models incorporate a ‘blanked off’ drain off spigot which Plasson has advised is not intended to be used. The compression connections are only for use with PE pipe to EN 12201:2. The 3517 model 15mm outlet connection is only for use with copper pipe to EN 1057, and the 22mm outlet connection is only for use with copper pipe to EN 1057, PB pipe to BS EN 7291 part 2 and PEX pipe to BS EN 7291 part 3. Maximum working pressure 12.0 bar. Cold water use only.
‘EBCO’ range of water meter boxes with plastic or gunmetal manifolds. The inlets to manifolds incorporate a quarter turn isolation valve. The products also incorporate an approved check valve cartridge; however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection - and is not intended for this purpose. Below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Water meter manifold with gunmetal body, brass connections, EPDM seal and NBR ‘O’-rings. The product incorporates a non-return valve after the meter location and a servicing valve on the inlet. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds with plastic bodies incorporating a drain off valve. Inlets incorporate a plastic strainer. Products also incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Cold water use only. Maximum working pressure 16.0 bar.
Range of water meter manifolds with plastic bodies. The inlets incorporate a spherical valve and a non-return valve (not suitable for back flow protection). Model MD1010101BM is for use with Irish Heavy gauge pipe manufactured to 15134/1977. All other models are for use with blue MDPE pipe manufactured to EN12201. Maximum working pressure 12.5 bar. Cold water use only.
Range of water meter manifolds with a plastic body and a spherical valve at the inlet. Models MB2012525DM & MB2010303DM incorporates two single check valve cartridges, all other models incorporate one single check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection Model MB201010BM is for use with Irish Heavy gauge pipe manufactured to 15134/1977. All other models are for use with blue MDPE pipe manufactured to EN12201. Maximum working pressure 12.5 bar. Cold water use only.
Range of water meter manifolds incorporating DZR brass bodies, PTFE washers, a non-return valve and ball valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of water meter assemblies which incorporating DZR brass bodies, spherical valve and pressure reducing valve (1.5 to 6.0 bar range). The products incorporate two approved, in-line single check valve cartridges, (verified by test, suitable for backflow protection against Fluid Category 3). Fitting is also supplied with a pressure guage. Maximum working pressure 10.0 bar. Cold water use only.
Range of water meter manifolds (also known as double box valves) for use with MDPE pipe (manufactured to BS EN 12201). The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 16 bar. Cold water use only.
Range of ‘Resident Valves’ with a DZR brass body consisting of water meter manifold, an isolation valve on the inlet, a pressure reducing valve (adjustable between 1.5 and 6.0 bar) and 2 non-return valves which are located on the outlet of the water meter manifold. The ‘Plus’ models are also supplied with an isolation valve on the outlet, which incorporates a drain tap. Maximum supply pressure 16.0 Bar. Cold water above ground use only.
Page of
