Range of wall mounted, concealed, thermostatic mixing vales with brass bodies and chrome plated trim sets, incorporating one or two quarter turn ceramic disc headworks with various operating members (see models). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork (with various operating members). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature is 85°C.
Range of water filters cartridges with plastic bodies and either carbon block or activated carbon filter media. Maximum working pressure 8.6 bar. Maximum operating temperature 38°C.
Range of wall mounted thermostatic shower valves (chrome plated) brass bodies incorporating a single sequential thermostatic cartridge controlling both flow and temperature. Models 86005770 & 86005780 have single lever operating members. Model 86005760 is not supplied with an operating member. both inlets incorporate single check valve cartridges (suitable for backflow protection against fluid category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic shower valves incorporating brass bodies (chrome plated) and a quarter turn ceramic disc headwork controlling the flow with single lever, cross top or dome type operating members. The temperature controlled is independently via a thermostatic cartridge incorporating a manual override button with cross top, dome type or single lever operating members. Both inlets incorporate stainless steel strainers and approved single check valve cartridges however, the complete assemblies have not been fully tested to demonstrate that they provide adequate backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic bar shower valve, riser rail, shower handset, shower hose and overhead shower outlet. The valve incorporates a brass body (chrome plated) and ceramic disc headwork with dome type operating member which controls and diverts the flow between the two shower outlets. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The inlets incorporate stainless steel filters and a single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Thermostatic cartridge with brass body, and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic mixing valves with a brushed Zinc alloy plated brass body (various operating members) and NBR `O`-rings incorporating a thermostatic cartridge controlling the temperature with a manual override button, a ceramic disc headwork controlling the flow. Both inlets incorporate a single check valve cartridge, (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall mounted thermostatic blending valve (chromium plated brass), incorporating a quarter turn ceramic disc headwork with dome type operating members. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature is 85°C.
Range of wall mounted, exposed, thermostatic bar type shower mixing valves (chromium plated brass). The246PG model incorporates a 2-way ceramic disc diverter headwork with a dome type operating member controlling the flow between an overhead shower outlet and a shower handset. The 536PG model incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the flow to a shower handset. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Both products are supplied with a shower hose and handset, the B36264 model also includes a shower riser to an overhead shower outlet. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wafer and lugged type, concentric butterfly valves with epoxy coated cast iron bodies, austenitic steel discs and EPDM seats. Maximum working pressure 16.0 bar. Cold water use only.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies & wedges and EPDM sealing gasket. The closing mechanism is controlled by a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85˚C.
Range of lug type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs, EPDM seats and lever type operating member. Maximum working pressure 16.0 bar (models 2108 12, 2108 13 and 2108 14). Maximum working pressure 10.0 bar (models 210816 and 2108 18). Maximum operating temperature 100°C.
Range of lug type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs, EPDM seats and lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of shower bars with brass bodies (various finishes), incorporating a manual diverter with cube or dome type operating members, which diverts between an overhead shower and a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
2-way ceramic disc diverter with a plastic body, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ceramic disc type float operated inlet valves with DZR brass bodies. The valves discharge from a downwards atmospheric discharge arrangement on the upper part of the body. Maximum working pressure 5.0 bar. For cold water use only.
Range of wall mounted, concealed flow control valves with brass bodies, incorporating either one or two quarter turn ceramic disc headworks with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
‘Europress’ range of in-line pressure reducing valves, with DZR brass bodies and EPDM ‘O’-rings and washer. The outlet pressure is adjustable between 1.0 - 5.5 bar. Operating parameters: 2430012 EUROPRESS model: Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C. 2430034 EUROPRESS & 2430100 EUROPRESS models: Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 99°C.
Range of adjustable pressure reducing valves incorporating a plastic body and EPDM ‘O’-rings and stainless steel strainers. Outlet pressure 1.2 - 8.0 bar. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure relief valves pre-set @ 6.0 bar, incorporating DZR brass bodies, EPDM seal cup and EPDM ‘O’-ring. Maximum operating temperature 99˚C
‘EV220A-W’ range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of lever operating spherical valves incorporating brass bodies, chrome plated brass ball, PTFE seals and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of angled servicing valves with brushed chrome plated DZR brass bodies and ball.The product incorporates a stainless steel strainer and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Spherical valves incorporating bronze bodies with lever operating members, chromium plated brass ball and PTFE seat. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies, brass ball and PTFE seals. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line spherical valve incorporating a nickel plated brass body, chromium plated brass ball, NBR rubber ‘O’-rings and single lever operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies, DZR brass ball (sizes ½” to 1”) and bronze ball (sizes 1 ¼” to 2”) PTFE seats and various operating member types (see models). Maximum working pressure: 25.0 bar. Maximum operating temperature: 85⁰C.
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of gate valves incorporating brass bodies and wedges with EPDM ‘O’-rings and a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated ductile iron disc and EPDM seals. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating brass bodies and wedge with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure 20.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of 115 gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of globe stop valves with a bronze body and disc holder, DZR brass stem and stem ring, PTFE stem gasket and disc. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum operating pressure 20.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of water conditioners incorporating a static PTFE and zinc anode in a brass or nickel plated bronze body. Between November 2021 and December 2023 the maximum working pressure is: ET/ETD models = 10.0bar, EF/EF-16 models = 16.0 bar, EF-40 models = 40.0 bar. From January 2024 the maximum working pressure is: ET/ETD/EF/EF-16 models = 16.0 bar & EF-40 models = 40.0 bar. Maximum operating temperature 60°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of UV disinfection units with stainless steel and EPDM seals. The UV lamps are housed inside synthetic quartz tubes Maximum working pressure 6.9 bar. Cold water use only.
'KOCETAL K100 GMP'. White coloured, extruded acetal material. For use with water up to 85°C.
Hostaform®, injection moulded POM materials. For use with water up to 85°C: Hostaform® Special Grade: M25AE 10-2013 & M25AE 10-2013 ECO-B (black coloured). Hostaform® Glass Bead Filled Grade: C9021 GV3/30 NATURAL. Hostaform® M30RS Natural & M30RS ECO-B NATURAL. For use with water up to 65°C: Hostaform® Unfilled Grades: T1020 NATURAL. Hostaform® Glass Fibre Filled Grades: C9021 GV1/10 NATURAL, C9021 GV1/20 NATURAL, C9021 GV1/30 NATURAL, C9021 GV1/30 3134 NATURAL & C9021 GV1/30 3134 ECO-B NATURAL. Hostaform® Glass Bead Filled Grades: C9021 GV3/10 NATURAL & C9021 GV3/20 NATURAL. Hostaform® Special Grades: M25IE natural, M25IE ECO-B NATURAL & M30AE. Between April 2021 and 2nd August 2022, these grades were for use with water up to 65°C. Between 3rd August 2022 and 30th April 2026, these grades are for use with water up to 85°C: Hostaform® Unfilled Grades: M15HP NATURAL, M15HP ECO-B NATURAL, C2521 NATURAL, C2521 ECO-B NATURAL, C9021, C9021 ECO-B NATURAL, C 9021 ECO-C 872 NATURAL, C13021 NATURAL, C13021 ECO-B NATURAL, C 13021 ECO-C 872 NATURAL, C13031 NATURAL, C13031 ECO-B NATURAL, C 13031 ECO-C 872 NATURAL, C27021 NATURAL, C27021 ECO-B NATURAL & C 27021 ECO-C 872 NATURAL. Hostaform® Lubricated Grades: C9021 M (Natural colour is grey), C9021 M ECO-B NATURAL, C9021 FCT1 NATURAL, C9021 FCT1 ECO-B NATURAL, C9021 TF NATURAL, C9021 TF ECO-B NATURAL, C9021 K NATURAL, C9021 K ECO-B NATURAL, C13021RM NATURAL & C13021RM ECO-B NATURAL. Hostaform® Special Grade: MR130ACS NATURAL & MR130ACS ECO-B NATURAL. These grades were added January 2022. Between January 2022 and 2nd August 2022, these grades were for use with water up to 65°C. Between 3rd August 2022 and 30th April 2026, these grades are for use with water up to 85°C: Tarnoform® 200 CE natural, 300 CE natural, 400 CE natural, 411 CE natural & 500 CE natural. Between April 2021 and xx February 2023, these grades were for use with water up to 65°C. Between 16th February 2023 and 30th April 2026, these grades are for use with water up to 85°C: Hostaform® Unfilled Grades: C 52021 NATURAL & C 52021 ECO-B NATURAL. Tarnoform® 700 CE. Hostaform® Special Grades: C13031 XAS-G NATURAL, C13031 XAS-G ECO-B NATURAL, M25AE NATURAL, M25AE ECO-B NATURAL & HF M25AE ECO-C 872 NATURAL. For use with water up to 65°C: Grade added February 2023: Hostaform® M25AE 10/5358 DW. Grade added April 2025: Hostaform® MR130 ACS 10/5358 DW Black. For use with water up to 85°C: Grade added April 2025: Hostaform® M25AE 10/5358 DW black.
'KEPITAL F20-03 BKM'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'CarSIK-NT'. Grey coloured, RBSiC/SiSiC Reaction Bonded Silicon Carbide washer/seal ring, manufactured by isostatic pressing. For use with water up to 80°C.
`POWLAC EY161`. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions `no. CKP-2015-0172`. Cure for 5 minutes@180°C. For use with water up to 85°C. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Global Smart (INSUPIPE)'. Factory applied, grey coloured cement. Mix cement:sand:water in a 30:55:15 ratio. Cure for 48 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELASTOPOXY PRIMER HP and ELASTOSEAL W Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'ELASTOPOXY PRIMER HP as per Product Data Sheet ‘TSS/TD/280721/C’. Cure for 2 hours@25°C. Then mix and apply ‘ELASTOSEAL W Coating’ as per Product Data Sheet ‘TSS/TDS/260721-B’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Neropoxy Solvent Free Coating White & Red'. Factory applied, white or red coloured, two-component epoxy coating comprising of a base and hardener. Mix base and hardener in a 3:1 mass ratio. Cure for 10 days@28°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 801 Blue 502'. Factory applied, grey coloured modified PE blend coating. Pre-heat part/item to be coated to 340°C, dip into a fluidized bed containing the coating and then allow to cool at room temperature. No cure required For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nu Vista'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours at 45°C and then 28 days (672 hours)@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Infra Pro'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours@45°C and then 28 days (672 hours) @35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'SC2 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-002 issue 1' dated 09-08-2016. For use with water up to 85°C.
'Protecfull SFP 108'. Factory applied, two-component, cream coloured polyurethane coating. Mix part A & part B in a 75:25 volume ratio and apply as per manufacturer's instructions reference '016. Ed.01.21' dated August 24, 2021. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'Rilsan (MagnaCoat 5501 F)'. Factory applied, white coloured (opaque), polyamide powder coating. Apply as per manufacturer's instructions dated 02/01/2018. Cure for 10 minutes@230°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FIBER TECH 80, Low VOC fiberglass resin'. Factory applied, brown coloured polyester resin & fibreglass. Apply as per manufacturer's method statement reference 'PP-GRP-092021-R1' dated '21 Sept. 2020'. Cure for 48 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC1 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-001 issue 1' dated 09-08-2016. For use with water up to 85°C.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
"Bond-It Tanking Slurry". Site applied, grey coloured, two part (powder & water) cementitious waterproof coating. Mix and apply as per manufacturer`s instructions 'Version 9' dated 06/08/20. Cure for 12 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AFM 34/2'. Green/grey coloured fibre gasket material manufactured by calandering. For use with water up to 85°C.
'568H+L101'. Natural (appears off-white in colour), injection moulded GRP material. For use with water up to 70°C.
`8601-A`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Plustek PA303G6BK16'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'TYPLEX-1055'. Grey coloured, extruded Polybutylene-1 material. For use with water up to 85°C.
'XC2'. Black coloured, PEEK washer manufactured by filament winding. For use with water up to 85°C.
'Xytrex 116'. Dark grey coloured, hot compression moulded PEEK washer. For use with water up to 85°C.
‘EURO electrofusion fitting'. Black coloured, injection moulded HDPE electrofusion fitting. For use with water up to 85°C.
'Shield MDPE Fitting'. Black coloured, injection moulded PE80 fitting. For use with water up to 85°C.
'Shield MDPE Pipe'. Black coloured, extruded PE80 pipe. For use with water up to 85°C.
`Comisa' pipe. Triple layered, extruded pipe consisting of a translucent PE-RT inner layer, aluminum middle layer and white coloured PE-LMD outer layer. For use with water up to 85°C.
'+GF+ HAKAN PE-RT White Pipe'. White coloured (opaque), extruded PE-RT pipe. For use with water up to 85°C.
'+GF+ HAKAN PE-XB White Crosslinked Pipe'. White coloured (opaque), extruded PE-XB pipe. For use with water up to 85°C.
'+GF+ HAKAN PE-RT EVOH Pipe'. Extruded pipe with a white coloured (opaque) PE-RT inner layer and an orange coloured EVOH outer layer. For use with water up to 85°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Klimapress Fitting'. Black coloured, injection moulded PPSU fitting. For use with water up to 85°C.
'ROMAKLIMA Pipe'. Extruded, triple layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R (with glass fibre) middle layer and green coloured PP-R outer layer (with dark green stripes). For use with water up to 85°C.
'Romafaser CT pipe'. Extruded, triple layered pipe comprising of a green coloured PP-RCT inner layer, green coloured PP-RCT (with glass fibre) middle layer and green coloured PP-RCT outer layer. For use with water up to 85°C.
`PPR 001` Pipes. White (with red external stripe) or tangerine coloured, extruded polypropylene pipes. For use with water up to 85°C.
'Q-Therm'. Extruded, multi-layered PP-R CT pipe comprising of a green coloured PPR inner layer, translucent PPR/glass fibre middle layer and green coloured PPR outer later. For use with water up to 85°C.
'+GF+ Aquasystem PP-RCT'. Extruded, green coloured (with yellow external stripe), multi-layered pipe. All three layers of the pipe are green coloured and made from PP-RCT but the middle layer also has glass fibres. For use with water up to 85°C.
'F420B00 natural (appears off-white), F420B99 (black coloured) & F410K01 (white coloured)'. Injection moulded, glass filled polypropylene materials. For use with water up to 85°C.
'Xytrex 115'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
'Xytrex 120'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
`FORWA PTFE tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Hepworth CPVC Pipe'. Grey coloured, extruded CPVC pipe. For use with water up to 85°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP7008S 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 60°C.
'EP1/1/6 BLK' O-rings. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.75mm. For use with water up to 85°C.
'EP906'. Black coloured, extruded EPDM washer. Shore hardness 90. Tested in-radius size 1.4mm. For use with water up to 85°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
'CEW50, CEW55, CEW60, CEW65, CEW70, CEW75, CEW80, CEW85 & CEW88'. Black coloured, transfer moulded EPDM rubber materials. Shore hardness between 50 & 88. Tested in-radius size 1.15mm. For use with water up to 60°C.
'CVE45, CVE48, CVE50, CVE52, CVE55, CVE60, CVE61, CVE65, CVE69, CVE70, CVE75, CVE78 & CVE80'. Black coloured, extruded, EPDM materials. Shore hardness between 45 & 80. Tested in-radius size 1.5mm. For use with water up to 60°C.
‘AquaFlex® T 5818’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 65°C.
'AquaFlex T 5817'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 65°C.
'E0265'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. Between September 2021 and 3rd August 2022, the material was for use with water up to 23°C. Between 4th August 2022 and September 2026, the material is for use with water up to 50°C
'PERTEC UP FKM 70.501-07'. Black coloured, injection moulded FKM material. Shore hardness 70. Tested in-radius size 1.01mm. For use with water up to 85°C.
'581189 Center Jet Blue Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Mega All White'. White coloured (opaque) anaerobic sealant/adhesive. Apply in strict accordance with manufacturer's instructions 'issue 01' dated '09/09/2021'. For use with water up to 85°C.
'K.O.T Tape White coloured PTFE Tape'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
Range of float operated valves with plastic bodies and either brass or plastic inlet tails of the side or bottom entry type manufactured to BS1212 Part 3 1990. The valves have ½’’ BSP inlets with plastic backnuts, an up and over type outlet discharge and a plastic operating lever adjusted by a screw & lock nut. Maximum working pressure 14.0 bar. For cold water use only.
Range of BS1212 Part 3 1990 float operated valves incorporating plastic bodies of either the side or bottom entry type. Maximum working pressure 14.0 bar. For cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout has a waterfall outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of fittings for use with cisterns storing wholesome water. Consisting of screened tank overflows, a screened tank breather, two-way expansion pipe tee piece, tank lid adaptor and tank connections. Where products are screened they comprise of a stainless steel mesh. Maximum operating temperature 70°C.
Range of ceramic cartridge headworks with plastic bodies and EDPM ‘O’-rings and gaskets. The products are intended for insertion into specifically dimensioned tap bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Self closing press headwork cartridge with brass body and EPDM ‘O’-rings and NBR gasket, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-rising spindle headwork incorporating a brass body and NBR ‘O’-rings to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating members and pull-down spray handset. The spout outlet incorporates a plastic aerator. The product is supplied with a metal backnut. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener. The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever operated pop-up waste or click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a pop-up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some products are supplied with a pop-up waste or a click type waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 100 xxx model is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet has a plastic aerator and model 31 531 XXX is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated) incorporating a joystick controlled ceramic cartridge headwork. The spout outlets incorporate a plastic aerator. Models 39 031 xxx & 39 035 xxx are supplied with lever operated pop-up wastes and model 39 032 xx is supplied with a pop-up waste kit. Maximum working pressure: 10.0 bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly with brass body (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet (activated by pulling the end of the spout surround). The shower outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The product is also supplied with shower hose and shower handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (stainless steel – various finishes). The flow of hot and cold water is controlled by a ceramic cartridge headwork with a single lever operating member. The flow of near-boiling water is controlled by a ceramic disc headwork, with spring loaded single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 96°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies with various finishes - see model), incorporating either quarter turn ceramic disc or ceramic cartridge headworks with either a wheel type or single lever operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated). Incorporating quarter turn ceramic disc headworks with single lever operating members (model 922069) and non-rising spindle headwork with dome type operating members (model 922039. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. (Model 922041 incorporates a non-rising spindle headworks with dome type operating members) The spout outlets incorporate either a plastic flow straightener or aerator depending on model. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of two hole wall mounted, single outlet (fixed) combination tap assemblies consisting of a concealed brass alloy body incorporating a ceramic cartridge headwork and a chrome finish set (external part) comprising of a face plate, dome type operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed brass body, and a separate trim set (brass body - various finishes), incorporating a ceramic cartridge headwork with a joystick type operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted two-hole, single outlet (fixed) combination tap assembly with a brass body (chrome trim set) incorporating a ceramic cartridge headwork and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets are a waterfall type incorporating a stainless steel strainer. The products are supplied with plastic or brass backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlets are a waterfall type incorporating a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks or a ceramic cartridge headwork (SH-T8025A model only) with various operating members (see models). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with various operating members (see models). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks or a ceramic cartridge headwork (SH-T8025N model only) with various operating members (see models). The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), Models 49723, 26684 & 18193 incorporate a non rising spindle headwork with dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (brass body with various finishes - see model), incorporating a 2 way ceramic disc diverter headwork controlling the flow between the spout or shower outlet with a single lever operating member. Temperature is controlled independently via a thermostatic mixing valve incorporating a single lever operating member with a manual override button. Each inlet incorporates an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum working temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks with either single lever or cross top (SH-T8181 model only) operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks various operating members (see models) and a manual diverter to shower outlet. The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with either single lever or dome type (SH-T8062 model only) operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlets are a waterfall type incorporating a stainless steel strainer. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate either a plastic flow straightener or plastic aerator (SH-T9071 model only). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of floor mounted, two-hole, single outlet (swivel) combination tap assemblies (stainless steel and brass bodies various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
Range of two hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated). Incorporating non-rising spindle headworks with dome type operating members (model 922040) and ceramic disc headwork with single lever operating members (model 922075). The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator (except Broadway and Niagara spout options). The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The spout junction of the Malmaison and Niagara spout options incorporates a plastic flow regulator. The product is also supplied with either a click type or pop-up waste (see model), and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator. The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The product is also supplied with a pop-up waste, and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass spout and trim set), incorporating quarter turn ceramic disc headworks with dome type operating members. The inlet of the spout incorporates a plastic flow regulator, and the spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet, (fixed) combination tap assemblies with brass bodies (chromium plated), incorporating quarter turn ceramic disc headworks with dome type operating members. The product is supplied with stainless steel braided PEX lined flexible hose assemblies for connecting the side body headworks and the spout junction. The spout inlet incorporates a plastic flow restrictor, and the spout outlet incorporates plastic aerator. The products are supplied with click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (various finishes, see models) incorporating quarter turn ceramic disc headworks with wheel type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spout outlets incorporating stainless steel bodies (various finishes) and a plastic aerator. Maximum operating temperature 60°C.
Range of wall mounted spout outlets incorporating brass bodies (various finishes) & plastic aerators. Maximum operating temperature 60°C.
Spout outlet with a brass body (chrome plated). The spout outlet incorporates a combined plastic flow regulator and aerator. Maximum operating temperature 60°C.
Wall mounted waterfall, bath spout (chromium plated brass), incorporating a flow regulator on the inlet and stainless-steel strainer at the spout outlet. Maximum operating temperature 80°C. Open outlet use only
Range of wall mounted spout outlets, (brass bodies with various finishes) incorporating a plastic aerator. Maximum operating temperature: 60°C
Range of filling loop assemblies consisting of an in-line isolation valve, in-line double check valve assembly which also incorporates an isolation valve (suitable for back flow protection against fluid category 3) and stainless steel braided EPDM lined hose. The isolation valves are operated via a single lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Profine’ plastic bodied filter head incorporating EPDM ‘O’-rings for use with filter cartridges (not supplied).For use with LLDPE tube (manufactured to DIN 8072). All models can be specified with or without an integral bracket. Maximum working pressure 6.0 bar. Cold water use only.
Range of carbon block water filters and housings. Maximum working pressure 10.5 bar. Cold water use only.
Range of water filter housings with plastic heads and bodies (various colours - see model), incorporating NBR ‘O’-rings (158087/088/207/208/218/219/261 models only) or with EPDM ‘O’-rings (all other models). Big Blue for Cartridges - Maximum working pressure 6.9 bar (10” filter housings) and 6.2 bar (20” filter housings). Maximum working temp 38°C. All other models - Maximum working pressure 8.62 bar. Maximum working temp 52°C.
Range of inline water filter cartridges with polypropylene housing with a carbon block filter. Maximum working pressure 8.5 Bar Cold water use only.
Carbon block filter cartridge with plastic body. The cartridge may be installed with a manifold (filter head) for use with PE tubing manufactured to BS 1972. Maximum working pressure 8.6 bar. Cold water use only
Range of brass, chrome plated brass or DZR brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of M type press fittings with TP2 copper bodies and EPDM ‘O’-rings, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of urinal flushing mechanisms with a solenoid valve controlling the flow. The valves are controlled via an infra-red sensor. The inlet incorporates a stainless steel strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
A range of under sink electrically heated vented water heaters (cased and insulated) with a stainless-steel cylinder incorporating a temperature sensor and a float switch (not flow control) Maximum operating temperature 98°C.
Range of commercial air or liquid cooled ice making machines with flow controlled via solenoid valve. Maximum working pressure 7.8 Bar. Cold water use only.
‘Aquila V4 C1’ range of water meters (brass or bronze bodies) with a plastic working chamber, flow regulator and impellor, and either NBR or EPDM ‘O’-rings. The products are supplied with loose NBR/fibre flange gaskets. Maximum working pressure 16.0 bar. Cold water use only.
A range of water meters incorporating brass or plastic bodies (See models), EDPM ‘O’-rings, plastic strainer on the inlet and a plastic impellor. Maximum working pressure 16.0 bar. Maximum working temperature 85°C (brass bodies) or cold water use only (plastic bodies)
Range of meter boxes incorporating a plastic manifold arrangement consisting of a stop valve with non-rising spindle , check valve (however the complete assembly has not been tested to demonstrate it provides adequate backflow) and concentric meter port. Some models incorporate a drain off or blacking plug. Connections can be compression or push fit (see model). For use with PE8-0 pipe to BS EN 12201 and copper to EN 1057. Maximum working pressure 16.0 bar. Cold water use only.
Copper corrugated hose. Maximum working pressure 10.0 bar. Maximum working temperature 90°C.
Range of pushfit hose connectors with either plastic (white or black) or chrome plated brass bodies and EPDM ‘O’-rings. SHCV prefix models incorporate screwdriver operated servicing valves. All pushfit connections are for use with PEX pipe (manufactured to BS7291-3) and copper pipe (manufactured to EN1057). Barbed end connections are not approved for use with any hose. Chrome plated brass body models are also for use with PB pipe (manufactured to BS7291-2). Maximum working pressure 10.0 bar (servicing valve models only). Barbed end connections are open outlet use only. Cold water use only.
Range of water hammer arrestor’s incorporating brass bodies (various finishes). The 525152 model is supplied with a reinforced captive nut. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C. For products manufactured from June 2023 Maximum operating temperature 85°C
Range of flow control valves for domestic hot water with plastic bodies and EPDM ‘O’-rings The products incorporate a motor which adjusts the flow, a flow sensor which measures the flow rate and a plastic filter on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pressure gauge with brass body and a plastic case. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C
Chrome plated brass quick connector with EPDM washer. Maximum operating temperature 60°C.
‘Para Z’ range of circulating pumps with either stainless steel, bronze or plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘e-SH’ range of centrifugal booster pumps with a blue polymer coated stainless steel body, stainless steel impeller and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Cold water use only.
Range of overhead shower outlets with chromium plated plastic bodies incorporating stainless steel strainers on the inlets. Models 26 724 xxx & 26 727 xxx incorporate a plastic flow regulator on the inlet. Maximum operating temperature 60°C.
Range of overhead shower outlets incorporating a stainless steel body (various finishes), strainer and flow regulator on the inlets. Maximum operating temperature 60°C.
Range of shower heads with plastic bodies and a brass inlet connection. The inlet of the shower head incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 70°C.
Shower handset with a plastic body (various finishes - see model). Maximum operating temperature 60°C.
Shower handset with a plastic body in a variety of finishes (see model). The inlet incorporates a combined EPDM washer and stainless-steel strainer, and a plastic flow regulator. Maximum operating temperature 60°C.
Range of wall mounted and overhead shower outlets, incorporating stainless steel strainers and flow regulators at the inlets. Maximum operating temperature 60°C
Range of shower handsets incorporating plastic bodies (various finishes), plastic flow regulators and stainless steel strainers. Maximum operating temperature 60°C.
Range of shower kits, shower outlets and shower hoses. The shower handsets and overhead shower inlets incorporate a plastic flow regulator. Maximum operating temperature 45°C.
Shower handset with a plastic body in a variety of finishes (see model). The inlet incorporates a combined EPDM washer and stainless-steel strainer, and a plastic flow regulator. Maximum operating temperature 60°C.
Shower kit consisting of a wall mounted elbow (brass body various finishes - see model), shower hose and handset. The outlet of the wall elbow incorporates a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The shower handset inlet incorporates a stainless-steel strainer and a plastic flow regulator. Maximum operating temperature 60°C.
Range of shower outlets and shower handsets. The shower heads have a brass body and ball joint, NBR ‘O’-ring, stainless-steel strainer and silicon nozzles. The shower handset has a brass body, NBR ‘O’-rings, silicon nozzles and incorporate a plastic flow regulator on the inlet. Model ‘100274774 N200000068’ is supplied with a double interlocked hose and a single check valve cartridge (to be installed on the inlet to the hose) however the complete product has not been fully tested to demonstrate it provides backflow protection. Model ‘100274774 N200000068’ has a maximum operating temperature of 60°C. All other models have a maximum operating temperature of 85°C.
Range of shower outlets with chromium plated bodies. Maximum operating temperature 70°C. Open outlet use only.
Range of shower columns with chromium plated brass bodies. Maximum operating temperature 60°C.
Range of shower handsets plastic bodies (various finishes) and EPDM ‘O’-rings. All models include a button on the shower face which alters the spray pattern. The product incorporates either a plastic strainer (26 050 & 26 530) or a stainless-steel strainer and a plastic flow regulator (26 051 & 26 531) on the inlet. Maximum operating temperature 60°C.
Range of bib taps with (chrome plated) brass bodies, brass ball spherical valve with PTFE seals and a single lever operating member. The spout outlet incorporates a hose union spigot connection. Maximum working pressure 10.0 Bar Maximum operating temperature 85°C
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps incorporating either stainless steel or brass bodies (various finishes), quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The RB3 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Shower hose incorporating a chrome plated stainless steel interlocked casing and a PEX liner. The product is supplied with EPDM gaskets (both models) and ‘O’-rings (MS-PEX-02) model only - M15 end). The product is available in lengths from 300mm-3000mm. Maximum operating temperature 85°C.
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
Range of indirect and direct unvented storage cylinders consisting of either no coil (GLE) or a factory fitted single (GLC) or twin coil (GLT). The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@85˚C for 1.0-6.0 bar products and 10.5 bar@95°C for 6.0-10.0 bar products. The products are supplied with an inlet control group (safety kit) consisting of a pressure reducing valve, an expansion relief valve 6.0 bar (1.0-6.0 bar products) or 10.5 bar (6.0-10.0 bar products) and an approved check valve, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is also supplied with an expansion vessel. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of manually operated, wall mounted, concealed blending valves with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of manually operated, wall mounted, concealed blending valves with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and self-cancelling diverter. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of adjustable T-type thermostatic mixing valves with brass bodies (chrome plated). Each inlet incorporates a stainless steel strainer and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, concealed, thermostatic shower valves with brass bodies and trim sets (various finishes - see models). Flow is controlled as follows (for operating members - see model): Single outlet models: ¼ turn ceramic disc headwork. Double Outlet Models without diverter: ¼ turn ceramic disc headworks. Double Outlet Models with diverter: 2-way ceramic disc diverter headwork. Triple Outlet Models with diverter: ¼ turn ceramic disc headwork and a 2-way ceramic disc diverter headwork. The temperature is controlled independently via a thermostatic cartridge with various operating members (see model) which incorporates a manual override button. The inlets incorporate a single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Specific models are supplied with a shower hose and handset (see models). Maximum working pressure 5.0 Bar Maximum operating temperature 60°C
Wall mounted, exposed thermostatic shower valve (chromium plated brass) incorporating a thermostatic cartridge that controls the temperature and a shut off valve that controls the flow both with a single lever operating member. The inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘Keraflo Aylesbury’ ceramic disc operated inlet valves with DZR brass bodies and ABS or copper outlets. K and KAX type float mechanism incorporate a polyethylene float and spirit level for installation. The KB type float mechanism is operated by a transfer of weight within the actuator tube, which is connected to a polyethylene buoy and weight via stainless steel chain. Maximum working pressure 10.0 bar. Cold water use only.
Range of non return valves incorporating bronze bodies and discs, and PTFE washer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of 5 way inlet control group assembly incorporating a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range of either 3.0 bar, 3.5 bar, or 6.0 bar and a safety relief valve set at either 6.0 bar or 8.0bar (depending on model). The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C
Range of adjustable, pilot operated, pressure reducing control valves with black plastic bodies, EPDM diaphragm, EPDM ‘O’-rings and NBR seals. The products are supplied with auxiliary stainless-steel tubing, lever operated spherical valves, integral stainless-steel strainer, pilot valve and a quarter turn ceramic disc valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 0 - 8.5 bar, 7.0 - 13.5 bar or 12.0 - 16.0 bar (see model). Maximum operating temperature 60°C.
Range of pre-set, spring loaded, angled pressure relief valves with plastic body and EPDM diaphragm. The valves are fitted with rotary type easing gear . For maximum working pressure please refer to model. Maximum operating temperature 99°C.
Range of pre-set pressure relief valves with bronze bodies and EPDM seating discs. Available with either a manual lever or dome type sealed cap. Pre-set relief pressures: DN15 and DN40 valves: 0.35 bar to 15.9 bar. DN20 valves: 0.35bar to 13.8bar. DN25, DN32 and DN50 valves: 0.35 bar to 12.5 bar. Maximum operating temperature 85°C.
Range of servicing valves incorporating brass bodies (chrome plated or natural brass) The P2290 & P2290SI models are spherical valves with brass balls. The 201210 A-80 model is quarter turn with an EPDM seat and ‘O’-ring. The NF721 & NF721SI models are quarter turn with a NBR seat and EPDM ‘O’-ring. The 00711 A-80 is quarter turn with a NBR seat and ‘O’-rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating bronze bodies, wedges and a non-rising stem. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of 5 way inlet control group assemblies with a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range between 2.7 and 3.3bar and a safety relief valve set at 8.0 bar. The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2) and strainer on the inlet Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C
Range of cold water inlet control groups with DZR brass bodies, consisting of a pressure reducing valve, (all models are adjustable between 1.0 and 6.0 bar, but some come pre-set from the factory - see model), a pressure relief valve (set at 6.0 or 8.0 bar - see model) and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The pressure relief valve is fitted with a rotary type easing gear. All products for use with copper pipe manufactured to BS EN 1057. Maximum inlet supply pressure 20.0 bar. Cold water use only.
Range of commercial front loading, hood type & utensil washer type dishwashing machines with flow controlled by solenoid and discharged via type AB air gap (verified by test - suitable for backflow protection against fluid category 5) . The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of electrolytic water conditioners, with a brass body and zinc alloy anodes. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.
Injection moulded POM materials. 'POMM90-BK02' is black coloured and for use with water up to 60°C. ‘POMM90-GR05 & POMM90-GR37’ are grey coloured and were added to the approval in November 2022, they are for use with water up to 85°C.
'SC35'. Grey coloured, SiC washer manufactured by pressing, firing and finishing. For use with water up to 85°C.
'PS5000 Seal'. Grey coloured, compression moulded silicon carbide seal. For use with water up to 85°C.
'Rapox Brown 4 Washer'. Brown coloured, dry pressed ceramic washer. For use with water up to 85°C.
'SYAL B950' (brown coloured) & 'SYAL A950' (white coloured). Dry press moulded ceramic materials. For use with water up to 85°C.
'42.5 (HSR)'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DAT-01'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 34.4:44.9:20.7. Cure for 8 hours@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kerjiwal SRC'. Factory applied, grey coloured Sulphate Resisting Cement. Mix cement, sand & water in a volume ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Orgal® Hydroflex 10'. White coloured, acrylic polymer emulsion cement modifier, which is a liquid additive intended to be mixed with cement to achieve a coating. Mix cement:additive:water in a 197.5:30:10 mass ratio and apply as per manufacturer's instructions '2/18'. Cure for 28 days@23°C and @50% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tesnit BA-60'. Orange coloured aramid fibre/NBR gasket material. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
`Novapress 260`. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'TUCAI WRAS EPDM hose'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 0.68mm. For use with water up to 70°C.
'CELANYL A2 WR GF30 NC 1102/2A & CELANYL A2 WR GF30 NC 1102/2B'. Off-white, injection moulded nylon materials. For use with water up to 85°C.
'Badadur PBT8 GK30 Graphit 371'. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'Avaspire AV-621 NT'. Natural (appears beige, opaque), injection moulded PEEK material. For use with water up to 85°C.
'VICTREX' injection moulded PEEK thermoplastic materials. For use with water up to 85°C. VICTREX PEEK 450GL30, 450G, 450FE20 (natural – appears beige coloured), 450FC30, 450CA30 & 90GL30BLK-EU (black coloured). VICTREX FG™100, FG™120, FG™200, FG™220, FG™300 & FG™ 325 (natural – appears beige coloured). VICTREX FG™101, FG™121, FG™140, FG™201, FG™221, FG™240, FG™301 & FG™320 (black coloured). VICTREX FG™340 (dark grey coloured).
'Lucite Diakon ST25G8 Clear 0003'. Colourless, injection moulded PMMA material. For use with water up to 23°C.
'PlastFast/Plast Electrofusion Fittings'. Black coloured, injection moulded HDPE electrofusion fittings. For use with water up to 85°C.
'Uponor Combi Pipe'. Multi-layered, extruded PEX pipe comprising of an uncoloured (translucent) inner layer, uncoloured EVOH middle layer and white coloured outer layer. For use with water up to 85°C.
`HYDROFAS'. Black coloured, extruded polyethylene (PE 80) pipe. For use with water up to 23°C.
'Total 3581 Blue Polyethylene & Total 3581 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'RavaRoto 3850UV black & RavaRoto 3930UV black'. Black coloured LLDPE materials manufactured by rotational moulding. For use with water up to 23°C.
'RavaRoto 3850UV natural & RavaRoto 3930UV natural'. Natural (appear white) LLDPE materials manufactured by rotational moulding. For use with water up to 23°C.
'TORELINA A673MWRB'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'ALMATHERM PPR Pipe'. Green coloured, extruded polypropylene pipe. For use with water up to 85°C.
'T-Mech PP-R Multilayer Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-R inner layer, black coloured PP-R/glass fibre middle later and green coloured PP-R outer layer. For use with water up to 85°C.
`PM PTFE tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
`DCOTA Seal tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
`ONDA Seal tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
'G400 & G400B' seat components. White coloured, extruded PTFE seat components. For use with water up to 85°C.
'KLINGER® top-chem 2000'. Grey coloured, SiC filled PTFE material manufactured by calendaring. For use with water up to 85°C.
'AQUAPEA® In-line Repair'. Site applied, dark grey coloured (once mixed), two-part epoxy putty (light grey and dark grey coloured) and polypropylene core (white, translucent). Mix & cure as per the document: “Aquapea method statement issue 1 dated 23-04-21” . For use with water up to 23°C.
'EX1'. Site applied, grey coloured (once mixed), two-component anchor resin. Mix, apply and cure as per manufacturer's product information 'EX1 V2.08' Issued '08/2021' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
`RG EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'SEAEP80N01'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'E8121'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'4273 'O' rings and washers'. Black coloured, injection moulded EPDM 'O' rings and washers. Shore hardness 70. The 'O' rings have an in-radius size of 1.31mm. The washers have an in-radius size of 2.00mm. For use with water up to 85°C.
'S-9028'. Black coloured, compression moulded EPDM rubber material Shore hardness 60 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EBW-65'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.98mm. For use with water up to 85°C.
'S/EP-50, S/EP-60, S/EP-70 & S/EP-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50A & 80A. Tested in-radius size 1.05mm. For use with water up to 65°C.
'ILPEA 70-90 EPDM COMPOUND WRAS AF'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.25mm. For use with water up to 23°C.
'EPDM-W E267'. Black coloured, compression moulded EPDM material. Shore hardness 80A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'70NBR103F'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TEC S147 R.-45 ROSSO'. Orange coloured, injection moulded, silicone rubber 'O' rings & gaskets. Shore hardness 45. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'Silicone LSR2090-50'. Colourless (translucent), injection moulded silicone rubber material. Shore hardness 50. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 85°C.
'SB1 Bonding Agent'. Factory applied, black coloured bonding agent intended to bond plastic or brass to rubber. Apply and cure as per manufacturer's instructions 'LDAP-003 issue 1' dated 11-08-2016. For use with water up to 85°C.
'D77 Nut Grade Adhesive & D377 Thread Sealant'. Site applied, green coloured anaerobic adhesives. Apply and cure as per manufacturer's instructions. D77 is for use with water up to 85°C. D377 is for use with water up to 23°C.
'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ixef DW 1022 BK001 & Ixef FC-1022 BK001'. Black coloured, injection moulded polyarylamide materials. For use with water up to 85°C.
'DESTONE DSC7500G6'. Black coloured, injection moulded polyketone material. For use with water up to 85°C.
'ULTEM', injection moulded polyetherimide materials. For use with water up to 85°C. PW1000-1000, PW1000-1000 and PW1000-1000W (yellow coloured). PW2100-1000, PW2100-1000 and PW2100-1000W (brown coloured). PW2200-1000 & PW2300-1000 (beige coloured). PW2400-1000 (grey coloured). PW1000-7101, PW2100-7301, PW2100-7301, PW2100-7301W, PW2200-7301, PW2300-7301 & PW2400-7301 (black coloured). ULTEM PW2300-1000 and ULTEM PW2300-1000W were added to the approval in June 2025.
'Hytrel® HTR6108'. Translucent cream coloured, injection moulded thermoplastic elastomeric material. Shore hardness 61. For use with water up to 85°C.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Non-verifiable single check valve assembly consisting of a spring loaded, resilient trim, single check valve cartridge with a brushed chrome DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Non- verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a chrome plated DZR brass body with an integral insolation valve between the cartridges. For use with copper pipes to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chrome plated or brass finish) with a port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating NBR ‘O’ rings and silicone seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and cartridge headworks with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of quarter turn ceramic disc headworks with metal bodies to be inserted in specifically dimensioned bodies. Maximum working pressure 17.0 bar. Maximum operating temperature 85°C.
Range of headwork assemblies with brass bodies incorporating a quarter turn ceramic disc headwork. Maximum working pressure 17.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies (various finishes on the stem), silicone seals, and EPDM ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone gaskets. The products are intended for insertion into specifically dimensioned tap bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating brass bodies (GH25W, GH35W) or plastic body (GH35T), and NBR ‘O’-rings. For insertion into specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of single hole single outlet fixed combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headworks with single lever operating members. The product incorporates a plastic flow regulator in the spout body, and a plastic aerator in the spout outlet. Certain models are supplied with click type waste (See models). Maximum working pressure 10 bar. Maximum working temperature 60 °C.
Wall mounted single-hole, single outlet, fixed, combination tap assembly with a brass body in a variety of finishes (See models). Incorporating a ceramic disc headwork with a dome type operating member. The temperature is controlled separately via a rotary ceramic cartridge headwork that can also be used as a shut off with a dome type operating member. The inlets to the tap incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and plastic flow regulator. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators. The 31 609 xxx model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (AX-MAT-137-CP) or plastic aerator (AX-ROW-137-CP). The product is supplied with metal back nuts. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. To be used with rough set 13622180. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of concealed two hole, single outlet (fixed) wall mounted tap assemblies, with a brass bodies and chrome plated trim set. Consisting of a rough in set 63397 and external trim 65088 and 65089. Incorproating a ceramic cartridge headworks and single lever operating members.The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members or non-rising spindle headworks with dome type operating members (922036 model only) and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The 922308 and 922317 models are also supplied with an optional plastic aerator. The products are supplied with a shower hose and handset and metal back nuts. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset and metal back nuts. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly with brass body (various finishes). Incorporating quarter turn ceramic disc headworks, and self cancelling diverter to shower outlet. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with various operating members (see models). The products are supplied with two stainless steel braided EPDM lined flexible hose assemblies with ½” captive nut end connections for installation between the side valves and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The product is supplied with stainless steel braided PEX lined flexible hose assemblies with M8 x ⅜” captive nut end connections and a combined NBR washer and stainless steel strainer (x2) for installation between the side valves and the brass tee piece to the spout. The inlets of the brass tee piece incorporate an approved single check cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with two loose fibre gaskets for installation on each inelt hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C
Range of three hole, single outlet (fixed) wall mounted, concealed tap assemblies with brass bodies and chrome plated trim set. Consisting of a rough in set 45089 and extermnal trim 65090 and 65091. Incorproating a quarter turn ceramic disc headworks and single lever operating members.The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Four-hole, single outlet (fixed) combination tap assembly (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members. interconnecting flexible hoses. The spout outlet incorporates a self-cancelling diverter to the shower outlet and a plastic flow straightener with stainless steel mesh strainer. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members. interconnecting flexible hoses. The spout outlets incorporate a self-cancelling diverter to the shower outlet and a plastic flow straightener with a stainless-steel mesh strainer. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members. interconnecting flexible hoses. The spout outlets incorporate a self-cancelling diverter to shower outlet and a plastic flow straightener with stainless steel mesh. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
A range of four-hole single outlet fixed combination tap assemblies with brass bodies in a variety of finishes (See models). Incorporating ¼ ceramic disc headworks with single lever operating members and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet elbow incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is supplied with a shower hose, shower handset and metal screw clamp type back nuts. The side valves and the spout are connected with a copper tube. Maximum working pressure 10 bar. Maximum working temperature 60 °C.
‘CD3 Series’ chlorine dioxide dosing system incorporating a single check valve positioned at the point of injection. Maximum working pressure 6.0 bar. Cold water use only.
Range of expansion vessels with EPDM membrane and stainless steel flange connections. Models VB8, VB12, VB18 & VB24 have a maximum working pressure of 16.0 bar. All other models have a maximum working pressure of 10.0 bar. Maximum operating temperature 100°C.
Range of filling loop assemblies, comprising of a stainless steel braided EPDM lined hose, isolation valve with a DZR brass body and ball and an isolation valve with a DZR brass body and ball incorporating two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). The F1400120012211 model has an isolation valve incorporating two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3) at each end of the filling loop. All items except the hoses are nickel plated. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Carbon block filter cartridge with plastic body. The cartridge may be installed with a manifold (filter head) for use with PE tubing manufactured to BS 1972. Maximum working pressure 8.6 bar. Cold water use only
‘Comisa’ range of brass bodied press-fit and threaded fittings for use with `Comisa’ (PE-RT/AL/PE-LMD) multi-layer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper press fittings with EPDM seals for use with EN1057 copper tube. The joints are achieved by means of a press tool. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Boss Range of brass, chrome plated brass or DZR brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass tee fittings for use with copper pipe to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of end feed copper solder fittings for use with copper tube. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both domestic hot water and primary are controlled via spherical valves. The primary circuit has a maximum working pressure of 2.5 bar. The secondary circuit has maximum working pressure of 10.0 bar. Maximum supply temperature is 60°C. Maximum operating temperature of secondary circuit is 85°C.
Range of floor standing gas fired combination boilers providing domestic hot water via a stainless-steel plate heat exchanger. Unit is supplied with a safety relief valve (8.0 bar). Maximum working pressure 7.5 bar. Maximum operating temperature 85°C.
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressure relief valve set at 3.0 bar. The supplies to both primary hot water and secondary are controlled via spherical valves. The boilers incorporate a filling loop assembly which incorporates a double check valve assembly (suitable for backflow protection against Fluid Category 3). Primary circuit: Maximum working pressure 2.5 bar. Maximum operating temperature 82°C. Secondary circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of floor standing gas fired combination boilers providing domestic hot water via a stainless-steel plate heat exchanger. Unit is supplied with a safety relief valve (8.0 bar). Maximum working pressure 7.5 bar. Maximum operating temperature 85°C.
Hydraulic block assembly comprising a flow sensor, primary pump assembly, pressure relief valve preset at 3.0 bar and plate heat exchanger. Maximum working pressures: secondary = 10.0 bar and primary = 2.5 bar. Maximum operating temperature 80°C.
Aquila V5 range of water meters with black epoxy coated cast iron bodies, plastic turbines, fibre/NBR flange gaskets and either NBR or EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with blue epoxy coated iron bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
MJ (Multi jet) range of water meters with either ductile iron (MJF model) or brass (MJ models) blue epoxy coated bodies and EPDM rubber ‘O’-rings. Maximum working pressure16.0 bar. Maximum operating temperature 85°C.
External pump docking station with a plastic body and NBR ‘O’ rings. Cold water use only.
Range of radial flowmeters incorporating EPDM ‘O’-rings. The type 10088400 model has a black plastic body and threaded inlet. The type 10088402 model has a pale olive green plastic body with a threaded brass inlet incorporating a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Plastic bodied flow sensor with silicone gaskets. Maximum working pressure 17.5 bar. Maximum operating temperature 85°C.
Range of in line regulating valves DZR brass bodies, EPDM ‘O’-rings and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Angle bracket with brass body (various finishes). The inlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
‘Showermate Universal’ range of booster pumps with plastic bodies and impellers, stainless steel shafts, brass manifolds, NBR ‘O’-rings and EPDM seals. The product incorporates a pressure vessel. The outlet(s) incorporate(s) an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The inlet hose(s) supplied with this product incorporate(s) an isolation valve. Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.
Shower bracket, incorporating a brass body(various finishes) and EPDM O’-rings. Maximum operating temperature 85°C.
Range of shower outlets: swivel ball joint overhead shower heads with brass bodies (chromium plated) and shower handsets with plastic bodies (chromium plated). The overhead showers incorporate a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Range of ceiling mounted shower outlets. The inlet to the shower head incorporates a combined NBR gasket and stainless steel filter, as well as a plastic flow regulator which is located after an adjustable ball joint. Maximum operating temperature 60°C.
Range of shower handsets (chromium plated) brass bodies and NBR O-rings. The inlets incorporate stainless-steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60ºC
Shower head with white ABS body. Maximum operating temperature; 75°C. Maximum operating pressure; Open outlet use
A range of shower kits and hand showers incorporating metal bodies (chrome plated). Some models are supplied with sliding rails, wall elbows and shower hoses (see models). Maximum working temperature 60°C.
Range of overhead shower outlets with brass bodies in various finishes (See models) incorporating EPDM ‘O’-rings and seals. The inlet to the shower heads incorporate either a plastic steel sieve (26 031 xxx) or a stainless steel (26 032 xxx) has a stainless-steel sieve. The inlet for the shower head incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection (Model 26 031 xxx only). Maximum operating temperature 60°C.
Shower head incorporating a chrome plated plastic body and NBR gasket, Maximum operating temperature 85°C.
Range of plastic shower handsets (various finishes). Maximum operating temperature 75°C.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless steel filter and a plastic flow regulator. Maximum working temperature 60°C.
Range of shower kits, comprosing of shower handset, shower hose, riser rail and overhead shower outlet depending on kit. Inlets incorporate a flow regulator (models 1.1740.578 & 1740.155) Maximum operating temperature 60°C.
Range of overhead showers with brass and plastic bodies (various finishes - see models). The inlet incorporates a stainless-steel strainer and a plastic strainer. Products to be used with basic sets with brass bodies and EPDM O-rings. Open outlet use only
Non-metallic materials and components comply with BS6920 at 60°C
Range of filter type fixed ‘shower’ outlets and shower handsets with plastic bodies. Maximum operating temperature 45°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of flow switches with plastic bodies. The VK308/10/15/20/25/32/40/50M and VKS08/10/15/20/25/32/40/50M prefix models are supplied with an inline brass adaptor. The VK305/306/309M and VKS05/06/09M prefix models are supplied with a brass adaptor for direct insertion into a pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of flow switches incorporating brass or stainless steel bodies. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of flow sensors with brass or plastic bodies. Flow sensor type series VTY10 (plastic body, G3/4): Maximum working pressure 10.0 bar. Maximum operating temperature 85°C. Flow sensor type series VTY10 (plastic body, Quickfasten OD 22.5mm): Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. Flow sensor type series VTY10 (brass body, G1/2): Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of bib taps incorporating either brass or DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of self-closing combination taps with brass bodies (chrome plated), incorporating a non-concussive headwork with dome type operating members. The inlets incorporate an approved single check valve cartridge, however the complete assembly has not been verified to demonstrate it provides backflow protection. The inlets of model 28681 incorporate a stainless-steel filter. The inlets of model 28682 incorporate a servicing valve and stainless-steel filter. The outlets of all models incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
'APL' range of PVC lined flexible hose assemblies with various end connectors. Maximum working pressure 10.0 bar. Cold water use only.
PEX lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
OH Softpex® range of polyethylene lined outlet hoses with stainless steel and polyamide braiding (length 100 to 1000 mm), with various end connections. The hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 65°C.
EPDM lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of free standing direct gas fired unvented cyliners with a enamel coating internal lining and magnesium sacrificial anode. Fitted with a combined temperature and pressure relief valve set at 7 bar. Maximum working pressure 6.5 bar. Maximum operating temperature 80°C.
Range of two, three, four and five-way manifold assemblies incorporating brass bodies (brushed chrome finish) and EPDM ‘O’-rings. The products are supplied with isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of wall mounted, concealed, blending valve, incorporating brass bodies (chrome plated), quarter turn ceramic disc headworks with single lever operating members and a manual diverter diverting the flow to two outlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of concealed, wall mounted, electronically controlled blending valves (brass body). The flow is controlled via a solenoid valve actuated via an infra-red sensor. Inlets to the sensor box incorporate stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Wall mounted, thermostatic shower valve (chromium plated brass). Flow is controlled by a quarter turn ceramic disc headwork with single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a cross-top operating member that incorporates a manual override button. The product is supplied with a shower rail and overhead shower. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Wall mounted bar type thermostatic shower valve, with a ceramic cartridge headwork controlling the flow between overhead shower and handset with a dome type operating member incorporating a manual override button. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a strainer and a single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Supplied with hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of concealed, thermostatic shower blending valves, incorporating a brass body and a (chrome plated) functional trim set. The functional trim set comprises of a quarter turn ceramic disc headwork, or a 2 or 3 way ceramic disc diverter headwork (see model) with a dome type operating member controlling the flow, and a thermostatic cartridge controlling the temperature with a dome type operating member incorporating a manual override button. The functional trim set is also supplied with two brass assemblies comprising of a plastic filter, EPDM ‘O’-rings and an approved check valve cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Thermostatic blending valve (chromium plated brass), the valve body inlets incorporate single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with stainless steel strainers and inlet connections that incorporate screw driver operated spherical valves. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of T-Type thermostatic mixing valves incoporating a brass body and a thermostatic cartridge controlling the temperature. The 15mm & 22mm compression models are for use with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of piston type float operated inlet valves with brass bodies. The valves discharge from a downwards atmospheric discharge arrangement on the underside of the body. Maximum working pressure: 3.0 (1FVA106 & 1FVA104 models only) or 14.0 Bar (all other models) Cold water use only.
Piston type float operated inlet valves with blue epoxy coated ductile iron bodies. The products are supplied with a plastic float and carbon steel (galvanised) lever. The valves discharges from a downwards atmospheric discharge arrangement on the underside of the body. Maximum working pressure 16.0 bar. Cold water use only.
Deck mounted flow control valve incorporating a brass body, quarter turn ceramic disc headwork with circular operating members and EDPM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, flow control valves (brass bodies), incorporating a quarter turn ceramic disc headwork with either a cross top or single lever operating member (see models). The products are supplied with a metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
In-line adjustable pressure reducing valve assembly with a DZR brass body. The assembly also incorporates a stainless strainer (part of the pressure reducing valve), a spherical valve with a brass ball on the inlet, a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) on the outlet, and a drain port with a brass plug. The product also includes a port with a plastic plug to accommodate a gauge/sensor (not supplied). Adjustable outlet pressure range between 1.0 and 6.0 bar. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pre-set, spring loaded, angled pressure relief valves, with a plastic body and EPDM diaphragm. The B312021 CST model only is pre-set at 4.0 bar, all other models are pre-set at 3.0 bar. The valves are fitted with either rotary type easing gear or hand operated lifting gear. Maximum operating temperature 99°C.
Range of latching and non-latching solenoid valves with brass bodies and an integral stainless-steel strainer. X262513141 (abc) (dd) models have a NBR ‘O’-Ring and diaphragm, all other models have an EPDM ‘O’-Ring and diaphragm. Maximum working pressure: see model. Maximum operating temperatures: X262513141(abc)(dd) models 65°C, all other models 85°C.
Range of in-line, “T” type or angled spherical valves incorporating brass bodies and brass ball, EPDM ‘O’-rings/Washers, PTFE seats and single lever or butterfly lever operating members. Some models incorporate port or pressure gauge. Models 0516/03DCVR1, 0516/03DCVR2 & 0516/04TR1 incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressures 10.0 bar Maximum operating temperature 100°C.
Range of brass bodied, straight and angled two and three-port spherical valves. Some models incorporate a screw-down pattern drain valve. Products incorporate a chrome-plated brass ball and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (nickel plated) brass bodies with single lever operating members, (chromium plated) brass ball and PTFE seat. Maximum working pressure 40.0 bar (Models 124-1027 CST, 124-1028 CST and 124-1029 CST) Maximum working pressure 25.0 bar (Models 124-1030 CST and 124-1031 CST) Maximum working pressure 16.0 bar (Models 124-1032 CST and 124-1033 CST) Maximum operating temperature 85°C.
Range of angled isolation ball valves incorporating brushed chrome plated DZR brass bodies, DZR brass ball (chrome plated), stainless steel strainer and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spherical valves incorporating stainless steel strainers, chrome plated brass ball, housed within DZR brass bodies with a brushed chrome finish. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves incorporating brass bodies, NBR, PTFE and fibre seals. For use with copper pipe (EN 1057) Maximum working pressure 16.0 bar. Maximum working temperature 85°C.
Range of gate valves incorporating brass bodies, brass wedge, PTFE and NBR washers and operated via a non-rising spindle headwork. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of angled valves incorporating (chromium plated brass bodies), NBR rubber seals and a dome type operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic circulation valves incorporating brass bodies and EDPM ‘O’-rings. Some models incorporate a gauge port. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Silver and copper disinfection ion generator with a plastic body, incorporating a plastic flow switch. Maximum working pressure 9.0 bar. For cold water use only
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
‘DURACON® M90-57 WK2001 & DURACON® M270-57 WK2001’. Grades 'M90-57 WK2001BG' & 'M270-57 WK2001BG' were added to the approval during September 2022. White coloured, injection moulded POM materials. For use with water up to 85°C.
‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.
'CY25C & MAT4000'. Grey coloured, phenolic impregnated carbon washers. For use with water up to 85°C.
`CY9198`. Grey coloured, pressed and kilned carbon/graphite thrust ring. For use with water up to 85°C.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Rivertex® APO850 Blue & NTP™ E850 0A’ and ‘Rivertex® APO850 Grey & & NTP™ E850 0A '. Polyester fabric (NTP™ E850 0A) completely coated with blue or grey coloured polyolefin (Rivertex®), manufactured by extrusion coating. For use with water up to 23°C.
'novapress® 850'. Light brown coloured, compressed fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘UNITEC® Öko’. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'FlatSeal HMF17'. Light brown coloured, compressed fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘Fybar PT 60' (light green on one side and beige on the other). Fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Unecol Paste Solder Flux'. White coloured paste flux. For use with water up to 85°C.
'Center Soldering Flux Paste'. White coloured paste flux. For use with water up to 85°C.
'DualPac 2212 High Performance Multi-Purpose Packing'. Braided gland packing which is half white coloured and half yellow coloured. For use with water up to 85°C. For use as a gland packing only having been tested at a reduced surface area to volume ratio.
'Keyu Magnet'. Black coloured, pressed and sintered magnets. For use with water up to 85°C.
'Ultramid® B3EG7 black 00564' (Black coloured) & 'Ultramid® B3EG7 uncolored' (appears beige). Injection moulded nylon materials. 'Ultramid® B3EG7 uncolored' is for use with water up to 65°C. 'Ultramid® B3EG7 black 00564' is for use with water up to 85°C.
'EcoPaXX® Q-DWX6 BK00002 & EcoPaXX® Q-DWX10 BK00002’ (black coloured). 'EcoPaXX® Q-DWX6 NA99001 & EcoPaXX® Q-DWX10 NA99001’ (natural – appears beige). Injection moulded polyamide materials. For use with water up to 85°C.
'Retiflex PE-Xb'. Translucent, white coloured, extruded, single-layered PE-Xb tubing. ‘RETIFLEX PEXb black’ was added to the approval in October 2024. Black coloured, extruded, single-layered PE-Xb tubing. Both tubes are for use with water up to 85°C.
'LIC PEX-b'. White (translucent), extruded PEX-b pipe. For use with water up to 85°C.
'PF Press'. Triple layered, extruded pipe comprising of a white coloured (translucent) inner layer, aluminium middle layer and white coloured (opaque) outer layer. For use with water up to 85°C.
'SHK Aqua Fitting'. Green coloured, injection moulded PP-R fitting. For use with water up to 85°C.
'Eurocarboran TIPO A Naturale (132.166.120)'. Natural (appears off-white), injection moulded PP material. For use with water up to 85°C.
'Aidmer78-031'. White coloured (opaque), extruded PTFE pipe. For use with water up to 85°C.
'EP10/00/2 BLK EPDM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 65. Tested in-radius size 1.5mm. For use with water up to 85°C.
'E7053AA'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size between 0.25mm and 5.0mm. For use with water up to 85°C.
Black coloured, compression moulded EPDM components. For use with water up to 85°C. ‘559843, 55985 & 559865’ ‘O’ rings. Shore hardness between 60 & 80. Tested in-radius sizes between 1.31mm & 3.49mm. ‘55985 Gasket’. Shore hardness 70. Tested in-radius size 1.0mm. ‘559865 gasket’. Shore hardness 80. Tested in-radius size 1.50mm. When processing an application for a Product Approval incorporating these components, these are the only shapes of components that are covered by the scope of the approval’.
'Sunaflex T 8289'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'LC 50-90'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
'Sunaflex T 8157'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP50, EP55, EP60, EP65, EP70, EP75 & EP80'. Black coloured, transfer moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius size 1.1mm. For use with water up to 85°C.
'Athena-EPDM-XX70'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'006800.3 washer, 006802.6 washer & 006906.4 slab (made using 7741 compound)'. Red coloured, compression moulded VMQ components. Shore hardness 70. The '006800.3 washer’ has a tested in-radius size of 1.16mm. The ‘006802.6 washer’ has a tested in-radius size of 1.15mm. The ‘006906.4 slab' has a tested in-radius size of 1.17mm. For use with water up 85°C.
'Ixef DW/FC-1022 NT000'. Natural (appears pale grey coloured), injection moulded polyarylamide (manufactured in China & Belgium). For use with water up to 85°C.
'TPE-GB6061G (grey coloured) & TPE-GB6061B (blue coloured)'. Injection moulded TPE materials with a shore hardness of 60. TPE-GB6061G has a tested in-radius size of 1.41mm. TPE-GB6061B has a tested in-radius size of 1.38mm. For use with water up to 75°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (brass body - various finishes, see model). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
A range of wall mounted two hole single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor on the underside of the tap. The inlets of the function block incorporate stainless steel strainers, plastic silencers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a lever operated dual flush syphon with full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres and incorporates a servicing valve and flexible hose on the inlet supply.The cistern is operated by a pnuematic push button Maximum working pressure 10.0 bar. Cold water use only.
DC type pipe interrupter with a permanent atmospheric vent. Chomium plated DZR brass body and shroud. Maximum working pressure 8.0 bar. Maximum operating temperature 40°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies incorporating DZR brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with a drain port located between the cartridges. For use with copper pipe manufactured to BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of ceramic disc diverter cartridges incorporating plastic bodies for use in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Manual click type cartridge headwork with plastic body. EPDM seals and plastic strainer for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
Range of four-hole, single outlet (swivel) combination tap assemblies (brass bodies, chrome plated or brushed steel finish) with a spout outlet and flexible hand spray outlet. The hot water is controlled to the spout outlet only (not to the spray outlet) via a quarter turn ceramic disc headwork with single lever operating member. The cold water to the spout outlet and trigger-operated spray outlet is controlled and diverted via a ceramic disc diverter headwork. The product is supplied with Stainless steel braided EPDM lined flexible hose assemblies for connection between the headworks and spout. The spout outlet incorporates a plastic aerator and the products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The BC428AA and BC430AA models are supplied with a pop-up waste. The products are supplied with loose ⅜” BSP (M) x 15mm compression adaptors for installation on each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating brass bodies (chrome plated) ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, fixed combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator or flow straightener (63446-7001 and 63455-7001 models only). The 63446-7001 model also incorporates a combined EPDM washer and stainless steel strainer on the spout outlet. The inlet hoses incorporate a combiner washer and stainless-steel strainer. The products are supplied with click type pop-up waste. Maximum working pressure 5.0 bar. Maximum working pressure 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products can be supplied with a pop-up or click type waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products can be supplied with waste outlets (see models). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Floor mounted single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout incorporates a plastic flow regulator and the shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is supplied with a shower hose and handset which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a push to open, push to close ‘detent’ headwork and the spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
A range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is also supplied with an alternative spout outlet that incorporates a plastic flow straightener and a stainless-steel strainer. The products are supplied with a loose brass ½” BSP (M) x ½” BSP (F) adaptor for installation on the cold inlet. This adaptor incorporates a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass or stainless steel), comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a dome type or single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. The products are supplied with click type (click clack) waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies with (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet, fixed combination tap assemblies (chrome plated brass), incorporating a single sequential cartridge headwork with a dome type operating member. The spout outlet is connected to the flow control valve via a stainless steel braided PEX lined flexible hose assembly. The spout inlet incorporates a plastic flow regulator, and the spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wall mounted two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a 2 way ceramic disc diverter controlling the flow between the spout outlet and the shower outlets with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The product incorporates a secondary manual diverter to divert the flow between the overhead shower and the shower hose and handset. The spout outlet incorporates a plastic aerator. The inlets and the outlet to the shower handset all incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (brass body with various finishes - see model), incorporating a 2 way ceramic disc diverter headwork controlling the flow between the spout or shower outlet with a single lever operating member. Temperature is controlled independently via a thermostatic mixing valve incorporating a single lever operating member with a manual override button. Each inlet incorporates an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The product is supplied with plastic backnuts. Maximum working pressure 10.0 Bar. Maximum working temperature 60°C.
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is also supplied with an alternative spout outlet that incorporates a plastic flow straightener and a stainless-steel strainer. This product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies incorporating chrome plated brass bodies, quarter turn ceramic disc headwork with lever type operating members. The spout outlets incorporate a plastic aerator. The product is supplied with stainless steel braided PEX lined flexible hose assemblies to connect between the valves and spout Model 23484W-4-CP is supplied with pop up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted three-hole, single outlet (fixed) combination tap assembly with a brass body (chrome plated) incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with various operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic aerators. The products are supplied with a shower hose and metal back nuts. The hose connector incorporates an approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of basin spout outlets with brass bodies (various finishes), the outlet incorporates either a metal aerators, plastic aerators or open outlet (depending on model). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of expansion vessels with EPDM membrane and stainless steel flange connections. Maximum working pressure of 10.0 bar. Maximum operating temperature 100°C.
‘Unidelta Deltapress’ range of brass press-fit fittings for use with ‘Unidelta Flexall’ PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass, chrome plated brass or DZR brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘HE-705X & HE-715X’ ranges of brass crimp fit fittings incorporating EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057-2006). HE-7052/7053/7058/7059 & HE-7152/7153/7158/7159 models also incorporate a NBR gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
VSH XPRESS Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PVC-u solvent weld and threaded union fittings incorporating an EPDM ‘O’-ring. For use with PVC-u pipe manufactured to ISO 1452 and DIN 8063. Maximum working pressure 10.0 bar. Cold water use only.
‘Xpress’ range of press fit fittings with copper or brass bodies and EPDM ‘O’-rings. For use with copper tube manufactured to EN1057. For above ground ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘Endex’ range of copper alloy and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of stainless-steel plate heat exchangers with EPDM gaskets. The primary circuit, (excluding the E2 prefix models), incorporates a drain valve and a pump (excluding STP prefix models including an ‘N’ as the 14th figure). Operating parameters: Maximum working pressure of the secondary circuit: 6.0 bar or 10.0 bar (see model). Maximum working pressure of the primary circuit: E4 models: 6.0 bar. C3, E3, E2, i2: 10.0 bar. Models added February 2023 – Econoplate STP3, STC3, STP2, STC2 & STP4: 10.0 bar. Maximum operating temperature: Primary 140°C & Secondary 85°C.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of gas fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The cold inlet incorporates an angled spherical valve with a brass body, chromium plated brass ball and a lever operating member. The primary circuit incorporates an expansion vessel, isolation valves on flow and return, drain valve and a pressure relief valve set at 3.0 bar. Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature for the secondary circuit is 55˚C. Cold supply only.
Greenstar Heatslave II range of floor standing oil-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system, which incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The cold water inlet incorporates a screwdriver operated spherical valve followed by a plastic flow regulator inserted within the pipework. Maximum working pressure: Primary circuit 2.5 bar. Secondary circuit 10.0 bar. Maximum operating temperature 82°C.
Range of in-line water meters with brass bodies and plastic inlet filters. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C (SJ & ELECTO-SJ models) Maximum operating temperature 30°C (AP VARIO and AP RADIO models)
Y type fittings incorporating brass body and NBR washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pump inverters with plastic bodies, NBR rubber and EPDM rubber seals and ‘O’-rings. The products incorporate an inline resilient trim non-return valve. Maximum working pressure 13.0 bar. Cold water use only.
Range of cold water in tank booster sets incorporating an ‘AG’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.
Range of cold water in tank booster sets incorporating an ‘AB’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.
Range of pumps with stainless steel bodies and plastic impellors. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
‘ECOCIRC XL N’ & ‘ECOCIRC XL PLUS N’ range of circulation pumps with stainless steel bodies, plastic impellers, and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of showers handsets with plastic bodies (various finishes - see model). All models incorporate a stainless steel strainer, the EcoSmart models also incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of shower handsets with brass bodies available in various styles and finishes. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Wall mounted shower head and arm (chromium plated brass) incorporating a NBR seal and TPE gasket. The inlet to the shower head from the shower arm incorporates a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working temperature 60°C.
Range of shower handsets and shower kits. Shower kits 2.1703.391, 2.1703.015 & 2.1703.016 incorporate a shower handset, shower hose and riser rail. Shower handset inlets incorporate a flow regulator. Maximum operating temperature 60°C.
Range of shower outlets incorporating brass bodies (various finishes) and NBR ‘O’-rings. Maximum operating temperature 85°C.
Range of shower outlets and shower kits. Shower outlets consisting of wall and ceiling mounted shower heads and hand shower. The inlets incorporate stainless steel flow regulators and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The shower kits can consist of shower hose, shower handset, riser rail and wall outlet elbow with bracket (depending on model). Shower handset inlet incorporates a stainless-steel strainer. Both the outlet of the wall elbow and inlet of shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
‘Concept’ & ‘Advance’ ranges of atmospheric steaming ovens. The products incorporate a retractable triple layered hose on a reel and a push-button operated shower handset. The inlet of the shower handset incorporates a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The water supply is controlled via a solenoid valve. The retractable hose has its own dedicated supply also controlled via a solenoid valve. The products are supplied with dual layer supply hoses (grey PVC outer layer/black PVC inner layer) with ¾” captive nut end connections, and chrome plated DZR brass ½” BSP (F) x ¾” BSP (M) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet. Maximum working pressure 4.0 bar. Cold supply only.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of flow switches with brass bodies and NBR/fibre gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Turbine flow sensors with a plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The DIEN-BT&DCV1/2” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of shower hoses available in a variety of external sheath materials and finishes (see models) with EPDM washers. Maximum operating temperature 65°C.
Range of stainless steel and brass double interlocked PEX lined flexible hose assemblies (various finishes - see model) incorporating EPDM washers. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of TPE lined flexible shower hoses incorporating a conical nut. Maximum operating temperature 60°C.
Range of plastic shower hoses (chrome effect finish) incorporating a PVC inner liner, with EPDM ‘O’-rings and/or washers. Models H3DN6-XXX101C and H3DV2-XXX101A incorporate stainless steel strainers. Maximum operating temperature 60°C.
Range of TPE and TPS lined flexible hose assemblies incorporating NBR ‘O’-rings and various end connections. Maximum operating temperature 60°C.
Range of multi-layered flexible hoses (TPE inner liner/PVC middle/PVC outer with polyester braiding in-between) and stainless-steel braided EPDM flexible hoses. The hoses are supplied with a variety of end connections incorporating brass barbed hose inserts or white plastic barbed hose inserts. The hoses may also incorporate a servicing valve (see model). The push fit connectors are to be used with copper pipe (Manufactured to EN1057), PB pipe (Manufactured to BS EN21003) & PE-x pipe (manufactured to BS EN7291-3). Products shown with a “P” suffix (eg. WFLX15P, FLX43P) are a prepacked variant of the original product eg. WFLX15, FLX43. Products shown with a “SB” suffix (eg. FLX15P-SB, WFLX28-SB) are a reduced box quantity of an existing product. Maximum working pressure and operating temperature: 12.0 bar @ 20°C and 6.0 bar @ 65°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel braided EPDM lined flexible hoses assemblies incorporating various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall mounted, bar type thermostatic shower mixer (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow with a dome operating member. The temperature is controlled independently via a thermostatic cartridge with a dome operating member. The outlet incorporates a single check valve cartridge assembly; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet connections incorporate an eccentric isolation valve and flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of electronic, thermostatic mixing valves which incorporate a solenoid valve on the inlet and various outlet configurations dependant on model. All models are supplied with a user interface that controls flow and temperature. The inlets of models 1.1503.678, 1.1503.682, 1.1503.690, 1.1503.698 & 1.1621.099 incorporate a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Model 1.1503.702 – Rada Sense W KIT T3 Washbasin is supplied with a wall mounted spout outlet. Model 1.1503.706 – Rada Sense S KIT T3 Shower is supplied with a fixed shower outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and discs and EPDM rubber seat. Maximum working pressure 16.0 bar. Cold water use only. Maximum operating temperature 85°C (from Sept 2021)
Single inlet, flow control valve with a brass body, incorporating a ‘detent’ (push to on push to off) headwork controlling the flow. The product is supplied with a trim sets in various finishes (see model) Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Monobloc assembly with a DZR brass body comprising of a stainless steel strainer, adjustable pressure reducing valve and two approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with two loose pressure gauges. For use with copper pipe (manufactured to EN1057). The product is also supplied with Maximum inlet supply pressure 6.0 bar. Maximum outlet pressure 0.8 bar to 6.0 bar. Maximum operating temperature 35°C.
Range of pressure reducing valves with DZR brass bodies. The capillary union and compression models are for use with copper pipe (manufactured to BSEN 1057). The inlets incorporate a stainless strainer. Reliance 315i Commercial Pressure Reducing Valves: Maximum supply pressure 21.0-25.0 bar - outlet adjustment range: 2.5 bar min. outlet pressure, 6.0 bar maximum outlet pressure. Maximum supply pressure 16.0-20.0 bar - outlet adjustment range: 2.0 bar min. outlet pressure, 6.0 bar maximum outlet pressure. Maximum supply pressure 11.0-15.0 bar - outlet adjustment range: 1.5 bar min. outlet pressure, 6.0 bar maximum outlet pressure. During January 2022 these products were for cold water use only. Between February 2022 and January 2027 the products are for use with water up to 65°C. Models added May 2025: Maximum supply pressure 25.0 Bar. Outlet adjustment range: 5.0 bar min, 10.0 bar maximum outlet pressure. Maximum operating temperature 65°C.
‘Easiset 320 series’ adjustable (in-line) pressure reducing valves with DZR brass bodies. Compression and pushfit models are for use with copper pipe (manufactured to BS EN 1057:2006+A1:2010). From March 2022 the pushfit models can also be used with PB pipe (manufactured to BS EN 7291-2:2010) and PEX pipe (manufactured to BS EN 7291-3:2010). Maximum inlet supply pressure: 16.0 bar all models with copper pipe. From March 2022: SBPRED320001 & SBPRED320005 models: 12.0 bar with PEX & PB pipe. SBPRED320050 & SBPRED320055 models: 6.0 bar with PEX & PB pipe. Maximum outlet pressure 1.5 bar to 5.5 bar. Maximum operating temperature: COLD WATER EASISET 320 SERIES: 45°C with copper pipe, and from March 2022: cold water use only with PEX & PB pipe. HOT WATER EASISET 320 SERIES: 80°C with copper pipe, and from March 2022: 80°C with PEX & PB pipe.
Range of adjustable, bronze in-line pressure reducing valves. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of adjustable, pilot operated, pressure reducing control valves with black plastic bodies, EPDM diaphragm, EPDM ‘O’-rings and NBR seals. The products are supplied with auxiliary stainless-steel tubing, lever operated spherical valves, integral stainless-steel strainer, pilot valve and a quarter turn ceramic disc valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 0 - 8.5 bar, 7.0 - 13.5 bar or 12.0 - 16.0 bar (see model). Maximum operating temperature 60°C.
Range of bronze bodied pre-set pressure relief valves (available between 0.2-16 bar on each model) incorporating a manually operated easing gear with brass seat and PTFE or EPDM washers. Maximum operating temperature 85°C.
Pressure relief valve pre-set at 6.0 bar, with a brass body and EPDM seat washer. Maximum operating temperature 115°C.
Range of pressure relief valves pre-set at 3.0 bar with brass bodies and a EPDM membrane. Valve incorporates a manually operated easing gear. Maximum operating temperature 85°C.
Solenoid valve with a plastic body, EPDM membrane and plastic or stainless steel strainer. From March 2023 the product may also be supplied with a Ø 28.61mm x ¾” BSP (M) plastic adaptor. From December 2023 the product may also be supplied with a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Non-metallic materials and components comply with BS6920 at 70°C
Range of screwdriver operated servicing valves incorporating brass bodies and chromium plated brass ball, nylon seats and EPDM seals. Maximum working pressure 7.0 bar. Maximum operating temperature 99°C.
Spherical valves incorporating bronze bodies with lever operating members, chromium plated brass ball and PTFE seat. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chromium plated brass balls and PTFE seats with lever, lockshield or T-type operating members. Maximum working pressures: 22mm – 28mm = 32.0 bar and 42mm – 54mm = 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brass body and ball (brushed chrome plated), and PTFE seals. Maximum working pressure 42.0 bar (¼”, 3/8”, ½”, ¾” models) Maximum working pressure 32.0 bar (1”, 1 ¼”, 1 ½”, 2” models) Maximum working pressure 28.0 bar (2 ½” model) Maximum working pressure 16.0 bar (3” & 4” models) Maximum operating temperature 85°C
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Combined spherical valve and strainer with a brushed chromium plated brass body and stainless-steel filter. The strainer incorporates single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of quarter turn PVC-U double union spherical valves with EPDM seals and PTFE Seats. Maximum working pressure 16.0 bar. Cold water use only
Range of ‘T’-handle, spherical vales with PVC-u bodies, EPDM ‘O’-rings and either a TPE seat seal (UCB01 model) or PTFE seat seal (all other models). For use with PVC-u pipe manufactured to ISO 1452 and DIN 8063. Maximum working pressure 10.0 bar. Cold water use only.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating brass bodies, brass wedge, PTFE and NBR washers and operated via a non-rising spindle headwork. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies and PTFE seals. The valves incorporate a non-rising stem and hand-wheel or lock shield operating members (see models). Maximum working pressure 20.0 bar. Maximum operating temperature 100ºC.
Range of gate valves with a DZR brass body and disc, and PTFE washers. The products are operated by a non-rising spindle headwork with a hand wheel operating member. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Tornado’ & ‘Ninjo’ ranges of freestanding and undercounter bedpan washers with flow controlled via a solenoid and discharged via type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 8.0 bar. Maximum operating temperature 60°C
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
'Iupital F10-01'. White coloured, injection moulded POM material. For use with water up to 85°C.
'IUPITAL F10-EW2 NATURAL'. Natural (appears white), injection moulded POM material. For use with water up to 85°C.
'Cage Overmould 214867'. Black coloured, injection moulded ABS component. For use with water up to 70°C.
'3M Silicon Carbide Type ‘F’, ‘F Plus`, ‘C’ & ‘G`. Dark grey coloured, sintered silicone carbide washers. For use with water up to 85°C.
‘PAM-MORTAR.D2'. Grey coloured (once mixed), factory applied Blast Furnace Slag Cement Mortar and admixture. Mix cement, sand, water & admixture in a mass ratio of 1:1.25:0.38:0.0008. Apply as per manufacturer’s technical data sheet dated 18/03/2021 (3rd revision) and cure for 48 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Jotapipe AC1003XT'. Factory applied, green coloured fusion bonded epoxy coating. Apply as per manufacturer's TDS dated 8 June 2021. Cure for 5 minutes@235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cementitious Coating 851 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '851 /031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nitocote CM210 '. Site applied, grey coloured, two-component cementitious coating comprising of Nitocote CM210 White (base coat) and Nitocote CM210 grey (top-coat). 'Nitocote CM210 White' (base coat) consists of Part A (white coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 4 hours@20°C. 'Nitocote CM210 grey' (top-coat) consists of Part A (grey coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 8 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NO MORE DAMP Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0420'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monomix WS'. Site applied, grey coloured cementitious waterproof mortar. Mix powder and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AXIL-76/T-MD'. White coloured (translucent), extruded silicone rubber hose. Shore hardness 80. Tested in-radius size between 0.75mm & 2.1mm. For use with water up to 85°C.
'PlumbSil & PlumbSil HT'. Colourless silicone greases. Apply as per manufacturer's instructions dated 18th Jan 2022. For use with water up to 65°C.
'S350 Silicone Fluid'. Colourless (transparent) silicone lubricant. Apply as per manufacturer's instructions for use 'LDAP-009', issue 1 dated May 2021. For use with water up to 85°C.
'Turbine Overmould 208399'. Black coloured, injection moulded, strontium ferrite filled nylon 6 component. For use with water up to 70°C.
'ForTii® WX11-FC BK00001, ForTii® PA Xgea21 BK28048 & PA Xgea21 BK28048'. 'ForTii® WX12-FC BK00001' was added to the approval in August 2023. Black coloured, injection moulded Polyamide materials. For use with water up to 85°C.
'Rilsan BZM 30 O TLD A'. Beige coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.
'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.
'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
`Grilamid TR 90 LS Natural & Grilamid TR 90 Natural`. Natural (colourless, transparent), injection moulded nylon materials. For use with water up to 85°C.
'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Omnix DW 4050 BK 001'. Black coloured, injection moulded PA material (manufactured in Oudenaarde, BE and Changshu, China). For use with water up to 85°C.
'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Genestar™ G1500D-L47WF BLACK'. Black coloured, injection moulded or extruded Polyamide 9T material. For use with water up to 85°C.
'Bearing p/n 238717'. Grey coloured, injection moulded PEEK component. For use with water up to 70°C.
`Veradel 3330GF`. Beige coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'MT PE-Xc/AL/PE-X Pipe' (formerly known as 'Hewing MT PE-Xc/AL/PE-X multi layer pipe'). Extruded, multi-layered pipes comprising of an off-white (translucent), PEX-Xc inner layer, aluminium middle layer and white coloured (opaque), PE-Xb outer layer. For use with water up to 85°C. Please note that the pipes will be marked with 'WRAS 2111538'. Pipes which do not have this marking are not covered by the scope of the approval.
'Instantor® Pex'. Translucent, white coloured, extruded, single-layered PE-Xb tubing. For use with water up to 85°C.
'CORREX®, Q-GUARD® & S-PATRON® PE-Xc Anode Frame (Clip)'. Cream coloured, injection moulded PE-Xc clip components. For use with water up to 85°C.
'CORREX®, Q-GUARD®, S-PATRON® & HYTONIC® PE-Xc Anode Gasket'. Cream coloured, injection moulded PE-Xc gaskets. For use with water up to 85°C.
'002DP48 Aiva Electrofusion Fittings'. Blue coloured, injection moulded HDPE electrofusion fittings. For use with water up to 23°C.
'Kott-Glide 2.0'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'EGPI HDPE BL-W Pipe'. Black coloured, (with blue coloured external stripe), extruded HDPE pipe. For use with water up to 85°C.
'C40'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
'K9'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Turbine Cage 241208'. Blue coloured, injection moulded PPO component. For use with water up to 70°C.
'Isoryl A 20 90 GF20 W NA'. Beige coloured, injection moulded PPO material. For use with water up to 85°C.
WOTLON MPPO 1000-GF2 BK006. WOTLON MPPO 1000-GF2 GY003. WOTLON MPPO 1000-GF2 NC001. WOTLON MPPO 1000-GF3 BK006 WOTLON MPPO 1000-GF3 GY003 WOTLON MPPO 1000-GF3 NC001 Natural (NC grades - appears beige in colour), black coloured (BK grades) and grey coloured (GY grades), injection moulded MPPO materials. For use with water up to 85°C.
'VIALLI PPR Pipes'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'SHK Aqua PP-R pipe'. Extruded, multi-layered PP-R pipe comprising of a white coloured inner, black coloured middle layer and green coloured outer layer. For use with water up to 85°C.
'Polygon PPR Pipe'. Green coloured (with red stripe), single layered, extruded PPR pipe. For use with water up to 85°C.
'Polygon PPR Fitting'. Green coloured, injection moulded PPR fitting. For use with water up to 85°C.
'Isoglas H30FVL (c) NA'. Translucent, off-white coloured, injection moulded, polypropylene material. For use with water up to 85°C.
`Polyfill PPH TS15040D Natural`. Natural (appears grey in colour), injection moulded polypropylene material. For use with water up to 85°C.
'Polyfill PPH GF8020 PB Natural'. Natural (appears off-white in colour), translucent, injection moulded polypropylene material. For use with water up to 85°C.
`Polyfill PPH T8020 1035 Grey & Polyfill PPHC T8040 1017 Grey'. Grey coloured, injection moulded polypropylene materials. Between February 2022 and September 2022, 'Polyfill PPHC T8040 1017 Grey' was for use with water up to 23°C. Between October 2022 and February 2027, 'Polyfill PPHC T8040 1017 Grey' is for use with water up to 85°C. 'Polyfill PPH T8020 1035 Grey' is for use with water up to 85°C.
`Acoflon 100`. White coloured, compression moulded PTFE washers. For use with water up to 85°C.
'AKORROS® B208A'. Brown coloured, extruded hard rubber Shore hardness 78. Tested in-radius size 1.11mm. For use with water up to 60°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
`EPDM7008`. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 2.7mm. For use with water up to 85°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
'70EP120P'. Black coloured, compression moulded, EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C.
'EPDM60BKFG, EPDM65BKFG, EPDM70BKFG, EPDM75BKFG & EPDM80BKFG'. Black coloured, compression moulded EPDM rubbers. Shore hardness between 60A & 80A. Tested in-radius size 1.0mm. For use with water up to 70°C.
0713.23/60 (shore hardness 60A). 0713.23/65 (shore hardness 65A). 0713.23/70 (shore hardness 70A). 0713.23/75 (shore hardness 75A). 0713.23/80 (shore hardness 80A). 0713.23/85 (shore hardness 85A). Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 85°C.
`SACHDEVA/EPDM-80`. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius 1.1mm. For use with water up to 23°C.
'E300'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'VI701/KTW'. Black coloured, injection moulded FKM 'O'-ring, shore hardness 70, tested in-radius 1.5mm. For use with water up to 85°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
‘NGP 60 T (Translucent – off-white), NGP 60 T/R (Transy Red), NGP 60 BK (Black), NGP 60 GY (Grey) & NGP 60 W (White)’. Extruded, platinum cured, silicone rubber tubing. Shore hardness 60. Tested in-radii sizes between 0.75mm & 1.5mm. For use with water up to 85°C
Bidet seat assembly with the flow controlled by a sensor actuated solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 1.75 bar. Maximum operating temperature 45°C.
A range of single-hole, single outlet (fixed (model 62816) or swivel (models 63407)) electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding 63407) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Incorporating a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator (SH-T9050N model) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a brushed chrome DZR brass body. For use with copper pipe EN1057. Fitting also incorporates a stainless steel strainer For maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, electrically heated catering water boilers. The boilers incorporate stainless steel storage tanks with stainless steel vent and overflow and silicon washers and gaskets, fed via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. The solenoid valve incorporates a plastic strainer at the inlet. Maximum working pressure 7.0 bar. Maximum operating temperature 98°C.
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A range of rotary cartridge headworks or ceramic cartridge headworks with plastic bodies and silicone seals. For insertion into specifically dimensioned bores. Models 38-7 and MD25FSF-2 are combined headwork and diverter cartridges, model M25SFS is a ceramic cartridge headwork. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of ceramic disc diverter cartridges with plastic bodies and silicon ‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of ceramic disc and non-rising spindle headworks headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and EPDM rubber ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of push to open, push to close headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. The products are available either as a version with a pop-up waste or one with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body. Incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic straightener. Maximum working pressure 3 bar. Maximum operating temperature 42°C
Range of single hole, single outlet (swivel) combination tap assemblies, brass bodies (various finishes) incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), incorporates a quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), With a quarter turn ceramic disc headwork with single lever operating members. Models M4306, M4306E & M4306F incorporate a non rising spindle headwork with dome type operating members. Model M4306G incorporate a non rising spindle headwork with cross top operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Model 805777 incorporate a non-rising spindle headwork with dome type operating members. Model 805783 incorporate a quarter turn ceramic disc headwork with single lever operating members. The fitting incorporates a manual diverter to the shower outlet The spout outlet incorporates a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headwork, single lever operating members and self- cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener & the products are supplied with metal backnuts. The product includes a shower hose and handset. Maximum working pressure 10.0 bar. Maximum working temperature 70°C.
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated). Incorporating quarter turn ceramic disc headworks, dome type operating members and self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Models TL30024CP and TR30024CP are supplied with a shower riser rail, shower hose and shower handset. Maximum working pressure 5.0bar. Maximum operating temperature 60°C.
Two-hole, single outlet swivel combination tap assembly in various finishes (see model) incorporating quarter turn ceramic disc headworks with a cross top operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies, brass bodies (various finishes) incorporating quarter turn ceramic disc headworks with various styles of operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided EPDM lined hose assemblies. The product is supplied with either a lever type pop up (HIRONDELLE models) or click type waste (ICON-X & CORVAIR models). Maximum working pressure 3.5 Bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of self closing shower column with brass body (chrome plated), incorporating a push button flow control and adjustable shower outlet. Maximum working pressure 8.0 bar. Cold water use only.
Range of wall mounted spout outlets with either stainless steel or brass bodies (various finishes - see model), incorporating a plastic aerator and EPDM ‘O’-rings. Maximum working temperature 60°C.
Range of spout outlets (chromium plated) brass bodies. Model 13 800 782 incorporates a plastic aerator. Maximum operating temperature 60°C
Range of wall mounted spout outlets with a chromium plated brass bodies and NBR ‘O’-rings. The outlets incorporate a plastic aerator. Maximum operating temperature 85°C.
A range of spout outlets with PVC lined stainless steel interlocked tube covered by silica gel. Model WD-PVC-09-10 is a double outlet. Maximum working temperature 65°C.
Filling loop assemblies comprising of a stainless steel braided, EPDM lined hose, double check valve assembly with isolation valve verified by test (suitable for backflow protection against fluid category 3) and either a straight or tee isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Filling link assembly with a nylon body and EPDM ‘O’-rings. The product incorporates a screwdriver operated shut off valve and two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). The product is also supplied with two screwdriver operated angled spherical valves and a mounting bracket. Maximum working pressure 10.0 bar. Cold water use only.
Filling loop assemblies comprising of a stainless steel braided, EPDM lined hose, double check valve assembly with isolation valve verified by test (suitable for backflow protection against fluid category 3) and either a straight or tee isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
>B< Range of copper push-fit fittings for use with copper tube manufactured to EN 10226-1. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings. For use with stainless steel tube. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of DZR brass couplings incorporating EPDM ‘O’-rings for use with Uponor Ecoflex Aqua and Uponor Ecoflex VIP Aqua PE-Xa pipe. For above and below ground use. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
>B< Press range of stainless-steel SUS316L fittings for use with 316L stainless steel tube manufactured to EN10312. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Center Brand range of brass and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of dual flush, WC outlet valves. CJ305 is operated via a push button assembly or with battery powered infra red sensor. CJ302 is controlled with a push button assembly for either full or reduced flush and both models incorporate an internal overflow. Cold water use only.
Range of plate heat exchanger with stainless steel bodies. Maximum working pressure10 bar. Maximum operating temperature 100°C.
‘POD’ range of indirect and direct heat interface units providing space heating and instantaneous hot water. The heat transfer is generated via plate heat exchangers. The domestic hot water (DHW) circuit incorporates an adjustable temperature mixing valve. The indirect models incorporate an expansion vessel (on the CW inlet of the DHW circuit) and a pressure relief valve set at 3.0 bar (on the space heating circuit). The indirect models only are supplied with a temporary filling loop, which comprises of a stainless steel braided EPDM lined flexible hose assembly and a lever operated spherical valve for connection to the primary circuit. The angled cold water inlet incorporates an isolation valve and a branch to connect to the filling loop, which includes a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3). Maximum working pressure for indirect units: Primary circuit: 16.0 bar. Space heating: 2.5 bar. Secondary circuit (DHW): 10.0 bar. Maximum working pressure for direct units: Primary circuit: 10.0 bar. Space heating: 10.0 bar. Secondary circuit (DHW): 10.0 bar. Maximum operating temperature for domestic hot water 65°C. Maximum operating temperature for central heating and primary circuit 85°C.
Electric instantaneous, vented mains water heater with plastic a housing and silicon rubber hose. Maximum operating temperature 98°C.
"Greenstar" range of indirect heat interface units and "Flow 8000" (added December 2024) range of direct heat interface units providing heating and instantaneous hot water. The heating system incorporates an expansion vessel. The products are sold with or without a prefix kit (see model), which comprises of a mounting bracket that includes spherical valves for all circuits. The "Greenstar" indirect models include a pressure relief valve (set at 3.0 bar) on the space (central) heating circuit. Greenstar models: Maximum working pressure district heating 10.0 bar. Maximum working pressure space heating 2.5 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary). Flow 8000 models (added December 2024): Maximum working pressure district and space heating 10.0 bar. Maximum working pressure secondary hot water 10.0 bar. Maximum operating temperature 60°C (secondary) and 90°C (primary).
Range of wall mounted, gas-fired, condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and a pressure relief valve set at 3.0 bar. The inlets to the domestic hot water and primary circuits each have a screwdriver operated angled spherical valve. Both include a ½” BSP (M) connection for a filling link. The Greenstar CDi models only are supplied with an integral charging link (CAB device) verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure of the primary circuit is 2.5 bar. Maximum working pressure of the secondary circuit is 10.0 bar. Maximum operating temperature of primary circuit is 82°C. Maximum operating temperature of secondary circuit is 60°C.
Range of commercial ice making machines with flow controlled via solenoid valve. Maximum working pressure 8 bar. Cold water use.
Water meter with a DZR brass body, stainless steel temperature sensors and EPDM ‘O’-rings. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of water meters with blue epoxy coated iron bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of water meter manifolds with gun metal bodies and ball valve with either a quarter turn stop valve or screw down stop valve. The products incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of concealed thermostatic mixing valves with DZR brass bodies incorporating a thermostatic cartridge controlling the temperature. The inlets incorporate asingle check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spout outlets with brass bodies (various finishes) incorporating an aerator. Product is supplied with either a lever type pop up (HIRONDELLE models) or click type waste (ICON-X & CORVAIR models). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Spout end flow control device (aerator with ‘switchable’ spray formation). Maximum operating temperature 65°C.
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of shower outlets incorporating brass bodies (various finishes) and NBR ‘O’-rings. Maximum operating temperature 85°C.
Shower outlet incorporating brass body (gold effect finish), incorporating a flow regulator and EPDM O-rings. Maximum operating temperature 60ºC.
Shower head with a brass body (various finishes), incorporating EPDM O- rings and a stainless-steel strainer at the inlet. Maximum operating temperature 60.0°C
Ranges of overhead shower outlets with brass bodies, chrome plated plastic shower handsets, shower sets and shower kits. The shower sets comprise of a chrome plated plastic shower handset and shower hose. The shower kits comprise of a chrome plated plastic shower handset, brass wall elbow and either stainless steel interlocked, or PVC coated, shower hoses. The inlets of the shower handsets incorporate a plastic flow regulator at the inlet. Shower kits with ½” (M) inlets are also supplied with a brass wall elbow which incorporate a plastic flow regulator and an approved single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum operating temperature 60°C.
Range of shower outlets (celing or wall mounted arms - see model) with chrome plated brass bodies and silicone nozzles. The products incorporate a swivel joint connection to the shower head which incorporates a combined NBR washer and stainless steel strainer. All models, except for the 15199 model, include a plastic flow regulator on the inlet to the shower head. Maximum operating temperature 60°C.
Range of overhead shower outlets with brass bodies (various finishes, see model), incorporating stainless steel strainer and flow regulator on the inlets. Maximum operating temperature 60°C.
Range of shower handsets with plastic bodies incorporating an integral filters. The inlet incorporates a combined washer and a strainer, plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C
Range of in-line `Y` patterned strainers with bronze bodies and stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C. Closed circuit up to 110°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of wall mounted hose union taps (brass body or DZR brass body - see model) incorporating a non-rising spindle headwork with a ‘T’-type operating member. The 1BCB001 & 1BCB701 models incorporate two approved single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 14.0 Bar. Maximum operating temperature 85°C.
Deck mounted laboratory tap, grey powder coated brass body, with three outlets: two are fixed, one is a swivel spout. Each outlet has its own individual quarter turn ceramic disc headwork controlling the flow with a dome type operating member, and a hose union attachment. The product is supplied with a brass backnut. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
A range of wall mounted self-closing pillar taps or shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic flow straightener. During January and February 2022, the products are supplied with metal back nuts. From March 2022, the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
A range of wall mounted self-closing pillar taps or shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. T Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of self-closing taps with chromium plated brass bodies, incorporating a non-concussive headwork with or without operating members (see model). The GR 120 + GR 138 + GR 100 model represents three parts which must be installed together to create one complete product. It comprises of a gooseneck spout (chromium plated brass) (GR 120), a single self-closing side valve (brass) incorporating a stainless steel strainer on the inlet (GR 138) and a loose inlet tee piece (chromium plated brass) (GR 100). The inlets of the GR 102M model and the GR 100 tee piece incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. All models, except for the GR 102M model, are supplied with metal back nuts. All spouts incorporate a plastic flow straightener. The GR102M model incorporates a manual temperature control operated by a single lever on the side of the body, on all other models this is achieved via an adjustment plug in the base of the tee piece. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of PET (Polyethylene terephthalate) braided flexible hoses incorporating PEX liner and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. (10.0 bar for models added September 2025). Maximum operating temperature 70°C.
Range of stainless steel braided HDPE lined flexible hose assemblies incorporating EPDM ‘O’-rings and/or washers depending on end connection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of stainless steel or nylon braided PEX lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. SCFA models incorporate a spherical valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided, PEX lined flexible hose assemblies with a variety of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of EPDM or PVC lined flexible hose assemblies with either nylon braided, or chrome plated interlocking outer layer (see models). Maximum operating temperature 85°C.
Range of 2, 3 or 4 way manifolds with a brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, exposed, manual blending valve (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member controlling both flow and temperature. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
A range of wall mounted thermostatic blending valves with brass bodies (various finishes). The temperature is controlled via a thermostatic cartridge and dome operating member and flow is controlled via a quarter turn ceramic headwork. Product can come with one, two or three push type cartridges that divert the flow to various outlets (see model) The inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of T type thermostatic blending valves with (nickel plated) DZR brass bodies. The inlets incorporate a stainless-steel strainer and single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2) Models HEAT160030 & HEAT160035 also incorporate a servicing valve at the inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic blending valves with brass bodies (chrome plated), incorporating two way diverter valves controlling the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model SL-T50004BW has a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 6.0 bar. Maximum operating temperature is 85°C.
Wall mounted exposed thermostatic blending valve (chromium plated brass). Incorporating a thermostatic cartridge which controls both flow and temperature independently with a single lever (flow) and cross top or single lever (temperature) operating members. The flow control incorporates a manual override button. The inlets incorporate stainless steel strainers and an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members, model (34458892) is supplied with cross-top operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet to the overhead shower incorporates a stainless steel strainers and flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic blending valves with brass bodies (various finishes), incorporating a quarter ceramic disc headwork controlling the flow with dome type operating member. Temperature is controlled via a thermostatic cartridge with dome type operating member incorporating a manual override button and a push button manual diverter to shower outlet. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless steel or ductile iron discs (nickel plated). The products are supplied with either bare shaft or with lever or gear operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Manual diverter valve controlling the flow to a hand shower or overhead shower, housed within a brass body (various finishes). Incorporating a stainless-steel strainer and approved check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 70°C.
Wall mounted, brass bodied shower control valve incorporating a quarter turn ceramic disc headwork with a chrome plated trim set and operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of non-return valves housed within a blue or black epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return valves housed within black epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return valves housed within a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line manually adjustable pressure reducing valves with blue epoxy coated cast iron bodies, stainless steel cartridges, EPDM diaphragm and seals. Adjustable outlet pressures in the range of: D15S-50A - DS15S-100A = 1.5 to 7.5 bar. D15S-150A - DS15S-200A = 1.5 to 8.0 bar. Models added April 2023: D15SN-50A - DS15SN-100A = 0.5 to 2.0 bar. Maximum supply pressure 16.0 bar. D15S-150A and D15S-200A models: Cold water use only. All other models have non-metallic material suitable for up to 60°C.
Range of pressure reducing valves with DZR brass bodies, integral stainless steel strainer, and EPDM ‘O’-rings and membrane. The oulet pressure is adjustable between 1.5 bar and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 70°C.
Range of in-line manually adjustable pressure reducing valves with blue epoxy coated cast iron bodies, EPDM rubber diaphragm and seals. Maximum supply pressure: A suffix model (added April 2023): 16.0 bar. B suffix models: 25.0 bar. Adjustable outlet pressure 3.0 to 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pressure reducing valves with DZR brass bodies adjustable between 1.0 and 6.0 bar. The valves incorporate a stainless steel strainer. Maximum supply pressure 25.0 bar or 16.0 bar (see model). Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar or 1.0 and 12.0 bar (see model). Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pre-set angled pressure relief valves for use on primary closed circuits, incorporating DZR brass bodies, EPDM diaphram and EPDM or NBR ‘O’-ring. For maximum working pressure please refer to model. Maximum operating temperature 99°C.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of inline and angled screwdriver or lever handle operated spherical valves with (chromium plated) brass bodies, chromium plated brass ball, NBR ‘O’-rings. For use with copper pipe manufactured to EN 1057 Maximum working pressure 16.0 bar at 30°C and 5 bar at 99°C Maximum working pressure 6.0 bar. Maximum operating temperature 90°C (model TX480 only)
Spherical valve incorporating bronze body, stainless steel ball and PTFE seats and seals. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating nickel plated brass bodies, chrome plated brass balls & Tee type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
ISIS range of single lever and T type operated spherical valves with DZR brass body and ball (chrome plated), and PTFE seals. Maximum working pressure 40.0 bar (¼”, 3/8”, ½”, ¾”, 1”, 1 ¼”, 1 ½”, & 2” models) Maximum working pressure 10.0 bar (2 ½”, 3” & 4” models) Maximum operating temperature 100°C
Range of spherical valves with brass bodies (brushed chrome plated), (red coloured) lever operating members and chrome plated brass ball. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass bodies, brass ball, PTFE washer and seats, incorporating a butterfly handle operating member (R254 models) or single lever operating member (R254DL models). Maximum working pressure 42.0 bar (¼ - ½” models). Maximum working pressure 35.0 bar (¾” - 2” models). Maximum operating temperature 99°C.
Range of lock shield or handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
Range of UV disinfection units incorporating 316L stainless steel bodies and quartz sleeves. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
'FC941'. Black coloured, injection moulded, carbon graphite bearing. For use with water up to 85°C.
'CS15 & LF1'. Dark grey coloured, pressed and sintered silicon carbide ceramic materials. For use with water up to 85°C.
'Rapal Light C795' disc. White coloured, compression moulded, ring shaped ceramic gliding disc. For use with water up to 85°C.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add PLUS 2.5'. Grey coloured, site-applied waterproofing admixture. Admixture is to be added to cement mix in a dosing ratio of 2.5 kg per m3 of concrete. Cure for 5°C for 48 hours. For use with water up to 23°C. This material is only approved for the dosing and curing conditions that appear on the approval. If the dosing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LATTYflon 4789'. Yellow coloured, braided fibre/PTFE gland packing. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'LATTYgraf EFA'. Grey coloured, graphite sheet material manufactured by calendaring. For use with water up to 85°C.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'SANIBIW WB Hose’. Single layered, uncoloured & translucent (natural), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size of 2.0mm. For use with water up to 85°C.
'Seplite LSF 983'. White coloured ion exchange resin. For use with water up to 85°C.
'IKV Tribosil MHL 40'. Clear silicone liquid lubricant. Apply as per manufacturer's technical data sheet. No cure required. For use with water up to 85°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'Akoalit PB 4268 White & Akoalit PB 4267 Grey'. White or grey coloured, extruded polybutylene material. For use with water up to 85°C.
'Akoalit PB R 539'. Natural (which appears white coloured), compression moulded polybutylene material. For use with water up to 85°C.
'PB DKG 300'. Natural, (appears beige coloured), compression moulded polybutylene material. For use with water up to 85°C.
`Pocan B1501 000000`. Natural (appears white coloured), injection moulded PBT material. For use with water up to 85°C.
'Ultrason E 6020 P Natural'. 'Ultrason E2010 G6 Uncoloured’ was added to the approval in September 2022. Natural (appears yellow/brown), injection moulded PESU materials. For use with water up to 85°C.
‘Ultrason® E 2010 G4 Uncoloured’. Beige coloured, injection moulded polyethersulphone material. For use with water up to 85°C.
'Ultrason® E 2010 natur'. Light yellow coloured, injection moulded PES materials manufactured in Germany and South Korea. For use with water up to 85°C.
'Protecta-line Pipes PE80 & PE100 Pipes'. Extruded, multi-layered pipes comprising of a black coloured PE80 or PE100 inner layer, aluminium middle layer and blue coloured PE80 or PE100 outer layer. The pipes have a black external stripe. For use with water up to 23°C.
'Vialli PEXa Pipe'. White coloured (translucent), extruded PEXa pipe. For use with water up to 85°C.
‘PE-Xc PENTA Pipe’ (formerly known as 'Hewing PE-Xc PENTA Pipe (off-white or beige)'. The extruded pipes have either an off-white (natural) OR a beige coloured, polyethylene inner and outer layer. The middle layer is EVOH (oxygen barrier). Both for use with water up to 85°C.
‘Ultrason® P3010 MR White 20264’. White coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
‘Ultrason® P3010 MR Black 10101’. Black coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
‘Ultrason® P3010 Natural’. Light brown coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
'LSPPR-GY001'. Grey coloured (with red or blue external stripe), extruded polypropylene pipe. For use with water up to 85°C.
'GREAN PIPE PPR Pipe'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'GREAN PIPE PPR Fitting'. Green coloured, injection moulded PPR fitting. For use with water up to 85°C.
'LSPPR-GY001'. Grey coloured, injection moulded polypropylene fitting. For use with water up to 85°C.
'Temprite 88031 PVC-C Fitting'. Light grey coloured, injection moulded PVC-C fitting. For use with water up to 60°C.
`Chemonit 181`. Black coloured, hard rubber material manufactured by roller head extrusion and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'9711/2 Black'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radii sizes between 0.88mm & 2.85mm. Between October 2021 and July 2022, the components were for use with water up to 23°C. Between August 2022 and October 2026, the components are for use with water up to 85°C.
'EP2/2/4 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 45 IRHD. Tested in-radius size 0.9mm. For use with water up to 85°C.
'EWDRI 50, EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 0.69mm. 'EWDRI 50' is for use with water up to 70°C. 'EWDRI 55, EWDRI 60, EWDRI 65, EWDRI 70 & EWDRI 80' are for use with water up to 60°C.
'E51-70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EUW-80'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'SIL8701 Red 'O'-rings'. Red coloured, injection moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
'LP60ANAT 368'. Natural (appears off-white), compression moulded silicone rubber material. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
‘Silopren LSR 2030, 2040, 2050, 2060, 2070 & 2080’. Natural (appears clear), compression moulded silicone rubbers with a shore hardness between 30 and 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'Adey MCXS Clear'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet 'issue 1' dated 03/03/2022. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikasil DW Trans'. Site applied silicone sealants available in transparent (CO0 transparent), grey (RA1 7004) or black (CO4 Schwarz). Apply as per manufacturer's instructions Product Data Sheet 'April 2022, Version 04.01'. Cure for 24 hours@7°C. The transparent (CO0 transparent) and grey (RA1 7004) sealants are for use with water up to 85°C. The black (CO4 Schwarz) sealant is for use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Loctite® AA 326 with Loctite® SF 7649™ Activator'. Loctite® AA 326 is an amber coloured, liquid anaerobic adhesive and Loctite® SF 7649™ is a green coloured, liquid activator. Apply as per manufacturer's Technical Data Sheet dated December 2013. Cure 7 days@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted electric showers (various finishes). The GSD/BETTER models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/DSK/ENTRY models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). Incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of wall mounted electric showers (various finishes). The GSD models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/ models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (various finishes), incorporating an electronic cartridge controlling the flow which is activated via an infrared sensor (either battery or mains powered). Models 31 171 xxx & 31 173 xxx incorporates a manually operated temperature control. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass or nickel plated DZR brass body. Compression models are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of low flow rate tap regulators and spray changers, comprising of an EPDM ‘O’-ring, with a stainless-steel strainer housed within a brass body with chrome plated brass trim piece. Maximum working pressure Open outlet use. Maximum operating temperature 85.0°C
Range of ceramic cartridge headworks with plastic bodies and silicone seals for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C. (Model: 35D-10DP) Maximum operating temperature 65°C.
Deck mounted side valve incorporating a quarter turn ceramic disc (various finishes) with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with brass or plastic bodies (see model) and EPDM ‘O’-rings. The GR-FX-02S, 03SC, 10T, 11T, X02S, X02T & X05 models incorporate a stainless-steel strainer. For insertion into specifically dimensioned bores. Maximum operating temperature 75°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model 3034-CR has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and models 31 088 000 & 31 183 000 are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator and Model 16 515 xxx is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model A05406 has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes), ceramic cartridge headwork with a single lever operating member and waterfall spout outlet. The waterfall spout outlets of models A05421, A05422 & A05418 incorporate a stainless-steel mesh. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with either a single lever, cross top or dome type operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type with or without a stainless-steel mesh (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a push on/off headwork with rotary temperature control using dome type lever operating member. Both inlets incorporate stainless steel strainers an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Some models are supplied with lever type pop up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.
Range of floor mounted, single outlet (fixed) combination tap assembly with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a single lever operating member. The shower outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with a shower hose and shower handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The outlet from the self-cancelling diverter incorporates an approved check valve cartridge (except model 31 930 xx0), Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly brass body (various finishes, see models) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. The 32 082 xxx model is supplied with a click type waste, the 32 084 xxx & 71 130 xxx models have a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (TR1027 and TR1005 models) or a plastic aerator (all other models). The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Deck mounted two-hole, single outlet, fixed combination tap assembly (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of concealed wall mounted two hole, single outlet, (fixed) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Deck mounted two-hole, single outlet, fixed combination tap assembly (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts and an optional stainless steel mesh washer for installation in the spout outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two hole, single outlet (fixed) combination tap assemblies. The product comprises of a trim set (various finishes - see model) and a concealed brass body. The trim set includes a ceramic cartridge headwork with a single lever operating member, headwork collar and a brass spout for installation into the concealed body. The spout outlet incorporates a plastic aerator, as well as a plastic strainer and plastic flow regulator on its inlet. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
A range of wall mounted two-hole single outlet fixed combination tap assemblies with brass bodies and various finishes (see models). Incorporating a combined shut-off and manual diverter cartridge which diverts between the bath or shower outlet with various operating members (see models). The temperature is controlled independently via a thermostatic cartridge with a manual override button with dome type or single lever type operating members (See models). Both inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar, Maximum working temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headwork, single lever operating members and self- cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener & the products are supplied with metal backnuts. The product includes a shower hose and handset. Maximum working pressure 10.0 bar. Maximum working temperature 70°C.
Wall mounted two-hole, single outlet (fixed) combination tap assemblies, brass bodies with various finishes (see model) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork, single lever operating member and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assemblies (various finishes, see models). Incorporating ceramic cartridge headworks and single operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of two hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever, cross top or wheel operating members. The spout outlet incorporates a plastic aerator and the product is supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies consisting of a concealed brass body with a spout and trim kit (various finishes - see model), incorporating quarter turn ceramic disc headworks with various operating members (see models). The spout outlet incorporates plastic aerator. Maximum working pressure 5.0 bar. Maximum working temperature 65°C.
Deck mounted, three hole, single outlet (fixed) combination tap assembly (brass body, various finish - see models) incorporating quarter turn ceramic disc headworks with single lever operating members. The product is supplied with a stainless steel braided thermoplastic silicone rubber lined flexible hose assemblies for installation between the headworks and the spout, a pop-up waste and metal backnuts. The spout outlet incorporates a combined plastic flow regulator and plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C
Self closing shower column with brass body (chrome plated), incorporating a push button flow control and adjustable shower outlet. Maximum working pressure 8.0 bar. Cold water use only.
Range of self closing shower column with brass body (chrome plated), incorporating a push button flow control and adjustable shower outlet. Maximum working pressure 8.0 bar. Cold water use only.
Range of combined bath fillers and overflow waste assemblies (plated brass covers and plastic hoses) with pop-up wastes. Maximum operating temperature 65ºC. Open outlet use only.
Wall mounted spout outlet (brass body, various finishes - see model) incorporating a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spout outlets with brass bodies (chrome or gold effect finish), incorporating an aerator in the spout outlet. Open outlet use, maximum operating temperature 60°C.
Range of water filter heads and housings (sumps). The HIS/IN4 models have a chrome plated stainless steel filter head and housing, all other models have a plastic filter head and housing. Ecofast/IN3/QT models incorporate an integral quick turn shut off valve within the filter head to allow the filter housing to be removed. All models are for use with John Guest LLDPE pipe. Maximum working pressure 6.0 bar. Cold water use only.
A range of blue epoxy coated steel reverse rinsing fine filters with a stainless-steel sieve and an EDPM O-ring. Supplied with two pressure gauges and metal ball valve on the drain. Maximum working pressure 16 bar. Maximum operating temperature 40°C.
Range of medical sterilised water filter cartridges with plastic bodies and EPDM ‘O’-Rings. Models MTFW-SLSS / MTFD-SLSS incorporate a check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum Working Temperature: 50°C.
A range of water filter cartridges with polypropylene bodies. Maximum working pressure 8.6 bar. Cold water use only.
Tigris K5 (PPSU - plastic body) and M5 (DZR brass body) ranges of press-fit (U, H, TH crimp profiles) fittings with stainless steel crimp sleeves and EPDM ‘O’-rings, for use with Tigris K1 multi-layer PEX-c/AL/PE-HD pipe. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of brass, chrome plated brass or DZR brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘AF’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). The AF14 and AF15 tap connector models incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Range of tee fittings incorporating DZR brass bodies (chrome plated) and approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) for use with copper pipe to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Tectite Sprint’ range of pushfit fittings with copper or DZR brass bodies. 10mm, 15mm, 22mm & 28mm pushfit fittings are for use with copper pipe (manufactured to BS EN 1057) and polybutylene barrier pipe and cross linked PEX barrier pipe (manufactured to BS 7291). 35mm, 42mm & 54mm pushfit fittings are for use with copper pipe (manufactured to BS EN 1057) only. When used with PB & PEX pipes operating parameter are: 12.0 bar@cold water. 3.0 bar@92°C. When used with copper pipes operating parameter are: 20.0 bar@cold water. 10.0 bar@100°C.
Range of M type press fittings with TP2 copper bodies and EPDM ‘O’-rings, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Instantor’ range of press-fit fittings incorporating DZR brass or Gunmetal bodies and EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum working temperature 95˚C.
Dual flush, WC outlet valve controlled with a push button assembly for either full or reduced flush and both models incorporate an internal overflow. Cold water use only.
Range of stainless-steel plate heat exchangers. Maximum operating pressures - primary circuit: 3.0 bar, secondary circuit (DHW): 10.0.bar. Maximum working temperature 80°C.
Under counter electric instantaneous water heater with a stainless steel tank. The flow is controlled via a solenoid valve. The product is supplied with a 3 way isolation valve (15mm compression x 15mm compression x ¾” BSP (M)), as well as a filter head and filter cartridge for installation prior to the under counter unit. LLDPE tubing and pushfit connections are provided for connecting between these items. The filter head inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet to the under counter unit incorporates a combined silicone washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.5 bar. Maximum operating temperature 98˚C. Cold water supply only.
Range of electric combination boilers providing heating and instantaneous hot water. The heating system incorporates an expansion vessel and pressure relief valve (set at 3.0 bar). The DHW inlet and outlet incorporate spherical servicing valves. Fittited with a CAB device keyless filling link, verifired by test, suitable for category 3 backlfow protection. Maximum working pressure on central heating circuit 2.5 bar & Domestic Hot Water 10bar. Maximum operating temperature 80°C
Hydraulic block assembly comprising of a flow regulator, central heating pump assembly and a stainless-steel plate heat exchanger. Maximum working pressures: DHW circuit: 10.0 Bar Central heating circuit: 2.5 Bar Maximum operating temperature: DHW Circuit: 65.0°C Central heating circuit: 90.0°C
Range of pressure transmitters with stainless steel bodies. Maximum working pressure 10.0 to 200.0 bar (please refer to model). Maximum operating temperature 100°C.
Range of aerators with plastic bodies and chrome plated brass housing. Open outlet use only. Maximum operating temperature 65°C
Range of wall mounted handwash basins with copper piping and PTFE orings. Maximum working pressure 8.0bar. Maximum operating temperature 85°C
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of self-priming jet pumps with stainless steel bodies. Maximum working pressure 6.0 bar. Maximum operating temperature 45°C
Range of booster sets with a stainless steel manifold system connecting 2 or 3 wholesome water pumps (For BOSS 2HELIX & BOSS 3HELIX models only). The set also includes spherical valves, and a non-return valve Maximum working pressure: 10.0 Bar Maximum operating temperature: 40°C
Range of vertical multistage booster pumps, with stainless steel bodies and impellors. Maximum working pressure is either 16.0 or 25.0 bar depending on specific model. Maximum operating temperature 85°C.
‘Matrix’ range of horizontal multistage stage centrifugal booster pumps with stainless steel bodies, stainless steel impellers, EPDM ‘O’-rings and a carbon/ceramic/EPDM mechanical shaft seal. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single and twin line shower booster pumps with plastic bodies, plastic impellors, stainless steel motor, NBR ‘O’-rings and EPDM seals. Each suction port incorporates a combined EPDM washer and stainless steel strainer. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of shower arms, ceiling arms, water intakes and wall mounted outlet brackets (all models excluding INOX are chrome plated brass, INOX models are stainless steel). Maximum operating temperature 60.0°C
Overhead shower outlet with a chrome plated plastic body. The inlet incorporates a stainless-steel strainer. Maximum operating temperature 65°C.
Range of shower outlets: swivel ball joint overhead shower heads with brass bodies (chrome plated) and shower handsets with plastic bodies (chrome plated). The overhead showers incorporate a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Overhead shower heads with brass bodies (chrome plated) incorporating a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Range of shower outlets with plastic bodies (various finishes) incorporating a stainless-steel strainer and a flow regulator. Maximum operating temperature 60°C.
Range of chrome plated plastic bodied shower heads. Maximum operating temperature 60 °C.
Range of wall or ceiling mounted shower outlets with chromium plated plastic bodies and EPDM O-rings. Maximum operating temperature 60°C.
Range of ceiling tubes for shower heads with brass bodies (various finishes) and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of overhead shower outlets with stainless steel bodies that incorporates a flow regulator and stainless-steel strainer. Maximum operating temperature 60°C.
Range of shower handsets with plastic bodies (various finishes) incorporating stainless steel strainers on the inlets and flow regulators (on models 26 827 XXX and 26 829 XXX). Maximum operating temperature 60°C.
Range of overhead shower outlets with brass bodies (various finishes), incorporating a plastic strainer at the inlet. Maximum operating temperature 60°C.
Range of shower handsets with either stainless steel or brass bodies (various finishes). Product is supplied with a metal sheathed flexible hose. Maximum operating temperature 60°C.
Range of shower outlets with plastic bodies (various finishes), incorporating EPDM o rings and stainless-steel strainers on the inlets. Models (24130xxx & 24132xxx) are overhead showers and model (24139xx0) is a wall mounted shower outlet. Model 24132xxx incorporates a flow restrictor on the inlet.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower heads with or without wall connectors (see models) with plastic bodies (various finishes). The shower heads incorporate a stainless-steel strainer and plastic flow regulator on the inlet. Model added September 2023: Wall mounted, brass shower arm (various finishes - see model). Non-metallic materials and components comply with BS6920 at 60°C Models added September 2023 and January 2024: Non-metallic materials and components comply with BS6920 at 65°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with brass and plastic bodies, various finishes (see models). The inlets incorporate stainless-steel filters and plastic flow regulators. Maximum operating temperature 60°C. Open outlet use only.
Range of flow sensors with brass or plastic bodies (see model). Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of flow switches with plastic bodies, models (SSCG-1-S70 & SSCG-1-S101) , incorporate EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The JMYG-064 1/2” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of wall mounted hose union taps with brass bodies, incorporating a rising spindle headwork with a ‘T’ type operating member. BC01L & BC01LA models are lockshield type. The BC01A & BC01LA models incorporate an approved check valve cartridge on the inlet and outlet however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Catering tap with chromium plated brass body and bonnet, incorporating silicone seat cups with single lever operating member. Maximum working pressure 0.1 bar. Maximum operating temperature 98°C.
Range of shower hoses available in a variety of external sheath materials and finishes (see models) with EPDM washers. Maximum operating temperature 65°C.
Range of “MEGAAIR” bubble top indirect and direct single coil unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 10.0 bar@90˚C. A safety kit (manifold) consisting of a single check valve assembly, verified by test (suitable for backflow prevention against fluid category 2), strainer, an expansion relief valve set at 8.0 bar and a pressure reducing valve set at 3.0 bar and a tundish is also provided. Alternative inlet control group and temperature and pressure relief valve added January 2023. Maximum working pressure: Secondary circuit: 7.5 bar. Primary circuit: 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, manually operated, concealed blending valves with chromium plated brass bodies and either brass or stainless-steel trim (see model). The product incorporates a ceramic cartridge headwork with a single lever operating member. The product is supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ¾” captive nut end connection for installation on the outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted thermostatic blending valves (chromium plated brass), with quarter turn ceramic disc headworks with cross top operating members and a manual diverter with a single lever operating member diverting the flow to two outlets. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Supplied with a shower hose, shower handset, riser rail and overhead shower outlet which incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, manual blending bath shower mixers (brass bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter (to divert the flow between a shower outlet or bath spout outlet - not supplied). The products comprise of a basic set, (concealed body), which includes the ceramic cartridge and a finish set that includes the self-cancelling diverter, headwork collar, operating member and trim set. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Wall mounted, manual blending valve (brass body, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of concealed thermostatic mixing valves, incorporating quarter turn ceramic disc headworks, with dome type operating members, controlling the flow to multiple shower outlets. The temperature is controlled independently via a thermostatic cartridge with dome type operating member. The inlets incorporates stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model 65036+54073 supplied with a shower handset and hose. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Wall mounted, thermostatic shower valve (chromium plated brass). Flow is controlled by a quarter turn ceramic disc headwork with single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a cross-top operating member that incorporates a manual override button. The product is supplied with a shower rail and overhead shower. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted, thermostatic, shower mixers incorporating brass bodies (various finishes) 2-way ceramic disc diverter headwork to control the flow between two shower outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge using various operating members (see model) that also incorporates a manual override button. The inlets incorporate a combined EPDM washer and stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet of the overhead shower incorporates a combined EPDM washer and stainless-steel strainer. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted exposed thermostatic mixing valves with brass bodies (various finishes). Incorporating a ceramic disc headwork with single lever operating member controlling the flow of the outlet on the bottom of the valve and three push button cartridges, two control the flow to outlets at the rear of the valve, and one to the outlet on the bottom of the valve all with cube type operating members. The temperature is controlled independently via thermostatic cartridge with a dome type operating member with a manual override button. The inlets and outlet at the bottom of the valve incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Range of wall mounted exposed thermostatic mixing valves with brass bodies (various finishes). Incorporating a ceramic disc headwork with a single lever operating member controlling the flow to a hose outlet and then two push button cartridges, one controls the flow to an outlet at the rear of the valve and the other to the outlet on the bottom of the valve with cube type operating members. The temperature is controlled independently via thermostatic cartridge with a dome type operating member with a manual override button. The inlets and outlet at the bottom of the valve incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Wall mounted, exposed thermostatic shower valve (brass body, various finishes) incorporating a non-rising spindle headwork controlling the flow with a dome operating member. The temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. Both inlets incorporate stainless steel strainers and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, bar type thermostatic shower mixers (various finishes). Incorporating a quarter turn ceramic disc headwork controlling the flow to the outlet with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member with a manual override button. Both inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
Wall mounted, thermostatic shower valve with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with a single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with shower hose, handset, and riser rail. Maximum working pressure 10.0 Bar Maximum operating temperature 70°C.
Range of wall mounted thermostatic shower valves (chrome plated brass bodies) incorporating a two-way diverter valve controlling the flow between shower outlets with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member with manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Three-way diverter valve with a stainless-steel body and stainless-steel ball. Maximum working pressure 9.8 bar Maximum operating temperature 80°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of adjustable in-line pressure reducing valves, the inlets incorporate a stainless-steel strainer. Models TS-504-505 & TS-506-508 have brushed chrome, DZR brass bodies. Model TS-501-503 has a DZR brass body. Maximum supply pressure 8.0 bar. Maximum outlet pressure 1.0 bar to 6.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with nickel plated DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 0.5 and 6.0 bar. The products are supplied with an optional pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies adjustable between 1.0 and 6.0 bar. The valves incorporate a stainless steel strainer. Maximum supply pressure 25.0 bar or 16.0 bar (see model). Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of in line adjustable pressure reducing valves with (brushed chrome plated) DZR brass bodies for use with copper pipe manufactured to EN1057. The valves incorporate stainless steel strainers and are supplied with pressure gauges. Maximum supply pressure 16.0 bar. Outlet pressures are adjustable between 1.0 and 6.0 bar. Maximum operating temperature 85°C
Range of normally closed solenoid valves with brass bodies, stainless steel spring, EPDM seal and diaphragm. Maximum working pressure 9.80665 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves incorporating brass bodies (nickel plated), brass balls (chrome plated) and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chrome plated brass ball and PTFE seats with tee-handles or lever type or extension stem type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of spherical valves with brushed chrome brass bodies, chrome plated brass ball incorporating a PTFE seat and NBR O rings. For use with EN1057 copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10.60982.015.CP12-8510) Maximum working pressure 25.0 bar (model 10.62022.015.CP12-8510) Maximum working pressure 40.0 bar (models 10.61062.015.CP12-8510 & 10.61062.022.CP12-8510) Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of angle valves (chromium plated brass bodies) with EPDM O-rings and washers. The products incorporate non-rising spindle headworks with dome type operating members. Maximum working pressure 10 bar. Maximum working temperature 80°C.
Range of in line double regulating valves with DZR brass bodies, EPDM ‘O’-rings and PTFE valve seals. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function with a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial front loading washing machines with flow controlled by solenoid valve and discharged via a type AD air gap arrangement (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with a single check valve assembly (suitable for backflow protection against Fluid Category 2) and PEX lined rubber inlet connections hoses. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'Delrin® FG511DP NC010'. White coloured, injection moulded semi-opaque acetal material. For use with water up to 85°C.
'M9000'. Grey coloured, injection moulded POM material. For use with water up to 85°C.
'ABS-NBK White & ABS-NBK 1C Grey'. White or grey coloured, injection moulded ABS materials. For use with water up to 85°C.
‘ABS 757K (Grey) & ABS 757K (White)’. Injection moulded Acrylonitrile Butadeine Styrene Copolymer (ABS) materials. For use with water up to 85°C.
'AD-94 Sealing Ring'. White coloured, compression moulded ceramic sealing ring. For use with water up to 85°C.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'issue reference SPI 20170215' dated 21st January 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POWTON E5000P-WT (grey)'. Factory applied, grey coloured, epoxy powder coating. Apply as per manufacturer's TDS dated January 21st 2015. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Blue coloured, factory applied, Fusion Bonded Epoxy Powder Coating. Apply as per manufacturer's application guide dated 'October 2018'. Cure for 5 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CanSEALER (CS1)-TS'. Site applied, colourless waterproofing sealer which can be applied to cement with a roller or a brush. Apply one coat with a roller or a brush as per manufacturer's Technical Data Sheet 'CS1-210002'. Cure for 36 days@5°C. When applied by brush the material is for use with water up to 23°C. When applied by roller the material is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TPU inner hose (YOUSHI/3017)'. Transparent, colourless, extruded TPU hose. For use with water up to 85°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Ultramid A3EG7 FC Aqua Black 23285'. Black coloured, injection moulded PA66 material. For use with water up to 65°C.
'Zytel® HTNFG52G35HSLR BK011'. Black coloured, injection moulded polyphthalamide (PPA) material. For use with water up to 85°C.
'Ultramid D3EG10 FC Aqua Black 23285'. Black coloured, injection moulded polyamide material. For use with water up to 65°C.
'Badadur PBT9 GF30 Natur S1' (appears cream in colour) and 'Badadur PBT9 GF30 grau 930a' (grey coloured). Natural or grey coloured, injection moulded, glass reinforced PBT materials. For use with water up to 85°C.
'Radius Systems Puriton Light Blue Barrier Pipe [Type A, BS8588]' (formerly known as 'Radius Systems Puriton II LB Pipe' until March 2025). Extruded, triple layered pipe consisting of a black coloured polyethylene inner layer, aluminium middle layer and blue coloured polyethylene outer layer. For use with water up to 23°C.
‘Xytron™ G4020DW-FC BK00001 & Xytron™ G3020DW-FC BK00001’. Black coloured, injection moulded PPS materials. In September 2023 ‘Xytron G4020DW-FC NA99001’, natural (appears beige), injection moulded PPS material was added to the approval. All are for use with water up to 85°C.
'TORELINA A673MB2'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'RH-PPR-32 Fitting'. Green coloured, injection moulded PPR fittings. For use with water up to 85°C.
'RH-PPR-32 Pipe'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'4270' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. In May 2024 ‘shaped seals’ (in-radius of 1.8mm) made in Italy, were added to the approval. In November 2024, lip seals (in-radius of 0.7mm) made in Italy, were added to the approval. For use with water up to 85°C.
'VL1713M266B Black'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.02mm. For use with water up to 85°C.
‘AA9HWZ (88 Sh.)’. Grades ‘AA6HWZ (60 Sh.), AA7HWZ (70 Sh.), AA7SWZ (70 Sh.), AA8HWZ (80 Sh.) were added in December 2022. Black coloured, compression moulded EPDM sheet materials. With a shore hardness of between 60 & 88. Tested in-radius size 1.15mm. For use with water up to 85°C.
'Silopren LSR 2630, 2640, 2650, 2660 & 2670'. Natural (appears clear), compression moulded silicone rubber sheet materials. Shore hardness between 30 & 70. Tested in-radius size of 1.0mm. For use with water up to 85°C.
'Innotec Thread Seal'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C.
Range of deck mounted, single hole, single outlet (fixed) electronically operated tap assemblies (Chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a tee piece for installation prior to the solenoid valve. The inlets of the tee piece incorporate a combined NBR gasket and stainless steel filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are also supplied with stainless steel braided PEX lined flexible (connecting) hose assemblies and angled spherical valves incorporating a stainless steel strainer for installation on each inlet. Temperature is controlled by adjusting the opening of each angled spherical valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a nickel plated DZR brass body. For use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC
Range of one-piece and two-piece pre-insulated GRP cold water storage cisterns. Cisterns are supplied with a float operated inlet valve, screened overflow and screened vent. Cold water use only.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc diverter headworks with or without a on/off function, to be installed in specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Manual diverter headwork incorporating a plastic body and silicone seals for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with brass bodies and EDPM ‘O’-rings. All models expect XB-12T incorporate stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies and EPDM ‘O’-rings. All models incorporate a plastic strainer. For insertion into specifically dimensioned bores. Maximum working pressure 16 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with a cross-top operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 32.825.00E and 32.883.000 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) Models F1025S, F5126 and F5122L incorporate a ceramic cartridge headwork with a single lever operating member All other models incorporate ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever, cross top or wheel operating members. The spout outlet incorporates a plastic aerator and the products are supplied with a click type pop-up waste. Maximum operating pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporate an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks with either single lever, dome or cross-top operating members. The spout outlets incorporate plastic aerators or flow straighteners with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disk headworks with single lever operating members. The cold water inlets is supplied with a chrome plated brass adapter incorporating an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate plastic aerators. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of two-hole, deck mounted single outlet (fixed) combination tap assemblies incorporating brass body (various finishes) and quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies incorporating brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aeator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Page 2 of 8
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
