Range of multistage vetical water pumps with stainless steel bodies and impellers incorporating EPDM ‘o’ rings and seals. With various nominal flow rates depending on number of impellers and inlet connection size. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

1910306

Expiry date:

31/10/2024

Marking:

WILO on pump body.

Installation Requirements:

R001 R415

Model:

MVIS Nominal flow rate - 2 m3/h with 2 to 10 impellers – inlet connection 1 1/4” BSP(F), 4 m3/h with 2 to 10 impellers – inlet connection 1 1/4” BSP(F) 8 m3/h with 2 to 6 impellers – inlet connection 2” BSP(F) The product name of the MVIS range for which approval is sought is built as: Example :MVIS403-1/16/K/3-400-50-2 Where: ‘4’ Nominal flow (m3/h) (other possible values are 2 and 8) ‘03’ Number of Impeller (other posible values see table above)) ‘-1’ Pump housing in stainless steel AISI 304 ‘/16’ Maximal pressure (bar) ‘/K’ EPDM material for O ring ‘/3-400-50-2’ Motor definition : Three phases 400 Volts-50 HZ 2poles MVISE range Nominal flow rate - 2 m3/h with 6 an 10 impellers – inlet connection 1 1/4” BSP(F), 4 m3/h with 4,6 and 10 impellers – inlet connection 1 1/4” BSP(F) 8 m3/h with 3 and 6 impellers – inlet connection 2” BSP(F) The product name of the MVIS range for which approval is sought is built as: Example :MVISE210-1/16/K/3-2-3G Where: ‘2’ Nominal flow (m3/h) (other possible values are 2 and 8) ‘10’ Number of stage (other posible values see table above) ‘-1’ Stainless steel AISI 304 ‘ /16’ Maximal pressure (bar) ‘/K’ EPDM material ‘/3-2-3G’ 3 phases 2 poles third generation of converter

Factor:

Wilo SE

Company Name

Wilo SE

Address

Werk Hof, Heimgartenstr. 1-3, 95030 Hof/Saale

View All Listings by this Company

Manufacturer:

Wilo Salmson France

Company Name

Wilo Salmson France

Address

80 Boulevard de l'Industrie CS 90527 F-53005 LAVAL Cedex

Phone

+33 2 43 59 54 00

View All Listings by this Company

Helix range of vertical stainless steel multistage pumps with various pump housing materials depending on pump configuration. Maximum working pressure 30.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2006300

Expiry date:

30/06/2025

Size:

DN50 - DN80

Marking:

Wilo on body.

Installation Requirements:

R001 R415

Model:

Helix V, Helix VE, Helix Excel ranges.

Factor:

Wilo SE

Company Name

Wilo SE

Address

Werk Hof, Heimgartenstr. 1-3, 95030 Hof/Saale

View All Listings by this Company

Manufacturer:

Wilo Salmson France

Company Name

Wilo Salmson France

Address

80 Boulevard de l'Industrie CS 90527 F-53005 LAVAL Cedex

Phone

+33 2 43 59 54 00

View All Listings by this Company

Luberpox – 2K – DS-Lackfarbe IV80, Wilo Grün nach Muster/IW80 Hardener (green coloured) & Luberpox – 2K – DS-Lackfarbe IV80, RAL 9011 Graphitschwarz/IW80 Hardener (black coloured). Factory applied epoxy coatings. Mix in a 5:1 weight ratio and apply as per Berger-Lacke Technical Data Sheet (rev. 41-06.11.2023). Cure for 7 days at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2311513

Expiry date:

30/11/2028

Manufacturer:

Wilo SE

Company Name

Wilo SE

Address

Werk Hof, Heimgartenstr. 1-3, 95030 Hof/Saale

View All Listings by this Company