D Line Approvals


#2106306

Range of shower heads and a shower handset. The shower heads have a stainless steel body and ball joint, silicon ‘O’-rings and nozzles, and the inlet incorporates a combined NBR washer and stainless steel filter. The shower handset has a stainless steel body, NBR ‘O’-rings and silicon nozzles. All products incorporate a plastic flow regulator on the inlet. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
WRAS Approval Number:
2106306
Expiry date:
30/06/2026
Note:
Open outlet use only.
Size:
QS5320xxx: ½” BSP (M). QS5100 & QS5110xxx: ½” BSP (F).
Marking:
QTOO (brand of D Line) on body.
Installation Requirements:
R001 R040
Model:
QS5100xxx - 200mm (overhead shower) QS5110xxx - 300mm (overhead shower) QS5320xxx (hand shower) Where xxx denotes the finish and can be replaced by 1 to 3 digits: M = brushed stainless steel finish. PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2106324

Range of wall or ceiling mounted shower arms and a wall mounted shower outlet + holder. The products incorporate a stainless steel bodies (various finishes). Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
WRAS Approval Number:
2106324
Expiry date:
30/06/2026
Note:
Open outlet use only.
Size:
½” BSP (M).
Marking:
QTOO (brand of D Line) on rosette.
Installation Requirements:
R001 R040
Model:
Ceiling mounted shower arms: QS5209xxx - 100mm. QS5219xxx - 200mm. QS5229xxx - 300mm. QS5239xxx - 400mm. Wall mounted shower arm: QS5279xxx - 300mm. QS5289xxx - 400mm. Wall mounted shower outlet + holder: QS5590xxx. Where xxx denotes the finish and can be replaced by 1 to 3 digits: M = brushed stainless steel finish. PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#1904085

Range of brass or stainless steel double interlocked hoses incorporating EPDM inner hoses. The hoses are supplied with EPDM gaskets. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
1904085
Expiry date:
30/04/2024
Size:
See model.
Marking:
QTOO (BRAND OF D LINE) ON FERRULE ferrule.
Installation Requirements:
R001
Model:
For DN 14 various brass end connectors: 1/2" knurled nuts - female 1/2" hexagonal nuts - female 1/2" smooth nuts - female 1/2" conical nuts - female 1/2" anti-twist conical nuts - female 3/4" knurled round nut - female 3/8" nuts - female 3/8" cylindrical connector - female 1/2" demountable connector - female 3/8 M 15 x1 M 12 x 1M For DN 15 various brass end connectors: 1/2" knurled nuts - female 1/2" hexagonal nuts - female 1/2" smooth nuts - female 1/2" conical nuts - female 1/2" anti-twist conical nuts - female 3/8 M For DN 17 brass end connectors: F1/2 x F1/2 Surface finishes: Raw Chromed Electropolished Polished Gold Bronze Copper Nickel ACR White Black Red Grey Silver Old brass Beige Green Yellow Orange Champagne Fumé Black metal Gun metal Model code key: QS5410XXX AAAA: identifies the type of external finish BBBB: identifies the type of fitting CCC : identifies the length (between 500 and 2000mm) Models Added January 2020: Stainless Steel (INOX) interlocked hoses and end connectors. Model code key: FXB2WX.AABBCCCC.DDD AA: identifies hose raw material and diameter BB: identifies the type of external finish CCCC: identifies the type of fittings DDD: identifies the length (between 50 and 200cm)
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2106319

Range of wall mounted, concealed, thermostatic shower blending valves incorporating stainless steel bodies, a 2-way ceramic disc headwork and a single lever operating member controlling the flow. The temperature is controlled independently via a thermostatic cartridge with a single lever incorporating a manual override operating member. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2010 Valves
Section Subtitle:
Blending, thermostatic.
WRAS Approval Number:
2106319
Expiry date:
30/06/2026
Note:
This approval does not include a shower hose and handset or overhead shower outlet.
Size:
½” BSP (F).
Marking:
QTOO (brand of D Line) on operating member.
Installation Requirements:
R001 R010 R040
Model:
QS3300 (concealed valve) which must be installed with the following operating member/trim sets: QA2290xxx (diverter control). QA2390xxx (thermostat control). Where xxx denotes the finish and can be replaced by 1 to 3 digits: M = brushed stainless steel finish. PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2110305

Range of spout outlets incorporating stainless steel bodies (various finishes) and a plastic aerator. Maximum operating temperature 60°C.

Section:
0682 Combination Tap Assemblies
Section Subtitle:
Spout outlets.
WRAS Approval Number:
2110305
Expiry date:
31/10/2026
Note:
Open outlet use only.
Size:
½” BSP (M)
Marking:
QTOO (brand of D Line) on rosette.
Installation Requirements:
R001 R040
Model:
QA3080xxx Spout 115mm, rose 80mm, 45 degree. QA3090xxx Spout 115mm, rose 90mm, 45 degree. QA3180xxx Spout 190mm, rose 80mm. QA3190xxx Spout 190mm, rose 90mm. QA3280xxx Spout 250mm, rose 80mm. QA3290xxx Spout 250mm, rose 90mm. QA3380xxx Spout 191mm, rose 80mm, 45 degree. QA3390xxx Spout 191mm, rose 90mm, 45 degree. Where xxx denotes the surface finish (which is a non-water contact part). It can be 1 to 3 digits, which can be any combination of numbers and/or letters, as examples: M = brushed stainless steel finish, PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2110364

Ragfe of single hole, single outlet (fixed) combination tap assembly with stainless steel bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator with an integral flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0450 Combination Tap Assemblies
Section Subtitle:
Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2110364
Expiry date:
31/10/2026
Size:
Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections.
Marking:
QTOO (brand of D Line) on operating member.
Installation Requirements:
R001 R006 R009 R010
Model:
QT1150xxx Single hole mixer. QT1151xxx Single hole mixer with short lever pin. Where xxx denotes the finish and can be replaced by 1 to 3 digits: M = brushed stainless steel finish. PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2110365

Single hole, single outlet (swivel) combination tap assembly (stainless steel body - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator with an integral flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2110365
Expiry date:
31/10/2026
Size:
Stainless steel braided PEX lined flexible hose assemblies incorporating ⅜” captive nut end connections.
Marking:
QTOO (brand of D Line) on operating member.
Installation Requirements:
R001 R006 R009 R010
Model:
QT1200xxx Tall single hole mixer. Model added June 2022 QT2100xxx Where xxx denotes the finish and can be replaced by 1 to 3 digits: M = brushed stainless steel finish. PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2209328

Premix control unit for an infrared sensor tap comprising of a solenoid valve with plastic body, EPDM diaphragm and ‘O’-rings, and silicone seals. Both the cold and hot inlets incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The central section of the valve incorporates a plastic strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.

Section:
2240 Valves
Section Subtitle:
Solenoid, plastic.
WRAS Approval Number:
2209328
Expiry date:
30/09/2027
Size:
½” BSP (M).
Marking:
QTOO (brand of D Line) on outer casing
Installation Requirements:
R001 R008 R010
Model:
QSF01
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2110306

Range of wall mounted, concealed, manual blending valves with a brass body incorporating a ceramic cartridge headwork with a single lever operating member. The QS3200 model also incorporates a manual diverter with a single lever operating member. The QS3400 model is a stainless steel bodied spout conector to be used in conjunction with the QS3100 and QS3200 concealed valves. Maximum working pressure 10.0 bar.

Non-metallic materials and components comply with BS6920 at 60°C

Section:
2000 Valves
Section Subtitle:
Blending, manually operated.
WRAS Approval Number:
2110306
Expiry date:
31/10/2026
Note:
This approval does not include a spout outlet, shower outlet or overhead shower. The QS3400 (spout connector) is not approved in its own right.
Size:
½” BSP (F).
Marking:
QTOO (brand of D Line) on operating member.
Installation Requirements:
R001 R010 R040
Model:
QT3100 (single outlet). QS3400 (spout connector) which must be used in conjunction with the following concealed valves: QS3100 (single outlet). QS3200 (two outlet).
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


#2305303

Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.

Non-metallic materials and components comply with BS6920 at 60°C

Section:
0684 Combination Tap Assemblies
Section Subtitle:
Non-touch Methods of Control Products listed in this section utilise flow control methods that do not require touch to activate.
WRAS Approval Number:
2305303
Expiry date:
31/05/2028
Note:
This product may not comply with the requirements of regulation 4(1)(b). Consult your local water undertaker prior to installation. R008 applies to the Premix control unit. The product is not supplied with any connecting hoses/pipework between the Premix control unit and the spout.
Size:
½” BSP (M) (to hot and cold inlets of solenoid).
Marking:
QTOO (brand of D Line) on spout trim.
Installation Requirements:
R001 R008 R010 R040 R570
Model:
QST3190xxx (190mm spout), QST3290xxx (250mm spout). Where xxx denotes the surface finish (which is a non-water contact part). It can be 1 to 3 digits, which can be any combination of numbers and/or letters. As examples: M = brushed stainless steel finish, PP1 = polished PVD gunmetal finish.
Factor:
D Line
Company Name
D Line
Address
Roskildevej 22 2620 Albertslund
Phone
+4572170138
General Email
service@dline.com

View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page of 1

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.