Stainless steel press fittings for use with 316L & 304 stainless steel tube incorporating EPDM ‘O’ rings. The fittings and tube are assembled using a crimping tool. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of Easytec press fittings for use with Easytec multilayer (Pe-rt/Al/Pe-rt) pipe. Hewing range of ‘Easytec’ Multilyer Composite Pipe and Press Fitting system with brass press fittings with stainless steel sleeves incorporating EPDM o-rings. 16mm to 32 mm are LBP fittings and from 40mm to 63 mm are standard fittings. Joints are achieved via TH profile press tool. Maximum working pressure: 10bar Maximum working temperature: 95°c
Range of Gerpex press fittings for use with Alpert multilayer (Pe-rt/Al/Pe-rt) pipe. Alpert Multilyer Composite Pipe and Press Fitting system with brass press fittings with stainless steel sleeves incorporating EPDM o-rings. 16mm to 32 mm are LBP fittings and from 40mm to 63 mm are standard fittings. Joints are achieved via TH profile press tool. Maximum working pressure: 10bar Maximum working temperature: 95°c
Range of brass bodied compression fittings for use with copper pipe(manufactured to EN1057). . Maximum working pressure 16.0 bar @ 30°C, 10.0 bar @ 65°C and 6.0 bar @ 100°C.
Range of copper and brass press-fit fittings with HNBR o-rings, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Conex >B< press fittings incorporating copper & brass bodies for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of end feed copper solder fittings for use with copper tube. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of urinal flushing mechanisms incorporating nylon bodies and a solenoid valve which controls the flow and is actuated via an infra-red sensor. The inlet of the solenoid valve incorporates a stainless-steel strainer. Maximum working pressure 5.0 bar. Cold water use only.
Range of stainless-steel plate heat exchangers. Maximum working pressure 10 bar. Maximum operating temperature 90°C.
‘G5 BC’ range of command centres that provide instant near boiling and chilled water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
‘G5 BCS’ range of command centres that provide instant near boiling, sparkling and chilled water (all filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products incorporate a pressure reducing valve (adjustable outlet pressure between 2.25 and 2.75 bar) on the supply to the carbonator unit. The carbonator inlet incorporates a non-return valve. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum inlet supply pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
Range of wall mounted combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system. The primary circuit incorporates a pressure relief valve set at 3.0 bar and an expansion vessel. The products are supplied with a temporary filling loop which incorporates a combined isolation valve and double check valve assembly (suitable for backflow protection against Fluid Category 3), stainless steel braided EPDM lined flexible hose assembly and an isolation valve. The secondary circuit (DHW) incorporates a stainless-steel strainer. The primary circuit incorporates isolation valves on the flow and return. Maximum working pressures: DHW: 10.0 Bar CH:2.5 Bar Maximum operating Temperatures: DHW: 65.0°C CH: 85.0°C
Range of wall mounted combination boilers providing domestic hot water via a heat exchanger and pressurised central heating system. The products can be supplied with a rigid or flexible filling loop or keyless filling link. The flexible and rigid filling loops incorporate a flexible hose or copper pipe, isolation valve, double check valve assembly (suitable for back flow protection against fluid category 3). The keyless filling link incorporates a CAB backflow prevention device (suitable for back flow protection against fluid category 3). The products also incorporate an expansion vessel and pressure relief valve set at 3.0 bar. Maximum working pressure of primary circuit 2.5 bar. Maximum operating temperature of primary circuit 85°C Maximum working pressure of secondary circuit 8.0 bar Maximum operating temperature of secondary circuit 60°C
Range of water meters with black epoxy coated bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of pressure, flow and temperature sensors. The VFI sensors have stainless steel bodies, all other models have plastic bodied sensors. The MFS and VFS models are supplied with a plastic (composite) or stainless-steel flow pipe. The VFI models are supplied with a stainless-steel flow pipe. The products can also be supplied with a range of fittings/end connections (see model and size). Maximum working pressures: ITS, LPS, RPS, MFS (composite flow pipe) and VFS (composite flow pipe) models: 24.0 bar. CPS models (added February 2024): 24.0 bar. DPS: Models with vent hole: 16.0 bar. All other models: 24.0 bar. MFS (stainless steel flow pipe) and MFS (stainless steel flow pipe): 30.0 bar. VFI non-flanged models: 30.0 bar. VFI flanged models: 30.0 bar or as per flange PN rating 16.0 bar or 25.0 bar (whichever is lower). Maximum operating temperature 99°C.
Permanent magnet variable frequency multistage pump with plastic bodies, plastic impellers, stainless steel shaft and EPDM ‘O’-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
CMBE range of horizontal multistage centrifugal booster pumps with stainless steel bodies and impellers and EPDM ‘O’-rings. All models include an expansion vessel, non-return valve, pressure gauge and sensor on the outlet. Maximum working pressure 10.0 bar. Cold water use only.
Range of vertical multistage pumps with either stainless-steel bodies (“N” versions) or cast iron bodies with a black electrodeposition coating (“G” versions), stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: NKV32 & NKV45 models - 32.0 bar, NKV65 & NKV95 models - 25.0 bar. Max operating temperature: Stainless steel (“N” versions) - 100°C. Cast iron (“G” versions) - Cold water use only.
Range of vertical multistage pumps with either stainless-steel bodies (“N” versions) or cast iron bodies with a black electrodeposition coating (“G” versions), stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: FGV30, FGV45 - 32.0 bar, FGV65, FGV95 - 25.0 bar. Max operating temperature: Stainless steel (“N” versions) - 100°C. Cast iron (“G” versions) - Cold water use only.
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of vertical multistage pumps with cast iron bodies with a black electrodeposition coating, stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: MVX 30 & MVX 45- 32.0 bar, MVX 65 & MVX95 VR - 25.0 bar. Cold water use only.
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of hand showers with (plastic bodies - various finishes). The products incorporate a stainless-steel strainer and flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted and ceiling mounted shower arms (chromium plated brass).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of shower heads with a chromium plated brass bodies, with stainless-steel strainer plastic flow regulator on the inlet. Models P42802 & P45300 have plastic bodies.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets with chrome plated plastic bodies. Some models incorporate a plastic aerator at the outlet of the shower and/or a plastic flow regulator and strainer on the inlet.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall and ceiling mounted shower arms with (brass bodies - various styles and finishes). Maximum operating temperature 60°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower rail kits, (chrome plated - plastic bodies) incorporating a shower handset, shower hose and adjustable shower rail. Maximum operating temperature 80°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 80°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of basin pillar taps (brass bodies - various finishes), incorporating self-closing headwork and a plastic aerator in the outlet. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of stainless steel braided, PEX lined flexible hose assemblies incorporating various end connections. The hoses are supplied with NBR O-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Multi-layer shower hose with a PVC inner hose, supplied with EPDM ‘O’-rings. Maximum operating temperature 60°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of shower hoses with TPE linings and EPDM ‘O’-rings. Maximum operating temperature 60°C. Open outlet use only.
'Hurricane' range of Indirect and direct unvented storage cylinders consisting of factory fitted single or twin coil circuit with either a primary or solar coil. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar@90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve adjustable between 2.7 and 3.3 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum supply pressure to the inlet control group 10.0 bar. Maximum working pressures: Secondary circuit 3.0 bar, Primary Circuit 3.0 bar & Solar circuit 5.5 bar. Maximum operating temperature 65°C.
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range of 2 and 3 port manifold assemblies with brass bodies incorporating ‘Tectite Classic’ push-fit fittings for use with either copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS7291-3:2010) or PB pipe (manufactured to BS7291-2). Maximum working temperature and pressure: Use with copper pipe: 16.0 bar @ 30°C, 10.0 bar @ 65°C & 6.0 bar @ 95°C. Use with PEX & Polybutylene: 12.0 bar @ 20°C, 6.0 bar @ 65°C & 3.0 bar @ 92°C.
Non-metallic materials and components comply with BS6920 at See description °C
6300E7 series of nickel plated brass manifolds and 6300R8 series of chromium plated brass manifolds with two, three or four outlets, for use with copper pipe (manufactured to EN1057). The products incorporate a screw down isolation valve at each port. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic bar shower mixers, (brass bodies – various finishes) incorporating quarter turn ceramic disc headwork controlling the flow with cubed or dome type operating members. The temperature is controlled independently via a thermostatic cartridge cube or dome type operating members incorporating a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed thermostatic blending valves with (brass bodies – various chrome plated trim sets). The flow is controlled by either a quarter turn ceramic disc headwork, a ceramic disc diverter valve or both using single lever or cubed type operating members. The temperature is controlled via a thermostatic cartridge using a cross-top, cubed or single lever operating members. The products incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate the is provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, bar type thermostatic shower mixer (chromium plated brass) Incorporating a quarter turn headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets and shower outlet incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models except model 521308, 521324, 521314 and 521318 incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C except for models CA-100827 & CA-100828 both 60°C
Range of concealed, wall mounted, thermostatic blending valves, (brass bodies, chrome trim sets). The products consist of detent headworks, two-way diverter cartridges and a thermostatic cartridges (see models). All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. The valves are either handwheel and gear operated (Models D371X and DL371X) or lever operated (Models D71X and DL71X). Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘J9’ (wafer type) & ‘L9’ (lug type) ranges of butterfly valves with blue epoxy coated ductile iron (128xxx) or stainless steel bodies (628xxx), stainless steel discs and EPDM seats. The products are supplied with either a lever, gearbox (below DN250), electric or pneumatic actuating operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. Gearbox and handwheel Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of wafer, lugged and double bridge type butterfly valves with blue epoxy coated ductile iron bodies, stainless steel or blue epoxy coated ductile iron discs and EPDM seats. JMC 31300/71300/61300 and PAR W/L/DF.112 models have stainless steel discs (DN50 to 250: ASTM CF3 M (1.4409) DN>250 ASTM CF8M (1.4408)); all other models have blue epoxy coated ductile iron discs. All valves are bare shaft without an operating member. Maximum working pressure 25.0 bar. Maximum operating temperature: JMC 31V00/71V00/61V00, PAR W/L/DF.P07 and PAR W/L/DF.112 models are 50°C. JMC 31W00/71W00/61W00 and PAR W/L/DF.P08 models are cold water use only.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of non return valves with bronze bodies and discs, and an EPDM washer. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of pressure relief valves with brass bodies and EPDM diaphragms. Pre-set pressures between 1.5 and 10.0 bar. Maximum operating temperature 85°C.
Range of inline spherical valves with brushed chromium plated brass bodies and balls, PTFE seats and NBR ‘O’-rings. The valves are intended to be actuated by a motor (not supplied), but can also be screwdriver operated. Maximum working pressures: ¼” to 1” = 40.0 bar, 1¼” = 32.0 bar, 1½” to 2½” = 30.0 bar and 3” = 25.0 Bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel-plated brass bodies and ball with a PTFE seat. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with DZR brass bodies, chromium plated brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges, EPDM gasket and ‘O’-ring. The valves operate via non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50: 25.0 bar, DN65-DN600: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of front loading commercial washing machines with flow controlled by solenoid valves and discharged via a type `AD` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with a dual layer composite supply hose (blue outer/black inner). Maximum working pressure 5.0 bar. Cold water use only
Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
Range of electronically controlled ion exchange water softeners (salt regenerated) for commercial and domestic use. Maximum working pressure 5.0 bar. Cold water use
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD DW Coating - Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix Base and Catalyst in a 3:1 volume ratio and apply as per manufacturer's 'Product Information Data Sheet No: 780', 'Revision: 00', 'Issue Date Feb-22'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HEMPADUR 85671 System'. Factory applied epoxy coating system comprising of a pink base coat (50900), light green middle coat (42070), and pink top coat (50900 - water contact). Each coat comprises of a base and curing agent to be mixed in a 8.8:1.2 volume ratio before applying in accordance with manufacturer's PDS dated January 2023. Cure each coat for 7 days@20°C and then 20 hours@40°C. For use with water up to 30°C.
'AG30E'. Black coloured, injection moulded PA66+GF30 material. For use with water up to 85°C.
'Vydyne R530 NAT'. Natural (appears light grey), injection moulded polyamide 66 (with 30% glass fibre) material. For use with water up to 23°C.
'PLUSTEK PB306G6BL151'. Blue coloured, injection moulded, polyamide material (30% glass fibre reinforced). For use with water up to 85°C.
'VYDYNE AG7K-BK1066'. Black coloured, (35% glass Fibre reinforced) polyamide 66 material. From 1st April 2023 until 29th May 2024, the material was for use with water up to 23°C. From 30th May 2024 until 30th April 2028, the material is for use with water up to 70°C.
'A280G6 HF'. Off-white coloured, injection moulded PA66-GF30 material. For use with water up to 80°C.
'Polimid A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'Revolve N307'. Blue coloured polyethylene material, manufactured by rotational moulding. For use with water up to 23°C.
'DIC.PPS Z-230 BLACK' (manufactured in Komaki (Japan), Penang (Malaysia), Vienna (Austria) & Zhangjiagang (China). ‘DIC.PPS Z-230 BLACK-U’ (manufactured in Komaki (Japan), Penang (Malaysia), Vienna (Austria) & Zhangjiagang (China) was added to the approval in September 2023. ‘DIC.PPS Z-230 BLACK-U1’ (manufactured in Vienna (Austria) was added to the approval in September 2023. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'PG6-S09'. Beige coloured, injection moulded PP+GF30 material. For use with water up to 85°C.
‘Estane® Grades 58887 Nat 036, 58315 Nat 033, 58300 Nat 036, 58887 Nat 029, 58315 Nat 055, 58887 Nat 038 & 58887 Nat 055’. Natural (transparent, colourless), injection moulded TPU materials. For use with water up to 23°C.
'Venda Tapafugas Blinker'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet '01-02-29R R4'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELASTOSIL LR 3020/60 A+B' Natural (appears white, translucent) & 'ELASTOSIL LR 3020/60 A+B with 2% by weight ELASTOSIL Colour Paste FL Red Iron Oxide RAL 3013' (red coloured). Injection moulded silicone rubbers with a shore hardness of 60 ShA and a tested in-radius size of 0.9mm. For use with water up to 85°C.
Range of single hole, single outlet, electronic touch free, deck mounted taps (chromium plated brass) for cold or premixed water. Flow is controlled via solenoid valves, actuated by infra-red sensors. Power is supplied by externally mounted 9V battery pack or 9V transformer. The inlet hoses have a stainless-steel strainer and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Range of push button ceramic cartridge headworks with a plastic body and EPDM seals. For insertion into specifically dimensioned tap assemblies Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Ceramic cartridge headwork with a plastic body, incorporating a silicone rubber ‘O’ ring. Maximum working pressure 10 bar. Maximum operating temperature85 °C
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with a permanently open type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with level operating members. The spout outlets incorporate plastic aerators. The products are supplied with click wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet is a waterfall type. The products are supplied with a click type pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Single hole, single outlet fixed combination tap assemblies (brass body - chrome finish), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates an aerator. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge. The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets for models (143106) incorporate plastic flow straighteners or a plastic aerator ,models (M33146E &153306) incorporate plastic flow straighteners & model (172306) incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C for models 179606F, 173606, 173606 MBK1, M33146E. Maximum working pressure 10 bar. Maximum operating temperature 65°C 143106, 153306, 172306
Wall mounted bath shower mixer with brass body (various finishes). Ceramic disc headwork with dome operating members, manually operated diverter to shower outlets. The temperature is controlled independently via a thermostatic cartridge using a single lever operating member. Both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Spout outlet incorporates a plastic aerator. Products are supplied with shower headhead, shower handset and shower hose. Maximum operating pressure 10 Bar. Maximum operating temperature 85°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly, (brass body - various finishes), incorporating quarter turn ceramic disc headworks with various operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener, and the shower outlet connection incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models are supplied with a shower hose and handset. The shower handset incorporates a plastic flow restrictor on the inlet. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlets incorporate a plastic aerator or flow straightener. The products are supplied with a shower hose and handset. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
A range of wall mounted two-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes see models), incorporating quarter turn ceramic disc headworks, dome type operating members and self-cancelling diverter to shower outlets. The temperature is controlled independently via thermostatic cartridges with dome type operating members. Both operating members incorporate a manual override. Spout outlet incorporates a plastic aerator. Products are supplied with shower hose, shower handset and overhead shower. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Two-hole, single outlet (fixed) combination tap assembly, (brass body - various finishes), incorporating quarter turn ceramic disc headworks with various operating members, and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The inlet to the shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models are supplied with a shower hose and handset. The shower handset incorporates a plastic flow restrictor on the inlet. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted spout assembly, (brass body – various finishes), incorporating a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of welded stainless steel (S30408 or S31603) pipes. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Filling loop assembly comprising of a spherical valve, stainless-steel braided EPDM lined flexible hose and a double check valve assembly ((suitable for backflow protection against fluid category 3) which incorporates a lever operated spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
“D” Range of stainless steel (304S31/316S11) press fittings for use with ‘DPX’ series 1 & 2 stainless steel (304S31/316S11) pipe. The fittings and tube are assembled using a crimping tool. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of JG Twist & Lock Speedfit push-fit fittings for use with JG Speedfit Layflat Polybutylene Barrier Pipe (BPB Pipe to BS EN 7291-2:2010), 'BPEX' Barrier Pipe.(BPEX Pipe to BS EN 7291-3:2010) and Copper Pipe to BS EN1057:2006 Max working pressure & operating temperature: 12.5 Bar at 20°C 6.0 Bar at 83°C
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of MM and MC press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with AIS XPERT multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Range of brass (Series 1000 & 1100) and DZR brass (Series 1100CZ) compression fittings, various finishes. For use with copper tube EN1057. Maximum working pressure 30.0 bar. Maximum operating temperature 100°C.
Range of copper and brass press-fit fittings with HNBR o-rings, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Supreme S16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of Effast PVC-u solvent welded and/or threaded fittings for use with PVC-u pipe manufactured to (EN1452-2). Maximum working pressure 16.0 bar. Cold water use only.
SATK Series 22 range of wall-mounted direct heat interface units providing heating and instantaneous hot water. The hot water is generated via a plate heat exchanger. Maximum working pressure of all water circuits (secondary hot water, primary and space heating) 10.0 bar. Maximum operating temperature 90°C.
ALTAIR V5 Type A3 range of inline and concentric water meters. Inline models have brass or plastic bodies, concentric models are available with DZR brass or plastic bodies, the MCI model has a plastic body. Incorporates a plastic strainer. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with DZR brass bodies and EPDM ‘O’-rings. The inlet incorporates either a plastic or stainless steel strainer (see model). The product is supplied loose fibre gaskets for installation on the inlet and outlet. Maximum working pressure 16.0 bar. Cold water use only.
Pentobox range of water meter manifolds with plastic bodies and an integral spherical valve on the inlet. The models incorporate a non-return valve, (not suitable for backflow protection). Compression models are for use with metric and imperial PE80 pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of hose assemblies. Models B0301-148036-000 & B0301-148038-000 comprise of a spherical valve, stainless-steel braided EPDM lined flexible hose and double check valve assembly (suitable for backflow protection against fluid category 3). Model B0301-148037-000 comprises of a double check valve assembly (suitable for backflow protection against fluid category 3), stainless-steel braided EPDM lined flexible hose and ‘T’ type spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of single and doubled sphered rubbered expansion bellows incorporating a variety of flanged end connections. Style 99 TUF also incorporates a threaded inlet connection. Maximum working pressure 16.0 Bar Model (99 SSHDC) Maximum working pressure 20.0 Bar Cold water use only.
Range of single and doubled sphered rubbered expansion bellows incorporating a variety of flanged end connections. Style 99 TUF also incorporates a threaded inlet connection. Maximum working pressure 16.0 Bar Model (99 SSHDC) Maximum working pressure 20.0 Bar Cold water use only.
Range of single and doubled sphered rubbered expansion bellows incorporating a variety of flanged end connections. Style UF1001 also incorporates a threaded inlet connection. Maximum working pressure 16.0 Bar. Cold water use only.
Range of single and doubled sphered rubbered expansion bellows incorporating a variety of flanged end connections. Maximum working pressure 16.0 Bar Cold water use only.
Range of single and doubled sphered rubbered expansion bellows incorporating a variety of flanged end connections. Maximum working pressure 16.0 Bar Cold water use only.
Range of circulating pumps with a bronze body, plastic impeller and EPDM gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of multistage centrifugal pumps, with stainless steel bodies (CRN models) or black coloured cataphoretic electrodeposition coated cast iron bodies (CR models), stainless steel sleeve and impellers. The products can be supplied with or without a sensor. Maximum working pressures (no. of stages in brackets): CR/CRN 95 (1-5): 16.0 bar. CR/CRN 95 (6-8): 25.0 bar. CRN 95 (9-12): 40.0 bar. CR/CRN 125 (1-4): 16.0 bar. CR 125 (5): 25.0 bar. CRN 125 (6-7): 25.0 bar. CRN 125 (8-12): 40.0 bar. CR 155 (1-4): 16.0 bar. CRN 155 (1-4): 16.0 bar. CRN 155 (5-6): 25.0 bar. CRN 155 (7-11): 40.0 bar. CR/CRN 185 (1-3): 16.0 bar. CR/CRN 185 (4-5): 25.0 bar. CR/CRN 185 (6-8): 40.0 bar. CR/CRN 215 (1-3): 16.0 bar. CR/CRN 215 (4-5): 25.0 bar. CR/CRN 215 (6-7): 40.0 bar. CR/CRN 255 (1-3): 16.0 bar. CR/CRN 255 (3-4): 25.0 bar. CR/CRN 255 (5-6): 40.0 bar. When a sensor is incorporated the maximum working pressure is as follows: 25.0 bar with either the IPS44 or VTU sensor, (unless they are used on a pump with a maximum working pressure of 16.0 bar, in this instance the lesser pressure applies). The MBS3000 sensor can be used on all models, the pump maximum working pressure applies. Cold water use only.
Range of ceiling mounted, shower outlets with chrome plated brass bodies, EPDM seals, stainless steel strainer and flow regulator in the inlets. Supplied with a flexible hose. Maximum working temperature 60°C
Range of shower outlets with brass bodies (various finishes). The products incorporate a stainless-steel strainer and flow regulator. Open outlet use.
Range of overhead shower outlets with (chromium plated - brass bodies). The inlets incorporate a stainless-steel strainer and flow regulator. Model FLS-8120 Incorporates a shower arm.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets, (plastic bodies - various plated finishes). All models incorporate a flow regulator on the inlets. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Flow switch with a black plastic (nylon) body and an EPDM ‘O’-ring. The product incorporates a plastic filter on the inlet. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of nylon braided hoses with TPSiV inner liner and brass end connections incorporating EPDM washers.Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with a cube operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C except for models 623224 & 623229 both 60°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with handwheel gear operating members. Maximum working pressure – 10 bar or 16 bar, see models. Maximum operating temperature – 23°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating) and EPDM seats. Supplied with a rotating wheel operating member. Maximum working pressure:10Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer type & lug type butterfly valves with blue epoxy coated ductile iron (V9911 & V9912) or stainless steel bodies (V9952), stainless steel discs and EPDM seats. The products are supplied with either a lever, gearbox (below DN250), electric or pneumatic actuating operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of swing gate non-return valves (resilient trim) with bronze bodies, brass or bronze swing gate with nitrile rubber gasket. Maximum working pressure: 25.0 Bar. Maximum operating temperature: 85.0°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of swing gate non-return valves with blue epoxy coated ductile iron bodies and EPDM discs. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Inlet control group consisting of an in-line pressure reducing valve (adjustable pressure - see model) and a pre-set expansion relief valve (pre-set pressure - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe EN1057 only. Maximum supply pressure 10.0 bar. Maximum operating temperature 40°C.
Range of pilot operated, pressure reducing valves with blue epoxy coated ductile iron bodies, stainless steel filter, EPDM ‘O’-rings and diaphragm. The valve has an adjustable pressure reducing facility controlled via a pilot valve, with auxiliary components including stainless steel tubing and fittings, and stainless-steel spherical valves. Maximum inlet supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 1.0 - 12.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
‘3029’ range of lever operated spherical valves with chromium plated brass bodies and balls, incorporating PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of commercial, salt regenerated, electronically controlled ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's 'Preparation and Curing Conditions' instructions reference 'ZX-9-1', dated '2024/02/26'. Cure for 30 minutes@180°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
KARUMEL EX4413-F103. Factory applied, fusion bonded, epoxy powder coating available in blue or red. Apply and cure in accordance with 'Application Guide KARUMEL EX4413-F103', issue 'KCSA-230201', dated February 2023, (curing as per Section 3.6). For use with water up to 85°C.
'SGPAM-CN-WB01'. Factory applied, blue coloured water based coating. Apply as per manufacturer's TDS 'PAMPIPE-TDC-WA04', version '4', dated '16/11/2022'. Cure for 30 minutes@50°C. For use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORROPOXY-FGE400'. Factory applied, red coloured, two-component epoxy coating. Mix and apply as per manufacturer's Application Procedures 'CPE/ FGE-400/Procd. /02', 'issue no - 03', dated '12.05.2022'. Cure for 30 minutes@45°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HDPE2300XM hose'. Off-white coloured (semi-translucent), extruded PEX-b hose. For use with water up to 85°C.
'PANG30'. Black coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.
'Vydyne A 30 GF Black WR'. Black coloured, 30% glass fibre reinforced, injection moulded PA66 material. For use with water up to 85°C.
'EPDM 30114010102A Black'. Black coloured, compression moulded EPDM sheet material. Shore hardness 75. Tested in-radius size 3.0mm. For use with water up to 85°C.
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6310522/20'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Griffon UNI-100 XT'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6300427', issue '1'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of break tanks and pump sets incorporating a Type AB airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10 bar. Cold water use only.
Range of AB air gap arrangements (verified by test - suitable for backflow protection against Fluid Category 5), supplied with or without softeners and/or flow meters (see models). Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Range of ceramic cartridge headworks with plastic bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies incorporating silicone seals, for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-out spray type which incorporates a nylon braided flexible hose incorporating a dual layer inner hose consisting of PEX inner layer and HDPE outer layer, and a manually operated button to divert between a plastic aerator and the spray function. The spray handset incorporates an approved check valve cartridge with an integral plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Wall mounted single hole, single outlet, combination tap assembly (chromium plated brass) incorporating a ¼ turn ceramic disc headwork with a cross top operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. SL-T10802 and SL-T10802M have open outlet spouts. All other models incorporate plastic aerators. Maximum working pressure 6.0 Bar. Maximum operating temperature 65.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spouts incorporate a waterfall outlet. The inlets incorporate a plastic flow regulator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate either a plastic aerator or flow straightener (see models) Model: 62783-7301, the inlets incorporate a plastic flow regulator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. Model (SL-T10805/B) has an open outlet spout. All other models incorporate plastic flow straightener, except SL-T10805. The product is supplied with metal back nuts. Maximum working pressure 6.0 Bar. Maximum operating temperature 65.0°C.
Range of two-hole, wall mounted (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Wall mounted, two hole, single outlet combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and manually operated diverter to shower outlet. The diverter is operated via swivel of the spout outlet. The spout outlet incorporates a plastic aerator. Both inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is not supplied with shower hose and handset. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating quarter turn cermic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with shower hoses, handsets and metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn headworks with various type operating members and a manual diverter to shower outlet. The spout outlets incorporate either a plastic flow straightener or plastic aerator. Model (173605) has an open outlet type spout. The products are supplied with metal backnuts, shower hose and handset. Maximum working pressure 10 bar. Maximum operating temperature 65°C but 70°C for models 173605, 173605 MBK1 and M33145E
Range of two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with lever type operating members. The spout outlet incorporates a plastic aerator. This products are supplied with a click-type pop up waste. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks and dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of expansion vessels with stainless steel bodies and EPDM membranes. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of filling loop assemblies, consisting of either a stainless steel braided, EPDM lined flexible hose assembly (300616 VIS and 300614 VIS) or a rigid copper tube assembly (3006315 VIS), a lever operated spherical valve and an in-line, non-verifiable double check valve assembly verified by test (suitable for backflow protection against fluid category 3) which incorporates an integral lever operated spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C , and 85°C for 300615 VIS.
‘Uponor S-Press Plus’ compatible pipe and fittings system consisting of Uponor MLC pipe and Uponor Uni Pipe for use with Uponor S-Press plus metal and PPSU fittings. Maximum working pressure and operating temperature: 10.0 bar@70°C. Maximum working pressure and operating temperature: 16.0 bar @ Cold water use only.
Range of stainless steel press-fit fittings and pipes, the fitttings incorporating stainless steel bodies and EPDM O-ring. Joints are made using a pressing tool for M profile. All the models are for both above ground and below ground use. YHPFM304 models are made of SS304 stainless steel, used with Yuhe SS304 pipes manufactured to EN10312. YHPFM316L models are are made of SS316L stainless steel, used with Yuhe SS316L pipes manufactured to EN10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of stainless steel press-fit fittings (316L or 304) and pipes (SUS316L or SUS304 - EN 10312), the fitttings incorporate EPDM O-rings. Crimp joint is achieved by a M profile crimp jaws. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Geberit range of ‘FlowFit’ press Fittings for use with ‘Geberit FlowFit Pipe ML’ and ‘Geberit FlowFit Pipe coils ML’ (insulated and uninsulated) PERT/Al/PERT pipes. The fittings are made from PPSU or lead free silicon bronze. Operating parameters: 16.0 bar@cold water and 10.0 bar@70°C.
Range of press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with Multitubo multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
‘Tweetop system’ consisting of brass bodied nickel plated, compression or press fit (‘U’ crimping profile) fittings for use with ‘Tweetop multilayer pipe’ PERT/AL/PERT. Maximum working pressure 10.0 Bar. Maximum working temperature 95°C.
‘Hetta system’ consisting of brass bodied nickel plated, compression or press fit (‘U’ crimping profile) fittings for use with multilayer pipe PERT/AL/PERT. Maximum working pressure 10.0 Bar. Maximum working temperature 95°C.
Instantor range of brass compression fittings for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
SAB A16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
FloPlast "Supreme" range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
NORMA MARLIN range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of Talbot pushfit fittings with polyprolylene or acetal bodies and EPDM o-rings for use with MDPE PE80 pipe (BS EN 12201). For use above and below ground use. Maximum working pressure 16 bar. Cold water use only.
‘AquaGas M range’ of copper and brass press fit fittings with NBR ‘O’-rings for use with copper tube (manufactured to BS EN 1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘DELBRAZE’ range of copper and copper alloy braze fittings for use with copper pipe (EN1057). Maximum working pressure: 16 bar. Maximum working temperature: 85°C.
Range of pipe repair clamps incorporating EPDM double seals. The products are intended for use with stainless steel pipe manufactured to EN1124. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of plate heat exchangers with stainless steel plate bodies and copper brazing. Maximum working pressure: 45 Bar. Maximum operating temperature: 99 °C.
Range of packaged plate heat exchangers comprising of stainless steel plates with EPDM gaskets. The products are supplied with twin primary circulation pumps, a secondary circulation pump, 3 port control valve and a control panel with full Mod BUS BMS connectivity. Maximum working pressure - Primary and Secondary circuits 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system incorporating an expansion vessel, pressure relief valve set at 3.0 bar and flow regulators. The inlets to both domestic hot water and primary circuits are controlled via screwdriver operated angled spherical valve. The primary circuit can be filled via a built in CAB device, that has been verified by test (suitable for backflow protection against Fluid Category 3). Primary circuit: Maximum working pressure 2.5 bar. Maximum operating temperature 80°C. Secondary circuit: Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of integrated water circuits with plastic bodies and EPDM ‘O’ rings and gaskets. The assemblies incorporate flow switches, plate heat exchangers and plastic flow regulators. The primary circuit incorporates a 3.0 bar rated pressure relief valve. Maximum working pressures: 2.5 bar primary circuit, 10.0 bar secondary circuit. Maximum operating temperature 85°C.
Range of water meters with epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of electromagnetic water meters with blue epoxy coated aluminium bodies and a natural rubber liner. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
“CZ 3000” range of water meters with brass bodies and plastic turbines. The inlets incorporate plastic filters. The outlets are fitted with approved check-valve cartridges (however, the complete product has not been fully tested for and is not intended to provide backflow protection). Maximum working pressure 16.0 bar. Maximum operating temperature 30°C.
Range of in-line ultrasonic water meters with DZR brass bodies and a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of two stage horizontal water pumps with plastic bodies, stainless steel impellers and shaft, incorporating EPDM gaskets and seals. The products also incorporate a non-return valve (not suitable for backflow protection) and an shock arrestor expansion vessel. Maximum working pressure 1.8 bar. Cold water use only.
‘SCALA1 TWIN’ range of booster pump sets, comprising of two pumps with plastic bodies, plastic impellers, EPDM and NBR ‘O’-rings and an accessory set consisting of a base plate, plastic manifold and four brass spherical valves. Each pump incorporates a non-return valve. Maximum working pressure 8.0 bar. Cold water use only.
Range of electronic steaming ovens with flow controlled via solenoid valve. Maximum working pressure 6 Bar Cold water use
Range of ‘Y’- pattern strainers with brass bodies incorporating stainless steel filters and EPDM ‘O’-rings. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps with (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members (SL-T30) or non-rising spindle headworks with cross top operating members (SL-T40). The spout outlet incorporates a plastic aerator (SL-T30) or a flow straightener (SL-T40407). The products are supplied with metal back-nuts. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of pillar taps with (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members (SL-T30) or non-rising spindle headworks with cross top operating members (SL-T40). The spout outlet incorporates a plastic aerator (SL-T30708X) or a flow straightener (SL-T40408). The products are supplied with metal back-nuts. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of plastic shower hoses with a PEX inner liner and external PVC outer in various finishes (see model). Maximum operating temperature 65°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of PVC or EPDM lined shower hoses with stainless steel outer (chrome or black finish) or PVC reinforced (chrome plated finish) outer layer. Maximum operating temperature 65°C.
Range of shower hoses with a rubber outer layer (various finishes, see models) and either PVC or PEX inner liner (see models), EPDM or NBR O-rings (see models) and either brass or stainless-steel connectors (see models). Open Outlet use only. Maximum operating temperature 85.0°C
Range of wall mounted, manually operated, blending valves with (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed thermostatic shower valves (brass bodies – various finished trim sets). All models comprise of an iBox that can consist of the following combinations. iBox incorporating a thermostatic cartridge with a dome type operating member. iBox incorporating a thermostatic cartridge with a dome type operating member and a detent headwork with a push button operating member to a shower outlet. iBox incorporating a thermostatic cartridge with a dome type operating member and two detent headworks with push button headworks to multiple shower outlets. iBox incorporating a thermostatic cartridge with a dome type operating member, two detent headworks with push button operating members to shower outlets and an internal shut off valve. All models incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C Models added December 2024: Maximum operating temperature 60.0°C
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of double flanged, handwheel operated butterfly valves with blue epoxy coated ductile iron bodies, incorporating either stainless-steel or blue epoxy coated ductile iron discs and EPDM seals. Maximum working pressure 16.0 Bar (DN50 to DN300) or 10.0 Bar (DN350 to DN2000) Maximum operating temperature 23.0°C
Range of concealed diverter valves with (brass bodies), incorporating a ceramic disc diverter. The product can be supplied with a trim set and dome, lever or cross top type operating members (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of full-bore spherical valves with bronze bodies, PTFE seats incorporating redox coated brass ball and various operating members (see models). Maximum working pressure 40 Bar Maximum operating temperature 95°C
Range of spherical valves incorporating a bronze body, brass or stainless-steel ball and single lever operating member. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 82°C
Range of spherical valves incorporating a bronze body, brass ball and butterfly lever operating member. Maximum working pressure 25.0 bar.
Non-metallic materials and components comply with BS6920 at 82°C
Range of TH profile pressfit brass bodied spherical valves with brass balls, EPDM O-rings and lever type operating members. Fittings for use with EN ISO 21003 Pert-al-Pert Multilayer pipe. Maximum working pressure 10 bar. Maximum operating temperature 95°C.
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball, (DZR brass body and ball on FFDZR prefix models). Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
“CN Pressure vessel” range incorporating a HDPE liner. The products have a separate outer layer (with black, blue, grey or natural finishes). The CN Pressure vessel 24x72” D-4 model has a top and bottom opening. Maximum operating pressure 10.5 bar. Cold water use only.
'DURACON®M90-44 WK3068'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per Kluber Lubrication product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KORASILON® Paste hochviskos' & 'KORASILON® Paste M-S 2-200'. White coloured (translucent) lubricants. Apply as per manufacturer's Product Data Sheet '30.01.2023'. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 TM-Z1 grau 930a'. Grey coloured, injection moulded polybutylene terephthalate material. For use with water up to 85°C.
'Badadur PBT9 GF10/GK20 grau 930a'. Grey coloured, injection moulded PBT material. For use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
'ML 57302'. Black coloured, compression moulded EPDM material. Shore hardness 55A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘ME2020’ injection moulded components. Silicone rubber ‘O’ rings and gaskets available in red, blue, white, black, light grey colours. Shore hardness between 30 - 70. Tested in-radii sizes between 0.5mm and 5mm. For use with water up to 85°C.
‘LS40T-0301, LS50T-0301, LS60T-0301, LS70T-0301 & LS80T-0301’. Injection moulded, liquid silicone rubber sheet material, available in white, grey, black, blue, green, natural (unpigmented) & red colours. Shore hardness between 40SH-A & 80SH-A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'kSil GP200, kSil GP250, kSil GP350, kSil GP400, kSil GP450 & kSil GP530'. Pale yellow/white coloured, extruded silicone rubber cellular sponge materials. Shore hardness between 37 & 70. Tested in-radii sizes between 1.53mm & 1.76mm. For use with water up to 85°C.
'HCR 9230, HCR 9250, HCR 9270 & HCR 9280'. Natural (appear white, translucent), compression moulded silicone rubber materials. Shore hardness between 30 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EFFAST PRESSURE PVC Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6313369/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Durapipe RH PVC-U Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6311355/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PLIMAT PVC Pressure Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6311689/30'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and model AF 1602 incorporates a plastic aerator in the spout outlet. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies, (chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
WC flushing cistern incorporating a side entry BS 1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Type ‘AB’ air gap arrangements (verified by test - suitable for backflow protection against fluid category 5) consisting of an inlet hose and solenoid valve on the inlet supply. Maximum working pressure 10.0 Bar Maximum operating temperature 55.0°C
Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with two test ports. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Thermostatic cartridge with NBR ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination taps assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: See models. Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks and lever operating members. The spout outlet incorporates a plastic aerator. Models:11 020 xx0 & 11 025 xx0 are supplied with a lever type pop up waste kit – Not verified by test. Models 11 021 XX0 & 11 035 xx0 are supplied with permanently open waste sets – Not verified by test. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators, flow straighteners, stainless steel strainers or open outlet type spouts (see models). Some models are supplied with a click type pop-up wastes, that have been verified by test (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Wall mounted two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating detent headworks controlling flow to either bath or shower. A thermostatic cartridge controlling the temperature incorporating a manual override button. The spout outlet incorporates a plastic aerator. Inlets incorporate a approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose, handset and overhead shower. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and manually operated diverter to shower outlet. The spout outlets are open out or incorporate a plastic flow straightener. Model SL-T40411 incorporates a non-rising spindle headwork with cross-top type operating members. Products are supplied with metal back nuts, hoses and shower handsets. Maximum working pressure 6.0 Bar Maximum operating temperature 60.0°C
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body - various finishes). The products incorporate 1/4 turn ceramic disc headworks with single lever, dome type, cubed or cross top operating members. The spout outlets incorporate plastic aerators. The products are supplied with stainless steel braided PEX lined flexible hose assemblies for connection between the side valves and the spout and click type pop-up wastes (verified by test). Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, three-hole, combination tap assemblies, (various finishes - see model), comprising of two ceramic cartridge headworks each with a single lever operating member. The product is supplied with stainless steel braided thermoplastic silicone (TPSiV) lined flexible connection hoses and a nylon braided silicone lined flexible hose assembly, which connects to a shower hose (brass double interlocked, PEX lined) and a deck mounted shower handset. Spout not supplied. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Zilmet range of cylindrical or tubular expansion vessels, epoxy coated carbon steel bodies with either Butyl or EPDM membranes and stainless-steel or galvanized carbon-steel connections. Please refer to models for maximum working pressures, as this varies by model and size. Maximum operating temperature 65°C.
Range of horizontal and vertical expansion vessels with EPDM membrane and stainless-steel connections. Maximum working pressure: 8.0 bar (35 litre model); 10.0 bar (50 litre up to 400 litre models).
Range of AIS tin-plated brass and PPSU press fit fittings for use with WRW & 'Maincor MLC’ multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Hep2O range of polybutylene fittings for use with Hep2O PB barrier pipe. In May 2024, Next generation (G5) of Hep20 pushfit fittings for use with the Hep20 range of PB barrier pipe, were added to the approval. Maximum working pressure 10.0 bar at 95°C.
Range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings and pipe. Fittings incorporate EPDM ‘O’-rings Maximum working pressure 10 bar. Maximum operating temperature 95°C
Inoxpres range of stainless-steel crimp fittings with EPDM ‘O’-rings and gasket for use with Inoxpres stainless-steel tube (1.4404 AISI 316L or 1.4521 AISI 444 – annealed or not-annealed). The connection is created by using a pressing tool. For above and below ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
Range of copper, bronze or DZR brass capillary solder ring fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure and operating temperatures: 8-28mm: 25.0 bar @ 30°C, 16.0 bar @ 100°C. 35-54mm: 25.0 bar @ 30°C, 16.0 bar @ 65°C and 10.0 bar @ 100°C.
‘SR’ range of capillary solder ring copper fittings for use with copper tube EN1057, for above ground use only. Maximum working pressure: 25.0 bar. Maximum operating temperature: 85°C.
‘SharkBite’ range of brass push fit fittings incorporating an EPDM ‘O’-ring. For use with the following pipes: JG Speedfit Layflat Polybutylene Barrier Pipe (JG BPB pipe manufactured to BS EN 7291-2:2010), 'BPEX' Barrier Pipe (JG BPEX pipe manufactured to BS EN 7291-3:2010), Polybutylene barrier pipe (manufactured to BS EN 7291-2:2010), PEX barrier pipe (manufactured to BS EN 7291-3:2010) and Copper pipe (manufactured to BS EN1057:2006). Maximum working pressures and operating temperatures: When used with Polybutylene barrier pipes (manufactured to BS EN 7291-2:2010) and PEX barrier pipes (manufactured to BS EN 7291-3:2010): 12.5 bar, cold water use only. 6.0 bar @ 95°C. When used with copper pipe (manufactured to BS EN1057:2006): 10mm sizes: Maximum working pressure 16.0 bar. Cold water use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. 15-22mm sizes: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C. 28mm size added April 2024: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
IDC ‘BDGxxx’ range of press fittings with brass or nickel plated brass bodies (see model) incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). The BDG241 and BDG257 prefix models incorporate an EPDM gasket on the captive nut end connection. Pressfit jointing is achieved by either a U or TH crimping profile. Compression connections are for use with copper pipe 12-28mm (manufactured to EN1057) or Irish copper pipe 14.7-27.4mm (manufactured to EN1057). For above ground use only. Maximum working pressure 10.0 bar. 20, 25 & 26mm pressfit sizes cold water use only. Threaded, compression and 16 & 32mm pressfit sizes maximum operating temperature 95°C. From June 2025: The 20, 25 & 26mm pressfit sizes (TH profile only) maximum operating temperature 95°C.
MecFlow Press (PPSU & Brass) Ranges of press fittings for use with MecFlow Press pipes. Maximum working pressure 10.0 bar. The maximum operating temperature is 95oC.
Range of end feed copper fittings for use with copper tube manufactured to EN1057, for above ground use only. Maximum working pressure 25.0 bar. Maximum operating temperature 85℃.
Range of plate heat exchangers with pressed stainless steel plate bodies and copper brazing. Available with threaded or flat face seal connection (see model). Maximum working pressure varies by model: ZT190 & ZT207 - 8.0 bar; ZB190, ZB195, ZB200, ZB207 & ZB315 - 10.0 bar; ZC315 (flat face seal version only) - 16.0 bar; ZC190, ZC207, ZC315 (threaded only) & Z(B-C-E) 250, 400, 450, 500 – 30.0 bar or 45.0 bar (models with additional upper and lower plates only); ZB600 & ZB700 - 30.0 bar. Maximum operating temperature 99°C.
Range of water meters with black epoxy coating bodies, plastic impellers and EPDM ‘O’ rings. Maximum working pressure – 16.0 Bar. Cold water use only.
Ultrims Ultrasonic range of in-line water meters with brass or plastic (-01 suffix models) bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
`UPM3` range of single stage circulator pumps, with stainless steel or plastic bodies, plastic impellers, ceramic shafts and bearings, EPDM 'O'-rings and seals. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: MH Three phase models 85°C, MH Single phase models 55.0°C and EH sp models 35°C.
Range of vertical submersible multistage pumps with either threaded or flanged end connections. Maximum operating temperature 23°C. Open outlet use only.
Range of Shower handsets with plastic bodies (chrome plated). The overhead showers incorporate a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Range of shower arms, hand shower holders and wall outlet with brass bodies (various finishes). Maximum working pressure: Open outlet. Maximum operating temperature: 60°C.
Range of shower arms and ceiling connectors (brass bodies – various finishes) & overhead shower outlets (plastic bodies - various finishes), incorporating EPDM O rings, plastic flow regulators and stainless-steel strainers. Open outlet use only Maximum operating temperature 60.0°C
Range of shower arms and ceiling connectors (brass bodies – various finishes) & overhead shower outlets (plastic bodies - various finishes), incorporating EPDM O rings, plastic flow regulators and stainless-steel strainers. Open outlet use only. Maximum operating temperature 60.0°C
Range of shower outlets comprising of shower handsets (brass bodies – various finishes) and overhead showers (stainless-steel bodies – various finishes), incorporating stainless-steel strainer washer. Model (CPH05013) incorporates a flow limiter in the inlet. Maximum operating temperature 85°C.
Range of shower outlets incorporating brass bodies (various finishes) and NBR ‘O’-rings. Maximum operating temperature 85°C.
Range of chromium plated brass shower outlets, shower arms and ceiling connectors. Model 26 034 xxx is supplied with a shower arm, and model 26 035 xxx is supplied with a ceiling connector. Maximum operating temperature 60.0°C. Open outlet use only.
Range of shower handsets with plated plastic bodies (various finishes). The inlet incorporates a plastic strainer. Maximum operating temperature 60ºC.
Range of pillar taps (brass bodies – various finishes) incorporating a quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar, Maximum operating temperature 65°C.
Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals. Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and an approved check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum working pressures: Primary: 3.0 Bar Secondary: 5.5 Bar Solar: 3.0 bar Maximum operating temperature 90.0°C
Wall mounted, manually operated concealed blending valve, incorporating ceramic cartridge headwork with single lever operating member. The valve incorporates copper pipe which connects the inlets and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic shower valves, (chromium plated brass), incorporating a thermostatic cartridge which controls both flow and temperature. All models have a single lever operating member controlling the flow and either a single lever operating member controlling the temperature. 86005660 does not include a manual override button on the temperature control. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of wall mounted, exposed, thermostatic shower valves (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. The products are supplied with 15mm compression inlet elbows incorporating approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate plastic flow regulators. The 90033CP model can have either a top or bottom outlet, which is achieved by re-positioning the blanking plug and threaded outlet. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
A range either concealed or exposed wall mounted thermostatic mixing valves with brass bodies (exposed models are chromium plated). Incorporates ¼ turn ceramic disc headworks. The inlets of all models expect F3004 incorporate stainless steel filters and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer and lugged butterfly valves with blue epoxy coated ductile iron bodies and stainless steel disc. DN50-DN300 are lever operated and DN350 – DN600 are handwheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of angle valves (brass bodies – various finishes), incorporating non-rising spindle headworks with a dome type operating members and NBR O-rings and PTFE Seals. Maximum working pressure 10 bar. Maximum operating temperature – Cold Water Use
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls and various operating members (see models). Products incorporate EPDM O-rings and PTFE seats. Maximum working pressure ½” – 1” 30 bar, 1 ¼” – 2” 25 bar. Maximum operating temperature 100°C.
Range of lever operated spherical valves with brass bodies (chromium plated), incorporating chromium plated balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly operated spherical valves with brass, DZR brass or nickel-plated brass. Incorporating brass or nickel-plated brass ball. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of full port spherical valves with DZR brass bodies, chrome plated or (VIR REDOX) coated brass ball (see model). The products are either lever or handle operated (see model). The 33FFDRE models include a stem extension. Maximum working pressure 32.0 bar. Maximum operating temperature 100°C (wholesome water use), 130°C (closed circuit use only).
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy ductile iron bodies and wedges incorporating PTFE seals and a non-rising spindle (16Q models) or outside screw and yoke (125Q models). The valves incorporate a handwheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with blue epoxy coated ductile iron bodies, incorporating EPDM ‘O’-rings and PTFE washers. Available in the following options: DN65-DN150 sizes: DZR brass sleeve. DN65-300 sizes: blue epoxy coated ductile iron sleeve. DN65-DN150 sizes: bronze disc. DN65-300 sizes: blue epoxy coated ductile iron disc. DN200-DN300 sizes: Stainless steel (SUS304) disc. DN200-DN300 sizes: Stainless steel (SUS304) stem. DN65-DN300 sizes: Stainless steel (SUS420) stem. DN65-DN150 sizes: brass stem. The product incorporates a test port on each flange and are adjusted using a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of bedpan washing & disinfection machines. The flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure - See models Maximum operating temperature - 90 °C
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'JERLAC Bituminous sealer coat black'. Factory applied, black coloured Bitumen coating. Apply as per manufacturer's TDS reference 'BN433', dated '27/07/2023', revision '00'. Cure for 12 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline® Defend 630 Cure 72', blue coloured coating. Between February 2024 and April 2025, the blue coloured coating was for use with water up to 50°C. Between May 2025 and February 2029, the blue coloured coating is for use with water up to 80°C. In May 2025, 'Hempaline® Defend 630 Cure 72', white coloured coating was added to the approval. For use with water up to 80°C. Factory applied, two-part epoxy phenolic coatings consisting of a base and curing agent. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's Product Data Sheet dated May 2025. Cure for 6 days@20°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JERLAC Solventless Epoxy Grey'. Factory applied, grey coloured, two-component Epoxy coating. Mix Base:Curing Agent in a 2:1 volume ratio and apply as per manufacturer's TDS reference 'BN434', dated '24/07/2023', revision '00'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Ziac Trattamenti Metallici SNC' instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NAVCOAT-001 HT'. Factory applied, black coloured bitumen based paint. Apply as per manufacturer's data sheet 'NCB/001', issue date '12.07.2023'. Cure 7 days@30°C. For use with water up to 60°C.
'Loctite EA 109'. Factory applied, grey/beige coloured, heat cured epoxy coating. Apply as per manufacturer's TDS for Loctite ESP109 (product has changed name) dated July 2007. Cure for 2 hours@130°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ES 988 DWPU'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv2.17102018'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur-Combiflex® SG System’ comprising of ‘Sikadur® 31 DW’ epoxy adhesive to be used in conjunction with ‘Sika Combiflex® SG Membrane’. ‘Sikadur® 31 DW’ is a site applied, grey coloured, two-part epoxy adhesive consisting of Part A (white coloured) and Part B (black coloured). Part A and Part B are mixed in a weight ratio of 3:1, applied and cured for 14 days@30°C. ‘Sika Combiflex® SG Membrane’ is a modified flexible Polyolefin (FPO) waterproofing tape to be applied over the adhesive and is approved as the water contact layer. Apply as per ‘Sikadur-Combiflex® SG System’ System Product Data Sheet, ‘Edition: 24/10/2012, Identification no: 02 07 03 02 System, Version: GCC’. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polimid A30GF Natural WR'. Natural (light grey coloured), injection moulded PA66 material. For use with water up to 85°C.
'TECHNYL ® SAFE C 216WFC V30 NC, TECHNYL ® SAFE C 216WFC V50 NC, TECHNYL ® SAFE C 216WFC V30 BK & TECHNYL ® SAFE C 216WFC V50 BK'. Natural (appears white) and black coloured, injection moulded, filled Polyamide 6 materials. For use with water up to 85°C.
RADILON® AESTUS T1 RV400RKC 106 NT. RADILON® AESTUS T1 RV500RKC 106 NT. RADILON® AESTUS T1 RV400RKC 306 BK. RADILON® AESTUS T1 RV500RKC 306 BK. Natural (appears brown/yellow) and black coloured, injection moulded glass fibre filled Polyamide 6T/6I materials. For use with water up to 85°C.
'Vydyne A30 GF Natural WR'. Natural (light grey coloured), injection moulded PA66 material. For use with water up to 85°C.
'PLUSTEK PB305G33BK43'. Black coloured, injection moulded PA6 material. For use with water up to 23°C.
‘Tecotek OP20 BK014 01 0A QF, Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF’. Tecotek OP20 BK014 01 0A QF is a black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C. Tecotek OP20 GR30 BK014 01 0A QF, Tecotek OP20 GR10 BK014 01 0A QF & Tecotek OP20 GR20 BK014 01 0A QF are black coloured, injection moulded, filled PPO/HIPS materials suitable for use with water up to 85°C.
‘4TECH 9S20000 W-A-ABK 01 0A QF, 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK’. Black coloured, injection moulded PPO & PPO/HIPS materials. 4TECH 9S20000 W-A-ABK 01 0A QF is an unfilled PPO material suitable for use with water up to 23°C. 4TECH 9S22130 W-A-ABK, 4TECH 9S22110 W-A-ABK & 4TECH 9S22120 W-A-ABK are filled PPO/HIPS materials suitable for use with water up to 85°C.
'NORYL FE1410PW – 73701, NORYL FE1520PW – 73701, NORYL FE1630PW – 73701 & NORYL FE1740PW – 73701'. Black coloured, injection moulded PPE + PS materials. For use with water up to 85°C.
'NORYL WM330G-73701'. Black coloured, injection moulded PPE + PS material. For use with water up to 85°C.
'RAMTON PPS300PWG8NT'. Brown coloured, extruded PPS material. For use with water up to 85°C.
'5308400500 polypropylene liner tube', taupe coloured, injection moulded polypropylene liner. In March 2025, '5308400500 polypropylene liner tube', natural (appears beige), injection moulded polypropylene liner was added to the approval. For use with water up to 23°C.
‘RAMLLOY PNS300PWG6BK10’. Clear, extruded polystyrene polyphenylene material. For use with water up to 85°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
'SYC3 0825 S30CB04 Boot'. Black coloured, compression moulded silicone rubber boot component. Shore hardness 30. The component has an irregular shape with a tested in-radius size of between 0.6mm & 1.2mm. For use with water up to 85°C.
Range of side or bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Double check valve assembly consisting of two spring loaded resilient trim check valve cartridges housed in a nickel plated DZR brass body. The product also incorporates a lever operated isolation valve. For use with copper tube to BS EN 1057. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed), over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The products incorporate a pull-out spout with a plastic aerator. Both models incorporate an approved check valve cartridge within the quick connector to the pull-out hose, and the inlet to the pull-out spout of the 63036-01X model incorporates an approved check valve cartridge with a plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assembies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridges and quarter turn ceramic discs headworks with single lever or dome type operating members. The spout outlets are either open outlet, waterfall or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), with non-rising spindle headwork and single lever operating members.The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge, non-rising spindle or quarter turn ceramic disc headwork with either a single lever, cross top or dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. Some models incorporate open outlet or waterfall spouts. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar. Maximum operating temperature - 60 °C.
Range of two hole, single outlet (fixed), deck mounted combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members (T7401 has cross top operating member) and a manual diverter to the shower outlet. The spout outlet incorporates an aerator or are open outlet and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed), deck mounted combination tap assembly (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and manual diverter to the shower outlet. The waterfall spout outlet incorporates a stainless-steel aerator, and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies). Incorporating a thermostatic cartridge controlling the temperature with dome operating members that incorporate a manual override button, and a quarter turn ceramic disc headworks controlling the flow with dome type operating members. The spout incorporates a lockable diverter to shower outlet and a plastic flow straightener. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8 Bar Maximum operating temperature 60°C
Two hole, double outlet (swivel) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. The tap is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, three-hole single outlet (fixed) bath and shower mixers with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with cross top or single lever operating members (see model) and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted concealed four-hole, single outlet (fixed) combination tap assemblies (brass body with chrome plated or matt black finish trim set), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout inlet has a compression connection for use with copper pipe (manufactured to EN 1057) and incorporates a plastic aerator on the outlet. The product is supplied with a wall mounted shower outlet elbow with integral handset holder, shower hose and a shower handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted spout outlet with chromium plated brass body, incorporating a plastic flow regulator in the inlet. Open outlet use. Maximum operating temperature: 60°C.
Deck mounted spout outlet with chromium plated brass body. The inlet incorporates a plastic flow regulator, and the spout outlet incorporates a plastic flow straightener with an integral strainer. Maximum working pressure: Open Outlet. Maximum operating temperature 60.0°C.
Range of deck mounted spout outlets (brass bodies - various finishes). Supplied with metal backnuts. Open outlet use only Maximum operating temperature: 60°C
Range of Fusion One and Fusion Pro chemical dosing systems. The Fusion One models are housed in a single cabinet capable of delivering one product but can be linked together to create multiple configurations. The Fusion Pro models are housed in a different cabinet capable delivering multiple products via a select valve. Maximum working pressure 6.5 bar. Maximum operating temperature 50°C.
Press (TH press profile) and screw/compression fittings with brass bodies for use with Comisa Evo Pipe (PE-RT/AL/PE), for above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of AIS tin-plated brass and PPSU press fit fittings for use with MULTIPIPE multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of MULTITUBO tin-plated brass and PPSU press fit fittings for use with MULTITUBO multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of ‘NiroSan’ stainless-steel crimped fittings incorporating EPDM ‘O’ Rings, for use with ‘NiroSan’, ‘NiroSan SF’ & ‘NiroSan -ECO’ stainless-steel pipe (all manufactured to EN10312). The fittings and pipe are assembled using a crimping tool with either ‘M’ (15-108mm), ‘V’ (15-54mm) or ‘SA’ (15-108mm) crimping profiles. For above ground use only. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.
‘Hansen easy fit’ range of polypropylene compression fittings with EPDM ‘O’-rings for use with metric PE80 (20mm-63mm) and PE100 (32mm-110mm) pipe to AS/NZS:4130 and plastic pipe inserts. For above and below ground use. Maximum working pressure: See models. Maximum operating temperature: Cold water use only.
Range of M profile brass press fittings with EPDM ‘O’-rings or gaskets to be used with copper pipe manufactured to EN1057 for above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘Isiflo Sprint’ push fit fittings for use with PE100 pipe (manufactured in accordance with EN 12201), for above and below ground use. Isiflo Sprint Family fittings can be installed with seal liners, support liners and without any liner. Maximum working pressure 16 bar. Cold water use only.
Allpex range of end feed capillary fittings and brazing fittings for use with copper tube (manufactured to BS EN 1057). EG fittings have gunmetal bodies, ED fittings have DZR brass bodies & EB fittings have brass bodies. For above ground use only. Maximum working pressure: 6mm – 34mm 25Bar, 34mm -54mm 25Bar, 54mm – 108mm 16Bar, 108mm – 159mm 5 Bar. Maximum operating temperature 30°C
Range of copper end feed solder fittings for use with copper tube (EN1057). For above and below ground use. Maximum working pressure for sizes 8mm to 54mm is 25.0 bar. Maximum working pressure for sizes above 54mm is 16.0 bar. Maximum operating temperature 99°C.
Range of dual flush WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of direct gas fired condensing storage water heaters with an enamel lining and a titanium anode. Fitted with a temperature and pressure relief valve set at 10.0 bar & 95°C. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of indirect water heaters with an enamel lining, a magnesium sacrificial anode and single wall spiral heat exchanger (maximum working pressure 6.0 bar). Fitted with a temperature and pressure relief valve set at 10.0 bar & 95°C. Maximum working pressure 7.0 bar. Maximum operating temperature 80°C
Range of stainless steel lined direct water heaters fitted with a temperature and pressure relief valve set at 10.0 bar & 95°C. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of stainless steel lined direct water heaters fitted with a temperature and pressure relief valve set at 10.0 bar & 95°C. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of indirect water heaters with an enamel lining, a magnesium sacrificial anode and single wall spiral heat exchanger (maximum working pressure 6.0 bar). Fitted with a temperature and pressure relief valve set at 10.0 bar & 95°C. Maximum working pressure 7.0 bar. Maximum operating temperature 80°C
Range of wall mounted combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system. The primary circuit incorporates a pressure relief valve set at 3.0 bar and an expansion vessel. The products are supplied with isolation valve on both the DHW and CH circuits. The secondary circuit (DHW) incorporates a plastic flow restrictor and stainless-steel strainer. Some models (see model section) are supplied with a filling loop assembly consisting of an in-line isolation valve, an in-line double check valve assembly which incorporates an isolation valve. Maximum working pressures: DHW: 10.0 Bar CH: 2.5 Bar Maximum operating temperature: DHW: 65.0°C CH: 85.0°C
Range of wall mounted combination boilers providing domestic hot water (DHW) via a plate heat exchanger and pressurised central heating (CH) system. Incorporating a pressure relief valve set at 3.0 bar and expansion vessel. Supplied with a filling loop assembly consisting of an in-line isolation valve, an in-line double check valve assembly which incorporates an isolation valve. Maximum working pressure Primary circuit (CH) 2.5Bar, Secondary circuit (DHW) 10.0 Bar Maximum operating temperature 90.0°C
Range of in-line and concentric water meters with composite bodies, TPE gasket and NBR ‘O’-ring(s). The products have an integral plastic filter. The inlet of the in-line models includes a non-return valve. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with brass bodies, plastic turbines and plastic strainers on inlets. The products have an integral plastic filter. The inlet includes a non-return valve. Maximum working pressure 16.0 Bar Maximum operating temperature 23.0°C
‘Helvatron H2O’ range of ultrasonic water meters with brass bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of in-line ultrasonic water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters (blue epoxy coated, cast iron bodies). Maximum working pressure 20 Bar. Maximum operating temperature 30°C
Spray handset for personal hygiene (brass bodied - various finishes) incorporating a trigger mechanism controlling the flow. The handset also has a locking ring. The inlet incorporates an approved check valve cartridge with an integral plastic flow regulator; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of horizontal or vertical multi-stage pumps with a stainless-steel body (HM models) or cast iron body with blue coloured cationic resin coating (VM models), incorporating either plastic or stainless-steel impellers (see model), stainless steel sleeve, EPDM gaskets and seals. Maximum working pressure 10.0 bar / 16.0 bar (see models). Cold water use only.
Range of shower outlets, (brass bodies - various finishes), incorporating ball joints, EPDM ‘O’-rings and NBR rubber seals. Maximum operating temperature 60°C
Range of wall or ceiling mounted shower outlets with plastic bodies (various finishes) and brass shower arms (various finishes, incorporating EPDM O-rings and plastic flow regulators. Maximum operating temperature 60°C.
Wall outlet with a stainless steel body incorporating a shower handset holder. Maximum operating temperature 65°C.
Range of wall mounted shower arms with brass bodies (various finishes - see models). Maximum working temperature 70°C.
Range of electronic pressure switches housed in a plastic body with a ceramic sensor and NBR gaskets and/or ‘O’-rings. The 1091203260 & G0912026 models incorporate a spring-loaded plastic flow restrictor. Maximum working pressure 12.0 bar. Cold water only.
Range of pillar taps (chrome plated brass bodies), incorporating either a non-rising spindle headworks (T6308 & T6307M only) or quarter turn ceramic disc headworks (all other models) with single lever, dome type or cross top type operating members (see models). The products are supplied with metal back nuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure; 10 Bar Maximum operating temperature 60°C
Range of wall mounted, fixed, self-closing basin pillar taps (chromium plated brass), incorporating a spring-loaded headwork controlling the flow with either dome type or lever operated operating members (see models). The outlets incorporate plastic flow straighteners. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of stainless-steel braided EPDM lined flexible hoses, incorporating EPDM gaskets. Some models incorporate an isolation valve. Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of stainless-steel or nylon braided PEX lined hoses, incorporating EPDM O-ring or gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of Indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 90˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check cartridge, verified by test (suitable for backflow protection against fluid category 2) an expansion vessel and tundish. Maximum working pressure: Secondary: 4.0 Bar Primary: 3.0 Maximum operating temperature 99.0°C
Range of wall mounted, concealed, manually operated blending valves (brass bodies) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure: 10 Bar. Maximum operating temperature: 65°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. Gearbox and handwheel Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring-loaded non-return valves with epoxy coated, cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C
Range of non return valves with bronze bodies and discs, and an EPDM washer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
W-M115 Series of pilot operated pressure differential control valves with adjustable pressure reducing facility. The main valve has a blue epoxy coated ductile iron body. Models are fitted with auxiliary components, including a pressure gauge, brass bodied flow control valve (DN32-DN80 & DN250-DN300), brass ball valves (DN100 – DN300), brass needle valve (DN100 –DN200) and brass bodied strainer (DN100 – DN300). Maximum working pressure 16.0 Bar. Outlet pressure setting is adjustable between the range of 0.6 bar - 8.6 bar. Maximum operating temperature 80°C.
Range of spherical valves with DZR brass bodies and chromium plated balls. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range of in-line lever operated spherical valves with stainless steel bodies, stainless steel ball and PTFE seats. Maximum working pressure 30 Bar. Maximum operating temperature 85 °C.
Range of spherical valves incorporating nickel plated (brass bodies with chrome plated brass ball and operated via lever, handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of screw down stop valves with brass bodies, incorporating EPDM gaskets. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of angled valves with brass bodies (some models chrome plated). Maximum working pressure 10 bar. Maximum operating temperature 65°C
'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DESCAFLEX PWH-300 601701, 601568 & 601700'. Range of black coloured, extruded polyethylene cables consisting of an outer sheath (available in two different thicknesses) and three or four inner cables. For use with water up to 85°C.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
RIAMAXX HT 325 GF20 natur N88FWC. RIAMAXX HT 325 GF25 natur N88FWC. RIAMAXX HT 325 GF30 natur N88FWC. RIAMAXX HT 325 GF35 natur N88FWC. RIAMAXX HT 325 GF40 natur N88FWC. RIAMAXX HT 325 GF45 natur N88FWC. RIAMAXX HT 325 GF50 natur N88FWC. RIAMAXX HT 325 GF20 schwarz R88FWC. RIAMAXX HT 325 GF25 schwarz R88FWC. RIAMAXX HT 325 GF30 schwarz R88FWC. RIAMAXX HT 325 GF35 schwarz R88FWC. RIAMAXX HT 325 GF40 schwarz R88FWC. RIAMAXX HT 325 GF45 schwarz R88FWC. RIAMAXX HT 325 GF50 schwarz R88FWC. Natural (appears beige/brown) and black coloured, injection moulded, glass filled polyamide materials. For use with water up to 85°C.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
'Paryls PPA A6200GLXX' (XX denotes the weight percentage of glass fibre between 30% to 50%). Black coloured, glass fibre reinforced polyamide materials manufactured by twin screw extrusion. For use with water up to 85°C.
'Typlex 3050'. Natural (appears white coloured), extruded PB-1 material. For use with water up to 85°C.
'Ultradur® B4300 G6 FC Aqua Uncolored'. Uncoloured (appears cream), injection moulded PBT material. For use with water up to 85°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ketaspire KT-820 GF30 BG20'. Brown coloured, injection moulded PEEK material. For use with water up to 85°C.
'Ultrason® P 3010 Blau 80100'. Blue coloured, injection moulded PPSU material. For use with water up to 85°C.
'LATENE AG7H G/30 BLACK F:3352'. Black coloured, injection moulded PP material. For use with water up to 23°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'LSR 8220, LSR 8230, LSR 8240, LSR 8250, LSR 8260 & LSR 8270'. Natural (clear coloured), compression moulded liquid silicone rubber materials. Shore hardness between 20 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘WEICONLOCK AN 305-77’. Yellow coloured anaerobic adhesive paste. This product is to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
‘Wall mounted, electronically operated tap assemblies (brass bodies - in various finishes). The flow is controlled by a solenoid valve that is actuated via an infra-red sensor on the spout. The spout outlet incorporates plastic aerators. Maximum working pressure 6 bar. Maximum operating temperature 65°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headworks with single lever operating members. The product incorporates a pull-down hose incorporating plastic aerators and a trigger mechanism. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW104101110xx, TVW103004000xx, TVW125001000xx) are supplied with lever operated pop-up wastes (not verified by test). Models (TVW103005000xx, TVW104105110xx & TVW125002000xx) are supplied with click type pop-up wastes (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW105002000xx, TVW105003000xx, TVW105101110xx & TVW105141110xx) are supplied with lever operated pop-up wastes (not verified by test) Model TVW105105110xx) is supplied with a click type pop-up waste (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators, flow straighteners, stainless steel strainers or open outlet type spouts (see models). Some models are supplied with a click type pop-up wastes, that have been verified by test (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet. Supplied with click waste outlet – verified by test. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic flow straightener (model 63054) or open outlet type spouts (model 63055). The product is supplied with a shower hose and handset Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
Range of wall mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever or dome type operating members. The spout outlets incorporate plastic aerators. These assemblies have two points of swivel. Maximum working pressure: 10 Bar. Maximum operating temperature: Cold water use only.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and cross top operating members. Products are supplied with lever type pop up wastes. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of wall mounted or floor standing spout outlets (fixed or swivel - see model in various finishes). All models incorporate a plastic flow straightener, except for the 93-Floor Mounted Bath Filler which has a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted spout outlets (fixed or swivel - see model, Various finishes) incorporating a plastic flow straightener. The products are supplied with metal backnuts.
Non-metallic materials and components comply with BS6920 at 60°C
Range of stainless-steel expansion bellows with either threaded or flanged end connections. Maximum working pressure JP115: 10.0 bar & JP116VS: 16.0 bar. Maximum operating temperature JP115: 82oC & JP116VS: 100°C.
Range of expansion vessels with butyl membranes. Maximum working pressure 8.0, 10.0, 16.0 or 20.0 bar (please refer to model). Maximum operating temperature 70 or 100°C (please refer to model).
‘BORPLUS’ range of PP-RCT Socket Fusion fittings used with ‘BORPLUS PP-RCT FASER COMPOSITE STABIL’ pipe. Maximum working pressures at 16.0 Bar @ 23°C and 6.0 Bar @ 85°C.
Range of Stainless-Steel pipes and fittings. Models OT 100 are manufactured to EN 10217-7, all other models are manufactured to EN 10253-4. Fittings and pipe are connected via welding. Maximum working pressure; OT 100 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 110 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 200 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 201 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 212 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 213 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 214 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 400 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 401 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 410 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar OT 411 DN15 - DN 200 25 Bar, DN200 – DN350 16 Bar Type 37 DN15 – DN125 16 Bar, DN150 10 Bar Type 37M DN15 – DN80 16 Bar, DN100 10 Bar Maximum operating temperature – 99°C.
Range of fohn stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with FOHN stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of plastic compression fittings incorporating polypropylene bodies& plastic pipe liners.. For use with both PE80 & PE100 pipe manufactured to BS EN 12201. Maximum working pressure 16 Bar Maximum operating temperature 23°C
SANHA Press Series 6000 & 16000 and PURAPRESS Series 8000 of press-fit fittings with copper (6000), bronze (8000) and chrome plated copper (16000) bodies and EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of press fittings with a stainless steel body and EPDM ‘O’ rings for use with stainless steel 316L pipe manufactured to EN10312. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Tectite 316’ range of push-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with stainless steel tube (Grade 316 manufactured to EN 10312). Maximum working pressure: Fittings 15mm to 28mm 10.0 bar. Fittings 35mm to 54mm 6.0 bar. Maximum operating temperature 90°C.
Range of compression fitting with brass and DZR brass bodies, supplied with brass compression rings. For use with copper tube (manufactured to BS EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘B’ Press XL copper crimped fittings with EPDM ‘O’-rings for use with copper pipe to BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper end feed fittings for use with copper tube. For above and below ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of float switches with plastic bodies. Cold water use only.
‘POD’ range of indirect and direct heat interface units providing space heating and instantaneous hot water. The heat transfer is generated via plate heat exchangers. The domestic hot water (DHW) circuit incorporates an adjustable temperature mixing valve. The indirect models incorporate an expansion vessel (on the CW inlet of the DHW circuit) and a pressure relief valve set at 3.0 bar (on the space heating circuit). The indirect models only are supplied with a temporary filling loop, which comprises of a stainless steel braided EPDM lined flexible hose assembly and a lever operated spherical valve for connection to the primary circuit. The angled cold water inlet incorporates an isolation valve and a branch to connect to the filling loop, which includes a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3). Maximum working pressure for indirect units: Primary circuit: 16.0 bar. Space heating: 2.5 bar. Secondary circuit (DHW): 10.0 bar. Maximum working pressure for direct units: Primary circuit: 10.0 bar. Space heating: 10.0 bar. Secondary circuit (DHW): 10.0 bar. Maximum operating temperature for domestic hot water 65°C. Maximum operating temperature for central heating and primary circuit 85°C.
Range of wall mounted gas fired condensing instantaneous water heaters. Maximum working pressure 10.0bar. Maximum operating temperature 85°C.
Octave range of water meters with blue epoxy coated cast iron or plastic bodies (see models). Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C
Range of in-line water meters with either a brass or plastic composite body. The product incorporates a plastic strainer on the inlet. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of single or twin booster pumps with stainless steel bodies and stainless-steel impellers. Maximum working pressure 8.0 Bar Maximum operating temperature 90.0°C
Range of shower handsets and overhead showers, (ABS plastic bodies – various finishes) incorporating plastic flow regulators at the inlets. Maximum operating temperature 60°C. Open outlet use only.
Wall mounted shower outlet comprising of a shower arm (brass body – various finishes) and an overhead shower (stainless steel body – various finishes) incorporating a stainless steel filter washer at the inlet. Maximum operating temperature: 85°C
Range of shower handsets and overhead showers with (plastic or chrome plated plastic bodies). Open Outlet use only Maximum operating temperature 75.0°C
Range of shower kits comprising of ABS bodied shower handsets and PVC multi-layer hoses incorporating EPDM ‘O’-rings. Supplied with riser rail. Available in various finishes. Maximum operating temperature 60°C
Shower handset with a chrome plated ABS plastic body. Maximum operating temperature 85°C.
Overhead ceiling or wall mounted (depending on shower arm) shower outlet with chrome plated plastic body, EPDM o-rings and a plastic flow restrictor at the ball joint. Maximum working pressure: Open outlet. Maximum operating temperature: 60°C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided hoses with EPDM liner and NBR or fibre gaskets. DN13 and DN19 Maximum working pressure 10 bar. Maximum operating temperature 65°C. DN25 Maximum working pressure 10 bar. Cold water use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. SCFA models incorporate a spherical valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Stainless steel interlocked (chrome plated) silicone lined kitchen tap pull-out hose. Open outlet use only. Maximum operating temperature 85°C.
Range of primary hot water buffer tanks consisting of stainless steel shells. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Ultraflow ranges of Direct, Indirect, Solar Single, Solar Twin, Slim Direct and Slim Indirect stainless steel insulated unvented hot water storage cylinders with external expansion. The DHW circuit consists of a temperature and pressure relief valve set at 7.0 bar and 90°C, an inlet control group consisting of a pressure reducing valve adjustable between 2.7 and 3.3 bar, an expansion relief valve (SRV) set at 6.0 bar, a strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) also supplied with a tundish. Maximum supply pressure to the inlet control group 10.0 bar. Maximum working pressures - Primary circuit 6.0 bar, Secondary circuit 5.5 bar. Maximum operating temperature 65˚C.
Range of Ultraflow Air bubble top indirect and direct single coil unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 10.0 bar@90˚C. A safety kit (manifold) consisting of a single check valve assembly, verified by test (suitable for backflow prevention against fluid category 2), strainer, an expansion relief valve set at 8.0 bar and a pressure reducing valve set at 3.0 bar and a tundish is also provided. Alternative inlet control group and temperature and pressure relief valve added January 2023. Maximum working pressure: Secondary circuit: 7.5 bar. Primary circuit: 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of air release valves with plastic bodies, EPDM ‘O’ rings and polypropylene floats. Maximum working pressure 16.0 bar. Cold water use only.
Range of automatic air venting valves with plastic bodies and EPDM ‘O’-rings. Maximum working pressure 6.0 bar. Maximum operating temperature 99°C.
Range of wall mounted, thermostatic shower valves (chromium plated brass) incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with an isolation valve for each inlet. Maximum working pressure; 10 Bar Maximum operating temperature 85°C
Range of wall mounted thermostatic bar shower mixers with brass bodies, incorporating a thermostatic cartridge controlling the temperature and non-rising spindle headwork controlling the flow. The inlets incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Series of wall mounted, thermostatic mixer valve with brass bodies, diverter headwork that controls flow between one, two or three outlets (see model) with various type of operating member. The temperature is controlled independently via a thermostatic cartridge operating member with a manual override button. Inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 55°C
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a single sequential headwork with a single lever operating member. The inlets incorporate a concentric isolation valve, plastic flow regulator & stainless-steel strainer. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.
Range of butterfly valves with ductile iron bodies (blue epoxy coating), stainless steel disc and EPDM seat. The valves are operated by a lever mechanism. Maximum working pressure 20.0 bar. Cold water use only.
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel (2302/2502 models) or chrome plated iron disc 2304/2504 models). Products are either handwheel (H) or gear (G) operated (see models). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of plastic, ceramic disc diverter valves. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ‘901’ float operated equilibrium inlet valves incorporating brass bodies and float arms. Maximum working pressure - See Models Maximum operating temperature – Cold water use only.
Range of pilot operated flow control valves with blue epoxy coated, ductile iron bodies and EPDM ‘O’-rings. Auxiliary components include stainless steel tube with fittings, a stainless-steel strainer and spherical valves. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C or cold water use only – see data plate marking.
Range of globe type spring loaded, resilient trim, non-return valves with epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of globe type spring loaded, resilient trim, non-return valves with epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Some models incorporate a pressure gauge. Valves are pre-set at 3.0, 4.5, 6.0 & 8.0 Bar (all models available for all relief pressures). Maximum operating temperature 99°C.
Range of latching or non-latching normally closed solenoid valves with brass bodies. Maximum working pressure 10.0 Bar to 15.0 Bar (see models). Maximum operating temperature 90.0°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10130420) Maximum working pressure 25.0 bar (model 10130379) Maximum working pressure 40.0 bar (models 10130277 & 10130345) Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chrome plated balls, PTFE seats and FKM O-rings. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range of lever (1307 and 1333 models) or screwdriver operated (all other models) spherical ball valves with brass bodies and a chromium plated brass ball. Max working pressure 16.0 bar. Maximum operating temperature 85°C.
Series of brass valves with EPDM o-ring isolation valves with M profile press crimped connections to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with DZR brass bodies with two test ports, incorporating a non-rising spindle headwork. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
'KOCETAL K300, K500 & K700'. Off-white coloured (opaque), injection moulded acetal materials. For use with water up to 85°C.
'BPL High Build QD Bitu Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer’s data sheet ‘427-rev03’ dated 'Feb' 2024'. Cure: flash off for 15 minutes at ambient temperature of 30°C, followed by stoving at 55°C for 10 minutes and then 7 days maturation at ambient temperature of 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's TDS 'ECL/ TDS / ES1212', issue date '2-Feb-14', version '0'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CLEAN TECH PW (BG)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A and B in a volume ratio of 3:1 and apply as per manufacturer's TDS 'CCPL/TDS/R11/CRC/22-23/04/R13/BG/R1', dated '15.09.2022'. Cure for 7 days@30°C. Between August 2024 and January 2025, the coating is approved for use with water up to 23°C. Between February 2025 and August 2029, the coating is approved for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Unitec 300 Green'. Green coloured compressed fibre gasket material manufactured by calendaring. For use with water up to 23°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
Klingersil C-4430 plus. NBR fibre gasket material, manufactured by calendaring, which is red on one side and beige on the other side. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Novus N34 & SF3300'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, maufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'Veradel AG-330 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
FORTRON® natural (appears cream) or black coloured, injection moulded PPS materials. For use with water up to 85°C. Grades manufactured in Celanese Florence, USA: FORTRON® 1140L4 SF3001 NATURAL FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140L4 BLACK SD3002). FORTRON® 1140L6 SD3002 BLACK DW (formerly known as FORTRON® 1140L6 BLACK SD3002). FORTRON® 1140L6 SF3001 NATURAL FORTRON® 4184L6 SF3001 NATURAL FORTRON® 4184L6 SD3002 BLACK DW (formerly known as FORTRON® 4184L6 BLACK SD3002). Grades manufactured in Celanese Nanjing: FORTRON® 1140L4 SF3001 NATURAL DW (formerly known as FORTRON® 1140 L4 SF3001 natur CN). FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140 L4 SD 3002 black).
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
'RBL-9200-20, RBL-9200-30, RBL-9200-40, RBL-9200-50, RBL-9200-60, RBL-9200-65 & RBL-9200-70'. Transparent, colourless injection moulded silicone rubber materials. Shore hardness between 20 & 70. Tested in-radii size between 0.75mm & 2.89mm. For use with water up to 85°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve that is activated via an infrared sensor. The spout outlet incorporates an aerator. Maximum working pressure: 8.0 Bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a lever type operating member. The spout outlet incorporates a metal aerator. The product is supplied with a lever type pop up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Thermostatic cartridge incorporating a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of Single hole, single outlet fixed combination tap assemblies incorporating ceramic disc cartridge headworks with single lever operating members. Models XB-MP-028, XB-MP-030, XB-MP-050, XB-MP-051, and XB-MP-052 incorporate plastic aerators, Models XB-MP-027, XB-MP-029, XB-MP-031 and XB-MP-032 incorporate a plastic flow straightener. Maximum working pressure all models 10.0 bar. Maximum operating temperature 85⁰C for Models XB-MP-018 and XB-MP-035 all other models are 65⁰C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly with brass bodies (various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure: 10Bar. Maximum operating temperature: 60°C.
Floor mounted single hole, single outlet (fixed) combination tap assembly (brass bodies -various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with metal backnuts Maximum working pressure 10.0 Bar. Maximum operating temperature 60 °C
Range of chemical dosing equipment which incorporate self-closing valves within a plastic body. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Maximum working pressure 6.0 bar. Maximum operating temperature 60ºC.
Range of filter cartridges. Maximum working pressure 8.0 Bar. Cold water use only.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (EN1057). Maximum operating pressure - 16 bar @ 30°C and 10 bar @ 95°C.
Range of “JRG Sanipex MT” compression fittings with EPDM ‘O’-rings for use with “JRG Sanipex MT ECO” multilayer pipes (PE-RT II/Al/PE-RT II). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
B Profile range of 316L & 304 stainless steel press fittings with EPDM ‘O’-rings for use with stainless steel pipe manufactured to EN 10312, for both above and underground use. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of R-154 stainless steel pressed collars incorporating stainless steel bodies (304L or 316L) and are only to be used with stainless steel pipe. Maximum working pressure for sizes up to DN150 (FCM models) or DN125 (FCI models) is 25.0 bar. Maximum working pressure for size DN200 (FCM models) or DN150 and DN200 (FCI models) is 16.0 bar. Maximum operating temperature 99°C.
Silicon Bronze bodies Press Fittings with EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Copper press-fit fittings with copper with EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
FLOMASTA range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of stainless steel press fittings: SS316L stainless steel models are for use with SS316L stainless steel pipe manufactured to EN 10312.; SS304 stainless steel models are for use with SS304 stainless steel pipe manufactured to EN 10312. Crimp joint is achieved by a M profile crimp jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of system 2000 of flange adaptors and connectors with ductile iron bodies (Blue Epoxy Coated) incorporating EPDM seals. For use with PE pipe manufactured to En 12201 & PVC Pipe manufactured to DIN 8062. Maximum working pressure: 16.0Bar Cold water use only.
‘PREMIX’ range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both the domestic hot water and primary circuit are controlled via spherical valves. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 80°C.
Range of rotating piston, volumetric in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of IUW ultrasonic water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature: 50°C.
Range of in-line water meters with brass bodies and plastic turbines. The inlets incorporate plastic filters, and the outlets incorporate non-return valves (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 65.0°C.
Range of ‘Thermowatt’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of two, three or four pump booster sets, with vertical multistage pumps comprising of pressure vessels, stainless steel manifolds, pressure gauges, spherical valves and EPDM O-rings. Maximum working pressure - 10.0 bar. Max operating temperature - Cold water use only.
Range of two, three and four pump cold water booster sets. The products incorporate a suction and discharge manifold and pumps. Maximum working pressure 10 bar. Cold water use only.
Range of horizontal multistage close coupled centrifugal pumps incorporating stainless steel cased bodies and impellers. Maximum working pressure: See models. Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
EASO range of shower head and hand showers, with ABS bodies and chromium plated finish. Open outlet use. Maximum operating temperature - 65 °C.
Range of shower outlets comprising of shower heads all incorporating stainless-steel strainer washers (plastic bodies-various finishes) and handheld showers (plastic bodies - various finishes). Maximum operating temperature 75°C.
Range of overhead shower and shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
Range of overhead shower outlets with Various finishes. The inlets incorporate a stainless-steel strainer and flow regulator. Models 64400250CH, 67400250BBL, 63400250BBR, 68400250MB & 61400250BRZ Incorporates a shower arm.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets and overhead showers, (plastic bodies - various finishes). The inlets incorporate a plastic flow restrictor and stainless steel strainer. Maximum operating temperature 60°C. Open outlet use only.
Flow sensor with a plastic and brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of self-closing basin taps (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic aerator, and the products are supplied with metal backnuts. Maximum operating pressure 7 Bar Maximum operating temperature 55 °C
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of stainless steel inter-locked shower hoses incorporating PVC linings in various finishes. Maximum operating temperature 65°C.
Range of elastomeric shower hoses with EPDM lining and ‘O’-rings. The product incorporates a flow restrictor. Maximum operating temperature 60.0°C Open outlet use only
Range of stainless steel braided, EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless steel interlocked shower hoses with EPDM O-rings. Maximum operating temperature 65°C. Open outlet use only.
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection). Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of Compress 5800i AW vertical cased and insulated indirect unvented stainless steel hot water storage cylinders fitted with a Caleffi 309508 CST temperature and pressure relief valve set at 10 bar & 90°C, and supplied with a Caleffi inlet control group consisting of in-line pressure reducing valve (set at 3.5 bar) and pressure relief valve (set at 6 bar) and incorporates an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2). The cyclinders also supplied with an 18L expansion vessel and Intatec filling loop assembley (FL12041510). Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Range of wall mounted, manually blended, shower valves, (brass bodies – various finishes). Incorporating a ceramic cartridge controlling both the flow and temperature. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, manually operated blending valves (brass bodies - various finishes) incorporating a ceramic cartridge headwork controlling both flow and temperature and a self cancelling diverter with a lever type operating member. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted bar type shower mixing valve (brass body, various finishes - see model). The product incorporates a ceramic cartridge headwork with a single lever operating member. The hose outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of concealed, wall mounted thermostatic blending valves with brass bodies (chromium plated trim sets). The products consist of a two-way diverter and a thermostatic cartridge controlling the temperature. All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of thermostatic, concealed, 2 and 3 outlet shower valves with (brass bodies - various finishes) incorporating a thermostatic cartridge controlling the temperature and diverter cartridge which also controls the flow. The 2 outlet models, the cartridge only controls flow. The products contain an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of concealed wall mounted thermostatic shower valves, (brass bodies – various finishes & strim sets). Incorporating either a ceramic disc headwork, two-way diverter or both (see models). The temperature is controlled independently via a thermostatic cartridge. The valves incorporate approved single check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 44.0°C
Range of wall mounted concealed thermostatic blending valves with (brass bodies – various finishes), incorporating single lever or cross top operating members. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of concealed thermostatic shower mixers (brass bodies - various finishes). The flow is controlled by a four-way manual diverter (3 on, 1 off positions) with single lever, cube type or dome type operating members. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with single lever, cube type, dome type or cross top operating members. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic blending shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc two-way diverter headwork controlling the flow with dome or square type operating members. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with dome or square type operating members. The inlets incorporate a stainless-steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of wall mounted concealed electronically controlled thermostatic shower mixers, incorporating plastic solenoid valves to control the flow to various outlets activated via a remote actuator. The temperature is controlled via two transducers housed within the concealed box. The products incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure: 6.0 bar. Maximum operating temperature: 65°C
Range of two-way manual diverter valves with shut-off position. Products are for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of regulating and shut-off valves with brass bodies and EPDM ‘O’-Rings. Maximum working pressure 16.0 Bar for BSP (M) and 25.0 bar for BSP (F). Maximum operating temperature 85.0°C
Range of swing gate, non-return valves with (blue or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of lever operated spherical valves with nickel plated brass bodies, chromium plated brass ball, PTFE seats and a drain valve. Maximum working pressure 25.0 Bar Maximum operating temperature 100.0°C
Range of spherical valves with a brass body and PTFE seats. The products incorporate a lever or butterfly type handles. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range square operated (see models) spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of resilient seated gate valves with a blue epoxy coated ductile iron body and a ductile iron gate/wedge which is fully encapsulated with EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 166 30 SERIES model has a rising spindle, the 166 33 SERIES model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated) with EPDM coated ductile iron wedge and non-rising stem operated via a hand wheel operating member. Maximum working pressure: 16 bar. Maximum operating temperature: 80°C
Range of cold-water inlet control groups consisting of an in-line, manually adjustable pressure reducing valve and a pressure relief valve pre-set at either 6.0 or 8.0 bar, housed within DZR brass bodies. The products incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. The pressure reducing valves also have stainless-steel strainers. Maximum inlet pressure 16.0 bar. Cold water use only. CWIC351300 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 6.0 bar CWIC351301 – Outlet pressure range 1.0 to 2.1 bar. Pressure relief valve set at 8.0 bar. CWIC351303 – Outlet pressure range 1.0 to 3.5 bar. Pressure relief valve set at 8.0 bar CWIC351306 – Outlet pressure range 1.5 to 6.0 bar. Pressure relief valve set at 8.0 bar
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 16.0 bar. Cold water use only.
'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EDELPOXY FNSL 151'. Factory applied, two-component, grey coloured epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's instructions for use, reference number 'PC 151', dated January 16, 2015. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSAW-JAL (OPC-JKL)'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘DENYL 6 5010 NERO 0300, DENYL 6 3010 NERO 0300, DENYL 6 1510 NERO 0300, DENYL 6 5010 NERO, DENYL 6 3010 NERO & DENYL 6 1510 NERO’. Black coloured, injection moulded, glass fibre filled PA6 materials. For use with water up to 85°C.
'Grilon TSG-30/4 FA Black 9840'. Black coloured, injection moulded PA material. For use with water up to 85°C.
Grilamid LBV-30H FWA natural & black 9225. Grilamid LBV-50H FWA natural & black 9225. Grilamid LBV-65H FWA natural & black 9225. Glass filled (30%, 50% & 65%), injection moulded nylon material available in natural and black colours. For use with water up to 85°C.
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-out spray outlet incorporating a plastic aerator. The spray outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway 98°C, for mixed water pathway 65C and purified water pathway 85°C
Non-verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Ceramic cartridge headworks with a plastic body, incorporating silicone seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure - 10 Bar Maximum operating temperature - 85 °C
Range of single hole, single outlet (swivel) pullout spray combination tap assembly (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Model WJ IX008A has a stainless-steel body. Incorporating a ceramic cartridge headworks with single lever operating members. Models WJ 6181000XX & WJ 6181700XX have dome type operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Deck mounted, single hole, single outlet fixed combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Deck mounted, single hole, single outlet fixed combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied mounting kit that comprises of stainless-steel braided hoses and isolation valves that incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass). The T6305M model incorporates non-rising spindle headworks with dome type operating members. The T6505 model incorporates ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The aerator includes an integral stainless-steel strainer. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
‘Arco,’ ‘Zero,’ ‘Slim’ & ‘Trenta9’ ranges of wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork and either a single lever operating member (Trenta9 models) or dome type operating member (all other models). The spout connection of the Arco models incorporates a plastic flow regulator. The spout outlet of all other models incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Model (TVW125003000xx) is supplied with a click type waste (verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) with a manually operated diverter to shower outlet. The T6301M model incorporate non-rising spindle headworks with dome type operating members. The T6501 model incorporates quarter turn ceramic disc headworks with single lever operating members. The spouts incorporate a plastic aerator with an integral stainless-steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided TPSiV lined hose assemblies Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of combined bath filler and/or waste and overflow assemblies (see models) in various finishes. Open outlet use only Maximum operating temperature: 60ºC
Range of wall mounted spout outlets (brass bodies - various finishes). Maximum operating temperature 60°C Open outlet use only.
Range of cylindrical expansion vessels with epoxy coated or uncoated steel bodies and Butyl membranes. Maximum working pressure 10.0 Bar (15.0 bar INOX PRO 0.16L). Maximum operating temperature 99.0°C.
Range of expansion vessels with fibreglass bodies and butyl diaphragms. Maximum working pressure: 8.6 Bar. Maximum operating temperature: 23 °C.
Range of “JRG Sanipex MT” compression fittings for use with “JRG Sanipex MT” multilayer pipes (PE-Xc/Al/PE-Xb 16x2,25mm to 40x3,5mm and PE-Xc/Al/PE-Xc 50x4,0mm and 63x4,5mm). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C for dimensions 16x2,25 mm to 40x3,5 mm. Maximum operating temperature 60°C for dimensions 50x4,0 mm and 63x4,5 mm.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “SOUTH PRESS” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
A range of black polyethylene electrofusion fittings from DN 20 to DN 1200 for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. A range of black polyethylene butt-welded fittings from DE 20 to DE 1200 fittings for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. Maximum working pressure: 20.0 bar for SDR 9 Maximum working pressure: 16.0 bar for SDR 11 Maximum working pressure: 10.0 bar for SDR 17. For above and below ground and cold water use only.
‘Safety’ range of PPS compression fittings for use with “Multi-Calor” multi-layered PEX/Al/PEX pipe. For above ground use only. Maximum working pressure 10bar. Maximum operating temperature 95 °C.
‘Pexalbrass’ range of brass press fittings for use with “PEXAL” multi-layered (PE-X /Al/PE-X) pipe. Joints are achieved via crimping tool for H (DN16, DN20, DN26, DN32), TH(DN16, DN20, DN26, DN32, DN40, DN50, DN63), U (DN16, DN20, DN26, DN32, DN40, DN50, DN63, DN75, DN90, DN110) profile. Maximum working pressure 10bar. Maximum operating temperature 95 °C.
‘FRABOPRESS BIG-SIZE’ range of copper and bronze press fittings for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C
‘FRABOPRESS COPPER M’ range of copper and bronze press fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘FRABOPRESS 316 M’ range of stainless-steel press fittings for use with stainless steel pipe (manufactured to EN 10312:2002 & EN 10217:2021). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of brass threaded fittings,. Above ground use only. Maximum operating pressure of 16.0 bar. Maximum operating temperature of 85°C.
DMFit range of black, grey and white plastic pushfit fittings for use with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. (White fittings were added to the approval in August 2025). When used with DM LLDPE tubing the supplied black or grey pipe inserts (ATS) must be installed. When used with PEX barrier pipe the supplied beige pipe inserts must be installed. DM LLDPE tubing are available in black, natural (appearance is white), white, red, and blue colours. Maximum working pressures and temperatures: When used with DM LLDPE tubing: 4-15mm & 5/32”-½” pushfit sizes: 12.0 bar, cold water use only. 6-15mm & ¼”-½” pushfit sizes: 7.0 bar @ 65°C. When used with PEX Barrier pipe (manufactured to BS7291-3): 15-22mm pushfit sizes: 12.0 bar, cold water use only and 7.0 bar @ 65°C. Fittings which incorporate 4-10mm & 3/16” - ⅜” barb connections: 12.0 bar, cold water use only. Fittings which incorporate ½” - ¾” barbed end connections are open outlet use only. Maximum operating temperature 65°C.
“<A> Press Copper M Profile” series press fittings with a copper body and EPDM ‘O’-rings, for use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Press-Inox range of stainless-steel crimped fittings (‘M’ crimp profile) for use with stainless steel pipe (manufactured to EN10204). For above ground use only. Maximum working pressure: 16Bar. Maximum operating temperature: 100°C.
Range of brass (CW617 or CW511L) press fit fittings (M-Type) for use with copper pipe manufactured to EN 1057. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.
Range of water meters with epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (AMS models), 4.0 bar (EDH & EMH models) 8.0 bar (LVS models). Maximum operating temperature 85°C
Range of booster sets consisting of two or four electronically controlled pumps, stainless steel manifold, spherical valves, expansion vessels and pressure gauge/transducers and non-return valves. Maximum operating pressure 16 bar. Maximum operating temperature 23°C.
Range shower outlets and accessories with brass bodies (various finishes). The inlet of the overhead shower outlet incorporates a stainless steel strainer. Maximum operating temperature 85°C. Open outlet use only.
Range of overhead shower outlets, (brass bodies – various finishes) incorporating NBR O rings. Maximum operating temperature: 65C
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Range of shower handsets and connection hoses (brass bodies – various finishes). The inlet incorporates an approved check valve cartridge (with plastic flow regulator) however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C
Range of shower handsets and overhead showers with (plastic or chrome plated plastic bodies). Open Outlet use only Maximum operating temperature 75.0°C
Range of overhead showers incorporating ABS (plastic bodies - various finishes), stainless steel strainer and flow restrictor (flow restrictor only on “minus flow” models) in the inlets. Open outlet use only. Maximum operating temperature 60.0°C
Range of flanged `Y` patterned in-line strainers with blue epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of Y-pattern strainers with DZR brass bodies and stainless steel strainers. The compression connection is for use with copper pipe to BS EN1057. Maximum working pressure 20 bar (BSP threaded models ½”-2”), 16.0 bar (compression models). Maximum operating temperature 85°C.
Range of stainless steel braided hoses, incorporating a dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. The SOG1212XXX(GLF)CS model incorporates an isolation valve. The models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel interlocked or PVC reinforced (see models), PVC inner lined flexible hose assemblies (various finishes). Open outlet use only. Maximum operating temperature 65°C.
Braided, double outlet, silicone hose assembly with stainless steel connectors. Maximum operating temperature 98°C. Open outlet use only.
Range of nylon braided PEX lined flexible hose assemblies with EPDM washers and ‘O’-rings with a variety of end connections. Maximum operating temperature 65.0°C
Range of shower hoses, with either a interlocked stainless steel outer hose (PVC or PEX inner hose - YHR01-A-A-**-**-**& YHR02-A-A-**-**-**); or a PVC outer hose (YHR03-A-A-**-**). Open outlet use only. Maximum operating temperature 65°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of 2, 3, 4 and 5 port manifold assemblies with brass bodies (various finishes) for use with copper pipe (BS EN 1057) and “EA” range of PEX/AL/PEX multilayer pipe. Some models have non rising spindle headworks control valve in the ports. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 95.0°C.
Range of 2, 3, 4 and 5 port manifold assemblies with brass bodies (various finishes) for use with copper pipe (BS EN 1057) and South Press range of PEX/AL/PEX multilayer pipe. Some models have non rising spindle headworks control valve in the ports. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 95.0°C.
Range of wall mounted, manually operated blending valves (brass bodies, chromium plated) incorporating a ceramic cartridge headwork with a single lever operating member. Outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 bar. Maximum operating pressure: 60oC.
Wall mounted, manually operated blending valve (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. Outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 5.0 bar. Maximum operating pressure: 60oC.
T-type thermostatic mixing valves with a brushed chrome DZR brass body. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. The valves are either handwheel and gear operated (Models D371X and DL371X) or lever operated (Models D71X and DL71X). Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Range of lugged, semi lugged, wafer type or U shaped (see models) butterfly valves with a blue epoxy coated cast iron body, EPDM seat and either a stainless steel, bronze, EUROKOTE - EBONITE or blue epoxy coated iron disc (see models). Maximum working pressure 6.0, 10.0 or 25.0 Bar (See models) Maximum operating temperature 23.0 or 60.0°C (See models)
Range of in-line, adjustable, pressure reducing valves with DZR brass bodies. For use with copper pipe to EN 1057. Maximum inlet pressure 16.0 bar. Outlet pressure adjustable between 1.5 bar & 5.5 bar. Cold water use only.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies. Some models have a pressure connection and can be supplied with the pressure gauge. Model 533041H GBT, 533230H & 533430H has a maximum inlet supply pressure 10.0 bar, an outlet pressure range of 0.8 to 4.0 bar and a maximum operating temperature of 85°C. All other models: Maximum inlet supply pressure 16.0 bar. Outlet pressure range 1.0 to 6 bar. Maximum operating temperature 80°C
Range of lever operated spherical valves with a nickel-plated brass body and a chrome plated brass ball, NBR ‘O’-rings and PTFE seats. Maximum working pressure 30.0 bar. Maximum operating pressure 85°C.
A screwdriver operated spherical ball valve with brass body, chromium plated brass ball and EPDM O-ring. Maximum working pressure 5.5 bar. Maximum operating temperature 85oC.
Range of spherical valves incorporating a chrome plated brass body & brass ball. Maximum operating pressure 10 bar. Maximum operating temperature 65 °C.
Albion SLP series of normally open and normally closed solenoid valves with brass bodies. Maximum working pressures SLP**EE* models 12.0 bar, SLP**EE*H models 8.0 bar. Maximum operating temperature 70°C.
Range of Instantor lever action ball valves with brass bodies, chromium plated brass balls and PTFE seats. Maximum working pressure 25 bar. Maximum operating temperature 85°C
Range of spherical valves with stainless steel bodies, PTFE seats and silicone O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of spherical valves with PVC-U or ABS bodies and ball (see models).. PVC-U models with a solvent weld pipe connection are for use with PVC-U pipe (manufactured to ISO 1452) and are supplied with a PVC-U solvent cement. ABS models with a solvent weld pipe connection are for use with ABS pipe (manufactured to ISO 15493) and are supplied with an ABS solvent cement. Maximum working pressure 16.0 Bar. Cold water use only.
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
'KOCETAL® K100BK & KOCETAL® K300BK'. 'KOCETAL® K500BK’ was added to the approval in June 2025. Black coloured, injection moulded POM materials. For use with water up to 23°C.
‘KOCETAL® WR301 (white coloured) & KOCETAL® WR301 BK (black coloured)’. Injection moulded POM materials. For use with water up to 23°C.
'CELCON F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘CELCON F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch CELCON MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'FORMOCON FM130'. White coloured, injection moulded POM material. For use with water up to 85°C.
'J1200 (RBSIC) & J1300 (SSIC)'. Grey coloured, compression moulded and sintered, Silicon carbide mechanical sealing rings. For use with water up to 85°C.
'H/E16018'. Factory applied, dark blue coloured electrostatic enamel coating. Apply as per manufacturer's TDS '00', dated '30.08.2017' and cure for 4.5 minutes at a peek temperature of 850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOROGUARD 20 RED & GREY'. Factory applied, two-component epoxy coatings available in red and grey. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS dated 'Jan 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DZT PANT I1000-NC; DZT PANT I10G05-NC; DZT PANT I10G10-NC; DZT PANT I10G15-NC; DZT PANT I10G20-NC; DZT PANT I10G25-NC; DZT PANT I10G30-NC; DZT PANT I10G35-NC; DZT PANT I10G40-NC; DZT PANT I10G45-NC; DZT PANT I10G50-NC; DZT PANT I10G55-NC; DZT PANT I10G60-NC; DZT PANT I10G65-NC (un-pigmented - appears beige)’. ‘DZT PANT I10G05-BK; DZT PANT I10G10-BK; DZT PANT I10G15-BK;DZT PANT I10G20-BK;DZT PANT I10G25-BK; DZT PANT I10G30-BK; DZT PANT I10G35-BK;DZT PANT I10G40-BK;DZT PANT I10G45-BK; DZT PANT I10G50-BK; DZT PANT I10G55-BK; DZT PANT I10G60-BK; DZT PANT I10G65-BK (black coloured)'. Injection moulded PA materials. For use with water up to 85°C.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Revolve N-307 (5056) Natural'. Natural (appears white), rotationally moulded PE material. For use with water up to 85°C.
'DIC.PPS Z-230-T5 BLACK'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of CA-b backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of CAb backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Filling link with manual or automatic tap. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Range of wall mounted three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 60°C
‘MUFA’ and ‘MUPA’ ranges of expansion vessels with epoxy coated bodies. ‘MUFA’ models have a maximum working pressure of 8.6 bar. ‘MUPA’ models have a maximum working pressure of 10.0 Bar. Cold water use only.
Range of in-line carbon block water filters and housings with polypropylene bodies. Maximum working pressure 8.0 bar. Cold water use only.
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use (sizes 12mm-54mm only. 66.7mm, 76.1mm, 88.9mm & 108mm for above ground use only) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PCC type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (Unipress MLCP ) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Supreme range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Tectite Classic and Tectite Pro ranges of copper alloy push-fit fittings The Tectite Classic range is for use with copper tube (manufactured to BS EN 1057) and PEX & Polybutylene tube (manufactured to BS 7291). The fittings are supplied with plastic inserts. The Tectite Pro range is for use with copper tube (manufactured to BS EN 1057). Maximum working pressures & operating temperatures: Tectite Classic fittings with copper pipe: 6.0 bar @ 95°C, 16.0 Bar cold water use. Tectite Classic fittings with PEX & Polybutylene 6.0 bar @ 95°C, 12.0 Bar cold water use. Tectite Pro fittings (15mm - 28mm): 6.0 bar @ 95°C, 20.0 Bar cold water use. Tectite Pro fittings (32mm - 54mm): 6.0 bar @ 95°C, 16.0 Bar cold water use.
Range of stainless steel (SS316L) pressfit fittings with EPDM ‘O’-rings for use with stainless steel pipe (manufactured to EN10312). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
Range of copper end feed fittings for use with copper tube to EN 1057. For above and below ground use. Maximum working pressure: 6mm-54mm 16.0bar, 64mm-108mm 10.0bar. Maximum operating temperature 85°C
WC dual flush valves with a plastic body and incorporates an internal overflow. Cold water use only.
WC dual flush valves with a plastic body and incorporates an internal overflow. Cold water use only.
Range of water meters with plastic bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of electromagnetic water meters with stainless steel bodies and natural rubber liners. Maximum working pressure 10.0 Bar Maximum operating temperature 50.0°C
Range of in-line single jet water meters with brass bodies. Products incorporate plastic strainers. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 85.0°C.
Range of in-line water meters with brass or plastic bodies. Models with a minimum length of 130mm and a maximum operating temperature of 50°C are supplied with an optional, non-return valve to be fitted by the installer (not suitable for backflow protection). Maximum working pressure 16.0 bar. The meters can be supplied with a maximum operating temperature of 50°C or 70°C.
Range of water meter manifolds with plastic bodies. The inlets incorporate a spherical valve. Models ending in ‘CGDM’ incorporate a single check valve cartridge and models ending in ‘CGDCVDM’ incorporate two, single check valve cartridges however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds incorporated into a meter chamber. The inlet of all models incorporates an isolation valve and an approved check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection. MK7000003003 is for use with MDPE plastic pipe (manufactured to BS EN 12202-1:2011). Maximum working pressure 12.5 bar. Cold water use only.
Self-priming single stage pump, with stainless steel body, plastic impellers, stainless steel shaft, NBR 'O'-rings and seals. Maximum working pressure 6.0 bar. Maximum operating temperature 45°C.
Range of pumps with plastic bodies, pistons and TPE diaphragm. For use with John Guest LLDPE pipe. The products incorporate non-return valves (not suitable for backflow protection). Maximum working pressure: 8.27 Bar. Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of cold-water supply booster sets, incorporating a stainless-steel manifold system and between 1 and 3 pumps. The booster sets also incorporate spherical valves, non-return valves (not suitable for backflow protection), pressure switches/sensors and expansion vessels. Maximum working pressure: 16.0 Bar. Cold water use only.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C
Range of cold-water supply booster sets, incorporating a stainless-steel manifold system and between 1 and 4 pumps depending on model. The booster sets also incorporate spherical valves and non-return valves. Maximum working pressure 16.0 Bar Maximum operating temperature 23.0°C
Range of combined storage and booster sets, incorporating a cold-water storage cistern, submersible pump, solenoid valve or alternative actuated ball valve, non-return valve (not suitable for backflow protection), isolation valves and expansion vessel. Maximum working pressure 10.0 bar. Cold water use only.
Range of overhead shower outlets with (brass bodies – various finishes) incorporating stainless-steel filter washers at the inlet. Maximum operating temperature 85°C.
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of overhead shower outlets with brass bodies (various finishes). The inlet incorporates a plastic flow regulator and stainless steel strainer. Maximum operating temperature 60°C
Range of shower handsets with plastic bodies incorporating an integral filter. The inlet incorporates a combined washer and a strainer, plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C. Open outlet use only.
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of drain taps with brass (or DZR brass, see models) bodies and non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of stainless steel interlocked or PVC reinforced (see models), PVC inner lined flexible hose assemblies (various finishes). Open outlet use only. Maximum operating temperature 65°C.
Range of PVC shower hoses with EPDM O-rings. Maximum operating temperature 65°C. Open outlet use only.
Range of plastic braided PEX lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Nimbus Compact range of combination heat pump units with enamel lined tank and stainless-steel coil. Fitted with a magnesium anode, expansion vessel and T&P valve set at 7 bar & 95°C. supplied with an inlet control group consisting of a pressure reducing valve, strainer, pressure relief valve and single check valve, and a tundish. Max working pressure 6.0 Bar Max operating Temperature 80 °C
Range of stainless steel hot water buffer tanks. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of unvented storage cylinders. The secondary circuit is fitted with a temperature and pressure relief valve set at 7.0 bar at 90˚C and an expansion relief valve set at 6.0 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Also Supplied with an expansion vessel and tundish. Maximum working pressures: Primary circuit: 5.5 bar Secondary circuit: 6.0 bar Solar circuit:6.0 bar Maximum operating temperature 85.0°C
Range of indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: Primary circuit: 6.0 Bar Secondary circuit: 5.5 bar Maximum operating temperature: 85.0°C
Range of 2, 3, 4, 5 or 6 port manifold assemblies with brass bodies. The products incorporate a spherical valve with a plastic ball on either the inlet or on each outlet (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of wall mounted concealed thermostatic blending valves, (brass bodies – various finishes). Model (TVT126001000xx) incorporates a quarter turn ceramic disc headwork. Model (TVS126003000xx) incorporates a two-way ceramic disc diverter headwork. Temperature is controlled independently via a thermostatic mixing cartridge that incorporates a manual override button. Both models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar or 10.0 Bar (see models). Maximum operating temperature 60°C.
Range of T-type blending valve with brass bodies and thermostatic cartridges. Compression models are for use with copper pipe manufactured to EN1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 75°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of eccentric lugged or wafer type butterfly valves with stainless teel or blue epoxy coated bodies and stainless steel or epoxy coated ductile iron discs, incorporating EPDM or PTFE seats (see models). Max working pressure: 10.0 Bar, 16.0 Bar or 20.0 Bar (see models). Max operating temperature 80°C or 99°C (see models).
Range of wafer and fully lugged butterfly valves (gear or handwheel operation) with a cast iron body (blue epoxy coated), EPDM seat and stainless steel disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves (gear or handwheel operation) with a cast iron body and disc (blue epoxy coated), EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar (Eurobrass 143 FF) or 3.0bar to 7.0bar (Eurobrass 143 FL). Maximum working pressure: 25.0 bar for Eurobrass 143 FF or 30.0 bar for Eurobrass 143 FL. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.
Pre-set pressure relief valves, pre-set at 3.0 bar, with a plastic body. Maximum operating temperature 85 °C.
Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of in-line spherical valves (brushed chrome DZR brass body) with lever or butterfly type operating members (see models), DZR brass ball (chromium plated brass) and PTFE seats and washers. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with brushed chrome plated brass bodies, chrome plated brass ball, PTFE seats and butterfly or lever operating member. Maximum operating pressure 40.0 bar. Maximum operating temperature 95°C
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of square operated spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
'Sigrafine® EK2239, EK2200, EK2230 & EK2240'. Grey coloured, compression moulded, phenolic resin impregnated carbon rings. For use with water up to 85°C.
'Dicoat 60 EX Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's user instructions 'SPL/R&D/TTD/UI/007', version '01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Factory applied, blue coloured epoxy coating. Apply as per manufacturers technical data sheet dated 9th November 2015. Cure for 2 minutes, 30 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JERLAC Two Pack Epoxy Beige-740'. Factory applied, two-part, beige coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's data sheet issue number '01', dated '10.01.2024'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 35530 System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘Hempadur 35530 red (51320) and Hempadur 35530 grey (10500)’. ‘Hempadur 35530 red (51320)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘Hempadur 35530 grey (10500)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet dated October 2024. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KLINGERSIL® C-4430'. NBR/fibre gasket material, which is green coloured one side and white coloured the other, manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
'Hylon N1040 H2 BK397 W & Hylon N1030 H2 BK397 W'. Black coloured, injection moulded, glass fibre filled polyamide materials. For use with water up to 60°C.
'27GFT'. Natural (appears white), extruded PA66+30GF material. For use with water up to 85°C.
'ULTRAMID® T7300EG10 FC Aqua BK23285'. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'PLUSTEK PAT302PWG50BK10'. Black coloured, injection moulded, glass-fibre reinforced polyamide material. For use with water up to 85°C.
'Celanex 3300-2FC EF2001 natural'. Natural (appears cream coloured), injection moulded PBT material. For use with water up to 60°C.
'Ecoleader® EL-4300'. Dark Yellow coloured (transparent), Vinyl Ester Resin material manufactured by casting moulding process. For use with water up to 60°C.
'NORYL WM330G-73701 (black), NORYL WM330G 7G8B4911 (grey) & NORYL WM330G-4G8B5291 (beige)'. Injection moulded PPE-PS materials. For use with water up to 85°C.
‘NORYL’ black coloured, grey coloured or beige coloured, injection moulded PPE + PS materials. FE1410PW – 73701. FE1520PW – 73701. FE1630PW – 73701. FE1740PW – 73701. FE1520PW - 4G8B5291. FE1630PW - 4G8B5291. FE1410PW – 7G8B4911. FE1520PW – 7G8B4911. FE1630PW – 7G8B4911. FE1410PW-4G8B5291, FE1740PW-4G8B5291 & FE1740PW-7G8B4911 were added to the approval in April 2025. For use with water up to 85°C
'NORYL WM300G-701 (black), NORYL WM300G-960 (grey), NORYL WM300G-801 (beige) & NORYL WM300G-845 (beige)'. Injection moulded PPE+PS materials. For use with water up to 85°C.
'DIC.PPS Z-230-JF BLACK-U'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Noryl PX1630 – 73701'. Black coloured, injection moulded PPE material. For use with water up to 85°C.
'OHJI Silicone Rubber Karyu3-type'. Grey coloured, extruded Silicone rubber material. Shore hardness 30. Tested in-radius size 2.75mm. For use with water up to 23°C.
'LOCTITE® 6300™’. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.1’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
WC douche set including a trigger spray, flexible hose and wall outlet with stop lever. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assembly. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator, and products are supplied with interconnecting stainless steel braided silicone lined flexible hose assemblies. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cisterns with a BS 1212- 4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a manually operated dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies, models AI-903215, Al-903222 & AI-903228 are chrome plated. Maximum working pressures: AI-903215, AI-903222 & AI-903020 16 bar. AI-903032, AI-903040 & AI-903050 10 bar. Maximum operating temperature 60°C Added September 2025 Maximum working pressure 10 Bar (AI-903025) Maximum working pressure 16 Bar (AI-903228) Maximum operating temperature 85°C
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of ceramic disc headworks with brass bodies. The 12333004-001 model is a 2-way ceramic disc diverter headworks. The 12333006-001 model is ¼ turn. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge and 2-way ceramic disc diverter headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Models 6500H/W & 6504/W are supplied with a click type waste – not verified by test. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 70 °C
A deck mounted two hole, single outlet (fixed) combination tap assembly, with a brass body (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with metal back nuts and plastic aerators. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of bath filler waste kits incorporating a brass inlet elbow and overflow assembly, a copper hex nut, overflow housing. Maximum Working Pressure 5.0 bar. Maximum operating temperature 70.0 C
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Deck mounted swivel spout outlet (chromium plated brass). Open outlet use only. Maximum operating temperature 65°C.
Range of chemical dosing equipment which incorporate self-closing valves within a plastic body with EPDM o-rings. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Only suitable for use with chemicals no greater than a FC3, additional backflow protection is required for chemicals greater than FC3. Maximum working pressure 9.0 bar. Maximum operating temperature 70ºC.
‘APL’ & 'AP' ranges of brass press fittings for use with ‘APE Multylayer' pipe. Connection is achieved via TH or U profile press jaws. AP range, only TH profile; APL range, TH and H profile; TH and H profile from DN 16 to DN32; TH for DN40, DN50 and DN63. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings for use with stainless steel pipe. Above ground use only. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of stainless-steel press fittings with EPDM ‘O’-rings and EPDM washers. For use with stainless-steel pipe. Joints are achieved using a press fitting tool. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of clamp fittings incorporating DZR brass bodies. For use with PE 100 RC pipe (manufactured to EN12201) only. Maximum operating pressure: 16 bar. Cold water use only.
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
‘Universal Transition Coupling (UTC)’ range of plastic compression fittings for use with the following pipe types and sizes: Stainless steel (manufactured to ASTM A554/ BS EN 10312): ¾”, 1” & 1¼”. Galvanised (EN 10255): ¾”, 1”, 1¼”, 1½” & 2”. Copper (BS EN 1057): 15mm, 22mm & 28mm. PVC (BS EN 1452): 20mm & 2”. ABS (BS 5391-1): 20mm, 25mm & 32mm. PE80 & PE100 pipe (to BS EN 12201): 20mm, 25mm, 32mm, 50mm & 63mm. For use above and below ground. Maximum working pressure 12.5 bar. Cold water use only.
Range of brass press fittings for use with copper pipe (manufactured to EN1057:2006 and +A1:2010 Seamless round copper tube, R250 half hard). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of copper end feed fittings for use with copper tube to EN 1057. For above and below ground use. Maximum working pressure: 6mm-54mm 16.0bar, 64mm-108mm 10.0bar. Maximum operating temperature 85°C
‘Zip Aquapoint IV’ range of wall mounted directly heated unvented storage vessels (cased and insulated) incorporating an enamel lined cylinder and safety kit. The cylinder is factory fitted with a temperature and pressure relief valve (7.0 bar/90°C) and a drain valve. The product is supplied with an installation kit comprising of an expansion vessel, tundish and an inlet manifold incorporating a 6.0 bar expansion relief valve, an adjustable pressure reducing valve with stainless-steel strainer (adjustable between 2.7 and 3.3 bar, but pre-set at 3.0 bar), and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The compression connections of the installation kit are for use with copper pipe (Manufactured to EN 1057). Maximum working pressure 5.5 bar. Maximum operating temperature 70°C. Cold supply only.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of ultrasonic water meters with plastic bodies and plastic strainers at the inlets. Specific models (see models) incorporate an optional non return valve (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 90°C.
Range of accumulators. The brass vessel connector of the ACC-060-TNK, ACC-120-TNK and ACC-180-TNK models incorporates a plastic flow regulator. Maximum working pressure 8.6 bar. Cold water use only.
Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
‘Vari RS’ range of single, twin & triple cold water booster sets. The products incorporate one or more pumps, expansion vessels, isolation valves and non-return valves (not suitable for backflow protection). The twin and triple models include a suction and discharge manifold. Maximum working pressures - see model. Cold water use only.
Range of single, twin & triple cold water booster sets. The products incorporate one or more pumps, expansion vessels, isolation valves and non-return valves (not suitable for backflow protection). The twin and triple models include a suction and discharge manifold. Maximum working pressures - see model. Cold water use only.
Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The Movitec VME models and VE/VSE models added May 2025 can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Existing models: Comeo C models 10.0 bar, Movitec VM models with an oval flange or VME models with integral check valve 16.0 bar, All other Movitec VM models 25.0 bar. Models added May 2025: Movitec V/VS models with an oval flange or VE models with integral check valve 16.0 bar, All other Movitec V/VS models and Movitec HI/HSI models 25.0 bar. Maximum operating temperatures: Existing models: Comeo C and Movitec VME models with integral check valve 60°C, all other model variants 100°C. Models added May 2025: Movitec VE models with integral check valve 60°C, all other model variants 100°C.
Range of single and twin ended shower booster pumps with plastic bodies and plastic impellers. The inlets/outlets incorporate stainless steel braided EPDM lined flexible hose assemblies with isolation valves and stainless-steel strainers. The outlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The Universal Twin models incorporate an expansion vessel. Maximum working pressure 1.5, 1.8, 2.0, 2.5, 2.6, 3.0 Bar (see model for more details). Maximum operating temperature: 60.0°C.
Shower handset with a stainless-steel body (various finishes - see model) and silicone nozzles. The inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 65°C.
Range of overhead shower and shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
Range of shower outlets, (plastic bodies - chrome plated) incorporating a plastic flow regulator. Products 24 540 xx0, 24 541 xx0, 24 550 xx0, 24 551 xx0 to be installed together with 24 573 180 Hansgrohe Raindance Alive Basic set. Maximum operating temperature 60°C. Open outlet use only.
Range of wall mounted shower shower heads (chrome plated brass) bodies. Maximum operating temperature 85°C. Open outlet use only.
Range of `Y`-patterned strainers with either brass or DZR brass bodies, incorporating a stainless-steel mesh strainer. Maximum working pressure: 25.0 Bar (1SYA Models) or 16.0 Bar (1SYC & 1SYD models) Maximum operating temperature 95°C. Strainers with compression connections are to be used with copper pipe manufacture to BS EN 1057. Strainers with M profile press-fit connections are to be used with copper pipe manufactured to BS EN 1057 & SS304 Stainless steel pipe manufactured to EN 10312.
Wall mounted bib tap with a nickel-plated brass body, chrome plated brass ball, NBR ‘O’-rings and gasket, and PTFE seats. The product incorporates a hose union outlet with an integral plastic flow straightener. Maximum working pressure 20.0 bar. Maximum operating pressure 85°C.
Range of pillar taps with brass bodies (chromium plated) incorporating either a quarter turn ceramic disc headworks with single lever operating members (TAP9013 model) or non-rising spindle headwork with dome type operating members (TAP1118 model). The spout outlets incorporate a plastic flow straingtener. The products are supplied with metal backnuts. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
Range of shower hoses with PVC outer (various finishes) and TPE liner. Maximum operating temperature 65.0°C. Open outlet use only.
Stainless steel braided hoses, incorporating a dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. The Click Seal 1TF300UKCSV model incorporates an isolation valve. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of EPDM or PVC lined, interlocked stainless-steel shower hoses. Open outlet use only. Hoses with an EPDM liner have a maximum operating temperature of 85°C. Hoses with an PVC liner have a maximum operating temperature of 65°C.
Range of stainless steel or nylon braided, PEX lined flexible hose assemblies with various brass end connections. Maximum working pressure 10.0 Bar. Maximum operating temperature 85 °C.
Range of ‘Ridgeline’ stainless steel flexible connectors. Maximum working pressure 6.0 bar. Maximum operating temperature 80°C.
temperature and pressure relief valve set at 7.0 bar@90˚C. A safety kit (manifold) consisting of a check valve cartridge (verified by test, suitable for backflow protection against Fluid category 2) strainer, an expansion relief valve set at 6.0 bar and pressure reducing valve set at 3.0 bar. A tundish, expansion vessel and a filling loop assembly, incorporating a stainless steel braided EPDM lined flexible hose, brass bodied isolation valve and a DZR brass non-verifiable double check valve assembly that incorporates an isolation valve. Maximum working pressures: Secondary circuit 5.5 bar. Primary circuit 3.0 bar Maximum operating temperature 90.0°C
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range of wall mounted thermostatic, bar type shower valves. Model (704309) incorporate quarter turn ceramic disc headworks and model (704308) incorporates a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed, thermostatic shower valves (brass bodies – various finishes) incorporating a ceramic disc diverter with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with dome type operating members incorporating a manual override button. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C
Range of wall mounted thermostatic bar shower mixers incorporating a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose, handset and riser rail assembly. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Wall mounted thermostatic blending valves (black or chrome plated brass), incorporating a half turn ceramic disc. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridges with stainless-steel strainers; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum temperature 60 degrees.
Non-metallic materials and components comply with BS6920 at 60°C
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of 2-way or 3-way ceramic disc diverters with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flow control valves with (chromium plated brass bodies) incorporating a ceramic cartridge headwork with single lever operating members and stainless-steel braided supply hoses. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C.
Range of spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated) and stainless-steel plates. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (brushed chrome brass bodies) with single lever or T handles operating members. Maximum working pressure; DN 8, DN 10, DN 15 – 50.0 bar. DN 20, DN 25 – 40.0 bar. DN 32, DN 40 – 30.0 bar. DN 50 – 25.0 bar Maximum operating temperature; 90°c
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass or brass bodies with chromium plated brass balls. Models incorporate lever or butterfly operating members. Maximum working pressure 10.0 Bar, 16 bar, 25 bar, 32 bar, 40 bar or 64 bar. Maximum operating temperature 100 °C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with brass (CP5R models), nickel plated brass (CP12 and CP02 models) or chromium plated brass (CP13 models) bodies, brass (10.20105.22X.CP5R-8510 and 10.20105.28X.CP5R-8510 models) or chromium plated brass (all other models) balls. The valves are either screwdriver, lever or butterfly handle operated (see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (10.60145.015.CP12-8510 and 10.61055.022.CP12-8510 models) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies and chrome plated brass ball. The compression and press-fit connections are for use with copper pipe (manufactured to EN1057). Jointing of the press-fit connection is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with stainless steel bodies, stainless steel ball and lever operating members. The press-fit connection is for use with stainless steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
UV Home’ range of UV disinfection units with 304L or 316L stainless steel bodies (see models). Maximum working pressure for UV HOME 2 & 3 is 6 bar. Maximum working pressure for UV HOME 6 & 9 is 10 bar. Maximum operating temperature 35°C.
'IUPITAL F30-EW'. Natural, (appears white coloured - opaque), injection moulded POM material. For use with water up to 85°C.
'ANUBIT HB-1000'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's TDS 'AE-TDS-023-2021', dated '02.08.2024'. Please note that use of a thinner isn't covered by the scope of this approval. Cure for 40 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac High Build Bituminous Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's work instruction document 'GPC/WI/10' issue no. '01', dated 03/01/2018. Cure for 72 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tuffkote Bituminous Aluminium'. Factory applied, grey coloured, two-component crude oil bitumen coating. Mix in a 17.1:2.9 volume ratio and apply as per manufacturer's data sheet 'SPL/PMG/2019100166', 'Rev 2', dated '04/2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'P.HSR 42.5-010Y'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'JXT/JS02-10', edition '1/0', dated '2021-11-30'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 451B'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS 'CR451B/CP573X', dated 'Sep 24, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Grilon AG-30 FWA Black'. Black coloured, injection moulded, PA66-GF30 material. For use with water up to 85°C.
'Radilon A RCM4010RKC 306 BK'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 85°C.
'Tecotek OP20 GR30 BG018 01 0A QF'. Beige coloured, injection moulded PPO/HIPS material. For use with water up to 85°C.
'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates a lever operated spherical valve and stainless-steel strainer. For use with BS EN1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-1 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-2 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-3 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No |
D30PF and D30PF-1 only different in the color of Item 11 and Item 13 D30PF-2 and D30PF-3 only different in the color of Item 11 and Item 13 DN30PF and D30PF-2 only different in the shape of Stem
Range of deck mounted ceramic cartridge and single sequential headwork assemblies, (brass bodies – various styles and finishes), incorporating a range of operating members. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic discs headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (white finish), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 65°C.
Combination Tap assemblies incorporating ceramic cartridge or ceramic disc headworks.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T10105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T20405 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21005 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T30605W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T31505 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40105W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T40205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T40415 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T50805 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
1.The model number suffix without B indicates chrome plated. The model number suffix with B indicates black. The model number suffix with BB indicates Brushed brass. 2.Only SL-T40415, SL-T40205 & SL-T40105W suffix with G indicates Champagne Gold.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21001 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T31501 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T50801 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T30601W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T20401 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T40201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40401R | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40101W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T10101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
Range of two hole, double outlet (swivel) combination tap assemblies (chromium plated brass). The TAP2014 model incorporates non-rising spindle headworks with dome type operating members. The TAP 9023 model incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CLS201 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS211 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS214 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS215 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS210 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS220 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS230 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22D | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22E | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
Finishes available: Chrome, Brass, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Vintage Brass, Gold, Matte Gold.
Range of three hole, metal, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlets incorporate plastic aerators. The products incorporate stainless steel braided, silicone rubber (TPSiV) lined inter-connecting hoses. The products are supplied with metal back nuts and click type pop-up wastes (not verified by test). Maximum working pressure: 6.0 Bar. Maximum operating temperature: 65°C.
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Range of stainless-steel expansion joints. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
‘Center Pot’ range of expansion vessels. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of filter shower handsets and tap outlets with plastic bodies with EPDM O-Rings Open Outlet use. Maximum operating temperature 60°C
‘GM50xx’ range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *- STPT304 and *- STPT316 stainless steel pipes. The GM5004 prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
‘Uponor Q&E’ range of brass press-fit fittings for use with PE-Xa-PE-PE ‘Uponor Aqua Pipe AU’ multi-layered pipes. Maximum operating pressure 10 bar. Maximum operating temperature 70°C.
Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Mingshi stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Hyddro Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Hyddro stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of brass compression fittings for use with copper pipes and Irish copper pipe (both manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: 32612, 32634, 32712 & 32734 models: 65°C. All other models: 85°C.
‘Instantor Lead-Free Brass’ compression fittings with DZR brass body, for use with DZR Copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C. Cold supply only.
Range of counter-top or under-sink electrical water heaters. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C, except 65°C for 10L models.
Range of counter-top or under-sink electrical water heaters. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C, except 65°C for 10L models.
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.
Range of rotating piston, volumetric in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Cold water use only.
GKMV30P range in-line volumetric water meters with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only.
GKMV30P range in-line volumetric water meters with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of ‘SureCal’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.
Range of multi-stage semiaxial submersible pumps with stainless steel bodies and impellers. Please note, this approval does not cover the motor, motor connection kit or power cable necessary for the pump to operate. Open outlet use only. Cold water use only.
STORMBOOST range of domestic water pressure booster pumps with brass impellors, brass bodies with accumulators, available from 60 – 300 litres (please refer to model). Models are supplied with reducing bushes, pressure gauges, pressure reducing valves and double check valve assemblies housed in DZR brass bodies with isolation valves and strainers. Maximum working pressure 4.5 bar. Maximum operating temperature 23°C.
’TP Series 300’ and ‘TPE Series 300’ ranges of single stage in-line pumps with black coloured cataphoretic electro deposition coated cast iron or ductile iron bodies and bronze, stainless-steel or black coloured cataphoretic electro deposition coated cast iron impellers. Pumps are available with BQQE or BBQE shaft seals. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of shower handsets and overhead showers with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless-steel filter and a plastic flow regulator. Maximum working temperature 45°C. Open outlet use only.
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of ‘Y’-pattern strainers with blue epoxy coated ductile iron bodies and a stainless-steel screen. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted bib tap with chrome plated brass bodies, incorporating either non-rising spindle headworks with cross top operating members or quarter turn ceramic disc headworks with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Wall mounted hose union taps with brass bodies, incorporating a rising spindle headwork with a ‘T’ type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel braided EPDM lined flexible hose assemblies with EPDM seals & EPDM washers, available with a variety of end connections. For use with copper pipe manufactured to EN1057 & HEP20 PB pipe. Maximum working pressure; 6 Bar Maximum operating temperature; 65°c
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313963 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 309644 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| AR3 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313960 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| DEL SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286569 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285401 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286565 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286566 | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286567 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285400 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313962 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313965 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BB | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BLK | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311671 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311672 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311673 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 231844 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313961 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV GM | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCVO C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Shower set comprising of a wall mounted shower valve, riser rail, shower handset, shower hose and overhead shower outlet. Flow in controlled by a ceramic disc headwork with dome type operating member. Temperature is controlled via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Each inlet of the shower valve incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of thermostatic mixing valves in various finishes, model XX3001YY has one outlet, temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc valve, model XX3002YY has 2 outlets temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc cartridge and model XX3003YY has 3 outlets temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc cartridge. Inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, nickel plated brass ball and PTFE seats. The LD 47.300.XX and LD 47.302.XX models have a butterfly handle. The LD 47.301.XX and LD 47.303.XX models have a lever operating member (normal and special type). The LD 47.340.XX and LD 47.342.XX models have a T-handle. Maximum working pressures: ½” - 1” sizes: 40.0 bar, 1¼” - 2” sizes: 25.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with either DZR brass Nickel-plated brass or chromium plated brass bodies, nickel plated brass ball and PTFE seats. With either lever or butterfly operating members. Some models incorporate a stainless-steel filter. Compression models for use with copper pipe manufactured to EN 1057. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or chromium plated brass and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with DZR brass bodies. Operating members are either handwheel operated or lockshield. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
'Powercron® 6070 B coating'. Factory applied, black coloured resin based coating. Apply as per manufacturer's TDS 'CR607B/CP588B'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 2 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
