Standpipe assembly break tank with a Type ‘AB’ air gap (verified by test – suitable for backflow protection against fluid category 5) mounted to the top of the standpipe body. The tank is filled via a compact float valve and has two screened weir slots. Water is then supplied by gravity from the break tank to the hose outlet below. Flow is activated via a spherical valve located behind a lockable panel. In addition to the isolation valve, the product incorporates a single check valve assembly (suitable for backflow protection against Fluid Category 2) prior to the spherical valve and an in-line ‘Y’ pattern strainer after it. The spherical valve includes a drain plug to allow for draining. Insulation is provided up to the drain point. Maximum working pressure 10.0 bar. Cold water use only.
DC type pipe interrupter with a permanent atmospheric vent (DZR brass body) incorporating a flow regulator at the inlet and brass shroud. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with plastic guide, stem and housing, stainless steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, silicone gaskets and seals. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Thermostatic cartridge incorporating brass bodies and stainless steel filters. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating brass bodies, stainless steel strainers and EPDM ‘O’-rings. For insertion into specifically dimensioned tap bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of deck mounted combination tap assemblies (chromium plated brass) incorporating rising spindle headwork with single lever operating members, swivel spout outlet and separate pull-down spray outlet (with self-closing trigger assembly). The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Models 98008-M001 & 98008-1 are single hole, single outlet. Model 98007-1 is two-hole, single outlet. Model 98001-2 is single hole, double outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted combination tap assemblies (chromium plated brass) incorporating rising spindle headwork with single lever operating members, swivel spout outlet and separate pull-down spray outlet (with self-closing trigger assembly). The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Model 98011-1 is single hole, single outlet. Models 98002-1 & 98002-M001 are two-hole, single outlet. Model 98002MN-2 is two-hole, double outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Range of single hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headworks with a single lever operating member. The inlets incorporate plastic strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets of ‘2820’ incorporate a spherical valve. The spout outlets incorporate a plastic flow straightener and the products are supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks with a single lever operating member. The inlets of model 2820 incorporates a flow restrictor and spherical valves. The spout outlets incorporate a plastic flow straightener and the products are supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. The product is available either as a version with a pop-up waste or one with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. The products are available either as a version with a pop-up waste or one with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Product is supplied with a T-Type thermostatic mixing valve. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating a thermostatic sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (chromium plated) brass bodies, incorporating quarter turn ceramic disc headworks or ceramic cartridge headworks (see models) with single lever operating members. The swivel spout of the TMO35SSCM model is (chromium plated) stainless steel. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated or brushed nickel coated brass), with quarter turn ceramic disk headworks and cube operating members. The spout outlet incorporates a plastic flow straightener. Supplied with single check valves (suitable for backflow protection against Fluid Category 2) with integral servicing valve for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass) with non-rising spindle headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 7.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disk headwork’s with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), Models M33136 & M1006 incorporate a quarter turn ceramic disc headwork with single lever operating members. Models M4306, M4306E & M4306F incorporate a non rising spindle headwork with dome type operating members. Model M4306G incorporate a non rising spindle headwork with cross top operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Two-hole, single outlet (fixed) combination tap assembly with a brass body (chromium plated), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet is a waterfall design. The inlets incorporate plastic flow restrictors. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet, (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of two hole, single outlet (swivel) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disk headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet swivel combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating non rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn rising spindle headworks with single lever operating members. The S8215AA model is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of deck mounted thermostatic shower mixers with brass bodies (chrome plated), incorporating ceramic disc headworks with dome type operating members controlling the flow and a lockable self-cancelling diverter to shower outlet. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Spout outlet incorporates a plastic flow straightener. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. Model DYN106 is supplied with a shower hose and shower handset, all other models are supplied with a shower hose, shower handset, riser rail and soap dish. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted two hole, double outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc (DLV305B, DLT305B) or rising spindle (CR305 “Bridge”, CR305/501 “Bridge” & GEO305) headworks. Models GEO305, DLT305B and DLV305B incorporate single lever type operating members. Models CR305 and CR305/501 incorporate cross top operating members. The products are supplied with plastic back nuts. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted two hole, double outlet (swivel) combination tap assembly (chromium plated brass) with quarter turn ceramic disc headworks and single lever type operating members. The product is supplied with plastic back nuts. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body with various finishes) incorporating quarter turn ceramic discs. No operating members supplied. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Three hole, single outlet (swivel) combination tap assembly with brass body (various finishes) incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted (swivel) spout outlets with chromium plated brass bodies, EDPM ‘O’-rings and a plastic flow straightener. DJ suffix models have a double swivel arm. Maximum operating temperature 65°C.
Range of free-standing sanitary macerating disposal units. The units are fed via a flexible hose assembly. Flow is controlled by a solenoid valve and discharges via a type `AA` air gap. Maximum working pressure 10.0 bar. Cold water use only.
Range of Irish compression fittings with brass bodies, nut and olives for use with Irish copper pipe manufactured to EN1057:2006+A1:2010. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of capillary end feed bronze fittings for use with copper tube (manufactured to BS EN 1057). 15mm – 54mm fittings have a maximum working pressure of 25.0 bar. 67mm – 108mm fittings have a maximum working pressure of 16.0 bar. Maximum operating temperature 100°C.
WC dual flush drop valve with plastic body silicone and rubber seal. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold Water Use Only.
WC dual flush drop valve comprising of a plastic body and silicone seating washer. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water only.
Range of WC flapper valves with a silicone seal, ABS body and internal overflow. The device is operated via a plastic chain to be connected to a cistern handle. Cold water use only.
Dual flush, WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water only.
Range of WC dual flush drop valve with plastic body silicone rubber seal and NBR rubber ‘O’-ring. The valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Copper heat transformer. Maximum working pressure 11.0 bar. Maximum operating temperature 95°C.
Range of domestic hot water units incorporating instantaneous or semi-instantaneous plate heat exchanger assemblies. The product incorporates a motorised control valve, managed primary and secondary pumps (see model), and a drain valve on both circuits. Maximum working pressures: 10.0 bar primary, 9.5 bar secondary. Maximum operating temperatures: 110°C primary, 85°C secondary.
Ranges of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger and pressurised central heating system incorporating an expansion vessel and pressure relief valve set at 3.0 bar. The supplies to both domestic hot water and primary are controlled via spherical valves. Products are supplied with a rigid filling loop or keyless filling link. Maximum working pressure of the primary circuit is 2.5 bar & maximum supply pressure of the secondary circuit is 8.0 bar. Cold water supply only. Maximum operating temperature 95°C.
Q4000 range of water meters incorporating stainless steel bodies, FKM rubber gasket and grey epoxy resin liner. Maximum working pressure 16.0 bar. Cold water use only.
`Groundbreaker Mk3` water meter box incorporating a concentric water meter manifold (plastic body) with screw down stop valve, single check valve (verified by test as suitable for backflow prevention up to fluid category 2) & compression fittings. The product is intended to be installed upon the external wall of a premises and incorporates internal insulation (insulation not verified by test). For use with MDPE pipe (manufactured to EN12201). Maximum working pressure 12.0 bar. Cold water use only.
Water hammer arrestor with brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Wall mounted outlet with detachable shower hose connector (42037UK model) and wall mounted shower outlet (42018UK model). The 42018UK model is supplied with an optional, detachable shower hose connector assembly which incorporates an integral plastic flow regulator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model 42037UK has a maximum operating temperature of 80°C. Model 42018UK has a maximum operating temperature of 60°C.
Range of 2,3 or 4 way manifolds incorporating a nickel plated brass body with non-rising spindle stop valves. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower outlet elbows with brass bodies (chrome plated,with exception of model 27.076.LS0). Some models incorporate a shower handset holder. The outlet incorporates a check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Intelligent water assist valve consisting of a motorised quarter turn shut off valve which operates in the event a leak on the supply pipe to which it is fitted. Maximum working pressure 10 bar. Cold water use only.
Range of in-line flow sensors with a plastic body, turbine and impeller case. Maximum working pressure 25.0 bar. Cold water use only.
Range of compact wall outlet assemblies with plastic bodies (chromium plated) and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 55°C.
Plug with nylon body and stainless steel shaft. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of black plastic bodied multistage, self or manually primed, high pressure centrifugal pumps with a stainless steel outer casing, plastic impellors, EPDM seals and ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of rotary vane (positive displacement) pumps with stainless steel bodies. Maximum working pressure 18.0 bar. Cold water use only.
Multistage, vertical booster pumps with a brass body and stainless steel pump housing, stainless steel impellers and EPDM ‘O’-rings. The 41782 (MV90 4M VSD) model includes a pressure transducer. Maximum working pressure 6.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel (AISI 304) bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Maximum operating temperature 90°C.
Range of magnetic drive volumetric rotary vane pumps with a plastic housing and built-in relief valve. Maximum working pressure: 22 series models - 20.0 bar, 20 series models - 14.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum operating pressure 11.0 bar. Maximum working temperature 90°C.
Range of pump units with plastic bodies and impellers, EPDM ‘O’-rings, expansion vessel with an EPDM membrane and a carbon graphite/ceramic/NBR shaft seal (bt-ar 13 bx 4ff xp). Each pump inlet incorporates a non-return valve. Single versions are standalone pumps, twin versions also include stainless steel manifolds. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted shower kit with brass bodies (various finishes) consisting of a shower rail with an overhead shower rose, incorporating a manual diverter to shower handset. Shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models AOOSCPUK and AOOSBKUK consist of just a shower handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of hand held shower outlets incorporating plastic bodies and over head showeroutlets incorporating brass bodies. Model 46127 includes a handset and hose with a single check valve fitted at the inlet and outlet to the shower hose (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). model 46154 includes a single check valve in the shower handset (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). Over head shower (model 46150) outlets have an adjustable elbow connection. Maximum operating temperature 60°C.
Range of shower arms and brackets with brass bodies (various finishes). Shower brackets incorporate single check valves cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Maximum operating temperature 85°C.
Range of shower handsets incorporating chromium plated plastic or chromium plated brass bodies (see model). Inlets incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of overhead shower outlets incorporating brass bodies (chrome plated) and EPDM gaskets. Inlets have stainless filters incorporated within a ball joint. Maximum operating temperature 85°C
Range of overhead shower outlets (chrome plated plastic bodies). Inlets incorporate a strainer. Maximum operating temperature 85°C
Range of shower outlets with brass bodies (various finishes) incorporating NBR ‘O’-rings (280R/W model) or EPDM ‘O’-rings (286P/W model). The inlet of the 286P/W model incorporates a plastic flow regulator. Maximum operating temperature 60°C.
Range of wall mounted shower outlets (brass bodies), shower hoses and handsets available in various finishes (see model). The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of inline ‘Y’- patterned strainers with brass bodies & stainless steel filters. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bib taps incorporating either brass or DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps (brass, chrome plated brass or DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted taps (chromium plated brass) incorporating non-rising spindle headworks with cross top operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps (chromium plated brass) incorporating non rising spindle headworks and cross top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps (chromium plated brass) incorporating non rising spindle headworks and cross top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator (expect models M5001 and M5002). The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Range of pillar taps incorporating brass bodies (chrome plated), non-rising spindle headworks (models 922031 & 922033) or quarter turn ceramic disc headowks (all other models). The spout outlet incorporates a flow straightner. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of pillar taps incorporating brass bodies (chrome plated), non-rising spindle headworks (model 922038) or quarter turn ceramic disc headowks (model 922068). The spout outlet incorporates an flow straightener Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrorme plated brass) with ¼ turn ceramic disc headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrorme plated brass) with ¼ turn ceramic disc headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Range of pillar taps (chrorme plated brass) with ¼ turn ceramic disc headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrorme plated brass) with ¼ turn ceramic disc headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Self-closing basin tap assembly (chromium plated brass) incorporating spring loaded headwork and dome type operating members. The inlet incorporates a plastic flow restrictor and the spout outlet incorporates a plastic flow straightener. The product is supplied with a metal backnut. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
Range of stainless-steel braided EPDM lined flexible hose assemblies, incorporating EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of PEX lined stainless steel braided flexible hoses with various brass end connections Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of EPDM lined stainless steel braided flexible hoses with various brass end connections Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of stainless steel and ACB braided hoses with and EPDM liner and various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC. Hoses with plastic push fittings: maximum working pressure 6.0 bar. Maximum operating temperature 65ºC.
Chrome plated interlocked stainless steel shower hose with an EPDM inner liner and EPDM gaskets. Maximum operating temperature 85°C.
Range of free standing direct gas fired unvented cyliners with a enamel coating internal lining and magnesium sacrificial anode. Fitted with a combined temperature and pressure relief valve set at 7 bar. Maximum working pressure 6.5 bar. Maximum operating temperature 80°C.
Automatic air venting valve with brass bodies, stainless steel float and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 120°C.
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
Range of air venting valves with a blue epoxy coated ductile iron body and carbon steel cover, NBR ‘O’-rings and EPDM seals. Maximum working pressure 10.0 bar or 16.0 bar (see model). Maximum operating temperature 65°C.
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
Range of wall mounted, concealed, manual blending valves incorporating brass bodies and quarter turn ceramic disc headworks. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of wall mounted, concealed, manual blending valves with either a dome type or single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of wall mounted, concealed, manually operated blending valves with brass bodies (various finish trim kits - see model) incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, manually operated blending valve, (brass body with a chromium plated brass trim set), incorporating a ceramic cartridge headwork with a single lever operating member controlling temperature and flow, and a manual diverter controlling the flow to the shower hose and handset or a secondary shower outlet. The product is supplied with a shower hose and handset. The handshower outlet connection and the shower handset inlet both incorporate an approved check valve cartridge, however the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, manually operated, concealed blending valve with a brass body incorporating a ceramic cartridge headwork with a single lever operating member controlling both flow and temperature. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Wall mounted manually operated, concealed blending valve (brass body) incorporating a ceramic cartridge headwork controlling both flow and temperature with single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Concealed, wall mounted, manual shower blending valve incorporating a brass body, ceramic cartridge headwork and a self-cancelling diverter to a second shower outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted (vertical) thermostatic blending valve (chromium plated brass) incorporating a non-rising spindle headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. The inlets incorporate stainless steel strainers and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted, bar type thermostatic shower mixers (chromium plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow with single lever operating members. The temperature is controlled independently via a thermostatic cartridge with single lever operating members. Both inlets incorporate a stainless steel strainer and a single check valve cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of concealed thermostatic blending valves with brass bodies and trim sets (various finishes - see model). The temperature is controlled via a thermostatic cartridge with a dome type or single lever operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Adjustable T-type thermostatic mixing valve (chromium plated brass). Each inlet incorporates a stainless-steel strainer and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.
Range of wall mounted, thermostatic blending valves with brass bodies (various finishes), incorporating a quarter turn ceramic disc headwork controlling the flow with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member which incorporates a manual override button. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of T-type thermostatic mixing valves with chrome plated DZR brass body, EPDM’O’-rings and NBR/fibre galsets (except for 252100 CST model). Maximum working pressure 14.0 bar. Maximum operating temperature 100°C.
Range of wall mounted thermostatic bar type mixing valves incorporating chrome plated brass bodies, ceramic disc headwork with dome type operating members controlling the flow. The temperature is independently controlled by a thermostatic cartridge with dome type operating member which incorporates a manual override button.The inlets incorporate stainless-steel strainers and an approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is supplied with a shower hose, shower handset and riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted bar type thermostatic shower valves (chromium plated or matt black coated brass) incorporating a manual diverter and quarter turn ceramic disc headwork controlling the flow between an overhead shower outlet or a shower handset with dome or cube type operating members. The temperature is controlled independently via a thermostatic cartridge with dome type operating member that also incorporates a manual override button. Models 801540 FF and 801540 FF MBK1 are also supplied with Fast Fit connections Both inlets incorporate stainless steel strainers and approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Wall mounted, concealed thermostatic shower valve incorporating quarter turn ceramic disc headwork with dome type operating members controlling the flow to multiple shower outlets. The temperature is controlled independently via a thermostatic cartridge with dome type operating member. The inlets incorporate an approved check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves, riser rail, shower handset, shower hose and overhead shower outlet. The valve incorporates a brass body (various finishes) and ceramic disc headwork with dome type operating member which controls and diverts the flow between the two shower outlets. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel filters and a single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with cube type operating member. Temperature is controlled independently via a thermostatic cartridge with a cube type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with cube type operating member. Temperature is controlled independently via a thermostatic cartridge with a cube type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Range of wall mounted, exposed, thermostatic bar type shower mixing valves (chromium plated brass). The F061 & 081 prefix models incorporate a 2-way ceramic disc diverter headwork with dome (F06 prefix models) or cubed type (F08 prefix models) operating members controlling the flow either shower outlet. The F062 & 082 prefix models incorporate a ¼ turn ceramic disc headwork with dome (F06 prefix models) or cubed type (F08 prefix models) operating members controlling the flow to a single shower outlet. The temperature is controlled independently via a thermostatic cartridge. The inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted, exposed, thermostatic bar type shower mixing valve (chromium plated brass) incorporating a 2-way ceramic disc diverter headwork with a dome type operating member, which diverts the flow between outlets. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a combined NBR washer and stainless steel strainer and an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valves with a chromium plated brass body incorporating a spindle headwork controlling the flow and a separate thermostatic cartridge controlling the temperature, both using single lever operating members. Both inlets incorporate flow regulators, strainers and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with shower hose, shower handset and riser rail. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, thermostatic blending valves with brass bodies (chrome plated), incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type or single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type or single lever operating member which incorporates a manual override button. The inlets incorporate a combined NBR washer and stainless strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of handwheel operated butterfly valves with blue epoxy coated ductile iron bodies, EPDM seat and stainless-steel disc. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with plastic body and disc and EPDM rubber seat and ‘O’-rings. Maximum working pressure 10.0 bar. Cold water use only.
Wall mounted, concealed, two-way manual diverter valve which diverts the flow between two shower outlets. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of diverter valves with a plastic body and ceramic discs.For insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of pilot operated float control valves with blue epoxy coated ductile iron bodies, NBR ‘O’-rings and gaskets. The products have flow control facility controlled via a float operated pilot valve. Supplied with auxiliary components including stainless steel pipe, spherical valves, Y-pattern strainer and a needle valve. Maximum working pressure 8.0 bar. Cold water use only.
Concealed flow control valve with a brass body incorporating a quarter turn ceramic disc headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Wall mounted, knee operated, self-closing flow control valve (chromium plated brass) incorporating a spring-loaded headwork with a single lever operating member, EPDM washers and seat. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of spring loaded, resilient trim, non-return valves (blue epoxy coated cast iron body), with bronze bushing, stainlesss steel spring and disc, and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, resilient trim, non-return valves (blue epoxy coated cast iron body), with bronze bushing, stainlesss steel spring and disc, and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Wafer type spring loaded, resilient trim, non-return valve with stainless steel bodies, springs and guides, and an EPDM seat. Not suitable for backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies. Adjsutable between 1.0 bar and 5.5 bar outlet pressure. Compression models are for use with copper pipe to EN1057. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 80°C.
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated) EPDM diaphragm and NBR ‘O’-rings. The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, pilot valve and needle valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 1.5 bar - 8.0 bar. Maximum operating temperature 80°C.
Range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of latching solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C
Range of normally closed solenoid valves with brass bodies, stainless steel spring, EPDM seal and diaphragm. Maximum working pressure - WZS1DF prefix models 7.84532 bar, WSLP1DF prefix models 9.80665 bar. Maximum operating temperature 85°C.
Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and an integrated flow meter sensor. Both the inlet and the outlet incorporate a white plastic flow restrictor. The products are also supplied with an optional EPDM outlet gasket, for installation over the outlet spigot. Maximum working pressure 10.0 bar (to diaphragm). Maximum operating temperature 85°C.
Spherical valve incorporating a brass body (brushed chrome), chrome plated brass ball, ‘y’-patterned strainer, PTFE seats and single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of angled servicing valves with brushed chrome plated DZR brass bodies and ball.The product incorporates a stainless steel strainer and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Smart water meter monitor with an integrated motorised shut off valve, piezo electric ultrasonic tranducer and pressure sensor, plastic housing and silicone ‘O’-rings. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chromium plated brass ball, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Isolation valve incorporating a brass body (chromium plated) and brass ball (chromium plated). Maximum working pressure 10.0 bar. Cold water use only.
Range of lever operating spherical valves incorporating brass bodies (nickel plated), brass ball (chromium plated) and PTFE seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Aladdin Easyfit Isolator Pro’ valve incorporating a stainless steel body and self cutting blade to enable a connection to a pressurised or wet systems. For use with copper pipe to BS2871 – EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of DZR brass gate valves incorporating brass wedges. The Fig 30 range incorporates hand wheel operating members. The Fig 30LS range incorporates a lock shield operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating DZR brass bodies and wedges, non-rising spindles and handwheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-rising gate valves with blue epoxy coated ductile iron body and EPDM rubber coated wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Range of gate valves with blue epoxy coated ductile iron bodies, a ductile iron wedge encapsulated in EPDM rubber, PTFE seals and EPDM gaskets and ‘O’-rings. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
DZR brass bodied angled screw down stop valve valve with EPDM seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of one way and two way manually operated needle valves incorporating brushed stainless steel bodies, rising spindle balancing mechanism and EPDM ‘O’-rings with a metal seat. Maximum working pressure 25.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
Range of polyethylene pressure vessels with spun (blue) fibre glass casing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
'Deep High Build Liquid Bitumen Paint'. Factory applied, black coloured bitumen paint. Apply and cure as per manufacturer's instructions reference 'DI/BP/2021/011' dated April 15, 2021. For use with water up to 60°C.
'P658RC & CY10C washers'. P658RC is a black coloured, polyester resin impregnated carbon washer. CY10C is a dark grey coloured, phenolic resin impregnated carbon washer. For use with water up to 85°C.
'SC4'. Factory applied, clear PTFE coating, intended for use with `O` rings, seals & gaskets. Apply as `Superior Group Quality Management System Procedure Reference 8.6’ referenced in document `LDAP-008 issue 1` released 01/05/2020. For use with water up to 85°C
`Suns-02`. Grey coloured, factory applied cement mortar. Mix, apply and cure as per user instructions 'doc: SUNS-U110320, version B` dated 2015-12. Cure for 24 hours@25°C. Between 1st May 2021 and 30th March 2022, the cement mortar is suitable for use with water up to 23°C. Between 31st March 2022 and 31st May 2026, the cement mortar is suitable for use with water up to 60°C
`Jin Dapeng WEY-Black, WEY-Red & WEY-Blue`. Factory applied epoxy coatings. Apply and cure as per manufacturer's instructions 'version no: JDP2015-01' dated 24th November 2015. For use with water up to 85°C.
'HSL-0588-3 Silicon Coating'. Factory applied, translucent silicon coating. Apply and cure as per manufacturer's instructions version 'BLT19.05 A'. For use with water up to 85°C.
'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-2'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement, sand & water in a 1:1.7:0.55 mass ratio. Cure for 5.5 hours@65°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BGDI01 Sulphate Resistant Cement & BGDI02 Portland Cement'. Factory applied, grey coloured cements. Mix 1 part cement, 2 parts sand and 0.25 parts water. Cure for 10 hours@23°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'Parasakti Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resistant cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CeramycGuard for use with QuartzSeal'. Site applied, white coloured (once mixed) polymer based concrete surface treatment. 'CeramycGuard’ is a three-component base coat comprising of Part A (clear liquid), Part B (grey powder) & Part C (clear liquid). Mix Parts A, B & C in a volume ratio. Rest for two minutes, apply as per manufacturer's instructions for use 'version 2' dated 'April 2021' and then cure for 24 hours@21°C. ‘QuartzSeal' is a white coloured, single-component topcoat. Apply as per manufacturer's instructions for use 'version 2' dated 'April 2021'. Cure for 7 days@21°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Yorkshire Flux 130 (White)`. White coloured paste flux. For use with water up to 85°C.
'LATTYflon 2790AL'. Cream coloured, PTFE/silicone braided rope with a square cross-section. For use with water up to 23°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'Solico Ivory GRP Panel'. Beige coloured, compression moulded GRP panel. For use with water up to 60°C.
'JUSTLINK® JLPEX'. Single layered, off-white (translucent), extruded PEX hose. For use with water up to 60°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'3301 black (330160415BLK)'. '3301 black (330130415BLK)' was added to the approval in November 2023. Black coloured, single sided polyethylene foam tapes with acrylic adhesive system. For use with water up to 23°C.
'LSPE-BE002 PE Pipe (Deep Blue)'. Blue coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BE002 PE Fitting (Deep Blue)'. Blue coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, extruded polyethylene pipe. For use with water up to 60°C.
'LSPE-BK001'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'ajpipe HDPE Pipe'. Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 50°C. From January 2024 the pipe is for use with water up to 60°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
`Revolve N-650/6068 Natural (appears cream coloured) & M-668 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'Revolve N-307 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Ryton XE-5501BL'. Dark grey coloured, injection moulded PPS material. For use with water up to 23°C.
`Aqua-Plus Fittings`. Green coloured, injection moulded polypropylene fittings. For use with water up to 70°C.
'EP80/2 BLK 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Tested in-radius size 1.5mm. For use with water up to 85°C.
EP80/2 BLK 'O' rings & gaskets. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 80. Tested in-radius size 1.5mm. . For use with water up to 85°C.
`EP1/1/5 BLK 'O' rings, seals & gaskets'. Black coloured, injection moulded EPDM 'O' rings, seals & gaskets. Shore hardness 70. The 'O' rings & gaskets have a tested in-radius size of 1.5mm. The seals have a tested in-radius size of 0.8mm. For use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 60°C.
`H34-50 to H34-70’. Range of black coloured, compression moulded EPDM rubber materials with a shore hardness of between 50 & 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP60-WAUK-FR'. Black coloured, compression moulded EPDM sheet material. Shore hardness 60. In-radius size 1.35mm. For use with water up to 23°C.
‘EPDM 825-c’. Black coloured, compression moulded EPDM sheet material. Shore hardness 80 A. Tested in-radius size 1.0mm. For use with water up to 23°C.
`SP402`. Black coloured, compression moulded, natural rubber material. Shore hardness 75. Tested in-radius size 1.00mm. For use with water up to 23°C.
'WN60/1 BLK 'O' rings'. Black coloured, injection moulded NBR 'O' rings. Shore hardness 60. Tested in-radius size 1.31mm. For use with water up to 60°C.
`WN 22/1/9 BLK` 'O' rings. Black coloured, injection moulded, nitrile rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 65°C.
'LS80T-1201 White'. White coloured, injection moulded silicone rubber gasket. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'5080SIL310P‐N' (natural - clear) & '5080SIL310P‐B' (black coloured). Extruded, silicone rubber hoses. Shore hardness 70. Tested in-radius size 0.75mm. For use with water up to 85°C.
'AJSIL-001'. Natural (appears white in colour), compression moulded silicone rubber material. Shore hardness 50. Tested in-radius size 2.0mm. For use with water up to 85°C.
'Permabond 102, 240, 105 & 2010'. Site applied, single-component, colourless adhesive/sealants. Apply as per manufacturer’s technical data sheets. Cure for 24 hours at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
BS EN 997:2018 RAK Compact Rimless Wall Hung 700mm COMRIMWH W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern with a side entry compact type float operated inlet valve which discharges via a Type AG airgap and a dual flush pneumatic drop valve capable of full flush volumes of 4.5 litres and a reduced flush of 3 litres. The inlet connection hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
DC type pipe interrupter with a permanent atmospheric vent and DZR brass body and EPDM gasket. Maximum working pressure 3.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and NBR seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridges incorporating plastic guides and stem, NBR or EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of single check valve cartridges incorporating a plastic body, stainless steel spring, NBR or EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and silicone seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar Maximum operating temperature 65°C.
Robocheck-1 in-line single check valve assembly with a DZR brass body (brushed chrome). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headwork assemblies with brass bodies, NBR ‘O’-rings and silicone gaskets. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and pull out spray. The spout outlet incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The product incorporates a pull-out spout outlet with a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. Model BTZ 1HF C incorporates a plastic flow straightener. Model BTZ SMBAS C incorporates a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator and the product is supplied with a pop up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating ceramic cartridge headworks and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chrom plated). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with single check valves with integral servicing valve for both inlets (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly with a brass body (chromium plated), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet is a waterfall design. The inlets incorporate plastic flow restrictors. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. This product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable self- cancelling diverter to the shower outlet. The waterfall spout outlet incorporates a stainless-steel aerator. The product is supplied with metal backnuts, as well as a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks and dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Pillar unions incorporating chrome plated brass bodies. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Three hole, wall mounted, concealed basin mixer with a brass body (chrome plated) consisting of a rough in set 45089 and extermnal trim 46090. Incorproating a quarter turn ceramic disc headworks and single lever operating members.The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Filling link assembly, incorporating a sliding manifold with EPDM ‘O’-rings, isolation valves and an isolation valve with a double check valve assembly (verified by test as suitable for backflow protection against Fluid Category 3). Maximum working pressure 10.0 bar. Cold water use only.
Water filter with polypropylene body. Maximum working pressure 8.6 bar. Cold water use only.
Range of brass compression fittings for use with copper pipe (manufactured to IS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of brass compression fittings for use with copper pipe IS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of press fittings incorporating brass or PVDF bodies and EPDM ‘O’-rings. For use with Henco standard PE-Xc/AL/PE-Xc pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of press fittings incorporating stainless steel bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of capillary solder ring fittings (bronze body) for use with copper tube (manufactured to to BS EN 1057). Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of compression fittings incorporating polypropylene bodies, plastic pipe liners, plastic grip rings and EPDM seals. For use with both PE80 & PE100 pipe manufactured to BS EN 12201. For above and below ground use. Maximum working pressure 12.5 bar (PE80 pipe 20mm - 63mm). Maximum working pressure 16.0 bar (PE100 pipe 20mm - 63mm). Maximum working pressure 10.0 bar (PE100 pipe 75mm - 110mm). Cold water use only.
Range of crimp fittings with a bronze body incorporating EPDM O-rings. For use with copper pipe manufactured to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Dual flush, WC outlet valve with internal overflow, operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of single and dual flush WC outlet valves with ABS body and EPDM seating washers. The valve incorporates an internal overflow and is operated via a push button assembly for either full or reduced flush. Cold water use only.
Dual flush WC outlet valve with ABS body and EPDM seating washers. The valve incorporates an internal overflow and is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of dual flushing WC outletvalves with plastic bodies and silicone gasket. Cold water use only.
Range of wastewater heat recovery systems incorporating a double wall stainless steel corrugated pipe. Maximum working pressure 16.0 bar. Cold water use only.
Range of wastewater heat recovery systems incorporating stainless steel corrugated pipe. Maximum working pressure 16.0 bar. Cold water use only.
Range of unvented electric storage water heaters consisting of a mild steel, glass/enamel coated tank, heating element and pressure relief valve set at 6.0 bar. Maximum working pressure 5.5 bar. Maximum operating temperature 75°C.
Range of vertical vented cased copper cylinders with indirect coils. The secondary circuit incorporates a thermostatic mixing valve. The inlet consists of a ball valve with strainer, inline non verifiable single check valve and mini shock arrestor. Cylinder are supplied with a factory fitted immersion heater. Maximum working pressure - secondary 6.0 bar, primary 2.2 bar. Maximum operating temperature - secondary is 60°C, primary 85°C
H4000 range of helical rotor bulk water meters, with blue epoxy coated cast iron bodies and NBR ‘O’-rings. Maximum working pressure 16.0 Bar. Cold water use only.
Range of flow meters incorporating black epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with blue epoxy coated brass bodies and a plastic strainer on the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Range of water meter manifolds incorporating DZR brass bodies, PTFE washers, a non-return valve and ball valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed wall insulation unit with a brass body and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of isolation valves with a brass body (various surface finishes - see model) and either a quarter turn ceramic disc (PEX-230-C/P and PEX-231-C/P models) or a non-rising spindle (all other models) with various operating members (see model) and NBR ‘O’-rings. The inlet of the PEX-230-C/P and PEX-231-C/P models incorporates a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall bracket with a brass body (chrome plated) and EPMD ‘O’-rings. Maximum operating temperature 85°C.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: EH Three phase models 85°C, EH Single phase models 55.0°C and EHsp models 35°C.
Range of self-priming pumps with stainless steel bodies and impellers, and EPDM ‘O’-rings. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of single stage end suction pumps with stainless steel or cast iron pump housings, EPDM ‘O’-rings and wear rings available in low-lead bronze/brass or stainless steel. Cast iron models are coated in black cathodic paint (textured finish) or black epoxy (smooth finish). The pumps are available with carbon graphite/silicon carbide mechanical shaft seal. Impellors are available in cast iron with black cathodic paint, low-lead bronze or stainless steel. The pumps are available with fixed flange, as well as loose flange (model dependent). Maximum working pressure 10.0 or 16.0 bar depending on model. Maximum operating temperatures: Stainless steel and cast iron with (smooth) epoxy coating pumps 85°C. Cast iron pumps with (textured) cathodic paint coating are cold water use only.
Centrifugal pump with a stainless steel casing and shaft, silicon carbide and EPDM shaft seals, NBR ‘O’-rings and washers. Maximum working pressure 8.0 bar. Maximum operating temperature 45°C.
Range of inline circulating pumps with bronze bodies, plastic impeller and EPDM rubber seals. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of booster pumps with stainless steel bodies and impellers, EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure 7.0 bar. Cold water use only. From November 2021 maximum operating temperature 60°C
Range of rim/deck mounted shower handsets with brass bodies (various finishes). The inlet (except for the D5A A02 60A/W model) incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet of the D5A A02 60A/W model incorporates a plastic flow restrictor. The products are supplied with a shower hose and a stainless steel braided EDPM lined flexible hose assembly (for connection prior to the shower hose). Maximum working temperature 60°C.
Range of shower rose outlets (plastic body with various finishes). The inlet incorporates a stainless-steel strainer. Maximum operating temperature 60°C. Open outlet use only.
Range of shower outlets with brass bodies (various finishes) incorporating NBR ‘O’-rings. Maximum operating temperature 60°C.
Range of shower heads and a shower handset. The shower heads have a stainless steel body and ball joint, silicon ‘O’-rings and nozzles, and the inlet incorporates a combined NBR washer and stainless steel filter. The shower handset has a stainless steel body, NBR ‘O’-rings and silicon nozzles. All products incorporate a plastic flow regulator on the inlet. Maximum operating temperature 60°C.
Range of wall mounted or ceiling mounted shower arms with brass bodies (various finishes) Maximum operating temperature 90°C.
Handshower with a chrome plated plastic body. The inlet incorporates a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of wall or ceiling mounted shower arms and a wall mounted shower outlet + holder. The products incorporate a stainless steel bodies (various finishes). Maximum operating temperature 60°C.
Shower arm incorporating a stainless steel body. Maximum operating temperature 85°C.
Dolphin Blue Flexi hose range of wall outlets and brackets incorporating stainless steel bodies (various finishes) and EPDM ‘O’-rings. Maximum operating temperature 85°C
Dolphin Blue range of handheld shower outlets with a stainless bodies (various finishes) and EPDM ‘O’-rings. The inlet incorporates a single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 85°C
Range of shower outlets with brass or stainless steel bodies (chrome plated) fitted with NBR ’O’-rings. Maximum operating temperature 65°C.
Range of shower arms with a brass body and various finishes. Maximum operating temperature 60°C.
Range of Y pattern strainers incorporating blue epoxy coated ductile iron bodies and stainless steel mesh filter. With PN16 flanges to BS EN 1092-2. Maximum working pressure 16.0 bar. Cold water use only.
Range of Y pattern strainers with a bronze body and stainless steel mesh. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
VKF series of flow alarm switches with a plastic body. Maximum working pressure 12.0 bar. Maximum operating temperature 100°C
Range of bib taps with DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Bib tap incorporating brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps (brass, chrome plated brass or DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union tap brass body incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps brass body incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (chrome plated brass) with quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlets incorporate a plastic aerator (AX-IRO-106-CP, AX-MET-106-CP & AX-MET-1369-CP models only) or a plastic flow straightener (AX-IRO-136-CP model only). The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating pressure 60°C.
Pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever or cross top operating members. The spout outlets incorporate a plastic aerator or flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating pressure 60°C.
Range of pillar taps with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headwork with single lever operating members. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of PEX lined rubber hoses with EPDM sealing washers. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower hoses incorporating a PVC inner liner & EPDM washers. Maximum operating temperature 60°C.
Range of chromium plated brass interlocked shower hoses incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of chromium plated brass interlocked shower hoses incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of stainless steel braided or nylon braided EPDM lined hose assemblies available with a variety of end connectors. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
UWILL range of PVC and PEX lined shower hoses (model UW-MS1003 is PEX lined), (models UW-MS1003 and UW-MS1005) incorporate corrugated interlocking metal hoses with various finishes. All hoses incorporate EPDM washers. Maximum operating temperature 65°C.
Range of stainless steel and ACB braided hoses with and EPDM liner and various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC. Hoses with plastic push fittings: maximum working pressure 6.0 bar. Maximum operating temperature 65ºC.
Range of shower hoses incorporating NBR gaskets, either EPDM or PVC liners and stainless steel interlocked casing . Maximum operating temperature 60°C.
Range of “POWERflow” Indirect and direct unvented storage cylinders consisting of factory fitted single or twin coil circuit with either a primary or solar coil. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 4.5 bar at 90˚C and an expansion relief valve set at 3.5 bar. The product is supplied with a pressure reducing valve set at 2.1 bar, expansion vessel, tundish and an approved check assembly (suitable for backflow protection against Fluid Category 2). Primary circuit max working pressure: 3.5 bar Secondary circuit max working pressure: 3.0 bar Solar Coil max working pressure: 3.5 bar Primary and Secondary circuit maximum operating temperature 75.0°C Solar Coil max operating temperature 80.0°C
Wall mounted manually operated, concealed blending valve (brass body) with a ceramic cartridge headwork controlling both flow and temperature with a XXXX operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 90.0 °C
Wall mounted, concealed, manual blending valve with DZR brass body and chrome plated trim set, incorporating a quarter turn ceramic disc headwork controlling the flow and a ceramic cartridge controlling the temperature independently, bothwith dome type operating members. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Manually operated, wall mounted, concealed blending valve (cast brass body) incorporating a ceramic cartridge headwork with a single lever operating member controlling both flow and temperature. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of deck mounted, concealed, manually operated blending valves with brass bodies or stainless-steel bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of wall mounted thermostatic blending valves with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks and single lever operating member. The temperature is controlled independently via a thermostatic cartridge, single lever operating member and a manual override button. Inlets incorporate a strainer and single check valve cartridges however the complete assembly has not been tested to verify it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
‘Ausimix’ compact range of ‘T’-type thermostatic blending valves with nickel plated DZR brass bodies. Each inlet incorporates a stainless-steel strainer and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The SBHEAT110780, SBHEAT110785, HEAT110780 & HEAT110785 models also have angled isolation valves at both inlets. Maximum working pressures and operating temperatures: Existing push fit models: For use with PEX pipe (manufactured to BS7291 part 3) and Polybutylene pipe (manufactured to BS7291 part 2): 12.0 bar, cold water use only. 6.0 bar @ 95°C. For use with copper pipe: Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. Compression models added October 2023: For use with copper pipe to BSEN1057:2006: Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic, shower mixers incorporating brass bodies (various finishes) 2-way ceramic disc diverter headwork to control the flow between two shower outlets with various operating members (see model). The A47203VUK model uses two ‘detent’ (push to on push to off) headworks to control the flow to each outlet. Temperature is controlled independently via a thermostatic cartridge using various operating members (see model) that also incorporates a manual override button. The inlets incorporate a combined EPDM washer and stainless-steel strainer or stainless steel strainer (A47203VUK model) and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlet of the overhead shower incorporates a combined EPDM washer and stainless-steel strainer. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Wall mounted thermostatic blending valve (chromium plated brass) incorporating ceramic disc headwork controlling the flow. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The product is supplied with dome type operating members. The inlets incorporate a stainless steel strainer and single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic shower mixing valves with brass bodies (various finishes - see model) incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a combined NBR washer and stainless-steel strainer, as well as an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Flow control valve incorporating a ceramic cartridge headwork fitted within a chrome plated brass body and a single lever operating member. Product is supplied with a Stainless steel braided PEX lined hose assembly that connects to the outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves with brass bodies (various finishes). Incorporating ceramic disc headwork with a dome type operating member which also divertes the flow between an over head shower and a shower handset. The temperature is controlled independently via a thermostatic cartridge and dome type operating member with a manual override button.The inlets incorporate a single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection) and a filter. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic shower valves, riser rail, shower handset, shower hose and overhead shower outlet. The valve incorporates a brass body (various finishes) and ceramic disc headwork with dome type operating member which controls and diverts the flow between the two shower outlets. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel filters and a single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic bar type shower mixing valves (chromium plated brass). The DC3002 & DC3007 prefix models incorporate a 2-way ceramic disc diverter headwork with dome (DC3001 models) or cubed type (DC3006 & DC3007 models) operating members controlling the flow either shower outlet. The DC3001 model incorporate a ¼ turn ceramic disc headwork with dome (DC3001 & DC3002 models) or cubed type (DC3006 & DC3007 models) operating members controlling the flow to a single shower outlet. The temperature is controlled independently via a thermostatic cartridge. The inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Wall mounted, thermostatic shower blending valves with brass bodies (enclosed within a white and chrome plated case), incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The product also incorporates three ‘detent’ (push to on push to off) diverters, controlling the flow to the shower handset or overhead shower, (which has two outlet patterns). The product is supplied with a shower riser, overhead shower outlet, shower hose and handset. The inlets incorporate a combined EPDM washer and stainless strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Series 900 range of wafer and lugged type, concentric butterfly valves with orange epoxy coated cast iron bodies, austenitic steel discs and EPDM seats. Maximum working pressure 16.0 bar. Cold water use only.
Range of handwheel operated butterfly valves with blue epoxy coated cast iron bodies and discs, with an EPDM seat (D341X-16Q models) or EPDM sealing ring (D343X-16Q models). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer type butterfly valves incorporating blue epoxy coated ductile iron bodies, zinc coated iron discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 100ºC.
Range of wafer type butterfly valves incorporating blue epoxy coated cast iron bodies and stainless steel discs. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of temperature and pressure relief valves incorporating a DZR brass body & EPDM membrane. See model for maximum working pressure. Maximum operating temperature 90°C.
Range of pressure reducing valves with DZR brass bodies (CW602N or CW511L), EPDM ‘O’-rings and a stainless steel strainer. Available with a variety of end connections (see model). Models with compression, pressfit and pushfit connections are for use with copper pipe. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 80°C.
Range of spherical valves withDZR brass bodies and EPDM ‘O’-rings and various operating members (see model). Maximum working pressure 32.0 bar (15mm). Maximum working pressure 25.0 bar (35mm). Maximum operating temperature 85°C.
Quarter turn sanitry ball valve incorporating a brass body and ball, EPDM ‘O’-ring and PTFE seat. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, brass wedges and PTFE packing glands. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of gate valves with blue epoxy resin coated cast iron (DN65-80) or ductile iron (DN100-200) bodies, EPDM coated ductile iron wedge and EPDM gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated cast iron bodies, cast iron disc encapsulated in EPDM, stainless steel shaft and EPDM gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of cold-water inlet control groups with DZR brass bodies consisting of an in-line, adjustable pressure reducing valve (PRV) (adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 or 3.5 bar - see model), strainer and a DZR brass bodied pressure relief valve (SRV) (set at 4.75 bar or 6.0 bar - see model). Products also incorporate an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 16.0 bar. Maximum operating temperature 80°C.
Range of commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with three ¾” x ¾” BSP (F) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet prior to a HDPE inlet hose with ¾” x ¾” captive nut end connections. Maximum working pressure 5.7 Bar. Maximum operating temperature 60°C.
Range of magnetic and electrolytic water conditioners with nickel plated copper bodies. Maximum working pressure 10 bar. MagnaScale2 model has a maximum operating temperature of 85°C. ElectroScale 2 models are for cold water use only.
‘Hostaform® C9021 ECO-B NATURAL, C9021, M15HP, C2521, C13021, C13031, C27021 ECO-B NATURAL, C27021, C52021 & M90JG’. Injection moulded, natural (which appear to be white) acetal materials available in the following colours: Black 14 DW (formerly known as Black 14), White 22, Grey 33, Grey 36, Grey 39, Red 46, Red 47, Yellow 56, Brown 65, Green 76, Blue 87, RAL 2010, RAL 4008 & RAL 5005. Customer specific colours may also be provided with a nomenclature following the structure ‘xx/yyyy DW’ where ‘yyyy’ denotes the specific colour shade, ‘DW’ denotes ‘Drinking Water’ & ‘xx’ denotes 10 – black, 20 - white (incl. Cream, 30 – grey, 40 – red (incl. Pink), 50 – yellow, 60 – brown (incl. Beige), 70 – Green & 80 – blue. For use with water up to 65°C.
'TEPCON® M90 NAT CF2001 & TEPCON® M270 NAT CF2001'. Natural (appears white in colour), injection moulded acetal materials. For use with hot and cold water up to 85°C.
`9011 modified bitumen anticorrosive coating`. Factory applied, black coloured bituminous coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'Electrocoat BP 116'. Factory applied, black coloured bitumen paint. Apply as per manufacturer's technical data sheet, document number 'ECL/TDS/BP116' dated 10th January 2016. Cure for 30 minutes@55°C and then 10 hours@23°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Electroline ES 1212-Black`. Factory applied, black coloured, 2 part epoxy coating. Mix parts A&B in a 3:1 volume ratio. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘SIGMAPRIME 200 for use with SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. SIGMAPRIME 200 (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio. Cure for 3 days@23°C. SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue) is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio. Cure for 12 days@23°C. For use with water up to 23°C.
`R2 Red & R2 Blue`. Factory applied epoxy powder coatings manufactured in Changzhou. Apply as per manufacturer's instructions for use 'ANCZ-RAD-W501', 'revision no: 2' dated 'May. 5th 2021'. Cure for 10 minutes@200°C. For use with water up to 80°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
'Epoxy phenolic FBE-4 RAL 5010'. Factory applied, blue coloured epoxy phenolic coating. Apply as per manufacturer's instructions dated '11/20'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOXY TB BT Grey RAL 7016'. Factory applied, grey coloured, fusion bonded epoxy coating. Apply as per Technical Data Sheet 'document version:1' dated 'June 22, 2021'. Cure for 10 minutes@160°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Karumel EX4412 Blue & Grey’. Factory applied, blue or grey coloured, epoxy resin based powder coating. Apply and cure as per manufacturer’s instructions reference 'PCA-21062901', issued August 2021. For use with water up to 85°C.
`3011 high chlorinated polyethylene anticorrosive coating`. Factory applied, burgundy coloured polyethylene coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per Technical Data Sheet file no. 'TWJ-H-453', edition 'A2', dated '01/03/2020'. Cure for 5 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 Epoxy anticorrosive coating`. Factory applied, black coloured epoxy coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18, 2020. For use with water up to 23°C.
'KINTE Epoxy Resin Coating (ES-BL10724-S9)'. Factory applied, blue coloured coating. Apply and cure as per manufacturer's instructions issued 'March 2018 V5.2'. For use with water up to 85°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
`Jotaguard VA 5001`. Factory applied, dark blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturers test method document no. '39.40.014', issue date '02.01.2018', revision no. '02'. For use with water up to 85°C.
'Jazeera Proofex (formerly known as Jazeera Proof DW)'. Site applied, two-component, grey coloured cementitious coating. Mix Part A (grey coloured powder) with Part B (white, opaque liquid) in a 2:1 mass ratio. Cure for 28 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EZY-PAK™ #100 Packing Compound'. White coloured, PTFE packing compound. Apply as per 'Jet-Lube' TDS for 'EZY-PAK™ #100'. For use with water up to 23°C.
'Extralite Pipe'. Light green/brown coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'Extralite Fitting'. Brown coloured GRP fitting manufactured by hand lay-up. For use with water up to 60°C.
'ajpipe GRP Pipe'. Beige coloured GRP pipe manufactured by continuous filament winding. For use with water up to 23°C. From February 2024, the pipe is for use with water up to 60°C.
'SNB GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
'S-006TG'. Cream coloured, compression moulded GRP panel. For use with water up to 23°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'DAEWOO GRP Panel'. Beige coloured, hot press moulded GRP panel. For use with water up to 50°C.
'XIN-6709-01 hose' manufactured from 'GR-PVC 001N' raw material. Single layered, extruded, black coloured PVC hose. For use with water up to 85°C.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A502PS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite® A860S'. White coloured ion exchange resin. For use with water up to 23°C.
'C107DQ (Na), C108DQ (Na) & C110DQ (Na)'. Light yellow coloured ion exchange resins. For use with water up to 23°C.
`Griffon P-20` Lubricant. White coloured lubricant in the form of a paste. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'IKV Tribostar STF 2501 & Addisil WTG 1'. Translucent, white coloured silicone greases. Apply as per manufacturer's instructions. For use with water up to 85°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Ultradur® B4300 G6 HR FC Aqua grey 35413 '. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'Sirester EC 0994/AT/V/15'. Pale green coloured orthothalic resin manufactured by hand lay-up. For use with water up to 23°C.
`Polygel-2132`. Yellow coloured, contact moulded Gelcoat. For use with water up to 50°C.
'100 US Gallon Dubai Polytank Panel'. Triple layered, rotationally moulded LLDPE tank panel comprising of a white coloured inner layer, black coloured middle layer and white coloured outer layer. For use with water up to 65°C.
'Radius Systems Socket Fittings and Saddle Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 60°C.
'Revolve 6402U'. White coloured (translucent), polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'PE-BWG'. Transparent, extruded, single layer, polyethylene hose. In July 2023, 'PE-BWG Black', a black coloured (opaque), extruded, single layer, polyethylene hose was added to the approval. For use with water up to 85°C.
'BKBB-660'. Black coloured LLDPE 'buoyant body' manufactured by rotational moulding. For use with water up to 23°C.
'XSPE-GPE01'. Black coloured (with blue stripes), extruded polyethylene pipe. For use with water up to 23°C.
'Hostalen GM 5010 T3 Black'. Black coloured, extruded HDPE material. For use with water up to 23°C.
'HD 8570.29'. Natural (appears white with black specks), high density polyethylene resin material manufactured by rotational moulding. For use with water up to 85°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Durafide® 1130A1T WF900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WF9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'DIC. PPS FZ-2140 BLACK'. 'DIC.PPS FZ-2140 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'DSA Pipe'. Grey coloured extruded PPR pipe. For use with water up to 70°C.
'DSB Fitting'. Grey coloured, injection moulded PPR fittings. For use with water up to 70°C.
'XSPPR-EAC01'. Grey coloured, extruded polypropylene pipe. For use with water up to 85°C.
`Polyfill PPC GF2007 PD1 yellow`. Yellow coloured, injection moulded polypropylene material. For use with water up to 23°C.
'ISOFIL HK 40 5FH0 WT0580'. White coloured (opaque), injection moulded PP material. For use with water up to 85°C.
'ISOFIL H 40 C2 F NA1'. Grey coloured (opaque), injection moulded polypropylene material. For use with water up to 85°C.
'Ultrason® S3010 Natural'. Natural (beige coloured), injection moulded polysulphone material. For use with water up to 85°C.
'Ultrason® S2010 Natural'. Natural (colourless), injection moulded polysulphone material. For use with water up to 85°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JP EB 750'. Black coloured ebonite rubber manufactured by calendaring. Shore hardness 75 D. Tested in-radius size 1.03mm. For use with water up to 23°C.
'EP6008'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.8mm. For use with water up to 85°C.
`EP2/9/10 BLK 'O' rings`. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
`EP11/01/13 BLK 'O' rings & seals`. Black coloured, injection moulded 'O' rings & seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.8mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
'E70N01C 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have an in-radius size of 0.5mm. The gaskets have an in-radius size of 1.0mm. For use with water up to 85°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'OYRTEP7011PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 65°C.
'ZF-73'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘EW45, EW50, EW53, EW54, EW54W, EW55, EW60, EW65, EW70, EW75, EW80, EW81 & EW85’. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 45 & 85. Tested in-radius size 1.4mm. For use with water up to 60°C.
'REGM20'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'MV250 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'THERMOLAST K TF5WHA, TF6WHB, TF6WHA, TF7WHB, TF7WHA, TF8WHB & TF8WHA'. Injection moulded, natural (appears off-white translucent) TPE materials with a shore hardness of between 55 and 85. Tested in-radius size 1.0mm. The materials may be coloured using one, or any combination of, the following Kraiburg pigments (up to and including the maximum level included): Black (maximum level 3%). White (maximum level 2%). Blue (maximum level 2%). Orange (maximum level 2%). Yellow 1 (maximum level 2%). Yellow 2 (maximum level 2%). Yellow 3 (maximum level 2%). Green (maximum level 2%). Red 1 (maximum level 2%). Red 2 (maximum level 2%). Brown (maximum level 2%). For use with water up to 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The product is supplied with a stainless-steel braided EPDM lined flexible hose assembly for installation between the solenoid valve and the tap body. The spout outlet incorporates a plastic aerator with built in flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of BS1212-4 diaphragm type inlet valves incorporating a plastic body for use in either side or bottom entry WC cisterns. The valves incorporate an up and over discharge, plastic arm and float. The inlet is fitted with a plastic flow regulator and strainer. Maximum working pressure 10 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Bottom Entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. Incorporates plastic body and ½’’ BSP inlet. The inlet incorporates a plastic strainer and flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The cistern incorporates an angled servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Single hole bidet tap with brass body (various finishes) fixed spout outlet and a ceramic disc headwork (various operating members). The outlet incorporates an aerator and the product is supplied with a pop-up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The product is supplied with metal backnuts. UK-1DPXX models only are a single feed and come with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole or two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPM-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPM-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPM-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPM-6DLN-00 & UMPM-7DLN- 00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole or two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPK-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPK-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPK-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPK-6DLN-00 & UMPK-7DLN-00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole (UMPU-1DLN-00 & UMPU-2DLN-00 models) or two hole (UMPU-6DLN-00 & UMPU-7DLN-00 models), single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating one (UMPU-1DLN-00 model only) or two quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The UMPU-1DLN-00 model is a single feed and comes with an optional ½” NPSM (M) x ½” BSP (F) brass adapter. The UMPU-2DLN-00 model is supplied with two ½” BSP (F) x ½” BSP (M) single check assemblies (suitable for backflow protection against Fluid category 2), for installation on each inlet hose. The inlets on the UMPU-6DLN-00 & UMPU-7DLN-00 models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disk headwork with a single lever operating member. The product incorporates a hand held pre-rinse spray with a self-closing trigger on a flexible hose within an overhead spring. Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disk headworks with single lever operating members. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn ceramic disk headwork with a single lever operating member. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with plastic backnuts. Maximum working pressure 8.62 bar. Maximum operating temperature 60°C.
Single-hole single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a pull-out spray. The pull-out spray hose is stainless steel braided and has a. The pull-out spray outlet incorporates a button which changes and/or stops the flow of water, a plastic aerator and check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection.
Range of single hole, single outlet (swivel) pull down spray combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The connection between the body and the spout incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet incorporates a plastic aerator. The products are supplied with optional ½” BSP (F) x ⅜ BSP (M) brass adaptors and NBR washers for installation on each inlet hose. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating ceramic a cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly with a brushed stainless-steel body, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with click type or pop-up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 110 000 model is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The products are supplied with a brass ⅜” BSP (M) x 15mm compression adapter. The spout outlets incorporate a plastic aerator. The A6259AA model is supplied with pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The HV3 model is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65 °C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating a ceramic cartridge headwork and single lever operating members however model 922034 is fitted with a non rising spindle headwork and dome type operating members. The spout outlet incorporates a plastic flow straightener on models: 922064, 922034, 922302, 922303, 922304 or flow straightener and aerator kit on models: 922311, 922312, 922313, and some models are supplied with a click waste. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with either single lever or cross top operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) also with end swivel spout, combination tap assembly (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) also with end swivel spout, combination tap assembly (brass or stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) combination tap assemblies (brass body - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The VOLA KV6 and VOLA KV7 models also have an end swivel spout. The VOLA HV7 and VOLA KV7 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk head works with cross top operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disk headworks with cross top operating members. The spout outlet incorporates either a plastic aerator or a flow straighter. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass or stainless steel - INOX models), comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a dome type or single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. The products are supplied with click type (click clack) waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with plastic back nuts. Maximum working pressure 5.0 bar. Maximum working temperature 60°C. A two hole single outlet (fixed) combination tap assembly with brass body (chromium plated). Incorporating a quarter turn ceramic disc headworks with a single lever operating member. The outlet incorporates a plastic flow straightener. This product is supplied with plastic back nuts. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed rough in set with a brass body and a variety of separate trim sets incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a 2 way ceramic disc diverter controlling the flow between the spout outlet and the shower outlets with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The product incorporates a secondary manual diverter to divert the flow between the overhead shower and the shower hose and handset. The spout outlet incorporates a plastic aerator. The inlets and the outlet to the shower handset all incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet fixed combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 70°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a manual diverter to shower with a single lever operating member. Flow is controlled via a ½ turn ceramic disc headworks with cross top operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating member and a manual diverter to the shower outlet. The products are supplied with a shower hose and handset. The spout outlet incorporates a plastic aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
A two-hole single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with a shower hose and handset and either plastic or metal back nuts. Maximum working pressure 10.0 bar. Maximum working temperature 65°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a manual diverter to shower with a single lever operating member. Flow is controlled via a ½ turn ceramic disc headworks with cross top operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC
Two-hole single outlet fixed combination tap assemblies incorporating a brass body (variety of finishes), quarter turn ceramic disc headwork with single lever operating members and manual diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with a cross-top operating member. The products are supplied with a flow regulator, shower handset, shower hose and shower head. The spout outlets incorporate a plastic aerator. The inlets of the tap and the outlet of the shower handset incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, exposed, two-hole single outlet, fixed, combination tap assemblies (brass body – various finishes) incorporating two ‘detent’ (push to on push to off) headworks, one controlling the flow to the bath outlet and the other to the shower outlet. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. Both inlets and the shower outlet incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets also incorporate a stainless-steel strainer. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with various operating members (see model). The spout outlets of the SH-T80541 & SH-T80542 models incorporate a plastic flow straightener, all other models incorporate a plastic aerator. The products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating quarter turn ceramic disc headworks with either single lever or wheel operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet (swivel) combination tap assemblies incorporating brass bodies (various finishes) and quarter turn ceramic disc headwork with either single lever or cross top operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two-hole, single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Two-hole, single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Two-hole, single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members and a locakble self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic aerator. The product is supplied with a shower hose and handset and metal backnuts Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of wall mounted three hole, single outlet (fixed) combination tap assemblies with brass bodies (in various finishes). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with various operating members (see model). The products are supplied with stainless steel braided EDPM lined flexible hose assemblies incorporating ¾” captive nut end connections for installation between the headworks and the spout. The spout outlet incorporates either a plastic flow straightener or plastic aerator (see model). The invincible range is supplied with a plastic back nut, all other models are supplied with metal back nuts. Maximum working pressure 3.0 bar. Maximum working temperature 60°C.
Three hole, single outlet (fixed) combination tap assembly with a brass body (various finishes - see model), incorporating quarter turn ceramic disc headworks with dome type operating members. The products are supplied with stainless steel braided EDPM lined flexible hose assemblies incorporating ¾” captive nut end connections for installation between the headworks and the spout. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 3.0 bar. Maximum working temperature 60°C.
Range of wall mounted three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating quarter turn ceramic disc headwork with either single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever (20815882 model) or cross top (20815892 model) operating members. The product is supplied with stainless steel braided PEX lined flexible hose assemblies for installation between the side valves and the spout. The spout outlets incorporate a plastic aerator. The side valves are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Functional trim set (chrome plated), comprising of a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout incorporates a plastic flow regulator on the inlet and a plastic aerator on the outlet. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Functional trim set (chrome plated), comprising two quarter turn ceramic disc headworks with either single lever (models ending in 882) or cross top (models ending in 892) operating members and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Bath spout outlet with a brass body (various finishes) and a plastic aerator. Maximum operating temperature 60°C.
Range of deck mounted spout outlets (chrome plated brass). The spout incorporates a plastic flow regulator on the inlet and a plastic aerator on the outlet. Maximum working temperature 60°C.
Range of wall mounted basin spouts (chromium plated brass). The spout incorporates a plastic flow regulator on the inlet and a plastic aerator on the outlet. Maximum operating temperature 60°C.
Range of expansion vessels incorporating composite plastic bodies and butyl diaphragms. Maximum working pressure 8.6 bar. Cold water use only.
Range of SUS316L & SUS304 stainless steel press fittings for use with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press fit fittings incorporating copper (GP5 models) or bronze (GP4 models) bodies and EPDM `O`-rings, for use with copper tube to EN 1057. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of WC dual flush drop valve comprising of a plastic body, silicone seating washer and an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of WC dual flush drop valves comprising of a plastic body, silicone seal and an internal overflow. The valve is operated via a push button or lever assembly for either full or reduced flush. Cold water use only.
Range of handwheel operated hemisphere valves with blue epoxy coated ductile iron bodies, stainless-steel disc, seat and stems, and EDPM seals Maximum working pressure 10.0 bar. Maximum working temperature 80°C.
‘E-WATER BLOCK’ self-closing valves with black plastic bodies and stainless-steel filters. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Copper corrugated hose. Maximum working pressure 10.0 bar. Maximum working temperature 90°C.
Range of plastic bodied quarter turn isolation valves, with EPDM rubber ‘O’-rings, seals and washers. The 52.009.100 model is operated by a hex key (not supplied), the 52.009.200 model is operated by a key (supplied). Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Appliance inlet group assembly comprising of EPDM gaskets, a plastic bodied Y-pattern strainer, ¾” BSP (F) x ½” BSP (F) brass adaptor, a chrome plated DZR brass bodied double check valve assembly (suitable for backflow protection against Fluid Categry3), a ½” BSP (F) x ¾” BSP (M) brass adaptor, a dual layer hose with a PVC outer (grey) and PVC liner (black), a solenoid valve which incorporates a plastic strainer and a flow regulator within the inlet. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of water meter couplings with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only
Appliance inlet group assembly comprising of an EPDM gasket, ¾” BSP (F) x ½” BSP (F) brass adaptor, a chrome plated DZR brass bodied double check valve assembly (suitable for backflow protection against Fluid Categry3), a ½” BSP (F) x ¾” BSP (M) brass adaptor, a flexible reinforced hose assembly with a PVC lining and a solenoid valve which incorporates a plastic strainer and a flow regulator within the inlet. Maximum working pressure 5.0 bar. Cold water use only.
Range of hand wash and dryer units The flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a non-verifiable double check valve assembly (suitable for backflow protection against Fluid category 3) for installation on the inlet. The double check valve assembly also incorporates a drain port, (located in between the cartridges), and an integral spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 50ºC.
Pressure gauge with a plastic case, brass connector and bronze spring tube. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of booster pumps with stainless steel bodies and impellers (AISI 304: AL-RED models or AISI 316: CP models), EPDM ‘O’-rings and a ceramic/graphite/EPDM shaft seal. Maximum working pressure: CP(m) 100-130-132-150-158 and AL-RED(m) 600-610-620 models: 6.0 bar. All other models: 8.0 bar. Maximum operating temperature 90°C.
Centrifugal pump with a plastic body, plastic impellers and NBR ‘O’-rings. The product includes an (integral) expansion vessel and the inlet incorporates a non-return valve (not suitable for backflow protection). Maximum working pressure 4.5 bar. Maximum operating temperature 50°C.
Single pump units with plastic bodies and impellers, EPDM ‘O’-rings, expansion vessel with an EPDM membrane and a carbon graphite/ceramic/NBR shaft seal (bt-ar 13 bx 4ff xp). Each pump inlet incorporates a non-return valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of shower handsets with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 65°C.
Range of wall mounted compact shower panels with push button timed flow control. The inlet incorporates a plastic flow regulator and a stainless-steel strainer. Maximum working pressure 4.0 Bar Maximum operating temperature 60°C
Concealed installation set for use with wall mounted overhead shower outlets (brass body – various finishes). The inlet to the shower outlet incorporates a stainless-steel strainer, a plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of shower arms and outlets with chrome plated brass bodies. The shower outlets incorporate plastic flow regulators at the inlets. Maximum operating temperature 85°C.
Range of shower hoses and handsets (various finishes - see model) with EPDM ‘O’-rings. Maximum operating temperature 60°C.
Range of Y pattern strainers with a bronze body and stainless steel mesh. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Pillar tap incorporating a ceramic cartridge headwork (chrome plated brass body) with a single lever operating member. The spout outlet incorporates a flow straightener and flow regulator. The product is supplied with plastic backnuts Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of pillar taps with brass bodies (various finishes - see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The 4102BD18 models incorporate a plastic flow restrictor on the inlet. The products are supplied with plastic and brass backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with either cross top or single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of self-closing tap assemblies (chrome plated brass) with spring loaded headworks and dome type or single lever (745440 model only) operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted, self-closing tap assemblies (chrome plated brass) with spring loaded headwork and dome type operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Self-closing tap for drinking water fountains (chromium plated brass) with dome type operating member. The spout outlet incorporates a stainless-steel strainer. The product is supplied with a metal back nut. Maximum working pressure 5.0 bar. Cold water use only.
Range of self-closing taps (chromium plated brass) incorporating spring loaded headworks with dome type operating members. The spout outlet of the 9000 model incorporates a plastic flow straightener. The products are supplied with a metal back nut. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C, except for the 9054SA model which is cold water use only.
Self-closing drinking fountain tap (chromium plated brass) with non-concussive headwork operated via a push button. The tap incorporates a metal shroud and is supplied with a metal back nut. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel interlocked shower hoses (various finishes) incorporating a PVC liner and EPDM gaskets. Maximum operating temperature 65°C.
Multi-layer hose incorporating a PVC inner layer and EPDM ‘O’-rings. Maximum operating temperature is 65°C.
Mitsubishi Electric ‘EHPT20Q – VM2EA’ stainless steel unvented primary thermal store cylinder unit. An inline booster heater is also fitted into the primary circuit. The cylinder is fitted with two pressure relief valves set at 3.0 bar. Heat is transferred from the stored primary water to the secondary water circuit via a plate heat exchanger which provides instantaneous hot water. The primary thermal storage cylinder is to be filled by the use of the supplied temporary filling loop assembly, which consistd of a stainless steel braided EPDM lined flexible hose, a lever operated brass spherical valve and a DZR brass double check valve assembly (suitable for backflow protection against Fluid Category 3) that incorporates a lever operated spherical valve. A primary expansion vessel is supplied to accommodate the expansion of the primary water when heated. An automatic air vent is fitted to the top of the thermal store. The product is supplied with a tundish. Maximum working pressure: Primary circuit 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature: Primary circuit 72°C, Secondary circuit 70°C.
SSB, SSI SST range of stainless steel unvented cylinders provided with an unvented kit supplied with cylinders containing a temperature and pressure reducing valve set at 3.0 bar and an expansion vessel and single check valve (suitable for fluid category 2) . Available as storage tank, indirect or twin coil. Maximum working pressure of the cylinder 6.0 bar, maximum working pressure of the coil or coils 12.0 bar. Maximum operating temperature 95°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Wall mounted, exposed thermostatic shower valve (chromium plated brass) incorporating a thermostatic cartridge that controls the temperature and a shut off valve that controls the flow both with a single lever operating member. The inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Wall mounted, bar type, thermostatic shower mixer (chromium plated brass), incorporating a ½ turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The TR10032CP model is supplied with a riser rail, shower hose and handset. The TR10010CP is the valve only. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic bar type shower mixing valves (chromium plated brass). The B36264 model incorporates a 2-way ceramic disc diverter headwork with a dome type operating member controlling the flow between an overhead shower outlet and a shower handset. The B38130 model incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the flow to a shower handset. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Both products are supplied with a shower hose and handset, the B36264 model also includes a shower riser to an overhead shower outlet. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic shower blending valves (chromium plated brass) with one or two outlets (see model). Flow is controlled by one or two quarter turn ceramic disc headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a.cross top operating member. Each inlet incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, concealed, thermostatic shower blending valves with brass bodies and trim sets (various finishes). The temperature is controlled via a thermostatic cartridge with a cross top or single lever operating member. The inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, bar type thermostatic shower mixers (chromium plated brass) with a 2-way ceramic disc diverter controlling the flow to either shower outlet. Temperature is controlled independently via a thermostatic cartridge which incorporates a manual override button. The S06 model has dome type operating members and the S15-2 model has cube type operating members. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, concealed, thermostatic mixing vales with brass bodies and chrome plated trim sets, incorporating one or two quarter turn ceramic disc headworks with various operating members (see models). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of water filters cartridges with plastic bodies and either carbon block or activated carbon filter media. Maximum working pressure 8.6 bar. Maximum operating temperature 38°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, EPDM seat and a stainless steel disc. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated butterfly valves incorporating blue epoxy coated cast iron bodies and discs, and EPDM seats. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of wafer and lugged type, concentric butterfly valves with epoxy coated cast iron bodies, austenitic steel discs and EPDM seats. Maximum working pressure 16.0 bar. Cold water use only.
Range of shower bars with brass bodies (various finishes), incorporating a manual diverter with cube or dome type operating members, which diverts between an overhead shower and a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, rough in sets with brass bodies. The product is supplied with a separate trim set incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pressure relief valves pre-set @ 6.0 bar, incorporating DZR brass bodies, EPDM seal cup and EPDM ‘O’-ring. Maximum operating temperature 99˚C
Range of lever operating spherical valves incorporating brass bodies, chrome plated brass ball, PTFE seals and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of angled servicing valves with brushed chrome plated DZR brass bodies and ball.The product incorporates a stainless steel strainer and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of angled isolation valves with brass bodies (brushed chrome plated), for use with copper tube manufactured to EN1057. The inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of gate valves incorporating brass bodies and wedges with EPDM ‘O’-rings and a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated ductile iron disc and EPDM seals. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of 115 gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of globe stop valves with a bronze body and disc holder, DZR brass stem and stem ring, PTFE stem gasket and disc. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum operating pressure 20.0 bar. Maximum operating temperature 85°C.
Range of commercial dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of commercial dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of water conditioners incorporating a static PTFE and zinc anode in a brass or nickel plated bronze body. Between November 2021 and December 2023 the maximum working pressure is: ET/ETD models = 10.0bar, EF/EF-16 models = 16.0 bar, EF-40 models = 40.0 bar. From January 2024 the maximum working pressure is: ET/ETD/EF/EF-16 models = 16.0 bar & EF-40 models = 40.0 bar. Maximum operating temperature 60°C.
Hostaform®, injection moulded POM materials. For use with water up to 85°C: Hostaform® Special Grade: M25AE 10-2013 & M25AE 10-2013 ECO-B (black coloured). Hostaform® Glass Bead Filled Grade: C9021 GV3/30 NATURAL. Hostaform® M30RS Natural & M30RS ECO-B NATURAL. For use with water up to 65°C: Hostaform® Unfilled Grades: T1020 NATURAL. Hostaform® Glass Fibre Filled Grades: C9021 GV1/10 NATURAL, C9021 GV1/20 NATURAL, C9021 GV1/30 NATURAL, C9021 GV1/30 3134 NATURAL & C9021 GV1/30 3134 ECO-B NATURAL. Hostaform® Glass Bead Filled Grades: C9021 GV3/10 NATURAL & C9021 GV3/20 NATURAL. Hostaform® Special Grades: M25IE natural, M25IE ECO-B NATURAL & M30AE. Between April 2021 and 2nd August 2022, these grades were for use with water up to 65°C. Between 3rd August 2022 and 30th April 2026, these grades are for use with water up to 85°C: Hostaform® Unfilled Grades: M15HP NATURAL, M15HP ECO-B NATURAL, C2521 NATURAL, C2521 ECO-B NATURAL, C9021, C9021 ECO-B NATURAL, C 9021 ECO-C 872 NATURAL, C13021 NATURAL, C13021 ECO-B NATURAL, C 13021 ECO-C 872 NATURAL, C13031 NATURAL, C13031 ECO-B NATURAL, C 13031 ECO-C 872 NATURAL, C27021 NATURAL, C27021 ECO-B NATURAL & C 27021 ECO-C 872 NATURAL. Hostaform® Lubricated Grades: C9021 M (Natural colour is grey), C9021 M ECO-B NATURAL, C9021 FCT1 NATURAL, C9021 FCT1 ECO-B NATURAL, C9021 TF NATURAL, C9021 TF ECO-B NATURAL, C9021 K NATURAL, C9021 K ECO-B NATURAL, C13021RM NATURAL & C13021RM ECO-B NATURAL. Hostaform® Special Grade: MR130ACS NATURAL & MR130ACS ECO-B NATURAL. These grades were added January 2022. Between January 2022 and 2nd August 2022, these grades were for use with water up to 65°C. Between 3rd August 2022 and 30th April 2026, these grades are for use with water up to 85°C: Tarnoform® 200 CE natural, 300 CE natural, 400 CE natural, 411 CE natural & 500 CE natural. Between April 2021 and xx February 2023, these grades were for use with water up to 65°C. Between 16th February 2023 and 30th April 2026, these grades are for use with water up to 85°C: Hostaform® Unfilled Grades: C 52021 NATURAL & C 52021 ECO-B NATURAL. Tarnoform® 700 CE. Hostaform® Special Grades: C13031 XAS-G NATURAL, C13031 XAS-G ECO-B NATURAL, M25AE NATURAL, M25AE ECO-B NATURAL & HF M25AE ECO-C 872 NATURAL. For use with water up to 65°C: Grade added February 2023: Hostaform® M25AE 10/5358 DW. Grade added April 2025: Hostaform® MR130 ACS 10/5358 DW Black. For use with water up to 85°C: Grade added April 2025: Hostaform® M25AE 10/5358 DW black.
'KEPITAL F20-03 BKM'. Black coloured, injection moulded POM material. For use with water up to 85°C.
`POWLAC EY161`. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions `no. CKP-2015-0172`. Cure for 5 minutes@180°C. For use with water up to 85°C. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Global Smart (INSUPIPE)'. Factory applied, grey coloured cement. Mix cement:sand:water in a 30:55:15 ratio. Cure for 48 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'QuickSpray Industrial W coating for use with Quick Prime primer'. Factory applied, blue coloured coating system comprising of a primer and topcoat. ‘Quick Prime’ is a two-component epoxy primer. Mix parts A & B in a 1:2 volume ratio and cure for 4 hours@20°C. ‘QuickSpray Industrial W’ is a two-component elastomeric topcoat. Mix parts A & B in a 1:1 volume ratio, apply over the primer and then cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 801 Blue 502'. Factory applied, grey coloured modified PE blend coating. Pre-heat part/item to be coated to 340°C, dip into a fluidized bed containing the coating and then allow to cool at room temperature. No cure required For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nu Vista'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours at 45°C and then 28 days (672 hours)@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Infra Pro'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours@45°C and then 28 days (672 hours) @35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-111'. Blue coloured, factory applied epoxy powder coating. Apply and cure as per manufacturer's instructions XL-R-019-R1 dated 2015-11-12'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'ColorDur T300 EPOXY SF Coating - Red' & 'ColorDur T300 EPOXY SF Coating - Grey' (grey was added to approval in August 2022). Factory applied, two-component, red or grey coloured epoxy coating. Mix resin and hardener in a 3:1 volume ratio. Cured for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'KD-002'. Factory applied, blue coloured powder coating. Apply and cure as per manufacturer's instructions file number 'KD-1230-20', version 'A0', dated '2020-12-30'. For use with water up to 23°C.
'SC2 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-002 issue 1' dated 09-08-2016. For use with water up to 85°C.
'Hempaline Defend 630 Cure 72'. Factory applied, white coloured, two-component epoxy coating. Mix base and curing agent in a 3:1 volume ratio and apply as per manufacturer's product data sheets dated June 2021, Cure for 6 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'Rilsan (MagnaCoat 5501 F)'. Factory applied, white coloured (opaque), polyamide powder coating. Apply as per manufacturer's instructions dated 02/01/2018. Cure for 10 minutes@230°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FIBER TECH 80, Low VOC fiberglass resin'. Factory applied, brown coloured polyester resin & fibreglass. Apply as per manufacturer's method statement reference 'PP-GRP-092021-R1' dated '21 Sept. 2020'. Cure for 48 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC1 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-001 issue 1' dated 09-08-2016. For use with water up to 85°C.
"Bond-It Tanking Slurry". Site applied, grey coloured, two part (powder & water) cementitious waterproof coating. Mix and apply as per manufacturer`s instructions 'Version 9' dated 06/08/20. Cure for 12 days at 7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`DR-PNL-WT Tank Panel`. Grey coloured GRP panel manufactured by hydraulic press moulding. For use with water up to 50°C.
`HYUNDAE Tank Panel`. Grey coloured GRP panel manufactured by hydraulic press moulding. For use with water up to 50°C.
`Polyver-3345`. Orange/brown coloured, contact moulded vinyl ester resin material. For use with water up to 50°C.
`Polyver-3045`. Brown coloured, contact moulded vinyl ester resin material. For use with water up to 50°C.
'568H+L101'. Natural (appears off-white in colour), injection moulded GRP material. For use with water up to 70°C.
`8601-A`. Extruded, dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. Shore hardness 85. For use with water up to 85°C.
'Plustek PA303G6BK16'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'TYPLEX-1055'. Grey coloured, extruded Polybutylene-1 material. For use with water up to 85°C.
'POLYISO 200 NA'. Amber coloured (transparent), contact moulded polyester material. For use with water up to 50°C.
'Shield MDPE Fitting'. Black coloured, injection moulded PE80 fitting. For use with water up to 85°C.
'Shield MDPE Pipe'. Black coloured, extruded PE80 pipe. For use with water up to 85°C.
'SP-01 HDPE Fitting'. Black coloured, injection moulded HDPE fittings. For use with water up to 23°C.
'Hostalen CRP100 Black & Hostalen CRP100 RESIST CR Black'. Black coloured HDPE materials, manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Helisystem CT fitting'. Green coloured, injection moulded PP-RCT fitting. Between July 2021 and September 2022, the fitting was for use with water up to 23°C. Between October 2022 and July 2026, the fitting is for use with water up to 75°C.
'RTP 499 X 129130 A Natural & RTP 499 X 136502 Natural'. Natural (appear grey in colour), injection moulded polystyrene materials. For use with water up to 50°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP7008S 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 60°C.
'EP1/1/6 BLK' O-rings. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.75mm. For use with water up to 85°C.
'EP906'. Black coloured, extruded EPDM washer. Shore hardness 90. Tested in-radius size 1.4mm. For use with water up to 85°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
'CEW50, CEW55, CEW60, CEW65, CEW70, CEW75, CEW80, CEW85 & CEW88'. Black coloured, transfer moulded EPDM rubber materials. Shore hardness between 50 & 88. Tested in-radius size 1.15mm. For use with water up to 60°C.
'CVE45, CVE48, CVE50, CVE52, CVE55, CVE60, CVE61, CVE65, CVE69, CVE70, CVE75, CVE78 & CVE80'. Black coloured, extruded, EPDM materials. Shore hardness between 45 & 80. Tested in-radius size 1.5mm. For use with water up to 60°C.
'AquaFlex T 5817'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 65°C.
'RVK EPDM EP 210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'E0265'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. Between September 2021 and 3rd August 2022, the material was for use with water up to 23°C. Between 4th August 2022 and September 2026, the material is for use with water up to 50°C
'PERTEC UP FKM 70.501-07'. Black coloured, injection moulded FKM material. Shore hardness 70. Tested in-radius size 1.01mm. For use with water up to 85°C.
'7400 D-ring gasket'. Red/brown coloured, compression moulded, silicone rubber D-ring gasket. Shore hardness 45. Tested in-radius size 0.70mm. For use with water up to 23°C.
'Uneplas Gel Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions review date '2019-09-11'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of float operated valves with brass bodies manufactured to BS1212 Part 2 1990. The valves have ½’’ BSP inlets with plastic backnuts, brass or plastic back plates, an up and over type outlet discharge and a brass lever arm. Maximum working pressure 14.0 bar. For use with cold water only.
Range of float operated valves with plastic bodies and either brass or plastic inlet tails of the side or bottom entry type manufactured to BS1212 Part 3 1990. The valves have ½’’ BSP inlets with plastic backnuts, an up and over type outlet discharge and a plastic operating lever adjusted by a screw & lock nut. Maximum working pressure 14.0 bar. For cold water use only.
Range of BS1212 Part 3 1990 float operated valves incorporating plastic bodies of either the side or bottom entry type. Maximum working pressure 14.0 bar. For cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. There is a flow restrictor and stainless-steel strainer on the inlet valve. The cistern is operated by a manual push button. Maximum operating pressure 8.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout has a waterfall outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Type ‘AB’ air gap assembly (verified by test - suitable for backflow protection against Fluid Category 5) with flow controlled via a solenoid valve. Supplied with EPDM inlet hoses that incorporate a single check valve cartridge, however the check valve has not been fully tested to demonstrate it provides backflow protection. Max working pressure 6.0 bar. Maximum operating temperature 60ºC.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of in-line, non-verifiable single check valve assemblies consisting of a spring loaded, resilient trim, single check valve cartridge housed within a DZR brass body (brass or chrome plated). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-verifiable double check valve assemblies with DZR brass bodies (chrome plated), incorporating two spring loaded, resilient trim in-line check valve cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of inline non verifiable double check valve assemblies with DZR brass bodies. Model S0270L-1 incorporates an isolation valve and is chrome plated. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
‘Calomax Eclipse’ range of electrically heated counter top or wall mounted catering water boilers. The boilers incorporate a stainless steel cold water feed cistern which has a combined vent/overflow fitted with an insect screen. The water to the cistern is supplied via a solenoid valve which incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The water level is electronically controlled via level sensors. The water is dispensed via a manually operated brass bodied (chrome plated)/stainless steel bodied self-closing tap(s) or a push button controlling a solenoid valve prior to the outlet. The counter top models are supplied with a PVC coated flexible inlet hose (¾” BSP (F) x 15mm standpipe) and a push fit adaptor (15mm push fit x ¾ BSP (F)). Maximum working pressure 10.0 bar (to the solenoid valve). Maximum temperature of dispsensed water 90°C for PB3C10 & PB3W5 models and 97°C for all other models. Cold water supply only.
Range of fittings for use with cisterns storing wholesome water. Consisting of screened tank overflows, a screened tank breather, two-way expansion pipe tee piece, tank lid adaptor and tank connections. Where products are screened they comprise of a stainless steel mesh. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed spout with a swivel nozzle) over the rim bidet combination tap assemblies (various finishes). The taps incorporate quarter turn ceramic disc headwork with cross top or lever type operating members. The spout outlets have a plastic aerator and the products are supplied with a lever type pop-up waste. Maximum working pressure 5.0 bar Maximum operating temperature 60°C
Aerator with a plastic body, brass housing and EPDM washer. Maximum operating temperature 85°C.
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Headwork assemblies (stainless steel or brass bodies) incorporating a quarter turn ceramic disc with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies and EDPM ‘O’-rings and gaskets. The products are intended for insertion into specifically dimensioned tap bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating members and pull-down spray handset. The spout outlet incorporates a plastic aerator. The product is supplied with a metal backnut. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating chromium plated brass bodies, ceramic cartridge headwork with single lever operating member. The spout outlets incorporate either a plastic aerator or flow straightener. The 2565T1EP, 2565T3EP & 3565T5EP models are supplied with a check valve cartridge and filter on the inlets, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The 2565T1, 2565T3 & 2565T5 models have flow restrictors on the inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating a ceramic cartridge headwork and either cross top or a single lever operating member. The spout outlets incorporate a plastic flow straightener and the products are supplied with lever operated pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes, see models) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied with either a lever type waste (model 39 034) or screw down waste (39 037). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass) incorporating a ceramic cartridge headworks with single lever operating member. The spout outlets incorporate a plastic aerator. Model (PM BAS C) is supplied with a lever type pop-up waste. Maximum operating pressure 7.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headworks, and various operating members. The spout outlet incorporates a flow straightener and is also supplied with an optional aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks, and various operating members. The spout outlet incorporates a flow straightener. Product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with optional ⅜” BSP (M) x ½” BSP (F) adaptors each with a fibre gasket for installation on each inlet hose. The product is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet deck mounted (fixed) combination tap assembly with soap dispenser and hand dryer appliances operated via an infra-red sensor. This product incorporates a solenoid valve and plastic flow restrictor. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass body with various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with a pop up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet wall mounted (fixed) combination tap assembly with soap dispenser and hand dryer appliances operated via an infra-red sensor. This product incorporates a solenoid valve and plastic flow restrictor. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener. The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating ceramic a cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever operated pop-up waste or click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly with brass body (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet (activated by pulling the end of the spout surround). The shower outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The product is also supplied with shower hose and shower handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disc headworks with cross-top operating members. The inlet hose assemblies incorporate a servicing valve and is supplied with a single check valve assembly verified by test (suitable for backflow protection against Fluid Category 2). The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headwork with cross-top operating members. The inlet hose assemblies incorporate a servicing valve and is supplied with a single check valve assembly verified by test (suitable for backflow protection against Fluid Category 2). The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes).Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a flow straightener and is supplied with an optional plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (chrome plated) brass bodies. Incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a aerator. Inlets incorporate single check valve cartridge (however the the complete assembly has not been tested to demonstrate it provides adequate backflow protection)Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating ceramic cartridge headworks, single lever operating members and pull down spray with pre-rinse trigger mechanism incorporating an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Both inlet hoses incorporate an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks. The inlet hose assemblies incorporate a servicing valve and is supplied with a single check valve assembly verified by test (suitable for backflow protection against Fluid Category 2). The spout outlets incorporate a plastic aerator. Maximum working pressure 10.00 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (stainless steel – various finishes). The flow of hot and cold water is controlled by a ceramic cartridge headwork with a single lever operating member. The flow of near-boiling water is controlled by a ceramic disc headwork, with spring loaded single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 96°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies with various finishes - see model), incorporating either quarter turn ceramic disc or ceramic cartridge headworks with either a wheel type or single lever operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole single outlet fixed combination tap assemblies incorporating brass bodies (variety of finishes) and quarter turn ceramic disc headwork with either cross top or single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole single outlet fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headwork with cross-top operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap incorporating a brass body (chrome plated), quarter turn ceramic disc headworks and EPDM ‘O’-rings. The spout outlet incorporates a plastic flow straightner. Product is supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates either a plastic flow straightener or aerator depending on model. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. (Model 922041 incorporates a non-rising spindle headworks with dome type operating members) The spout outlets incorporate either a plastic flow straightener or aerator depending on model. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of two hole wall mounted, single outlet (fixed) combination tap assemblies consisting of a concealed brass alloy body incorporating a ceramic cartridge headwork and a chrome finish set (external part) comprising of a face plate, dome type operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies, comprising of a concealed brass body, and a separate trim set (brass body - various finishes), incorporating a ceramic cartridge headwork with a joystick type operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly with brass body (various finishes) incorporating quarter turn ceramic disc headworks with various operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly with brass body (various finishes) incorporating half turn ceramic disc headworks with various operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two-hole deck mounted combination tap assemblies incorporating brass bodies (various finishes) and quarter turn ceramic disc headworks with either cross top or single lever operating members. The products incorporate a manual diverter to a shower outlet with a single lever operating member and the spout outlets incorporate plastic aerator. The products are supplied with a shower handset, shower hose and metal back nuts. Maximum working pressure 5 bar. Maximum working temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks, cross top operating members and self cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever or dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (swivel) combination tap assembly (various finishes) incorporating quarter turn ceramic disk headwork with cross-top operating members. The inlets incorporate approved single check cartridges however the complete assembly has not been tested to demonstrate it provides back flow prevention. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet combination tap assembly with brass bodies (chrome or nickel plated finish, see model) incorporating quarter turn ceramic disc headworks, various operating members, a lockable diverter to the shower outlet and a swivel spout. The shower outlet on the main body incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The spout outlet incorporates a plastic flow straightener, also supplied with an optional areator. The product is supplied with a shower hose and handset and metal backnuts Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members and a locakble self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic aerator. The product is supplied with a shower hose and handset and metal backnuts Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies (chrome plated brass)) incorporating quarter turn ceramic disc headworks and either single lever or cross top operating members (see model). The spout outlets incorporates a plastic aerator and the products are supplied with a lever operated pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with various operating members. The headworks are connected to the spout via stainless steel braided, PEX lined flexible hose assemblies. The spout outlets incorporate a plastic flow straightener and the products are supplied with a lever operated pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of concealed, wall mounted, three hole, single outlet (fixed) combination tap assemblies (various finishes) incorporating quarter turn ceramic disc headwork and cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted three hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic flow straighterner and is also supplied with an optional aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headwork and cross top operating members (models RIV6 CHR & RIV6 GOLD) or dome type operating members (all other models). The spout outlet incorporates a plastic flow straightener and is supplied with an aerator. The products are also supplied with TAQ PEX lined flexible connecting hose assemblies, intended for use between sidebody valves and spout. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (swivel) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks with various operating members and manually operated diverter to a shower hose and handset. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional aerator. The outlet to the shower incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with single lever operating member and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a flow straightener or optional aerator. Both the shower outlet (from the main body) and the inlet to the shower handset incorporate Incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted bath spout outlet incorporating a brass body (chromium plated) and a plastic flow straightener. Maximum operating temperature 60°C.
Wall mounted, spout outlet (brass body with various finishes - see model) incorporating a plastic aerator. The inlet incorporates an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate that it provides back flow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Chlorine dioxide dosing system consisting of PVC-U pipework and fittings. Maximum operating pressure 7.0 bar. Cold water use only.
Expansion vessels incorporating a stainless steel body and EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 100˚C.
Range of filling loop assemblies consisting of an in-line isolation valve, in-line double check valve assembly which also incorporates an isolation valve (suitable for back flow protection against fluid category 3) and stainless steel braided EPDM lined hose. The isolation valves are operated via a single lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use (sizes 12mm-54mm only. 66.7mm, 76.1mm, 88.9mm & 108mm for above ground use only) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Unidelta range of compression fittings with polypropylene bodies with EPDM ‘O’ rings for use with PE100 polyethylene pipe (manufactured to EN12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of outdoor air to water heat exchanger units incorporating a pump, drain valve and isolation valve. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C
Copper brazed micro plate heat exchanger with copper and stainless-steel (316/1.4401) plates. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C
Range of ice making machines. The inlet supply is controlled by a solenoid valve. Inlet hose supplied. Maximum working pressure 5.0 bar. Cold water use only.
Range of commercial air or liquid cooled ice making machines with flow controlled via solenoid valve. Maximum working pressure 7.8 Bar. Cold water use only.
Range of water meters with black epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of flow and temperature sensors with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of circulation fittings with gun metal bodies, plastic cones & guides and EPDM ‘O’ rings. The products incorporate a dynamic venturi valve. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Pressure manager pump control unit with a plastic body. The outlet incorporates a non-return valve. Maximum working pressure 10.0 bar. Cold water use only.
Copper corrugated hose. Maximum working pressure 10.0 bar. Maximum working temperature 90°C.
Chrome plated brass quick connector with EPDM washer. Maximum operating temperature 60°C.
Range of multistage pumps incorporating a stainless-steel housing and impellers. Model MHS170 6M has a maximum working pressure of 7.5 bar. Model MHB145 5M has a maximum working pressure of 6.2 bar. Maximum operating temperature 65˚C.
“Silent” range of booster pumps with plastic bodies and impellers and NBR ‘O’-rings. The SM900165A & SM600165A models incorporate a non-return valve on the outlet. Maximum working pressure 3.2 bar. Maximum operating temperature 35°C.
Shower head incorporating brass body (various finishes) and a flow regulator at the inlet. Maximum operating temperature 85°C.
Shower handset with brass body (various finishes). The inlet incorporates a stainless-steel strainer. Maximum operating temperature 65°C.
Range of shower outlets incorporating brass or stainless-steel bodies (various finishes). Maximum operating temperature 65°C.
Range of shower handsets and hoses with either a brass or stainless-steel body (various finishes). Maximum operating temperature 65°C.
Range of PVC lined flexible shower hoses (chrome plated). H21235-1 incorporates a conical and captive nut, H21235-2 incorporates conical nuts. Model:H21235AB added march 2024 Open outlet use only. Maximum operating temperature 60°C.
Range of shower handsets with plastic body (various finishes). The inlet incorporates a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Shower fixing kit for bar shower valves with stainless steel decorative cover. Maximum operating temperature 65°C.
Range of shower kits comprising of a shower hose, shower handset and shower riser. Both models include a plastic bodied, chromium plated, 3 mode shower handset. The ACY1010 model includes a chrome plated stainless steel inter-locked shower hose with EPDM lining. The ACY 1011 model includes a flexible shower hose comprising of a multi-layered hose (silver external appearance) brass end connections, EPDM washers. Maximum operating temperature: ACY1010: 75°C. ACY1011: 60°C.
Range of overhead shower outlets with chromium plated plastic bodies incorporating stainless steel strainers on the inlets. Models 26 724 xxx & 26 727 xxx incorporate a plastic flow regulator on the inlet. Maximum operating temperature 60°C.
Range of overhead shower outlets incorporating a stainless steel body (various finishes), strainer and flow regulator on the inlets. Maximum operating temperature 60°C.
Range of shower heads with plastic bodies and a brass inlet connection. The inlet of the shower head incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 70°C.
Shower handset with a plastic body (various finishes - see model). Maximum operating temperature 60°C.
Shower handset with a plastic body in a variety of finishes (see model). The inlet incorporates a combined EPDM washer and stainless-steel strainer, and a plastic flow regulator. Maximum operating temperature 60°C.
Range of Y-pattern strainers with bronze bodies, stainless steel strainer and PTFE gaskets. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of wall mounted bib taps (brass bodies) with a rising spindle headwork and ‘T’ type operating member. The spout outlets incorporate a hose union spigot connection. The inlets and outlets of models D2034.G15 and D2034.G20 incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of bib taps incorporating brass bodies. The S0311BL-1 and S0311BL-2 models incorporate an approved single check valve cartridge on the inlet and the outlet (hose union), however, the complete product has not been fully tested to demonstrate it provides backflow protection. The S0311BL-1 and S0311BL-2 models also incorporate a drain port. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bib taps incorporating brass bodies. The BTHUCV1/2 and BTHUCV3/4 models incorporate an approved single check valve cartridge on the inlet and the outlet (hose union), however, the complete product has not been fully tested to demonstrate it provides backflow protection. The BTHUCV1/2 and BTHUCV3/4 models also incorporate a drain port. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bib taps with (chrome plated) brass bodies, brass ball spherical valve with PTFE seals and a single lever operating member. The spout outlet incorporates a hose union spigot connection. Maximum working pressure 10.0 Bar Maximum operating temperature 85°C
Basin pillar tap (chrome plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar Maximum operating temperature 60°C.
Range of pillar taps incorporating brass bodies (chrome plated), quarter turn ceramic disc headworks and cross top operating members. Fittings are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Pillar tap incorporating brass body, quarter turn ceramic disc headwork and EPDM ‘O’-rings. The spout outlet incorporates a plastic flow straightner. Product is supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of shower hoses incorporating stainless steel interlocking outer with PVC inner liner or PVC outer and PVC inner liner (see model). Maximum operating temperature 65°C.
Range of stainless steel or nylon braided, PEX lined flexible hose assemblies available in a range of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Shower hose incorporating a chrome plated stainless steel interlocked casing and a PEX liner. The product is supplied with EPDM gaskets (both models) and ‘O’-rings (YL-PEX-02 model only - M15 end). The product is available in lengths from 300mm-3000mm. Maximum operating temperature 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Shower hose incorporating a chrome plated stainless steel interlocked casing and a PEX liner. The product is supplied with EPDM gaskets (both models) and ‘O’-rings (MS-PEX-02) model only - M15 end). The product is available in lengths from 300mm-3000mm. Maximum operating temperature 85°C.
Range of flexible shower hoses incorporating a PVC inner lining, corrugated stainless steel outer layer (various finishes) and silicone washers. Maximum operating temperature 65°C.
Range of shower hoses with PVC outer (various finishes - see model), PET reinforcement layer, PVC inner liner and EPDM washers. Maximum operating temperature 65°C.
Range of stainless steel braided, EPDM lined flexible hose assemblies available in a range of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘PARINOX/STRONGFLEX S-200' range of stainless-steel braided EPDM lined flexible hose with various end connections (see model). Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of domestic stainless steel indirect unvented hot water storage cylinder incorporating a stainless steel coil for connection to a heat pump circuit. The secondary circuit is factory fitted with a temperature and pressure relief valve (10 bar and 92°C) and an Incoloy immersion heater and magnesium sacrificial anode. Maximum working pressure: Secondary circuit 9.5 bar. Maximum operating temperature 95°C.
Range of manually operated, wall mounted, concealed blending valves with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of manually operated, wall mounted, concealed blending valves with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and self-cancelling diverter. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall mounted exposed thermostatic shower valve incorporating a brass body (various finishes), quarter turn ceramic disc headwork with single lever operating members and manual diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with cross top type operating member. The inlets incorporate a single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). The product is supplied with an overhead shower, shower handset, riser rail and shower hose. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves (chrome plated) brass bodies incorporating a single sequential thermostatic cartridge controlling both flow and temperature. Models 86005770 & 86005780 have single lever operating members. Model 86005760 is not supplied with an operating member. both inlets incorporate single check valve cartridges (suitable for backflow protection against fluid category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic shower valves incorporating brass bodies (chrome plated) and a quarter turn ceramic disc headwork controlling the flow with single lever, cross top or dome type operating members. The temperature controlled is independently via a thermostatic cartridge incorporating a manual override button with cross top, dome type or single lever operating members. Both inlets incorporate stainless steel strainers and approved single check valve cartridges however, the complete assemblies have not been fully tested to demonstrate that they provide adequate backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic bar shower valve, riser rail, shower handset, shower hose and overhead shower outlet. The valve incorporates a brass body (chrome plated) and ceramic disc headwork with dome type operating member which controls and diverts the flow between the two shower outlets. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The inlets incorporate stainless steel filters and a single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Thermostatic cartridge with brass body, and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic mixing valves with a brushed Zinc alloy plated brass body (various operating members) and NBR `O`-rings incorporating a thermostatic cartridge controlling the temperature with a manual override button, a ceramic disc headwork controlling the flow. Both inlets incorporate a single check valve cartridge, (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall mounted thermostatic blending valve (chrome plated brass) incorporating a quarter turn ceramic disc headwork with dome type operating members. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature is 60°C.
Range of wall mounted, concealed, thermostatic shower blending valves incorporating stainless steel bodies, a 2-way ceramic disc headwork and a single lever operating member controlling the flow. The temperature is controlled independently via a thermostatic cartridge with a single lever incorporating a manual override operating member. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic bar type shower mixing valves (chromium plated brass). The246PG model incorporates a 2-way ceramic disc diverter headwork with a dome type operating member controlling the flow between an overhead shower outlet and a shower handset. The 536PG model incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the flow to a shower handset. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Both products are supplied with a shower hose and handset, the B36264 model also includes a shower riser to an overhead shower outlet. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic shower mixing valves with brass bodies (various finishes - see model) incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a combined NBR washer and stainless-steel strainer, as well as an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of adjustable T-type thermostatic mixing valves with brass bodies (chrome plated). Each inlet incorporates a stainless steel strainer and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
T-type mixing valve with a DZR brass body (nickel plated), temperature is controlled by a thermostatic cartridge. Each inlet incorporates a combined EPDM washer and stainless steel strainer, and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe manufactured to EN1057. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies & wedges and EPDM sealing gasket. The closing mechanism is controlled by a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85˚C.
Range of lug type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs, EPDM seats and lever type operating member. Maximum working pressure 16.0 bar (models 2108 12, 2108 13 and 2108 14). Maximum working pressure 10.0 bar (models 210816 and 2108 18). Maximum operating temperature 100°C.
Range of lug type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs, EPDM seats and lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
2-way ceramic disc diverter with a plastic body, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Ceramic disc diverter cartridge incorporating a plastic body for use in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Wall mounted, concealed, 2-way diverter valve (brass body and chrome trim set) with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of ceramic disc type float operated inlet valves with DZR brass bodies. The valves discharge from a downwards atmospheric discharge arrangement on the upper part of the body. Maximum working pressure 5.0 bar. For cold water use only.
Range of wall mounted, concealed flow control valves with brass bodies, incorporating either one or two quarter turn ceramic disc headworks with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
‘Europress’ range of in-line pressure reducing valves, with DZR brass bodies and EPDM ‘O’-rings and washer. The outlet pressure is adjustable between 1.0 - 5.5 bar. Operating parameters: 2430012 EUROPRESS model: Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C. 2430034 EUROPRESS & 2430100 EUROPRESS models: Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 99°C.
Range of adjustable pressure reducing valves incorporating a plastic body and EPDM ‘O’-rings and stainless steel strainers. Outlet pressure 1.2 - 8.0 bar. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 85°C.
Manually adjustable pressure reducing valve, which incorporates a DZR brass body and an in-line double check valve assembly on the inlet (verified by test as suitable for backflow protection against Fluid Category 3). The outlet incorporates a shut-off valve. Maximum supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 40°C.
‘EV220A-W’ range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Aquatsop leak detection system intended to shut the water supply in the event of a water leak. Consisting of two single normally closed servo controlled solenoid valves with a flow regulator and stainless steel filter at the inlet. A LDPE inner hose with corrugated plastic outer hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of latching and normally closed (see model) solenoid valves with plastic bodies, NBR diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
In-line spherical valve incorporating a nickel plated brass body, chromium plated brass ball, NBR rubber ‘O’-rings and single lever operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies, DZR brass ball (sizes ½” to 1”) and bronze ball (sizes 1 ¼” to 2”) PTFE seats and various operating member types (see models). Maximum working pressure: 25.0 bar. Maximum operating temperature: 85⁰C.
Range of servicing valves incorporating brass bodies (chrome plated or natural brass) The P2290 & P2290SI models are spherical valves with brass balls. The 201210 A-80 model is quarter turn with an EPDM seat and ‘O’-ring. The NF721 & NF721SI models are quarter turn with a NBR seat and EPDM ‘O’-ring. The 00711 A-80 is quarter turn with a NBR seat and ‘O’-rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating bronze bodies, wedges and a non-rising stem. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range OF JLA commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with three ¾” x ¾” BSP (F) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet prior to a HDPE inlet hose with ¾” x ¾” captive nut end connections. Maximum working pressure 5.7 Bar. Maximum operating temperature 60°C.
Range of commercial front loading, hood type & utensil washer type dishwashing machines with flow controlled by solenoid and discharged via type AB air gap (verified by test - suitable for backflow protection against fluid category 5) . The products are supplied with a grey coloured PVC supply hose. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
`Hy-MAG` range of electromagnetic water conditioners with blue PTFE coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.
'Droople DRP-M90-IMP'. White coloured, injection moulded acetal cogwheel. For use with water up to 65°C.
'CarSIK-NT'. Grey coloured, RBSiC/SiSiC Reaction Bonded Silicon Carbide washer/seal ring, manufactured by isostatic pressing. For use with water up to 80°C.
'PS5000 Seal'. Grey coloured, compression moulded silicon carbide seal. For use with water up to 85°C.
'SYAL B950' (brown coloured) & 'SYAL A950' (white coloured). Dry press moulded ceramic materials. For use with water up to 85°C.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'42.5 (HSR)'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SW-02'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquafitting Blue'. Factory applied, blue coloured epoxy coating. Apply and cure as per manufacturer's instructions file number 'DLCHB-CO-001', edition 'A1', issue date '2021-April-11st'. For use with water up to 65°C.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'DUAYEN E-39'. Factory applied, two-component, red coloured (once mixed) epoxy coating. Mix Parts A&B in a volume ratio of 79.5:20.5 and apply as per manufacturer's instructions '00.05102021'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Belzona 1321`. Site applied, two-part, epoxy amine coating available in grey or blue colours. Mix base and hardener in a 11:1 mass ratio. Apply and cure as per manufacturer’s IFU ‘FN10026’, publication number ’02-09-21’. For use with water up to 23°C. These materials are only approved for the mixing conditions that appear on the approval. If the mixing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic®-6100 FX White’ (formerly known as ‘MasterSeal 6100 FX White’) ‘Sikalastic®-6100 FX Grey’ (formerly known as ‘MasterSeal 6100 FX Grey’. Site applied, two-component cementitious coating. Mix ‘Sikalastic®-6100 FX White’ (Coat 1) with water in a mass ratio of 15:5.6. Apply and cure for 1 day@5°C before applying Coat 2. Mix ‘Sikalastic®-6100 FX Grey’ (Coat 2) with water in a mass ratio of 15:5.6. Apply and cure for 5 days@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquakote Grey for use with Aquakote Blue'. Site applied, blue coloured (once applied), two-component epoxy coating. 'Aquakote Grey’ is the base coat and comprises of Parts A (grey liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C before applying top-coat. 'Aquakote Blue’ is the top-coat and comprises of Parts A (blue liquid) & B (amber liquid) which are to be mixed in a 100:17 mass ratio and then applied in a wet film thickness of 200µm. Cure for 12 hours@10°C. For use with water up to 23°C. Please note that 'Aquakote Grey & Aquakote Blue' are to be used in conjunction with each other. the approval does not cover 'Aquakote Grey and/or Aquakote Blue' when applied as a single coat.
'Tesnit BA-60'. Orange coloured aramid fibre/NBR gasket material. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
`Novapress 260`. Green coloured, compressed fibre material (bound with NBR), manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
`Ruby Veg Soft Soap/EasyJoint Uni`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet 'revision 2' dated '22/09/21'. For use with water up to 23°C.
'LATAMID 66 H2 G/30 BLACK F:3352'. Black coloured, injection moulded PA66 material. For use with water up to 65°C.
'CELANYL A2 WR GF30 NC 1102/2A & CELANYL A2 WR GF30 NC 1102/2B'. Off-white, injection moulded nylon materials. For use with water up to 85°C.
'POLYPOL-1052'. Pale yellow/beige coloured, isophthalic unsaturated polyester resin material. For use with water up to 50°C.
'VICTREX' injection moulded PEEK thermoplastic materials. For use with water up to 85°C. VICTREX PEEK 450GL30, 450G, 450FE20 (natural – appears beige coloured), 450FC30, 450CA30 & 90GL30BLK-EU (black coloured). VICTREX FG™100, FG™120, FG™200, FG™220, FG™300 & FG™ 325 (natural – appears beige coloured). VICTREX FG™101, FG™121, FG™140, FG™201, FG™221, FG™240, FG™301 & FG™320 (black coloured). VICTREX FG™340 (dark grey coloured).
'Lucite Diakon ST25G8 Clear 0003'. Colourless, injection moulded PMMA material. For use with water up to 23°C.
'AO Roto Water Tank Panel'. White coloured, LLDPE tank panel manufactured by rotational moulding. For use with water up to 60°C.
'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Total 4041 Blue Polyethylene & Total 4041 Black Polyethylene'. Blue or black coloured, polyethylene material manufactured by rotational moulding. For use with water up to 65°C.
'CONTINUUM DGDA-2610 BK'. Black coloured, compression moulded HDPE (PE100) material. For use with water up to 23°C.
'TP11115 Prisma Black'. Black coloured LLDPE material manufactured by rotational moulding. For use with water up to 70°C.
'F420B00 natural (appears off-white), F420B99 (black coloured) & F410K01 (white coloured)'. Injection moulded, glass filled polypropylene materials. For use with water up to 85°C.
'Chang QI/CFPC'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'G400 & G400B' seat components. White coloured, extruded PTFE seat components. For use with water up to 85°C.
'(UREFLEX) TM390'. Off-white coloured, injection moulded PUR material manufactured by casting. For use with water up to 23°C.
'EX1'. Site applied, grey coloured (once mixed), two-component anchor resin. Mix, apply and cure as per manufacturer's product information 'EX1 V2.08' Issued '08/2021' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
'LOPI60 & LOPI70'. Black coloured, injection moulded, EPDM 'O' rings. Shore hardness 60 & 70 respectively. Tested in-radius size 0.75mm. For use with water up to 85°C.
`RG EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'SEAEP80N01'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'E8121'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80A. Tested in-radius size 1.55mm. For use with water up to 85°C.
'EBW-65'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.98mm. For use with water up to 85°C.
'E701/A'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 23°C.
'RCI EP 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 65°C.
'OLDAL VMQ880 65TR – VMQ4303'. Colourless (translucent), extruded VMQ rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SB1 Bonding Agent'. Factory applied, black coloured bonding agent intended to bond plastic or brass to rubber. Apply and cure as per manufacturer's instructions 'LDAP-003 issue 1' dated 11-08-2016. For use with water up to 85°C.
'Klinger® Top-Chem 2005'. Red coloured, filled PTFE gasket material manufactured by calendaring. For use with water up to 23°C.
'Mega All White'. White coloured (opaque) anaerobic sealant/adhesive. Apply in strict accordance with manufacturer's instructions 'issue 01' dated '09/09/2021'. For use with water up to 85°C.
'Key Plumb'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ixef DW 1022 BK001 & Ixef FC-1022 BK001'. Black coloured, injection moulded polyarylamide materials. For use with water up to 85°C.
'DESTONE DSC7500G6'. Black coloured, injection moulded polyketone material. For use with water up to 85°C.
'ULTEM', injection moulded polyetherimide materials. For use with water up to 85°C. PW1000-1000, PW1000-1000 and PW1000-1000W (yellow coloured). PW2100-1000, PW2100-1000 and PW2100-1000W (brown coloured). PW2200-1000 & PW2300-1000 (beige coloured). PW2400-1000 (grey coloured). PW1000-7101, PW2100-7301, PW2100-7301, PW2100-7301W, PW2200-7301, PW2300-7301 & PW2400-7301 (black coloured). ULTEM PW2300-1000 and ULTEM PW2300-1000W were added to the approval in June 2025.
'Hytrel® HTR6108'. Translucent cream coloured, injection moulded thermoplastic elastomeric material. Shore hardness 61. For use with water up to 85°C.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of WC flushing cisterns incorporating a BS 1212-4 (2016) side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres or 4.5/3 litre flush volumes. The cistern is operated by a manual push button and the product incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Type TK, spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Self closing press headwork cartridge with brass body and EPDM ‘O’-rings and NBR gasket, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-rising spindle headwork incorporating a brass body and NBR ‘O’-rings to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Ceramic cartridge headwork incorporating a plastic body and EPDM rubber seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Quarter turn ceramic disc headwork incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
A ceramic cartridge headwork with a plastic body and EPDM ‘O’-rings for insertion into specifically dimensioned assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Thermostatic cartridge incorporating a plastic body, stainless steel strainer and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some models are supplied with a pop-up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Some products are supplied with a pop-up waste or a click type waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Ragfe of single hole, single outlet (fixed) combination tap assembly with stainless steel bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator with an integral flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Product supplied with an approved click-type pop up waste. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 36 100 xxx model is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and flow straightener The inlet hoses have integral screwdriver operated isolation valves. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet has a plastic aerator and model 31 531 XXX is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated) incorporating a joystick controlled ceramic cartridge headwork. The spout outlets incorporate a plastic aerator. Models 39 031 xxx & 39 035 xxx are supplied with lever operated pop-up wastes and model 39 032 xx is supplied with a pop-up waste kit. Maximum working pressure: 10.0 bar. Maximum operating temperature 60°C.
Floor-standing single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.9 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel), combination tap assemblies (chromium plated brass). Incorporate a quarter turn ceramic disc headworks with single lever operating members (Models Cresta, Sion & Henley) or ceramic cartridge headworks with single lever operating members (model Reno). The inlets incoprorate approved check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The cold inlet hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic disc headworks with a single lever operating members. The spout outlet incorporates a plastic flow straightener or aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (stainless steel body - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator with an integral flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a push to open, push to close ‘detent’ headwork and the spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
A range of single-hole, single outlet, (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate an plastic aerator. The fitting is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60ºC.
Wall mounted two-hole, single outlet (fixed) combination tap assembly with a brass body (chrome trim set) incorporating a ceramic cartridge headwork and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets are a waterfall type incorporating a stainless steel strainer. The products are supplied with plastic or brass backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlets are a waterfall type incorporating a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks or a ceramic cartridge headwork (SH-T8025A model only) with various operating members (see models). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with various operating members (see models). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks or a ceramic cartridge headwork (SH-T8025N model only) with various operating members (see models). The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating ceramic cartridge headworks with single lever operating members Spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet, (fixed) combination tap assemblies (chromium plated brass), Models 49723, 26684 & 18193 incorporate a non rising spindle headwork with dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. . Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) concealed combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks, single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightner. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet, fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, shower handset and metal backnuts, Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (brass body with various finishes - see model), incorporating a 2 way ceramic disc diverter headwork controlling the flow between the spout or shower outlet with a single lever operating member. Temperature is controlled independently via a thermostatic mixing valve incorporating a single lever operating member with a manual override button. Each inlet incorporates an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum working temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks with either single lever or cross top (SH-T8181 model only) operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks various operating members (see models) and a manual diverter to shower outlet. The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with either single lever or dome type (SH-T8062 model only) operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlets are a waterfall type incorporating a stainless steel strainer. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A range two-hole wall or floor mounted combination tap assemblies incorporating brass bodies (variety of finishes), and quarter turn ceramic disc headwork with either cross top or single lever operating members. The products incorporate a manual diverter to a shower outlet with a single lever operating member and the spout outlets incorporate plastic aerator. The products are supplied with a shower handset & shower hose. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members and a manual diverter to the shower outlet. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet, fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, shower handset and metal backnuts, Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a waterfall outlet. The products are supplied with a shower hose and handset, and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate either a plastic flow straightener or plastic aerator (SH-T9071 model only). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly with brass body (chrome plated), incorporating quarter turn ceramic disc headworks, single lever operating member and self cancelling diverter to shower outlet. The temperature is controlled independently via a thermostatic cartridge with single lever operating member. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of floor mounted, two-hole, single outlet (swivel) combination tap assemblies (stainless steel and brass bodies various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, shower handset and metal backnuts Maximum working pressure 5.0 bar. Maximum operating temperature 60°C. .
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with a shower hose and handset, and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (various finishes - see model), incorporating quarter turn ceramic disc headworks and either single lever or dome type operating members (see model). The spout inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Three hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. Spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator (except Broadway and Niagara spout options). The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The spout junction of the Malmaison and Niagara spout options incorporates a plastic flow regulator. The product is also supplied with either a click type or pop-up waste (see model), and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes). Incorporating quarter turn ceramic disc and various operating members. The spout outlet incorporates a plastic aerator. The product is supplied with nylon braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections on both ends or at one end and M10 at the other. The hoses are intended to connect between the side body headworks and the spout junction. The product is also supplied with a pop-up waste, and a ½” BSP (F) nut and NBR washer to adapt the side valve inlet connections. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet (fixed) combination tap assemblies incorporating brass bodies (various finishes), quarter turn ceramic disc headwork and choice of single lever or dome type operating members. The spout outlets incorporate a plastic aerator. The product is supplied with stainless steel braided PEX lined flexible hose assemblies for connecting the side body headworks and the spout junction. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass spout and trim set), incorporating quarter turn ceramic disc headworks with dome type operating members. The inlet of the spout incorporates a plastic flow regulator, and the spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet, (fixed) combination tap assemblies with brass bodies (chromium plated), incorporating quarter turn ceramic disc headworks with dome type operating members. The product is supplied with stainless steel braided PEX lined flexible hose assemblies for connecting the side body headworks and the spout junction. The spout inlet incorporates a plastic flow restrictor, and the spout outlet incorporates plastic aerator. The products are supplied with click type pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (various finishes, see models) incorporating quarter turn ceramic disc headworks with wheel type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Four hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc head work with single lever operating members (model WAI4BSMXX) and self cancelling diverter to shower outlet. The fitting is supplied with Stainless steel braided PEX lined flexible connecting hoses. The spout outlets incorporate a plastic aerator. Product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of spout outlets incorporating stainless steel bodies (various finishes) and a plastic aerator. Maximum operating temperature 60°C.
Range of wall mounted spout outlets incorporating brass bodies (various finishes) & plastic aerators. Maximum operating temperature 60°C.
Spout outlet with a brass body (chrome plated). The spout outlet incorporates a combined plastic flow regulator and aerator. Maximum operating temperature 60°C.
Range of wall mounted spout outlets with brass bodies (chrome plated). Product is supplied with various operating members and pop up click waste. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Wall mounted waterfall, bath spout (chromium plated brass), incorporating a flow regulator on the inlet and stainless-steel strainer at the spout outlet. Maximum operating temperature 80°C. Open outlet use only
Range of wall mounted spout outlets, (brass bodies with various finishes) incorporating a plastic aerator. Maximum operating temperature: 60°C
‘Profine’ plastic bodied filter head incorporating EPDM ‘O’-rings for use with filter cartridges (not supplied).For use with LLDPE tube (manufactured to DIN 8072). All models can be specified with or without an integral bracket. Maximum working pressure 6.0 bar. Cold water use only.
Range of carbon block water filters and housings. Maximum working pressure 10.5 bar. Cold water use only.
Range of water filter housings with plastic heads and bodies (various colours - see model), incorporating NBR ‘O’-rings (158087/088/207/208/218/219/261 models only) or with EPDM ‘O’-rings (all other models). Big Blue for Cartridges - Maximum working pressure 6.9 bar (10” filter housings) and 6.2 bar (20” filter housings). Maximum working temp 38°C. All other models - Maximum working pressure 8.62 bar. Maximum working temp 52°C.
Carbon block filter cartridge with plastic body. The cartridge may be installed with a manifold (filter head) for use with PE tubing manufactured to BS 1972. Maximum working pressure 8.6 bar. Cold water use only
‘Multi Press Leak M.P.L’. range of fittings (pressing profile TH and U) for use with Alpex Duo XS multi-layered pipe. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass, chrome plated brass or DZR brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of M type press fittings with TP2 copper bodies and EPDM ‘O’-rings, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Dual flush WC outlet valve with an ABS body, incorporating a silicone seal & internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of urinal flushing mechanisms with a solenoid valve controlling the flow. The valves are controlled via an infra-red sensor. The inlet incorporates a stainless steel strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
‘Aquila V4 C1’ range of water meters (brass or bronze bodies) with a plastic working chamber, flow regulator and impellor, and either NBR or EPDM ‘O’-rings. The products are supplied with loose NBR/fibre flange gaskets. Maximum working pressure 16.0 bar. Cold water use only.
A range of water meters incorporating brass or plastic bodies (See models), EDPM ‘O’-rings, plastic strainer on the inlet and a plastic impellor. Maximum working pressure 16.0 bar. Maximum working temperature 85°C (brass bodies) or cold water use only (plastic bodies)
Range of water meter assemblies which incorporating DZR brass bodies, spherical valve and pressure reducing valve (1.5 to 6.0 bar range). The products incorporate two approved, in-line single check valve cartridges, (verified by test, suitable for backflow protection against Fluid Category 3). Fitting is also supplied with a pressure guage. Maximum working pressure 10.0 bar. Cold water use only.
Range of meter boxes incorporating a plastic manifold arrangement consisting of a stop valve with non-rising spindle , check valve (however the complete assembly has not been tested to demonstrate it provides adequate backflow) and concentric meter port. Some models incorporate a drain off or blacking plug. Connections can be compression or push fit (see model). For use with PE8-0 pipe to BS EN 12201 and copper to EN 1057. Maximum working pressure 16.0 bar. Cold water use only.
Range of pushfit hose connectors with either plastic (white or black) or chrome plated brass bodies and EPDM ‘O’-rings. SHCV prefix models incorporate screwdriver operated servicing valves. All pushfit connections are for use with PEX pipe (manufactured to BS7291-3) and copper pipe (manufactured to EN1057). Barbed end connections are not approved for use with any hose. Chrome plated brass body models are also for use with PB pipe (manufactured to BS7291-2). Maximum working pressure 10.0 bar (servicing valve models only). Barbed end connections are open outlet use only. Cold water use only.
Range of water hammer arrestor’s incorporating brass bodies (various finishes). The 525152 model is supplied with a reinforced captive nut. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C. For products manufactured from June 2023 Maximum operating temperature 85°C
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of flow control valves for domestic hot water with plastic bodies and EPDM ‘O’-rings The products incorporate a motor which adjusts the flow, a flow sensor which measures the flow rate and a plastic filter on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pressure gauge with brass body and a plastic case. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C
Range of bidet spray kits comprising of a hand set with self-closing trigger, wall bracket, flexible hose assembly, thermostatic blending valve and isolation valve. Maximum working pressure 5 bar. Maximum working temperature 60°C
‘Para Z’ range of circulating pumps with either stainless steel, bronze or plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘e-SH’ range of centrifugal booster pumps with a blue polymer coated stainless steel body, stainless steel impeller and EPDM ‘O’-rings. Maximum working pressure 12.0 bar. Cold water use only.
Range of wall mounted and overhead shower outlets, incorporating stainless steel strainers and flow regulators at the inlets. Maximum operating temperature 60°C
Shower outlets incorporating chrome plated ABS bodies. Maximum operating temperature 65°C.
Range of overhead showers and shower handsets with plastic body (various finishes). Overhead shower inlets incorporate a stainless steel strainer Maximum operating temperature 60°C.
Range of shower handsets incorporating plastic bodies (various finishes), plastic flow regulators and stainless steel strainers. Maximum operating temperature 60°C.
Range of shower kits, shower outlets and shower hoses. The shower handsets and overhead shower inlets incorporate a plastic flow regulator. Maximum operating temperature 45°C.
Shower handset with a plastic body in a variety of finishes (see model). The inlet incorporates a combined EPDM washer and stainless-steel strainer, and a plastic flow regulator. Maximum operating temperature 60°C.
Shower kit consisting of a wall mounted elbow (brass body various finishes - see model), shower hose and handset. The outlet of the wall elbow incorporates a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The shower handset inlet incorporates a stainless-steel strainer and a plastic flow regulator. Maximum operating temperature 60°C.
Range of shower outlets and shower handsets. The shower heads have a brass body and ball joint, NBR ‘O’-ring, stainless-steel strainer and silicon nozzles. The shower handset has a brass body, NBR ‘O’-rings, silicon nozzles and incorporate a plastic flow regulator on the inlet. Model ‘100274774 N200000068’ is supplied with a double interlocked hose and a single check valve cartridge (to be installed on the inlet to the hose) however the complete product has not been fully tested to demonstrate it provides backflow protection. Model ‘100274774 N200000068’ has a maximum operating temperature of 60°C. All other models have a maximum operating temperature of 85°C.
Range of shower hoses and handsets (various finishes - see model) with EPDM ‘O’-rings. Maximum operating temperature 60°C.
Range of wall mounted shower kits, incorporating a shower handset, shower hose and wall elbow connection. Maximum operating temperature 60°C.
Range of shower columns with chromium plated brass bodies. Maximum operating temperature 60°C.
Range of shower handsets plastic bodies (various finishes) and EPDM ‘O’-rings. All models include a button on the shower face which alters the spray pattern. The product incorporates either a plastic strainer (26 050 & 26 530) or a stainless-steel strainer and a plastic flow regulator (26 051 & 26 531) on the inlet. Maximum operating temperature 60°C.
Range of pillar taps incorporating brass bodies (various finishes), quarter turn ceramic disc headworks and various operating members. Spout outlets incorporate either a plastic aerator or flow straightener (all models apart from STA13-QT). Fittings are supplied with metal backnuts Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps with brass bodies (various finishes) incorporating non-rising spindle headworks using either dome type or cross top operating members. Spout outlets incorporate plastic flow straighteners. The products are also supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps incorporating either stainless steel or brass bodies (various finishes), quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The RB3 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Self-closing basin pillar tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlet incorporates a chrome plated plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of interlocking metal shower hoses with silicone liner and EPDM washers. Maximum operating temperature 70°C.
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
Range of indirect and direct unvented storage cylinders consisting of either no coil (GLE) or a factory fitted single (GLC) or twin coil (GLT). The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@85˚C for 1.0-6.0 bar products and 10.5 bar@95°C for 6.0-10.0 bar products. The products are supplied with an inlet control group (safety kit) consisting of a pressure reducing valve, an expansion relief valve 6.0 bar (1.0-6.0 bar products) or 10.5 bar (6.0-10.0 bar products) and an approved check valve, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is also supplied with an expansion vessel. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
T-type mixing valve with a DZR brass body (nickel plated), temperature is controlled by a thermostatic cartridge. For use with copper pipe manufactured to EN1057. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, bar type, thermostatic shower blending valves (chromium plated brass), incorporating a ¼ turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a stainless steel strainer and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, concealed, thermostatic shower valves with brass bodies and trim sets (various finishes - see models). Flow is controlled as follows (for operating members - see model): Single outlet models: ¼ turn ceramic disc headwork. Double Outlet Models without diverter: ¼ turn ceramic disc headworks. Double Outlet Models with diverter: 2-way ceramic disc diverter headwork. Triple Outlet Models with diverter: ¼ turn ceramic disc headwork and a 2-way ceramic disc diverter headwork. The temperature is controlled independently via a thermostatic cartridge with various operating members (see model) which incorporates a manual override button. The inlets incorporate a single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. Specific models are supplied with a shower hose and handset (see models). Maximum working pressure 5.0 Bar Maximum operating temperature 60°C
Wall mounted bar type thermostatic mixing valve (chromium plated brass) incorporating a ¼ turn ceramic disc headwork controlling the flow with a dome type operating member and a secondary ceramic disc headwork diverting the flow between the overhead shower and hand shower with a single lever operating member. The temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. Both inlets incorporate single check valve cartridges, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The product is supplied with a fixed overhead shower, shower handset and hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, exposed thermostatic shower valve (chromium plated brass) incorporating a thermostatic cartridge that controls the temperature and a shut off valve that controls the flow both with a single lever operating member. The inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wafer and lugged type butterfly valves incorporating blue epoxy coated cast iron bodies, stainless steel discs and EPDM seat. The closing mechanism can be controlled by either a lever, gear or bore shaft. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of double flanged and wafer type butterfly valves with cream epoxy coated cast iron bodies, EPDM seats and a range of discs (see models). Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of ‘Keraflo Aylesbury’ ceramic disc operated inlet valves with DZR brass bodies and ABS or copper outlets. K and KAX type float mechanism incorporate a polyethylene float and spirit level for installation. The KB type float mechanism is operated by a transfer of weight within the actuator tube, which is connected to a polyethylene buoy and weight via stainless steel chain. Maximum working pressure 10.0 bar. Cold water use only.
Range of non return valves incorporating bronze bodies and discs, and PTFE washer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of 5 way inlet control group assembly incorporating a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range of either 3.0 bar, 3.5 bar, or 6.0 bar and a safety relief valve set at either 6.0 bar or 8.0bar (depending on model). The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2). Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C
Range of adjustable pressure reducing (pilot) valves with stainless steel bodies, EPDM diaphragm and ‘O’-ring. Outlet pressures are adjustable between 1.0 to 5.0 bar (ACV100C model), 1.5 to 10.0 bar (ACV100E model) and 2.0 to 15.0 bar (ACV100F model). Maximum supply pressure 16.0 bar. Cold water use only.
Range of adjustable, pilot operated, pressure reducing control valves with black plastic bodies, EPDM diaphragm, EPDM ‘O’-rings and NBR seals. The products are supplied with auxiliary stainless-steel tubing, lever operated spherical valves, integral stainless-steel strainer, pilot valve and a quarter turn ceramic disc valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 0 - 8.5 bar, 7.0 - 13.5 bar or 12.0 - 16.0 bar (see model). Maximum operating temperature 60°C.
Range of pre-set, spring loaded, angled pressure relief valves with plastic body and EPDM diaphragm. The valves are fitted with rotary type easing gear . For maximum working pressure please refer to model. Maximum operating temperature 99°C.
Range of pre-set pressure relief valves with bronze bodies and EPDM seating discs. Available with either a manual lever or dome type sealed cap. Pre-set relief pressures: DN15 and DN40 valves: 0.35 bar to 15.9 bar. DN20 valves: 0.35bar to 13.8bar. DN25, DN32 and DN50 valves: 0.35 bar to 12.5 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves incorporating brass bodies (chrome plated), brass balls and PTFE seals. Maximum working pressure 40.0 bar. Maximum operating temperature 100°C.
Flow through valve with a brass body and EPDM ‘O’-rings, incorporating a spherical valve and a separate drain port/plug. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of 5 way inlet control group assemblies with a DZR brass body incorporating a pressure reducing valve, with an adjustable outlet pressure range between 2.7 and 3.3bar and a safety relief valve set at 8.0 bar. The product incorporates an inline single check valve cartridge after the balanced cold take off, verified by test (suitable for backflow protection against Fluid Category 2) and strainer on the inlet Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C
Range of cold water inlet control groups with DZR brass bodies, consisting of a pressure reducing valve, (all models are adjustable between 1.0 and 6.0 bar, but some come pre-set from the factory - see model), a pressure relief valve (set at 6.0 or 8.0 bar - see model) and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The pressure relief valve is fitted with a rotary type easing gear. All products for use with copper pipe manufactured to BS EN 1057. Maximum inlet supply pressure 20.0 bar. Cold water use only.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of electrolytic water conditioners, with a brass body and zinc alloy anodes. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.
'BPL HB QD Bitumen Black 60'. Factory applied, black coloured bituminous coating. Apply and cure as per manufacturer's data sheet number '671' dated 'Apr-20'. For use with water up to 60°C.
'XFGJ-2'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DAT-01'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 34.4:44.9:20.7. Cure for 8 hours@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kerjiwal SRC'. Factory applied, grey coloured Sulphate Resisting Cement. Mix cement, sand & water in a volume ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Orgal® Hydroflex 10'. White coloured, acrylic polymer emulsion cement modifier, which is a liquid additive intended to be mixed with cement to achieve a coating. Mix cement:additive:water in a 197.5:30:10 mass ratio and apply as per manufacturer's instructions '2/18'. Cure for 28 days@23°C and @50% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sungyoung GRP Water Tank Panel'. Light grey coloured, hot pressed GRP panel. For use with water up to 50°C.
'Futurewrap Potable'. Light green coloured GRE material manufactured by hand lay-up. For use with water up to 50°C.
'Acquablu Hose'. Extruded hose comprising of a white coloured (transparent) polyethylene inner layer, off-white coloured chlorobutyl second layer, rayon reinforcement layer and blue coloured bromobutyl outer later. For use with water up to 60°C.
'TUCAI WRAS EPDM hose'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 0.68mm. For use with water up to 70°C.
`HYDROFAS'. Black coloured, extruded polyethylene (PE 80) pipe. For use with water up to 23°C.
'UP 203 Black & UP 204 Black'. Black coloured polyethylene materials manufactured by rotomoulding. For use with water up to 23°C.
'UP 203 Natural & UP 204 Natural'. Natural (appears white), LLDPE materials manufactured by rotational moulding. For use with water up to 23°C.
'RavaRoto 3850UV black & RavaRoto 3930UV black'. Black coloured LLDPE materials manufactured by rotational moulding. For use with water up to 23°C.
'RavaRoto 3850UV natural & RavaRoto 3930UV natural'. Natural (appear white) LLDPE materials manufactured by rotational moulding. For use with water up to 23°C.
'HEXELL SC 3093 TYPE NATURAL'. Natural (appears white), rotmoulded LLDPE material. For use with water up to 23°C.
'HEXELL SC 3093 TYPE BLACK G01'. Black coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'HEXELL SC 3093 TYPE GREY B22 MIX B11'. Grey coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'TASNEE 100 Black'. Black coloured HDPE material manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Floraseal'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'Unecol CINTAS'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'KLINGER® top-chem 2000'. Grey coloured, SiC filled PTFE material manufactured by calendaring. For use with water up to 85°C.
'AQUAPEA® In-line Repair'. Site applied, dark grey coloured (once mixed), two-part epoxy putty (light grey and dark grey coloured) and polypropylene core (white, translucent). Mix & cure as per the document: “Aquapea method statement issue 1 dated 23-04-21” . For use with water up to 23°C.
'4273 'O' rings and washers'. Black coloured, injection moulded EPDM 'O' rings and washers. Shore hardness 70. The 'O' rings have an in-radius size of 1.31mm. The washers have an in-radius size of 2.00mm. For use with water up to 85°C.
'QC'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 23°C.
'HYPRESS12V'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. Between June 2021 and August 2022, the material was for use with water up to 23°C. Between September 2022 and June 2026, the material is for use with water up to 65°C.
'S/EP-50, S/EP-60, S/EP-70 & S/EP-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50A & 80A. Tested in-radius size 1.05mm. For use with water up to 65°C.
'ILPEA 70-90 EPDM COMPOUND WRAS AF'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.25mm. For use with water up to 23°C.
'EPDM-W E267'. Black coloured, compression moulded EPDM material. Shore hardness 80A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Hongli IRHD50'. Black coloured, press moulded EPDM material. Shore hardness 50. Tested in-radius size 1.12mm. For use with water up to 50°C.
'A-KT 70-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 70. Tested in-radius size 1.00mm. For use with water up to 23°C.
'Viton `A` V99 gaskets'. Black coloured gaskets cut from calendered fluoroelastomeric material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 23°C.
'70NBR103F'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C.
'TEC S147 R.-45 ROSSO'. Orange coloured, injection moulded, silicone rubber 'O' rings & gaskets. Shore hardness 45. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'Silicone LSR2090-50'. Colourless (translucent), injection moulded silicone rubber material. Shore hardness 50. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 85°C.
Page 1 of 12
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
