‘Rashmi Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/002', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ZISIF GRP water tank panel'. For use with water up to 23°C. ‘ZISIF Premium GRP Water Tank Panel’ was added to the approval in February 2026 and is for use with water up to 55°C. Off-white coloured GRP panels manufactured by hot press moulding.
'Radilon A RCM4010RKC 306 BK'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 85°C.
'BAILUN U-PVC Pipe (UPVC1617)'. Grey coloured, extruded U-PVC pipe. For use with water up to 23°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'EPDM-50AA2, EPDM-60AA2, EPDM-70AA2, EPDM-80AA2 & EPDM-85AA2'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 ShA & 85 ShA. Tested in-radius size 1.0mm. For use with water up to 65°C.
'SIL60 RED 'O' rings and seals'. Red coloured, injection moulded silicone rubber 'O' rings and seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.25mm. The seals have a tested in-radius size of 0.90mm. For use with water up to 85°C.
'E-Tupling Plastic Pipe Cement 125 ml ETSC125' & 'E-Tupling Plastic Pipe Cement 250 ml ETSC250'. Clear, transparent (un-pigmented) solvent cements, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TODAY TOOLS PVC SOLVENT CEMENT 125ML SC1' & 'TODAY TOOLS PVC SOLVENT CEMENT 250ML SC2'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TW Tools PVC Pipe Cement 125ml' & 'TW Tools PVC Pipe Cement 250ml'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies, various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Depending on model the products are supplied with either a stainless steel braided PEX lined flexible hose assembly with 15mm spigot end connection or 10mm copper tail (see models). Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Bottom entry BS1212 part 4 (2016) compact type float operated inlet valve for WCs flushing cistern having a plastic body and adjustable float and plastic filter at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)he shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator, and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of floor mounted, single hole, single outlet, swivel combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of shower kits with a shower hose, handset and shower rail. Maximum operating temperature 60 °C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
Range of wall mounted shower kits. Comprising of brass bodied wall mounted shower outlet, shower hose and handsets (various finishes), incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60*C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates a lever operated spherical valve and stainless-steel strainer. For use with BS EN1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of boiling water dispensers incorporating stainless steel water tank (3Ltr, 5Ltr, 10Ltr and 13Ltr) with inlet supply controlled via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. Maximum working pressure 7.0 Bar Maximum operating temperature 96.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-1 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-2 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-3 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No |
D30PF and D30PF-1 only different in the color of Item 11 and Item 13 D30PF-2 and D30PF-3 only different in the color of Item 11 and Item 13 DN30PF and D30PF-2 only different in the shape of Stem
Range of thermostatic cartridges with plastic bodies and stainless-steel filters, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-down spray type incorporating a push button. The connection to the pull-down hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies incorporating a brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The outlets incorporate a plastic aerator. Model CO721XX incorporates a pull-out spray with push button trigger assembly. The pull-out spray incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Model CO713XX incorporates a pull-down outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (white finish), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlet is a pull-out spray type. The inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). incorporating a ceramic cartridge and single lever operating member with a spring loaded, pull down trigger operated spray. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 143138 X XXX | VARIOUS | 1/2" | 10.0 bar | 65 °C | PPI | Rear of body | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8142KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8122KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8142KPM-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
1）Model No. without Suffix-Chrome 2) -**Represents the following different surface treatments: 1. H-Black 2. DYB - Matte white 3. BZ - Perl white painted 4. HGTS - Red bronze 5. HTL = Yellow bronze brushed 6. Q = Bronze 7. QTSL = Bronze brushed bright 8. QTS = Bronze brushed matte 9. STS = Acid copper brushed 10. SDMGJ = Water plated rose gold 11. N = Nickel brushed bright light 12. NP = Nickel brushed 13. TJ = Titanium gold 14. TJLS = Titanium gold brushed 15. G = Gold 16. GJS = Gold brushed 17. GJSY = Zirconium gold wire drawing matte 18. PGJFY = Zirconium gold wire drawing matte bright light 19. PLSJ = Brushed gold 20. LSJY = Brushed gold matte 21. MGJ = Rose gold 22. MGJL = Rose gold brushed 23. DMGJ = Light rose gold brushed 24. HTS = Red bronze brushed 25. QHP = Grey 26. LSQH = Grey brushed 27. LHMGJ = Brushed yellow rose gold 3) The finish is on metal body
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 197021 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | Non-rising spindle | C-plate | Aerator & Flow Straightener | |
| 207121 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 207125 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Cross top Dome or Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole, single outlet (swivel) combination tap assembly with a brass body incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerator or flow straightener with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 12101246 | Various | 1/2" captive nut | 10 bar | 65 °C | EASO | Rear of body | No | 1/4 Turn ceramic disk | Nut with screws | Aerator |
Chrome plated, Brushed brass, Brushed nickel or Matt black
A range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is also supplied with an alternative spout outlet that incorporates a plastic flow straightener and a stainless-steel strainer. The products are supplied with a loose brass ½” BSP (M) x ½” BSP (F) adaptor for installation on the cold inlet. This adaptor incorporates a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum working temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a quarter turn ceramic disc headwork with cross top or dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193706 X XXX | VARIOUS | ¾” BSP (M) | 10.0 bar | 85 °C | PPI | Rear of tap body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : H (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a stainless steel strainer and a plastic flow straightener.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T10105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T20405 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21005 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T30605W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T31505 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40105W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T40205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T40415 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T50805 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
1.The model number suffix without B indicates chrome plated. The model number suffix with B indicates black. The model number suffix with BB indicates Brushed brass. 2.Only SL-T40415, SL-T40205 & SL-T40105W suffix with G indicates Champagne Gold.
Range of wall mounted, two-hole single outlet combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Wall mounted thermostatic blending valve (brass body, various finishes - see model) incorporating a 2-way ceramic disc headwork with a single lever operating member controlling and diverting the flow between the spout outlet or the shower outlet. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 16.0 bar. Maximum operating temperature 75°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with lever type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M5005 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall mounted, two-hole, single outlet (fixed) bath/shower mixers, (brass bodies – various finishes). Incorporating a thermostatic cartridge controlling the temperature and a manual diverter controlling the flow between the outlets with dome type operating members. The spout outlet incorporates a plastic aerator. Both inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Two hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products Incorporate either a non-rising spindle (model 1641 only) or quarter turn ceramic disc headworks (all other models) with either cross top (model 1641 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a a pop-up waste not verified by test. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products incorporate either a non-rising spindle (model 1851 only) or quarter turn ceramic disc (model 1850 only) headworks with either cross top (model 1851 only) or single lever (model 1850 only) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts and lever operated pop-up wastes. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of three hole, metal, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Range of wall mounted bath spout outlets incorporating (brass bodies - various finishes) with a plastic aerator. The product can also be supplied with a pop-up waste – not verified by test (see models). Open outlet use only. Maximum operating temperature 65.0°C
Range of water filters with a plastic body and plastic filter. The products are supplied with a spherical valve, which acts as a drain valve. This is provided loose for the installer to attach, or for models added July 2025 it can also be factory applied. Maximum working pressure 6.0 bar. Cold water use only.
Range of filter shower handsets and tap outlets with plastic bodies with EPDM O-Rings Open Outlet use. Maximum operating temperature 60°C
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘EPH_WSP19_XXXX’ range of brass caplillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Flowflex,’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
CORE “SB DZRCOM” range of DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The tank connectors incorporate a NBR gasket. The straight tap connectors incorporate a blue fibre gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Instantor Lead-Free Brass’ compression fittings with DZR brass body, for use with DZR Copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Twistloc’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
‘EPH_WSP19_XXXX’ range of brass end feed and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of counter-top or under-sink electrical water heaters. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C, except 65°C for 10L models.
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.
‘WS’ range of water meters with brass bodies, incorporating plastic impellers. The inlets incorporate plastic filters. Maximum working pressure 16 Bar. Maximum operating temperature 50°C.
Range of water meters with plastic bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of water meters with black nylon bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of combination valves with bronze bodies, incorporating a spherical valve with a brass ball on the inlet, two pressure gauges either side of a pressure reducing valve and a water meter manifold. The pressure reducing valve has an outlet pressure range between 1.5 and 6.0 bar. The outlet incorporates two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). The outlet of the Easy Flow Pro model also incorporates a spherical valve with a brass ball and a combined drain valve, above ground use only. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.
Range of bidet spray kits, wall outlet and brackets with brass bodies (various finishes), bidet spray kits consist of a wall outlet bracket, double interlocking flexible hose and a handset with self-closing trigger mechanism. Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
Range of angled valves with chromium plated brass bodies, incorporating a non-rising spindle headwork or a quarter turn ceramic disc headwork with either triangle, cubic, single lever or dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of multistage pumps with stainless steel bodies and impellers. Maximum working pressure 10.0 bar. Cold Water Use Only.
Range of shower handsets and overhead showers with plastic bodies incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
A12231 & A12011 Ranges of shower handsets with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. Maximum operating temperature 65°C.
Range of shower handsets and overhead showers with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 980505CPVR | Chrome | 1/2 BSP | bar | 65 °C | Bristan | Shower Rose | No | Not applicable | Not Applicable | Not Applicable |
Range of (chrome plated) plastic shower handsets, each supplied with five (optional) plastic flow regulators (x2 blue, light green, dark green and grey). Maximum operating temperature 60°C.
Shower handset with plastic body (various finishes) incorporating EPDM ‘O’-rings and washers. Maximum operating temperature 65°C.
Range of overhead shower outlets (ABS plastic - various finishes), incorporating a stainless-steel strainer. Open outlet use only Maximum operating temperature 60.0°C.
Range of wall or ceiling mounted shower outlets with chromium plated bodies (or black body for 22123KF0) consisting of showers arms and shower head for installation with specific rough-in sets. Shower head bodies incorporate approved single check valve cartridges, however, the complete assemblies have not been tested to demonstrate it provides backflow protection. The 26.484 model rough-in set incorporates a plastic flow regulator on the inlet. Maximum working pressure: Open Outlet. Maximum operating temperature: 60°C.
Range of ‘Y’-pattern strainers with a DZR brass body, stainless-steel strainer and PTFE gasket. Maximum operating pressure 20.0 bar. BS6920 85°C.
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of flanged ‘Y’-patterned strainers incorporating ductile iron, blue epoxy powder coated bodies and stainless-steel strainers. Series 11.000M incorporates a magnet rod. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of Y-patterned strainers with brass bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Wall mounted hose union taps with brass bodies, incorporating a rising spindle headwork with a ‘T’ type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HOU 1/2 C | Chrome | 1/2" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| HOU 3/4 C | Chrome | 3/4" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| RP3 HOU 1/2 C | Chrome | 1/2" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| RP3 HOU 3/4 C | Chrome | 3/4" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator |
Range of pillar taps with brass bodies (various finishes), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic flow straighteners and the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of pillar taps, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Self-closing basin tap (chromium plated brass) incorporating spring loaded headwork with dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of stainless steel braided EPDM lined flexible hose assemblies with EPDM seals & EPDM washers, available with a variety of end connections. For use with copper pipe manufactured to EN1057 & HEP20 PB pipe. Maximum working pressure; 6 Bar Maximum operating temperature; 65°c
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VA SHXSMFF C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Not Applicable | Shower Hose, Handset, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313963 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 309644 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| AR3 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313960 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| DEL SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286569 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285401 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286565 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286566 | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286567 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285400 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313962 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313965 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BB | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BLK | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311671 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311672 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311673 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 231844 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313961 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV GM | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCVO C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 SAI SHCDIV C | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Model added February 2026: RP3 SAI SHCDIV C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OP TS3650 CL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | |
| OP TS3650 EL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | |
| OP TS3650TO EL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH60 | Brass | 1/2" BSP (M) | 10 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E80017 | Chrome | 15mm Compression | 10 bar | 60 °C | esteem | handle | No | Single sequential | Metal Backnuts | Not Applicable | Shower Hose, Riser Rail, |
Range of concealed, thermostatic blending valves with 2 or 3 shower outlets, incorporating a thermostatic cartridge controlling the temperature that incorporates a manual override button and ceramic disc diverters or quarter turn ceramic disc headworks controlling the flow. The products incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed thermostatic blending valves (brass bodies – various trim sets and finishes) with ceramic diverter controlling the flow which also diverts to 2 or 3 outlets and a thermostatic cartridge controlling the temperature independently. The inlets incorporate an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset not supplied. Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
Range of wall mounted thermostatic bar shower mixers (chrome plated brass) incorporating quarter turn ceramic disc headwork with single lever type operating members. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. Both inlets incorporate stainless steel strainers and approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with a show hose, handset and riser rail assembly. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 190JK | Chrome | 15mm Compression | 10 bar | 60 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
Range of wall mounted self-closing thermostatic shower valves with brass bodies, with a chrome plated dome type operating member. Models are also supplied with a chrome plated shower head with a plastic aerator. Both inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Wall mounted, thermostatic shower valve (chromium plated brass) for use with copper pipe (manufactured to BS EN 1057). The flow is controlled by a quarter turn ceramic disc headwork with either a dome or lever type operating member. The temperature is controlled by a thermostatic cartridge with either a dome or lever type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of concealed thermostatic shower valves, (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork controlling the flow to the shower outlets. Model VQ15 and VQ16 incorporates a manual diverter to the outlets. Model VQ20 incorporates a single shower outlet and model VQ21 incorporates a double shower outlet. The temperature is controlled independently via a thermostatic cartridge. The inlets incorporate approved single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, thermostatic shower valves, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with dome type operating members, the inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and a stainless-steel strainer. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Shower set comprising of a wall mounted shower valve, riser rail, shower handset, shower hose and overhead shower outlet. Flow in controlled by a ceramic disc headwork with dome type operating member. Temperature is controlled via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Each inlet of the shower valve incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of gear operated butterfly valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16 Bar Maximum operating temperature 80°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with (blue epoxy coated) ductile iron bodies and cast iron discs incorporating EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Angled flow control valve with chromium plated brass body, incorporating a non-rising spindle headworks with dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Angled flow control valves with chromium plated brass bodies, incorporating non-rising spindle headworks with dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of non-return, swing gate valves DZR brass and DZR brass discs. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Manually adjustable pressure reducing valve with nickel plated, DZR brass body for use with copper pipe (manufactured to EN1057). Maximum supply pressure 16.0 bar. Outlet pressure range between 1.0 & 6.0 bar. Factory pre-set at 3 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with DZR brass bodies (CW602N or CW511L), EPDM ‘O’-rings and a stainless steel strainer. Available with a variety of end connections (see model). Models with compression, pressfit and pushfit connections are for use with copper pipe. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 80°C.
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. 447 70 models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. Maximum operating temperature 60°C.
Range of normally closed (NC), solenoid valves with plastic bodies and EPDM diaphragm. Models with push-fit connections are for use with copper pipe (manufactured to EN 1057) and PTFE pipe. The products incorporate a plastic or stainless steel filter on the inlet, (except for models with swivel nut, push-fit and nozzle inlets, as well as the 44.007.126 and 01.021.126 models) . The 44.007.126 model incorporates a Y-pattern stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperatures: Cold water use only, 65°C or 90°C for models marked with ℗ - Please consult model section for further details.
Ranges of solenoid valves with plastic bodies and stainless steel strainer. Models with female connections incorporate a stainless steel threaded connector. Maximum working pressure 10 bar. Maximum operating temperature 70°C.
Dual outlet solenoid valve with a plastic body, incorporating EPDM diaphragm and ‘O’-rings. The inlet incorporates a plastic flow regulator and a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of push fit lever operated spherical valves incorporating brass bodies and brass ball (various finishes). Products to be used with PEX pipe (manufactured to BS7291 part 3), Polybutylene Pipe (manufactured to BS7291 Part 2) and copper pipe (manufactured to EN1057) Maximum working pressure 6.0 bar (for PEX and Polybutylene pipe). Maximum working pressure of 20.0 bar (for copper pipe). Maximum operating temperature: 95°C.
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
‘KBGR16’ range of gate valves with either brass or DZR brass bodies and PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. DN50 to DN500 sizes are operated by handwheel. DN600 to DN800 sizes are operated by a gear box. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Screw down angle valves (chromium plated brass) incorporating a dome (triangular) type operating member with a NBR rubber washer. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Magnetic scale reducer, incorporating chrome plated copper body, for use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
'KH369AC'. Dark grey coloured, compression moulded carbon/graphite ring. For use with water up to 85°C.
'NM 96 & NM 99 Ceramic Discs'. Off-white coloured, compression moulded ceramic discs. For use with water up to 85°C.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TP1'. Factory applied, colourless solid lubricant. Apply as per manufacturer's instructions 'LDAP-005', issue 1, dated 11/11/2016. For use with water up to 85°C.
'RADILON® S RV350RKC2 306 BK'. Black coloured, injection moulded, 35% glass fibre reinforced, PA6 material. For use with water up to 85°C.
'1EP6052'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.12mm. For use with water up to 23°C.
‘51M5577, 51M6077, 51M6577, 51M7077, 51M7577, 51M8077, 51M8577’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘40SIL310P, 45SIL310P, 50SIL310P(W), 55SIL310P, 60SIL3137P, 65SIL310P, 70SIL310P, 75SIL310P & 80SIL310P'. Compression moulded, silicone rubber ‘O’ rings in natural, white, black, red, blue, yellow & grey. Tested in-radius size 0.5mm. For use with water up to 85°C.
'Lettergold External Leak Sealer'. Clear silicone sealant. Apply as per manufacturer's TDS 'Version 1', dated '16/07/2025'. Cure for 96 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE 680'. Green coloured (translucent), anaerobic adhesive. Apply as per manufacturer's TDS 'Reference 1.5', dated 'August-2016'. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Weld-On 748 ECO™ Blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer’s TDS ‘748 ECO-09-2024’. ‘Weld-On 748 ECO™ Clear PVC Solvent Cement’ was added to the approval in March 2026. Clear solvent cement. Apply as per manufacturer’s TDS '748 ECO-07-2025'. Cure for 12 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Grilamid TR 30 natural, TR 30 LS natural (appear colourless, translucent), TR 30 LS blue 4345, TR 30 LS blue 4387 & TR 30 LS blue 4396 (blue coloured)’. Injection moulded, PA 61/X materials. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193745 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 65 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 Bar. Cold water use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 440 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 71 450 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HNHS40-Black | Various | 1/2" F | Open Outlet bar | 65 °C | Waterworks logo | Shower handset | No | None | Shower Hose, Handset, | ||
| HNHS40-Grey | Various | 1/2" | Open Outlet bar | 65 °C | Waterworks Logo | Shower Handset | No | Shower Hose, Handset, |
Finishes Available - Brass, Chrome, Nickel, Burnished Brass, Matte Nickel, Brass/Dark Nickel, Copper, Dark Brass, Dark Nickel, Vintage Brass, Gold, Matte Gold
Range of hand showers and shower arm kits with (brass bodies - various finishes. The inlets of the hand showers and the inlet elbows incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Open outlet use only. Maximum operating temperature 65°C.
Range of wall mounted shower valves (brass bodies – various finishes) incorporating a self-cancelling diverter with a ceramic cartridge headwork controlling flow and temperature and a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH72 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH73 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH62 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH63 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable |
Product Identification(s) with an * as suffix = models added 11/08/2025
Range of Type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) and flexible hose. Flow is controlled via a solenoid valve. Both inlet and outlets incorporate flow restrictor. Maximum working pressure 6.0 Bar Maximum operating temperature 60.0°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of In-line plastic flow regulators housed within a brass bodies incorporating a plastic strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Range of deck mounted ceramic cartridge and single sequential headwork assemblies, (brass bodies – various styles and finishes), incorporating a range of operating members. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Thermostatic cartridges incorporating plastic bodies, for insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AB-2047-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2053-F | 33.6 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2057-F | 26.8 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-F | 27.5 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-S | 27.2 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2059-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No |
Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet is a waterfall type and incorporates a stainless steel mesh at the spout. Maximum working Pressure 10.0 bar. Maximum operating temperature 65ºC.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T21002L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T50802L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T10102 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Filter | |
| SL-T20402 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T40202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| SL-T40102W | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | C-plate | Flow Straightener |
Various finish: (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass (4) Models SL-T40202 & SL-T40102W with suffix G: Champagne Gold
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AL ES BAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CRU TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313935 | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313936 | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313937 | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
Combination Tap assemblies incorporating ceramic cartridge or ceramic disc headworks.
Single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a quarter turn ceramic disc headworks and single lever operating members, with a pull out spray retained within a holster. The spout outlet incorporates a plastic aerator and the spout incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (swivel) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with a brass body (chromium plated brass), incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (plated brass), incorporating ceramic cartridge headwork with dome type operating member, located at the end of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC DFBAS C MT | Chrome | G 1/2 | 5.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet | Pop Up |
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic disc headwork (GE08) or non rising spindle headwork (CR26) with single lever and cross top operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
The model without a suffix indicates chrome. The model number with suffix B indicates black. The model number with suffix BB indicates Brushed brass.
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headwork with single lever type operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic aerator and the product is also supplied with a shower handset and hose. The inlet of the shower handset incorporates a plastic flow regulator. The product is supplied with either plastic or metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves (plated brass bodies), incorporating ceramic disc headworks controlling the flow and a thermostatic cartridge independently controlling the temperature, both using dome type operating members. Both inlets incorporate single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides adequate backflow protection) and metal strainers. Spout outlets incorporate plastic flow straighteners. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| LIS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| LIS BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| RP3 LIS BSM C | Chrome (Cr3) | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| RP3 ELE BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Shower Hose, Handset, |
Model added February 2026: RP3 ELE BSM C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21001 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T31501 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T50801 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T30601W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T20401 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T40201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40401R | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40101W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T10101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
Range of two-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar Maximum operating temperature 65°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (DZR brass main body - various finishes) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HD15 | Chrome | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15K | Matte Black | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BB PVD | Zirconium gold brushed topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BV | Brushed gold matte topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15MG | Gun gray brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15CA | Rose gold brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BN | Nickel brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
These models only different in surface treatment
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313941 | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313942 | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313943 | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
Range of three-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlets incorporate plastic aerators. The products incorporate stainless steel braided, silicone rubber (TPSiV) lined inter-connecting hoses. The products are supplied with metal back nuts and click type pop-up wastes (not verified by test). Maximum working pressure: 6.0 Bar. Maximum operating temperature: 65°C.
Range of plastic filter heads and housings. Maximum working pressure 8.6 bar. Cold water use only.
‘GM50xx’ range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *- STPT304 and *- STPT316 stainless steel pipes. The GM5004 prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
‘Uponor Q&E’ range of brass press-fit fittings for use with PE-Xa-PE-PE ‘Uponor Aqua Pipe AU’ multi-layered pipes. Maximum operating pressure 10 bar. Maximum operating temperature 70°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with MONFLEX PEXB/AL/PEXB MULTILAYER PIPES. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Mingshi stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Hyddro Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Hyddro stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of compression fittings with brass, chrome plated brass bodies. COM RANGE OF COM For use with copper pipe (EN 1057) Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of brass press fittings for use with copper pipe (manufactured to EN1057:2006 and +A1:2010 Seamless round copper tube, R250 half hard). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘AF’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Range of WC dual flush drop valves with ABS bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
Range of urinal autosyphons with plastic body and supplied with plastic backnuts.
Range of SSM-AQUO ultrasonic water meters with brass bodies, the inlets incorporate a plastic filter. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of pilot operated base valves, main body only, with epoxy coated ductile iron bodies and stainless-steel plugs. Maximum working pressure IDROMEMBRANA 16.0 & HYDROMODUL 25.0 Bar Maximum operating temperature IDROMEMBRANA 50.0°C and HYDROMODUL 80.0°C.
’TP Series 300’ and ‘TPE Series 300’ ranges of single stage in-line pumps with black coloured cataphoretic electro deposition coated cast iron or ductile iron bodies and bronze, stainless-steel or black coloured cataphoretic electro deposition coated cast iron impellers. Pumps are available with BQQE or BBQE shaft seals. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O` rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Maximum operating pressure 3.8 bar. Maximum operating temperature 65°C.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless-steel filter and a plastic flow regulator. Maximum working temperature 45°C. Open outlet use only.
Shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
Shower handset with a plastic body and Chrome finish Maximum operating temperature 60 °C. Open outlet use only.
Range of ‘Y’-pattern strainers with blue epoxy coated ductile iron bodies and a stainless-steel screen. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps ( brass body - various finishes, see), CR20 and CR20/501 incorporate a non-rising spindle headworks with a dome type operating member. GE02 and GE02/201 incorporating quarter turn ceramic discs headworks with a lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Pillar taps with brass body chrome finish, incorporating quarter turn ceramic disc headwork with single lever operating members. The product is supplied with metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
410714 Modena & 161633 Kubic ranges of pillar taps (brass bodies – Chrome finish) incorporating a quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar, Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T40217 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40218 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40217W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40218W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40107W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T41107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T41108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40807W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40807 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42106 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40106W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Aerator |
1. Various finish: (1) With suffix B: Black (2) With suffix BB: Brushed brass (3) Models SL-T40217, SL-T40218, SL-T40107W, SL-T40108W & SL-T40106W, with suffix G: Champagne Gold
Range of wall mounted self-closing taps (chromium plated brass) with a dome type operating member. The SCHELL PETIT SC - 02 147 06 99 model incorporates a screwdriver operated servicing valve on the inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Range of self-closing taps (chromium plated brass) incorporating spring loaded headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. The products are supplied with a metal back nut. Maximum working pressure 3 bar. Maximum operating temperature 65°C
HOS wwwxxyy z - Range of EPDM or PVC lined, interlocked stainless-steel shower hoses. Open outlet use only. Hoses with an EPDM liner have a maximum operating temperature of 85°C. Hoses with an PVC liner have a maximum operating temperature of 65°C.
Multi-layer PVC shower hoses with Black, Brushed Brass or Chrome finish with brass end connections, EPDM gasket and NBR ‘O’-ring. Open outlet use only. Maximum operating temperature 65°C
Range of EPDM hoses with either nylon or stainless-steel braiding, with or without a PVC sheath. Some models incorporate isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of wall mounted, concealed, thermostatic shower valves, (brass bodies - various trim set finishes), incorporating quarter turn ceramic disc headwork with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The products incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate that is provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic blending valves with brass bodies (various finishes). Incorporating either 2-way ceramic disc diverters (2 on, 1 off) that also controls the flow (model DB3100.a.bbb) or with a ceramic disc headwork that controls the flow only to a single outlet (model DB3200.a.bbb.). Both incorporate lever type operating members. The temperature is controlled independently via a thermostatic cartridge with lever type operating members. Inlets incorporate approved check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of thermostatic mixing valves in various finishes, model XX3001YY has one outlet, temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc valve, model XX3002YY has 2 outlets temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc cartridge and model XX3003YY has 3 outlets temperature is controlled independently by a thermostatic cartridge and the flow controlled via a ceramic disc cartridge. Inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Range of Shower Valves with thermostatic temperature control. Wall Mounted Concealed. Inlets incorporate approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum temperature 85°C Miximum pressure 5.0bar.
Range of wall mounted, thermostatic shower valves (brass body – various finishes), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Wall mounted, thermostatic bar shower mixer (chrome plated brass body) incorporating a quarter turn ceramic disc headwork with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is supplied shower hose, handset and riser rail assembly Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Range of lugged butterfly valves with blue epoxy coated ductile iron bodies and nickel plated, ductile iron discs. LWBV-K models are lever operated, the LWBV-3K are handwheel operated. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of tilting disc non-return valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range lever operated spherical valves with nickel plated brass bodies and chromium plated brass balls. The 1792 model compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Lever operated spherical valve with a chrome plated brass body and ball. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of angled spherical valves with chromium plated brass bodies and ball. The AGV1734 model is lever operated, the AGV1834 model has a ‘T’-handle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies (chromium plated), chromium plated brass balls, PTFE seat and single lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves, brass body and disc with a handwheel operating member. Maximum working pressure 20.0bar Maximum operating temperature 100°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Angled servicing valves with chrome plated brass bodies incorporating dome type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'SH Special Seal grease'. Opaque, white coloured silicone grease. Apply as per manufacturer's instructions. No cure required. For use with water up to 65°C.
'SILICOMPOUND FCA 125'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Badadur PBT9 GF30 graphit 371 (grey coloured) & Badadur PBT9 GF30 Alpinweiss 230c (white coloured). Injection moulded Polybutylene terephthalate (30% glass fibres) materials. For use with water up to 65°C.
'Fox Spigot and Electrofusion Fittings'. Black coloured, injection moulded polyethylene spigot and electrofusion fittings. For use with water up to 65°C.
'PE002'. Blue coloured, extruded HDPE pipe. For use with water up to 60°C.
'aquatherm PE-RT pipe'. Off-white coloured, extruded PE-RT (Type 1) pipe. For use with water up to 65°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
‘RIALENE P 100 SGFxx KTW grau K 7-128, RIALENE P 100 SGFxx KTW weiß K 9-112, RIALENE P 100 SGFxx KTW schwarz’, injection moulded polypropylene materials available in grey, white and black. ‘RIALENE P 100 SGFxx KTW natur(al)’, natural (appears off-white), injection moulded, polypropylene material was added to the approval in February 2026. The ‘xx’ in the material name can be replaced with any number between ‘10’ and ‘50’. For use with water up to 85°C.
'HC-EP7001165PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51M6767'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
'51M5567'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 0.5mm. For use with water up to 23°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'TWK3628'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'Loxeal 85-86'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'ONEBOND ADHESIVO PVC PROFESIONAL'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BLAZEMASTER® 88065 Orange 734 M PEL 8065OMAM'. Orange coloured, injection moulded c-PVC fittings. For use with water up to 23°C.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 98°C. Hot-water circuit has a maximum operating temperature of 65°C.
Range of deck mounted two hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating a ceramic disc headwork controlling the flow with a dome type operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. The spout outlet incorporates a plastic aerator. Models SHTLV106/1B & SHTLV106/2BK are supplied with a shower hose & shower handset and riser rail. Model TLV106 is supplied with a shower hose & shower handset. All models are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes), incorporating a ceramic disc headwork controlling the flow with a dome type operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. The spout outlet incorporates a plastic aerator. All models are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH71 | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | |||
| GUTH61 * | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk |
Product Identification with an * as suffix = models added 11/082025
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM 3WDIV C | Chrome | 15mm Compression | 10 bar | 60 °C | Bristan | Faceplate | No | Not applicable | Not Applicable | Not Applicable |
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies models HVDCVC-31, HVDCVC-32 are chrome plated. Maximum working pressure 16 Bar Maximum operating temperature 60°C
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel nozzle) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Some models incorporate a stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 812003A | 23.8mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812038A | 23.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812049A | 19mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812056 | 18.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812057 | 19.0mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812072 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812073 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812114 | 18.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TM001 | Black | Ø 33.81mm | 5 bar | 85 °C | Company logo and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable | |
| TM006 | Black | Ø 26.66mm | 5 bar | 85 °C | Company logo, Sedal and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable |
Single hole, single outlet (swivel) combination tap assembly with white finish brass body), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headworks with a cross top operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 233308 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 Bar Maximum operating temperature: 65°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies -various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0Bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQSOL EFSNK C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 4648G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288489 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288491 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311098 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 3311102 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311106 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311162 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQMEN EFSNK BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 9087G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288493 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288503 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311105 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311114 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311125 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311164 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | C-plate |
Model added February 2026: RP3 EC SNK EF BLK
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes) incorporating 1/4 turn ceramic disk headworks and single lever operating members. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 147013 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | Non-rising spindle | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| QST SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| RP3 DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disc | C-plate | Flow Straightener |
Model added February 2026: RP3 DUL SNK EF C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating either a ceramic cartridge headwork or quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator (LEV104 and FARO104 models) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (swivel) combination tap assembly (brass body – various finishes), incorporating two ceramic cartridge headworks with single lever operating members, with the upper headwork functioning as a manual diverter, diverting flow between the spout outlet and shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure: 10 Bar. Maximum operating temperature 65°C.
Range of single hole, double outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever or non-rising spindle headworks with cross top operating members (see model). The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with cross top operating members. The product is supplied with metal backnuts. Maximum temperature 60°C Maximum Pressure 10 bar
A deck mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members, the spout incorporates a flow straightener. The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet either incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes, brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes brass bodies), incorporating quarter turn ceramic disc headworks with various operating members (see models). The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 34 113 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 115 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 112 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 116 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish. Products to be installed in combination with 13623180 Basic set, which does not form part of this approval.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with metal backnuts. Maximum working pressure: 5 Bar Maximum operating temperature: 65°C.
Range of wall mounted, two-hole single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 Bar Maximum operating temperature: 65°c
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AR2 THLBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| BRT AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| CN AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disc | Metal Backnuts | Flow Straightener |
Model added February 2026: RP3 AR2 THBSM C
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a two-way diverter headwork that controls the flow between the spout outlet and shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic mixing cartridge, the incorporates a manual override button. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5 bar.
Non-metallic materials and components comply with BS6920 at 65°C
GE03, GE03/501, CR23 & CR23/501 Range of two hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn ceramic disc headworks with single lever or cross-top operating members and manual diverters to shower outlets. The spout outlets incorporate plastic flow straighteners. This approval includes a hose & handset and the products are supplied with metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks with either single lever or cross top (L-BS model) operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks with cross top operating members and manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (various finishes, brass bodies), incorporating quarter turn ceramic disc or ceramic cartridge headworks single lever or cross top operating members (see models) and a manual diverter to shower outlet. The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever or cross top operating members (see models) and a manual diverter to shower outlet. The spout outlet either incorporates a plastic flow straightener or an open outlet (see models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FRZ BSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
Range of three hole, wall mounted, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model) comprising of a spout outlet, a clipsed extension set for accommodating headworks and a trim set with various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH WMBAS C | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 3TH WMBAS BLK | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 3TH WMBAS BB | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS C | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS BLK | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS BB | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313938 | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313939 | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313940 | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH WMBF C | Chrome | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| AL 3TH WMBF BLK | Black | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| AL 3TH WMBF BB | Brushed Brass | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF C | Chrome | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF BLK | Black | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF BB | Brushed Brass | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
Range of three-hole, brass bodied, single outlet (fixed) combination tap assemblies available with various finishes (see models). The products incorporate either a non-rising spindle (models 1648 and 1881 only) or quarter turn ceramic disc (all other models) headworks with either cross top (models 1648 and 1881 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts and lever operated pop-up wastes. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 11 430 xx0 | Various | G 3/4 | open outlet bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of Hyddro press fittings incorporating EPDM ‘O’-rings. For use with Hyddro (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
‘ISR’ range of copper, DZR brass or gunmetal capillary, lead free solder ring and threaded fittings for use with copper pipe. (Products YP62, YP63, YP63L, YP64, YP68, YP68FF, YP69, YP69F & YP69P Maximum working pressure - 16 bar Maximum operating temperature - 65C All other fittings Maximum working pressure - 16 Bar Maximum operating temperature - 95°C.
‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of Victaulic rigid couplings (905, H10, H11, H20, H50) for use with plain end HDPE pipe (EN 12201-2), and for product 907, for use with EN 12201-2 HDPE and EN 10217-1 steel pipe. For above and below ground use. Maximum working pressure: SDR7.4 25bar, SDR11 16bar or SDR17 10bar. Maximum operating temperature: Cold water use only.
Range of polypropylene push-fit fittings and inserts for use with PE80 MDPE pipe (manufactured to BS EN 12201). For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of metric and imperial PVC-U Solvent cement or Threaded fittings for use with PVC-U pressure pipe Class E manufacture to BS EN 1452 Maximum working pressure; 16 Bar Maximum operating temperature; Cold water only
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure: 16 Bar. Maximum operating temperature: 65°C.
Range of blue epoxy coated ductile iron flanged dismantling fittings. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of water meters with plastic bodies, incorporating stainless steel pipe section. Maximum working pressure 16.0 bar. Maximum operating temperature 23.0°C
AQUAPRO range of angled valves with chromium plated brass bodies, incorporating a non-rising spindle headwork or a quarter turn ceramic disc headwork with either cubic, single lever or dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Impeller with plastic body for insertion into specifically dimensioned bores. Maximum operating temperature 65°C.
Range of pressure transmitters gauge pressure measurement devices and differential pressure measurement devices with either stainless steel or Hastelloy or Monel bodies. Maximum working pressure 66.0 Bar Maximum operating temperature 85.0°C
Range of threaded copper pipe elbow tap unions. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The DPV(M/S) models and DPV(S) models can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Existing models: DPV models 10.0 bar, DPVM models with an oval flange or VME models with integral check valve 16.0 bar, All other DPVM models 25.0 bar. DPV(S) models with an oval flange or DPV(S)(E) models with integral check valve 16.0 bar, All other DPV(S) models and DPH(S)I models 25.0 bar. Maximum operating temperatures: DPHM, DPVE and DPVME models with integral check valve 60°C, all other model variants 100°C.
Range of interlocked EPDM lined shower hoses assemblies with EPDM gaskets. Maximum operating temperature: 85°C Open outlet use only.
Range of shower handsets and headsets with chromium plated plastic bodies. Models P60901 and P61400 have check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum working pressure: Open outlet. Maximum operating temperature: 60.0°C.
Range of fixed shower arms, (brass bodies - various finishes) with EPDM O-Rings. Maximum operating temperature: 85°C, open outlet use only.
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of in-line blue epoxy coated ductile iron bodies with a stainless steel filter. Maximum working pressure: 16 Bar. Maximum operating temperature: 65°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Wall mounted hose union bib taps incorporating a rising spindle headwork with a T - handle operating member. With brass body incorporating a lockshield device at the base of the operating stem. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
CR27A Chrome Pillar tap with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. The spout incorporates a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
GE01, GE01/501, CR19 & CR19/501 Pillar taps with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. Models GE01 & GE01/501 incorporate a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Softpex® Range of Stainless Steel and Polyamide braided, PE lined connection hoses with various end connections DN6 (S/S & PA braided – PE-RT) , DN8 (S/S & PA braided – PEX), DN10 (S/S braided - PEX ONLY), DN13 (S/S braided - PEX ONLY) Maximum working pressure; 10 Bar Maximum operating temperature; 70°c
Range of air venting valves with epoxy coated ductile iron bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 65°C.
Range of air venting valves with blue epoxy coated ductile iron or plastic bodies with plastic floats. Maximum working pressure 16.0 Bar. Cold water use only.
Range of automatic air release valves with blue epoxy coated stainless steel bodies and plastic or stainless-steel floats. Maximum working pressure 16.0, 25.0 or 40.0 bar (See Models below). Cold water use only.
Range of wall mounted, concealed, manually operated blending valves with (brass bodies - various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks and single lever or dome type operating members. Maximum working pressure 5.0 Bar Maximum operating temperature 70 °C.
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating a 2-way manual diverter to control the flow with cube type operating members. The temperature is controlled independently via a thermostatic cartridge with cube type operating member that incorporates a manual override button. The inlets incorporate stainless-steel strainer and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted bar type thermostatic shower valves (chrome plated brass bodies) incorporating ceramic disc headwork which controls the flow with cubed type operating members. Temperature is controlled independently via a thermostatic cartridge with cubed type operating member that incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Wall mounted thermostatic shower valve (chromium plated brass) incorporating a quarter turn ceramic disc headworks with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with manual override button and a single lever operating member. Both inlets incorporate an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless steel (CF8M) discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gear operated butterfly valves with blue epoxy coated ductile iron bodies and discs, incorporating hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer and lug butterfly valves incorporating blue epoxy coated ductile iron body, either a stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron disc and an EPDM seat. DN40-300 lever and gear operated, DN350-600 gear operated. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of flow control valves with blue epoxy coated ductile iron bodies. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 65°C
Range of angle valves (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork with single lever operating members. Maximum working pressure 5.0 Bar, Maximum operating temperature 60.0°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return valves with ductile iron bodies and discs. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 65°C.
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
UNIWAT 5107Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies. Maximum inlet supply pressure 8.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of single lever or butterfly handle operated spherical valves with chrome plated brass bodies incorporating chrome plated brass ball. Maximum working pressures: see model below. Maximum operating temperature 23°C.
Range of spherical valves with brass bodies, stainless steel (SS304) balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, chrome plated ball and PTFE seats. Not supplied with operating member. Maximum working pressure 25.0 Bar Maximum operating temperature 90 °C.
Range of DZR brass isolation valves incorporating a chrome plated brass ball and PTFE seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of ‘EFFAST’ spherical valves with plastic bodies incorporating EPDM ‘O’-rings. For use with ABS pipe manufactured to BS 5391. Maximum working pressure: 15 Bar. Maximum operating temperature: Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with DZR brass or brass bodies, incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
GAER S12 Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
GAER S12 Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with brass bodies, incorporating a brass wedge. Valves are operated via a non-rising spindle headwork incorporating either a lockshield or handwheel operating member. Maximum working pressure 20.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with pipe connector and flange adapter systems with ductile blue epoxy coated bodies, EDPM wedge and PTFE gaskets. The valves operate via a hand wheel. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies, brass discs and stems. The valves operate via a non-rising spindle and are supplied with a wheel type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's Work Instructions 'WP-08-05 I', Issue '04', Revision '0', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PLUSTEK PA100NT-F'. Cream coloured, injection moulded PA66 material. For use with water up to 85°C.
'ESTAMID 66 G6 HS HR NATURALE'. Natural (appears off-white), injection moulded, glass fibre reinforced PA 66 material. For use with water up to 85°C.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'Sangir Pipes'. Black coloured and blue coloured, extruded HDPE pipes. For use with water up to 65°C.
'Sangir Fittings'. Black coloured and blue coloured HDPE fittings. Blue coloured Fabricated Fittings (Extrusion Process+ Butt fusion Welding) and Injection moulded EF Fittings are for use with water up to 23°C. Blue coloured Injection moulded fittings are for use with water up to 65°C. Black coloured Injection moulded, Fabricated (Extrusion Process+ Butt fusion Welding) & Injection moulded EF Fittings are for use with water up to 65°C.
'Rainson PPR material'. Green coloured, injection moulded PPR material. For use with water up to 65°C.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP PURE EPOXY RESIN JF375E'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins, available in light pink or grey colours. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0011’, dated ‘30/01/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 17/0011’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'B8066'. Black coloured, compression moulded Chlorobutyl rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AP-EPDM 50A, AP-EPDM 60A, AP-EPDM 70A & AP-EPDM 80A'. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 80A. Tested in-radius size between 1.15mm & 1.21mm. For use with water up to 65°C.
'EP 70110 HC'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.56mm. For use with water up to 23°C.
'Cura External Leak Sealer (Part No: 27813)'. Clear silicone sealant. Apply as per manufacturer's TDS 'Version 1', dated '16/07/2025'. Cure for 96 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 Bar Maximum operating temperature 65.0°C
Range of bottom entry BS1212-4 (2016) delayed or non delayed action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush and reduced flush. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Wall hung concealed WC flushing cistern with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Low Level WC suites incorporating a frame mounted ceramic pan that is fitted with a washing & drying arrangement which is fed via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The cistern incorporates a side entry BS1212/4 float operated inlet valve and provides a type `AB` air gap. The drop type flush valve provides a single flush of 6 litres and is operated by elbow push button levers that are designed into the front of the cistern cover. Maximum working pressure 10.0 bar. Cold water use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OASISBM | Chrome | 1/2" BSP (F) | 8 bar | 65 °C | Utopia | Body | No | Solenoid | Not Applicable | Aerator |
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator. The products are supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Non-verifiable double check valve assemblies with DZR brass or chrome plated DZR brass body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30D-9 | 29.91mm | 10 bar | 85 °C | WANHAI, WRAS, 30D-9, Production date (DD/MM/YYYY) | Body | No |
Single hole, single outlet (swivel) pull down spray combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various styles and finishes) incorporating ceramic cartridge headworks, and single lever operating members. The spout outlets incorporate a plastic or metal aerator. The products are supplied with click type pop-up wastes (not verified by test). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination tap assembly ( brass bodies - Chrome finish), incorporating a ceramic disc headworks with cross top operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener. Supplied with a click type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating members. The spout outlet incorporates a plastic flow aerator. Maximum working pressure Bar 10.0 Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B002* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | Body | No | 1/4 Turn ceramic disk | C-plate | Aerator | |
| B003* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | Body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
* denotes finish and can be replaced by: C - Chrome, RG - Rose Gold, BTG - Brushed Titanium gold, BZG - Brushed Zirconium gold, BRG - Brushed Rose gold, MW - Matte white, BS - Brushed stainless, BN - Brushed nickel, PN - Polished nickel, GM - Gunmetal, B - Matte black, TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The inlets of the TKUBEDLXX, TKUBESLXX and TQUADDLCM/ models are supplied with a loose ½”x½” BSP (M) chrome plated brass housing. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| N SNK EF C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
Range of two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. Maximum working pressure Bar 10.0 Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B001* | Various | ½" BSP (F) | 5 bar | 65 °C | WINSDRUM | Decorative plate | No | Ceramic cartridge | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome, RG - Rose Gold, BTG - Brushed Titanium gold, BZG - Brushed Zirconium gold, BRG - Brushed Rose gold, MW - Matte white, BS - Brushed stainless, BN - Brushed nickel, PN - Polished nickel, GM - Gunmetal, B - Matte black, TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 2TH WMBAS C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BLK | Black | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BB | Brushed Brass | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
Range of two-hole, single outlet (fixed) combination tap assemblies (brass body – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| RP3 MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| HMS MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| CN SPH BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
Deck mounted, two-hole single outlet (brass bodies – various finishes), incorporating ceramic disc headwork controlling the flow from spout outlet to shower outlet and a thermostatic cartridge independently controlling the temperature, both using dome type operating members. Both inlets incorporate stainless steel strainers and approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides adequate backflow protection). The spout outlet is fitted with a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly. Incorporating quarter turn ceramic disc headworks with single lever operating members and manual diverters to shower outlets. The spout outlets incorporate plastic flow straightener. This approval includes a hose & handset and the products are supplied with metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly. Incorporating quarter turn ceramic disc headworks with single lever operating members and manual diverters to shower outlets. The spout outlets incorporate plastic flow straightener. This approval includes a hose & handset and the products are supplied with metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T41061 | Chrome plated | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/2 Turn ceramic disk | Aerator |
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – Chrome finish), incorporating quarter turn headworks with various type operating members and a manual diverter to shower outlet. The spout outlets incorporate either a plastic flow straightener or plastic aerator. Model (173605) has an open outlet type spout. The products are supplied with metal backnuts, shower hose and handset. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a two-way diverter headwork that controls the flow between the spout outlet and shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic mixing cartridge, the incorporates a manual override button. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts, shower hose, handset and flow regulator. Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), and incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Maximum temperature 60 degrees Maximum pressure 5 bar.
Range of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), and incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Maximum temperature 60 degrees Maximum pressure 5 bar.
Two-hole, single outlet (fixed) combination tap assembly (matt black finish) incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlets incorporate a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal back-nuts. Maximum temperature 65 degrees. Maximum operating pressure 10 bar.
Range of deck mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic aerator, and the product is supplied with shower hose and handset (with flow regulator) and metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M33135 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| M4305 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A, E or F – Dome, cross top or lever types Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T41001 | BSP 3/4" (F) | 10 bar | 60 °C | Company logo | On diverter cap | No | 1/4 Turn ceramic disk | Aerator | |||
| T41002 | BSP 3/4" (F) | 10 bar | 60 °C | Company logo | On diverter cap | No | 1/2 Turn ceramic disk | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8121KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8141KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H = Black 2.DYB = Matte white 3.BZ = Perl white painted 4.HGTS = Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Range of two-hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
ALT Series of wall mounted anti-ligature outlets, intended to be installed within a suitable basin (not included as part of this approval) Model ALT-81 has a single inlet & outlet and model ALT-80 has two inlets & outlets. The flow is controlled via a touch operated solenoid valve and the internal connecting pipework is pushfit. The products are for use with copper pipe (manufactured to EN 1057) and are supplied with a plastic aerator and flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
WHB, WHBV & ALS series of wall mounted, anti-ligature wash hand basins and tap outlets. The flow is controlled via a solenoid valve and the internal connecting pipework is pushfit. The WHB and ALS series can have one or two inlets, one or two outlets and the basin can have one or two piezo activated buttons. The WHBV series has two inlets, two outlets and the basin has two piezo activated buttons. The products are for use with copper pipe (manufactured to EN 1057) and are supplied with a plastic aerator and flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of cylindrical or tubular expansion vessels with epoxy coated carbon steel bodies. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C
Range of copper and bronze capillary brazed fittings for use with copper pipe manufactured to EN1057:2006 +A1:2010 Maximum pressure 10.0 Bar (54mm up to and including 108mm) Maximum pressure 2.0 Bar (Over 108mm up to and including 159mm) Maximum operating temperature 100°C.
Range of M profile copper press fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
N·U Range of stainless steel (304S31/316S11) press fittings for use with N·U series 1 & 2 stainless steel (304S31/316S11) pipe. The fittings and tube are assembled using a crimping tool. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of stainless-steel(SS304L) press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of compression fittings incorporating polypropylene bodies, plastic pipe liners, plastic grip rings and EPDM seals. For use with PE100 pipe manufactured to BS EN 12201. Maximum working pressure: 16Bar. Maximum operating temperature: 23°C
"PRESSTITE" range of press fittings with nickel plated brass bodies incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved by a TH crimping profile. For above ground use only. Maximum working pressure 10.0 bar. 20 & 26mm pressfit sizes cold water use only. Threaded and pressfit 16mm size maximum operating temperature 95°C. From June 2025: The 20 & 26mm pressfit sizes maximum operating temperature 95°C.
Range of blue epoxy coated ductile iron flanged dismantling fittings. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of dual flush WC syphons incorporating polypropylene bodies and stainless-steel C-links. Cold water use only
Range of WC dual flush drop valves with ABS bodies and silicone seals. The valves are operated via a two push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
Range of ultrasonic water meters with brass bodies and EPDM O-rings. The inlets incorporate a double check valve assembly, verified by test - suitable for backflow protection against Fluid Category 3. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic water meters with stainless steel bodies and natural rubber liners. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of ultrasonic water meters with brass/plastic bodies. The inlets incorporate plastic strainers and brass spherical ball valves. Maximum working pressure 16.0 bar. Maximum operating temperature 50⁰C.
Range of ultrasonic water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85⁰C.
Water shock absorber incorporating a stainless-steel body and EPDM membrane. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Range of heat interface units providing heating and instantaneous hot water. The central heating and hot water are generated via plate heat exchangers. The central heating circuit contains a pressure relief valve (3.0 bar) and an expansion vessel. The cold inlet supply to the plate heat exchanger incorporates an in line single check valve assembly, (suitable for backflow protection against Fluid Category 2). Max Temperature & Pressure for models A/7892284 & B/7892283: Primary Circuit: 6.0 bar at 90°C DHW Circuit: 10.0 bar at 55°C Secondary Circuit 6.0 bar at 90°C Max Temperature & Pressure for all other models: Primary Circuit: 16.0 bar at 90*C, DHW Circuit: 10.0 bar at 65*C, Secondary Circuit 3 bar at 85*C.
Range of pumps with plastic bodies, plastic impellors and either ceramic (CE suffix models) or graphite (GR suffix models) sleeves. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
A range of variable speed booster pumps with stainless steel bodies and impeller. Maximum working pressure: 8 bar. Maximum operating temperature: 35°C.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C
Range of shower arms with brass bodies. Models 91xx7034 & 91xx9323 incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 80.0°C (models 86xxxxxx) or 60.0°C (models 91xxxxxx)
Range of wall mounted shower outlets (chromium plated brass). Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of shower outlets and accessories with brass and plastic bodies (various finishes). Overhead shower inlets incorporate stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Range of (chrome plated) plastic shower handsets with flexible shower hose and stainless-steel braided connection hose. The inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C. Open outlet use only.
Shower handset with chromium plated plastic bodies with a check valve fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum working pressure: Open outlet. Maximum operating temperature: 60.0°C.
Range of flanged `Y` patterned in-line strainers with blue, black or red epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of Y-patterned strainers with brass bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain off taps incorporating DZR brass bodies and non-rising spindle operating mechanisms. D340 range incorporates lockshield mechanisms and the D341 range incorporates key operated mechanisms. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of drain off taps incorporating DZR brass bodies and non-rising spindle operating mechanisms. Fig 370 range incorporates lock-shield mechanisms and the Fig 371 range incorporates key operated mechanisms. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Pillar taps ( brass bodies – chrome finish), incorporating quarter turn ceramic disc headworks with cross top operating members. Supplied with metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of pillar taps (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure Bar 10.0 Maximum operating temperature 65°C.
Range of pillar taps (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure Bar 10.0 Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 902001 X XXX | VARIOUS | 1/2” BSP male inlet. | 10.0 bar | 85 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| 902002 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: F – Cross Top Type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic aerator and the products are supplied with metal backnuts. Model 68400 incorporates a manual temperature lever. Maximum operating pressure 10 bar. Maximum operating temperature 65°C.
Range of wall mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic aerator and the products are supplied with metal backnuts. Maximum operating pressure 10 bar. Maximum operating temperature 65°C
Range of nylon braided flexible outlet hoses, incorporating an EPDM liner, EPDM ‘O’-rings and gaskets. Maximum operating temperature 85°C.
Wall mounted shower valve (various finishes) incorporating a quarter turn ceramic disc headwork controlling flow on/off and to either the overhead shower or the handset (CAM-149T-RRK-XXX). Temperature is controlled via a thermostatic cartridge with a manual override button. The inlets incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 5bar. Maximum operating temperature: 60°C.
Wall mounted thermostatic bar type shower valves with a non-rising spindle headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a shower riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic, bar type shower valves incorporating a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is supplied with a shower hose, handset and flow regulator. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Wall mounted thermostatic bar type shower valves incorporating quarter turn ceramic disc headworks controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is supplied with shower hose, shower handset and flow regulator. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Wall mounted bar type thermostatic shower valve (chrome plated brass body) incorporating ceramic disc headworks that control flow to 2 outlets with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is supplied with a shower hose, handset and flow regulator. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E80018 | Chrome | 15mm | 5 bar | 60 °C | ESTEEM | Handle | No | Non-rising spindle | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
Range of wall mounted thermostatic mixing valves (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate servicing valves and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wafer butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The products are supplied with lever (D71X) or gear (D371X) operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
UNIWAT Range of wafer butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The products are supplied with lever or gear operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of flanged, lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of combined temperature and pressure relief valves incorporating DZR brass bodies and an EPDM diaphragm. Valves incorporate a manually operated rotational easing gear. The valves are pre-set at 6.0 or 7.0 bar (see models). Compression connections are for use with copper pipes (manufactured to EN 1057). Maximum operating temperature 90°C.
Range of combined temperature and relief valves incorporating DZR brass bodies and PTFE washers. Valves incorporate a manually operated rotational easing gear and can be supplied pre-set at 6.0 bar, 7.0 bar, 8.0 bar or 10.0 bar. Compression outlet connections are for use with copper pipe (manufactured to EN1057, R250). Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of concealed stop-valve trim sets with (brass bodies - various finishes), incorporating a quarter turn ceramic disc headwork and single lever operating member. Maximum working pressure 10.0 Bar. Maximum operating temperature 23C.
A range of non-return valve with blue epoxy coated ductile iron bodies, stainless-steel disc and EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of double swing gate, wafer, non-return valves with blue, black or red epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of adjustable in-line pressure reducing valves with bronze bodies, stainless steel strainers and manually operated pressure reducing mechanism. Outlet pressure adjustable between 1.5 to 6.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 60°C.
Pressure relief valve (pre-set to 6 bar outlet pressure) with a DZR brass body. Maximum working pressure 6.0 bar. Maximum operating temperature 75°C.
Range of normally open (L282 prefix models), normally closed (L182 models) or latching (61 suffix models) solenoid valves with either brass, nickel plated brass or stainless-steel bodies and an EPDM diaphragm. Please refer to model for maximum working pressure. Maximum operating temperature 85.0°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Angled ball valve with a DZR brass body, chromium plated brass ball, EPDM ‘O’-ring and PTFE seats. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of press fit lever operated spherical valves for use with EN1057 copper pipe, incorporating brass bodies, stainless steel ball and PTFE seats. Imperial sizes press profile is Vi and metric sizes press profile is M. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel plated DZR brass (-8511 model) or nickel plated brass (-8510 model) bodies and chromium plated brass balls. Compression connections are for use with copper pipes (manufactured to EN 1057). The product incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of in-line spherical valves with a nickel-plated brass or DZR brass body, chromium plated brass or chromium plated DZR brass or stainless-steel ball and PTFE seats (see model for details). The products can be supplied with the following operating members: 1601 and 2045 ranges: single lever, single lever with extension stem kit, single lever with lockable handle or butterfly operating members. 1046 range: short black lever or screwdriver operated. The 11-1046 (1046) and 11-1015 (2045) ranges are for use with copper pipe (manufactured to EN1057). Maximum working pressures: 1046 and 2045 range: 25.0 bar. 1601 range: 40.0 bar. Maximum operating temperature 85°C.
Range of inline plastic bodied ball valves with EPDM ‘O-rings and lever operated. For use with PVC-U pressure pipe in accordance with BS EN 1452 standard Maximum working pressure. Sizes 20mm – 63mm & 1/2" – 2”: 16.0 Bar Sizes 110mm & 2 1/2” – 4”: 10.0 Bar Cold water only
Range of bronze gate valves incorporating bronze wedges, non-rising stems. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
SD-GGV20/DZR & SD-9102 ranges of gate valves with either brass or DZR brass bodies and PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (132, 133 and 137 prefix models). Bronze body, bronze wedge and lockshield (131 and 136 prefix models). Brass body, brass wedge and handwheel (101 model only). Maximum working pressure 20.0 bar & 25.0 bar (model 131LS-50 only). Maximum operating temperature 85°C.
‘3103’ range of gate valves with either brass or DZR brass bodies and PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with a brass body and wedge. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of 2, 3 ,4 or 5 way manifolds incorporating brass bodies, stop valves and EPDM O-rings, to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Angled servicing valves with chrome plated brass bodies incorporating triangular type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (4.5, 6.0 or 8.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Monobloc manifold containing an in-line pressure reducing valve (Adjustment Range between 2.7 and 3.3 bar, but factory pre-set at 3 bar) and a pre-set expansion relief valve (pre-set pressure 6 bar) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates also a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Inlets and outlets have compression connections, for use with copper pipe to EN1057. Maximum working pressure 12 bar. Maximum operating temperature 80°C.
'KEPITAL F25-03 LOF NAT'. Natural (appears white), injection moulded POM material. For use with water up to 60°C.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Latigloss 66 H2 G/50 Nat.:0003F2 (appears beige coloured) & Latigloss 66 H2 G/50 Black:3352F2 (black coloured)'. Injection moulded PA66 materials. For use with water up to 85°C.
'TAKWEENPLAST HDPE Fittings'. Injection moulded HDPE fittings available in black or blue colours. For use with water up to 65°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'3P764921 Pipe Spacer'. White coloured (opaque), injection moulded PP Pipe Spacer. For use with water up to 85°C.
'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.
'EP60PF - EP80PF 'O' rings, gaskets & seals'. Black coloured, compression moulded EPDM 'O' rings, gaskets & seals. Shore hardness between 60 & 80. Tested in-radius size between 0.75mm & 2.66m. For use with water up to 85°C.
'51M5536'. Black coloured, injection moulded EPDM material. Shore hardness 55 ShA. Tested in-radius size 0.5mm. For use with water up to 23°C.
'WRC-70 'O' rings and gaskets'. Black coloured, injection moulded NBR rubber 'O' rings and gaskets. Tested in-radius size between 0.5mm & 2.6mm. Shore hardness 70. For use with water up to 23°C.
'VL1001P279'. Blue coloured, compression moulded silicone rubber. Shore hardness 60. Tested in-radius size 0.99mm. For use with water up to 65°C.
'CarboStop 102/CarboStop 102 ACC'. Site applied, cream coloured (once applied) waterstop. Mix CarboStop 102 resin and CarboStop 102 ACC accelerator in a weight ratio of 20:0.4. Apply and cure as per manufacturer's Application Guide, revision date '19/09/25'. For use with water up to 23°C. This material is for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aliaxis Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EcoFITTOM Fittings'. Blue coloured PVC fittings which are manufactured by extrusion and molecular orientation. For use with water up to 60°C.
'TOM PVC-O Pipe'. Blue coloured PVC pipe which is manufactured by extrusion and molecular orientation. For use with water up to 60°C.
Range of WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M1005 X XXX | VARIOUS | 3/4” BSP male inlet. | 10 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn brass headworks, single lever operating members and self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The spout outlet incorporates a plastic flow straightener. The products are supplied with a shower hose, shower handset and brass back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Shower kit comprising of a shower hose, handset and a flow regulator. Open outlet use only. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43084 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43064 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T43194 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T44014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44054 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44034 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45004 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45014 | BSP 1/2" (F) | 10 bar | 85 °C | Company logo | On operating member | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TC28 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28, Production date (DD/MM/YYYY) | Body | No | |||||
| TC28-1 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28-1, Production date (DD/MM/YYYY) | Body | No |
Non-verifiable double check valve assembly with DZR brass body, incorporating two spring loaded, resilient trim in-line check valve cartridges. Compression connection to be used with copper pipe BS EN1057 only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C for 12.10102.035.CP5R-8511, Maximum operating temperature 65°C for 12.10112.035.CP5R-8511.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| XDSV12 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL15TA90 (Plastic)Red | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No | |||||
| SL15TA90 (Plastic)Blue | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No |
Range of quarter turn ceramic disc headworks with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks with brass bodies and EPDM ‘O’ rings. For insertion into specifically dimensioned tap assemblies Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HW28C | 27.8mm | bar | 85 °C | WANHAI, WRAS, HW28C, Production date (DD/MM/YY) | Body | No |
Kisdon range of single hole single outlet (swivel) pull out spray combination tap assembly (chromium plated brass) with ¼ turn ceramic disc headwork and single lever operating members. The outlet of the pull-out spray incorporates a plastic flow aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 818JK | Chrome | 1/2" BSP | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Waterfall | Click Type |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW103006000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | |
| TVW104002000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel) The products were already tested according to the TCS. The report from SKZ is attached.
Deck Mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator & flow straightener. Capable of achieving AUK3 tap gap. The product is supplied with a click type waste(not verified by test). Maximum working pressure 5 bar. Maximum operating temperature 65°C.
Single hole, single outlet, fixed combination tap assemblies (brass body chrome finish), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and an optional flow regulator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic disc headwork with various type operating members. The spout outlet incorporates a plastic aerator. Product is supplied with click type pop-up waste – not verified by test. Maximum working pressure 6 Bar. Maximum operating temperature 65°C.
A single-hole single outlet swivel combination tap assembly with brass body (chromium plated). Incorporating ceramic cartridge headwork. The spout outlet incorporate a plastic aerator. Maximum working pressure - 10 bar. Maximum operating temperature - 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, swivel, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Model BLS4ZZX is supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C.
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic flow straighteners. The products are supplied with a 15x15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) which also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of deck mounted, two hole, double outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks (DLV305B, DLT305B) or non-rising spindle headworks (CR305 BRIDGE, CR305/501 BRIDGE) and single lever or cross top operating members. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, double outlet (swivel) combination tap assembly incorporating quarter turn ceramic disc headworks with single lever type operating members. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc headwork with dome type operating member. Temperature is controlled independently via thermostatic cartridge with single lever operating member. The inlets incorporate a stainless steel strainers and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate It provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F3068-** | Various | BSP 3/4" (M) | 10 bar | 60 °C | LANBIAO | Rear of body | No | Ceramic disk diverter | Metal Backnuts | Aerator | Flow Regulator Fitted, |
1)No Suffix-Chrome 2)-**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 48 130 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 140 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 150 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 160 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 430 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 431 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish Products need to be installed in combination with basic set 10303180.
Range of three-hole, single outlet, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up or lever type waste – not verified by test. Maximum working pressure. 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B005* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of three-hole, single outlet (fixed) wall mounted combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with lever or cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of combined bath waste and overflow assemblies in various finishes.(see models for finishes) Maximum operating temperature: 60ºC
Range of free-standing sanitary macerating disposal units. The units are fed via a flexible hose assembly. Flow is controlled by a solenoid valve and discharges via a type `AB` air gap (verified by test, suitable of fluid category 5 backflow protection). Maximum working pressure 6.0 Bar Maximum operating temperature 40.0°C
Range of monochloramine generators incorporating UPVC pipework, fittings and an external flow sensor. Maximum working pressure 6.0 bar. Cold water use only.
Range of filling loop assemblies consisting of an in-line isolation valve, an in-line double check valve assembly (suitable for back flow protection against fluid category 3) that incorporates an isolation valve and a stainless-steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of green Sappro butt-welded polypropylene fittings for use with Sappro PPR pipes. Maximum working pressure: 20 Bar. Maximum operating temperature: 23°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
F1C compression & F5 press fittings for use with B1 multilayer PEX/AL/PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of DZR brass compression fittings for use with Q-Therm PEX-b Pipes (SDR 7.4) Maximum working pressure:20 bar, cold water use only
EG Range of copper, brass capillary lead free solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression fittings with brass, chrome plated brass bodies. For use with copper pipe (EN 1057) Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of compression fittings with brass, nickel plated brass bodies for use with copper pipe (manufactured to EN 1057). For above ground use only. Max working pressure 16.0 bar. Max operating temperature 85°C.
‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘CFxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
Range of compression fittings with polypropylene bodies for use with PE100 pipe (manufactured to EN 12201). Some of the female adaptors (55920-9-L, 55920-10-L, 55920-11-L & 55920-11-M), female threaded elbows (56935-10-L, 56935-11-L & 56935-11-M) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 16.0 bar. For above and below ground, cold water use.
Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
‘F17’ range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
5000 series of copper end feed fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Dual flush, WC outlet valves for either full or reduced flush. Incorporates an internal overflow. Cold water use only.
Stainless steel plate heat exchangers with copper brazing.
Range of pre-assembled hydraulic blocks incorporating plate heat exchangers, pressure relief valves set at 3.0 bar, circulation pumps and flow regulators. Maximum working pressure: Primary 2.5bar & secondary 10 bar. Maximum operating temperature 80°C (CH) & 60°C (DHW).
Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
An in-line ultra-sonic water meter with brass (WM15) or plastic (SM15) bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 50°C (WM15) or 70°C (SM15).
Range of water meters with plastic bodies and plastic turbines. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of booster pumps with stainless steel bodies, plastic impellers, and NBR ‘O’-rings. The products incorporate a temperature sensor, pressure sensor, pressure vessel and a non-return valve integral to the pump chamber. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C.
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.
Wall mounted finish set incorporating a dome type operating member and a shower hose and handset (chromium plated brass). Outlet to shower incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of overhead shower heads and arms incorporating a brass or ABS plastic body. The inlet of models KSAB4K and HEAH06BK incorporates a stainless-steel strainer and plastic flow regulator. Model EKIT01/A is a shower kit consisting of a shower hose, handset and riser rail and model AIR1HSCPWHUK shower handset only. Open outlet use only. Maximum operating temperature 60°C.
Range of shower handsets and headsets with chromium plated plastic bodies incorporating check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum working pressure: Open outlet. Maximum operating temperature: 60.0°C.
Range of wall mounted angled overhead showers, consisting of stainless-steel bodies (various finishes) and silicone nozzles. The inlets are fitted with plastic flow limiters. Maximum operating temperature 65⁰C. Open outlet use only.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| R 1/2 C | Chrome | 1/2" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| R 3/4 C | Chrome | 3/4" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps will be supplied with an optional Flow Regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C
Range of EVOX stainless steel or grey nylon braided polyethylene lined flexible hose assemblies incorporating EPDM ‘O’-rings with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 15 745 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 15 764 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 36 717 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 727 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 773 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of wall mounted, or concealed manually operated blending valves, (brass body, chrome finish), incorporating a ceramic cartridge headwork controlling both the flow and temperature with a single lever operating member. Maximum working pressure 5 bar. Maximum operating temperature 85°C.
Wall mounted thermostatic bar, shower valve, incorporating a ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Each inlet incorporates a combined EPDM washer and stainless-steel strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VE SHXSMFF C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| RP3 CE SHXSMFF C | Chrome (Cr3) | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43034 | Chromed | BSP 3/4" (M) x BSP 1/2" (M) offset unions | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43064B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43194B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Range of wall mounted, thermostatic shower valves (brass body – Chrome finish), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of wall mounted bar type thermostatic shower valves (brass body, chrome finish) incorporating quarter turn ceramic disc headwork which controls the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic blending valves with chrome plated brass bodies and ceramic disc headwork with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge also with a dome type operating member. Inlets incorporate single check valve cartridges however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of butterfly valves incorporating blue or green epoxy coated ductile iron bodies, discs and EPDM seals. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of flow control valves incorporating quarter turn ceramic disc headworks housed within a brass body. Maximum working pressure 6 bar. Maximum operating temperature 60°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line adjustable pressure reducing valves, with nickel plated DZR brass bodies and stainless-steel strainer. Various models are supplied with a pressure gauge (see model). Compression models are for use with BS EN1057 copper pipe. Maximum working pressure 16.0 Bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Wall mounted shower valve (chrome plated brass body) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of lockable, key operated, in-line spherical valves with brass bodies and nickel-plated brass ball. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of electronically actuated ball valves with brass bodies, chromium plated copper balls, PTFE and silica gel seals. Maximum working pressure 16.0 Bar. Maximum operating temperature 100°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 Bar. Cold water use only
Range of gate valves with blue, black or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
2Z126 FGAXXXB16NS01 range of brass gate valves or FGAXXXD16NS42 range of DZR brass body gate valves, with PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of non-rising spindle gate valves with bronze bodies, incorporating a hand wheel operating member. Maximum working pressure 16.0 Bar Maximum working temperature: 85C
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
AMEXSA range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, having rate of flow control facility controlled via a pilot system. Spring ratings of pilot valve are 2 to 20 psi / 0.138 to 1.38 bar, 25 to 50 psi / 1.72 to 3.4 bar. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
'Polyplumb' (grey coloured) & 'Polyfit' (white coloured) fittings. Injection moulded acetal fittings. For use with water up to 65°C.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Silicone Grease WA'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Proofex HDPE B125'. White coloured, extruded HDPE waterproofing membrane. For use with water up to 60°C.
'Netbor HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 65°C.
'Brothers Polyproplene fittings'. Blue coloured, injection moulded PP fittings. For use with water up to 65°C.
'SABIC® PP 56M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'15 EPR, 22 EPR & 28 EPR 'O' rings'. Black coloured, injection moulded 'O' rings. Shore hardness 60. Tested in-radius size 1.8mm. For use with water up to 85°C.
'EXJ2024'. Black coloured, compression moulded EPDM material. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'HT5697-50'. Black coloured, injection moulded EPDM material. Shore hardness 67 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'KF011670FDA'. Black coloured, compression moulded, FKM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MGA024BTM | Black | 1/2" BSP (F) | 9 bar | 65 °C | Mediclinics | Body | No | Solenoid | Not Applicable | Aerator |
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infrared sensor, and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure:8.0 Bar Maximum operating temperature:65 °C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a Syphon (Phantom S), Pneumatic Drop Valve (Phantom V) or Cable Operated Drop Valve (Phantom T) with full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or push button. Maximum working pressure 10.0 bar. Cold water use only.
W/C suite with pan (polyester) and a concealed flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a single flush drop valve for full flush volumes of up to 6 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 Bar. Cold water use only.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel or brass bodies, see models). The flow is controlled by a solenoid valve that is activated via an infrared sensor. Temperature is controlled independently via a single lever operating member. The spout outlets incorporate plastic aerators. Supplied with hoses that incorporate stainless steel strainers and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies). Flow is controlled by solenoid valves activated via an infra-red sensor and the temperature is controlled independently via single lever. The spout outlets incorporate plastic aerators. Maximum working pressure 8 Bar. Maximum operating temperature 65°C.
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator. The products are supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-PS***-**-**** | F1/2, M15*1 | Open outlet use only bar | 85 °C | Kind, WRAS, Production date(MM.YYYY) | Ferrule | No |
Note: 1. 1st *** denotes the hose length: 15-300cm: E.g., 015 = 15cm, 100 = 100cm, 200 = 200cm. 2. 2nd ** denotes the hose size: 06=DN6, 07=DN7 3. 3rd **** denotes the connections, and can be replaced with any of the following: 01=F1/2 05=M15*1
‘Union Range’ of shower kits. Comprising of a plastic shower handset, shower hose and brass wall outlet (various finishes – See model). The shower handset incorporates an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides backflow protection) Maximum operating temperature 60°C.
Range of T type thermostatic mixing valves with chrome plated DZR brass bodies. Compression and push-fit models for use with copper pipe manufactured to EN1057. Models 37.20122.015.CP,37.20122.022.CP, 37.21122.015.CP, 37.21122.022.CP, 37.21222.015.CP, 37.21222.022.CP, 37.20162.015.CP, 37.20162.022.CP have isolation valves and strainers on the inlet. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator and a swivel nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination taps assemblies (brass bodies - various finishes, see model) incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-down spray outlet with plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The cold inlet includes a loose chrome plated brass adaptor ½” BSP (M) x ½” BSP (F) incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The pull-out spray handset also incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar . Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8202W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8022W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-T8182W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8022AW | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8882CW | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Open Outlet |
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies -various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator, (except for the 3259-XX models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| R BAS C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | C-plate | Flow Straightener | Pop Up |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MA3580-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3580PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator |
Models added December 2025: MA3580PC MA3581PC MA3582PC MA3584PC
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 305B1 | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Aerator | |
| 824B | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Open Outlet |
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), Incorporating a ceramic cartridge headwork with lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The outlet incorporates a plastic aerator. One inlet hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating non-rising spindle headworks with dome type or cross top operating members. Both models are supplied with a plastic flow straightener. Capable of achieving AUK3 Tap Gap Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The outlet incorporates a plastic aerator. One inlet hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8204 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8184 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SH-T8035 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8066B | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Two hole, single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The 2259-XX model incorporates an open outlet spout, all other models incorporate a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assembly (brass body, various finishes), incorporating ceramic cartridge headwork and single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119A-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119A-L25-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 504109 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 5594201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 144201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8060A | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
Two-hole single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with cross-top operating members and a manual diverter to shower outlet. The product is supplied with a shower hose, shower handset and plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator, (except for the 1259-XX models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119-L25-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| USH0228 | chrome | 3/4" x 1/2" offset unions | 10 bar | 60 °C | SONAS | on body | No | 1/4 Turn ceramic disk |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L446100MA | Tri-chrome | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100DH | Matt black | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100SA1 | Brushed gold | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT010R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-KT008R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Various finish： (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC BDSM C MT | Chrome | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| RP3 VAC BDSM C MT | Chrome 3 | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B004* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| B009* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Rosette | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
*denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HGLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS38 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, |
Range of three-hole, metal, single outlet (fixed) deck mounted, combination tap assemblies, (brass bodies - various finishes, see model), incorporating quarter turn ceramic disc headworks with lever or cross top operating members. The products are supplied with stainless steel braided PEX lined inter-connecting hoses. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Free standing, upright floor mounted inlet legs (chromium plated brass), incorporating stainless-steel braided PEX lined flexible hose assemblies. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
‘LSMRI’ range of copper-nickel press fittings (‘M’ type crimp profile) for use with copper-nickel ‘LSMRI’ pipe. Above ground use only. Maximum working pressures: Press fittings: 16.0 bar, LSMRI-PN6 Series flange: 6.0 bar, LSMRI-PN10/16 Series flange: 10/16 bar. Maximum operating temperature 99°C.
Multipipe range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘HLBRxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The HLBRTC‐1 tank connector, HLBRSS‐1 and HLBRBS‐1 tap connectors all incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘3600xx’ range of brass compression fittings for use with copper pipe (manufactured to EN 1057). The 360014 tank connector, 360013 and 360017 tap connectors all incorporate an EPDM washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
'PlumbRight' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure 12.5 bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
“D-“ and “E-“ range of 304 and 316L stainless steel press fittings, in either ‘M’ press profile (D- prefix models) or ‘V’ press profile (E- prefix models) for use with stainless steel pipe (316L & 304 manufactured to EN10312). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature: 85°C.
Range of EPDM expansion joints with flanged end conenctors. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic flow meters with carbon steel bodies, NBR inner liner and stainless-steel electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Maximum operating temperature 60°C. Open outlet use only.
Range of wall or ceiling mounted shower arms with stainless steel bodies (various finishes - see model). Maximum operating temperature 60°C.
Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.
Range of PVC lined flexible shower hoses with a black or silver finish. Open outlet use only. Maximum operating temperature 60°C.
Range of flanged `Y` patterned in-line strainers with blue, black or red epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 936L | Chrome | G3/4, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 932L | Chrome | G1/2, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 530 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | 1/4 Turn ceramic disk | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature: 60°C.
Range of EPDM braided hoses (various options) and optional end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of flexible corrugated stainless-steel tubing with white plastic covering. Compression connections are for use with copper pipe (manufactured to EN 1057). Captive nut end connections incorporate an EPDM gasket. 2BACa0504 prefix models incorporate a servicing valve (chromium plated brass body with brass ball) on the compression end connection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of air venting valves with a blue epoxy coated ductile iron body, plastic float, EPDM ‘O’-rings and seals. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 16 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of wall mounted, thermostatic blending valves incorporating ceramic disc diverter cartridges. Inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to verify backflow protection. Product also had manual override button, with variations of dome and single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814109 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, | ||
| 814111 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, |
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. The valves incorporate a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of double swing gate, wafer, non-return valves with blue, black or red epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A range of non-return valve with blue epoxy coated ductile iron bodies, stainless-steel disc and EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs, PTFE stem gaskets and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated). The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, spherical valve and DZR pilot valve, DZR electrically actuated spherical valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 2.0 bar – 12.5 bar. Maximum operating temperature 80°C.
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of spherical valves with nickel plated brass bodies, brass ball and PTFE seats. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of blue or green polyethylene coated ductile iron gate valves incorporating an EPDM Wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 10.0 Bar or 16.0 Bar Maximum operating temperature 40.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
'BSS-P'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'BSS-P-D0002' dated '2025-1-10'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BSS R/G System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘BSS Red and BSS Grey’. ‘BSS Red’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘BSS Grey’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet ‘BSS-D0003’, dated ‘2025-09-16’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9001 Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's TDS/IFU 'number: 001', 'First Edition', revision date 'March 20, 2025'. Cure for 60 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-LM'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no. BSS-LM-D0001', 'Date: 9.20.2025'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.1 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver 1 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitcote CM 210’. Site applied, two-part, grey coloured (once applied), Cementitious Waterproofing coating. Mix ‘CM 210 white’ liquid polymer and ‘CM 210 grey’ powder in a 1:3.6 weight ratio and apply two coats as per manufacturer's TDS 'UAE/0210/23/Z-1'. Cure Coat 1 for 3 hours@35°C and Coat 2 for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-U Yellow & Blue'. Fibre/NBR materials, available in yellow or blue colours, manufactured by calendaring. Tesnit BA-U Blue is for use with water up to 85°C. Between September 2025 and February 2026, Tesnit BA-U Yellow was for use with water up to 23°C. Between March 2026 and September 2030, Tesnit BA-U Yellow is for use with water up to 85°C. Store and handle in accordance with 'STORING & HANDLING INSTRUCTIONS, dated November 12, 2025'. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Grivory GVN-5H black 9915'. Black coloured, injection moulded PA 66 + PA 6I/X-GF50 material. For use with water up to 85°C.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
Grilamid LV-30H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA natural. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural & Grilamid LV-65H FWA black 9225 were added to the approval in March 2026. Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. For use with water up to 85°C.
'IP 90606'. Orange coloured, injection moulded Polyester resin material. For use with water up to 50°C.
'Tritan™HM1060'. Clear (translucent), injection moulded copolyester material. For use with water up to 85°C.
'Innogaz'. Black coloured, injection moulded, HDPE (PE100) electrofusion fittings. For use with water up to 60°C.
'NOVATHERM Pipe'. Green coloured (with external red stripes), extruded PPR pipe. For use with water up to 60°C.
'NOVATHERM Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 60°C.
'Vesbo Pipe'. Green coloured (with external red stripes), extruded PPR pipe. For use with water up to 60°C.
'Vesbo Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 60°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'DLYY E6202'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.1mm. For use with water up to 23°C.
'Dutral K-Co-054'. Black coloured, compression moulded EPDM materials. Shore hardness between 52A & 80A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'SM177'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.56mm. For use with water up to 23°C.
Range of injection moulded, VMQ rubber gaskets, seals, & `O` rings manufactured from the below compounds. The components are available in blue, green, grey, opaque (beige coloured), red, transparent & yellow. The numbers in the name of the compound indicates the shore hardness between 40 & 80. Tested in-radii sizes: Gaskets: 0.2mm - 5.0mm. Seals & `O` rings: 0.5mm - 5.0mm. S50B04E, S60B00E, S70B06E, S70B07E, S70V02E, S50V01E, S60O02E, S70O05E, S50O03E, S50O05E, S60O01E, S70O03E, S40A01E, S60A00E, S70A02E, S40R03E, S45R01E, S50R10E, S50R01E, S60R05E, S65R04E, S70R04E, S80R01E, S40R02E, S50R06E, S60R07E, S70R19E, S70R24E, S50T05E, S50T00E, S55T00E, S60T00E, S60T00T, S70T04E, S70T00E, S75T00E, S80T00E, & S70G01E. For use with water up to 85°C.
72401, 72501, 73401, 73501, 74401, 74501, 75401, 75501, 76401, 76501, 77401, 77501, 78401, 78501, 79401 & 79501. Range of press moulded, solid silicone rubber materials which are blue or red coloured. Shore hardness between 20 & 90. Tested in-radius size 1.0mm. for use with water up to 85°C.
'Hytrel® 4068FGDW'. Cream coloured, injection moulded, thermoplastic polyester elastomeric material. For use with water up to 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 4203801-1 | chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, |
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT103002000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT104001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT125001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT105501110XX | See Below | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | Lever | No | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Wall mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headworks with cube operating member and incorporating a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of spherical valves with DZR brass bodies, chromium plated brass balls, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Compression connection to be used with copper EN1057. AI-0396A062815CR incorporates an approved single check valve cartridge, verified by test - suitable for backflow protection against fluid category 2. Maximum working pressure: 25.0 bar. Maximum operating temperature: 100°C (model AI-0396A062815CR 65°).
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of shower hoses. The H-38033 model has a PVC inner liner and stainless steel interlocked outer casing. The H-38034 and H-38035 models are multi-layer shower hoses with a PVC inner liner. Maximum operating temperature 60°C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814110 | chrome | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, | ||
| 814112 | 814112 | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, |
Range of T-type thermostatic mixing valves with chromium plated brass bodies. The inlets incorporate a stainless-steel strainer and an approved single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets of model MT753CP-ISO also incorporate an isolation valve, Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Spring loaded, resilient trim check valve cartridge with plastic body and EPDM O-rings. For insertion into fittings with specifically sized bores. Maximum working pressure: 16 Bar. Maximum operating temperature: 85°C.
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum operating pressure 10.0 bar. Maximum operating temperatures: 430357-003, 430357-004 and 430357-006 models: 85°C, 430357-008, 430357-010, 430357-011 and 430357-012 models: 65°C.
In-line non-verifiable double check valve assembly with integral lever operated spherical valve, consisting of two spring loaded resilient trim check valve cartridges housed within a DZR brass body, verified by test (suitable for backflow protection against Fluid Category 3). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks and cross top operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste (not verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D22 | 22 mm | 10 bar | 85 °C | Gear, D22, Production date (DD/MM/YY) | Body | No | |||||
| D15H | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| D15C | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| R19H | 19 mm | 10 bar | 85 °C | Gear, 19H, Production date (DDMMYY) | Body | No | |||||
| R19C | 19 mm | 10 bar | 85 °C | Gear, 19C, Production date (DDMMYY) | Body | No |
Range of ceramic cartridge headworks with EPDM seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar, Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The cold inlet and shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever or dome type operating members. The spout outlets are either open outlet or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and the spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L449200DH | Matt black | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200MA | Tri-chrome | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200SA1 | Brushed gold | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating ceramic cartridge headworks with single lever operating members Spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 141701 | chrome | 1/2" BSP | 10 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Aerator |
Range of wall mounted, two-hole, single outlet, fixed, combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Products incorporate a hand shower and a manual diverter to shower outlet. Models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 6.0 Bar. Maximum operating temperature: 65°C.
Range of deck mounted, two-hole, single outlet, fixed, combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator, and manual diverter to shower outlet. Products supplied with shower hose and handset. Models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 6.0 Bar Maximum operating temperature: 65°C
Range of Floor mounted, two-hole, single outlet combination tap assemblies (chromium plated brass), incorporating ceramic disk headwork with single lever operating members. The spout outlets incorporate a plastic aerator and a manual diverter to shower outlet. Products are supplied with a shower hose and handset. Models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 6 Bar Maximum operating temperature: 65°C
Two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass & matt black finish) incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Spout incorporates a flow straightener. Product supplied with metal backnuts Maximum temperature 65 °C Maximum pressure 10.0 bar
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 503109 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 5593201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 143201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K005* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| K008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 20.189.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| 20.193.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
Where xxx denotes finish, can be replaced by: 002 – Chrome DC2 – Supersteel DA2 – Warm sunset AL2 – Brushed hard graphite A02 – hard graphit DL2 – brushed warm sunset GN2 – brushed cool sunrise A02 – hard graphite MS2 – satin steel GL2 – cool sunrise MS2 – satin graphite
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with stainless steel braided EPDM lined interconnecting hoses. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of chemical dosing equipment which incorporate self-closing valves and plastic bodies. The outlet of the injector incorporates a connection for injection of chemicals via venturi action and the inlets include stainless-steel strainers. Maximum operating pressure 9 bar. Maximum operating temperature 70°C.
Range of Socket weld, Click weld, Butt weld and Electro fusion fittings (see models), for use with ABN//INSTAL CT Faser RD Series 3.2 / SDR 7.4 & ABN//INSTAL CT Faser RD Series 5 / SDR 11 pipe. Maximum working pressure; (see models) Maximum operating temperature; (see models)
Range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *‐KJ600304 and *-KJ600316 stainless steel pipes. The "KJ6278" prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass compression fittings for use with copper pipes (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flange fittings with TP2 copper bodies, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘M’ profile copper press fittings with EPDM ‘O’-rings for use with copper pipes (manufactured to EN 1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
'Flomasta’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Range of end feed copper fittings for use with copper pipes (manufactured to EN 1057). The 5043G series and 5002G series models incorporate an EPDM ‘O’-ring on the captive nut connection. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of ultrasonic dry type water meters with brass bodies. Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C.
‘BECO Y’ range of ultrasonic water meters with plastic bodies, plastic transducers and silicone ‘O’-rings. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass bodied threaded fittings and a brass end feed fitting (C04069H00081A model only). The CL08069H192B4 model is chrome plated. The C04069H00081A model end feed fitting is for use with copper pipe (manufactured to EN 1057). The C04149H00191A model incorporates a plastic flow straightener. Maximum working pressure 10.0 bar, except for the C04149H00190A and C04149H00191A models which are open outlet use only. Maximum operating temperature 85°C.
Threaded adaptor (brass body) soldered with copper pipe and a range of thread extensions (chrome plated brass bodies). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FH SLRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 BB | Brushed Brass | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 GM | Gun Metal | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| 225788 | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| RP3 FH SLRD01 C | chrome 3 | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 G | Gold | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, |
Two Fixed Head's with different finish and size as below FH SLRD01 C / BB / GM - (Dia 200mm) FH SLRD02 C - (Dia 250mm) FH SLRD03 C - (Dia 300mm) 225788 - (Wickes selling code for FH SLRD03 C) RP3 FH SLRD01 C - (Dia 200mm, chrome 3) FH TDRD01 C - (Dia 157mm) FH TDRD01 C / G - (Dia 200mm) FH TDRD03 C - (Dia 300mm)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WH51-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH03** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-WH05** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA61** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA60** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA55** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA54** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No |
The suffixes of ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.477.xxx | Various | G 1/2" | Open Outlet bar | 65 °C | Grohe | Shower faceplate | No | Fixed Head, |
Where xxx denotes finish, can be replaced by: 000 – Chrome DC0 – Supersteel DA0 – Warm sunset LS0 – moon white AL0 – Brushed hard graphite DL0 – brushed warm sunset GN0 – brushed cool sunrise GL0 – cool sunrise MG0 – satin graphite MS0 – satin steel A00 – hard graphite BE0 – polished nickel EN0 – brushed nickel
Range of shower handsets with ABS bodies (various finishes, see model). The spray outlet is either multifunction or single function depending on series. Open outlet use only. Maximum operating temperature 60°C.
Range of wall mounted or ceiling mounted shower arms with brass bodies (various finishes - see model). Maximum operating temperature 65°C.
Range of In-line Y patterned strainers with ductle iron bodies (blue epoxy powder coated) and stainless-steel mesh. Maximum working pressure: 16 Bar Maximum operating temperature: 85 °C
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FBA015 | Bronze | 1/2" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable | |
| FBA020 | Bronze | 3/4" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable |
Range of drain taps with a brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SD2001 | 1/2" BSP (M) | 16 bar | 85 °C | SD and size | Body | No | |||||
| SD2001 | 3/4" BSP (M) | 16 bar | 85 °C | SD and size | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| RS2 3/4 C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| 225916 | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 HNK FL5 C CD | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| TAP1103 | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M3401 X XXX | VARIOUS | 1/2” BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/2 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Flow Regulator Fitted, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Deck mounted pillar tap (chrome plated brass body) incorporating quarter turn ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of shower hoses, multi-layered hose (various external finishes) with PVC inner liner, brass end connections. Open outlet use only. Maximum operating temperature 60°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of Stainless-Steel braided EPDM lined flexible hose assemblies with various end connections. For use with copper pipe manufactured to EN1057 Maximum working pressure; 16 Bar Maximum operating temperature; 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate push-fit isolation valves. Compression connection to be used with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. Maximum working pressure and maximum operating temperature 12 bar @cold water use only & 7 bar @ 65°C.
Range of domestic stainless steel or coated carbon steel indirect unvented hot water storage cylinders and buffer tanks, incorporating a stainless-steel coil for connection to a heat pump circuit. The secondary circuit is factory fitted with a temperature and pressure relief valve (7.0 Bar @90°C) and an immersion heater. Maximum working pressures: Water storage tanks (ECO-ZR200S and EG-200CAIO): 5.5 bar. Buffer tank (ECO-ZR60 and ECO-ZR60S): 7.0 bar. Maximum operating temperature 70°C. The ECO-ZR60 and ECO-ZR60S models are to be used in a primary circuit only.
Range of automatic air release valves with blue epoxy coated cast iron bodies and plastic floats. Maximum working pressure 10.0 Bar 16.0 Bar, 25.0 Bar (see models) Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQDL1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 938HP | Chrome | 15mm Compression | 5 bar | 70 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 958HP | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic shower valves, (brass bodies - various finishes), incorporating a thermostatic cartridge controlling the temperature. Supplied with either single lever or cross top operating members depending on model and with a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork, controlling and diverting the flow between overhead shower and handset, with dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate stainless steel strainer and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection Maximum working pressure 10.0 bar. Non-metallic materials and components comply with BS6920 at 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic mixing valves with between 1 and 2 outlets. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Models Mira Activate 1.1903.090, 1.1903.091, 1.1903.092 & 1.1903.093 incoporate a built-in pump. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves have a maximum working pressure of 1.0 bar. Maximum operating temperature 45°C.
Range of wall mounted thermostatic shower valves with brass bodies and trim set (various finishes - see model). Flow is controlled by a quarter turn ceramic disc headwork with various operating members. Temperature is controlled independently via a thermostatic cartridge with various operating members. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQ75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, | |
| TS75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, |
AQ75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 704418 (shower handset) • ACY1008 (shower hose) TS75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 707540 (shower handset) • ACY1008 (shower hose)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV1 | Chrome | 5 bar | 65 °C | Aqualisa | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, |
AQRNDCV1 Packed Products. Waterway contents are: 705342 (shower valve) 704418 (shower handset) ACY1008 (shower hose) ACY1013 (wall outlet)
Range of thermostatic shower valves with a quarter turn ceramic disc headwork or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar Maximum operating temperature 65°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, with stainless steel (CF8 or CF8M) discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of double flanged butterfly valves with blue, lavender or bright blue epoxy coated ductile iron bodies, EPDM seats and either white or red epoxy coated ductile iron or stainless steel discs. The products are supplied with bare shaft without operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of lugged butterfly valves incorporating black epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. From March 2023 the valves are also available with blue epoxy coated ductile iron bodies. The products are operated by: Gearbox or DRV gearbox operating members, or bare shaft without operating members. Maximum working pressures: RBV020-H models: 16.0 bar, RBV-S/PN25 models: 25.0 bar Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | GEAR, Model no. and Prodcution date (DD/MM/YY) | Body | No | |||||
| D35 | 35mm | 10 bar | 85 °C | GEAR, Model no | Body | No |
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, incorporating a solenoid valve. Maximum working pressure 12.0 Bar Maximum operating temperature 60.0°C
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘GNVP’ range of non-return valves with a white plastic housing. The product incorporates two test/drainage plugs. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of in-line pressure reducing valves with either chromium plated DZR brass bodies, with manually adjustable outlet pressure ranges between 2.8bar to 3.2bar. Compression connections to be used with copper pipe EN1057 only. Maximum working inlet pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of pressure reducing valves, manually adjustable outlet pressure from 0.5 bar - 6.5 bar, with DZR brass bodies and inspection ports on both the inlets and outlets. The valves incorporate plastic strainers. Maximum working pressure 25 bar. Maximum operating temperature 85˚C.
Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of pilot operated pressure reducing control valves (ranges of 0.7 to 7.0 bar or 1.5 to 15.0 bar) with ductile iron bodies (blue epoxy coating). Maximum working pressure: 16 Bar. Cold water use only.
Range of pilot operated pressure reducing control valves with ductile iron bodies (blue polyester or epoxy coating) or stainless-steel bodies. Maximum working pressure 16 Bar (PR models) 12 Bar (PR-SC models) Maximum operating temperature 60°C Pressure ranges 0.35 bar-3.5 bar, 0.7 bar-5.5 bar, 1.38 bar-13.8, 6.9 bar-16 bar.
Pressure relief valve with a brass body. Pre-set at 2.5 bar relief pressure. Maximum operating temperature 110°C.
Range of spherical valves nickel plated brass body with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
In-line spherical valve incorporating a chrome plated brass body and ball. Compression end to be used with copper pipe EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Spherical ball valve (screwdriver operated) incorporating a chromium plated brass body and ball. For use with BS EN 1057 copper pipe Maximum working pressure 16 Bar Maximum operating temperature 85°C
Range of spherical valves with various means of operation some via handle some with actuators, see models, comprising of a bronze valve body, spindle and ball valve, and EPDM O rings Maximum working pressure 16 bar Maximum operating temperature 90˚C.
Spherical valves incorporating a brass bodies and ball, PTFE seat, EPDM and NBR ‘O’-rings. The valve 8 718 657 822 incorporates a branch which is intended to connect to the primary circuit of a combination boiler. Maximum working pressure 10.0 Bar. Cold water use only.
Range of angled (S0273 and S0274 suffix models only) or in-line spherical valves with a nickel plated brass body, chromium plated brass ball and PTFE or EPDM seats. The products are either screwdriver operated or supplied with a T-handle (S0233BH-1 and S0233BH-2 models only). Compression ends are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass balls (chrome plated) and EPDM ‘O’-rings. For use with copper pipe to (EN1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Push fit in-line spherical valve with plastic body, for use with PE-X pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe (manufactured to BS EN1057). Maximum working pressure/temperature: 12.0 Bar (cold water) and 7.0 Bar at 65°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves with a non-rising spindle and a handwheel operating member. DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM wedge and a non-rising spindle. Maximum working pressure 16.0. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. The valves operate via a non-rising spindle headwork with hand wheel, bevel gear, electric actuator & stem cap operator operating methods. Maximum working pressure 10.0 or 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, for use with copper pipe (manufactured to EN1057). Incorporating a either a handwheel or lockshield operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of stop valves with brass bodies (see models) with T-type operating members. The 15mm, 22mm and 28mm compression sizes are for use with copper pipe (manufactured to EN 1057). The 20mm and 25mm compression sizes are for use PE pipes (manufactured to EN 12201-2). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Series 116’ range of balancing valves (DZR Brass body). Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AFIL BLUE Tank Panel'. Beige coloured GRP tank panel manufactured by continuous winding. For use with water up to 60°C.
'AFIL BLUE Pipe'. Beige coloured GRP pipe manufactured by continuous winding. For use with water up to 60°C.
'Versilon™ C-544-A I.B'. Triple layered, extruded tube consisting of a transparent (clear) polyurethane inner layer, white coloured polyester middle layer & transparent (clear) polyurethane outer layer. For use with water up to 65°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
'TIMO 5-70 Gaskets & ‘O’ rings'. Black coloured, injection moulded EPDM gaskets & ‘O’ rings. Shore hardness 70. Tested in-radius size between 0.50mm & 2.66mm. For use with water up to 85°C.
Range of combination tap assemblies with a single outlet and fixed spout incorporating a manual diverter to shower. With a ceramic disc headwork and the spout incorporates a flow straightener. Maximum temperature 65 °C Maximum pressure 5.0 bar
'UPMC uPVC Pipes'. Grey coloured, extruded uPVC pipes. For use with water up to 60°C.
Range of deck mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use only
Range of combined bath filler, waste and overflow assemblies. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH001* | Various | ½” BSP (F) conical nut x ½” BSP(F) conical nut | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable | |
| SH002* | Various | ½” BSP (F) conical nut x M15x1 | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable |
1) The products are interlock type 2) * denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of near boiling water dispensers comprising of an install rail, under-counter boiler unit with a stainless steel tank and a countertop outlet (font). The install rail incorporates a water block, a double check valve assembly (suitable for backflow protection against fluid category 3) with an integral lever operated isolation valve and an adjustable pressure reducing valve (outlet pressure range 3.0 to 3.5 bar). The flow is controlled via a solenoid valve which is activated by a touch method at the outlet. The commercial model outlets (fonts) incorporate a safety button. The solenoid valve incorporates a plastic flow regulator. The countertop outlet (font) incorporates a plastic aerator. All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Maximum supply pressure to the install rail 16.0 bar. Maximum operating temperature 98°C. Cold supply only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| D39 | 39mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
Quarter turn ceramic disc headwork incorporating a brass body, EPDM and NBR ‘O’-rings and a silicone gasket. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 122 100 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 122 101 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 579 600 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 333 001 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 700 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 702 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable |
30 122 100 - Diameter= 25,4mm 30 122 101 - Diameter= 25,4mm 30 333 001 - Diameter= 25,4mm 30 746 700 - Diameter= 25,4mm 30 746 702 - Diameter= 25,4mm 30 579 600 - Diameter= 25,4mm
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 501102 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 501101 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591103 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141102 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator |
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes), ceramic cartridge headwork with a single lever operating member and waterfall spout outlet. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies -various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator, (except for the MYKCOR002 & BLKCOR002 models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| KM FRZ BAS3.5 C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Operating member | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies, chrome finish(chromium plated brass), with a non-rising spindle and cross-top operating member(models 49944 & 88081) or ceramic disc headwork with lever type operating members(model 26251). The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 247031 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247032 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247033 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Lever or Dome type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 526402 | Chrome (CHR) | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526407 | ANT/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526415 | BLA/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526408 | SGW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526981 | VGR/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526980 | SOW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator |
All surface finishes are not in contact with drinking water. The product structure (schedule of materials) of all versions are identical. Surface finish / color explanation: CHR - Chrome ANT - Anthracite BLA - Black Matt SGW - Silgranite White VGR - Volcano Grey SOW - Soft White
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The MYKCOR003 model incorporates an open outlet spout, all other models incorporate a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| J THBSMVO C | Chrome | G 3/4" (M) | 10 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Flow Regulator Fitted, |
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator, (except for the MYKCOR004(& BLKCOR004??? models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 PSNK C CD | Crome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
Note - Both Products are the same, one is wall mounted, one is deck mounted.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-L201** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| JD-200** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| SJS-L202** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Floor mounted spout outlet, (brass body – various finishes) incorporating a plastic aerator. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-SP501 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Spout | No | Not applicable | Aerator | ||
| SJS-SP205 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Decorative plate | No | Not applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Uponor S-Press press fittings, Uni-X & Uni-C compression fittings for use with Uponor MLC pipe. Maximum working pressure 10.0 bar, maximum operating temperature 70°C.
‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Numepress' stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of copper press fittings with EPDM seals for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Fastwarm range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘Fastwarm’ range of U profile press fittings (nickel plated brass bodies) for use with ‘Fastwarm’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper capillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
Page 8 of 9
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
