‘Polytank 4 Layer Multilayer LLDPE Tank Panel'. Multi-layered LLDPE tank panel, manufactured by rotational moulding, consisting of a white coloured inner layer, light grey coloured second layer, black coloured third layer & white coloured outer layer. For use with water up to 65°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'Corirubber 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'ergo 4207 (yellow coloured), 4205 (white coloured) & 4453 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
Range of electronic, touch free, wall-mounted taps (chromium plated brass. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, with either bottom entry (A28-06 XXX models) or side entry (A28-06 side). The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar Cold Water Use Only
Range of bottom entry BS1212-4 (2016) delayed or non delayed (all models)action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of spring loaded single check valve cartridges comprising of a POM body and cap, stainless steel spring and EPDM gasket and O-rings. Max working pressure 10 bar. Max operating temperature 85°C.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating a brass body (various finishes) and ceramic cartridge headwork with single lever operating members. The outlets incorporate a plastic aerator. Model 63785-00XX incorporates a pull-out spray with push button trigger assembly. The pull-out spray incorporates a single check valve assembly (however the complete unit has not been tested to demonstrate it provides adequate backflow protection). Model 63787-00XX incorporates a pull-down outlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 143138 X XXX | VARIOUS | 1/2" | 10.0 bar | 65 °C | PPI | Rear of body | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 197021 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | Non-rising spindle | C-plate | Aerator & Flow Straightener | |
| 207121 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 207125 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Cross top Dome or Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| COB BF C | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 COB BF C | CROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| COB BF BLK | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 144347 | CHROME | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 257580 | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 COB BF BLK | BLACK | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Handle or Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener |
Model added February 2026: RP3 COB BF BLK
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193706 X XXX | VARIOUS | ¾” BSP (M) | 10.0 bar | 85 °C | PPI | Rear of tap body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : H (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Floor mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members and a manually operated diverter to shower outlet with a single lever operating member. The product is supplied with an approved shower hose and handset. Product is to be installed with a floor mounting kit. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193705 X XXX | VARIOUS | ¾” BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of two hole, double outlet (swivel) combination tap assemblies (chromium plated brass). The TAP2014 model incorporates non-rising spindle headworks with dome type operating members. The TAP 9023 model incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
Range of deck mounted three-hole, single outlet (fixed) combination tap assemblies (various plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60.0°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CLS201 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS211 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS214 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| CLS215 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS210 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS220 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS230 | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22D | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS22E | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24A | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24B | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
| BLS24C | Various | 1/2 | 6Bar bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Interconnecting Hoses, |
Finishes available: Chrome, Brass, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Vintage Brass, Gold, Matte Gold.
Range of bath filler waste kits incorporating a brass inlet elbow and overflow assembly, a copper hex nut, overflow housing. Maximum Working Pressure 5.0 bar. Maximum operating temperature 70.0 C
Range of stainless-steel expansion joints. Maximum working pressure 6.0 bar. Maximum operating temperature 90°C.
Range of stainless steel axial expansion joints (various end connections - see model). Maximum operating pressure 16.0 bar. Maximum operating temperature 100°C.
TY-11 & TY-03 ranges of expansion vessels. The TY-11 range has an epoxy coated carbon steel body and the TY-03 range has a stainless-steel body. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of filling loop assemblies, comprising of a stainless-steel braided EPDM lined hose, isolation valve (screwdriver or lever operated) with a DZR brass body and a double check valve incorporating a built-in isolation valve (screwdriver or lever operated) a DZR brass body. The F1400120012211 model has an approved double check valve incorporating a built-in isolation valve with a DZR brass body at each end of the filling loop. All valves are nickel plated. The products are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of Aquaterra PP-RCT socket fusion fittings for use with Aquaterra PP-RCT SDR 6 pipe and Aquaterra PP-RCT SDR 7.4 pipe and Aquaterra PP-RCT SDR 9 (manufactured to EN ISO 15874). 160mm Cold water use only @16bar Maximum working pressure 16.0 bar. Maximum working temperature 85°C.
Range of clamp fittings incorporating DZR brass bodies. For use with PE 100 RC pipe (manufactured to EN12201) only. Maximum operating pressure: 16 bar. Cold water use only.
Range of Instantor Irish Compression Fittings with brass bodies for use with copper pipe to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 99°C.
FLOWTECH range of fusion welded, PP-RCT fittings for use with Atlas PP-RCTGF pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of brass compression fittings for use with copper pipes and Irish copper pipe (both manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: 32612, 32634, 32712 & 32734 models: 65°C. All other models: 85°C.
Range of DZR brass push fit fittings for use with copper pipe (EN1057). Maximum working pressure 10.0 Bar. Maximum operating temperature 65 °C.
Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Zip Aquapoint IV’ range of wall mounted directly heated unvented storage vessels (cased and insulated) incorporating an enamel lined cylinder and safety kit. The cylinder is factory fitted with a temperature and pressure relief valve (7.0 bar/90°C) and a drain valve. The product is supplied with an installation kit comprising of an expansion vessel, tundish and an inlet manifold incorporating a 6.0 bar expansion relief valve, an adjustable pressure reducing valve with stainless-steel strainer (adjustable between 2.7 and 3.3 bar, but pre-set at 3.0 bar), and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The compression connections of the installation kit are for use with copper pipe (Manufactured to EN 1057). Maximum working pressure 5.5 bar. Maximum operating temperature 70°C. Cold supply only.
Range of ultrasonic water meters with brass bodies, plastic transducers and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of flow restriction blocks with a stainless-steel body and integral stainless-steel filter. Maximum working pressure 16.0 Bar Cold water use only.
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of ‘SureCal’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of single and twin ended shower booster pumps with plastic bodies and plastic impellers. The inlets/outlets incorporate stainless steel braided EPDM lined flexible hose assemblies with isolation valves and stainless-steel strainers. The outlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The Universal Twin models incorporate an expansion vessel. Maximum working pressure 1.5, 1.8, 2.0, 2.5, 2.6, 3.0 Bar (see model for more details). Maximum operating temperature: 60.0°C.
Range of multi-stage semiaxial submersible pumps with stainless steel bodies and impellers. Please note, this approval does not cover the motor, motor connection kit or power cable necessary for the pump to operate. Open outlet use only. Cold water use only.
STORMBOOST range of domestic water pressure booster pumps with brass impellors, brass bodies with accumulators, available from 60 – 300 litres (please refer to model). Models are supplied with reducing bushes, pressure gauges, pressure reducing valves and double check valve assemblies housed in DZR brass bodies with isolation valves and strainers. Maximum working pressure 4.5 bar. Maximum operating temperature 23°C.
Range of shower handsets with various plated plastic bodies. The product incorporates a stainless-steel sieve a flow regulator. Maximum working pressure: open outlet use only. Maximum operating temperature: 60.0°C
Range of chrome plated plastic shower handsets, incorporating a flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60.0°C.
Range of wall mounted brass shower outlets in various finishes. Open outlet use only. Maximum operating temperature: 65°C
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of `Y`-patterned strainers with either brass or DZR brass bodies, incorporating a stainless-steel mesh strainer. Maximum working pressure: 25.0 Bar (1SYA Models) or 16.0 Bar (1SYC & 1SYD models) Maximum operating temperature 95°C. Strainers with compression connections are to be used with copper pipe manufacture to BS EN 1057. Strainers with M profile press-fit connections are to be used with copper pipe manufactured to BS EN 1057 & SS304 Stainless steel pipe manufactured to EN 10312.
Range of chrome plated brass bodied bib taps, with cross top operating members, the outlet incorporates a hose union (B1674AA) or a plastic flow straightener (B1673AA & B1675AA). The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar, Maximum operating temperature 60°C.
Range of wall mounted bib tap with brass bodies (various finishes - see model), incorporating either non-rising spindle headworks with cross top operating members or quarter turn ceramic disc headworks with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HOU 1/2 C | Chrome | 1/2" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| HOU 3/4 C | Chrome | 3/4" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| RP3 HOU 1/2 C | Chrome | 1/2" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator | ||
| RP3 HOU 3/4 C | Chrome | 3/4" BSP | 5 bar | 60 °C | Bristan | Handle or Body | No | Metal Backnuts | Aerator |
Range of EPDM or PVC lined, interlocked stainless-steel shower hoses. Open outlet use only. Hoses with an EPDM liner have a maximum operating temperature of 85°C. Hoses with an PVC liner have a maximum operating temperature of 65°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass bodied automatic air venting valves incorporating a plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 110°C
Range of wall mounted thermostatic bar shower mixers (brass bodies – various finishes) incorporating a ceramic cartridge headwork that controls the flow and diverts form hand shower to overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge with dome or cubed type operating members that incorporate a manual override button. The inlets incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Supplied with a hose, handset and overhead shower outlet. Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
Range of concealed thermostatic blending valves (brass bodies – various finishes) with ceramic diverter controlling the flow which also diverts to 2 outlets and a thermostatic cartridge controlling the temperature independently. The inlets incorporate an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset not supplied. Maximum working pressure 10.0 Bar Maximum operating temperature 70 °C.
Range of wall mounted, concealed thermostatic shower valves with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks controlling the flow with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge, the inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and a stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, thermostatic, shower valves, (brass bodies - various finishes) incorporating a two-way ceramic disc diverter headwork to control the flow between two shower outlets with dome type operating members. The temperature and flow is controlled by a ceramic cartridge headwork with a single lever. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a hose, handset and overhead shower. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313963 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 309644 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| AR3 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313960 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| DEL SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286569 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285401 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286565 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286566 | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286567 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285400 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313962 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313965 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BB | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BLK | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311671 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311672 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311673 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 231844 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313961 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV GM | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCVO C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 SAI SHCDIV C | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Model added February 2026: RP3 SAI SHCDIV C
Range of manually operated flow control valves with brass bodies and either ¼ turn or ½ turn ceramic disc headworks (refer to model). The products are available with trim sets and operating members in various finishes (refer to models). Maximum working pressure 5.0 bar. Maximum operating temperature 85⁰C.
Range of spring loaded, resilient trim, non-return valves with a brass body bonnet and disc holder, stainless steel spring and strainer. Max working pressure 20 bar. Max operating temperature 85°C.
Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of non-return, swing gate valves with bronze, DZR brass or brass bodies and DZR brass, bronze or brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of pre-set pressure relief valves with gunmetal bodies and a lever operated easing gear. Pre-set relief pressures: 1.0 bar to 10.5 bar. Maximum operating temperature 95°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screwdriver operated spherical valves with brass or chrome plated brass bodies Compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 8.0 Bar Maximum operating temperature 80 °C.
Range of straight isolation spherical valves in Brass or Nickle-Plated Brass. Models have screwdriver or butterfly operating members. Maximum working pressure 10.0 or 16.0 bar. Maximum operating temperature 85°.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. B40 Bronze range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. B10 Brass range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of spherical valves with bronze bodies incorporating a brass or stainless-steel ball with PTFE seat. Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with nickel plated brass bodies Max working pressure: 20 bar. Max operating temperature: 85°C.
Range of spherical valves with nickel plated brass bodies, nickel plated brass ball and PTFE seats. The LD 47.300.XX and LD 47.302.XX models have a butterfly handle. The LD 47.301.XX and LD 47.303.XX models have a lever operating member (normal and special type). The LD 47.340.XX and LD 47.342.XX models have a T-handle. Maximum working pressures: ½” - 1” sizes: 40.0 bar, 1¼” - 2” sizes: 25.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with either DZR brass Nickel-plated brass or chromium plated brass bodies, nickel plated brass ball and PTFE seats. With either lever or butterfly operating members. Some models incorporate a stainless-steel filter. Compression models for use with copper pipe manufactured to EN 1057. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The MV10-11240 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. The MV10-11202 range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of spherical valves with bronze bodies incorporating a brass or stainless-steel ball with PTFE seat. The ART 340 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The VAB501 range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C.
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with (bronze or brass bodies) incorporating a brass or stainless-steel ball with PTFE seat. The BVBZ range - Maximum operating pressure - 40 bar. Maximum operating temperature 85°C. The BVBR range - Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range of plastic bodies spherical valves (black, white and grey) incorporating either a screwdriver slot, lever or handwheel operating member (model specific). The pushfit connections are for use with DM LLDPE tubing (not supplied) and PEX barrier pipe (manufactured to BS7291-3). When used with DM LLDPE tubing (not supplied) the supplied black or grey pipe inserts must be installed. When used with PEX barrier pipe the supplied beige pipe inserts must be installed. Maximum working pressures and temperatures: When used with DM LLDPE tubing: 6-15mm and ¼”-½” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. When used with PEX Barrier pipe (manufactured to BS7291-3): 15-22mm, 5/8” and 7/8” pushfit: 12.0 bar, cold water use only and 7.0 bar @ 65°C. Fittings which incorporate 10mm barb connections: 12.0 bar, cold water use only. Fittings which incorporate ½” - ¾” barbed end connections are open outlet use only.
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of non-rising spindle gate valves with DZR brass bodies. Operating members are either handwheel operated or lockshield. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of stop valves with either DZR brass or brass bodies (see models) with T-type operating members. The 15mm, 22mm and 28mm compression sizes are for use with copper pipe (manufactured to EN 1057). The 20mm and 25mm compression sizes are for use PE pipes (manufactured to EN 12201-2). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of bronze double regulating valves. Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with bronze bodies and DZR brass bonnets. Maximum working pressure 20.0 bar. Maximum operating temperature 85⁰C.
Range of double regulating valves with DZR brass, products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line electrolytic scale reducer with chromium plated copper body for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
‘Rashmi Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/002', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Uniseal WS 3400'. Beige coloured, calendered fibre gasket material. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio
'H.B. Fuller UK Silicone Spray'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 4', dated '23/05/2025'. For use with water up to 85°C.
'Grivory HT1VA-4 FWA (Natural) & Grivory HT1VA-4 FWA black 9225'. Natural (appears beige-green coloured) & black, injection moulded nylon materials. For use with water up to 85°C.
'TYPLEX 4055'. White coloured (opaque), extruded Polybutene-1 material. For use with water up to 85°C.
'SABIC® Vestolen A RELY 5924 R 10000 (Black)'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'Born2Bond Aquafast Instant Adhesive'. Clear sealing compound. Apply as per manufacturer's TDS dated 'April 2022' and cure for 24 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193745 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 65 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
'BENVIC IR712ES/9738' & 'BENVIC IR745ES/9738'. Grey coloured, compression moulded PVC materials. For use with water up to 23°C.
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes, see model) with a pull-out spout. The product is designed to dispense near boiling filtered water or filtered water using a ½ turn ceramic disc headwork, (¼ turn anticlockwise via a spring loaded lever for near boiling water, and ¼ turn clockwise for filtered water). The product also incorporates a ceramic cartridge headwork for hot and cold supplies with a single lever operating member. The pull-out spout incorporates a plastic aerator for the hot and cold water pathway and an integral brass insert for the near boiling/filtered water pathway. Maximum working pressure 8.0 bar. Maximum operating temperatures: 85°C, and 98°C for the near boiling/filtered water pathway (after the boiler).
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies, various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Depending on model the products are supplied with either a stainless steel braided PEX lined flexible hose assembly with 15mm spigot end connection or 10mm copper tail (see models). Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Bottom entry BS1212 part 4 (2016) compact type float operated inlet valve for WCs flushing cistern having a plastic body and adjustable float and plastic filter at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)he shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator, and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a non-rising spindle headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member. Each inlet incorporates a combined washer and stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of floor mounted, single hole, single outlet, swivel combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of shower kits with a shower hose, handset and shower rail. Maximum operating temperature 60 °C. Open outlet use only.
Range of wall mounted shower kits. Comprising of brass bodied wall mounted shower outlet, shower hose and handsets (various finishes), incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 3.5 bar. Maximum operating temperature 60*C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates a lever operated spherical valve and stainless-steel strainer. For use with BS EN1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of one piece (black) plastic storage cisterns supplied with a screened vent. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-1 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-2 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No | ||||||
| D30PF-3 | 16 bar | 85 °C | HENT, WRAS, date of manufacture (DD/MM/YYYY) | Body | No |
D30PF and D30PF-1 only different in the color of Item 11 and Item 13 D30PF-2 and D30PF-3 only different in the color of Item 11 and Item 13 DN30PF and D30PF-2 only different in the shape of Stem
Range of deck mounted ceramic cartridge and single sequential headwork assemblies, (brass bodies – various styles and finishes), incorporating a range of operating members. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of quarter turn ceramic discs headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of thermostatic cartridges with plastic bodies and stainless-steel filters, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C
Thermostatic cartridges incorporating plastic bodies, for insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-down spray type incorporating a push button. The connection to the pull-down hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). incorporating a ceramic cartridge and single lever operating member with a spring loaded, pull down trigger operated spray. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8142KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8122KP-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| F8142KPM-** | Various | 1/2" captive nut | 10 bar | 60 °C | LANBIAO | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
1）Model No. without Suffix-Chrome 2) -**Represents the following different surface treatments: 1. H-Black 2. DYB - Matte white 3. BZ - Perl white painted 4. HGTS - Red bronze 5. HTL = Yellow bronze brushed 6. Q = Bronze 7. QTSL = Bronze brushed bright 8. QTS = Bronze brushed matte 9. STS = Acid copper brushed 10. SDMGJ = Water plated rose gold 11. N = Nickel brushed bright light 12. NP = Nickel brushed 13. TJ = Titanium gold 14. TJLS = Titanium gold brushed 15. G = Gold 16. GJS = Gold brushed 17. GJSY = Zirconium gold wire drawing matte 18. PGJFY = Zirconium gold wire drawing matte bright light 19. PLSJ = Brushed gold 20. LSJY = Brushed gold matte 21. MGJ = Rose gold 22. MGJL = Rose gold brushed 23. DMGJ = Light rose gold brushed 24. HTS = Red bronze brushed 25. QHP = Grey 26. LSQH = Grey brushed 27. LHMGJ = Brushed yellow rose gold 3) The finish is on metal body
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 12101246 | Various | 1/2" captive nut | 10 bar | 65 °C | EASO | Rear of body | No | 1/4 Turn ceramic disk | Nut with screws | Aerator |
Chrome plated, Brushed brass, Brushed nickel or Matt black
Single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a quarter turn ceramic disc headworks and single lever operating members, with a pull out spray retained within a holster. The spout outlet incorporates a plastic aerator and the spout incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (swivel) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8125KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8145KP | Various | BSP 3/4" (M) | 10 bar | 85 °C | “LANBIAO” | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold 3) The finish on metal body
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T10105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T20405 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21005 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T21205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T30605W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T31505 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40105W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T40205 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| SL-T40415 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T50805 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
1.The model number suffix without B indicates chrome plated. The model number suffix with B indicates black. The model number suffix with BB indicates Brushed brass. 2.Only SL-T40415, SL-T40205 & SL-T40105W suffix with G indicates Champagne Gold.
Range of wall mounted, two-hole single outlet combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Wall mounted two-hole, single outlet (fixed) combination tap assemblies, (brass bodies -various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41105 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
The model without a suffix indicates chrome. The model number with suffix B indicates black. The model number with suffix BB indicates Brushed brass.
Wall mounted thermostatic blending valve (brass body, various finishes - see model) incorporating a 2-way ceramic disc headwork with a single lever operating member controlling and diverting the flow between the spout outlet or the shower outlet. Temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 16.0 bar. Maximum operating temperature 75°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with lever type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M5005 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall mounted, two-hole, single outlet (fixed) bath/shower mixers, (brass bodies – various finishes). Incorporating a thermostatic cartridge controlling the temperature and a manual diverter controlling the flow between the outlets with dome type operating members. The spout outlet incorporates a plastic aerator. Both inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Two hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products Incorporate either a non-rising spindle (model 1641 only) or quarter turn ceramic disc headworks (all other models) with either cross top (model 1641 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a a pop-up waste not verified by test. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (DZR brass main body - various finishes) incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted three-hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating a quarter turn ceramic disc headwork with cross top operating members. The spout outlet incorporates a a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Range of water filters with a plastic body and plastic filter. The products are supplied with a spherical valve, which acts as a drain valve. This is provided loose for the installer to attach, or for models added July 2025 it can also be factory applied. Maximum working pressure 6.0 bar. Cold water use only.
Range of filter shower handsets and tap outlets with plastic bodies with EPDM O-Rings Open Outlet use. Maximum operating temperature 60°C
Range of plastic filter heads and housings. Maximum working pressure 8.6 bar. Cold water use only.
‘GM50xx’ range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *- STPT304 and *- STPT316 stainless steel pipes. The GM5004 prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
‘Uponor Q&E’ range of brass press-fit fittings for use with PE-Xa-PE-PE ‘Uponor Aqua Pipe AU’ multi-layered pipes. Maximum operating pressure 10 bar. Maximum operating temperature 70°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with MONFLEX PEXB/AL/PEXB MULTILAYER PIPES. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘EPH_WSP19_XXXX’ range of brass caplillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Flowflex,’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of compression fittings with brass, chrome plated brass bodies. COM RANGE OF COM For use with copper pipe (EN 1057) Maximum operating pressure 16 bar. Maximum operating temperature 85°C
CORE “SB DZRCOM” range of DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The tank connectors incorporate a NBR gasket. The straight tap connectors incorporate a blue fibre gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Instantor Lead-Free Brass’ compression fittings with DZR brass body, for use with DZR Copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Twistloc’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
‘EPH_WSP19_XXXX’ range of brass end feed and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of WC dual flush drop valves with an ABS body and silicon seal. The valves are operated via a push button assembly for either full or reduced flush and incorporate an internal adjustable height overflow. Cold water use only. Open outlet use only.
Range of urinal autosyphons with plastic body and supplied with plastic backnuts.
Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.
‘WS’ range of water meters with brass bodies, incorporating plastic impellers. The inlets incorporate plastic filters. Maximum working pressure 16 Bar. Maximum operating temperature 50°C.
Range of water meters with black nylon bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of SSM-AQUO ultrasonic water meters with brass bodies, the inlets incorporate a plastic filter. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.
Range of angled valves with chromium plated brass bodies, incorporating a non-rising spindle headwork or a quarter turn ceramic disc headwork with either triangle, cubic, single lever or dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
’TP Series 300’ and ‘TPE Series 300’ ranges of single stage in-line pumps with black coloured cataphoretic electro deposition coated cast iron or ductile iron bodies and bronze, stainless-steel or black coloured cataphoretic electro deposition coated cast iron impellers. Pumps are available with BQQE or BBQE shaft seals. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of shower handsets and overhead showers with plastic bodies incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
Range of shower handsets and overhead showers with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
Range of wall or ceiling mounted shower outlets with chromium plated bodies (or black body for 22123KF0) consisting of showers arms and shower head for installation with specific rough-in sets. Shower head bodies incorporate approved single check valve cartridges, however, the complete assemblies have not been tested to demonstrate it provides backflow protection. The 26.484 model rough-in set incorporates a plastic flow regulator on the inlet. Maximum working pressure: Open Outlet. Maximum operating temperature: 60°C.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless-steel filter and a plastic flow regulator. Maximum working temperature 45°C. Open outlet use only.
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of Y-patterned strainers with brass bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
410714 Modena & 161633 Kubic ranges of pillar taps (brass bodies – Chrome finish) incorporating a quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar, Maximum operating temperature 65°C.
Range of pillar taps, incorporating a non-rising spindle headwork with dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps are supplied with an optional flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted self-closing taps (chromium plated brass) with a dome type operating member. The SCHELL PETIT SC - 02 147 06 99 model incorporates a screwdriver operated servicing valve on the inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Range of stainless steel braided EPDM lined flexible hose assemblies with EPDM seals & EPDM washers, available with a variety of end connections. For use with copper pipe manufactured to EN1057 & HEP20 PB pipe. Maximum working pressure; 6 Bar Maximum operating temperature; 65°c
Range of concealed, thermostatic blending valves with 2 or 3 shower outlets, incorporating a thermostatic cartridge controlling the temperature that incorporates a manual override button and ceramic disc diverters or quarter turn ceramic disc headworks controlling the flow. The products incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of T-type thermostatic mixing valves with brushed chrome plated DZR brass bodies and manually adjustable temperature control. The inlets of the press fit and push fit models incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Press fit and push fit connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of T-type thermostatic mixing valves with brushed chrome plated DZR brass bodies. Each inlet incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression connections are for use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted self-closing thermostatic shower valves with brass bodies, with a chrome plated dome type operating member. Models are also supplied with a chrome plated shower head with a plastic aerator. Both inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, thermostatic shower valves, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with dome type operating members, the inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and a stainless-steel strainer. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Shower set comprising of a wall mounted shower valve, riser rail, shower handset, shower hose and overhead shower outlet. Flow in controlled by a ceramic disc headwork with dome type operating member. Temperature is controlled via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Each inlet of the shower valve incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted, concealed, thermostatic shower valves, (brass bodies - various trim set finishes), incorporating quarter turn ceramic disc headwork with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The products incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate that is provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic blending valves with brass bodies (various finishes). Incorporating either 2-way ceramic disc diverters (2 on, 1 off) that also controls the flow (model DB3100.a.bbb) or with a ceramic disc headwork that controls the flow only to a single outlet (model DB3200.a.bbb.). Both incorporate lever type operating members. The temperature is controlled independently via a thermostatic cartridge with lever type operating members. Inlets incorporate approved check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of Shower Valves with thermostatic temperature control. Wall Mounted Concealed. Inlets incorporate approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum temperature 85°C Miximum pressure 5.0bar.
Range of gear operated butterfly valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16 Bar Maximum operating temperature 80°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with (blue epoxy coated) ductile iron bodies and cast iron discs incorporating EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Equilibrium float valve with brass body, brass float arm and EPDM seals. Float not supplied and not covered under the scope of this approval. Maximum working pressure 10.0 Bar Cold water use only
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of tilting disc non-return valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. 447 70 models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. Maximum operating temperature 60°C.
Range of pilot operated pressure reducing control valves with blue or grey epoxy coated ductile steel bodies. Maximum supply pressure: 20.0 bar. The product is available with the following adjustable outlet pressures: between 1.0 and 7.0 bar or between 4.0 and 12.0 bar. Maximum operating temperature: 85°C.
Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range of normally closed (NC), solenoid valves with plastic bodies and EPDM diaphragm. Models with push-fit connections are for use with copper pipe (manufactured to EN 1057) and PTFE pipe. The products incorporate a plastic or stainless steel filter on the inlet, (except for models with swivel nut, push-fit and nozzle inlets, as well as the 44.007.126 and 01.021.126 models) . The 44.007.126 model incorporates a Y-pattern stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperatures: Cold water use only, 65°C or 90°C for models marked with ℗ - Please consult model section for further details.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range lever operated spherical valves with nickel plated brass bodies and chromium plated brass balls. The 1792 model compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of angled spherical valves with chromium plated brass bodies and ball. The AGV1734 model is lever operated, the AGV1834 model has a ‘T’-handle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies (chromium plated), chromium plated brass balls, PTFE seat and single lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. DN50 to DN500 sizes are operated by handwheel. DN600 to DN800 sizes are operated by a gear box. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves, brass body and disc with a handwheel operating member. Maximum working pressure 20.0bar Maximum operating temperature 100°C
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
Range of in-line electrolytic scale reducers with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
'HP204AD'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Endolac® 245.10'. Factory applied, black coloured bituminous paint. Apply as per manufacturer's TDS 'Version edit: 17/04/2024'. Cure for 7 days at 20°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Greasil 4000'. White coloured silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Arctic Hayes Silicone Spray (code: PH040)'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's packaging instructions. For use with water up to 85°C.
'ISO Resin Topaz-2100-AT'. Beige coloured polyester resin manufactured by hand layup. For use with water up to 45°C.
'GP Resin Topaz-1110-TP'. Beige coloured polyester resin material manufactured by hand lay-up. For use with water up to 45°C.
'TP14371'. Blue coloured polyethylene material manufactured by roto-moulding. For use with water up to 85°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
'BAILUN PPR Pipe (PPR0411)'. White coloured, extruded PPR pipe. For use with water up to 85°C.
'N57140'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘40SIL310P, 45SIL310P, 50SIL310P(W), 55SIL310P, 60SIL3137P, 65SIL310P, 70SIL310P, 75SIL310P & 80SIL310P'. Compression moulded, silicone rubber ‘O’ rings in natural, white, black, red, blue, yellow & grey. Tested in-radius size 0.5mm. For use with water up to 85°C.
'Silopren LSR 2742'. Colourless (translucent), compression moulded silicone elastomeric material. Shore hardness 38. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Weld-On 748 ECO™ Blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer’s TDS ‘748 ECO-09-2024’. ‘Weld-On 748 ECO™ Clear PVC Solvent Cement’ was added to the approval in March 2026. Clear solvent cement. Apply as per manufacturer’s TDS '748 ECO-07-2025'. Cure for 12 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Grilamid TR 30 natural, TR 30 LS natural (appear colourless, translucent), TR 30 LS blue 4345, TR 30 LS blue 4387 & TR 30 LS blue 4396 (blue coloured)’. Injection moulded, PA 61/X materials. For use with water up to 85°C.
'BLAZEMASTER® 88065 Orange 734 M PEL 8065OMAM'. Orange coloured, injection moulded c-PVC fittings. For use with water up to 23°C.
'BLAZEMASTER® 88738 ORG 734 M PWD 8738OMAL Pipe'. Orange coloured, extruded c-PVC pipe. For use with water up to 23°C.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 Bar. Cold water use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 440 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 71 450 xx0 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Hansgrohe | Operating Member | Yes | Ceramic cartridge | Not Applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HNHS40-Black | Various | 1/2" F | Open Outlet bar | 65 °C | Waterworks logo | Shower handset | No | None | Shower Hose, Handset, | ||
| HNHS40-Grey | Various | 1/2" | Open Outlet bar | 65 °C | Waterworks Logo | Shower Handset | No | Shower Hose, Handset, |
Finishes Available - Brass, Chrome, Nickel, Burnished Brass, Matte Nickel, Brass/Dark Nickel, Copper, Dark Brass, Dark Nickel, Vintage Brass, Gold, Matte Gold
Range of hand showers and shower arm kits with (brass bodies - various finishes. The inlets of the hand showers and the inlet elbows incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Open outlet use only. Maximum operating temperature 65°C.
Range of wall mounted shower valves (brass bodies – various finishes) incorporating a self-cancelling diverter with a ceramic cartridge headwork controlling flow and temperature and a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH72 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH73 | 1/2" | 6 bar | 65 °C | Waterworks | Body | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH62 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable | ||
| GUTH63 * | 1/2" | 6 bar | 65 °C | Waterworks | Body and tile guard | No | Not applicable | Not Applicable | Not Applicable |
Product Identification(s) with an * as suffix = models added 11/08/2025
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies models HVDCVC-31, HVDCVC-32 are chrome plated. Maximum working pressure 16 Bar Maximum operating temperature 60°C
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of In-line plastic flow regulators housed within a brass bodies incorporating a plastic strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Some models incorporate a stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AB-2047-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2053-F | 33.6 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2057-F | 26.8 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-F | 27.5 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2058-S | 27.2 mm Ø | 24 bar | 85 °C | Xingle | Body | No | |||||
| AB-2059-F | 34.0 mm Ø | 24 bar | 85 °C | Xingle | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TM001 | Black | Ø 33.81mm | 5 bar | 85 °C | Company logo and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable | |
| TM006 | Black | Ø 26.66mm | 5 bar | 85 °C | Company logo, Sedal and date of manufacture (DD/MM/YY) | Body | No | Not applicable | Not Applicable | Not Applicable |
Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T21002L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21002M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T31502M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T21202L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T50802L | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802M | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T50802 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Open Outlet | |
| SL-T10102 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Filter | |
| SL-T20402 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| SL-T40202 | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| SL-T40102W | Various | M10*1 | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | C-plate | Flow Straightener |
Various finish: (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass (4) Models SL-T40202 & SL-T40102W with suffix G: Champagne Gold
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AL ES BAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CRU TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313935 | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313936 | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313937 | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
Combination Tap assemblies incorporating ceramic cartridge or ceramic disc headworks.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork and cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 bar. Maximum operating temperature: 80°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQSOL EFSNK C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 4648G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288489 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288491 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311098 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 3311102 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311106 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311162 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQMEN EFSNK BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 9087G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288493 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288503 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311105 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311114 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311125 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311164 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | C-plate |
Model added February 2026: RP3 EC SNK EF BLK
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes) incorporating 1/4 turn ceramic disk headworks and single lever operating members. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 147013 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | Non-rising spindle | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks incorporating plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 34 113 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 115 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 112 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator | ||
| 34 116 xx0 | Various | basic set G 1/2 | 10 bar | 70 °C | AXOR | On Spout | Yes | Ceramic cartridge | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish. Products to be installed in combination with 13623180 Basic set, which does not form part of this approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| LIS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| LIS BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| RP3 LIS BSM C | Chrome (Cr3) | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| ELE BSM BLK | Black | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| RP3 ELE BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Shower Hose, Handset, |
Model added February 2026: RP3 ELE BSM C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T41101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21001 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T31501 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T21201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T50801 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T30601W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T20401 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| SL-T40201 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40401R | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T40101W | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle headwork | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| SL-T10101 | Chrome plated | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AR2 THLBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| BRT AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| CN AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 AR2 THBSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disc | Metal Backnuts | Flow Straightener |
Model added February 2026: RP3 AR2 THBSM C
Range of two-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HD15 | Chrome | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15K | Matte Black | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BB PVD | Zirconium gold brushed topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BV | Brushed gold matte topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15MG | Gun gray brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15CA | Rose gold brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BN | Nickel brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
These models only different in surface treatment
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313941 | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313942 | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313943 | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
Range of three hole, wall mounted, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model) comprising of a spout outlet, a clipsed extension set for accommodating headworks and a trim set with various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH WMBAS C | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 3TH WMBAS BLK | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 3TH WMBAS BB | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS C | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS BLK | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| CRU 3TH WMBAS BB | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313938 | Chrome | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313939 | Black | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| 313940 | Brushed Brass | 15mm Compression | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 11 430 xx0 | Various | G 3/4 | open outlet bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Mingshi stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Hyddro Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Hyddro stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of Hyddro press fittings incorporating EPDM ‘O’-rings. For use with Hyddro (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass press fittings for use with copper pipe (manufactured to EN1057:2006 and +A1:2010 Seamless round copper tube, R250 half hard). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘AF’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Qmpress Instaboil Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.
Range of threaded copper pipe elbow tap unions. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of overhead shower outlets with (brass bodies – various finishes) incorporating stainless-steel filter washers at the inlet. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HS183 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS2019 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS2018 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable | |
| HS3013 XXX | VARIOUS | 1/2" BSP | N/A bar | 85 °C | PPI | ON BODY | No | Not applicable | Not Applicable | Not Applicable |
XXX Denotes the following: First, second & third different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of in-line bronze bodied ‘Y’-pattern strainers with stainless steel mesh. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-T40217 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40218 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SL-T40217W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40218W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40107W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| SL-T41107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T41108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-T40807W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808W | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42107 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42108 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40807 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40808 | Various | 3/4" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T42106 | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40806W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| SL-T40106W | Various | 1/2" BSP (M) | 10 bar | 60 °C | Company logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Aerator |
1. Various finish: (1) With suffix B: Black (2) With suffix BB: Brushed brass (3) Models SL-T40217, SL-T40218, SL-T40107W, SL-T40108W & SL-T40106W, with suffix G: Champagne Gold
CR27A Chrome Pillar tap with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. The spout incorporates a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
GE01, GE01/501, CR19 & CR19/501 Pillar taps with single lever or cross-top operating members incorporating a 1/4 turn ceramic disc headwork. Models GE01 & GE01/501 incorporate a flow straightener. Maximum pressure 10 bar. Maximum temperature 60 °C
Range of EPDM hoses with either nylon or stainless-steel braiding, with or without a PVC sheath. Some models incorporate isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic shower valves (brass body – various finishes), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHC3DIV C | Chrome | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic shower valves with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with single lever operating members. Temperature is controlled by a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating a 2-way manual diverter to control the flow with cube type operating members. The temperature is controlled independently via a thermostatic cartridge with cube type operating member that incorporates a manual override button. The inlets incorporate stainless-steel strainer and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies. Maximum inlet supply pressure 8.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. ½”, ¾”, 1” & 1¼” size have inspection ports on the outlet only. 1½”, 2”, 2½”, 3” AND 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with DZR brass bodies. Handwheel operated. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630LT'. Factory applied, two-part, white coloured epoxy coating. Mix base and cure agent in a 3:1 volume ratio and apply as per manufacturer's PDS dated November 2024. Cure for 3 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'H-451PW'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user manual 'TWJ/H--451PW-20250120', dated 'January 1, 2025'. Cure for 7 days for 25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'4300051 PVC Inner Hose (black coloured), 4300052 PVC Inner Hose (white coloured) & 4300053 PVC Inner Hose (blue coloured). Single layered, extruded PVC hoses. For use with water up to 65°C.
'Sanibiw Dynamic'. Multi-layered, extruded hoses comprising of an off-white, transparent silicone inner layer, white, opaque PES yarn reinforcement layer and black coloured, silicone outer layer. The inner layer has a tested in-radius size of between 0.4mm & 0.8mm. For use with water up to 85°C.
'flomasta Silicone Spray'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's TDS, 'issue 4', dated '23/05/2025'. For use with water up to 85°C.
'T-NO.100S-FD'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
'Bondrite S1010'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per TDS, issue date November 2021. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'EPDM 70.54-02 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EPDM 70.54-02 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Flexrubber EW70 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘ELASTOSIL® R’ solid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 1.0mm. The following grades are natural and are for use with water up to 85°C. E indicates ELASTOSIL® AUX Crosslinker E. C1 indicates ELASTOSIL® AUX Crosslinker C1. Grades for extrusion and press moulding: R 401/20 E (shore hardness 20), R 401/30 E (30), R 401/40 E (40), R 401/50 E (50), R 401/55 E (55), R 401/60 E (60), R 401/70 E (70), R 401/80 E (80) & R 401/90 E (90). R 402/60 E (shore hardness 60), R 401/65 E (65) & R 401/75 E (75). R 420/30 E (shore hardness 30), R 420/40 E (40), R 420/50 E (50), R 420/60 E (60) & R 420/70 E (70). Grades for press moulding: R 401/20 C1 (shore hardness 20), R 401/30 C1 (30), R 401/40 C1 (40), R 401/50 C1 (50), R 401/55 C1 (55), R 401/60 C1 (60), R 401/70 C1 (70), R 401/80 C1 (80) & R 401/90 C1 (90). R 402/60 C1 (shore hardness 60) & R 402/75 C1 (75). R 420/30 C1 (shore hardness 30), R 420/40 C1 (40), R 420/50 C1 (50), R 420/60 C1 (60) & R 420/70 C1 (70). R 420/30 C1 & R 420/70 C1. The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT Yellow RAL 1021. PT Yellow RAL 1016. PT Red RAL 3000 F. PT Red brown RAL 3013. PT Light brown RAL 8003. PT Dark brown RAL 8015. PT Green RAL 6017. PT Ultramarineblue RAL 5002. PT Light blue RAL 5015. PT Grey RAL 7040. PT Deep black RAL 9005. PT Black RAL 9017. PT White RAL 9010.
ELASTOSIL® LR liquid silicone rubber materials. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural (appear white, opaque) and are for use with water up to 85°C. Grades for injection moulding: LR 3003/10 TR A+B & ELASTOSIL LR 3003/20 TR A+B. LR 3071/40-60 A & B (40 - 60). LR 3003/30-80 A & B (30 - 80). LR 3004/20-70 A & B (20 - 70). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: FL yellow RAL 1016. FL orange RAL 2004. FL Red Brown RAL 3013. FL dark blue RAL 5010 & FL light blue RAL 5015. FL grey RAL 7000. FL carbon black RAL 9005. FL black RAL 9011. FL white RAL 9010. FL Red RAL 3000 F. FL Orange 2004 F. FL Light Blue 5015 F. FL Black 9005 F. FL green RAL 6010. ELASTOSIL® R plus platinum catalysed HTV silicone rubber. The number in brackets indicates shore hardness. Tested in-radius size 0.8mm. The following grades are natural and are for use with water up to 85°C. Grades for injection and press moulding: R plus 4001/40-80 (40 - 80). Grades for extrusion: R plus 4305/40-80 (40 - 80). The products may be coloured using the following ELASTOSIL® pigment pastes, also for use with water up to 85°C: PT yellow RAL 1016. PT orange RAL 2004. PT dark blue RAL 5010 & PT light blue RAL 5015. PT carbon black RAL 9005. PT white RAL 9010.
'WEICONLOCK AN 301-72 (white coloured) & WEICONLOCK AN 301-48 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'ONEBOND ADHESIVO PVC PROFESIONAL'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On® 773™'. Dark grey coloured solvent cement, intended to join ABS pipe and fittings. Apply as per manufacturer's data sheet '773-07-2025'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On® 795™'. Clear solvent cement, intended to join PVC pipe and fittings. Apply as per manufacturer's data sheet '795-07-2025'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, double outlet (fixed) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied). All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Near-boiling circuit has a maximum operating temperature 98°C. Hot-water circuit has a maximum operating temperature of 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| GUTH71 | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk | |||
| GUTH61 * | Brass | 1/2" NPT (M) | 6 bar | 65 °C | Waterworks | Body | No | 1/4 Turn ceramic disk |
Product Identification with an * as suffix = models added 11/082025
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 812003A | 23.8mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812038A | 23.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812049A | 19mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable | |||
| 812056 | 18.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812057 | 19.0mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812072 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812073 | 24.3mm | 10 bar | 85 °C | GAOAO | Body | No | 1/4 Turn ceramic disk | Not Applicable | |||
| 812114 | 18.5mm | 10 bar | 85 °C | GAOAO | Body | No | 1/2 Turn ceramic disk | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30D-9 | 29.91mm | 10 bar | 85 °C | WANHAI, WRAS, 30D-9, Production date (DD/MM/YYYY) | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 233308 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 Bar Maximum operating temperature: 65°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies -various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various styles and finishes) incorporating ceramic cartridge headworks, and single lever operating members. The spout outlets incorporate a plastic or metal aerator. The products are supplied with click type pop-up wastes (not verified by test). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating members. The spout outlet incorporates a plastic flow aerator. Maximum working pressure Bar 10.0 Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B002* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | Body | No | 1/4 Turn ceramic disk | C-plate | Aerator | |
| B003* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | Body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
* denotes finish and can be replaced by: C - Chrome, RG - Rose Gold, BTG - Brushed Titanium gold, BZG - Brushed Zirconium gold, BRG - Brushed Rose gold, MW - Matte white, BS - Brushed stainless, BN - Brushed nickel, PN - Polished nickel, GM - Gunmetal, B - Matte black, TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| QST SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| RP3 DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disc | C-plate | Flow Straightener |
Model added February 2026: RP3 DUL SNK EF C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating either a ceramic cartridge headwork or quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator (LEV104 and FARO104 models) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
Range of single hole, double outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever or non-rising spindle headworks with cross top operating members (see model). The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with metal backnuts. Maximum working pressure: 5 Bar Maximum operating temperature: 65°C.
Range of wall mounted, two-hole single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 Bar Maximum operating temperature: 65°c
Range of two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. Maximum working pressure Bar 10.0 Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B001* | Various | ½" BSP (F) | 5 bar | 65 °C | WINSDRUM | Decorative plate | No | Ceramic cartridge | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome, RG - Rose Gold, BTG - Brushed Titanium gold, BZG - Brushed Zirconium gold, BRG - Brushed Rose gold, MW - Matte white, BS - Brushed stainless, BN - Brushed nickel, PN - Polished nickel, GM - Gunmetal, B - Matte black, TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FRZ BSM C | Chrome | 3/4" BSP (M) | 10 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| RP3 MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| HMS MIO BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| CN SPH BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
Two hole, single outlet (fixed) combination tap assembly. Incorporating quarter turn ceramic disc headworks with single lever operating members and manual diverters to shower outlets. The spout outlets incorporate plastic flow straightener. This approval includes a hose & handset and the products are supplied with metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T41061 | Chrome plated | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/2 Turn ceramic disk | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| IRS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| OPS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T41001 | BSP 3/4" (F) | 10 bar | 60 °C | Company logo | On diverter cap | No | 1/4 Turn ceramic disk | Aerator | |||
| T41002 | BSP 3/4" (F) | 10 bar | 60 °C | Company logo | On diverter cap | No | 1/2 Turn ceramic disk | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH WMBF C | Chrome | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| AL 3TH WMBF BLK | Black | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| AL 3TH WMBF BB | Brushed Brass | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF C | Chrome | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF BLK | Black | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener | |
| CRU 3TH WMBF BB | Brushed Brass | 15mm Compression | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
Range of three-hole, brass bodied, single outlet (fixed) combination tap assemblies available with various finishes (see models). The products incorporate either a non-rising spindle (models 1648 and 1881 only) or quarter turn ceramic disc (all other models) headworks with either cross top (models 1648 and 1881 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts and lever operated pop-up wastes. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of copper and bronze capillary brazed fittings for use with copper pipe manufactured to EN1057:2006 +A1:2010 Maximum pressure 10.0 Bar (54mm up to and including 108mm) Maximum pressure 2.0 Bar (Over 108mm up to and including 159mm) Maximum operating temperature 100°C.
Range of M profile copper press fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
N·U Range of stainless steel (304S31/316S11) press fittings for use with N·U series 1 & 2 stainless steel (304S31/316S11) pipe. The fittings and tube are assembled using a crimping tool. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘ISR’ range of copper, DZR brass or gunmetal capillary, lead free solder ring and threaded fittings for use with copper pipe. (Products YP62, YP63, YP63L, YP64, YP68, YP68FF, YP69, YP69F & YP69P Maximum working pressure - 16 bar Maximum operating temperature - 65C All other fittings Maximum working pressure - 16 Bar Maximum operating temperature - 95°C.
Range of compression fittings incorporating polypropylene bodies, plastic pipe liners, plastic grip rings and EPDM seals. For use with PE100 pipe manufactured to BS EN 12201. Maximum working pressure: 16Bar. Maximum operating temperature: 23°C
Range of Victaulic rigid couplings (905, H10, H11, H20, H50) for use with plain end HDPE pipe (EN 12201-2), and for product 907, for use with EN 12201-2 HDPE and EN 10217-1 steel pipe. For above and below ground use. Maximum working pressure: SDR7.4 25bar, SDR11 16bar or SDR17 10bar. Maximum operating temperature: Cold water use only.
Range of polypropylene push-fit fittings and inserts for use with PE80 MDPE pipe (manufactured to BS EN 12201). For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of metric and imperial PVC-U Solvent cement or Threaded fittings for use with PVC-U pressure pipe Class E manufacture to BS EN 1452 Maximum working pressure; 16 Bar Maximum operating temperature; Cold water only
Range of WC dual flush drop valves with ABS bodies and silicon seals. The valves are operated via a push button assembly for either full or reduced flush and incorporate an internal, adjustable height overflow.
Range of ultrasonic water meters with brass bodies and EPDM O-rings. The inlets incorporate a double check valve assembly, verified by test - suitable for backflow protection against Fluid Category 3. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ultrasonic water meters with brass/plastic bodies. The inlets incorporate plastic strainers and brass spherical ball valves. Maximum working pressure 16.0 bar. Maximum operating temperature 50⁰C.
Range of ultrasonic water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85⁰C.
Range of pressure transmitters gauge pressure measurement devices and differential pressure measurement devices with either stainless steel or Hastelloy or Monel bodies. Maximum working pressure 66.0 Bar Maximum operating temperature 85.0°C
Range of heat interface units providing heating and instantaneous hot water. The central heating and hot water are generated via plate heat exchangers. The central heating circuit contains a pressure relief valve (3.0 bar) and an expansion vessel. The cold inlet supply to the plate heat exchanger incorporates an in line single check valve assembly, (suitable for backflow protection against Fluid Category 2). Max Temperature & Pressure for models A/7892284 & B/7892283: Primary Circuit: 6.0 bar at 90°C DHW Circuit: 10.0 bar at 55°C Secondary Circuit 6.0 bar at 90°C Max Temperature & Pressure for all other models: Primary Circuit: 16.0 bar at 90*C, DHW Circuit: 10.0 bar at 65*C, Secondary Circuit 3 bar at 85*C.
Range of shock arrestors with a stainless-steel body and EPDM liner. The compression connection of the X2041.015 model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Shock arrestors with a copper body, plastic shuttle and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The DPV(M/S) models and DPV(S) models can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Existing models: DPV models 10.0 bar, DPVM models with an oval flange or VME models with integral check valve 16.0 bar, All other DPVM models 25.0 bar. DPV(S) models with an oval flange or DPV(S)(E) models with integral check valve 16.0 bar, All other DPV(S) models and DPH(S)I models 25.0 bar. Maximum operating temperatures: DPHM, DPVE and DPVME models with integral check valve 60°C, all other model variants 100°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
A range of variable speed booster pumps with stainless steel bodies and impeller. Maximum working pressure: 8 bar. Maximum operating temperature: 35°C.
Range of interlocked EPDM lined shower hoses assemblies with EPDM gaskets. Maximum operating temperature: 85°C Open outlet use only.
Range of shower handsets and headsets with chromium plated plastic bodies. Models P60901 and P61400 have check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum working pressure: Open outlet. Maximum operating temperature: 60.0°C.
Range of fixed shower arms, (brass bodies - various finishes) with EPDM O-Rings. Maximum operating temperature: 85°C, open outlet use only.
Range of shower arms with brass bodies. Models 91xx7034 & 91xx9323 incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 80.0°C (models 86xxxxxx) or 60.0°C (models 91xxxxxx)
Range of wall mounted shower outlets (chromium plated brass). Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of (chrome plated) plastic shower handsets with flexible shower hose and stainless-steel braided connection hose. The inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C. Open outlet use only.
Overhead shower (plastic body – various plated finishes) incorporating a flow regulator and stainless-steel strainer washer. Open outlet use only Maximum operating temperature 85°C.
Range of In-line ‘Y’ strainers with ductile iron bodies (blue epoxy powder coated) and stainless-steel mesh. Maximum working pressure 10.0 Bar Maximum operating temperature 80°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of draining taps, straight or elbowed with brass bodies incorporating a rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 95.0°C
Range of drain off taps incorporating DZR brass bodies and non-rising spindle operating mechanisms. D340 range incorporates lockshield mechanisms and the D341 range incorporates key operated mechanisms. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of pillar taps (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure Bar 10.0 Maximum operating temperature 65°C.
Wall mounted non-concussive tap assembly (chrome plated brass body) with a dome operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 75°C.
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic aerator and the products are supplied with metal backnuts. Model 68400 incorporates a manual temperature lever. Maximum operating pressure 10 bar. Maximum operating temperature 65°C.
Softpex® Range of Stainless Steel and Polyamide braided, PE lined connection hoses with various end connections DN6 (S/S & PA braided – PE-RT) , DN8 (S/S & PA braided – PEX), DN10 (S/S braided - PEX ONLY), DN13 (S/S braided - PEX ONLY) Maximum working pressure; 10 Bar Maximum operating temperature; 70°c
Range of nylon braided flexible outlet hoses, incorporating an EPDM liner, EPDM ‘O’-rings and gaskets. Maximum operating temperature 85°C.
Range of air venting valves with brass bodies. The P0508.015 compression model is for use with copper pipe (manufacturer to EN 1057) Maximum working pressure: 10.0 bar. Maximum operating temperature 85°C.
Range of air venting valves with blue epoxy coated ductile iron or plastic bodies with plastic floats. Maximum working pressure 16.0 Bar. Cold water use only.
Range of automatic air release valves with blue epoxy coated stainless steel bodies and plastic or stainless-steel floats. Maximum working pressure 16.0, 25.0 or 40.0 bar (See Models below). Cold water use only.
Range of wall mounted, concealed, manually operated blending valves with (brass bodies - various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks and single lever or dome type operating members. Maximum working pressure 5.0 Bar Maximum operating temperature 70 °C.
Wall mounted thermostatic shower valve (chromium plated brass) incorporating a quarter turn ceramic disc headworks with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with manual override button and a single lever operating member. Both inlets incorporate an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall mounted shower valve (various finishes) incorporating a quarter turn ceramic disc headwork controlling flow on/off and to either the overhead shower or the handset (CAM-149T-RRK-XXX). Temperature is controlled via a thermostatic cartridge with a manual override button. The inlets incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 5bar. Maximum operating temperature: 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| E80018 | Chrome | 15mm | 5 bar | 60 °C | ESTEEM | Handle | No | Non-rising spindle | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
Range of wall mounted thermostatic mixing valves (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature using a single lever operating member. Inlets incorporate servicing valves and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wafer and lug butterfly valves incorporating blue epoxy coated ductile iron body, either a stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron disc and an EPDM seat. DN40-300 lever and gear operated, DN350-600 gear operated. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of combined temperature and pressure relief valves incorporating DZR brass bodies and an EPDM diaphragm. Valves incorporate a manually operated rotational easing gear. The valves are pre-set at 6.0 or 7.0 bar (see models). Compression connections are for use with copper pipes (manufactured to EN 1057). Maximum operating temperature 90°C.
Range of combined temperature and relief valves incorporating DZR brass bodies and PTFE washers. Valves incorporate a manually operated rotational easing gear and can be supplied pre-set at 6.0 bar, 7.0 bar, 8.0 bar or 10.0 bar. Compression outlet connections are for use with copper pipe (manufactured to EN1057, R250). Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
UNIWAT 5107Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A swing gate, resilient trim, non-return valve with blue epoxy coated ductile iron body. Maximum working pressure: 25bar Maximum operating temperature: 85°C.
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of adjustable in-line pressure reducing valves with bronze bodies, stainless steel strainers and manually operated pressure reducing mechanism. Outlet pressure adjustable between 1.5 to 6.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 60°C.
Range of normally open (L282 prefix models), normally closed (L182 models) or latching (61 suffix models) solenoid valves with either brass, nickel plated brass or stainless-steel bodies and an EPDM diaphragm. Please refer to model for maximum working pressure. Maximum operating temperature 85.0°C
Range of single lever or butterfly handle operated spherical valves with chrome plated brass bodies incorporating chrome plated brass ball. Maximum working pressures: see model below. Maximum operating temperature 23°C.
Range of spherical valves with brass bodies, stainless steel (SS304) balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, chrome plated ball and PTFE seats. Not supplied with operating member. Maximum working pressure 25.0 Bar Maximum operating temperature 90 °C.
Range of angled spherical valves with (brass bodies - various finishes), PTFE seats and NBR seals. Model Art. 1251 incorporates a stainless-steel filter. Maximum working pressure 10.0, 35.0 or 55.0 Bar (see models) Maximum operating temperature 90.0°C (Art. 1251 Cold water only)
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of in-line spherical valves with a nickel-plated brass or DZR brass body, chromium plated brass or chromium plated DZR brass or stainless-steel ball and PTFE seats (see model for details). The products can be supplied with the following operating members: 1601 and 2045 ranges: single lever, single lever with extension stem kit, single lever with lockable handle or butterfly operating members. 1046 range: short black lever or screwdriver operated. The 11-1046 (1046) and 11-1015 (2045) ranges are for use with copper pipe (manufactured to EN1057). Maximum working pressures: 1046 and 2045 range: 25.0 bar. 1601 range: 40.0 bar. Maximum operating temperature 85°C.
Range of ‘EFFAST’ spherical valves with plastic bodies incorporating EPDM ‘O’-rings. For use with ABS pipe manufactured to BS 5391. Maximum working pressure: 15 Bar. Maximum operating temperature: Cold water use only.
Range of inline plastic bodied ball valves with EPDM ‘O-rings and lever operated. For use with PVC-U pressure pipe in accordance with BS EN 1452 standard Maximum working pressure. Sizes 20mm – 63mm & 1/2" – 2”: 16.0 Bar Sizes 110mm & 2 1/2” – 4”: 10.0 Bar Cold water only
Range of gate valves with brass bodies, incorporating a brass wedge. Valves are operated via a non-rising spindle headwork incorporating either a lockshield or handwheel operating member. Maximum working pressure 20.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with pipe connector and flange adapter systems with ductile blue epoxy coated bodies, EDPM wedge and PTFE gaskets. The valves operate via a hand wheel. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of bronze gate valves incorporating bronze wedges, non-rising stems. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (132, 133 and 137 prefix models). Bronze body, bronze wedge and lockshield (131 and 136 prefix models). Brass body, brass wedge and handwheel (101 model only). Maximum working pressure 20.0 bar & 25.0 bar (model 131LS-50 only). Maximum operating temperature 85°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. With Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of 2, 3 ,4 or 5 way manifolds incorporating brass bodies, stop valves and EPDM O-rings, to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (4.5, 6.0 or 8.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
BT1420-DFM Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of scale inhibitors with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'RELIBIT 1001 Coating'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's Standard Operating Procedure & Guidelines 'RP/291', '203/2024, Revision 1', dated '1st April 2024'. Cure for 10 hours@35°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's Work Instructions 'WP-08-05 I', Issue '04', Revision '0', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'3P764921 Pipe Spacer'. White coloured (opaque), injection moulded PP Pipe Spacer. For use with water up to 85°C.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'DS MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 28', dated 03.04.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NS’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 23.04.2025'. Cure for 4 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CarboStop 102/CarboStop 102 ACC'. Site applied, cream coloured (once applied) waterstop. Mix CarboStop 102 resin and CarboStop 102 ACC accelerator in a weight ratio of 20:0.4. Apply and cure as per manufacturer's Application Guide, revision date '19/09/25'. For use with water up to 23°C. This material is for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 319 PVC Cement'. Clear Solvent Cement. Apply as per manufacturer's TDS '319-05-2024'. Cure for 4 hours@5°C. For use with water up to 23°C.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 Bar Maximum operating temperature 65.0°C
Range of bottom entry BS1212-4 (2016) delayed or non delayed action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
Wall hung concealed WC flushing cistern with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Low Level WC suites incorporating a frame mounted ceramic pan that is fitted with a washing & drying arrangement which is fed via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The cistern incorporates a side entry BS1212/4 float operated inlet valve and provides a type `AB` air gap. The drop type flush valve provides a single flush of 6 litres and is operated by elbow push button levers that are designed into the front of the cistern cover. Maximum working pressure 10.0 bar. Cold water use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OASISBM | Chrome | 1/2" BSP (F) | 8 bar | 65 °C | Utopia | Body | No | Solenoid | Not Applicable | Aerator |
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator. The products are supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43084 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T43064 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T43194 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On rear of body | No | |||||
| T44014 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44054 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T44034 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45004 | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | On body | No | |||||
| T45014 | BSP 1/2" (F) | 10 bar | 85 °C | Company logo | On operating member | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TC28 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28, Production date (DD/MM/YYYY) | Body | No | |||||
| TC28-1 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28-1, Production date (DD/MM/YYYY) | Body | No |
Non-verifiable double check valve assembly with DZR brass body, incorporating two spring loaded, resilient trim in-line check valve cartridges. Compression connection to be used with copper pipe BS EN1057 only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C for 12.10102.035.CP5R-8511, Maximum operating temperature 65°C for 12.10112.035.CP5R-8511.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| XDSV12 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL15TA90 (Plastic)Red | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No | |||||
| SL15TA90 (Plastic)Blue | BSP 1/2" (M) | 16 bar | 85 °C | Hent, WRAS | Body | No |
Range of non-rising spindle headworks with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HW28C | 27.8mm | bar | 85 °C | WANHAI, WRAS, HW28C, Production date (DD/MM/YY) | Body | No |
Kisdon range of single hole single outlet (swivel) pull out spray combination tap assembly (chromium plated brass) with ¼ turn ceramic disc headwork and single lever operating members. The outlet of the pull-out spray incorporates a plastic flow aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 818JK | Chrome | 1/2" BSP | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Waterfall | Click Type |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW103006000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | |
| TVW104002000XX | Various | ½” BSP (M) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel) The products were already tested according to the TCS. The report from SKZ is attached.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic disc headwork with various type operating members. The spout outlet incorporates a plastic aerator. Product is supplied with click type pop-up waste – not verified by test. Maximum working pressure 6 Bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| N SNK EF C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
A single-hole single outlet swivel combination tap assembly with brass body (chromium plated). Incorporating ceramic cartridge headwork. The spout outlet incorporate a plastic aerator. Maximum working pressure - 10 bar. Maximum operating temperature - 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, swivel, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Model BLS4ZZX is supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C.
Single hole, double outlet (swivel) combination tap assembly (chrome plated brass body). Incorporating a ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 2TH WMBAS C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BLK | Black | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BB | Brushed Brass | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
Two hole, single outlet (fixed) combination tap assemblies (brass body, chrome finish), incorporating quarter turn ceramic disc headworks and single lever operating members. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc headwork with dome type operating member. Temperature is controlled independently via thermostatic cartridge with single lever operating member. The inlets incorporate a stainless steel strainers and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate It provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M33135 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| M4305 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A, E or F – Dome, cross top or lever types Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F3068-** | Various | BSP 3/4" (M) | 10 bar | 60 °C | LANBIAO | Rear of body | No | Ceramic disk diverter | Metal Backnuts | Aerator | Flow Regulator Fitted, |
1)No Suffix-Chrome 2)-**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F8121KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| F8141KP-** | Various | BSP 3/4" (M) | 10 bar | 85 °C | LANBIAO | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
1）No Suffix-Chrome 2) -**Represents the following different surface treatments: 1.H = Black 2.DYB = Matte white 3.BZ = Perl white painted 4.HGTS = Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 48 130 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 140 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 150 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 160 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 430 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator | ||
| 48 431 xx0 | Various | basic set 10303180 | 10 bar | 60 °C | AXOR | laser etched on the spout | Yes | 1/2 Turn ceramic disk | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish Products need to be installed in combination with basic set 10303180.
Range of three-hole, single outlet, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up or lever type waste – not verified by test. Maximum working pressure. 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B005* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of free-standing sanitary macerating disposal units. The units are fed via a flexible hose assembly. Flow is controlled by a solenoid valve and discharges via a type `AB` air gap (verified by test, suitable of fluid category 5 backflow protection). Maximum working pressure 6.0 Bar Maximum operating temperature 40.0°C
Range of monochloramine generators incorporating UPVC pipework, fittings and an external flow sensor. Maximum working pressure 6.0 bar. Cold water use only.
Range of cylindrical or tubular expansion vessels with epoxy coated carbon steel bodies. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C
Range of filling loop assemblies consisting of an in-line isolation valve, an in-line double check valve assembly (suitable for back flow protection against fluid category 3) that incorporates an isolation valve and a stainless-steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Inline filter with plastic body. Maximum working pressure 5.0 bar. Cold water use only.
Range of stainless-steel(SS304L) press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of green Sappro butt-welded polypropylene fittings for use with Sappro PPR pipes. Maximum working pressure: 20 Bar. Maximum operating temperature: 23°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
F1C compression & F5 press fittings for use with B1 multilayer PEX/AL/PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of DZR brass compression fittings for use with Q-Therm PEX-b Pipes (SDR 7.4) Maximum working pressure:20 bar, cold water use only
EG Range of copper, brass capillary lead free solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression fittings with brass, chrome plated brass bodies. For use with copper pipe (EN 1057) Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of compression fittings with brass, nickel plated brass bodies for use with copper pipe (manufactured to EN 1057). For above ground use only. Max working pressure 16.0 bar. Max operating temperature 85°C.
‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of compression fittings with polypropylene bodies for use with PE100 pipe (manufactured to EN 12201). Some of the female adaptors (55920-9-L, 55920-10-L, 55920-11-L & 55920-11-M), female threaded elbows (56935-10-L, 56935-11-L & 56935-11-M) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 16.0 bar. For above and below ground, cold water use.
"PRESSTITE" range of press fittings with nickel plated brass bodies incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved by a TH crimping profile. For above ground use only. Maximum working pressure 10.0 bar. 20 & 26mm pressfit sizes cold water use only. Threaded and pressfit 16mm size maximum operating temperature 95°C. From June 2025: The 20 & 26mm pressfit sizes maximum operating temperature 95°C.
Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
5000 series of copper end feed fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Dual flush, WC outlet valves for either full or reduced flush. Incorporates an internal overflow. Cold water use only.
Dual flush, WC outlet valve operated via a lever operated assembly for either full or reduced flush. Incorporates an internal overflow. Cold water use only.
Range of dual flush WC outlet valves operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Stainless steel plate heat exchangers with copper brazing.
Near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
Compact wall outlet elbow with brass body (various finishes). Maximum operating temperature 85.0°C Open outlet use only
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.
Range of overhead shower heads and arms incorporating a brass or ABS plastic body. The inlet of models KSAB4K and HEAH06BK incorporates a stainless-steel strainer and plastic flow regulator. Model EKIT01/A is a shower kit consisting of a shower hose, handset and riser rail and model AIR1HSCPWHUK shower handset only. Open outlet use only. Maximum operating temperature 60°C.
Range of Y-patterned strainers with brass bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
GYS20/W Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
In-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 Bar Maximum operating temperature 85.0°C
Range of draining taps, straight or elbowed with brass bodies incorporating a rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 95.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 902001 X XXX | VARIOUS | 1/2” BSP male inlet. | 10.0 bar | 85 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| 902002 X XXX | VARIOUS | 3/4” BSP male inlet. | 10.0 bar | 65 °C | PPI | BODY | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: F – Cross Top Type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| R 1/2 C | Chrome | 1/2" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| R 3/4 C | Chrome | 3/4" BSP Male | 7.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps will be supplied with an optional Flow Regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 15 745 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 15 764 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | hansgrohe | on the escutcheon | Yes | Push button detent | |||
| 36 717 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 727 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent | |||
| 36 773 xx0 | Various | basic set (G3/4) | 10 bar | 70 °C | AXOR | on the escutcheon | Yes | Push button detent |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of wall mounted, or concealed manually operated blending valves, (brass body, chrome finish), incorporating a ceramic cartridge headwork controlling both the flow and temperature with a single lever operating member. Maximum working pressure 5 bar. Maximum operating temperature 85°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Wall mounted thermostatic bar, shower valve, incorporating a ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Each inlet incorporates a combined EPDM washer and stainless-steel strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VE SHXSMFF C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| RP3 CE SHXSMFF C | Chrome (Cr3) | 15mm compression | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T43014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43084T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43034 | Chromed | BSP 3/4" (M) x BSP 1/2" (M) offset unions | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43064B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T43194B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054B | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44014T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| T44054T | Chromed | BSP 3/4" (F) | 10 bar | 85 °C | Company logo | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Range of wall mounted, thermostatic shower valves (brass body – Chrome finish), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted bar type thermostatic shower valves (brass body, chrome finish) incorporating quarter turn ceramic disc headwork which controls the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic blending valves with chrome plated brass bodies and ceramic disc headwork with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge also with a dome type operating member. Inlets incorporate single check valve cartridges however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of float operated inlet valves incorporating with brass bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of non-return, swing gate valve with brass bodies and brass discs. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. VIT-20-PRBZ ½”, ¾” & 1” & 1¼” size have inspection ports on the outlet only. 2” to 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of in-line adjustable pressure reducing valves, with nickel plated DZR brass bodies and stainless-steel strainer. Various models are supplied with a pressure gauge (see model). Compression models are for use with BS EN1057 copper pipe. Maximum working pressure 16.0 Bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of spherical valves with (brass bodies) incorporating a brass ball with PTFE seat. Maximum operating pressure - 25 bar. Maximum operating temperature - 85°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of spherical valves with bronze bodies (brushed chrome plated), brass ball and PTFE seals. Incorporating a lever type operating member. Maximum working pressure 25.0 Bar Maximum operating temperature 85.0°C
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Range of electronically actuated ball valves with brass bodies, chromium plated copper balls, PTFE and silica gel seals. Maximum working pressure 16.0 Bar. Maximum operating temperature 100°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 Bar. Cold water use only
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
2Z126 FGAXXXB16NS01 range of brass gate valves or FGAXXXD16NS42 range of DZR brass body gate valves, with PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (MV40-1138.RS, MV40-1138 & MV40-1138.D models). Bronze body, bronze wedge and lock-shield (MV40-1153.LS & MV40-1138.LS models). Brass body, brass wedge and handwheel (MV40-1120 model only). Maximum working pressure 20.0 bar & 25.0 bar (model MV40-1153.LS only). Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of non-rising spindle gate valves with bronze bodies, incorporating a hand wheel operating member. Maximum working pressure 16.0 Bar Maximum working temperature: 85C
Range of gate valves, (bronze bodies) incorporating either rising or non-rising spindle headworks and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar Maximum operating temperature 85°C.
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, having rate of flow control facility controlled via a pilot system. Spring ratings of pilot valve are 2 to 20 psi / 0.138 to 1.38 bar, 25 to 50 psi / 1.72 to 3.4 bar. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
In-line electrolytic scale reducer with copper bodies for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Range of water conditioners with stainless steel bodies. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
'TENAC-C 4590'. White (translucent) coloured, injection moulded acetal material. For use with water up to 85°C.
'SF-CM1'. Factory applied, grey coloured, sulphate resistant cement mortar. Mix cement mortar, sand & water in a 2:1:0.4 mass ratio and apply as per manufacturer's user instructions 'SF-CM1', 'Vision A1' dated '2024-7'. Cure for 12 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM119-1'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no.: LM-001', 'Edition: A', 'Issue date: 2024-JAN.-15th'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Tecomid NA40 GR25 NL HS QF (white coloured) and Tecomid NG40 GR30 BK250 HS QW, Tecomid NA40 GR30 BK005 HY QH & Tecomid NA40 GR30 BK250 HY QW (black coloured). Injection moulded PA materials. Tecomid NA40 GR25 NL HS QF (white coloured) & Tecomid NG40 GR30 BK250 HS QW (black coloured) are suitable for use with water up to 85°C. Tecomid NA40 GR30 BK005 HY QH (black coloured) & Tecomid NA40 GR30 BK250 HY QW (black coloured) are suitable for use with water up to 23°C.
'Synolite 5410-P-3'. Green coloured polyester resin material manufacture by hand lay-up. For use with water up to 23°C.
'SABIC® PP 48M10'. White coloured, injection moulded polypropylene material. For use with water up to 85°C.
'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.
'GJ-yzxj-V40 EPDM valve seat'. Black coloured, compression moulded EPDM valve seat. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
'EXJ2024'. Black coloured, compression moulded EPDM material. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MGA024BTM | Black | 1/2" BSP (F) | 9 bar | 65 °C | Mediclinics | Body | No | Solenoid | Not Applicable | Aerator |
Concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a Syphon (Phantom S), Pneumatic Drop Valve (Phantom V) or Cable Operated Drop Valve (Phantom T) with full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or push button. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M1005 X XXX | VARIOUS | 3/4” BSP male inlet. | 10 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel or brass bodies, see models). The flow is controlled by a solenoid valve that is activated via an infrared sensor. Temperature is controlled independently via a single lever operating member. The spout outlets incorporate plastic aerators. Supplied with hoses that incorporate stainless steel strainers and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-PS***-**-**** | F1/2, M15*1 | Open outlet use only bar | 85 °C | Kind, WRAS, Production date(MM.YYYY) | Ferrule | No |
Note: 1. 1st *** denotes the hose length: 15-300cm: E.g., 015 = 15cm, 100 = 100cm, 200 = 200cm. 2. 2nd ** denotes the hose size: 06=DN6, 07=DN7 3. 3rd **** denotes the connections, and can be replaced with any of the following: 01=F1/2 05=M15*1
‘TankBoost’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator and a swivel nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D22 | 22 mm | 10 bar | 85 °C | Gear, D22, Production date (DD/MM/YY) | Body | No | |||||
| D15H | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| D15C | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| R19H | 19 mm | 10 bar | 85 °C | Gear, 19H, Production date (DDMMYY) | Body | No | |||||
| R19C | 19 mm | 10 bar | 85 °C | Gear, 19C, Production date (DDMMYY) | Body | No |
Range of single hole, single outlet (swivel) combination taps assemblies (brass bodies - various finishes, see model) incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-down spray outlet with plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The cold inlet includes a loose chrome plated brass adaptor ½” BSP (M) x ½” BSP (F) incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The pull-out spray handset also incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar . Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8202W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8022W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-T8182W | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8022AW | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Aerator | |
| SH-QT8882CW | Chrome | G1/2,female | 10 bar | 60 °C | SHANHU | body | No | Ceramic cartridge | C-plate | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| R BAS C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | C-plate | Flow Straightener | Pop Up |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MA3580-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3580PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator |
Models added December 2025: MA3580PC MA3581PC MA3582PC MA3584PC
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 305B1 | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Aerator | |
| 824B | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Open Outlet |
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), Incorporating a ceramic cartridge headwork with lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating non-rising spindle headworks with dome type or cross top operating members. Both models are supplied with a plastic flow straightener. Capable of achieving AUK3 Tap Gap Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8204 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8184 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SH-T8035 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8066B | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119A-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119A-L25-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 504109 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 5594201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 144201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8060A | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119-L25-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| USH0228 | chrome | 3/4" x 1/2" offset unions | 10 bar | 60 °C | SONAS | on body | No | 1/4 Turn ceramic disk |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L446100MA | Tri-chrome | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100DH | Matt black | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100SA1 | Brushed gold | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT010R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-KT008R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Various finish： (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC BDSM C MT | Chrome | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| RP3 VAC BDSM C MT | Chrome 3 | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B004* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| B009* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Rosette | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
*denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HGLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS38 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, |
Free standing, upright floor mounted inlet legs (chromium plated brass), incorporating stainless-steel braided PEX lined flexible hose assemblies. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
‘LSMRI’ range of copper-nickel press fittings (‘M’ type crimp profile) for use with copper-nickel ‘LSMRI’ pipe. Above ground use only. Maximum working pressures: Press fittings: 16.0 bar, LSMRI-PN6 Series flange: 6.0 bar, LSMRI-PN10/16 Series flange: 10/16 bar. Maximum operating temperature 99°C.
Multipipe range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘HLBRxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The HLBRTC‐1 tank connector, HLBRSS‐1 and HLBRBS‐1 tap connectors all incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘3600xx’ range of brass compression fittings for use with copper pipe (manufactured to EN 1057). The 360014 tank connector, 360013 and 360017 tap connectors all incorporate an EPDM washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘CFxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
‘F17’ range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
'PlumbRight' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure 12.5 bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
“D-“ and “E-“ range of 304 and 316L stainless steel press fittings, in either ‘M’ press profile (D- prefix models) or ‘V’ press profile (E- prefix models) for use with stainless steel pipe (316L & 304 manufactured to EN10312). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature: 85°C.
Range of pre-assembled hydraulic blocks incorporating plate heat exchangers, pressure relief valves set at 3.0 bar, circulation pumps and flow regulators. Maximum working pressure: Primary 2.5bar & secondary 10 bar. Maximum operating temperature 80°C (CH) & 60°C (DHW).
Range of in-line water meters incorporating bronze copper alloy bodies and EPDM O rings. Maximum working pressure 10.0 Bar Maximum operating temperature 30.0°C
Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Maximum operating temperature 60°C. Open outlet use only.
Range of wall or ceiling mounted shower arms with stainless steel bodies (various finishes - see model). Maximum operating temperature 60°C.
Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FH SLRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 BB | Brushed Brass | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 GM | Gun Metal | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| 225788 | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| RP3 FH SLRD01 C | chrome 3 | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 G | Gold | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, |
Two Fixed Head's with different finish and size as below FH SLRD01 C / BB / GM - (Dia 200mm) FH SLRD02 C - (Dia 250mm) FH SLRD03 C - (Dia 300mm) 225788 - (Wickes selling code for FH SLRD03 C) RP3 FH SLRD01 C - (Dia 200mm, chrome 3) FH TDRD01 C - (Dia 157mm) FH TDRD01 C / G - (Dia 200mm) FH TDRD03 C - (Dia 300mm)
In-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 Bar Maximum operating temperature 85.0°C
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SD2001 | 1/2" BSP (M) | 16 bar | 85 °C | SD and size | Body | No | |||||
| SD2001 | 3/4" BSP (M) | 16 bar | 85 °C | SD and size | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 936L | Chrome | G3/4, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 932L | Chrome | G1/2, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 530 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | 1/4 Turn ceramic disk | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| RS2 3/4 C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| 225916 | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
‘KM1001 series’ of stainless steel braided EPDM lined flexible hose assemblies. Compression end connections are for use with copper pipes (manufactured to EN 1057). Compression end connections are also available with brass bodied (nickel plated) isolation valves incorporating a chrome plated brass ball. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature: 60°C.
Range of EPDM braided hoses (various options) and optional end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of flexible corrugated stainless-steel tubing with white plastic covering. Compression connections are for use with copper pipe (manufactured to EN 1057). Captive nut end connections incorporate an EPDM gasket. 2BACa0504 prefix models incorporate a servicing valve (chromium plated brass body with brass ball) on the compression end connection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 16 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Series of wall mounted, thermostatic mixer valve with brass bodies, diverter headwork that controls flow between one, two or three outlets (see model) with various type of operating member. The temperature is controlled independently via a thermostatic cartridge operating member with a manual override button. Inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 55°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814109 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, | ||
| 814111 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, |
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. The valves incorporate a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | GEAR, Model no. and Prodcution date (DD/MM/YY) | Body | No | |||||
| D35 | 35mm | 10 bar | 85 °C | GEAR, Model no | Body | No |
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs, PTFE stem gaskets and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated). The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, spherical valve and DZR pilot valve, DZR electrically actuated spherical valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 2.0 bar – 12.5 bar. Maximum operating temperature 80°C.
Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of spherical valves with nickel plated brass bodies, brass ball and PTFE seats. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electrically operated motorised spherical valves incorporating brass bodies and stainless-steel balls. Maximum working pressure 20.0 bar. Maximum operating temperature: 85°C.
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets and Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating bronze bodies and discs with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure; 20 Bar Maximum operating temperature; 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 10.0 Bar or 16.0 Bar Maximum operating temperature 40.0°C
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, brass wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
'PENTANOL DI 8055 BLACK'. Factory applied, black coloured Bitumen based coating. Apply as per manufacturer's TDS 'January HD 2024'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Corro Coat EP-F1003HW Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's Technical Data Sheet dated '31 July 2018'. Cure for 4 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.1 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver 1 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless RF35 (2024) Coating System’. Site applied, grey coloured (once applied), two-part epoxy coating. The primer comprises of ‘Corroless EPF (2022) Primer Base Red’ and ‘Corroless EPF (2022) Buff Temperate Hardener’, to be mixed in a 1:1 volume ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 24 hours at 10°C. The coating comprises of ‘Corroless RF35 (2024) Base 00-A-01 Portland’ and ‘Corroless RF35 (2024) Hardener’, to be mixed in 5.5:1 weight ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 7 days at 10°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'BX-455'. White coloured (opaque) Silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
Grilamid LV-30H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA natural. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural & Grilamid LV-65H FWA black 9225 were added to the approval in March 2026. Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. For use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'Revolve M-748 Black'. Black coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR, P-1700 NT 11, GF-121 NT ECHO RP & P-3500 NT LCD ECHO RP’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937, GF-121 BK 937, GF-121 BK 937 ECHO RP, GF-120 BK 937 ECHO RP & P-1700 BK937 ECHO RP’ (all black coloured). ‘Udel P-1700 WH 7407’ (white coloured). Injection moulded, polysulphone materials. For use with water up to 85°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Dutral K-Co-054'. Black coloured, compression moulded EPDM materials. Shore hardness between 52A & 80A. Tested in-radius size 1.0mm. For use with water up to 65°C.
Range of injection moulded, VMQ rubber gaskets, seals, & `O` rings manufactured from the below compounds. The components are available in blue, green, grey, opaque (beige coloured), red, transparent & yellow. The numbers in the name of the compound indicates the shore hardness between 40 & 80. Tested in-radii sizes: Gaskets: 0.2mm - 5.0mm. Seals & `O` rings: 0.5mm - 5.0mm. S50B04E, S60B00E, S70B06E, S70B07E, S70V02E, S50V01E, S60O02E, S70O05E, S50O03E, S50O05E, S60O01E, S70O03E, S40A01E, S60A00E, S70A02E, S40R03E, S45R01E, S50R10E, S50R01E, S60R05E, S65R04E, S70R04E, S80R01E, S40R02E, S50R06E, S60R07E, S70R19E, S70R24E, S50T05E, S50T00E, S55T00E, S60T00E, S60T00T, S70T04E, S70T00E, S75T00E, S80T00E, & S70G01E. For use with water up to 85°C.
72401, 72501, 73401, 73501, 74401, 74501, 75401, 75501, 76401, 76501, 77401, 77501, 78401, 78501, 79401 & 79501. Range of press moulded, solid silicone rubber materials which are blue or red coloured. Shore hardness between 20 & 90. Tested in-radius size 1.0mm. for use with water up to 85°C.
'Hytrel® 4068FGDW'. Cream coloured, injection moulded, thermoplastic polyester elastomeric material. For use with water up to 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 4203801-1 | chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, |
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT103002000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT104001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT125001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT105501110XX | See Below | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | Lever | No | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Range of spherical valves with DZR brass bodies, chromium plated brass balls, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Compression connection to be used with copper EN1057. AI-0396A062815CR incorporates an approved single check valve cartridge, verified by test - suitable for backflow protection against fluid category 2. Maximum working pressure: 25.0 bar. Maximum operating temperature: 100°C (model AI-0396A062815CR 65°).
Range of shower hoses. The H-38033 model has a PVC inner liner and stainless steel interlocked outer casing. The H-38034 and H-38035 models are multi-layer shower hoses with a PVC inner liner. Maximum operating temperature 60°C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814110 | chrome | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, | ||
| 814112 | 814112 | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, |
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum operating pressure 10.0 bar. Maximum operating temperatures: 430357-003, 430357-004 and 430357-006 models: 85°C, 430357-008, 430357-010, 430357-011 and 430357-012 models: 65°C.
Non-verifiable single check valve assembly with a stainless-steel body. Maximum working pressure 10.0 bar. Maximum operating temperature of 85°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘TankBoost 5 bar’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks and cross top operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste (not verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Non rising spindle headwork incorporating a brass body and NBR seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headwork assemblies with brass bodies, NBR ‘O’-rings and silicone gaskets. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with EPDM seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar, Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| D39 | 39mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 501102 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 501101 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591103 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141102 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator |
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies, chrome finish(chromium plated brass), with a non-rising spindle and cross-top operating member(models 49944 & 88081) or ceramic disc headwork with lever type operating members(model 26251). The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L449200DH | Matt black | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200MA | Tri-chrome | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200SA1 | Brushed gold | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 141701 | chrome | 1/2" BSP | 10 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 503109 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 5593201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 143201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, |
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Models 91742, 805777 & 21775 incorporate a non-rising spindle headwork. Models 91742 & 805777 with dome type operating members Model 21775 with lever type operating members. Models 77174 & 805783 incorporate a quarter turn ceramic disc headwork with dome operating members. The fitting incorporates a manual diverter to the shower outlet The spout outlet incorporates a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| J THBSMVO C | Chrome | G 3/4" (M) | 10 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K005* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| K008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 20.189.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| 20.193.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
Where xxx denotes finish, can be replaced by: 002 – Chrome DC2 – Supersteel DA2 – Warm sunset AL2 – Brushed hard graphite A02 – hard graphit DL2 – brushed warm sunset GN2 – brushed cool sunrise A02 – hard graphite MS2 – satin steel GL2 – cool sunrise MS2 – satin graphite
Range of chemical dosing equipment which incorporate self-closing valves and plastic bodies. The outlet of the injector incorporates a connection for injection of chemicals via venturi action and the inlets include stainless-steel strainers. Maximum operating pressure 9 bar. Maximum operating temperature 70°C.
Range of Socket weld, Click weld, Butt weld and Electro fusion fittings (see models), for use with ABN//INSTAL CT Faser RD Series 3.2 / SDR 7.4 & ABN//INSTAL CT Faser RD Series 5 / SDR 11 pipe. Maximum working pressure; (see models) Maximum operating temperature; (see models)
Range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *‐KJ600304 and *-KJ600316 stainless steel pipes. The "KJ6278" prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Uponor S-Press press fittings, Uni-X & Uni-C compression fittings for use with Uponor MLC pipe. Maximum working pressure 10.0 bar, maximum operating temperature 70°C.
Range of brass compression fittings for use with copper pipes (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flange fittings with TP2 copper bodies, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘M’ profile copper press fittings with EPDM ‘O’-rings for use with copper pipes (manufactured to EN 1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
'Flomasta’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of end feed copper fittings for use with copper pipes (manufactured to EN 1057). The 5043G series and 5002G series models incorporate an EPDM ‘O’-ring on the captive nut connection. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Dual flush, WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of dual flush, WC outlet valves. Each valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of ultrasonic dry type water meters with brass bodies. Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C.
Range of brass bodied threaded fittings and a brass end feed fitting (C04069H00081A model only). The CL08069H192B4 model is chrome plated. The C04069H00081A model end feed fitting is for use with copper pipe (manufactured to EN 1057). The C04149H00191A model incorporates a plastic flow straightener. Maximum working pressure 10.0 bar, except for the C04149H00190A and C04149H00191A models which are open outlet use only. Maximum operating temperature 85°C.
Threaded adaptor (brass body) soldered with copper pipe and a range of thread extensions (chrome plated brass bodies). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of threaded fittings with either brass or chrome plated brass bodies. Maximum working pressure 40 Bar Maximum operating temperature 85°C.
CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WH51-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH03** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-WH05** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA61** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA60** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA55** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA54** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No |
The suffixes of ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.477.xxx | Various | G 1/2" | Open Outlet bar | 65 °C | Grohe | Shower faceplate | No | Fixed Head, |
Where xxx denotes finish, can be replaced by: 000 – Chrome DC0 – Supersteel DA0 – Warm sunset LS0 – moon white AL0 – Brushed hard graphite DL0 – brushed warm sunset GN0 – brushed cool sunrise GL0 – cool sunrise MG0 – satin graphite MS0 – satin steel A00 – hard graphite BE0 – polished nickel EN0 – brushed nickel
Range of shower handsets with ABS bodies (various finishes, see model). The spray outlet is either multifunction or single function depending on series. Open outlet use only. Maximum operating temperature 60°C.
Range of wall mounted or ceiling mounted shower arms with brass bodies (various finishes - see model). Maximum operating temperature 65°C.
Stainless-steel, angled, wall mounted overhead shower, incorporating silicone nozzles. Maximum operating temperature 85°C.
Range of In-line Y patterned strainers with ductle iron bodies (blue epoxy powder coated) and stainless-steel mesh. Maximum working pressure: 16 Bar Maximum operating temperature: 85 °C
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FBA015 | Bronze | 1/2" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable | |
| FBA020 | Bronze | 3/4" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable |
Range of drain taps with a brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 HNK FL5 C CD | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| TAP1103 | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M3401 X XXX | VARIOUS | 1/2” BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/2 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Flow Regulator Fitted, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of pillar taps (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with single lever operating members and flow regulator in the inlet (1/2” only). The spout outlets incorporate a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure: 10.0 Bar Maximum operating temperature: 85°C
Range of shower hoses, multi-layered hose (various external finishes) with PVC inner liner, brass end connections. Open outlet use only. Maximum operating temperature 60°C.
Range of Stainless-Steel braided EPDM lined flexible hose assemblies with various end connections. For use with copper pipe manufactured to EN1057 Maximum working pressure; 16 Bar Maximum operating temperature; 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate push-fit isolation valves. Compression connection to be used with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. Maximum working pressure and maximum operating temperature 12 bar @cold water use only & 7 bar @ 65°C.
‘DG10E PF series’ of stainless steel braided EPDM lined flexible hose assemblies with EPDM ‘O’-rings or gaskets available with a variety of end connections. The DN10 bore 15mm push fit connection is also available with a screwdriver operated isolation valve. Push-fit connections are for use with copper pipes (manufactured to EN 1057) and PEX pipes (manufactured to BS 7291-3). Maximum working pressure 10.0 bar. Cold water use only.
‘FS4E Series’ 2 port, 3 port and 4 port nickel plated brass manifolds incorporating stop valves. The models include white operating members with either red, green or blue indices. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of automatic air release valves with blue epoxy coated cast iron bodies and plastic floats. Maximum working pressure 10.0 Bar 16.0 Bar, 25.0 Bar (see models) Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQDL1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 938HP | Chrome | 15mm Compression | 5 bar | 70 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 958HP | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic shower valves, (brass bodies - various finishes), incorporating a thermostatic cartridge controlling the temperature. Supplied with either single lever or cross top operating members depending on model and with a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Range of thermostatic mixing valves with between 1 and 2 outlets. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Models Mira Activate 1.1903.090, 1.1903.091, 1.1903.092 & 1.1903.093 incoporate a built-in pump. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves have a maximum working pressure of 1.0 bar. Maximum operating temperature 45°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQ75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, | |
| TS75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, |
AQ75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 704418 (shower handset) • ACY1008 (shower hose) TS75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 707540 (shower handset) • ACY1008 (shower hose)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV1 | Chrome | 5 bar | 65 °C | Aqualisa | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, |
AQRNDCV1 Packed Products. Waterway contents are: 705342 (shower valve) 704418 (shower handset) ACY1008 (shower hose) ACY1013 (wall outlet)
Range of thermostatic shower valves with a quarter turn ceramic disc headwork or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar Maximum operating temperature 65°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, with stainless steel (CF8 or CF8M) discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
‘GNVP’ range of non-return valves with a white plastic housing. The product incorporates two test/drainage plugs. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of in-line pressure reducing valves with either chromium plated DZR brass bodies, with manually adjustable outlet pressure ranges between 2.8bar to 3.2bar. Compression connections to be used with copper pipe EN1057 only. Maximum working inlet pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of pilot operated pressure reducing control valves (ranges of 0.7 to 7.0 bar or 1.5 to 15.0 bar) with ductile iron bodies (blue epoxy coating). Maximum working pressure: 16 Bar. Cold water use only.
Solenoid valve with a brass body, EPDM diaphragm and ‘O’-rings. Maximum operating pressure 10.0 bar. Cold water use only.
Range of spherical valves nickel plated brass body with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
In-line spherical valve incorporating a chrome plated brass body and ball. Compression end to be used with copper pipe EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of spherical valves with various means of operation some via handle some with actuators, see models, comprising of a bronze valve body, spindle and ball valve, and EPDM O rings Maximum working pressure 16 bar Maximum operating temperature 90˚C.
Spherical valves incorporating a brass bodies and ball, PTFE seat, EPDM and NBR ‘O’-rings. The valve 8 718 657 822 incorporates a branch which is intended to connect to the primary circuit of a combination boiler. Maximum working pressure 10.0 Bar. Cold water use only.
Range of angled (S0273 and S0274 suffix models only) or in-line spherical valves with a nickel plated brass body, chromium plated brass ball and PTFE or EPDM seats. The products are either screwdriver operated or supplied with a T-handle (S0233BH-1 and S0233BH-2 models only). Compression ends are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass balls (chrome plated) and EPDM ‘O’-rings. For use with copper pipe to (EN1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C.
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever, lockable lever or tee handles. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Push fit in-line spherical valve with plastic body, for use with PE-X pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe (manufactured to BS EN1057). Maximum working pressure/temperature: 12.0 Bar (cold water) and 7.0 Bar at 65°C.
Range of gate valves with a non-rising spindle and a handwheel operating member. DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM wedge and a non-rising spindle. Maximum working pressure 16.0. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, for use with copper pipe (manufactured to EN1057). Incorporating a either a handwheel or lockshield operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
‘Series 116’ range of balancing valves (DZR Brass body). Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaGrout-800'. Site applied, grey coloured Cementitious grout. Mix grout and water in an 8:1 weight ratio and apply as manufacturer's IFU 'Issue No.: 1', issued 'July 2024'. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versilon™ C-544-A I.B'. Triple layered, extruded tube consisting of a transparent (clear) polyurethane inner layer, white coloured polyester middle layer & transparent (clear) polyurethane outer layer. For use with water up to 65°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
'B1-4773' Lip Seals and 'O' rings. Black coloured, EPDM components with shore hardness of 70. Compression moulded Lip Seals have an in-radius size of 2.7mm. Compression moulded ‘O’ rings have an in-radius size of 1.5mm. Injection moulded ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'VEV1'. Black coloured, compression moulded FKM seal. Shore hardness 70 A. Tested in-radius size 4.45mm. For use with water up to 23°C.
'FKM 70 514404'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
'Weld-On 719 Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '719-05-2024'. Cure for 8 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 795 Blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's data sheet '795-05-2024'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 705 ECO Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '705 ECO-09-2024'. Cure for 12 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use only
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 58 130 xx0 | Various | G 1/2" | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 42 540 xx0 | Various | G 1/2" | open outlet bar | 65 °C | AXOR | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 119 xx0 | Various | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 131 xx0 | VArious | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 152 180 | NA | G 1/2" | open outlet bar | 65 °C | hansgrohe | sticker only, marking will be on the finish set | Yes | Not applicable | Not Applicable | Open Outlet |
model 58131xx0 and 58119xx0 are identical in the water pathway, only difference is the cover plate design. model 58130xx0 and 42540xx0 are both composed of the finish set 58131xx0/58119xx0 and basic set 58152180, only difference is the marking on the faceplate 58130xx0= hansgrohe, 42540xx0= AXOR
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH001* | Various | ½” BSP (F) conical nut x ½” BSP(F) conical nut | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable | |
| SH002* | Various | ½” BSP (F) conical nut x M15x1 | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable |
1) The products are interlock type 2) * denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L325604DH | Matt black | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| 1L325604MA | Tri-chrome | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| 1L325604SA1 | Brushed gold | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV2 | Chrome | 5 bar | 80 °C | AQUALISA | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, |
AQRNDCV2 Packed Products. Waterway contents are: SDCV.002 (Valve) 704418 (handset) ACY1008(hose) ACY1013(wall outlet) ACY1002(fixed arm) 704426(top shower)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 35H-5 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35H-F | 35mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35P-1 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35PH-1 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40D-5 | 40mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40D-F | 40mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40H-5 | 40mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40H-F | 40mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of near boiling water dispensers comprising of an install rail, under-counter boiler unit with a stainless steel tank and a countertop outlet (font). The install rail incorporates a water block, a double check valve assembly (suitable for backflow protection against fluid category 3) with an integral lever operated isolation valve and an adjustable pressure reducing valve (outlet pressure range 3.0 to 3.5 bar). The flow is controlled via a solenoid valve which is activated by a touch method at the outlet. The commercial model outlets (fonts) incorporate a safety button. The solenoid valve incorporates a plastic flow regulator. The countertop outlet (font) incorporates a plastic aerator. All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Maximum supply pressure to the install rail 16.0 bar. Maximum operating temperature 98°C. Cold supply only.
Quarter turn ceramic disc headwork incorporating a brass body, EPDM and NBR ‘O’-rings and a silicone gasket. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 122 100 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 122 101 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 579 600 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 333 001 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 700 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 702 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable |
30 122 100 - Diameter= 25,4mm 30 122 101 - Diameter= 25,4mm 30 333 001 - Diameter= 25,4mm 30 746 700 - Diameter= 25,4mm 30 746 702 - Diameter= 25,4mm 30 579 600 - Diameter= 25,4mm
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M28DF-2 | 28mm | 5 bar | 85 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk |
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies -various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator, (except for the MYKCOR002 & BLKCOR002 models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| KM FRZ BAS3.5 C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Operating member | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 550 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 551 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 557 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 558 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 559 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 560 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 561 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 580 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 584 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 585 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 589 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | ||
| 71 593 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 594 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 598 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | ||
| 71 526 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 527 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 528 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 529 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator |
Where xx0 denotes the surface finish. It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 003 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | ||
| 10 001 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 007 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 102 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 103 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 247031 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247032 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247033 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Lever or Dome type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 526402 | Chrome (CHR) | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526407 | ANT/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526415 | BLA/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526408 | SGW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526981 | VGR/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526980 | SOW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator |
All surface finishes are not in contact with drinking water. The product structure (schedule of materials) of all versions are identical. Surface finish / color explanation: CHR - Chrome ANT - Anthracite BLA - Black Matt SGW - Silgranite White VGR - Volcano Grey SOW - Soft White
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 554 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | Pop Up | ||
| 71 564 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | Pop Up | ||
| 71 870 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 871 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 857 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 878 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K003* | Various | ½" BSP (F) | 10 bar | 65 °C | WINSDRUM | On wall plate | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| K004* | Various | ½" BSP (F) | 10 bar | 65 °C | WINSDRUM | On water outlet | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The MYKCOR003 model incorporates an open outlet spout, all other models incorporate a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SJS-WB100* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| SJS-WB200* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| SJS-WB101* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WB743* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator, (except for the MYKCOR004(& BLKCOR004??? models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 PSNK C CD | Crome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
Note - Both Products are the same, one is wall mounted, one is deck mounted.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720065 | Chromed | BSP 1/2" (M) | 10 bar | 85 °C | MVI | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| 2720095 | Chromed | BSP 1/2" (M) | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TRLS01 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| TRLS10 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS06 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS07 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
Finishes available: Brass, Chrome, Nickel, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Dark Nickel, Vintage Brass, Gold, Matte Gold.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-792* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle, spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-742-2* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-702* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-704* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-L201** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| JD-200** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| SJS-L202** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-SP501 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Spout | No | Not applicable | Aerator | ||
| SJS-SP205 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Decorative plate | No | Not applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Numepress' stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of copper press fittings with EPDM seals for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Fastwarm range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range RP of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘Fastwarm’ range of U profile press fittings (nickel plated brass bodies) for use with ‘Fastwarm’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper capillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
Range of plastic and DZR brass pushfit fittings for use with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipes (manufactured to EN 1057). Maximum working pressure 10.0 bar, except tank connectors which are open outlet use only. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except tank connectors.
'Flomasta' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Range of end feed copper fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of DZR brass metering stations supplied with red and blue test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.409.000 | chrome | G 1/2" | Open Outlet bar | 65 °C | Grohe | Faceplate | No |
‘Union Range’ of wall mounted shower arms (brass bodies) and overhead showers (plastic bodies) both with various finishes (see models). Maximum operating temperature 85°C.
Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 51OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52CS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52DS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6301-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6302-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6303-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 63OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6300-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OS-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OH-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator |
** Representative all models are available with the following finish code: CP-Polished Chrome BN-Brushed Nickel MB-Matte Black ORB-Oil Rubber Bronze PB-Polished Brass WP-Weathered Pewter BB-Brushed Brass
Range of Y-pattern strainers with DZR brass bodies and stainless steel strainers. The compression connection is for use with copper pipe to BS EN1057. Maximum working pressure 20 bar (BSP threaded models ½”-2”), 16.0 bar (compression models). Maximum operating temperature 85°C.
Range of `Y`-patterned strainers with either brass or DZR brass bodies, incorporating a stainless-steel mesh strainer. Maximum working pressure: 25.0 Bar (Models 36233, 36234, 36235, 36236, 36237 & 36238 ) or 16.0 Bar (Models 36230 & 36231 ) Maximum operating temperature 95°C. Strainers with compression connections are to be used with copper pipe manufacture to BS EN 1057. Strainers with M profile press-fit connections are to be used with copper pipe manufactured to BS EN 1057 & SS304 Stainless steel pipe manufactured to EN 10312.
Range of in-line Y patterned strainers with bronze bodies and a stainless steel mesh strainer. Maximum working pressure 20 bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20205.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20255.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20275.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20365.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No |
Range of air venting valves with blue epoxy coated ductile iron or plastic bodies with plastic floats. Maximum working pressure 16.0 Bar. Cold water use only.
Range of automatic air release valves with blue epoxy coated stainless steel bodies and plastic or stainless-steel floats. Maximum working pressure 16.0, 25.0 or 40.0 bar (See Models below). Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 681 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 1/2 (offset) | 10 bar | 70 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | Not Applicable |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| * M980116 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 803250 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Body & Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 801528 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 803251 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 801524 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 801525 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 800204 X XXX | VARIOUS | 15mm compression | 10.0 bar | 60 °C | PPI | Body | No | Single sequential | Metal Backnuts | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 804203 X XXX | VARIOUS | 15mm compression | 10.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 801508 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 801509 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 801510 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
The “*” is for a different Overhead Shower, Shower Hose or Shower Handset, which represent the letters A to Z X XXX Denotes the following: First X: Different handle The second, third & fourth XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Wall Mounted shower valve with shower hand-set, hose with riser rail and overhead shower, available in various finishes. A05846 incorporates a single sequential headwork, all other models incorporate 1/4 turn ceramic disc headwork. Some model include a flow regulator. Models A5846 & A05847 maximum pressure 10.0 bar. All other models maximum pressure 5.0 bar Maximum temperature all models 65°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and stainless-steel discs incorporating EPDM rubber seats. (DN40 - DN200) incorporate a lever type operating member and (DN250 – DN500) incorporates a hand wheel type operating member. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of adjustable, bronze in-line pressure reducing valves. Models 131201015, 131201020 & 131201025 and model 131201032 have inspection ports on the outlet only. Models 131201050 & 131201100 sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of normally closed (L182 models) solenoid valves with brass bodies. Maximum working pressure 16.0 bar: 12900 Maximum working pressure 12.0 bar: 12903 & 12906 Maximum working pressure 10.0 bar: 12909 ,12912 & 12915 Maximum operating temperature 85.0°C
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of electrically (A20 & A150 series) or battery (E20 & E22 series) operated motorised spherical valves incorporating brass or stainless-steel bodies, stainless steel balls and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever, lockable lever or tee handles. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of electrically or battery operated motorised spherical valves incorporating brass, DZR brass or stainless-steel bodies, stainless steel balls and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of plastic bodied inline, tee and angled spherical or servicing valves with EPDM ‘O’-rings. The products are either lever or screwdriver operated (see model). The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except AVT67665SM, AVT67661SM and AVT67445SM.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. Brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies. Maximum working pressure 17.24 Bar Maximum operating temperature 99.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. Non-rising spindle, with a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
'M90-44'. Red coloured, injection moulded POM material. For use with water up to 85°C.
'CY4000'. Black coloured, machined, Phenolic resin impregnated Carbon ring. For use with water up to 85°C.
'GM2025-01'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Abcite® 1060 DW Blue & Abcite® X60 DW Blue'. Factory applied, blue coloured thermoplastic powder coatings applied by dipping in a fluidised bed. Pre-heat substrate the coating is to be applied to for 12 minutes@280°C and apply as per manufacturer’s Application Guide ‘Version 04.05.2015’ (Abcite® 1060 DW Blue) or Technical Data Sheet ‘11/2023’ (Abcite® X60 DW Blue). Post-heat for 5 minutes@160°C. For use with water up to 23°C. These materials are only approved for the pre-heat and post-heat conditions that appear on the approval. If the pre-heat and/or post-heat conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MC-PROOF 4200 AE'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS dated 07.10.2025. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MC-PROOF 4210 AE'. Site applied, grey coloured (once mixed), two-component polyol and prepolymer based coating. Mix Part A (grey liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS '07.10.2025'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novus N49 Graftec'. NBR/fibre material which is dark grey on one side and black on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 Version: 0, 19/11/2020’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquaterra Faser Composite Stabil Pipe PP-R (SDR 6 & SDR 7.4)'. Extruded, multi-layered PP-R pipes comprising of a green coloured inner layer, red coloured middle layer and green coloured outer layer. For use with water up to 85°C.
'Aquaterra Faser Composite Stabil PPR-CT pipe (SDR6, SDR 7.4 & SDR 9)'. Extruded multi-layered pipe comprising of a green coloured PPR-CT inner layer, red coloured PPR/GF middle layer and green coloured PPP-CT outer layer. For use with water up to 85°C.
'PTFE Thread Seal Tape 201 (white), 202 (pink), 203 (yellow), 204 (blue) & 205 (grey)'. PTFE tapes, manufactured by extrusion, stretching and calendaring, available in a range of colours. For use with water up to 85°C.
‘662016, 662014, 662062/SF (251VM), 662062-10PK/SF (523VM), 662061-10PK/SF (113VM)’. White coloured, PTFE tapes manufactured by calendering. For use with water up to 85°C.
‘AH Codes: 662016CB & 662014CB, CB Codes: 571983 & 571984’. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'SPIT EPCON C8+ XTREM'. Site applied, brick coloured (once mixed), chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Expoband H45'. Grey coloured, extruded, flexible FPO expansion joint membrane. For use with water up to 60°C.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8089D-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T8089-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T80810-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T80810D-** | Various | 15mm compression union | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk |
-**Represents the following different surface treatments: 1.PB-ARTISAN BRASS 2.EB-Matte black 3.CP-CHROME
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-AT2** | Various | BSP 1/2" (F) x BSP 3/4" (F) | 10 bar | 60 °C | Kind | Body | No | 1/2 Turn ceramic disk | Not Applicable | Not Applicable | |
| JD-AT3** | Various | BSP 1/2" (F) x BSP 3/4" (F) | 10 bar | 60 °C | Kind | Body | No | 1/2 Turn ceramic disk | Not Applicable | Not Applicable |
Note: ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. The products incorporate a drain port between the cartridges. Compression connection for use with copper pipe to BS EN1057 Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
DAB range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (brass bodies – various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of quarter turn ceramic disc headworks incorporating brass bodies (HW-12, HW -34, HW - 38) or plastic body (HP-12). Maximum working pressure 12 Bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating plastic bodies and stainless-steel filters. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Single hole, single outlet (swivel) pull down spray combination tap assembly (chromium plated brass body) with a ceramic cartridge headwork and single lever operating member. The product incorporates a pull-down spray with a plastic aerator, which also incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 681104 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 681101 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 691104 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 691101 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 891105-1 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator |
Range of single hole, single outlet fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates an plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 052 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 051 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 053 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 054 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 055 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 32002 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41802 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41802L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 81202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81202L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81402 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81402L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 91202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate |
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic combination aerator (63868-00X, 63868-01X) and 2 separate plastic aerators for the hot & cold outlet or filtered outlet (63869-00X, 63869-01X). Maximum working pressure: 5.0 bar Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT053 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT014 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT015 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT004 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | Non-rising spindle | C-plate | Aerator | |
| SL-KT40602R | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT032 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Side of body | No | Ceramic cartridge | C-plate | Aerator | |
| SL-KT054 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT30602W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT40202L | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Flow Straightener |
Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720032 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720034 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720068 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 519413 - MILI RH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 517742 - MIDA RH HP CHR | Chrome | 3/8" | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 528156 - MIDA ECO RH HP BL | Black matt | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| 519414 - MILA RH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526657 - MILA RH HP BL | Black matt | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 528154 - MILA ECO EH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| 528155 - MILA ECO EH HP BL | Black | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WK794* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK795* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK1034* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK305* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB792* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
* stands for the different handle A, B,C and D ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K006* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| B006* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| B007* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| K012* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| K013* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On body | No | Ceramic cartridge | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT40602W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company LOGO | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| SL-KT40502W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company LOGO | Rear of body | No | Non-rising spindle | C-plate | Flow Straightener |
Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SJS-WB102* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| SJS-WB202* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB742* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-2* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Ramge of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (stainless steel body – various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The products are supplied with nylon braided, PEX lined flexible interconnecting hoses and the spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, chrome and black finish - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes brass bodies), incorporating quarter turn ceramic disc headworks. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a quarter turn ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-ATS413* ** | Various | ¾” x ½” BSP (M) offset unions | 10 bar | 60 °C | Kind | Handle | No | 1/2 Turn ceramic disc | Not Applicable | Aerator | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes brass bodies), incorporating quarter turn ceramic disc headworks with a manual diverter to spout outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WB743-2* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WB743-4* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WS792* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 36 107 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator | ||
| 36 115 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K007* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
| B008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of wall mounted, stainless steel spout outlets (various finishes) incorporating a plastic aerator. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TS231** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator | |
| TS232** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
‘EPS50’ range of stainless-steel axial compensators with threaded end connections and ‘EPSF-10’ range of stainless-steel expansion joints with rotatable flanged end connections. Maximum working pressure: 16bar. Maximum operating temperature: 100°C.
Range of ceramic filter cartridges with a plastic body. Cold water and open outlet use only.
Range of ‘PPS/GF BFS (black)’ shrink back fittings for use with ‘Uponor Combi pipe’ (PEX/EVOH/PEX). Maximum operating pressures 12 bar & 6 bar, with maximum operating temperatures 20°C & 95°C respectively.
'Instantor’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Instantor’ stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of DZR brass compression fittings for use with 'Wavin PE-RT Pipe'. Maximum working pressure:20 bar Maximum working temperature:23°c
Range of polypropylene push-fit fittings. The 20, 25 and 32mm sizes are for use with MDPE Pipe (manufactured to BS EN 12201-2). The 15, 22 and 28mm connections are for use with the following pipes: PEX (manufactured to BS 7291-3) for 15, 22 and 28mm sizes. PB (manufactured to BS 7291-2) and Copper (manufactured to BS EN 1057) for 15 and 22mm sizes only. Maximum working pressures: UG601B model: 16.0 bar. All other models: 12.5 bar. Cold water use only.
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
“>B<Press NZ” range of press fittings incorporating copper (EN12165 CW024A) or copper alloy (CC499K-DW) bodies. For use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 16.0 bar @ 30°C and 10.0 bar @ 95°C.
Range of water meter measuring capsules with brass bodies. Maximum working pressure 16.0 bar. Please refer to model for maximum operating temperature.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
Range of electromagnetic flow meters with stainless steel bodies, EPDM inner liner and SUS316L electrodes. Maximum working pressure 16 Bar. Maximum operating temperature 40°C.
‘Hansen True Fit’ range of black coloured, plastic threaded fittings. Maximum working pressure 1/8” – 2” BSP: 16.0bar, 2½” BSP: 12.0bar, 3” – 4”: 10.0bar. Cold water and above ground use only.
Range of stainless steel bodied mechanical pump shaft seals. Cold water use only.
Range of DZR brass metering stations supplied with red and blue test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
Range of shower handsets with chromium plated plastic bodies. Maximum operating temperature 65.0°C Open outlet use only
Range of wall or ceiling mounted shower arms with brass bodies (various finishes). Maximum operating temperature 65°C. Open outlet use only.
Range of shower handsets with brass body available in various finishes. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.569.000 | Chrome | 1/2" BSP (F) | Open Outlet bar | 65 °C | Grohe | faceplate | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| DS3007 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable | ||
| DS5010 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable |
Range of bib and hose union taps incorporating either brass or DZR brass (142HU prefix models only) bodies and non-rising spindle headworks. The FGK suffix models incorporate a ferrule guard and key (lockshield). The inlet and outlet of the 142HU (508107) and 142HU FGK (501117) models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperatures: 142HU (508107) and 142HU FGK (508117) models 65°C, all other models 90°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20302.G15.CP5R-8510 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8510 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8511 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20362.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet |
Wall Mounted Undefinable air gap see IRNs Incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.
‘TAQ PEX’ range of PEX lined flexible hose assemblies with either stainless steel braiding or grey polymeric (PET - Polyethylene terephthalate) braiding. G3/8" captive nut connection includes an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Hoses with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. The captive nut end connections incorporate a washer, the M10 connection incorporates an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Excelsior Range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 86005640 | Chrome | 15mm compression joint | 10 bar | 80 °C | TRITON,86005640 | Handle/ body | No | Ceramic cartridge |
Wall mounted, concealed shower valve (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating members and a manual diverter to shower outlets with a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, manually operated, concealed shower valves (stainless steel bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a ceramic disc diverter (models SD4373-2S) with various operating members. A quarter turn ceramic disc headwork (models SH40001-2, SD4373S) or 2 quarter turn ceramic disc headworks (model SH40001). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate backflow protection. Models SH40001-2, SH40001 incorporate stainless steel strainers. Supplied with a shower hose, shower handset, riser rail & overhead shower outlet (models SD4373-2S, SH40001). SD4373S incorporates a shower hose, shower handset & riser rail. SH40001-2 incorporates an overhead shower outlet Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C. Model SH40001 Maximum operating temperature 60°C
Wall mounted, concealed, thermostatic blending valve incorporating a thermostatic cartridge with a dome operating member and supplied with a trim set. Each inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 6 of 7
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
