Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.
Range of vertical multistage booster pumps, with stainless steel bodies and impellors. Maximum working pressure: See models Maximum working temperature 85°C.
Range of shower handsets with a black plastic body and EPDM ‘O’-rings. Model includes a trigger mechanism that alters the spray pattern. Maximum operating temperature 60°C.
Range of shower handsets with chrome plated ABS bodies incorporating NBR o rings. Maximum operating temperature 60°C.
Range of shower handsets (chrome plated brass), shower hoses, handset brackets and cover plates. The shower handset inlets incorporate stainless-steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60.0°C
Range of shower handsets with plastic bodies (chrome plated or white finish). Maximum operating temperature 60.0°C
Range of shower handsets and shower heads. The shower handsets have a plastic body (white), NBR ‘O’-rings, and a coloured locking ring around the shower face (see model section). The shower heads have a plastic body (white or chrome plated 02-093173 model), NBR ‘O’-rings, directional adjustment (ball joint) and a coloured interlocking ring either surrounding or central to the shower face (except for the 02-093165 and 02-093173 models which have no ring). The Wall shower T-L models have a combined NBR washer and stainless steel strainer on the inlet.
Wall mounted shower head arm incorporating a chrome plated brass body and EPDM O-rings. Maximum operating temperature 85°C.
Overhead shower outlet with a chromium plated brass body. The inlet incorporates a plastic flow restrictor. Maximum operating temperature 60°C.
Pillar tap incorporating (chromium plated) brass body quarter turn ceramic disc headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C. The product is supplied with metal backnuts.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever, dome type or cross top operating members and plastic backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wholesome-water nickel plated brass manifolds for use with ‘Emmeti Gerpex RA’ Pexb/Al/Pexb Multilayer pipe and ‘Emmeti Alpert’ PERT/AL/PERT Multilayer Pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. Range of closed circuit use nickel plated brass manifolds for use with ‘JG Speedfit Layflat Polybutylene Barrier Pipe (models 10BPB & 15BPB)’. Maximum working pressure 3.0 bar. Maximum operating temperature 92°C.
Wall mounted, exposed, manual blending valve (brass body, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, thermostatic blending valves (chrome plated brass bodies) incorporating quarter turn ceramic disc headwork with a single lever operating member. Temperature is independently controlled via a thermostatic cartridge with cross top operating members. Both inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, thermostatic blending valves (chrome plated brass bodies) incorporating quarter turn ceramic disc headwork with a single lever operating member. Temperature is independently controlled via a thermostatic cartridge with cross top operating members. Both inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork controlling the flow with dome operating member incorporating a manual override button. The temperature is controlled by a thermostatic cartridge with dome or cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with cube type operating member. Temperature is controlled independently via a thermostatic cartridge with a cube type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Electronically controlled thermostatic shower mixing valve with a plastic body. Temperature is controlled via two motorised valves and a thermistor. The product also incorporates a pump and plastic filters on each inlet. Maximum working pressure 7.0 bar. Maximum working temperature 65°C.
Range of wall mounted, concealed, thermostatic shower valves with cast brass bodies, incorporating a ceramic cartridge headwork controlling the flow with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted concealed diverter valves with a plastic body. The flow is controlled to two outlets via solenoid valves. Maximum working pressure 5.0 Bar. Maximum working temperature 65°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Manually operated thermally actuated regulating valves with bronze bodies and EPDM O-rings. Flow is controlled by a rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of pilot operated, adjustable, pressure reducing control valves, incorporating stainless steel bodies & strainers and EPDM ‘O’ rings & diaphragm. Auxiliary components include stainless steel tubing and isolation valves. The product is available with the following adjustable outlet pressures: 0 - 3.0 bar (silver spring), 1.0 - 8.0 bar (black spring), 1.0 - 16.0 bar (red spring). Maximum supply pressure 16.0 bar. Maximum operating temperature 65°C.
Range of spherical valves with brass (CW617N) or DZR brass (CW511L) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
Range of spherical valves (inline, angled and tee) with chrome plated brass bodies and ball. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. 140, 140M, 141 & 141M series models incorporate a stainless-steel strainer. 140 & 141 series models also incorporate a magnet. The 121 & 122 series models are 3-way valves. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Manifold spherical valve with DZR brass body and ball (chrome plated), incorporating a single lever type operating members and a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). For use with with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and wedge with either a lock shield or non-rising spindle operating mechanism for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 Bar Maximum operating temperature 95.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. with a a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle and a handwheel operating member with a brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 8.3 bar. Cold water use only.
'Endolac 245.30 FGC'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's technical data sheet dated 04/05/2022. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AO-96 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 571 ES Blue 536'. Factory applied, blue coloured polyolefin coating. Apply as per manufacturer's instructions dated '08/2022'. Cure for 20 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge 500'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 70:30 and apply as per manufacturer's Technical Data Sheet version edit '23/01/202. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NOA FWT BUFF/NOA FWT WHITE (ORGA1000 NOA BUFF/ORGA 1000 NOA WHITE). NOA FWT BUFF/NOA FWT BULE (ORGA1000 NOA BUFF/ORGA 1000 NOA BULE). NOA FWT BUFF/NOA FWT CREAM (ORGA1000 NOA BUFF/ORGA 1000 NOA CREAM)'. Factory applied, two-component white, blue & cream coloured epoxy coatings. Mix base and hardener in a 3.71:1 volume ratio and apply as per manual reference '14-11' dated 'July 2019 (ES)'. Cure for 16 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'UPS 505 WAU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet ‘TDS – UPS505WAU - Version 6 – August 2022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Belzona 5892'. Site applied, epoxy coating consisting of Belzona 5892 (white – Parts A & B) & Belzona 5892 (grey – Parts A & B). Belzona 5892 (white – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied as a first coat (no cure) in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. Belzona 5892 (grey – Parts A & B) are mixed in a weight ratio of 5.7:1 and then applied to the white in accordance with manufacturer’s instructions for use ‘FN10106’, publication number ’04-11-20(01)’. The final coating is then cured for 24 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Polyurea Rayston'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet dated 13/09/22. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Krypton Chemical, S.L. The authorization, training and certification of the local applicators are the responsibility of Krypton Chemical, S.L. and not the responsibility of WRAS.
'Interline 925 Cream'. Site applied, cream coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (yellow liquid) in a volume ratio of 3:1 and apply as per manufacturer’s TDS ref. ‘2252’ dated 17/12/2020. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Devi Flosto GRP (SMC) Hot Press Moulded Tank Panels' (manufactured from SMC 523/35). Grey coloured, hot press moulded GRP panels with a thickness of between 3.0mm & 16.0mm. For use with water up to 23°C.
'Silicopaste 312500'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
‘VP1620-WR & VP-2020-WR’. Single layer, cream coloured, extruded PEX-b tubes. For use with water up to 85°C.
‘Al Bilad Polyethylene and Polypropylene Pipes Factory HDPE Pipe’. Black coloured, extruded HDPE pipe. For use with water up to 65°C.
'SAPPCO PE100 Black Pipe'. Black coloured, extruded polyethylene pipe which has blue stripes on the outside. For use with water up to 65°C.
'Borfit HDPE Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'BorSafe ME3440 (black)'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'BorSafe HE3490-LSH'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
`Icorene 3560 Black 9001`. Black coloured, LLDPE material manufactured by rotomoulding. For use with water up to 85°C.
‘Lubricomp OFL36A-BK1B639 & Thermocomp OF008A-BK1B636’. Black coloured, injection moulded polyphenylene sulphide materials. For use with water up to 85°C.
‘Ramofin PPH300G6NT’, Natural (appears cream in colour), injection moulded, polypropylene material. For use with water up to 85°C.
'Twineflon® R12D06'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Sigma 511 (pink), Sigma 500 (blue) and Sigma 588 & 600 (white)'. PTFE sheet materials manufactured by calendaring & sintering. For use with water up to 85°C.
'4360 'O' rings, washers, membranes and lip seals'. Black coloured, injection moulded EPDM components with a shore hardness of 60. The ‘O’ rings have a tested in-radius size of 1.31mm. The washers have a tested in-radius size of 1.05mm. The membranes have a tested in-radius size of 1.55mm. The lip seals have a tested in-radius size of 0.40mm. For use with water up to 85°C.
'EP 856 gaskets and 'O'-rings'. Black coloured, injection moulded 'O'-rings with a tested in-radius size of 0.9mm. Black coloured, extruded gaskets with a tested in-radius size of 0.5mm. Both gaskets and 'O'-rings have a shore hardness of 80 and are for use with water up to 85°C.
'KEP EPDM Butterfly Valve Seat'. Black coloured, compression moulded EPDM sheet. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EP01961PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘KRE 60 (103), KRE 65 (100) & KRE 65 (106)’. In September 2022 ‘KRE 60 (104)’ was added to the approval. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60 & 65. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EX60LC, EX70LC & EX80LC'. Black coloured, compression moulded EPDM rubber materials. Shore hardness 60, 70 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
'HT5697-5'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 1.0mm. For use with water up to 50°C.
Black coloured, compression moulded EPDM materials with a tested in-radius size of 1.3mm. 'EPW-50, EPW-55, EPW-60, EPW-65, EPW-70 & EPW-75' have a shore hardness of between 50 & 75 and are for use with water up to 23°C. ‘EPW-80' has a shore hardness of 80 and is suitable for use with water up to 85°C.
'EH600-151'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'6741'. Brown coloured, compression moulded FKM rubber. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Addisil 2050E, 2060E, 2070E & 2080E'. Unpigmented (appear white, translucent), extruded silicone rubber materials. Shore hardness between 50 & 80. Tested in-radius size of 2.1mm. For use with water up to 85°C.
'Permabond ET5365'. Site applied, grey coloured, two-component epoxy adhesive consisting of part A (light grey coloured paste) & part B (dark grey coloured paste). The product cartridge is heated to 30°C and the two-components are mixed in a 2:1 volume ratio. Apply as per manufacturer's TDS 'revision 1', dated 23 May 2018. Cure 24 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VRSY6090 + Nylon 6.6 Rubber Expansion Joint'. Black coloured, compression moulded composite rubber expansion joint which consists of chlorobutyl/EPDM rubber & embedded polyamide fabric. Shore hardness 55. Tested in-radius size 2.0mm. For use with water up to 23°C.
Range of electronically controlled taps (chromium plated brass). The assemblies incorporate a touch sensitive device and are supplied with a solenoid valve to control the flow. Spout outlet incorporates a plastic aerator and the product is supplied with stainless steel strainers. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16 Bar. Maximum operating temperature 65°C
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and NBR or EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
Non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of hot-pressed sectional cold water storage cisterns for wholesome water. The cisterns can either be galvanised or primed and site coated and are fitted with a float operated valve, screened air vents, overflow pipe and breather. The cisterns can also be fitted with a coated, carbon steel ladder. Cold water use only.
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated, pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
‘Bubblestream’ range of tap outlet (stream shaper) adaptors incorporating a swivel mechanism and a stainless steel mesh aerator. All models, apart from 07.9870.0, are supplied with a M22 to M24 adaptor. All models, apart from 07.9870.0 & 07.9880.0, incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of aerators with plastic bodies and filter screens. Maximum operating temperature 60°C
Rising spindle headwork with a brass body intended to be inserted into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of ceramic disc headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic elements with copper bodies. Maximum operating temperature 90°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headworks and single lever operating members. The cold inlet to the tap incorporates incorporates an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2). The inlet of hose to the pull-out spray incorporates an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. The outlet of pull-out spray incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating a ceramic cartridge headworks with single lever operating members and a pull-out spray spout. The outlet incorporates a plastic aerator and single check valve cartridge however the product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single-hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating a ceramic cartridge headwork with a single lever operating member. The product has a pull-out spray outlet which incorporates a plastic aerator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The cold inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with pull-down hose. Incorporating a brass body (various finishes) and a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with pull-down hose. Incorporating a brass body (various finishes) and a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with single lever operating member and pull out spray handset. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Single hole, single outlet (swivel) combination tap assembly stainless steel (various finishes), incorporating a ceramic cartridge headworks with single lever operating member and pullout spray handset. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or for model SM BAS C an aerator with 4.5l flow limiter - flow limiter performance is not tested as part of the regulators specifications). The product is supplied with an approved click-type waste. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Single-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with an approved click-type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporates an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, brass bodies (various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied with approved pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator and the products are supplied with lever operated pop up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator and the products are supplied with a click waste. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet, fixed combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range single hole, single outlet swivel combination tap assemblies (brushed stainless steel) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass body). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator or flow straightener with a stainless steel and EPDM strainer. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The cold water inlet incorporate an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating quarter turn ceramic disk headworks with single lever operating members. The cold water inlets is supplied with a chrome plated brass adapter incorporating an approved check valve cartridge which has been verified by test (as suitable for backflow protection against Fluid Category 2) The spout outlets incorporate plastic aerators. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly with brass body (chrome plated), incorporating ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The cold water inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (with various finishes). Incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate plastic flow straighteners. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chromium or matt black finish), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, metal, single outlet (swivel) combination tap assemblies (chromium plated or brushed brass) incorporating a ceramic cartridge or ceramic discs headwork with either single lever or cross top. The spout outlets incorporate a plastic aerator. The cold inlet incorporates an optional check valve cartridge (excluding model HS605) which has been verified by test as suitable for backflow protection against Fluid Category 2. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies incorporating brass bodies (chrome plated) and a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic flow. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headwork and single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body - various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet can either incorporate a plastic aerator with an NBR washer or plastic flow straightener with a combined NBR washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout incorporates a waterfall outlet. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Wall mounted two-hole, single outlet, fixed, combination tap assembly (brass body, various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole combination tap assembly incorporating ceramic cartridge headwork with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Two-hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. This product is supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic straightener. The products are supplied with metal back nuts. Maximum working pressure 6 bar. Maximum operating temperature 65°C
Wall mounted, two-hole, single outlet (fixed) combination tap assembly, comprising of a concealed brass body, and a separate trim set (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated or matt black finished brass), incorporating quarter turn ceramic disc headwork with single lever operating members. The inlet incorporates a plastic flow restrictor. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disc headworks, each independently controlling the flow to a bath spout or shower outlet connection. Temperature is controlled independently via a thermostatic cartridge. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Wall mounted two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic disc diverter headwork controlling flow and diverters to either bath or shower via a dome operating member. A thermostatic cartridge controls temperature with a dome operating member incorporating a manual override button. The spout outlet incorporates a plastic aerator. Inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Spout supplied with an aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Two-hole, deck mounted single outlet (fixed) combination tap assemblies incorporating brass body (chrome plated), quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assembly with brass body, incorporating quarter turn ceramic disc headworks with either single lever or cross top operating members. The spout outlet incorporates a plastic areator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headwork with single lever type operating members and manual, bath to shower diverter. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The spout outlets incorporate a plastic aerator Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.
Range of bath shower mixers with (chrome plated brass bodies). The products have a manual bath to shower diverter with a single lever operating member and quarter turn ceramic disc headworks with cross-top operating members. The product is supplied with a shower hose, handset, and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks and a manual diverter to the shower outlet with either cross top or single lever operating members. Some models are supplied with shower hose and handset. The spout outlet incorporates a plastic aerator and the shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a thermostatic cartridge headwork controlling temperature with a manual override and a quarter turn ceramic disc controlling flow with a manual override and available with a range of dome and lever operating members. The assemblies also incorporate a lockable self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Two hole, double outlet swivel combination tap assembly ( stainless steel body) incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. The product is supplied with metal backnuts. The spout incorporates a mixed hot water outlet and separate outlet intended to be supplied by an instantaneous water heater (not included on this approval) to dispense near boiling water. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Three hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with a pop-up waste and stainless steel braided, PEX lined hose assemblies for connecting the headworks to the spout outlet. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies (brass with various finishes). Incorporating quarter turn ceramic disc headworks with cube type operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a click waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow regulator and a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spout outlet with brass body, incorporating aerator, available in different finishes. Maximum operating temperature 65°C.
Range of three-hole, single outlet wall mounted spout outlets with trim sets and operating members (chrome plated brass) incorporating a plastic aerator. Model PT05LS is supplied with cross-top operating members. Model PT06LS is supplied with single-lever operating members. Products are supplied with a click type pop up waste, (verified by test). Maximum operating temperature 65°C
In-line water filter system comprising of a head and replaceable carbon block cartridge (within a fixed housing) for use with John Guest LLDPE pipe. Maximum working pressure 8.6 bar. Cold water use only.
Smartpress range of crimped press-fit fittings with stainless steel, PPSU or gunmetal bodies for use with Viega Smartpress/Pexfit Pro multilayer (PE-Xc/AL/PE-Xc) pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of solder ring copper fittings for use with copper tube to EN 1057. The 304756, 110804, 304574, 304615 & 304711 models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘WSR S/R’ Range of solder ring copper fittings for use with copper tube to BS EN 1057. Maximum working pressure 16 bar. Maximum working temperature 99°C
Range of compression fittings with brass brass bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘KSO’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). The KSO14 sand KSO15 tap connector models incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Timco - Elysee range of Polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Jason range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of black coloured, PE100 butt fusion fittings for use with PE100 pipes (manufactured to EN 12201). Maximum working pressure for fittings used with SDR11 pipe is 16.0 bar and for fittings used with SDR17 pipe is 10.0 bar. For above and below ground use. Cold water use only.
Range of end feed copper fittings for use with copper tube to EN 1057. The 950513, 950514, 950501, 950503 & 950502 models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Brass fitting Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Cold water use only.
Mitsubishi PPSU elbow fitting with a quick connect clip. Maximum Working Pressure: 6 Bar Maximum Working Temperature: 80°C
Range of single and twin shower booster pumps with plastic bodies and impellers. The pump body inlet incorporates a combined EPDM washer and stainless steel strainer. Maximum working pressure: PL45 & PL45S models - 1.5 bar, PL65 & PL65S models - 2.0 bar. Maximum operating temperature 65°C.
Horizontal end suction centrifugal pump with a 316 stainless steel casing, impeller and shaft. Maximum working pressure 16 bar. Maximum operating temperature 100°C
Range of overhead shower outlets (chrome plated brass bodies) supplied with 4, 6, 9 way connectors and stainless-steel or nylon braided EPDM lined flexible hoses.. Maximum operating temperature 60°C.Open outlet only
Range of angled shower wall outelts with brass bodies (various finishes - see model). The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Overhead shower outlet with a chromium plated brass body. The inlet incorporates a plastic flow restrictor. Maximum operating temperature 60°C.
Range of disposable shower kits, consisting of shower handset and shower hose with EPDM ‘O’-rings. Maximum operating temperature 65.0°C.
Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of shower handsets with ABS bodies available in various finishes. Maximum operating temperature 85°C.
Range of chrome plated hand showers with plastic bodies. The inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
A range of overhead shower outlets with chromium plated brass bodies. The inlet of all models incorporate plastic filters. The inlet of all models, except 28.778.000, incorporate plastic flow restrictors. Maximum operating temperature 60°C.
Gold effect plated brass, wall mounted shower arm and head. The inlet of the shower head incorporates a plastic flow regulator. Maximum operating temperature 60°C.
Range of shower handsets with chrome plated plastic bodies. The inlets incorporate a plastic flow regulator and strainer. Maximum operating temperature 60°C.
Tempomix 3 794BOX1 concealed, wall mounted shower valve (brass body) for use with Tempomix 3 794218 & Tempomix 3 794219 functional/trim (chromium plated brass) kits. The functional/trim kits incorporate a self-closing spring-loaded headwork with a dome type operating member that controls both flow and temperature. 794219 also incorporates a chrome plated brass shower outlet that has a flow regulator. The inlets to the 794BOX1 incorporate stop valves, plastic filters and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Overhead shower outlets with brass bodies (various finishes), incorporating EPDM O rings. Maximum working pressure: Open outlet Maximum operating temperature 60.0°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Wall mounted bib taps (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of draining taps with a brass or chrome plated brass (337020 CST model) body, rising spindle headwork, and EPDM seals and washers. Maximum working pressure 10.0 bar. Maximum operating temperature - 337221,337231 and 337004 CST models: 85°C, all other models: 65°C.
Range of pillar taps (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Pillar taps (chromium plated brass) incorporating a quarter turn ceramic disc headwork with a single lever operating member. The spout outlets incorporate a plastic flow straightener. Model are supplied with plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Pillar taps (chromium plated brass) incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of stainless steel or nylon braided, PEX lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘S800’ flexible reinforced hose assembly with dual layered (black inner & grey outer) and PVC lining with a plastic strainer. Maximum working pressure 10.0 bar. Hoses manufactured from 2023: Maximum operating temperature: 60°C
Range of PVC or EPDM lined shower hoses with stainless steel outer (chrome or black finish) or PVC reinforced (chrome plated finish) outer layer. Maximum operating temperature 65°C.
Range of PVC lined shower hoses with black inner layer and silver plastic outer layer. Maximum operating temperature 60˚C.
Range of stainless steel interlocked (H35 models) or nylon braided (H36 models) flexible hose assemblies. H35 models are available with either a silicone or TPE liner, the H36 models are available with a TPE liner only. Maximum operating temperature 60°C.
Range of stainless steel or nylon braided, PEX or EPDM inner liner flexible hose assemblies available in a range of various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of CENTERSTORE AIR bubble top indirect and direct single coil unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 10.0 bar@90˚C. A safety kit (manifold) consisting of a single check valve assembly, verified by test (suitable for backflow prevention against fluid category 2), strainer, an expansion relief valve set at 8.0 bar and a pressure reducing valve set at 3.0 bar and a tundish is also provided. Alternative inlet control group and temperature and pressure relief valve added March 2023. Maximum working pressure: Secondary circuit: 7.5 bar. Primary circuit: 6.0 bar. Maximum operating temperature 65°C.
Range of indirect unvented indoor heat pump storage cylinders which consist of a heat pump which sits on top of the tank and heats the hot water via refrigeration pipes which then heats the cylinder by being externally mounted around the cylinder. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum working pressure 6.0 Bar (Secondary) Maximum operating temperature 55.0°C
Range of wall mounted, exposed, thermostatic shower mixing valves (chromium plated brass). The products incorporate a ¼ turn ceramic disc or a 2-way ceramic disc diverter headwork (see model). Temperature is controlled independently via a thermostatic cartridge with a manual override button. The products have cube (81B, 81C, 90B and 90C suffix models) dome type (all other models) operating members. Models (GR-LY-13BK2 & GR-LY-13BK4) incorporate single lever operating members. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valve (matte black plated brass), incorporating a ceramic disc diverter valve controlling the flow and a thermostatic cartridge independently controlling the temperature incorporating a manual override button, both using cube type operating members. The inlets incorporate stainless steel strainers with EPDM O-rings and approved check valve cartridges; however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower handset, shower hose, overhead shower, and riser rail assembly. The shower hose and overhead shower incorporate stainless steel strainers with EPDM O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves (chrome plated brass). Flow is controlled by a ceramic disc diverter cartridge, using dome type operating members. Temperature is controlled independently via a thermostatic cartridge using a dome type operating member which also incorporates a manual override button. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Electronically controlled thermostatic shower mixing valve with a plastic body. Temperature is controlled via two motorised valves and a thermistor. The product also incorporates a pump and plastic filters on each inlet. Maximum working pressure 7.0 bar. Maximum working temperature 65°C.
Wall mounted thermostatic shower valve (chromium plated brass bodies), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Range of wall mounted thermostatic shower valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. Both inlets incorporate approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Wall mounted, exposed, thermostatic shower mixing valve (chromium plated brass). The product incorporate a ¼ turn ceramic disc or a 2-way ceramic disc diverter headwork (see model). Temperature is controlled independently via a thermostatic cartridge with a manual override button. The product has a dome type operating member. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Wall mounted, bar type, thermostatic shower mixer (chromium plated brass), incorporating a 2-way ceramic disc diverter headwork with a dome type operating member controlling the flow between each shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with a shower hose (metal interlocked), shower handset (chrome plated), riser rail and overhead shower. The shower handset and the overhead shower both incorporate a stainless-steel strainer on the inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, exposed, thermostatic shower mixing valves (chromium plated brass). The products incorporate a ¼ turn ceramic disc or a 2-way ceramic disc diverter headwork (see model). Temperature is controlled independently via a thermostatic cartridge with a manual override button. All models have cube operating members except model 706128 which has dome operating member. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic blending valve (chromium plated brass). Temperature is controlled via a thermostatic cartridge with a cube operating member incorporating a manual override and the flow is controlled via two push type cartridges for the shower outlets. The inlets incorporate stainless steel strainers and approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, thermostatic shower valves with brass bodies (various finishes), incorporating a thermostatic cartridge controlling the temperature and a push shut-off valve controlling the flow. The inlets and the shower outlet incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Wall mounted, manually operated blending valve with a brass body (various finishes) and ceramic cartridge headwork a single lever operating member. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of wall mounted, thermostatic shower valves with brass bodies (various finishes). Flow is controlled with a ceramic disc headwork with a single lever operating member. Temperature is controlled independently by a thermostatic cartridge with a single lever operating member with a manual override button. Each inlet incorporates a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Wall mounted, manual blending valve (brass body, various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. This product is not claimed to provide any backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of thermostatic shower panels incorporating a single sequential thermostatic control valve with a single lever operating member and flexible riser kit. Each inlet supplied with a servicing valve, EPDM o-ring and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with black lined PVC shower hoses and chrome plated shower handsets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted concealed thermostatic blending valves with plastic bodies (various finished face plates). The flow is controlled by a ceramic disc diverter headworks with a cube type operating members. The temperature is controlled by a thermostatic cartridge with dome type operating members incorporating a manual override button. Both inlets incorporate an approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower valve with brass body (various finishes), incorporating a ceramic disc diverter that controlling the flow with a cube type operating member. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. The valves are either handwheel and gear operated (Models SD-BVG16 and SD-16BVLL) or lever operated (Models SD-BVL125 and SD-16BVGL). Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Deck mounted flow control valves incorporating quarter turn ceramic disc headworks with single lever operating members, accompanied by a self-cancelling diverter with a dome type operating member diverting the flow between two outlets. The product is supplied with stainless steel braided silicone lined flexible connecting hoses and one outlet hose, as well as a further stainless steel braided PEX lined flexible outlet hose. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of inline manually adjustable pressure reducing valves with DZR brass or bronze bodies (see model), EPDM diaphragm, seat washers and ‘O’-rings. Adjustable outlet pressures between 1.0 and 7.0 bar. Maximum inlet supply pressure Art.229.0XX: 40.0 bar, Art.229.1XX: 25.0 bar. Maximum operating temperature 80°C.
Range of inline manually adjustable pressure reducing valves with DZR brass or bronze bodies (see model), EPDM diaphragm, seat washers and ‘O’-rings. Adjustable outlet pressures between 1.0 and 7.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass, gunmetal or stainless-steel bodies. Maximum inlet pressure for HP and SP Models = 25.0 bar. Maximum inlet pressure for LP Models = 6.0 bar. Between September 2022 and December 2023, the maximum operating temperature of models included on the approval was 60°C. From January 2024, the maximum operating temperature of those models increased to 85°C. Models added to the approval in January 2024: Models with maximum working pressure of 6.0 & 16.0 bar models are for cold water use. Models with maximum working pressure of 25.0 bar have a maximum operating temperature of 85°C.
Range of combination valves with a DZR brass body incorporating a pressure reducing valve, a ball valve, pressure gauge and water meter port. The outlet incorporates two single check valve cartridges, verified by test suitable for backflow to fluid category 3. Maximum working pressure 16 Bar Outlet pressure in the range 6.0 to 1.5 bar. Maximum operating temperature 80°C
Premix control unit for an infrared sensor tap comprising of a solenoid valve with plastic body, EPDM diaphragm and ‘O’-rings, and silicone seals. Both the cold and hot inlets incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The central section of the valve incorporates a plastic strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a brass body, chrome plated brass ball, and lever operating member. Maximum working pressure 25.0 bar. Maximum operating temperature100°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 999698) Maximum working pressure 25.0 bar (model 496877) Maximum working pressure 40.0 bar (models 570500 & 570622) Maximum operating temperature 85°C.
Manifold spherical valve with DZR brass body and ball (chrome plated), incorporating a single lever type operating members and a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). For use with with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. 140, 140M, 141 & 141M series models incorporate a stainless-steel strainer. 140 & 141 series models also incorporate a magnet. The 121 & 122 series models are 3-way valves. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Range of lock shield or handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The V23AR16 & F23AR25 models have a rising spindle, the V23A16 & F23A25 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line screw-down stop valves with brass bodies, incorporating rising spindle headworks and EPDM washers. For use with BS EN 1057 copper pipe. Maximum working pressure 16 Bar at 30°C, 5 Bar at 99°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Ultra violet disinfection units consisting of a stainless steel body and quartz sleeve. Model WS-10-1206/3030031 Alde Aquaclear has a maximum working pressure of 5.0 bar and a maximum operating temperature of 40°C. All other models have a maximum working pressure of 7.0 bar and a maximum operating temperature of 60°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'Primgreen LAT 12035 & Unbrako wiscoat polyamide 11, ESY Blue 7265' coating system. Factory applied, blue coloured, polyamide powder coating system. Apply primer (Primgreen LAT 12035) and top coat (Unbrako wiscoat polyamide 11, ESY Blue 7265) as per user instructions ‘TSW/PR/02 REVISION A dated: 13.02.2012’. Cure both primer and topcoat for 12 minutes@215°C (each). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Endoprene 888.56'. Factory applied, beige coloured, two-part PU coating. Mix Parts A & B in a 75:25 volume ratio and apply as per Technical Data Sheet dated 09/12/2020. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valve Green Powder Coating Pulver 010'. Factory applied, green coloured epoxy resin coating. Apply as per manufacturer's data sheet ‘FR.07.03.18 Rev. 01 08.03.2021', issued '30.03.2022'. Cure for 10 minutes@160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPL Gold Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resisting Portland Cement. Mix cement, sand and water in a 1.0:1.4:0.35 mass ratio and apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours at 27°C & 70% RH. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic 840 ES'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet dated 16/05/2022. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Sika UAE L.L.C The authorization, training and certification of the local applicators are the responsibility of Sika UAE L.L.C and not the responsibility of WRAS.
'Fosroc® Polyurea WPW'. Site applied, blue coloured, two-component polyurea coating consisting of Component A (blue coloured) & Component B. Mix & apply as per manufacturers datasheet dated September 2022. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Fosroc International. The authorization, training and certification of the local applicators are the responsibility of Fosroc International and not the responsibility of WRAS.
'Silicone Greases PH041, 665016-TUB, 665016, PHCB041, 665017 & ASG50'. White coloured silicone greases. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'F15220 Center Silicone Lubricant'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'OP-90601' (orange coloured) & 'IP-90604' (light orange coloured). Injection moulded polyester materials. For use with water up to 50°C.
‘Dura-Line HD100 B Pipe’. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 60°C.
'NTG PE100 Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Supreme PE Electrofusion Fittings'. Black coloured, injection moulded polyethylene (PE 100) electrofusion fittings. For use with water up to 65°C.
'DR-PLAST HDPE PE-100 Pipes'. Black coloured (with dark blue stripe), extruded HDPE pipe. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Fittings'. Black coloured, HDPE fittings manufactured by either injection moulding or butt fusion welding. For use with water up to 60°C.
'Aura HDPE Electrofusion Fittings'. Black coloured, injection moulded HDPE (PE100) electrofusion fittings. For use with water up to 65°C.
'Eltex PC002-50R968'. Light blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'BorSafe HE3490-LS'. Black coloured, extruded PE material. For use with water up to 60°C.
'H600042'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 65°C.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘SBPEP4555 (50), SBPEP55 (55), SBPEP60 (60), SBPEP65 (65), SBPEP70 (70), SBPEP75 (75) & SBPEP7085 (80)’. Black coloured, compression moulded EPDM rubber sheet materials with a shore hardness of between 50 & 80. Tested in-radius size of 1.0mm. For use with water up to 60°C.
'E6083AA'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP601289C'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'KRE70 (80-3)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EP6007K'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘TEC S27 R.-70 rosso washers & ‘O’ rings’. Red coloured, injection moulded VMQ washers & ‘O’ rings with a shore hardness of 70. The washers have an in-radius size of between 0.5mm & 2.6mm. The ‘O’ rings have an in-radius size of 0.5mm. From March 2024 the in-radius size range of the ‘O’ rings was extended to between 0.5mm & 2.6mm. For use with water up to 85°C.
Range of wall mounted electric showers with plastic bodies. Flow is controlled by a solenoid. The product is supplied with a shower hose and a shower handset (white or chrome plated - depending on model). Maximum working pressure 8.0 bar. Maximum operating temperature 55°C.
'SAPPCO uPVC Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 65°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. The products are supplied with plastic backnuts and a stainless steel braided PEX lined flexible hose assembly for installation between the tap and the solenoid valve. The HK-Cha models added September are also supplied with a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of flow restrictors with plastic bodies and EPDM ‘O’-rings available in a variety of colours (see models). Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies stainless steel (various finishes), incorporating a ceramic cartridge headworks with single lever operating member and pullout spray handset. The spout outlet incorporates a plastic aerator and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating a ceramic cartridge headwork with single leaver operating member. The spout outlet is a pull-out spray type incorporating a plastic aerator. The pull-out hose inlet connector incorporates an approved check valve cartridge, however, , the complete assembly has not been tested to demonstrate it provides backflow prevention Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pull-down hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole, fixed combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates plastic flow aerator. The product is supplied with a brass open outlet adaptor for the spout. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) Models KT41, KT42, KT43, KT44, TARAVO CH, TARAVO GUNMETAL, TARAVO BN, TARAVO COPPER, TARAVO GOLD & TARAVO MB incorporate a ceramic cartridge headwork with a single lever operating member All other models incorporate ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, chrome or black finish) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a spring-loaded pull-down hose incorporating a spray handset with trigger mechanism that controls the spray. The spray handset incorporates a plastic aerator at the outlet. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model), comprising of a concealed rough in set (brass) incorporating a ceramic cartridge headwork and a trim set consisting of a spout and a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members (M3206) or cross top operating members (M3106). The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C. The product is supplied with shower hose and handset.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating members and a ceramic disk diverter with cube type operating member controlling the flow between the outlets. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of exposed bath fillers (brass body, various finishes) incorporating a ceramic cartridge headwork, controlling both flow and temperature with a single lever operating member. The products incorporate integrated overflow and click type pop-up waste systems. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, two single outlets (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating ceramic cartridge headwork, single lever operating member controlling both flow and temperature to the spout and spring-loaded pull-down hose. The pull-down hose incorporates a hand spray with a self-closing trigger mechanism. The spout incorporates a ceramic disc headwork controlling the flow with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted spout outlets with stainless steel bodies incorporating plastic aerators. Maximum operating temperature 60°C
Wall mounted, bath spout outlet (chromium plated brass) incorporating a plastic flow straightener. Maximum operating temperature 60°C. Max operating pressure 5.0 bar.
Range of indirectly heated stainless steel vented hot water storage cylinders. Maximum working pressures: Primary: 6.0 Bar Secondary: 6.0 Bar Maximum operating temperature 75.0°C
Range of expansion vessels with galvanised or stainless-steel inlets, incorporating butyl rubber diaphragms. The inlet incorporates a plastic strainer (all models, except for WD model). For maximum working pressures please refer to model.
Non-metallic materials and components comply with BS6920 at 70°C
Mapress range of stainless steel crimped fittings and stainless steel pipe. The joint is achieved by a crimped fitting. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Uponor ‘Q&E Shrink-Fit’ range of plastic (PPSU) or brass fittings for use with Uponor Radi pipe (PEX): 12mm, Uponor Combi pipe (PEX/EVOH/PEX): 16-40mm, and Uponor Aqua pipe (PEX): 40-63mm. Jointing is achieved via swaging tool. Uponor ‘Q&E’ adapters for soldering, solder ends are for use with copper pipe (manufactured to EN 1057). Operating parameters when used with the following pipes: 12mm Radi pipe, 16-25mm Combi pipe and 40-63mm Aqua pipe: Maximum working pressure 12.0 bar @ 20°C. Maximum working pressure 6.0 bar @ 95°C. From November 2022: 32-40mm Combi pipe: Maximum working pressure 12.0 bar @ 20°C. Maximum working pressure 6.0 bar @ 70°C.
Range of solder ring copper fittings for use with copper tube to EN 1057. The SRBTC015, SRBTC022, SRSTC015, SRSTC022 & SRSTC015 Models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of solder ring copper fittings for use with copper tube to BS EN 1057. Maximum working pressure 16 bar. Maximum working temperature 99°C
Range of solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Henco Press Brass (P) and Henco Press Black coloured (PK) ranges of press fit fittings (brass or PVDF bodies) for use with Henco RIXc PEXc/Al/PEXc pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘Mapress’ range copper or copper and brass “copper-press” fittings with butyl rubber (up to 54mm) or EPDM rubber (>54mm) ‘O’-rings for use with copper pipe to BS EN 1057. For above ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Aquaflow range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Dual flush WC outlet valve incorporating an ABS body, operated via a push button assembly or a battery powered infra red sensor for either full or reduced flush. Cold water use only.
Range of plate heat exchangers with stainless steel plates, for primary and secondary circulation. Models E040-2M-GB6 and R040-H2M-G6B are secondary use only. Maximum working pressure - R040-HNM-G6B range = 30.0 Bar and E040-NM-GB6 range = 20.0 Bar Maximum operating temperature - 99 °C
Alfa Laval range of copper brazed and stainless-steel fusion bonded, stainless steel heat exchangers in various sizes ranging from 4 plates to 300 plates. Maximum working pressures and temperatures: CB10, CB11, CB15, CB16, CB16AQ, CB18, CB18AQ & CB18DW: S1/S2 circuit: 5 Bar. S3/S4 circuit 10 Bar. Max working temperature 150°C. CB20 & CB20AQ: S1/S2 circuit: 16 Bar. S3/S4 circuit 16 Bar. Max working temperature 225°C. CB65, CB65AQ & CBH65: S1/S2 circuit: 18 Bar. S3/S4 circuit 37 Bar. Max working temperature 225°C. CBH16 & CBH18: S1/S2 circuit: 32 Bar. S3/S4 circuit 32 Bar. Max working temperature 150°C. Maximum operating temperatures detailed above are for primary circuits only, secondary circuits approved to 99oC. Models added March 2023: CBH30: 50 Bar (S1/S2/S3/S4) & 225.0°C, CBH112: 45 Bar (S1/S2) 51 Bar (S3/S4) & 225.0°C, CB30: 41 Bar (S1/S2/S3/S4) & 225.0°C, CB60: 40 Bar (S1/S2/S3/S4) & 225.0°C, CB60AQ: 40 Bar (S1/S2/S3/S4) & 225.0°C, CBH60: 40 Bar (S1/S2/S3/S4) & 225.0°C, CB62: 40 Bar (S1/S2/S3/S4) & 225.0°C, CB62AQ: 40 Bar (S1/S2/S3/S4) & 225.0°C, CBH62: 40 Bar (S1/S2/S3/S4) & 225.0°C, CB30AQ: 40 Bar (S1/S2/S3/S4) & 225.0°C, CB110: 37 Bar (S1/S2/S3/S4) & 225.0°C, CB110AQ: 37 Bar (S1/S2/S3/S4) & 225.0°C, CBH110: 37 Bar (S1/S2/S3/S4) & 225.0°C, CB112: 37 Bar (S1/S2/S3/S4) & 225.0°C, CB112AQ: 37 Bar (S1/S2/S3/S4) & 225.0°C, CB24: 29 Bar (S1/S2) 37 Bar (S3/S4) & 225.0°C, CB24AQ: 29 Bar (S1/S2) 37 Bar (S3/S4) & 225.0°C, ANTW66: 29.0 Bar (S1/S2/S3/S4), ANTW18: 23 Bar (S1/S2) 28 Bar (S3/S4) 225.0°C and RM11: 15 Bar (S3/S4) & 225.0°C. Maximum operating temperatures detailed above are for primary circuits only, secondary circuits approved to 99oC.
Range of wall hung, gas fired, combination boilers providing domestic hot water via a plate heat exchanger. The primary circuit incorporates an integral expansion vessel and a pressure relief valve set at 3.0 bar. The product is supplied with a rigid pipe filling loop, followed by a separate isolation valve. The filling loop pipe attaches to the cold water inlet valve which incorporates a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3) on the branch to the filling loop. The primary circuit includes an isolation valve on the flow and return and is also supplied with two loose 22mm compression isolation valves and a filter. Maximum working pressure of the primary circuit is 2.5 bar and the maximum supply pressure to the secondary circuit is 10.0 bar. Max operating temperature 65°C.
Range of static ultrasonic bulk water meters with stainless steel bodies and EPDM 'O'-rings. The products are supplied with two sets of optional (green) gaskets. Maximum operating temperature: Products marked T50: 65°C. Products marked T30: cold water use only.
Leak detection and prevention device consisting of an inline solenoid valve and flow meter. Maximum working pressure 10.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at 23°C
Range of solid copper alloy and bi-metallic flanges. Solid models are bronze, bi- metallic models are bronze with an epoxy coated steel outer flange.
Range of twin shower booster pumps with plastic bodies and impellers. The pump body inlet incorporates a combined EPDM washer and stainless steel strainer. Maximum working pressure: D01695 model 1.5 bar D01696 model 2.0 bar. Maximum operating temperature 65°C
‘Alpha’ range of circulator pumps with either a composite (plastic) or stainless steel body, plastic impellor and EPDM ‘O’-rings. The Alpha 1 model B CIL3 has a black motor housing. The Alpha 1 model B and the Alpha 2 model E stainless steel body models have either a black or red motor housing. All other models have a red motor housing. The 1”-1½” models are supplied with EPDM gaskets for the inlet and outlet. The 2” model has fibre/NBR gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower handsets (chrome plated brass bodies). The shower handset incorporates an approved check valve cartridge with a flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Plastic shower handset with flexible shower hose and brass wall outlet. Maximum operating temperature 60°C
Range of shower handsets with plastic bodies (various finishes - see model). The E082051.XXXAWZZ and E082073.XXXAWZZ models incorporate a combined TPE washer and stainless steel strainer on the inlet. Maximum operating temperature 65°C.
Range of chrome plated shower kits. Consisting of shower handsets, shower hoses that incorporate EPDM O-rings and riser rails. Maximum operating temperature 65°C.
Range of shower handsets incorporating chromium plated plastic or chromium plated brass bodies (see model). Inlets incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Pillar taps (chromium plated brass) incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with a single lever, dome, or cross top type operating member (see models). The spout outlet incorporates a plastic flow straightener. Models are supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with a single lever, dome, or cross top type operating member (see models). The spout outlets incorporate plastic flow straighteners. Models are supplied with metal backnuts. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of stainless steel or nylon braided, PEX lined flexible hoses with a variety of end connectors. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of PVC or EPDM lined shower hoses with stainless steel outer (chrome or black finish) or PVC reinforced (chrome plated finish) outer layer. Maximum operating temperature 65°C.
Range of stainless steel or nylon braided, thermoplastic silicone rubber (TPSiV) lined flexible hoses with a variety of end connectors. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of wall mounted concealed (BIV & BIR models) and exposed (EV model) thermostatic shower control valves. The bodies are cast brass (concealed versions) with a chromium plated trim set or chromium plated brass (exposed versions). Flow and temperature are controlled by a thermostatic cartridge with a single lever operating member. The inlets incorpoarate stainless steel strainers. Some models are supplied with a shower hose and handset or an overhead shower arm and shower head with flow regulator (see model section). The BIV model is also supplied with an angled wall outlet elbow. Maximum working pressure 5.0 bar. Maximum operating temperature 45°C.
Wall mounted, bar type, thermostatic shower mixer (chromium plated brass), incorporating a 2-way ceramic disc diverter headwork with a cube type operating member controlling the flow between each shower outlet. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with a shower hose (PVC), shower handset (chrome plated), riser rail and overhead shower (chrome plated). The overhead shower and the shower handset both incorporate a plastic flow regulator and a combined EPDM washer and stainless steel strainer on the inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, thermostatic shower mixers with brass bodies, dome or cube operating members and a thermostatic cartridge controlling the temperature. Models D1001, LB091, LB092, LB093, LB094, LB095, D2002, LB096, LB097, LB098, LB099, LB100, D3001, LB101, LB102, LB103, LB104 & LB105 incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted thermostatic shower valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. Both inlets incorporate approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of concealed, thermostatic blending valves with a brass body. The temperature is controlled via a thermostatic cartridge with a dome operating member which incorporates a manual override, and flow is controlled via a push on/off headwork to a single or optional shower outlet, depending on model. The inlet connections incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of gear or lever operated wafer, semi lugged or fully lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Manually operated thermally actuated regulating valves with bronze bodies and EPDM O-rings. Flow is controlled by a rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line adjustable pressure reducing valves with DZR brass bodies and NBR ‘O’-rings. The valve incorporates a test port. The outlet pressures range from 1.5 bar to 6.0 bar. Maximum supply pressure 25.0 bar. Cold water use only.
Bistable (latching - pulse controlled) or monostable (normally open) solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. The products incorporates a stainless-steel filer on the inlet. From February 2024 the product may also be supplied with a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature: Between October 2022 and January 2024 this product is suitable for hot water use only (70°C). From February 2024 to the end of October 2027 this product is suitable up to 70°C.
Range of spherical valves with brass (K65281, K65282, K65283, K65301, K65302, K65303, K65291, K65292, K65293, K65311, K65312 & K65313) or DZR brass (K64783, K64784, K64793, K64794, K64763, K64764, K64773, K64774) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, FKM ‘O’-rings or EPDM ‘O’-rings (S84W series only) and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle and a handwheel operating member. The 960985, 960986 & 960987 suffix models have a brass body and brass wedge, the 850066, 850070 & 850071 suffix models have a DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of commercial, front loading washing machines with flow controlled by a solenoid valve and discharged via type AB air gap assembly (verified by test, suitable for backflow protection against fluid category 5). The inlets incorporate a stainless-steel strainer. Maximum working pressure 6 Bar Maximum operating temperature 85°C
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'DWKRAL ABS BIANCO 4698 AT'. White coloured, injection moulded ABS material. For use with water up to 35°C.
'J6970 (white coloured) & J6990 (cream coloured)'. Compression moulded Aluminium Oxide Ceramic sealing rings. For use with water up to 85°C.
'CD 101 P6'. Grey coloured (opaque), ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Art-Coat'. Factory applied, colourless (transparent) PTFE based surface treatment coating. Apply as per manufacturer's instructions 'revision 3' dated 16-03-2020. Cure for 45 minutes@55-60°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lak Series 2000 - Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 25-1113: Description RAL5005 Blue Signal R.C. (dark blue coloured). Code 25-1117: Description RAL5015 Blue Sky R.C. (light blue coloured). Code 29-1116: Description RAL9005 Black Jet R.C. (black coloured). Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Series 2000 – Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 29-0008: Description RAL9005 Black Deep FBE. Code 25-0084: Description RAL5015 Blue Sky. Code 25-1110: Description RAL5005 Blue Signal. Code 23-0004: Description Red Oxide Primer. Code 25-1160: Description SABSF29 NCS Blue Cornf. Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Plascoat PPA571 Aqua Blue 536'. Factory applied, blue coloured PE coating. Apply by flock spray coating and fluidised bed dipping (and post-cure as necessary) in accordance with TDS dated 23/02/2015. Please refer to ‘guide to typical coating conditions – batch operation'. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPICOAT 1000'. Factory applied, two-component, red coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/006', 'version 01', dated '03.11.2022'.. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DICOAT 60EX'. Factory applied, two-component, blue coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/007', 'version 01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Teadit NA1006'. Green coloured NBR/fibre gasket material manufactured by mixing and calendaring. For use with water up to 65°C.
'Profood High Temp 2'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Everbuild Plumber's P12 Silicone Grease (Barcode: 5055492703842)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'Vesconite (Grey) and Vesconite Hilube (Cream)'. Extruded bearing material. For use with water up to 65°C.
'Grivory HT1V-5 FWA grey L2172.5'. Grey coloured, injection moulded PA6I/6T-GF50 material. For use with water up to 85°C.
'Mais' pipe. Black coloured (with blue external stripes), extruded, PE100 HDPE pipe. For use with water up to 65°C.
'Flow Reducer Bp V2 ½ 34 9957, Flow reducer Bp V2 ½ short 34 9965 blue & Flow reducer Bp V2 3/8 short 34 9966 blue’. Blue coloured, injection moulded HDPE flow reducers. For use with water up to 23°C.
'ITS PE100 Fittings'. Black coloured, extruded polyethylene fitting. For use with water up to 60°C.
'Neproplast HDPE PE100 Pipes'. Black coloured, extruded HDPE pipes. For use with water up to 60°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'Elysee PN16 Compression Fittings'. Black coloured, injection moulded polypropylene fittings. For use with water up to 23°C.
‘Ramofin PPH300G6BK11’. Black coloured, injection moulded, polypropylene material. For use with water up to 85°C.
'Duraseal SSAT'. Black coloured, silicone, self-fusing tape. Apply as per manufacturer's instructions 'version 3.2 (EN)' revised 26th August 2022. For use with water up to 65°C.
'TIMO-70 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
'EC-6509-A'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.5mm. For use with water up to 80°C.
'EP62/75'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 75. Tested in-radius size 3.5. For use with water up to 85°C.
'Selon 336'. Dark green coloured anaerobic sealant. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Selon 618'. Blue coloured, liquid PTFE anaerobic sealant. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'CURA Liquid (Part No. 19261)'. Blue coloured, liquid PTFE anaerobic sealant. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
‘Tubular’ range of wall mounted spout outlets (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The box assembly incorporates a solenoid valve, screwdriver operated spherical valve and the spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a dome operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 Bar Maximum operating temperature 65 °C
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assembly with chromium plated brass bodies. The flow is controlled by a solenoid valve activated via an infra-red sensor and a manually adjustable temperature lever. The inlet to the solenoid incorporates a stainless-steel strainer. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer and check valve cartridge(s), verified by test (suitable for backflow protection against Fluid Category 2). The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the spout to the solenoid. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar Maximum operating temperature - 60 °C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only
Concealed WC dual flushing cistern with a bottom entry BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure – 10.0 bar, cold water use only.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring and NBR or EPDM ‘O’-rings. To be housed in a specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C for 31.4232.0; 85°C for 31.0030.0.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (brass body, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates an integral plastic flow regulator and a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
'PCR-E' range of flow regulators with chrome plated brass housing and NBR sealing gaskets. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet is a pull-out spray type. The spout inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow prevention. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members on models (162438, 162438EX, 162938, 100848 & 100848A). Model (M3108) incorporates quarter turn ceramic disc headworks with cross-top operating members. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. Model (M3108) can also be supplied with a lever operated pop-up waste. Maximum working pressure - 10.0 Bar (M3108, 100848 and 100848A) Maximum working pressure - 5.0 Bar (162438, 162438EX, 162938) Maximum operating temperature 65.0°C
Single hole, single outlet fixed combination tap assembly (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with dome type operating members for the basin mixer model and a cross-top operating member for iflo tatton basin mixer model). The lever basin mixer incorporates quarter turn ceramic disc headworks with a single lever operating member. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating non-rising spindle headworks with dome type operating members for models (101221) and a cross-top operating member for model (101229 Henlake basin mixer ). Model (101226 Lever basin mixer ) incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assemblies with brass bodies (chrome plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with either a single lever or dome type operating member (see model). The spout outlet incorporates a plastic aerator (specific models only - see model section). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating a brass body and ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted single hole, single outlet combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever operating member and a self-cancelling diverter to shower outlet. The spout incorporates a waterfall outlet. The product is supplied with a stainless steel inter-locking shower hose & handset. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies). Model 922318 incorporates a ceramic cartridge headwork with single lever operating member. Model 922319 incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a flow straightener and is also supplied with an optional aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet can either incorporate a plastic aerator with an NBR washer or plastic flow straightener with a combined NBR washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) All other models incorporate ceramic disc headwork with single lever operating members. The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with various operating members (see models). The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, deck mounted single outlet (fixed) combination tap assemblies incorporating brass body (chrome plated), quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted, two hole combination tap assembly incorporating ceramic cartridge headwork with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout has a waterfall outlet. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 80°C.
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever or cross top (M3105 model only) operating members and a manual diverter to shower outlet. The spout outlets incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The product is also supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single operating members and a manual diverter to shower outlet. The spout outlets incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The product is also supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever or cross top (400147 model only) operating members and a manual diverter to shower outlet. The spout outlets incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The product is also supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two hole, metal, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating member and a manual diverter to shower outlet. The spout outlets incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The product is also supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc or ceramic cartridge headworks various operating members (see models) and a manual diverter to shower outlet. The spout outlet either incorporates a plastic flow straightener, plastic aerator or an open outlet (see models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Floor mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener, NBR washer with stainless steel strainer. The product is supplied with a stainless steel inter-locked shower hose with EPDM lining & handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. K-968M series incorporates non-rising spindle headworks with cross-top or dome operating members.The product incorporates a self-canceling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with a shower hose, shower handset and metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Floor mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener, NBR washer with stainless steel strainer. The product is supplied with a stainless steel inter-locked shower hose with EPDM lining & handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener and a NBR washer with a stainless steel strainer. The products are supplied with metal backnuts, stainless steel inter-locking shower hoses with EPDM lining and handsets. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate either a plastic flow straightener or plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members and lockable diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The outlets of the side valves each incorporate a combined EPDM washer and stainless-steel strainer and a brass adaptor, which connects to the spout via two stainless steel braided PEX lined quick connect hoses and a plastic Y-piece. The spout outlet is supplied by a brass inlet pipe which incorporates a plastic flow regulator, as well as a stainless steel braided PEX lined flexible hose assembly. The spout outlet incorporates a plastic aerator. The products are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass body with various finishes) incorporating quarter turn ceramic disc headworks and various operating members (see models). The products are supplied with or without a lever type operated pop-up waste (see models) and the spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Three-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating 1/4 turn ceramic disc headworks and single lever operating members. The product is supplied with plastic backnuts and a lever pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range three hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes – see model). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlets incorporate plastic aerators. The product incorporates ACB braided EPDM lined flexible connection hose assemblies incorporating M10 x ½” BSP (F) captive nut end connections. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of four-hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever or dome operating members and a self-cancelling diverter to shower outlet. The product comprises of a basic set including the main body, headworks and shower hose, along with accompanying trim sets which include the spout, self-cancelling diverter, shower elbow and handset. The spout outlet incorporates a plastic aerator. The product is supplied with a metal interlocked shower hose and handset. The shower handset of the 31 314 xxx model incorporates a plastic flow regulator on the inlet. The elbow attached to the shower handset incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of floor mounted spout outlets (stainless steel or brass body various finishes) incorporating a plastic aerator. Maximum working pressure: Open outlet use only Maximum operating temperature: 60.0°C
Chrome plated spout outlet. The spout outlet incorporates a plastic aerator. Maximum operating temperature 65°C.
Bath spout (brass body, various finishes - see model) incorporating a plastic aerator. Maximum operating temperature 60°C.
Range of filter heads with plastic bodies. Models with push-fit connections are for use with John Guest LLDPE pipes. Maximum working pressure 8.6 bar. Cold water use only.
Range of Protecta-line multilayer pipes manufactured to BS EN8588, PE100 63mm to 355mm and PE80 25mm to 32mm. For use with : Mechanical compression fittings: 25-32mm (PE80 pipe), 63mm (PE100 multi pipe) Electrofusion fittings: 63-355mm (PE100pipe) Mechanical clamp-on fittings: 63-180mm (PE100pipe) PE to Copper Pipe Coupler transition fittings are for use with copper pipe (BS EN 1057) For below ground use. Maximum working pressure: 10 bar when used with SDR17 PE100 Protecta-Line pipes 12.5 bar when used with SDR11 PE80 Protecta-Line pipes 16 bar when used with SDR11 PE100 Protecta-Line pipes 12.5bar when used with copper pipe.
‘Flowflex,’ ‘Lamontite’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of black polyethylene electrofusion fittings for use with PE100 pipe (manufactured to EN 12201-2). Please refer to model for maximum working pressures. For below ground and cold water use only.
Range of automatic urinal flush valves with a plastic body. STD - Maximum working pressure 6.0 bar. LP - Maximum working pressure 0.5 bar. Cold water use only
Range of plate heat exchangers with stainless steel bodies. Model B8LAS has a maximum working pressure of 45.0 bar. Model 85-M has a maximum working pressure of 46/32 bar. Model E5P has a maximum working pressure of 10.0 bar. Maximum operating temperature 100°C.
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of in-line ultrasonic water meters with epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with green coated, stainless steel bodies, stainless steel electrodes and an ebonite rubber liner. Maximum working pressures: DN20 - DN40: 40.0 bar. DN50 - DN200: 16.0 bar. DN250 - DN400: 10.0 bar. Cold water use only.
Range of commissioning valves incorporating integral test ports & DZR brass bodies. Maximum working pressure 20.0 bar. Maximum operating temperature 50°C.
Wall mounted shower outlet elbow with a chromium plated brass body incorporating EPDM ‘O’-rings. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
Range of water pressure booster pumps, comprising of a multi-stage pump with a brass body, and an expansion vessel. The product is supplied with a strainer and two stainless steel braided EPDM lined flexible hose assemblies. The outlet assembly incorporates a non-return valve, not suitable for backflow protection. Maximum working pressure models 46601 and 46602 6.0 bar, models 46622 and 46624 9.0 bar. Cold water use only.
Range of centrifugal multi-stage horizontal pressure booster pumps with brass bodies. The 46593, 46594, 46595 and 46610 models include a non-return valve (not suitable for backflow protection) and an expansion vessel. They are also supplied inline strainer and two stainless steel braided EPDM lined flexible hose assemblies with 1” captive nut x 1" BSP (M) end connection for the inlet and outlet. Maximum working pressure models 46578, 46596, 46605 and 46606: 6.0 bar, Models 46593, 46594, 46595 and 46610: 9.0 bar. Maximum operating temperature 65°C
Range of inline circulation pumps with a plastic body, plastic cover, plastic impellers, and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower handsets with ABS plastic bodies (various finishes, see models). Maximum operating temperature (see models).
Range of shower handsets with ABS plastic bodies (various finishes, see models).. Maximum operating temperature (see models).
Range of kits comprising of a shower handset, shower hose and riser rail (various finishes - see models). The shower hose incorporates an EPDM washer and stainless-steel strainer Maximum operating temperature 60°C.
A range of ABS plastic shower handsets, (various finishes - see model). Maximum operating temperature 60°C.
Range of deck mounted pull-out shower hose and handsets (various plated brass or stainless-steel bodies). The inlet to the shower handsets incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature: 60°C
Range of shower handsets with chrome plated brass bodies, available with various handle finishes and trim sets. Maximum operating temperature 65°C.
Over head shower outlet with a chromium plated brass body, with a swivel function. Inlet incorporates NBR gasket with stainless-steel strainer and a flow regulator. Maximum operating temperature 60°C.
Range of shower handsets incorporating flow regulators on the inlets available in chrome and matte black finishes. Maximum operating temperature 60°C.
Range of chrome plated shower kits consisting of shower hoses with EPDM washers incorporating stainless steel strainers at the captive nut, handsets and riser rail assemblies. Maximum operating temperature 60°C.
Range of overhead showers, shower handsets, shower kits and an angled wall outlet. The ARR-HEAD-CP overhead shower has a brass body and wall mounted arm (chrome plated). The CER-HEAD-C/P overhead shower has a plastic body (chrome plated) and incorporates a combined EPDM washer and stainless steel strainer on the inlet. The shower handsets have plastic bodies (chrome plated). The ARR-SFSRK+O-CP shower kit consists of an angled brass wall outlet (chrome plated), multi-layered PVC lined shower hose (silver external appearance), a plastic bodied shower handset (chrome plated) and a riser rail. The ARR-SFMKWO-CP shower kit consists of an angled brass wall outlet with integral handset holder (chrome plated), multi-layered PVC lined shower hose (silver external appearance) and a plastic bodied shower handset (chrome plated). Maximum operating temperature 60°C.
Range of shower handsets with ABS plastic bodies (various finishes, see models). Maximum operating temperature (see models).
Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of wall and ceiling mounted shower outlets with chromium plated brass bodies supplied with various styled chromium plated shower arms. The shower head inlet incorporates a flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Bib taps incorporating either brass or DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (brass body in various finishes) incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chrome plated brass) incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate plastic flow straighteners. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Stainless-steel or nylon braided PEX lined flexible hose assemblies with various end connections (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of nylon braided PEX lined flexible hose assemblies. Maximum operating temperature 60°C
Stainless-steel or nylon braided EPDM lined flexible hoses assemblies with various end connections (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Direct & Indirect stainless steel insulated unvented hot water storage cylinders with internal expansion. The secondary circuit consists of a temperature and pressure relief valve set at 10.0 bar and 90°C and an alternative temperature and pressure relief valve also set at 10.0 bar and 90°C , an inlet control group consisting of a pressure reducing valve pre-set at 3.0 bar, an expansion relief valve set at 8.0 bar, a strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) also supplied with a tundish. Maximum working pressure - Primary circuit: 6.0 bar & Secondary circuit: 7.5 bar Maximum operating temperature 85.0°C
Range of air vent valves with brass (covered with blue polyester coated ductile iron body) or plastic bodies and plastic floats. Maximum working pressure 16.0 bar (AP models) or 25.0 bar (AQ models). Cold water use only.
Range of wall mounted thermostatic blending valves (brass bodies), with ceramic cartridge headworks controlling the temperature and the flow and a manual diverter that diverts the flow to two outlets. Both have single lever operating members. Maximum working pressure 5.0 Bar Maximum operating temperature 65°C.
Range of wall mounted, manual, shower blending valves, comprising of a concealed brass body (rough in set) and a trim set (chrome plated), which includes a ceramic cartridge headwork with a single lever operating member. The 2551 and 2551EP trim set models also have a 90° wall outlet elbow. The 2541 and 2551 models are supplied with a combined plastic filter and plastic flow regulator (x2) for installation on each concealed body inlet. The 2541EP and 2551EP models are supplied with a combined plastic filter and an approved single check valve with a plastic flow regulator (x2), for installation on each concealed body inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The concealed rough in set incorporates a manually operated isolation valve on each inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic shower mixer with brass body (chrome plated), incorporating a ceramic cartridge headwork ,controlling the flow and temperature and single lever operating member. The shower outlet incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted shower mixer with brass body (chrome plated face plate), incorporating a ceramic cartridge headwork ,controlling the flow and temperature with single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted blending thermostatic shower valve (chrome plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge. Both using cube type operating members. The inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow protection. The inlets also incorporate ¾” BSP (M) x 15mm compression (chrome plated) spherical ball valves and EPDM washers incorporating stainless steel mesh strainers. The product is supplied with a chrome plated shower handset, shower hose and riser rail assembly. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic shower valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. Both inlets incorporate approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). The valves are supplied with a variety of shower kits that consist of shower hoses, shower handsets and riser rail assemblies. Model is supplied with a flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Wall mounted thermostatic shower valve (chrome plated brass), incorporating a non-rising spindle headwork controlling the flow and a thermostatic cartridge independently controlling the temperature, both using single lever operating members. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with a chrome plated shower handset, shower hose and riser rail assembly. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valves (chrome plated brass) with non-rising spindle headwork controlling the flow with single lever operating member. The temperature is controlled independently via a thermostatic cartridge with single lever operating member. The inlets for all models incorporate flow regulators and approved check valve cartridges, (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Range of wall mounted, thermostatic blending valves incorporating ceramic disc diverter cartridges. Inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to verify backflow protection. Product also had manual override button. Model VM207X and variants are supplied with variations of dome and single lever operating members. Model VM208X and variants are supplied with varaitions of cube type operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The valve can be supplied with a variation of shower kits that can consist of the following components: handsets, overhead showers, shower hoses, wall outlets, fixed arms, and isolation valves. Maximum working pressure 7 bar. Maximum working temperature 65°C.
Concealed electronic thermostatic shower valve with a plastic body, the flow is controlled via two motorised valves for hot and cold supply. Both inlets incorporate a plastic strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is also supplied with a concealed diverter valves with a plastic body. The flow is controlled to two outlets via solenoid valves. The valve can be supplied with a variation of shower kits that can consist of the following components: handsets, overhead showers, shower hoses, wall outlets, fixed arms, and isolation valves. Maximum working pressure 5.0 bar. Maximum working temperature 65°C.
Electronically controlled thermostatic shower mixing valve with a plastic body. Temperature is controlled via two motorised valves and a thermistor. The product also incorporates a pump and plastic filters on each inlet. The valve can be supplied with a variation of shower kits that can consist of the following components: handsets, overhead showers, shower hoses, wall outlets, fixed arms, exposed elbows and isolation valves. Maximum working pressure 7.0 bar. Maximum working temperature 65°C.
Electronically controlled thermostatic shower mixing valve with a plastic body. Temperature is controlled via two motorised valves and a thermistor. The product also incorporates a pump and plastic filters on each inlet. This product is also supplied with a concealed diverter valves with a plastic body. The flow is controlled to two outlets via solenoid valves. The valve can be supplied with a variation of shower kits that can consist of the following components: handsets, overhead showers, shower hoses, wall outlets, fixed arms, exposed elbows, and isolation valves. Maximum working pressure 5.0 bar. Maximum working temperature 65°C.
Wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a ceramic cartridge headwork controlling the flow and temperature with single lever type operating member. Both inlets are supplied with a stainless-steel strainer. The inlets also incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.
Wall mounted thermostatic shower valve (brass body, matt black finish), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C
Wall mounted thermostatic shower valve (brass body, matt black finish), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with cube type operating member. Temperature is controlled independently via a thermostatic cartridge with a cube type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C.
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted shower valves (chromium plated brass) incorporating self-cancelling diverter for the overhead shower to shower handset. The flow and temperature are controlled by a ceramic cartridge headwork with a single lever operating member. Both models have a fixed overhead shower and model 26023661 also is supplied with a hand shower and hose. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless steel (CF8M) discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and stainless steel (CF8M) discs (not epoxy coated), incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of pressure reducing valves with DZR brass, gunmetal or stainless-steel bodies. Maximum inlet pressure for HP and SP Models = 25.0 bar. Maximum inlet pressure for LP Models = 6.0 bar. Maximum operating temperature 60°C
Normally closed (monostable) or latching (bistable) solenoid valve with a plastic body, EPDM membrane and ‘O’-rings, for insertion into specifically dimensioned bores. The inlet incorporates a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of full bore spherical valves with single lever, lockable lever or butterfly operating members, nickel plate brass bodies and chrome plated, brass ball, PTFE seats and NBR O-rings.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spherical valve (lever operated) with a DZR brass body, brass ball and PTFE seat. The second outlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). There is a test port located between the check valve cartridges. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass bodies, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass bodies, , EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of magnetic, electrolytic or combined magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
‘FLOGUL® 656 Bleu 5005’. Factory applied, blue coloured VOC paint. Apply as per manufacturer’s TDS dated ‘06/04/2022’. Cure for 7 days@20°C. For use with water up to 60°C.
‘R-4401, E-44131, E-4413, E-4414, E-4420, E440001, E441001, E440002, E441002, E-5402, E-5403, E-5404, E540001. E541001, E540002, E540003, E541003 & E440007’. Factory applied, grey-blue coloured enamel coatings. Apply as per manufacturer’s instructions ‘issue 02/2016’ dated 05.10.2016. Cure for 6 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoguard SF156'. Factory applied, grey coloured, two-component solvent-free epoxy coating. In January 2024, 'Apcoguard SF156', factory applied, red coloured, two-component solvent-free epoxy coating was added to the approval. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's Application Guidelines 'APPPG/SF156/001', dated 'Aug-2017'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur 35560 Light grey (10500), Light red (50900) & Cream (20320)'. Factory applied, grey, light red coloured & Cream, two-component epoxy coatings. Each colour can be used as a base or topcoat and as a two-coat system. Mix base and curing agent in a 6.8:2 volume ratio. Apply Light Grey and Light Red as per manufacturer's Application Instructions issued 'November 2019'. Apply Cream as per manufacturer's Product Data Sheet dated 'December 2023'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. Between December 2022 and November 2024, the Light Grey and Light Red were for use with water up to 40°C. Between December 2024 and December 2027, Light Grey and Light Red are for use with water up to 60°C. The Cream coating was added to the approval in May 2025 and is for use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic VE660'. Olive coloured, contact moulded GRP material. For use with water up to 23°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Tecomid NA40 GR30 BK250 HS QW'. 'Tecomid NA40 GR35 BK250 HS QW'. 'Tecomid NA40 GR40 BK250 HS QW'. 'Tecomid NA40 GR45 BK250 HS QW'. 'Tecomid NA40 GR50 BK250 HS QW'. Black coloured, injection moulded, glass fibre reinforced (30% - 50%), PA66 materials. For use with water up to 85°C.
'Sierra PE-100 pipes'. Blue coloured, extruded PE-100 pipes. For use with water up to 65°C.
'Iglidur® UW160 Bearing'. Grey coloured, injection moulded PE bearing. For use with water up to 85°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'UGPM HDPE Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'P600 BL & P301E BL'. Black coloured, extruded polyethylene pipes. For use with water up to 23°C.
'S-Ion PE100 Fittings'. Blue coloured, injection moulded PE100 fittings. For use with water up to 65°C.
'Borsafe ME3440 (black), Borsafe ME3444 (blue) & Borsafe ME3440-W (black)'. PE80 materials suitable for injection moulding and extrusion purposes. For use with water up to 60°C.
'Thermocomp MB006SXP-BK1A994' (black coloured). Injection moulded polypropylene material. For use with water up to 85°C.
'BOSS 79024607'. White coloured, extruded PTFE tape. For use with water up to 85°C.
'EW Gasket Material'. Black coloured EPDM gasket material which is injection moulded and then spliced. Shore hardness 65A. Initial tested in-radius size 3.9mm. In March 2023, the tested in-radius size was increased to 4.4mm. For use with water up to 23°C.
'E65-04BL-G / Black'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 23°C.
'MRP-EN-50, MRP-EN-55, MRP-EN-60, MRP-EN-65, MRP-EN-70, MRP-EN-75 & MRP-EN-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 80. Tested in-radius size 0.88mm. For use with water up to 65°C.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
‘EP70A9OF’. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.06mm For use with water up to 23°C.
'AA6KWZ, AA7KWZ, AA8KWZ and AA9KWZ'. Black coloured, compression moulded EPDM materials with a shore hardness of between 60 & 88. Tested in-radius size 1.0mm. AA6KWZ is for use with water up to 65°C. AA7KWZ, AA8KWZ and AA9KWZ are for use with water up to 23°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Berner Green Paste'. Green coloured, polymer sealing paste. Apply as per manufacturer's Technical Data Sheet '46845(P)', dated 'December 2019'. For use with water up to 85°C.
'KITAN X FV60 HWR'. Black coloured, injection moulded, Polyarylamide material. For use with water up to 85°C.
'RTP 0599 X 145641 BLACK'. Dark grey coloured, injection moulded, SAN material. For use with water up to 50°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 1.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) electronically controlled tap assemblies. The flow and temperature is controlled by a ceramic cartridge headworks with single lever operating members. The flow is also controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The hose inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted taps for cold or premixed water with stainless steel bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor, and the spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and the temperature is controlled via a ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a single check valve assembly (verified by test suitable for backflow protection against Fluid Category 2) and the inlet incorporates a stainless-steel strainer. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a angle valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout has a waterfall outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flushing valves (gunmetal body) which incorporate a screw down stop valve, spherical valve and air gap to drain. Maximum working pressure 10.0 bar. Cold water use only.
Range of single hole, single outlet pull out spray, combination tap assemblies (brass bodies, various finishes – see models) incorporating ceramic cartridge headworks with single lever operating members controlling the hot and cold and a quarter turn ceramic disk headwork with a dome type operating member controlling chilled water supply. The spout outlet incorporates a plastic aerator. The inlet from the tap to the pull-out spray hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc (model SL-T40602W) or a non-rising spindle headwork (models SL-T40502W & SL-T40702W) with lever, cross top or dome type operating members. The spout outlets incorporate a flow straightener. Maximum working pressure 6.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. . Maximum working pressure - 5.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), T-638-series incorporates quarter turn ceramic disc headworks with single lever operating members T-638M series incorporates, non-rising spindle headworks with dome or cross-top operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Max operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener (TR1025 and TR1026 models) or a plastic aerator (all other models). The products are supplied with or without a click type pop-up waste (see model). Maximum operating pressure: MINI models 10.0 bar, all other models 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assembly (various finishes, see models), incorporating ceramic cartridge headworks with single lever operating members. The products incorporate self-cancelling diverters to shower outlets and plastic aerators in the spouts. Not supplied with hose and handset. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome and ‘supersteel’ plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, metal, single outlet (swivel) combination tap assemblies (various finishes), incorporating a ceramic disc headwork controlling the temperature with a single lever operating member and a push on/off button cartridge controlling the flow. The spout outlet incorporates a plastic aerator. Supplied with a lever pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel), combination tap assemblies (brass bodies with various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with single lever, cross-top or dome operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 or 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body-various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets for the V7K20 models incorporate plastic flow straighteners and the V7K35 models incorporate plastic aerators. Models added September 2024 incorporate a single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members (310805) or cross top operating members (771429). The spout outlet incorporates a plastic flow straightener and a combined NBR washer and stainless steel strainer. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, metal, single outlet, fixed combination tap assembly with brass body (chrome plated), incorporating ceramic cartridge headwork with single lever operating member and self cancelling diverter to shower outlet. The shower outlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Three-hole, single outlet (fixed) combination tap assembly (brass body, various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with stainless steel braided PEX lined connecting hoses and a lever operated waste. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of three-hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes). Incorporating quarter turn ceramic disc headworks incorporating single lever, dome, or cross top type operating members (see models) and supplied with stainless steel braided EPDM lined connection hoses. The spout outlet incorporates a plastic aerator. The spout and side valves are connected via stainless steel braided EPDM lined flexible hoses with EPDM washers and O-rings. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, three-hole, combination tap assemblies, (various finishes - see model), comprising of two ceramic cartridge headworks each with a single lever operating member. The product is supplied with stainless steel braided thermoplastic silicone (TPSiV) lined flexible connection hoses and a nylon braided silicone lined flexible hose assembly, which connects to a shower hose (brass double interlocked, PEX lined) and a deck mounted shower handset. Spout not supplied. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of brass compression fittings for use with copper pipes (manufactured to EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘Super Speedfit’ range of plastic pushfit fittings (black, light grey, dark grey, white, natural, and red) for use with John Guest LLDPE tubing (blue, black, natural, green, orange, red, white and yellow). Operating parameters: 5/32”, ¼”, 5/16”, 4mm & 6mm = 16.0 bar cold water & 8.0 bar at 65°C. 3/8” = 10.0 bar cold water & 7.0 bar at 65°C. ½” = 10.0 bar cold water & 6.0 bar at 65°C. 8mm, 12mm & 15mm = 10.0bar cold water & 6.0 ba at 65°C. 10mm = 10.0bar cold water & 7.0 bar at 65°C.
Range of brass or copper capillary solder ring fittings for use with copper pipe. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘Flowflex’ and ‘Lamontite’ ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘Flowflex’ and ‘Lamontite’ ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Primaflow ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of ‘Superseal’ and ‘Speedfit’ push-fit fittings with acetal body’s (black or light grey) and NBR ‘O’ rings. For use with John Guest LLDPE tubing (Speedfit port only) and 316 stainless steel tubing manufactured to EN10088 (Superseal push-fit port only). Pipe inserts must be used for the LLDPE tube sizes 3/8” and ½”. Maximum working pressure: See models below. For cold water use only.
Range of air- or water-cooled commercial ice making machines with flow controlled via solenoid valve. Maximum working pressure 5 Bar
Non-metallic materials and components comply with BS6920 at 35°C
Range of water meters with brass bodies and plastic turbines. The inlet incorporates a plastic filter. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with a stainless-steel bodies. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
‘Wesan WP’ range of water meters with black epoxy coated cast iron bodies, plastic impellers and EPDM ‘O’-rings and lip seal (DN50-65 models) and EPDM ‘O’-rings and gasket + NBR ‘O’-ring (DN80-125 models). Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with (blue epoxy coated) brass bodies and plastic working chamber. The inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of acoustic leak sensors with stainless steel bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of tap outlets with plastic bodies incorporating a filter within the body with a hollow fibre filter membrane The filters are supplied with (and must be used with) a chrome plated brass adapter which incorporates a plastic flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
TP series 200 range of single stage pumps with electrocoated cast iron or bronze bodies, stainless steel impellers and EPDM ‘O’-rings. (TPE models are only available with electrocoated cast iron bodies). The products can incorporate the following shaft seal variations: BQQE (silicon carbide-silicon carbide) & BQBE (Silicon carbide-carbon). The TPE pumps are available with or without a sensor. Maximum working pressure 16.0 bar (TP and TPE40-XXX/2 and TP and TPE40 XXX/2 models). All other models 10.0 bar. Maximum operating temperature: Bronze models are 85°C, cast iron models are cold water use only.
CR(I)(N)(E) ranges of multistage centrifugal pumps incorporating stainless steel impellers, intermediate chamber and outer sleeve. CR(E) versions have cast iron bases and pump heads coated with black cathodic paint. CRI(E) and CRN(E) versions have stainless steel bases and pumpheads. The pumps are available with the following shaft seals HQQ*, HUU*, HUB*, HQB*, where * can be E for EPDM and V for FKM. Maximum working pressures: CR1, 3 or 5 (2-36 stages) Oval flange: 16.0 bar. CR1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange: 25.0 bar CRI/N1, 3 or 5 (2-36 stages) Flexi clamp with oval flange connection: 16.0 bar CR/I/N1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange, PJE, Flexi clamp or Triclamp: 25.0 bar CR10 (1-16 stages) Oval flange or DIN/ANSI/JIS flange: 16.0 bar. CR10 (17-22 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI10 (1-16 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI10 (17-22 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar CRN10 (1-22 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR15 or 20 (1-7 stages) Oval flange: 10.0 bar. CR15 or 20 (1-10 stages) DIN/ANSI/JIS flange: 16.0 bar. CR15 or 20 (11-17 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI15 or 20 (1-7 stages) Flexi clamp with oval flange connection: 10.0 bar CRI15 or 20 (1-10 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI15 or 20 (11-17 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CRN15 or 20 (1-17 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR models: Cold water use only. CRI/CRN models: Cold water use only and from April 2023 99°C.
CR(N)(E) ranges of vertical multistage centrifugal pumps with stainless steel (CRN models) or black polymer coated cast iron bodies (CR models) and a stainless steel impeller. The products are available with or without a sensor. Maximum working pressure: 16.0 bar - CR(N)(E) 32 range with 1-7 stages, CR(N)(E) 45 range with 1-5 stages, CR(N)(E) 64 range with 1-5 stages. 30.0 bar - CR(N)(E) 32 range with 8-14 stages, CR(N)(E) 45 range with 6-11 stages, CR(N)(E) 64 range with 6-8 stages. 33.0 bar - CR(N)(E) 45 range with 12-13 stages. Maximum operating temperature - CR models are cold water use only. CRN models are cold water use only up to February 2nd 2023, and 99°C from February 3rd 2023.
‘UPM4’ range of circulator pumps with either a composite (plastic) or stainless-steel body, plastic impellor and EPDM ‘O’-rings. The 1”-1½” models are supplied with EPDM gaskets for the inlet and outlet. The 2” model has fibre/NBR gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C ((CIL3) plastic body models), 99°C (S/Steel body models).
‘Homebooster’ pump with stainless steel body, plastic impeller and EPDM rubber ‘O’-rings. The product is supplied with two loose brass ¾” captive nut x ½” BSP (M) connectors and fibre gaskets for installation on the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of shower elbows/holders with brass or stainless-steel bodies (various finishes). The elbows incorporate a plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models VOLA 070-XX & VOLA 070R-XX are supplied with a shower hose and handset.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets with plastic bodies. The inlets incorporate a stainless-steel strainer and a built-in flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower heads with plastic bodies (various finishes), incorporating plastic strainer or flow restrictor and EPDM o rings with stainless-steel strainers on the inlets. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with plastic bodies (various finishes), EPDM O-rings and a stainless-steel strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets (ABS bodies - various finishes, see model), incorporating NBR and EPDM ‘O’ rings that incorporate stainless-steel mesh strainers.
Non-metallic materials and components comply with BS6920 at 70°C
Shower kit consisting of a shower handset and shower hose incorporating a riser rail assembly.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower kits, (various finishes - see model), comprising of a shower hose (brass double interlocked, PEX lined) and a shower handset. Maximum operating temperature 60°C.
Range of showers handsets incorporating plastic bodies (chrome plated) Maximum operating temperature 60°C.
Range of Y-strainers with a brass body incorporating a stainless-steel strainer and EPDM ‘O’-rings. For use with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pillar taps (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating member. Spout oultlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc (SL-T40607W) or non-rising spindle headworks (all other models) with various operating members and metal backnuts. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc (SL-T40606W) or non-rising spindle headworks (all other models) with various operating members and metal backnuts. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 6.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
‘TAQ’ range of stainless steel or grey nylon braided (indicated by ACB in model name), EPDM lined flexible hose assemblies, incorporating various end connections. Some of the possible end connections also incorporate EPDM washers, gaskets or ‘O’-rings. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of multi-layer shower hoses with a PVC inner hose, supplied with EPDM ‘O’-rings.
Range of stainless steel indirect (single or twin coil), direct and heat pump unvented hot water storage cylinders. The heat pump models also incorporate a plate heat exchanger and a circulation pump. The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@90.0˚C. The products are supplied with an inlet control group consisting of an adjustable pressure reducing valve, adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 bar, a strainer, am expansion relief valve set at 6.0 bar and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The products are also supplied with an immersion heater, an expansion vessel (12, 19 or 24 litres depending on model) and a tundish. Maximum supply pressure to the inlet control group: 16.0 bar. Maximum working pressure: Secondary circuit: 5.5 Bar. Primary Circuit: 6.0 Bar (All models except for the Direct - DI prefix models). Maximum operating temperature 75°C.
Range of 2, 3 and 4 port brushed chrome DZR brass manifolds incorporating a screw down isolation valve at each port and brass compression adaptors (MFIT100053). Pushfit outlets are for use with copper pipe (manufactured to EN1057), BPB pipe (manufactured to BS EN 7291-2:2010) and BPEX pipe (manufactured to BS EN 7291-3:2010). MANA500552, MANA500553 and MANA500554 models used in conjunction with the MFIT100053 brass compression adaptor on the outlets are for use with BPB pipe (manufactured to BS EN 7291-2:2010) and BPEX pipe (manufactured to BS EN 7291-3:2010). Maximum working pressure 10.0 bar at 82°C and 16.0 bar at 20°C.
Range of automatic air venting valves incorporating epoxy coated, ductile iron bodies and plastic float. Maximum operating pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of automatic air venting valves with brass bodies, stainless steel strainer, plastic float and EPDM ‘O’-rings and gaskets. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of exposed thermostatic shower valves with brass bodies (various finishes) incorporating a half turn ceramic disc headwork controlling the flow between 2 outlets, with the temperature being controlled independently via a thermostatic cartridge both with a single lever operating member. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
A range either concealed or exposed wall mounted thermostatic mixing valves with brass bodies (exposed models are chromium plated). Models CONCEALED007 & CONCEALED008 incorporate ¼ turn ceramic disc headworks and a manual diverter with a shut off. All models incorporate a thermostatic cartridge that controls the temperature. The inlets of all models incorporate stainless steel filters and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (F4017x & F2167x models. All other models 60°C only).
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a quarter turn ceramic disc, half turn ceramic disc or ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a quarter turn ceramic disc, half turn ceramic disc or ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, thermostatic shower valve (chromium plated brass body) incorporating a two-way diverter valve headwork that controls flow between each shower outlet with a cube type operating member. The temperature is controlled independently via a thermostatic cartridge with a cube type operating member with a manual override button. Both inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85°C.
Range of thermostatic shower panels incorporating a single sequential thermostatic control valve with a single lever operating member and flexible riser kit. Each inlet supplied with a servicing valve, EPDM o-ring and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with black lined PVC shower hoses and chrome plated shower handsets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted thermostatic blending valves (various finishes) incorporating a quarter turn ceramic disc headworks with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with manual override and single lever type operating members. The inlets incorporate stainless-steel EPDM strainer washers and approved single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). The products are supplied with shower hose, shower handset and riser rail assembly. Maximum operating pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gear or lever operated wafer, semi lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of combined temperature and pressure relief valves incorporating plastic and DZR brass bodies, and a silicone diaphragm. Compression fittings for use with copper to BS EN 1057. The valves are pre-set at 4.5, 6.0, 7.0 or 10 bar (see models).
Non-metallic materials and components comply with BS6920 at 90°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Wall mounted, flow control valve (either stainless steel or brass body various finishes) incorporating a quarter turn ceramic disc headwork with a single lever operating member. The compression fitting is for use with copper tube complying with BS EN 1057. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of manually operated flow control valves with stainless steel (DN80 – DN150) or epoxy coated ductile iron bodies (DN200 – DN400). Maximum working pressure 10.0 to 40.0 bar, please refer to model. Cold water use only. From April 2023 the products have a maximum operating temperature of 65°C.
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies, carbon steel swing gate encapsulated in EPDM and EPDM valve seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of core manifolds (DZR brass body) incorporating a pressure relief valve (plastic body), with an EPDM diaphragm and ‘O’-rings. For use with copper pipe (manufactured to BS EN 1057). The pressure relief valve is pre-set at 6.0 or 8.0 bar (see models). The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum operating pressure 16.0bar. Cold water use only.
Range of pre-set pressure relief valves (set at 3.0 bar) with plastic bodies and EPDM diaphragm. Maximum working pressure 3.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ‘IBall Vortex’ flow through valves with brass body and EPDM ‘O’-rings incorporating a plastic spherical valve and a drain tap. Maximum working pressure: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with brass bodies and chrome plated brass ball, PTFE washer and EPDM `O` ring and various operating methods. Maximum working pressure 10.0 or 40 bar (see model).
Non-metallic materials and components comply with BS6920 at 85°C
Lever operated spherical flow through valve with brass body and chrome plated brass ball, PTFE seals and EPDM `O` ring. The product incorporates a drain valve. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of spherical valves with a single lever or ‘T’ handle operating member. The products have a DZR brass body and a chrome plated DZR brass ball, except for the models with the ‘-OT’ suffix, models have (nickel-plated brass bodies) and chrome plated brass ball. The products are supplied with various end connections (see model). Maximum working pressures: 15mm to 28mm = 40 Bar 35mm = 25 bar 42mm to 54mm = 16 bar (All models). 42 to 54mm = 10 Bar (4E05, 4E05-OT, 4E06 and 4E06-OT models) Maximum operating temperature 40.0°C
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
AVK Series 21 range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM ‘O’-rings and non-rising spindles. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of gate valves incorporating ductile iron epoxy coted bodies and with EPDM ‘O’-ring seals and discs. The valves are operated via a non-rising spindle with a hand wheel operating member Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only. From Jan 2025 maximum operating temperature 50°C, for models marked "WRAS - 50 DEGREES" on adhesive label on bonnet.
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM gasket and NBR O rings. The valves incorporate a non-rising spindle headwork. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
'WB50 Black Waterborne Pipe Anticorrosive Paint'. Factory applied, black coloured polyacrylate coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEP50 Black Waterborne Epoxy Pipe Anticorrosive Paint'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'3011 Red Epoxy Anticorrosive Coating'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's instructions '004', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5015 Blue Epoxy Anticorrosive Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions '005', revision date '2021.12.12' . Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘E1H8691 ValveClad, E1H8868 ValveClad & E2H6531’. Factory applied, blue coloured epoxy powder coatings (manufactured in UK and France). Apply as per manufacturer’s instructions dated January 2023. Cure for 10 minutes@180°C (metal temperature). E1H8691 ValveClad and E1H8868 ValveClad are for use with water up to 23°C. E2H6531 is for use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 Blue Waterborne Pipe Anti-Corrosive Paint'. Factory applied, blue coloured polyacrylate paint. Apply as per manufacturer's TDS/IFU '001', 'First Edition', dated '2021.12.12'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP-TANK 500 PW'. Factory applied, white coloured (once mixed), two-component, solvent-free epoxy coating. Mix Part A (white liquid) with Part B (dark amber liquid) in a 3:1 volume ratio. Apply as per manufacturer's TDS 'Rev. 06/22'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FLOGUL 645B Bleu 5005'. Factory applied, blue coloured synthetic resin coating. Apply as per manufacturer's Technical Data Sheet, version '26/01/2023'. Cure for 7 days@20°C. For use with water up to 23°C.
'Xypex Concentrate'. Site applied, grey coloured, cementitious coating. Mix 'Xypex Concentrate' with water in a 5:2 ratio and apply as per manufacturer's datasheet 'DAT-CON-UK, REV-06-21'. Cure for 3 days@7°C in damp conditions, following by 18 days@7°C. Please note that 1 day cure = 24 hours. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CPT CML Variation No.2 cementitious mortar’ for use with ‘Conplast RP264 Admixture'. Site applied, grey coloured (once mixed) cementitious mortar and admixture. 'CPT CML Variation No.2 cementitious mortar’ comprises of cement, sand and Microsilica. Mix cement and sand dry in a 1:1.1 mass ratio. Add the microsilica in a 1:0.05 mass ratio with the cement content. Add water in a cement/water mass ratio of 1:0.32. Add the admixture in an admixture/ cement ratio of 8ml:1000g. Mix rigorously until an even consistency is achieved and apply as per manufacturer’s instructions reference ‘2328’, dated 13/01/2023. Cure for 28 days@ between 10°C and 35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquastore'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquasystem'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Aquatank'. Grey coloured, GRP panels manufactured by hydraulic press. For use with water up to 60°C.
'Atlac 430'. Yellow coloured, vinyl ester resin material manufactured by filament winding. For use with water up to 60°C.
'SL6015 Silicone Hose'. White coloured (translucent), extruded silicone hose. Shore hardness 60. Tested in-radius size 0.5mm. For use with water up to 85°C.
'SABFUSE'. Black coloured, injection moulded polyethylene fittings. For use with water up to 60°C.
'National Brand PE Pipe'. Blue coloured, extruded PE100 pipe. For use with water up to 65°C.
'EPPI-PE'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'UPIPIPE'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'SABIC® Vestolen A 5061R 10000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
‘SABIC® Vestolen A 6060 R 10000 (black)’. Black coloured, extruded HDPE material. For use with water up to 23°C.
'JP Water Zone PP Saddle Fittings'. Blue coloured, injection moulded polypropylene saddle fittings. For use with water up to 65°C.
'HW-EPDM'. Black coloured, compression moulded EPDM sheet materials. Shore hardness 50, 60, 70 and 80. Tested in-radius size 1.0mm. The 50 shore hardness material is for use with water up to 65°C. The 60, 70 & 80 shore hardness materials are for use with water up to 60°C.
‘51M5577, 51M6077, 51M6577, 51M7077, 51M7577, 51M8077, 51M8577’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Spray SLC STD Inlay 24' & 'Spray SLC STD Inlay 16 Low'. Grey coloured, injection moulded, liquid silicone rubber components. Shore hardness 70. Tested in-radius size 0.44mm. For use with water up to 70°C.
Range of deck mounted taps for cold or premixed water (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet hoses have stainless steel strainers and incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose and a manual lever for controlling the temperature. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel for models 236303 & 236404 only or chromium plated brass for all others). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and the products are supplied with stainless steel braided PEX line connection hoses. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of side and bottom entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of high and low level BS EN 14055 (2018) WC cisterns incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush or mono flush syphon for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres.. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Range of spring loaded resilient trim check valve cartridges with acetal body and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tundishes with plastic bodies. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of one piece water storage cisterns with a screened breather and over flow. Model 46714 iBoost+200 has a rectangular weir overflow Model 46712 iBoost+200 has a circular overflow Cold water only.
Range of single hole, single outlet combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating member. Product supplied with permanently open/click type waste outlet. Spout outlet incorporates a plastic aerator, fitting is supplied with a hose and bidette handset Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of ceramic cartridge headwork with plastic bodied and EPDM ‘O’ rings for insertion into specifically dimensioned bores. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of quarter turn ceramic disc and ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic cartridges with brass or plastic bodies (see model) incorporating a stainless-steel strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar. Temperature: 75°C – GR-FX-X05S, GR-FX-01S, GR-FX-13T & GR-FX-X08. 65°C - GR-FX-04S & GR-FX-02TF.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating ceramic cartridge headworks with single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers. Models ZA1147(ZA1147-G, ZA1147-S) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet is a pull-out spray type. The spout inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow prevention. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pull-down hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet combination tap assembly with brass bodies (chrome plated), incorporating ceramic cartridge headwork and single lever operating members. Spouts incorporate a plastic aerator. Model 3326530L is supplied with a lever-operated pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. Maximum working pressure - 5.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet fixed combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever (31- prefix models) or dome type (04- prefix models) operating member. The spout outlet incorporates a plastic flow straightener (31- prefix models) or a plastic aerator (04- prefix models). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, fixed combination tap assembly (brass body in various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. Maximum working pressure - 10.0 Bar Model Braye 94015 Maximum working pressure - 5.0 Bar Model 85781 Pentle Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (model M101086) or 85°C (all other models).
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with lever type pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature (See models)
Range of single hole, single outlet fixed combination tap assemblies, (chrome plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet incorporates a plastic aerator. Models (63301, 63501, 63303, 63503, 63305 & 63505 are supplied with lever operated pop-up waste) Maximum working pressure 5 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 Bar Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C Models added October 2024: Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartride headworks and single lever operating member.. Spout outlet incorporates a plastic aerator and product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating member. Spout outlet incorporates a plastic aerator and products are also supplied with lever operated pop-up wastes. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, chrome or black finish) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a spring-loaded pull-down hose incorporating a spray handset with trigger mechanism that controls the spray. The spray handset incorporates a plastic aerator at the outlet. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel), combination tap assemblies (brass bodies with various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with single lever, cross-top or dome operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 or 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, swivel, combination tap assemblies in chromium plated brass. The models incorporate a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headwork with single lever operating members controls the flow of hot and cold water. A quarter turn ceramic disc headwork with single lever operating member which incorporates a manual override button, controls the flow of near-boiling water The spout outlets incorporate a plastic areator. Maximum working pressure: hot and cold water = 8.0 bar. Maximum operating temperature hot and cold water circuit is 65°C. Maximum operating temperature of near-boiling water circuit 100°C
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a stainless steel strainer and a plastic flow straightener.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body, various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 6 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. Products are supplied with a shower hose and handset and plastic or metal back nuts. Maximum working pressure 6.0 Bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The shower outlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two hole, single outlet, wall mounted combination tap assembly with brass bodies (various finishes), incorporating ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to the shower outlet. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic disc headwork with dome, push on/off type operating member. Inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating non-rising spindle headworks with cross-top operating members (SL-KT009W) and dome type operating members (SL-KT008W). Model (SL-KT010W) incorporates a quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 6.0 Bar Maximum operating temperature 65.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies, (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with various operating members and lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks. The spout inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure: 5.0 Bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
A deck mounted, three-hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks with cross top operating members. The product is also supplied with stainless steel braided, EPDM lined flexible connecting hose assemblies, intended for use between side body valves and spout. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of four-hole, single outlet combination tap assemblies with various finishes (see models) Incorporating a ceramic cartridge headwork controlling the flow to the shower handset and quarter turn ceramic headworks controlling flow to the spout outlet, all with single lever operating members. The product is supplied with a shower hose and handset, the handset incorporates a single check valve on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, swivel, bath mixers (brass or stainless-steel bodies - variety of finishes (see models), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products also incorporate self-cancelling diverters to a shower handset. The diverter outlets incorporate an approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, two single outlets (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating ceramic cartridge headwork, single lever operating member controlling both flow and temperature to the spout and spring-loaded pull-down hose. The pull-down hose incorporates a hand spray with a self-closing trigger mechanism. The spout incorporates a ceramic disc headwork controlling the flow with a single lever operating member. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of combined bath filler and overflow waste assemblies incorporating a cable operated pop-up waste. The outlet incorporates a plastic flow straightener. Maximum operating temperature 60°C.
Wall mounted tap assembly (chromium plated brass) incorporating a ¼ turn ceramic disc controlling the flow and a plastic aerator in the spout outlet. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted or floor standing spout outlets (fixed or swivel - see model, chromium plated brass). All models incorporate a plastic flow straightener, except for the 93-6106-01 model which has a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted spout outlets (fixed or swivel - see model, chromium plated brass) incorporating a plastic flow straightener. The products are supplied with metal backnuts.
Non-metallic materials and components comply with BS6920 at 60°C
Range of swivel spout outlets with brass or stainless-steel bodies supplied in various finishes (see model). The products also incorporate a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of longitudinal (EFW) welded stainless steel (Grade 304/304L & 316/316L) pipes. Maximum working pressures: 1¼” sch 10: below ground = 55.0 bar. Above ground = 74.0 bar. 1½” sch 10: below ground = 48.0 bar. Above ground = 64.0 bar. 2” sch 10: below ground = 38.5 bar. Above ground = 51.0 bar. 2½” sch 10: below ground = 34.5 bar. Above ground = 46.0 bar. 3” sch 10: below ground = 28.0 bar. Above ground = 38.0 bar. 4” sch 10: below ground = 22.0 bar. Above ground = 29.0 bar. 5” sch 10: below ground = 19.5 bar. Above ground = 26.0 bar. 6” sch 10: below ground = 16.0 bar. Above ground = 22.0 bar. 8” sch 10: below ground = 14.0 bar. Above ground = 18.0 bar. ½” sch 40 & ¾” sch 40: below ground = 60.0 bar. Above ground = 80.0 bar. 1” sch 40: below ground = 30.0 bar. Above ground = 40.0 bar. 1¼” sch 40 & 1½” sch 40: below ground = 60.0 bar. Above ground = 80.0 bar. 2” sch 40: below ground = 54.5 bar. Above ground = 72.0 bar. 2½” sch 40: below ground = 60.0 bar. Above ground = 80.0 bar. 3” sch 40: below ground = 52.0 bar. Above ground = 69.0 bar. 4” sch 40: below ground = 44 bar. Above ground = 58.0 bar 5” sch 40: below ground = 38.5 bar. Above ground = 51.0 bar. 6” sch 40: below ground = 35.0 bar. Above ground = 46.0 bar. 8” sch 40: below ground = 31.0 bar. Above ground = 41.0 bar. Maximum operating temperature 100°C.
“Super Speedfit” range of push-fit fittings with polypropylene bodies and EPDM or NBR ‘O’-rings (NC2301 model only) for use with John Guest LLDPE tubing (blue, black, natural, green, orange, red, white and yellow). Maximum working pressure and maximum operating temperature: 10bar @20°C, 4 bar @60°C.
CB Ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
CB ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Ranges of brass & chromium plated brass, nickel plated brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of press-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with SS316L pipes. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘H5000’ range of helical rotor, bulk water meters with blue epoxy coated cast iron bodies and nitrile `O` rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
‘V210’ range of volumetric water meters with brass bodies and NBR ‘O’-rings. Available with a mechanical or electronic register. Maximum working pressure 16.0 bar. Cold water use only.
‘V200’ range of rotating piston (semi positive) volumetric in-line water meters with brass bodies, EPDM ‘O’-rings and seal (DN40 model only), NBR ‘O’-rings (all other models) and seal (DN15 36RPL model only). Available with a mechanical or electronic register. Maximum working pressure 16.0 bar. Cold water use only.
‘V110’ range in-line volumetric water meters with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only.
Range of inline water meters with brass (16.0 bar models) or bronze (20 bar model) bodies and plastic turbines. Model FL040FM300 has a plastic filter. All models excluding FL150KP450_00_UK: Maximum working pressure 16.0 bar Model FL150KP450_00_UK only: Maximum working pressure 20.0 bar. Cold water use only.
Range of ultrasonic water meters with plastic (PL) or brass (BR) bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating Temperature 50 C
Range of ultrasonic water meters with brass bodies and EPDM ‘O’-rings and plastic strainer. The products incorporate a motor operated isolation valve. Maximum working pressure 16.0 bar. Maximum operating temperatures: LXC-15 model: 65°C. LXC-20 model and models added May 2025: 85°C
Range of water meters with brass bodies and plastic turbines. The inlet incorporates a plastic filter. Maximum working pressure 16.0 Bar. Maximum operating temperature 50°C
Range of in-line plastic flow restrictors housed within black or grey glass fibre reinforced nylon bodies. Maximum working pressure 16.0
Non-metallic materials and components comply with BS6920 at 85°C
Range of waste and overflow assemblies for bathtub with intergrated water inlet with a plastic body. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of water pressure booster sets with a cold water storage cistern and booster pump. All models incorporate a non-return valve, not suitable for backflow protection. These models have an AG air gap suitable for fluid category 3 protection. Maximum working pressure 6.0 bar. Cold water use only.
Range of water pressure booster sets with a cold water storage cistern and booster pump. All models incorporate a non-return valve, not suitable for backflow protection. These models have an AB air gap suitable for fluid category 5 protection. Maximum working pressure 6.0 bar. Cold water use only.
Range of vertical multistage pumps with stainless-steel bodies, stainless-steel impellers, shaft and outer sleeve. Maximum working pressures: T (oval flange): 16.0 bar. V (Victaullic & grooved), C (clamp flanges) & F (round flange) versions: 26.0 bar. Maximum operating temperature 100°C.
Range of horizontal self-priming multistage pumps with stainless steel bodies, stainless steel impellers, shaft and outer sleeve. Maximum working pressure 10.0 Bar Maximum operating temperatures: FGH Three phase models 85°C, FGH Single phase models 55.0°C
Range of shower handsets and shower heads with plastic bodies (chrome plated, except for the DS1200W and DS3200W models which are white) and NBR gaskets.
Non-metallic materials and components comply with BS6920 at 65°C
A range of shower kits consisting of a shower handset, shower hose and riser rail. Open outlet use only
Range of shower handsets with plastic bodies (various finishes). The inlet of the 24120xx0, 24101xx0, 24111xx0, 24110xx0 and 24100xx0 models incorporates a stainless-steel strainer. From November 2023 they can also incorporate a plastic strainer. The inlet of the 26077210 model added November 2023 incorporates a plastic strainer. The inlets of the 24101xx0, 24111xx0, 24121xx0 and 26077210 models also incorporate a plastic flow regulator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Description Overhead shower outlet with brass body (chrome plated) and EPDM ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with chromium plated brass bodies. The inlets incorporate a stainless steel strainer. The 26 578 xxx model also incorporates a flow regulator.
Non-metallic materials and components comply with BS6920 at 70°C
Range of shower handsets with plastic or brass (364 models only) bodies in various finishes (see models).
Non-metallic materials and components comply with BS6920 at 70°C
Range of kits comprising of a shower handset, shower hose and riser rail (various finishes - see models). The shower hose incorporates an EPDM washer and stainless-steel strainer Maximum operating temperature 60°C.
Range of shower heads with brass bodies (various finishes) incorporating EPDM washers with built in strainers. Some models also incorporate flow regulators.
Non-metallic materials and components comply with BS6920 at 85°C
Drain cock with a plastic body. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 75°C
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal back nuts Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (Models 152101, 152102, 179401 &179402) or a plastic aerator (Models 130401 & 130402). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C for all models except 179401 & 179402 which are 85°C
A self-closing tap with a chromium plated brass body with spring loaded headwork and dome type operating members. The spout outlets incorporate a metal spray plate and the products are supplied with metal back nuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of metal double interlocked (PVC or PEX lined), PVC spiral or PVC flat shower hoses.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel braided PEX lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of interlocked shower hoses with EPDM seals and various finishes.
Non-metallic materials and components comply with BS6920 at 70°C
Range of stainless steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel indirect unvented hot water storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve (7.0 bar and 90°C). The product is fitted with a safety kit which comprises of a manifold, check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) strainer, an expansion relief valve set at 6.0 bar and a pressure reducing valve set at 3.0 bar. A tundish and expansion vessel also comes supplied. Maximum working pressure: Secondary circuit: 5.5 Bar Primary circuit: 3.0 Bar Solar circuit: 3.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided. Maximum working pressures: Primary: 6.0 bar Secondary: 5.5 bar
Non-metallic materials and components comply with BS6920 at 85°C
Air vent valve with a plastic body and plastic float. Maximum working pressure 16.0 bar. Cold water use only.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Wall mounted, exposed, manual shower blending valve with a brass body (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The product also incorporates a self-cancelling diverter valve which diverts the flow between an overhead shower or shower handset. The product is supplied with a shower hose, handset, overhead shower and a shower rail. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted shower blending valves (chromium plated brass). Flow is controlled by a quarter turn ceramic disc headwork and also diverts between overhead shower and hand shower with single lever operating member. The temperature is independently controlled via a thermostatic cartridge with single lever operating member that incorporates a manual override. Inlets incorporate stainless steel strainers and an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower handset, shower hose and overhead shower. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Wall mounted, bar type thermostatic blending valves with brass bodies (various finishes see models) incorporating a quarter turn ceramic disc for diverting between shower handset and overhead shower and a thermostatic cartridge controlling the temperature with a manual override button, both with dome type operating members. The product is supplied with an overhead shower head, shower hose and handset. Each inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed, wall mounted thermostatic blending valves (DZR brass body) with a variety of face plate finishes (see models). The products incorporate a ¼ turn ceramic disc headwork to control the flow with a dome operating member. The temperature is controlled independently via a thermostatic cartridge with a dome operating member incorporating a manual override. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted bar type thermostatic shower mixers (brass bodies available with a variety of finishes) incorporating a half turn ceramic disc headwork controlling the flow with a dome type operating member and a manual diverter to shower outlet. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that also incorporates a manual override button. Both inlets incorporate a single check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork, controlling and diverting the flow between overhead shower and handset, with dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate stainless steel strainer and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection Maximum working pressure 10.0 bar. Non-metallic materials and components comply with BS6920 at 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Wall mounted, bar type, thermostatic shower blending valves with brass bodies (various finishes - see model), incorporating a 2-way ceramic disc diverter headwork with a dome type operating member controlling the flow between each shower outlet. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. The product is supplied with an overhead shower, shower hose and handset. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Series of wall mounted, thermostatic mixer valve with brass bodies, diverter headwork that controls flow between one, two or three outlets (see model) with various type of operating member. The temperature is controlled independently via a thermostatic cartridge operating member with a manual override button. Inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 55°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and stainless-steel disc, incorporating EPDM seats. Models DN200, 250, 300, 350 and 400 have a hand wheel operating member. DN50, 65, 80, 100, 125 and 150 have lever operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and EPDM rubber seat. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of wafer and lugged type butterfly valves with ductile iron bodies, blue epoxy coated with stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and EPDM rubber seat. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of pressure reducing valves with gunmetal or stainless steel bodies. Max pressure 16 or 25 bar (See models for details).
Non-metallic materials and components comply with BS6920 at 60°C
Range of pressure reducing valves incorporating chromium plated DZR brass bodies. Some models are supplied with a pressure gauge. Maximum operating temperature 85°C. Please refer to model for maximum inlet pressures and outlet pressures.
Non-metallic materials and components comply with BS6920 at 85°C
Range of solenoid valves with a brass body and an EPDM gasket and ‘O’-ring. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Latching solenoid valves with a plastic body and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of lever operated spherical valves with DZR brass (286W range) or nickel plated brass (289 range) bodies, chromium plated brass ball, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar (286W range), 40.0 bar (289 range). Maximum operating temperature 85°C (286W range), 99°C (289 range).
Range of isolation valves with nickel plated brass bodies, chrome plated brass balls and EPDM O-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies, chrome plated brass balls and EPDM O-rings. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies, chome plated brass balls and EPDM O-rings. Connection to be used with copper pipe EN1057. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of in-line spherical valves with brass bodies, chromium plated brass ball, NBR rubber ‘O’-rings and single lever operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a single lever or ‘T’ handle operating member. The products have a DZR brass body and a chrome plated DZR brass ball, except for the models with the ‘-OT’ suffix, models have (nickel-plated brass bodies) and chrome plated brass ball. The products are supplied with various end connections (see model). Maximum working pressures: 15mm to 28mm = 40 Bar 35mm = 25 bar 42mm to 54mm = 16 bar (All models). 42 to 54mm = 10 Bar (4E05, 4E05-OT, 4E06 and 4E06-OT models) Maximum operating temperature 40.0°C
Range of spherical valves with brass bodies (nickel plated) and brass (chromium plated) balls, PTFE seats and NBR o-rings. Maximum working pressure: ½” to 1” = 40.0 bar, 1¼” to 2” = 25.0 bar. Cold water use only.
Range of spherical valves (shut-off, stop and servicing valves) with either acetal or POM (from 20th December 2023) bodies and a lever type or screwdriver operated operating member. For use with John Guest LLDPE pipe. Maximum working pressure: 10.0 Bar @20°C and 7 Bar @65°C. Non-metallic materials and components comply with BS6920 at 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM gasket and NBR O rings. The valves incorporate a non-rising spindle headwork. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM and EPDM gaskets. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stop valves with either DZR brass, brass, bronze or chrome plated bodies with T-type or lockshield (LS) operating members. Compression models are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
Range of thermostatic circulation valves with gunmetal bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of combination valves consisting of an in-line adjustable pressure reducing valve (between 1.5 and 6.0 bar) and a pressure relief valve, with DZR Brass bodies, EPDM `O`-rings and an EPDM diaphragm. CWIC110004 model - Pressure reducing valve pre-set at 3.5 bar and pressure relief valve set at 6.0 bar. CWIC200055 model - Pressure reducing valve pre-set at 3.0 bar and pressure relief valve set at 4.5 bar. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum supply pressure 16.0 bar. Outlet pressure range 1.5 bar to 6.0 bar (both models). Maximum operating temperature 20°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Activflo range of water conditioners with stainless steel bodies. Models with compression connections are for use with copper pipe (manufactured to BS EN 10 57), stainless steel pipe (BS EN 10312:2002), polybutylene (BS 7291-2) or PE-X pipe (BS7291-3). Maximum working pressure 16 bar. Maximum operating temperature 99°C
Range of UV water treatment units with stainless steel bodies and quartz sleeves. Maximum operating pressure 8.6 bar. Cold water use only.
Duplex (Twin Tank) Non-Electric Water Softener. Maximum working pressure 8.3 Bar Cold water use only.
'KOCETAL GF305'. Off-white coloured, injection moulded POM material. For use with water up to 65°C.
'ABS-EASO727B'. Black coloured, injection moulded ABS material. For use with water up to 65°C.
'B96'. White coloured ceramic tube manufactured by isostatic pressing. For use with water up to 85°C.
'BFSC RIZHAO S&M&B DN 22'. Factory applied, grey coloured Blast Furnace Slag Cement Mortar Lining. Mix cement and sand in a weight ratio of 1:2.2. Mix this with water in a 0.46:1 weight ratio. Apply as per manufacturer's TDS '1008', dated '20221008'. Cure for 9 hours at 60°C & 95% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JHSW-8604 Pipeline Heavy Duty Anti-Corrosion Polyurethane Coating'. Factory applied, two-component, pale yellow coloured polyurethane coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's Product Information, issue date '6/1/2022'. Cure for 1 minute@25°C and then 7 days @23. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FP60 Dark Blue'. Factory applied, dark blue coloured epoxy powder coating. Mix and apply as per manufacturer's TDS 'FP60/Rev:3' October 2020. Cure for 10 minutes@160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YHGuard8680 Primer & YHChlor6200 Topcoat'. Factory applied, blue coloured (once applied), coating system comprising of an epoxy primer and polyethylene topcoat. 'YHGuard8680 Primer’ comprises of a binder and hardener to be mixed in a 30:2.5 weight ratio before being applied as per manufacturer’s data sheet ‘8680 20220601’. Cure for 12 hours@25°C. Apply ‘YHChlor6200 Topcoat' as per manufacturer’s data sheet ‘6200 20220601’. Cure for 5 hours hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPL Gold Portland Slag Cement'. Grey coloured, factory applied Portland Slag cement. Mix cement, sand & water in a 1:1.4:0.35 mass ratio. Apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours@27°C, 70% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's product information dated 'August 16,2022'. Cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Koro-HD'. Green coloured, NBR/fibre gasket material manufactured by calendering. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'SYL-8668'. White coloured (opaque) grease. For use with water up to 70°C.
'G. BESLUX BESSIL 6001'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'LHS001P'. Off-white (translucent), extruded PEX hose. For use with water up to 60°C.
'Jingtong HDPE Pipe'. Black coloured (with blue external lines), extruded HDPE pipes. For use with water up to 65°C.
'Jingtong HDPE Fitting'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'Jain HDPE (PE 100) Blue Fittings). Blue coloured HDPE fittings manufactured by injection moulding or extrusion. For use with water up to 65°C.
'Borealis HB601WG'. Clear, injection moulded polypropylene material. For use with water up to 85°C.
‘3M™ Dyneon™ Fluoroplastic ET 6235Z’. Natural (translucent, white coloured), compression moulded ETFE material. For use with water up to 85°C
3M™ Dyneon™ Fluoroplastic grades - FEP 6301Z, FEP 6303Z, FEP 6307Z, FEP 6322Z and FEP 6322HTZ. Natural coloured FEP materials manufactured by melt-processing. For use with water up to 85°C
3M™ Dyneon™ Fluoroplastic grades PFA 6502NZ, PFA 6502TZ, PFA 6505TZ, PFA 6515NZ, PFA 6515TZ, and PFA 6525TZ. White coloured (natural), transfer moulded PFA material. For use with water up to 85°C.
3M™ Dyneon™ TF 1620, TF 1641, TF 1645, TF 1702, TF 1750, TFM 1600, TFM 1635, TFM 1700, TFM 1705, TF 4103K, TF 4105K, and TFM 4105K. White coloured, pressed+sintered PTFE materials. 3M™ Dyneon™ TF 2021Z, TF 2025Z, TF 2029Z, TF 2035Z, TF 2053Z, TF 2071Z, TF 2072Z, TF 2073Z, TFM 2001Z, TFM 2033Z and TFM 2070Z. White coloured, extruded PTFE materials. 3M™ Dyneon™ TF 4215 & TF 4303. Black coloured, pressed+sintered PTFE materials. For use with water up to 85°C.
'National Plastic Sharjah-LF PVC Pipe' & 'National Plastic Al Ain, Abu Dhabi-LF PVC Pipe'. Grey coloured, extruded PVC pipes. For use with water up to 60°C.
‘DEWALT PV60-PRO’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1, version 16/01/2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 70.10-02 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
‘07096-80 gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 80. Tested in-radius size between 0.9mm & 1.75mm. For use with water up to 85°C.
'51616 – E40, 51616 – E50, 51616 – E60, 51616 – E70 & 51616 – E80'. Black coloured, compression moulded EPDM materials. Shore hardness between 40 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'NBR 70.10-17 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'kSil PL60 Translucent'. Off-white coloured (translucent), silicone rubber material which is extruded onto the calendar. Shore hardness 60. Tested in-radius size 1.05mm. For use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. Spout outlet incorporates plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (chrome plated), The flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. Spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. There is no temperature control or operating member for these products. The spout outlet incorporates a plastic aerator. The products supplied with a plastic flow regulator. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. There is no temperature control or operating member for these products. The spout outlet incorporates a plastic aerator. The products supplied with a plastic flow regulator. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of wall mounted single-hole, single outlet, fixed electronically controlled combination tap assemblies (chrome plated brass), incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of side and bottom entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless-steel spring and EPDM ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 16 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted, electrically heated catering water boilers with inlet supply controlled via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Range of boiling water dispensers incorporating plastic (3-7.5 litre models) or stainless steel (10-40 litre models) cisterns with silicone ‘O’-rings and seals. The flow to the internal reservoir is controlled via a float valve. The internal reservoir incorporates an overflow which acts a vent. The inlet incorporates a plastic filter. Water is dispensed using either a lever or push button (PLUS models only) operated self-closing tap. Maximum working pressure 5.0 bar. Maximum operating temperature 98°C. Cold supply only.
Range of thermostatic cartridges with a brass housing, stainless-steel filters and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole or two-hole pre-rinse taps (chromium plated brass bodies) which have either a single outlet or two outlets. The flow is controlled by rising spindle headworks with single lever operating members and the spout outlet incorporates a plastic flow straightener. Model 89001MN-2 is a single hole tap with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98001-1, 98001-1-01, 98001MN-1, 98001MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-2, 98007MN-2-01, 98007-2 & 98007-2-01 are two-hole taps with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-1 & 98007MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members on models (295385, 295409, 295412,). Model (295316) incorporates quarter turn ceramic disc headworks with cross-top operating members. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. Model (295316) can also be supplied with a lever operated pop-up waste. Maximum working pressure - 10.0 Bar (295316) Maximum working pressure - 5.0 Bar (295385, 295409, 295412) Maximum operating temperature 65.0°C
Single hole, single outlet (fixed) combination tap assemblies (brass body- various finishes) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 193838EX,193838EX MBK1, 163838EX & 163838EX MBK1 is only supplied with an aerator) . The product is supplied with a click type waste (verified by test). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated bodies), incorporating ceramic cartridge headworks with single lever operating members. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Single-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headworks and single lever operating member. Products are supplied with lever operated pop-up wastes and spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) with a ceramic cartridge headwork with a single lever operating member The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure (see models)
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies -various finishes), incorporating ceramic cartridge headworks and single lever operating members. The Spout outlet incorporates a plastic aerator. Some models are supplied with a pop-up waste (see list). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single-outlet (swivel) combination tap assemblies, incorporating a ceramic cartridge headworks with a single lever operating member. A quatrer turn ceramic disc headwork with spring loaded return to the closed position controls flow of the boiling water outlet supply using single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar on the hot and cold supply, 3.0 bar on the boiling water supply. Maximum operating temperature 65°C on the hot and cold supply, 99°C on the boiling water supply.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with under counter boiling water unit (vented via the spout outlet) and in-line water filter (on instantaneous hot water supply only). Flow is controlled by a ceramic cartridge headwork with a single lever operating member. Instantaneous hot water is controlled by a self-closing quarter turn ceramic disc headwork with a single lever operating member. The product is supplied with loose 3/8” x 15mm reducers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 98°C.
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Edition 11’ range of wall mounted, concealed, two hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Model T740005 incorporates ceramic cartridge headwoks. All other models incorporate quarter turn ceramic disc headworks with single lever operating members. Spout outlets incorporate plastic flow straighteners except T8705 with is open. All products are supplied with metal back nuts. T7505M, T8705, T8805, T7115 and T749005 maximum working pressure 5.0 bar, Maximum operating temperature 60°C. T739005 maximum working pressure 16 bar max operating temperature 65°C. T740005 maximum working pressure 10 bar max operating temperature 65°C.
Range of two-hole, single outlet combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener The product is supplied with plastic backnuts. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see models), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. The product incorporates brass backnuts. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. Operating members not supplied. Maximum working pressure 5.0 Bar temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with dome type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two-hole, single outlet fixed combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with, shower hose, handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of two-hole, single outlet, wall mounted combination tap assemblies with (brass body - various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to the shower outlet. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic disc headwork which controls flow and diverts flow between either bath or overhead shower mode with a single lever operating member. The temperature is controlled by a thermostatic cartridge and dome operating member with a manual override. Also incorporates a self-cancelling diverter for spout to the shower handset outlet. The spout outlet incorporates a plastic aerator. The shower outlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Products are supplied with a shower hoses and handsets. Maximum working pressure: 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout incorporates and a self-cancelling diverter to the shower outlet and plastic aerators. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow prevention. This product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Two hole, single outlet (fixed) combination tap assembly (chrome plated brass body), Incorporating non-rising spindle headworks with dome type top operating members. The product incorporates a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Three hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of combined bath fillers and overflow waste assemblies (plated brass covers and plastic hoses) with pop-up wastes. Maximum operating temperature 65ºC. Open outlet use only.
Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Mingshi stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
“TH Instantor” range of brass press fittings and PEX-AL-PEX multi-layered pipe (TH press profile). Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘Unidelta’ brass compression fittings for use with ‘Unidelta UniTerm’ PEX pipe. Maximum working pressure 8.0 bar @ 85°C, 20.0 bar @cold water use.
Range of solder ring brass fittings for use with copper tube (manufactured to EN 1057) with EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of plastic push-fit fittings (available in black, white and grey) and a manifold (available in grey only) with EPDM or NBR ‘O’-rings. For use with copper pipe (manufactured to EN1057), PE-X pipe (manufactured to BS7291-3:2010) & PB pipe (BS EN 21003-2:2008). Maximum working pressure: 12.5 bar @ 20°C (Cold water use only). From September 2023 the products are suitable for 8.0 bar @ 65°C.
Range of end feed brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed brass fittings for use with copper tube (manufactured to EN 1057). Incorporates an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. The HLDPMFWT and HLDPMFZT models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of WC pressure flushing valves with a time flow direct flush valve controlling the flow. The valves are operated via a push-button assembly. The valve also incorporates a lever operated isolation valve. Maximum working pressure - 5 Bar Cold water use only.
Hydraulic block incorporating a stainless steel and copper brazed plate heat exchanger, plastic fittings and adaptors, recirculation pump and a flow adjustment valve. Maximum operating temperature: Central Heating Circuit: 90°C, Direct Hot Water Circuit: 65°C. Maximum working pressure: Central Heating Circuit: 2.5 bar, Direct Hot Water Circuit: 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of flow and temperature sensors with gunmetal bodies and EPDM ‘O’-rings Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of in-line ultrasonic water meters with DZR brass bodies. The following sizes only include a plastic strainer, DN15 - DN32 sizes (incorporated), DN40 size (optional). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Ultrasonic water meter with a brass body. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Water meter housing with DZR brass body, NBR ‘O’-rings and incorporates a spherical valve. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Water meter manifold with a DZR brass body, NBR ‘O’-rings and incorporates a spherical valve. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of single or manifold below ground meter boxes. The boxes incorporate a concentric water meter manifold and a servicing valve on each connection. CV models incorporate an approved single check valve cartridge and the DCV model incorporates two approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The pushfit inlet and outlet connections are supplied with pipe inserts and are for use with MDPE pipe (manufactured to EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Talbot Modular Manifold System with and without concentric water meter connections with plastic bodies incorporating screw down stopvalves. Maximum working pressure 16 bar. Cold water use only.
KHS range of dynamic flow distributors (gun metal bodies) with spherical valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of differential pressure switches with brass or stainless steel (N suffix models) bodies. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Pull-out hose assembly consisting of a chromium plated brass 45° elbow connector, a chromium plated brass HDPE lined shower hose and a nylon braided HDPE lined connecting hose. Maximum operating temperature 65°C.
Range of booster pumps with plastic bodies and impellers, stainless steel shafts, brass manifolds, NBR ‘O’-rings and EPDM seals. The product incorporates a pressure vessel. The outlet(s) incorporate(s) an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The inlet hose(s) supplied with this product incorporate(s) an isolation valve. Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.
Range of cold water supply booster sets, consisting of between 2 & 4 pumps, modular stainless steel manifold system, servicing valve, non-return valve (not suitable for backflow protection) and an expansion vessel. Maximum working pressure 10.0 bar or 16.0 bar (identified on adhesive label on expansion vessel) Cold water use only.
Range of multistage pumps (VL, VLE and CL series) and submersible pumps (VN, VNE CN, ES and CS series) with stainless steel bodies and impellers and NBR gaskets and ‘O’-rings. Maximum working pressure 15.0 bar (VL, VLE and CL series pumps only).
Ceiling mounted shower outlet with black plastic body incorporating EPDM ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 65°C
Range of shower hansets with plastic bodies (various finishes). Inlet incorporates a strainer and flow regulator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of plastic bodied shower outlets with chromium or titanium plated finish. The inlet of the overhead showers incorporates a combined EPDM washer and stainless steel strainer.
Non-metallic materials and components comply with BS6920 at 60°C
A range of adjustable shower rails (chrome plated brass) with EPDM O-rings.
Non-metallic materials and components comply with BS6920 at 65°C
Range of stainless-steel interlocked shower hoses and handsets (chrome plated plastic). Model 27803845 is supplied with a wall elbow (chrome plated brass body) and incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Shower hand set incorporates an approved shower handset, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Shower handset incorporating a plastic body. The inlet incorporates a plastic flow reducer & stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower outlets, comprising of overhead showers and a shower handset (chrome plated plastic bodies). Models 88500077 Amber 2, 88600025 Kelsey 2 & 88600027 Isable 3 have a maximum operating temperature of 65°C. Model 88600042 has a maximum operating temperature of 60°C.
Range of shower handsets and shower heads with chromium plated plastic bodies. The shower heads incorporate a stainless steel strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of showerheads and shower handsets with chromium plated ABS bodies. Showerheads incorporate a stainless-steel strainer. Open outlets use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of showers handsets with plastic bodies (chromium plated, matt black for model P75502). Model P86300 is supplied with an optional flow restrictor. Model P60901 & P70400 incorporates an approved single check-valve at the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of ceiling or wall mounted shower outlets, (brass or stainless-steel bodies - various finishes) incorporating EPDM `O` rings. Maximum operating temperature 60.0°C
A range of ceiling mounted and wall mounted shower outlets (brass and stainless-steel bodies - various finishes) incorporating EPDM O-rings.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets, (plastic bodies - various finishes), incorporating a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 60°C
Range of ceiling mounted overhead shower outlets, (plastic bodies - various finishes), incorporating a stainless-steel strainer and flow regulator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets (plastic bodies – various finishes).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets and an overhead shower outlet with plastic bodies (chrome plated, chrome plated/white or chrome plated/black coloured finish - see model). The inlet of the 2.1981.018 model incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Non-metallic materials and components comply with BS6920 at 55°C
In-line strainers with a stainless steel or blue epoxy coasted cast iron body, stainless steel strainer and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Cold water use only.
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Pillar tap (chromium plated brass) incorporating a quarter turn ceramic disc headwork with single lever type headwork. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pillar taps (chromium plated brass), incorporating quarter turn ceramic disc headworks, available with either cross top (400145 & 400146) or single lever (310802 & 310803) operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal back nuts Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (Models A05017, A05018, A05490 & A05491) or a plastic aerator (Models A05029 & A05030). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C for all models except A05490 & A05491 which are 85°C
Range of stainless steel interlocked shower hoses with PVC or PEX inner liner and EPDM washers.
Non-metallic materials and components comply with BS6920 at 65°C
Range of stainless-steel interlocked, PVC lined shower hoses available in lengths between 50cm & 200cm.
Non-metallic materials and components comply with BS6920 at 65°C
‘Luxor type PEX’, range of stainless steel braided hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of stainless steel interlocked shower hoses with an EPDM inner liner and EPDM washers.
Non-metallic materials and components comply with BS6920 at 65°C
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of wall mounted, concealed manually blending shower valves, incorporating a ceramic cartridge headwork and various lever operating members. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, manually operated shower valves, (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed, three-way, manual shower blending valves with a brass body and a chrome plated trim set. Flow is controlled by a ceramic cartridge headwork with a single lever operating member. This supplies a lower outlet as well as a separate two-way ceramic disc diverter. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of T-type thermostatic mixing valves (chrome plated brass bodies). Temperature is pre-set under fixed cap. The inlets incorporate fibre washers, stainless-steel EPDM strainer washers and approved single check valve cartridges, however, (the complete product has not been fully tested to demonstrate it provides backflow protection). The inlets for models MT503CP-ISO & MT503CP-ISOELB also incorporate screwdriver operated isolation valves. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted thermostatic bar shower mixers (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. Model RYBS01 incorporates cube type operating members. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with shower hoses, shower handsets and riser rail assemblies. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed thermostatic blending valves or exposed bar type thermostatic blending valves (chromium plated brass) incorporating a 2-way manual diverter valve controlling and diverting the flow between an overhead shower and a shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button incorporate. An approved check valve cartridge is also supplied, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower head, shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (NU-019 & NU-022 models. All other models 60°C only).
Wall mounted thermostatic shower valve, (brass body - various finishes) incorporating a ceramic disc diverter headwork controlling the flow to the hand shower or overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge a with single lever operating member which incorporates a manual override. The valve and shower head inlets incorporate stainless steel strainer washers with a flow regulator in the shower handset. The valve and shower handset inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose, handset, and overhead shower outlet. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of thermostatic shower mixing valves, (brass bodies - various finishes). The temperature is controlled via thermostatic cartridges with cross top operating members and the flow is controlled via two quarter turn ceramic disc headworks with single lever operating members. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose, handset, overhead shower and riser rail assembly. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, manually operated, thermostatic blending valves with chrome plated brass bodies. The temperature is controlled via a thermostatic cartridge using a dome type operating member. Inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of concealed, thermostatic blending valves with 2 or 3 shower outlets, incorporating a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button and ceramic disc diverters or quarter turn ceramic disc headworks controlling the flow with dome type operating members. The products incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, thermostatic blending valves, (chrome plated brass bodies) incorporating two detent headworks controlling the flow. The temperature is controlled independently via a thermostatic cartridge with switch type operating member that incorporates a manual override button. The product is supplied with an overhead shower, shower hose, handset and riser rail assembly. The inlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of high pressure and low pressure thermostatic mixing valves. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Low pressure models incorporate a pump. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves marked with ‘LP’ have a maximum working pressure of 1.0 bar.
Non-metallic materials and components comply with BS6920 at 45°C
Range of wafer, lugged and flanged type butterfly valves with bronze, stainless steel or ductile iron bodies (orange epoxy coated) with bronze, stainless steel or ductile iron disc materials and EPDM seats. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Range of manually operated double regulation and commissioning valves with gunmetal bodies, incorporating a PTFE sealing ring and EPDM ‘O’- rings. Flow is controlled via a non-rising spindle headwork. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 45°C or 65°C, please refer to model.
Range of in-line adjustable pressure reducing valves, with DZR brass bodies and EPDM membrane. Maximum inlet supply pressure 16.0 bar. Outlet pressure 1.5 bar to 6.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
‘Jet 806’ range of pre-set pressure relief valves incorporating gunmetal bodies, PTFE seat and lever operated easing gear. Each valve is available with a pre-set rating of between 1.0 bar and 12.5 bar, in increments of 0.1 bar. Maximum operating temperature 95˚C.
‘Jet 806’ range of pre-set pressure relief valves incorporating gunmetal bodies, PTFE seat and lever operated easing gear. Each valve is available with a pre-set rating of between 1.0 bar and 12.5 bar, in increments of 0.1 bar. Maximum operating temperature 95˚C.
Range of normally closed, normally open or latching inline solenoid valves with brass bodies and EPDM ‘O’-rings and diaphragms. Maximum working pressure: PU225DN-03, PU225DN-04, PU225DN-08, PU225DN-12, PU225DN-14, LPU225D-03, LPU225D-04, LPU225D-08, LPU225D-12 & LPU225D-14 models - 7.0 bar. All other models - 10.0 bar. Cold water use only.
AVK series 41 range of swing gate valves with blue epoxy coated ductile iron bodies and metal to metal seal. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with bronze bodies, incorporating PTFE seats and chromium plated brass balls. Maximum working pressure 40.0 bar. Maximum operating temperature 100°C.
In-line spherical valve with a chrome plated DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Export’ range of lever or butterfly handle spherical valves with nickel plated brass bodies, chrome plated brass balls, PTFE seats, and NBR ‘O’-rings. Compression connection models are for use with copper pipe (manufactured to BS EN1057). Maximum working pressures: see models.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
A range of in-line, lever operated spherical isolation valves with chrome plated brass bodies & chrome plated balls, stainless steel wire filters and plastic flow regulators. Compression connections to be used with copper pipe EN1057 only. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C except for models AI-811215 & AI-81121518 CST with temperatures of 85°C
Range of resilient seated gate valves with ductile iron bodies and bonnets (blue epoxy powder coated) with a ductile iron wedge encapsulated in EPDM. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Talbot range of gunmetal screw down stop valves for use with MDPE PE80 pipe (manufactured to EN12201). The products are supplied with loose (blue plastic) pipe inserts. Maximum working pressure 16.0 bar. Cold water use only.
Range of brass and DZR brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitors with chromium plated copper bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 35°C
Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
'ABS Bianco CP .2503 HI70' (also known as DWKRAL ABS Bianco 4698 AT). White coloured, injection moulded ABS material. For use with water up to 35°C.
'Kealox 96% & 99.7%'. White coloured, compression moulded ceramic rings. For use with water up to 85°C.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TEPICOMPOWDER PC-200F U'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EE8000 – 5006836 & EE8000-5006835'. Factory applied, blue coloured epoxy powder coatings. Apply by fusion bond dip as per Product Data Sheet 'version 5.0' dated '25/07/2024'. Cure for 7 minutes@200°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 High chlorinated polyethylene anticorrosive coating'. Factory applied, blue coloured polyethylene coating. Apply as per manufacturer's TDS/IFU number '001', dated '2022.11.30'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELEC GRP PIPE B'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'SHUANGSHI GRP PIPE 51160'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'PROTEAN Silicone Paste'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Denyl 66 3010 Natural F' & 'Denyl 66 3010 Black F'. Natural (appears off-white) and black coloured, injection moulded, Polyamide 66 materials. For use with water up to 65°C.
'EPLAMID 66 GFS 30 FW NC'. Natural (appears beige), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
'EPLAMID 66 GFS 30 FW BK'. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
'TEGA PE100 fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Stars Water Tank Panel'. Multi-layered, roto-moulded LLDPE/PE foam panel comprising of a white (opaque) water contact layer, off-white (translucent) second layer, black (opaque) third layer and white (opaque) outer layer. For use with water up to 65°C.
'DERINSU PE100 Fitting'. Black coloured, injection moulded PE100 fitting. For use with water up to 60°C.
'UNIDELTA Electrofusion Fitting'. Black coloured, injection moulded PE100 Electrofusion Fitting. For use with water up to 60°C.
'Cosmoplast Butt Fusion Fitting'. Black coloured, polyethylene butt-fusion fitting. For use with water up to 60°C.
'Wefatherm Fitting'. Green coloured, injection moulded PP-R fitting. For use with water up to 60°C.
'Wefatherm Pipe'. Green coloured (with or without blue external stripe), extruded PP-R pipe. 'Wefatherm Fibre Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R/fibre middle layer and green coloured (with red stripe) PP-R outer layer. Both pipes are for use with water up to 60°C.
'Aquatherm Fitting'. Green coloured, injection moulded polypropylene fittings. For use with water up to 60°C.
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
'FKM 90 Black 6019020105-CMP00700'. Black coloured, compression moulded FKM material. Shore hardness 90. Tested in-radius size 1.1mm. For use with water up to 85°C.
‘N5118F, N5518F, N6118F, N6518F, N7118F, N7008F, N7518F, N8118F, N8518F & N9118F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
‘2061 VMQ 60’, red coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 60. ‘2172 VMQ 70’, blue coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 70. O-rings have a tested in-radius of 2.0mm Washers have a tested in-radius of 2.5mm. Lip seals have a tested in-radius of 0.45mm For use with water up to 85°C.
‘Loctite® 55’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Technical Data Sheet ‘reference 1.9’, dated August 2016 and this material is only approved for these conditions. For use with water up to 85°C.
3-in1 single hole, single outlet (swivel) combination tap assembly (chromium plated or brushed stainless steel PVD brass). The cold//hot/mixed water circuit incorporates a ceramic cartridge headwork with a single lever operating member. The near boiling water circuit incorporates a quarter turn ceramic disc headwork with a single lever operating member. The tap is supplied with a stainless steel braided PEX lined flexible hose assembly, brass adaptor incorporating a plastic flow regulator, NBR washer and plastic adaptor to connect the tap to the near boiling water unit (not supplied) and a PTFE or silicone (from September 2024) flexible pipe to deliver near boiling water back to the tap. The spout outlet incorporates a plastic aerator, which includes a central stainless steel tube insert throughout the near boiling water outlet of the aerator. Maximum working pressure 10.0 bar. Maximum operating temperatures: 65°C (cold/hot/mixed water circuit). 99°C (near boiling water circuit after boiler unit, cold supply only prior to boiler unit).
Single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated – brass bodies). Flow is controlled via a solenoid which is actuated via an infrared sensor and the temperature is controlled by a manual lever. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and a manual lever to control the outlet temperature. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Temperature:60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass bodies). Flow is controlled via a solenoid, activated via an infra-red sensor. The outlets incorporate plastic aerators. Maximum working pressure 8.0 bar Maximum operating temperature 70°C
Non-metallic materials and components comply with BS6920 at 70°C
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating quarter turn ceramic disc headworks with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a hand held pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. These products are supplied with metal back nuts. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole single outlet fixed combination tap assemblies, (chrome plated brass), incorporating a quarter turn ceramic disc headwork with a single lever operating member and non-rising spindle headwork with a variety of operating members (See models) controlling the flow to the additional swivel spout. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). The inlets incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the swivel spouts incorporates plastic aerators. Maximum working pressure 8.6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating either quarter turn ceramic disc or quarter turn compression washer headworks with various operating members (see model). The inlets of the quarter turn ceramic disc headworks incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model). The product is supplied with metal backnuts. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes ) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied either with or without a lever type pop-up waste set (see models). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The inlets of 2621 models incorporate plastic strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets of 26216 models incorporate single check valve cartridge assembly (suitable for backflow protection against fluid category 2), plastic strainers and a single lever operated spherical valves. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Page 3 of 9
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
