Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of manually operated balancing valves with DZR brass bodies. The product also incorporates a spherical valve. Maximum working pressure: 10 bar Maximum working temperature: 100°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of electronic water de-scaler and conditioners with stainless steel bodies. Maximum working pressure 10 bar. Maximum operating temperature 40°C
Electrolytic inline limescale reducer with a zinc plated brass body and a copper coil. Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
Range of UV Disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured, fusion bonded epoxy powder coating. Pre-heat substrate to be coated for 15 minutes@200°C and coating applied as per manufacturer's TDS dated '22 August 2018'. Post-cure for 15 min@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polymer Admixture 850'. Site applied, white coloured liquid primer/sealer. Mix 'Polymer Admixture 850' & water in a volume ratio of 1:1 and apply as per manufacturer’s Product Data Sheet dated Jan 2023. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Supranite 2400'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'UW TPE HEA-ISO (manufactured from NAKAN HEA 407 EX)'. White coloured (translucent), extruded TPE hose. Shore hardness 66. Tested in-radius size 0.39mm. For use with water up to 65°C.
'Promag D - Flowtube'. Black coloured, injection moulded PA flowtube. For use with water up to 60°C.
'3802B'. Black coloured, extruded MDPE material. For use with water up to 23°C.
'HEPWORTH uPVC Pressure Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 60°C.
'+GF+ uPVC Pressure Pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 60°C.
'E7331'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'Butyl IIR 6038 diaphragm'. Black coloured, injection moulded Butyl diaphragm. Shore hardness 64 ShA. Tested in-radius size 1.25mm. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The E2WXX, E2BXX & E2GXX models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The E1WXX & EW1WXX models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve that is activated via an infrared sensor. Certain models incorporate a mixer spout which incorporates a manual temperature control. The spout outlets also incorporate a plastic flow straighter. Maximum working pressure; 5 Bar Maximum operating temperature: 60°C
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with nickel plated or natural finish. Models with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Models 12.10152.015.CP02-8511 & 12.10152.015.CP5R-8511 have a maximum operating temperature of 65°C. All other models have a maximum operating temperature of 85°C
Non-verifiable double check valve assembly with DZR brass body (chrome plated), incorporating two in-line check valve cartridges. Maximum working pressure – 10.0 Bar Maximum operating temperature - 85°C
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates an isolation valve and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Drayton GRP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of single hole, single outlet swivel nozzle combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with cross top operating members. The outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste, not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Ceramic cartridge headworks with a plastic body, incorporating silicone seals and NBR O-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), models EMB10CP, EMB10BN, EMB10BB, EMB10MB, EMB10WH, CREPOCP & CREPOBN incorporate ceramic cartridge headworks, model (ARI10CP, ARI10BN, ARI10BB, ARI10MB & ARI10WH incorporates quarter turn ceramic disc headworks both with single lever operating members. The spout outlet is a pull-out spray type. The inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Deck mounted, single hole, single outlet fixed combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. This product also incorporates an additional spring-loaded quarter turn ceramic disc headwork with a single lever operating member for filtered cold water discharged from the spout outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single-hole, single outlet (swivel) combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied mounting kit that comprises of stainless-steel braided hoses and isolation valves that incorporate approved single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The cold only inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The cold inlet hose and the spout outlet incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 75.0°C
Range of wall mounted, two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Model (TVW125003000xx) is supplied with a click type waste (verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet fixed combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with dome or lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Two hole, single outlet fixed combination tap assembly (chrome plated brass body) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless strainer and an approved single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 10 bar. Maximum operating temperature 65 °C
Range of combined bath filler and/or waste and overflow assemblies (see models) in various finishes. Open outlet use only Maximum operating temperature: 60ºC
Range of tap adaptors with chrome plated (brass or plastic) bodies. The outlet of some models incorporates a plastic flow restrictor. The side mount adaptors (except 90-001801) incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The side mount adaptors (except 90-001804) incorporate a piston type component which is intended to stop the flow to change the filter. All side mount adaptors and 90-001869 & 90-001873 Fixed Position Adaptors have a maximum working pressure of 5.0 bar. All other models are open outlet use only. Maximum operating temperature 60°C.
Range of exposed bath fillers (brass body, various finishes) incorporating a ceramic cartridge headwork, controlling both flow and temperature with a single lever operating member. The products incorporate integrated overflow and click type pop-up waste systems. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of swivel or fixed spout outlets (chromium plated brass) incorporating a plastic aerator. Open outlet use only Maximum operating temperature 60.0°C
Range of expansion vessels with fibreglass bodies and butyl diaphragms. Maximum working pressure: 8.6 Bar. Maximum operating temperature: 23 °C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “SOUTH PRESS” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
A range of black polyethylene electrofusion fittings from DN 20 to DN 1200 for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. A range of black polyethylene butt-welded fittings from DE 20 to DE 1200 fittings for use with PE100 and PE100-RC pipes conforming to EN 12201 or ISO 4427. Maximum working pressure: 20.0 bar for SDR 9 Maximum working pressure: 16.0 bar for SDR 11 Maximum working pressure: 10.0 bar for SDR 17. For above and below ground and cold water use only.
‘Safety’ range of PPS compression fittings for use with “Multi-Calor” multi-layered PEX/Al/PEX pipe. For above ground use only. Maximum working pressure 10bar. Maximum operating temperature 95 °C.
‘Pexalbrass’ range of brass press fittings for use with “PEXAL” multi-layered (PE-X /Al/PE-X) pipe. Joints are achieved via crimping tool for H (DN16, DN20, DN26, DN32), TH(DN16, DN20, DN26, DN32, DN40, DN50, DN63), U (DN16, DN20, DN26, DN32, DN40, DN50, DN63, DN75, DN90, DN110) profile. Maximum working pressure 10bar. Maximum operating temperature 95 °C.
Range of brass threaded fittings,. Above ground use only. Maximum operating pressure of 16.0 bar. Maximum operating temperature of 85°C.
Range of brass (CW617 or CW511L) press fit fittings (M-Type) for use with copper pipe manufactured to EN 1057. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.
Float switch with plastic body. Maximum working pressure 1.2 bar. Maximum operating temperature 23°C.
Range of WC dual flush drop valve comprising of a plastic body, silicone seating washer and an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Range of WC single flush flapper valves with an ABS body. The valves are operated via a lever handle or a push button assembly and incorporate an internal overflow. Cold water use only
Range of near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of electronic pump controllers with plastic bodies. Maximum working pressure 12.0 Bar. Cold water use only.
Range of pressure transducers with stainless steel bodies. Maximum working pressure 10.0 Bar, 20 Bar or 40 Bar. Maximum operating temperature 99°C.
Range of booster sets, incorporating a stainless-steel manifold system and between 2 and 5 pumps depending on model. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels. Maximum working pressure 16.0 Bar. Maximum operating temperature 25.0°C.
Plastic shower handsets with various finishes. Maximum operating temperature 65.0°C Open outlet use only
Range of shower handsets and overhead showers with (plastic or chrome plated plastic bodies). Open Outlet use only Maximum operating temperature 75.0°C
Shower handset with various finishes. Maximum operating temperature 65°C.
Shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
Range of shower handsets and overhead shower with various finishes. Model HS149 incorporates a stainless steel strainer washer at the inlet. Maximum operating temperature 65°C.
Range of overhead showers incorporating ABS (plastic bodies - various finishes), stainless steel strainer and flow restrictor (flow restrictor only on “minus flow” models) in the inlets. Open outlet use only. Maximum operating temperature 60.0°C
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of flanged `Y` patterned in-line strainers with blue epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of ‘Y’-pattern strainers with blue epoxy coated ductile iron bodies and a stainless-steel screen. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of bib taps (chrome plated brass) or (DZR brass) bodies – see models, incorporating a spherical valve to control the flow. The products incorporate single lever operating members. Some models are supplied with lock shields (see models). The spout outlet incorporates a hose union spigot connection with a plastic flow straightener. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bib taps (chrome plated brass) or (DZR brass) bodies – see models, incorporating a spherical valve to control the flow. The products incorporate single lever operating members. Some models are supplied with lock shields (see models). The spout outlet incorporates a hose union spigot connection with a plastic flow straightener. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of pillar taps (chromium plated brass) incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass) with non-rising spindle or quarter turn ceramic disc headworks, with dome type, cross top or lever type operating members. The spout outlets incorporates a plastic flow straightener. Products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, self-closing, push-button operated tap assemblies (chromium plated brass) incorporating non-concussive headwork with dome type operating member. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models 794160 & 794165 incorporate spherical valves at the inlets. Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
Nylon braided flexible hose with a 'PE-BWG' inner hose. The hose incorporates a brass ball stem connection. Maximum operating temperature 85.0°C
Range of nylon braided PEX lined flexible hose assemblies with EPDM washers and ‘O’-rings with a variety of end connections. Maximum operating temperature 65.0°C
Range of PVC flexible shower hoses with a PVC inner hose. Maximum operating temperature 85°C.
Range of PEX lined stainless steel braided flexible hose assemblies with brass end connections. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°c.
Range of dual layer supply hoses for use with free standing appliances. Available with a grey, blue or red PVC outer layer and black PVC inner layer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of shower hoses, with either a interlocked stainless steel outer hose (PVC or PEX inner hose - YHR01-A-A-**-**-**& YHR02-A-A-**-**-**); or a PVC outer hose (YHR03-A-A-**-**). Open outlet use only. Maximum operating temperature 65°C.
Range of stainless steel inter-locked shower hoses incorporating PVC linings in various finishes. Maximum operating temperature 65°C.
‘FlexPlus’ range of EPDM lined stainless steel braided flexible hose assemblies with brass end connections. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of 2, 3, 4 and 5 port manifold assemblies with brass bodies (various finishes) for use with copper pipe (BS EN 1057) and South Press range of PEX/AL/PEX multilayer pipe. Some models have non rising spindle headworks control valve in the ports. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 95.0°C.
Air venting valve with brass body and stainless-steel float. Maximum working pressure 13.5 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, manually operated blending valves (brass bodies – various finishes) incorporating 1 way or 2 way function ceramic disc headworks. The products are supplied with single lever operating members. The inlets incorporate single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of T-type thermostatic mixing valves with DZR brass bodies. Temperature is pre-set under a fixed cap. The inlet adaptors incorporate single check valve cartridges (verified by test, suitable for backflow protection against Fluid Category 2) and stainless-steel strainers.
Range of wall mounted, concealed thermostatic shower valves (plastic bodies),2 way or 3 way function incorporating push button headworks controlling the flow to either shower outlets. The temperature is controlled independently via a thermostatic cartridge. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of T type thermostatic blending valves with DZR brass bodies (chrome plated). The inlets incorporate stainless steel strainers and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10 Bar. Maximum operating temperature 65°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies & wedges and EPDM sealing gasket. The closing mechanism is controlled by a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85˚C.
Range of wafer, lugged or flanged butterfly valves with blue epoxy coated ductile iron bodies and discs, with lever type or handwheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of flanged butterfly valves with blue epoxy coated ductile iron bodies and discs, with handwheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lugged, flanged and wafer butterfly valves with ductile iron blue epoxy coated bodies. The valves are operated by either a lever or gearbox (see models). Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of lugged, semi lugged, wafer type or U shaped (see models) butterfly valves with a blue epoxy coated cast iron body, EPDM seat and either a stainless steel, bronze, EUROKOTE - EBONITE or blue epoxy coated iron disc (see models). Maximum working pressure 6.0, 10.0 or 25.0 Bar (See models) Maximum operating temperature 23.0 or 60.0°C (See models)
Range of control valves with nylon bodies, stainless steel springs, EPDM diaphragms and O-rings. Maximum working pressure 16 Bar. Cold water use only.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-return, swing gate valves with bronze brass discs. Maximum working pressure 20.0 bar or 16.0 bar (please refer to model) Maximum operating temperature 85°C.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies. Some models have a pressure connection and can be supplied with the pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure 1.0 to 6 bar. Maximum operating temperature 80°C
Range of pilot operated, pressure reducing valves epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, spherical valves and a needle valve. Outlet pressure setting is adjustable in the range of 1.0 bar to 12.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.
Spherical valves incorporating bronze bodies with lever operating members, chromium plated brass ball and PTFE seat. Maximum working pressure 25.0 bar, Maximum operating temperature 85°C.
Range of spherical valves (brass bodies - various finishes) with press fit connections for use with “South Press range of PEX/AL/PEX multiplayer pipe. Maximum working pressure: 10Bar. Maximum operating temperature: 95°c.
Range of press fit spherical valves with chrome plated brass bodies, to be used with copper pipe EN1057. Crimp joint is achieved by a M profile crimp. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with either brass (BFIVB-15, BFIVBL-15 & BFIVHPL-15 models) or nickel plated (BFIV-15, BFIVL-15,BFIVL-22 & BFSVB-15D models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Screwdriver operated spherical valve with a brass & DZR brass body. The fitting incorporates two approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
Screwdriver operated spherical valve with a DZR brass body. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of lever or handwheel operated spherical valves with stainless steel body, stainless steel ball and PTFE seals. Maximum working pressure 20.0 Bar (Models Series 65 & Series 73) Maximum working pressure 50.0 Bar (Models Series 66 & Series 74) Maximum operating temperature 85.0°C
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Spherical valves incorporating a drain port and two check valve cartridges (verified by test, suitable for backflow protection against fluid category 3) in a DZR brass body. Above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a DZR brass body, incorporating a stainless-steel ball. The press fit connections are to be used with copper pipe to BS EN1057 and the crimp joint is achieved by a M and V profile crimp jaws. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The TCDIGVR16 & TCDIGVR25 models has a rising spindle, the TCDIGVN16 & TCDIGVN25 models has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of gate valves with brass bodies and wedges. Maximum working pressure 17.5 bar. Maximum operating temperature 93°C
Range of resilient seated gate valves incorporating ductile iron bodies with blue epoxy coated finish. The valves incorporate either rising (G series) or non-rising spindles (GNS series) and have an EPDM wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flanged gate valves incorporating ductile iron bodies with blue epoxy coated finish. Maximum working pressure 10.0bar. Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies. Maximum working pressure 17.24 Bar Maximum operating temperature 99.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
Range of gate valves with blue epoxy coated ductile iron bodies and handwheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of bronze gate valves incorporating bronze wedges, non-rising stems. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
`Water block` range of self-closing valves with either a natural (white), blue or grey plastic body and a gear driven volume-controlled operation device. The product incorporates a stainless-steel strainer. The product is designed to stop the flow of water once a preset value (in litres) has been reached. User intervention is then required to reset it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of pilot operated electronic flow control valves having flow control facility intended to be controlled via solenoid valves, with auxiliary components including stainless steel tubing, cock valves, needle valve and a stainless-steel strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
UV disinfection unit with stainless steel body and quartz sleeves. Maximum working pressure 3.0 bar. Maximum operating temperature 35°C.
Range of plastic water meter manifold adaptors incorporating plastic flow regulators and sampling adapter. Above ground use only. Maximum working pressure: 12.5 Bar. Maximum working temperature: 23°C.
'CELCON F10-52H Blue'. Blue coloured, injection moulded POM material. For use with water up to 40°C.
'CELCON F20-03 BKM'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'CELCON F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘CELCON F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch CELCON MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'CELCON F10-03H BBK & CELCON F10-03H BK'. Black coloured, injection moulded POM materials. For use with water up to 85°C. 'CELCON F10-52H'. Natural (appears white), injection moulded POM material. For use with water up to 40°C.
'FORMOCON FM090'. White coloured, injection moulded POM material. For use with water up to 85°C.
'FORMOCON FM270'. White coloured, injection moulded POM material. For use with water up to 85°C.
'FORMOCON FM130'. White coloured, injection moulded POM material. For use with water up to 85°C.
'FORMOCON FM090LMD'. White coloured, injection moulded POM material. For use with water up to 85°C.
'DURACON® GH-25W WK3500'. White coloured, injection moulded POM material. For use with water up to 85°C.
'EVER-BLACK 1'. Factory applied, black coloured, modified bitumen coating. Apply as per manufacturer's TDS TDS 'V1', dated '2023.03.05' and cure for dry/cure for 7 days@25°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F (SPD)'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's TDS 'RP23242', dated 'December 26, 2023'. Cure for 6 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EKOPIPE 900 Blue’. Factory applied, blue coloured, two-component epoxy coating. Mix parts A & B in a mass ratio of 2:1 and apply as per manufacturer's TDS 'No:09, Rev.Date: January 2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VALVFIT 001 (blue) & VALVHIT 002 (red) Epoxy Powder Coatings'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'VALVFIT-2412001' dated '12.17.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 860'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/05/2023'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SikaTop® 550 Seal’. Site applied, white coloured, two component Acrylic, Cementitious waterproofing coating. Mix 1kg of part A (powder) with 333g of part B (liquid) and apply as per manufacturer’s method statement ‘10/2024’. Cure for 28 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPS GRP fitting'. Multi-layered fitting comprising of a pale green coloured inner layer and yellow/brown coloured outer layer, manufactured by hand-layup. For use with water up to 60°C.
'KN133G30 (off-white in colour) & KN133G15BL (black coloured)'. Injection moulded PA6 materials. KN133G30 is for use with water up to 65°C. KN133G15BL is for use with water up to 23°C.
'Tufcot T100'. Off-white coloured, polyester composite material manufactured by hand lay-up. For use with water up to 23°C.
'SUDA HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Draka Comteq Cable Sheath: R607581 and R698927. Black coloured, extruded polyethylene cable sheath. For use with water up to 85°C.
‘Georg Fischer (+GF+) HDPE PE100 Pipes and ‘Hepworth MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'HEPWORTH Pipe'. Black coloured, extruded LDPE pipe. For use with water up to 60°C.
'Hepworth MDPE PE 80 Black Pipe'. Black coloured (with blue external stripes), extruded MDPE pipe. For use with water up to 60°C.
'Polyfab PE100 Pipe' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured (with blue external stripes), extruded PE100 pipe. For use with water up to 85°C.
'Polyfab PE100 Fittings' (manufactured by Polyfab Plastic Industry LLC in Ajman & Kizad). Black coloured, injection moulded PE100 fittings. For use with water up to 85°C.
+GF+ MDPE PE 80 Black Pipe'. Black coloured (with blue external stripes), extruded MDPE pipe. For use with water up to 60°C.
‘+GF+ HDPE PE100 Pipes' and '+GF+ MDPE PE80 Pipes’. Black coloured (with or without blue stripes), extruded PE100 pipes. Black coloured, extruded PE80 pipes. For use with water up to 60°C.
'+GF+'. Black coloured, extruded LDPE pipe. For use with water up to 60°C.
'PF HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'ELGEF PLUS'. Black coloured, injection moulded HDPE electrofusion and spigot fittings. For use with water up to 60°C.
'CR-01 PE Pipe'. Blue coloured, extruded PE pipe. For use with water up to 23°C.
'CR-02 PE Fitting'. Blue coloured, injection moulded PE fitting. For use with water up to 23°C.
'FLEXIPOL MASA'. Black coloured (with blue stripes), extruded polyethylene pipes. For use with water up to 60°C. The 'FLEXIPOL MASA' pipes covered by the scope of this approval are marked with 'V63'. 'FLEXIPOL MASA' pipes which are not marked with 'V63' are not covered by the scope of this approval.
'Kasta® HDPE PE 100 Pipe (Black)'. Black coloured (with blue external stripes), extruded HDPE pipe. For use with water up to 65°C.
'Egelen PE100 & Egeplast 9010 pipes'. Egelen PE100 is a single layered, black coloured, extruded PE100 pipe. Egeplast 9010 is a dual layered, extruded PE100 pipe consisting of a black coloured inner layer and a blue coloured outer layer. For use with water up to 23°C.
'Revolve N-250 Light Grey M2-5321'. Grey coloured PE material manufactured by rotomoulding. For use with water up to 85°C.
'Revolve N-820 Natural'. Natural (appears off-white), PE material manufactured by rotomoulding. For use with water up to 85°C.
'ISOMAG Cylinder'. Grey coloured, extruded polypropylene cylinder component. For use with water up to 60°C.
'SP Sereneplast'. Green coloured (with external red stripes), extruded PPR pipe. For use with water up to 60°C.
'SP Sereneplast Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 60°C.
'Verplen C3008 VE ACLKUV W (GF 30% green coloured) & Verplen 60NE A W (black coloured'. Injection moulded, polypropylene materials. For use with water up to 60°C.
'Borealis HE125MO & Bn HE125MO-100'. White coloured (semi-opaque), injection moulded PP-H materials. For use with water up to 85°C.
'NOVIPRO Ruban'. White coloured PTFE tape manufactured by press strip roller. For use with water up to 60°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterCrete ANC 920'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1', dated '09.12.2024' Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterCrete ANC 915’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 1', dated '09.12.2024'. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VULKODURIT 1250 KTW'. Dark grey/brown coloured, Ebonite rubber material made by extrusion and calendaring. Shore hardness 72D. Tested in-radius size 2.0mm. For use with water up to 40°C.
'E8124'. Black coloured, injection moulded EPDM seal. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 85°C.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
'E50B01, E70B01 & E80B01'. Black coloured, compression moulded EPDM material. Shore hardness between 50, 70 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'CERULEAN EP 14 (KIEP14)'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'8550C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP55 & EP70'. Black coloured, compression moulded EPDM materials. Shore hardness 55 & 70. Tested in-radii size 1.0mm. For use with water up to 70°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'WAGUNIT H 1005'. Light brown coloured, compression moulded natural hard rubber. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
'LS5006WE (white coloured) & LS5006BK (black coloured). Compression moulded, liquid silicone materials. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Kamco Systemseal Gas & Water Jointing Compound (Product Code: BSS007'). Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'RIAMAXX HR XE4355 KTW-M schwarz & RIAMAXX HR XE4355 KTW-M sondergrau K 7-140‘. Black or grey coloured, injection moulded PK materials. For use with water up to 60°C.
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of spring loaded, resilient trim check valve cartridges with plastic body. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
GRPBP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of single hole bidet combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The swivel nozzle outlet incorporates a plastic aerator and the product is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of flow straighteners with plastic bodies. The JM030503-15 model incorporates a silicone lined flexible hose with an interlocked metal outer. The JM030002-15 model incorporates a swivel ball joint. Both models incorporate a stainless steel mesh on the outlet. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with a plastic body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperatures 85°C (K26PMA-01NP model) and 65°C (K40P-01NPX model).
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Single hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pullout hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Single-hole, single outlet (swivel) combination tap assemblies (brass body – various finishes) incorporating a ceramic cartridge (MARTA CH) or quarter turn ceramic disc (ALTUS CH) headwork with a single lever operating member. The products have a pull-out spray outlet which incorporates a plastic aerator and trigger mechanism that stops the flow (model (ALTUS CH) or changes the water pattern from straight flow to spray (MARTA CH). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a pull-down spray with a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-out spray type. Maximum working pressure 10.0 Bar. Maximum operating temperature 65.0°C.
Single hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet, fixed combination tap assembly (chrome plated brass body), incorporating quarter turn ceramic disc headworks with single operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure; 5 Bar Maximum operating temperature 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies (chrome plated brass body) incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Single-hole, single outlet, fixed, combination tap assembly, (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor-standing single hole, single outlet (fixed) combination tap assemblies (various finishes), incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with shower hose and handset. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of floor mounted single hole, single outlet (fixed), combination tap assembly (various plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet with a dome type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with 3/8” x 15mm reducers incorporating approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is to be used with an instantaneous water heater. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Products incorporate an additional hose outlet and shut-off valve for use with an external domestic appliance. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses for models APL1 & ATE1 incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The pull-out spout outlet incorporates a plastic aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses for models Aquaplay single lever Aquanomic & Aquatech single lever Aquanomic incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The cold inlet hose and the spout outlet incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork and single lever operating member. The pull-out spout outlet incorporates a plastic aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The cold only inlet hoses incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (Chromium plated or brushed nickel finish), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with approved single check valves, verified by test (suitable for backflow protection against Fluid Category 2) with integral servicing valve for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headwork. The spout outlet incorporates a plastic flow straightener and the product is supplied with single check valve assemblies (verified by test as suitable for backflow protection against Fluid Category 2) with integral servicing valve for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (chrome plated brass body), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Inlets incorporate isolation valves that incorporate single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum static pressure 5 bar. Maximum operating temperature 60°C
Single hole, double outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, double outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks and dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assembly (brass body, various finishes), incorporating ceramic cartridge headwork and single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate an aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 65°C
Range of two-hole, double outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic discs headworks and single lever or dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
SuperFlow MCPA, MCMA & MCUA ranges of expansion vessels. Maximum working pressures: MCPA Series = 10.0 bar, MCMA Series = 16.0 bar, MCUA Series = 25.0 bar. Maximum operating temperature 65°C.
Inline filter with plastic body. Maximum working pressure 5.0 bar. Cold water use only.
Range of in-line carbon block water filters and housings with polypropylene bodies. Maximum working pressure 8.0 bar. Cold water use only.
Range of brass press fittings (TH and U crimp profiles) for use with RIIFO B1 PEX/AL/PEX multilayer pipe. Maximum working pressure: 10 bar Maximum operating temperature: 95 °C
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use (sizes 12mm-54mm only. 66.7mm, 76.1mm, 88.9mm & 108mm for above ground use only) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PCC type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Tectite Classic and Tectite Pro ranges of copper alloy push-fit fittings The Tectite Classic range is for use with copper tube (manufactured to BS EN 1057) and PEX & Polybutylene tube (manufactured to BS 7291). The fittings are supplied with plastic inserts. The Tectite Pro range is for use with copper tube (manufactured to BS EN 1057). Maximum working pressures & operating temperatures: Tectite Classic fittings with copper pipe: 6.0 bar @ 95°C, 16.0 Bar cold water use. Tectite Classic fittings with PEX & Polybutylene 6.0 bar @ 95°C, 12.0 Bar cold water use. Tectite Pro fittings (15mm - 28mm): 6.0 bar @ 95°C, 20.0 Bar cold water use. Tectite Pro fittings (32mm - 54mm): 6.0 bar @ 95°C, 16.0 Bar cold water use.
WC dual flush valves with a plastic body and incorporates an internal overflow. Cold water use only.
Range of urinal flushing mechanisms, consisting of a solenoid valve controlling the flow which is actuated via an infra-red sensor. Models are either mains or battery operated and are available in a variety of enclosure options Maximum operating pressure 8 bar. Maximum operating temperature 23°C
Range of ultrasonic water meters with brass or stainless steel bodies and plastic or stainless steel transducers. The SC-F models incorporate a spherical valve operated via a motor controlled by computer software. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line water meters with stainless steel bodies Maximum working pressure 10.0 Bar. Maximum operating temperature 50.0°C.
Range of water meters with blue epoxy power coated cast iron bodies, incorporating plastic turbines, NBR ‘O’-rings and gaskets. Maximum working pressure 16.0 bar. BS6920 50°C.
Range of water meter manifolds with plastic bodies. The inlets incorporate a spherical valve. Models ending in ‘CGDM’ incorporate a single check valve cartridge and models ending in ‘CGDCVDM’ incorporate two, single check valve cartridges however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meter manifolds with plastic bodies, incorporating plastic pushfit inlets and plastic pushfit outlets. The inlets incorporate a spherical ball valve. Models MB40408256DCVDM & MB40408254DCVDM incorporate two single check valve cartridges, all other models incorporate one single check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16 bar. Cold water use only.
Range of water meter manifolds with plastic bodies, incorporating plastic inlets and gunmetal outlets. The inlets incorporate a spherical ball valve. Models MB40408036CGDCVM & MB40408034CGDCVM incorporate two single check valve cartridges, all other models incorporate one single check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16 bar. Cold water use only.
Range of shower booster pumps with brass bodies and plastic impellers. The body incorporates a single check valve cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Maximum working pressure: 4.0 bar. Maximum operating temperature: 70°C.
‘UPM10’ and ‘UPM20’ range of circulator pumps with a stainless-steel body, plastic impellor and EPDM ‘O’-rings. The product is supplied with EPDM gaskets for the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
'HYDRO MULTI-E' booster set range consisting of two to four electronically controlled pumps connected in parallel and mounted on a common base frame provided with all necessary fittings. The suction manifold incorporates an isolation valve fitted between it and the individual pumps, and a pressure switch with an isolation valve. The discharge manifold incorporates an isolation valve and a non-return valve (not suitable for backflow protection), which is fitted between it and the individual pumps, it also incorporates a combined isolation and drain valve. Maximum working pressure 16.0 bar. Cold water use only.
Self-priming single stage pump, with stainless steel body, plastic impellers, stainless steel shaft, NBR 'O'-rings and seals. Maximum working pressure 6.0 bar. Maximum operating temperature 45°C.
Dutypoint ‘VMV’ range of cold water supply booster sets, incorporating 2 to 8 pumps with a modular stainless steel manifold system. VMV2, VMV3 and VMV4 pump sets are available with DN80 to DN150 manifolds depending on application. VMV5, VMV6, VMV7 and VMV8 pump sets are available with DN150 to DN200 manifolds, depending on application. The products incorporate spherical valves on both the suction and discharge manifolds, with expansion vessels, isolation valves, pressure gauges and transducers on the discharge manifolds only. Maximum working pressure 16.0 bar. Cold water use only.
Range of pumps with plastic bodies, pistons and TPE diaphragm. For use with John Guest LLDPE pipe. The products incorporate non-return valves (not suitable for backflow protection). Maximum working pressure: 8.27 Bar. Cold water use only.
Range of ceiling mounted shower heads (chrome plated brass bodies). Inlets incorporate plastic flow regulators and single check valve cartridges (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). Open outlet use only. Maximum operating temperature 60°C.
Range of shower handsets with ABS plastic bodies (various finishes, see models). Maximum operating temperature (see models).
Range of plastic bodied shower outlets, available in chrome plated or black finish (AQ055082 and B suffix models only). The overhead showers incorporate a combined silicone washer and stainless steel strainer on the inlet. Maximum operating temperatures: 65°C (AQ055062, AQ055063 & AQ055081 models). 75°C (all other models).
Range of overhead shower outlets with (brass bodies – various finishes) incorporating stainless-steel filter washers at the inlet. Maximum operating temperature 85°C.
Range of shower outlets with brass bodies (various finishes) and NBR ‘O’-rings. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of In-line Y patterned strainers with ductle iron bodies (blue epoxy powder coated) and stainless-steel mesh. Maximum working pressure: 16 Bar Maximum operating temperature: 85 °C
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Basin pillar tap (chrome plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar Maximum operating temperature 60°C.
Self-closing basin taps (chromium plated brass) incorporating spring loaded headwork with dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of self-closing taps, (chrome plated brass bodies) incorporating an integrated magnetic headwork. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Self-closing basin taps (chromium plated brass) incorporating spring loaded headwork with dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of stainless steel interlocked or PVC reinforced (see models), PVC inner lined flexible hose assemblies (various finishes). Open outlet use only. Maximum operating temperature 65°C.
Range of PVC shower hoses with EPDM O-rings. Maximum operating temperature 65°C. Open outlet use only.
Range of plastic braided PEX lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
White and grey nylon EPDM lined braided hose. Maximum working pressure 10 Bar. Maximum operating temperature 90°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Nimbus Compact range of combination heat pump units with enamel lined tank and stainless-steel coil. Fitted with a magnesium anode, expansion vessel and T&P valve set at 7 bar & 95°C. supplied with an inlet control group consisting of a pressure reducing valve, strainer, pressure relief valve and single check valve, and a tundish. Max working pressure 6.0 Bar Max operating Temperature 80 °C
Range of automatic air venting valve with bronze bodies. The FTBRZAVW-12 models have a stainless-steel float and a maximum working pressure 12.0 bar. The FTBRZAVW-10 models have a plastic float and a maximum working pressure 10.0 bar. Maximum working pressure - FTBRZAVW-12 models: 12.0 bar, FTBRZAVW-10 models: 10.0 bar. Maximum operating temperature 85°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Wall mounted, manually operated concealed blending valve, incorporating ceramic cartridge headwork with single lever operating member and a shower to shower, self-cancelling diverter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, concealed, thermostatic blending valve incorporating a thermostatic cartridge with a dome operating member and supplied with a trim set. Each inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, thermostatic blending valve (chrome plated brass body). Temperature is pre-set under fixed cap. The inlets incorporate an approved check valve cartridge, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. The product is supplied with plastic strainers and screwdriver operated spherical valves, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic blending shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc two-way diverter headwork controlling the flow with dome or square type operating members. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with dome or square type operating members. The inlets incorporate a stainless-steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted concealed thermostatic blending valves with brass bodies (various finishes), incorporating single sequential headworks with single lever operating members. The inlet couplings incorporate plastic flow regulators & metal strainers. The outlets incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of lug, wafer or flanged (see models) butterfly valves with blue epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with an epoxy coated ductile iron body, stainless steel disc and single lever or handwheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of angled flow control valves with chromium plated brass bodies, incorporating a quarter turn ceramic disc headwork (AGV05Q model) or non-rising spindle headworks (all other models) with dome type operating members. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C.
Range of angle valves with chromium plated brass bodies, incorporating a quarter turn ceramic disc housed within a plastic inner body. The products are available with a variety of dome type operating members. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar (Eurobrass 143 FF) or 3.0bar to 7.0bar (Eurobrass 143 FL). Maximum working pressure: 25.0 bar for Eurobrass 143 FF or 30.0 bar for Eurobrass 143 FL. Maximum operating temperature 80°C.
Range of in-line, manually adjustable pressure reducing valves with nickel plated DZR brass body. Maximum inlet supply pressure 25 bar. Maximum operating temperature 80°C
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar Maximum working pressure: 25.0 bar Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 bar. Maximum operating temperature 80°C.
Range of pilot operated, pressure reducing valves epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, spherical valves and a needle valve. Outlet pressure setting is adjustable in the range of 1.0 bar to 12.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.
Pre-set pressure relief valves, pre-set at 3.0 bar, with a plastic body. Maximum operating temperature 85 °C.
Range of solenoid valves with plastic bodies. The inlets incorporate a plastic flow regulator and optional strainer. Maximum working pressure 10.0 bar. Models which end with ‘H’ have a maximum operating temperature of 85°C. All other models are cold water use only.
Nickel plated brass bodied spherical valve with PTFE seats and butterfly type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85⁰C.
Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of angled spherical valves with chromium plated brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, chome plated brass balls and EPDM O-rings. Connection to be used with copper pipe EN1057. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with brass bodies, ball and PTFE seats and incorporates two single check valve assemblies (verified by test, suitable for backflow protection against Fluid Category 3). Compression models are for use with BSEN 1057 copper pipe. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass, nickel plated brass, brass or DZR brass bodies and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of in-line angled or ‘T’ type spherical valves with chromium plated brass and brass ball. Models have screwdriver, lever or butterfly operating members. Maximum working pressure 10.0, 16.0 or 25.0 Bar. Maximum operating temperature 85° or 99°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Screw down stop valve, with a brass body and handwheel operating member. Maximum working pressure 10 bar. Maximum operating temperature 23°C
Range of screw down stop valves with brass bodies. All models incorporate a wheel type operating member. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
'Sigrafine® EK2239, EK2200, EK2230 & EK2240'. Grey coloured, compression moulded, phenolic resin impregnated carbon rings. For use with water up to 85°C.
'4.R50760000-01'. Beige coloured, sintered, ceramic rotor shaft. For use with water up to 85°C.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 864'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/11/2024'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM III/B-SR - Ramco Slag'. Factory applied, grey coloured Portland Slag Cement. Mix cement:sand:water in a 0.6:1.0:0.22 weight ratio and apply as per manufacturer's work instructions 'WP-08-05 I, issue no. 04, Rev. 0', dated '22.08.2024'. Cure for 24 hours at 27°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'GMSM01' dated '2024.11.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Wudu brand-NF 131118'. Factory applied, black coloured, two-component, water based epoxy coating. Mix in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V2', dated '20240821'. Cure for 1 hour@50°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dicoat 60 EX Blue'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's user instructions 'SPL/R&D/TTD/UI/007', version '01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPONICS WP-NS (No. 20170209)'. Factory applied, dark grey coloured, two-component, solvent free epoxy resin coating consisting of a base and hardener. Mix base and hardener in a weight ratio of 7:3 and apply as per Product Data Sheet ‘1838-K’ dated February 2017. Cure for 168 hours@30°C, then 168 hours@60°C and 'rest' for 168 hours before use. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001'. Factory applied, blue coloured epoxy coating. Apply as per manufacturers technical data sheet dated 9th November 2015. Cure for 2 minutes, 30 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'90000 KANEPOX SF-A'. Factory applied, two-part, cream or red coloured epoxy coatings consisting of component A and component B. Mix and apply as per data sheet ‘Rev. No. 01’ dated January 2024. Cure for 7 days@23°C. The cream coating is for use with water up to 50°C. Between February 2024 and August 2024, the red coating is for use with water up to 23°C. From September 2024 the red coating is for use with water up to 50°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JSGL-BFSC III A (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pulron 101 Aqua'. Factory applied, blue coloured PE coating. Apply as per manufacturer's instructions application guide dated 07.02.2018. Cure for 10 minutes@200°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-201'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ARC S2 (E)’. Factory applied, two component epoxy ceramic coatings, available in green and grey colours. Mix, apply and cure in accordance with Application Instructions '085031EU' dated 01/25. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that are included in Application Instructions '085031EU' dated 01/25. If the mixing and/or curing conditions are varied from those specified in these instructions then the material is not covered by the scope of the approval.
'JERLAC Two Pack Epoxy Beige-740'. Factory applied, two-part, beige coloured epoxy coating. Mix in a 3:1 volume ratio and apply as per manufacturer's data sheet issue number '01', dated '10.01.2024'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW– JAL (OPC-TICL)'. Factory applied, grey coloured Ordinary Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (SRPC-DCL)'. Factory applied, grey coloured Sulphate resistant Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (BFSC-JSL)'. Factory applied, grey coloured Blast furnace slag cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20' and apply as per. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM I-SR3 – Parasakti SRPC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement. Mix cement, sand & water in a 0.6 : 1.0 : 0.22 mass ratio and apply as per work instructions 'WP-08-05 I', issue '04', rev. '0' dated '22.08.2024. Cure for 24 hours@27°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Hempadur 35530 System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘Hempadur 35530 red (51320) and Hempadur 35530 grey (10500)’. ‘Hempadur 35530 red (51320)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘Hempadur 35530 grey (10500)’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet dated October 2024. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Dyopox PTW Red'. Factory applied, red coloured, two-component epoxy coating. Mix base and hardener in a 2:1 weight ratio and apply as per manufacturer's datasheet 'R3 issued 2024'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KLINGERSIL® C-4240'. Off-white coloured NBR/fibre gasket material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'KLINGERSIL® C-4430'. NBR/fibre gasket material, which is green coloured one side and white coloured the other, manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Busan-Tank'. Light grey coloured, hot pressed GRP panel. For use with water up to 50°C.
'Hylon N1040 H2 BK397 W & Hylon N1030 H2 BK397 W'. Black coloured, injection moulded, glass fibre filled polyamide materials. For use with water up to 60°C.
'LCPA-G(1)06 HMNC001'. Natural, (appears off-white), injection moulded, glass fibre filled nylon material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% (05) - 65%. For use with water up to 85°C.
'27GFT'. Natural (appears white), extruded PA66+30GF material. For use with water up to 85°C.
'ULTRAMID® A3EG10 FC AQUA BLACK23285'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Celanex 3300-2FC EF2001 natural'. Natural (appears cream coloured), injection moulded PBT material. For use with water up to 60°C.
'Celanex 2002-2FC EF2001 Natural'. Natural (appears white), injection moulded PBT material. For use with water up to 60°C.
'Crastin FGS600F10 NC010 (White)'. White coloured, injection moulded, Polybutylene Terephthalate material. For use with water up 60°C.
'Ecoleader® EL-4300'. Dark Yellow coloured (transparent), Vinyl Ester Resin material manufactured by casting moulding process. For use with water up to 60°C.
'Ecoleader® EL-4060'. Yellow coloured (transparent), Unsaturated Polyester Resin material manufactured by casting moulding process. For use with water up to 50°C.
'AASTER 962'. Brown coloured (translucent), injection moulded Polyester resin material. For use with water up to 50°C.
'Thermocomp JF006E-BK1B633'. Black coloured, injection moulded Polyethersulfone material. For use with water up to 85°C.
'PE-B-01 Inlet Pipe'. Blue coloured, injection moulded Polyethylene pipe. For use with water up to 85°C.
'PE-R-02 Outlet Pipe'. Red coloured, injection moulded Polyethylene pipe. For use with water up to 85°C.
'PE-R-01 Thermocouple Protection Tube'. Red coloured, injection moulded Polyethylene tube. For use with water up to 85°C.
'Water Guide P96400-005'. Beige coloured (opaque), injection moulded PPO component. For use with water up to 65°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'PP-01 Magnesium rod plastic joint'. White coloured, injection moulded Polypropylene Magnesium rod plastic joint. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'UPS SEAL-FLEX TAPE'. Extruded, self-fusing silicone rubber tapes available in Black and Red colours. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'F802'. White coloured, extruded PTFE material. For use with water to to 85°C.
'E9053AA 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'EP50/1 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 50. Tested in-radius 1.7mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
SI-55678 (shore hardness 50), SI-65678 (SH 60), SI-75678 (SH 70) & SI-85678 (SH 80) natural ‘O’ rings. SI-52109 (shore hardness 50), SI-62109 (SH 60), SI-72109(SH 70), SI-82109 (SH80) red coloured ‘O’ rings. SI-51501 (shore hardness 50), SI-61501 (SH 60), SI-71501(SH 70) & SI-81501(SH 80) blue coloured ‘O’ rings. Natural (appears white coloured), red or blue coloured, compression moulded silicone rubber ‘O’ rings. Shore hardness between 50 shore A and 80 shore A. Tested in-radii sizes between 0.5mm & 2.5mm. For use with water up to 85°C.
'Silicone-01 Heater Seal Ring'. White coloured, compression moulded Silicone ring. Shore hardness 70. Tested in-radius size 3.4mm. For use with water up to 85°C.
'Silicone-02 Sealing Gasket'. Natural (appears white), compression moulded Silicone gasket. Shore hardness 70. Tested in-radius size 1.25mm. For use with water up to 85°C.
'LOCTITE® 2700™'. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Range of stop valves with plastic bodies. The valves incorporate a built in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with model SVSM66MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only
'+GF+ PVC-C'. Grey coloured, injection moulded PVC-C fittings. For use with water up to 60°C.
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assembly. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator, and products are supplied with interconnecting stainless steel braided silicone lined flexible hose assemblies. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. For use with cold water only
The range of WC cisterns incorporating a BS 1212-4:2016 side entry or bottom entry float operated inlet valve providing a Type AG air gap arrangement and a flush outlet valve operated via a push button assembly for either full or reduced flush. Maximum operating pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5) with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. The supply hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of flow sensors with plastic bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
DC type pipe interrupter with a permanent atmospheric vent (DZR brass body) incorporating a flow regulator at the inlet and brass shroud. Maximum working pressure 6.0 bar. Cold water use only.
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Range of non-verifiable double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. The products incorporate a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of stainless steel calorifiers. Max working pressure 10 bar. Max operating temperature 90°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass body) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of ½ turn ceramic disc headworks with plastic bodies (middle position off, quarter turn either way for hot or cold). For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of ceramic cartridge headworks with a plastic body. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85 °C.
Ceramic cartridge headwork with a plastic body. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VS11-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS11-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ20 | ½” BSP | 10 bar | 85 °C | PPI 20 | Body | No | Non-rising spindle | Not Applicable | Not Applicable | ||
| VS5412-BZ24 | ½” BSP | 10 bar | 85 °C | PPI 24 | Body | No | Non-rising spindle | Not Applicable | Not Applicable |
The difference between models are the splines only, one has 20 and the other has 24.
Single hole, single outlet, fixed, combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. Model 24.341.xxx is supplied with lever operated pop up waste (not verified by test). Maximum working pressure 10 Bar. Maximum operating temperature 60°C.
Single hole, single outlet fixed combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure - 5 Bar Maximum operating temperature - 60 °C
Range of single-hole, single outlet, (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Model 33500671 is supplied with a lever type pop-up waste – not verified by test. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CAP BASNW C | Chrome | 15mm compression | 5 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193838 X XXX | VARIOUS | 1/2" BSP | 10 bar | 65 °C | PPI | Body | No | Ceramic cartridge | C Clamp | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever type operating members. The spout outlet incorporates plastic flow straighteners. Products are supplied with click-type pop-up wastes (verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SAI BAS C | Chrome | M10 X 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Aerator |
Single-hole, single outlet (swivel) combination tap assembly (chromium plated brass body), incorporating quarter turn ceramic disk headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Single-hole, single outlet (swivel) combination tap assembly (chromium plated brass body), incorporating quarter turn ceramic disk headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
A range of single-hole single outlet swivel combination tap assemblies with brass bodies (chromium plated). Incorporating ceramic cartridge headworks with various operating members. The spout outlets on some models incorporate a plastic aerator. Maximum working pressure - 10 bar. Maximum operating temperature - 60°C.
Range of wall mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 bar. Maximum operating temperature: 70°C.
Range of two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal or plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet fixed combination tap assemblies (chromium plated brass bodies) incorporating a ceramic cartridge headwork with single lever operating members. Both inlets incorporate approved check valve cartridges. However, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic flow straightener, and the products are supplied with metal backnuts. All models incorporate a straight connector servicing valve located on both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with dome operating members. The spout outlets incorporate plastic aerators or flow straighteners. The product is supplied with metal back nuts. Maximum working pressure – 10.0 Bar Maximum operating temperature - 70 °C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 70 °C
Range of two hole, single outlet, fixed, wall mounted shower valves (chromium plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members. The products incorporate a plastic aerator on the outlet and the inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. All models incorporate a straight connector servicing valve located on both inlets. Maximum working pressure 5 Bar Maximum operating temperature 60°C
Wall mounted, concealed, two-hole single outlet (fixed) combination tap assembly with a brass body (various finishes), incorporating a ceramic cartridge headwork with a single leaver operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193806 X XXX | Various | ¾” BSP | 10 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3 The spout outlet incorporates an aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Two hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating non rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 60°C
Range of wall mounted spout outlets (brass bodies - various plated) incorporating a plastic aerator. Maximum operating temperature: 60 °C
Deck mounted spout outlet with chromium plated brass body incorporating a plastic aerator. Maximum operating temperature 60°C.
Wall mounted spout outlet, (chromium plated brass body) incorporating a plastic aerator. Maximum operating temperature 60°C.
Range of Grohe ‘Atrio’ wall mounted spout outlets (brass bodies - various finishes), the outlet incorporates a plastic aerator. Maximum operating temperature: 60°C
Expansion vessel with a stainless-steel body. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
The products incorporate two check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3), a pressure reducing valve adjustable between 1.0 bar and 3.0 bar (but pre-set at 2.5 bar for 523.815 model and 1.4 bar for the 523.816 model). The product incorporates a push type valve which allows water to flow when operated until the required pressure is achieved. There is a drain port below the push valve piston chamber. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum supply pressure 10.0 bar. Maximum operating temperature 80°C.
Range of filter heads with plastic bodies. Models with threaded connections incorporate a non-return valve (not suitable for backflow protection). Maximum working pressure 8.0 bar. Cold water use only.
Inline filter with plastic body. Maximum working pressure 5.0 bar. Cold water use only.
Range of RidgeLock™ sets consisting of Ridgeline corrugated stainless steel tubing adapter sealing rings connected using EN 1254-2 brass fittings to achieve a compression connection. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (Unipress MLCP ) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Supreme range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of stainless steel (SS316L) pressfit fittings with EPDM ‘O’-rings for use with stainless steel pipe (manufactured to EN10312). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper end feed fittings for use with copper tube to EN 1057. For above and below ground use. Maximum working pressure: 6mm-54mm 16.0bar, 64mm-108mm 10.0bar. Maximum operating temperature 85°C
WC dual flush valves with a plastic body and incorporates an internal overflow. Cold water use only.
Shower wastewater heat recovery units with a copper body and twin wall separation. Maximum working pressure 10.0 Bar. Maximum operating temperature 45°C.
Range of water meters with plastic bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of electromagnetic water meters with stainless steel bodies and natural rubber liners. Maximum working pressure 10.0 Bar Maximum operating temperature 50.0°C
Range of in-line single jet water meters with brass bodies. Products incorporate plastic strainers. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 85.0°C.
Range of ultrasonic water meters with brass bodies. The products incorporate a motorised butterfly valve on the outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line water meters with brass or plastic bodies. Models with a minimum length of 130mm and a maximum operating temperature of 50°C are supplied with an optional, non-return valve to be fitted by the installer (not suitable for backflow protection). Maximum working pressure 16.0 bar. The meters can be supplied with a maximum operating temperature of 50°C or 70°C.
Range of water meter manifolds incorporated into a meter chamber. The inlet of all models incorporates an isolation valve and an approved check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection. MK7000003003 is for use with MDPE plastic pipe (manufactured to BS EN 12202-1:2011). Maximum working pressure 12.5 bar. Cold water use only.
Water meter manifold with a gunmetal body. The product incorporates a non-return valve (not suitable for backflow protection) and a spherical valve on the inlet. Maximum working pressure 16.0 bar. Cold water use only.
Mixing valve incorporating a brass body and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure10.0 bar. Maximum operating temperature 65°C.
Range of click type, pop-up wastes with metal bodies. Maximum operating temperature 60.0°C
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of booster pumps with stainless steel bodies, impellers and non-return valves (not suitable for backflow protection) at the inlets. Maximum working pressure: 6.0 Bar. Cold water use only.
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 4.0 bar. Maximum operating temperature 85°C
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C
Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C
Concealed, ceiling mounted installation sets and shower outlets. The inlets incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of shower handsets (plastic bodies – various finishes), incorporating a plastic flow regulator on the inlet. Open outlet use only. Maximum operating temperature: 60 °C
Range of overhead shower outlets with brass bodies (various finishes). The inlet incorporates a plastic flow regulator and stainless steel strainer. Maximum operating temperature 60°C
Range of shower handsets incorporating chromium plated ABS plastic bodies. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60.0°C
Range of shower handsets with plastic bodies incorporating an integral filter. The inlet incorporates a combined washer and a strainer, plastic flow regulator and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C. Open outlet use only.
Range of (chrome plated) plastic shower handsets, each supplied with five (optional) plastic flow regulators (x2 blue, light green, dark green and grey). Maximum operating temperature 60°C.
Chrome plated plastic shower handset incorporating a flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of overhead showers with plastic body (various finishes). Overhead shower inlets incorporate a stainless steel strainer Maximum operating temperature 60°C.
Shower outlet kit, consisting of chromium plated ABS shower handset and PVC lined shower hose. The kit is also supplied with a riser rail and handset retainer. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall and ceiling overhead shower outlets with chromium plated brass bodies. The inlets incorporate a plastic flow regulator. Maximum operating temperature 60°C.
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of wall mounted bib taps (chromium plated brass), incorporating a non-rising spindle headwork with a cross top operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Wall mounted, single hole, single outlet (fixed) bib tap (chromium plated brass), incorporating a non-rising spindle with a single lever operating member. The outlet incorporates a metal flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M0602 X XXX | various | 3/4" BSP | 10 bar bar | 85 °C | PPI | Body | No | Non-rising spindle | Metal Backnuts | Open Outlet |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 6.0 Bar Maximum operating temperature 60 °C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 6.0 Bar Maximum operating temperature 60 °C.
Range of wall or floor mounted, self-closing taps (chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60⁰C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure 6.0 Bar Maximum operating temperature 60 °C.
Range of flexible shower hose assemblies comprising of a PVC inner, multi-layered hose (silver external appearance), with silicone ‘O’-rings and washers. Maximum operating temperature: 60°C. Open Outlet use only.
Range of stainless steel braided, PEX lined, flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided PEX lined flexible hose assemblies. The captive nut and M15x1 end connections incorporate a washer. The M8x1, M10x1 and M12x1 end connections incorporate an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of EPDM lined hoses with grey PVC outer layer. Maximum working pressure: 16 bar. Maximum working temperature: 60°C.
Range of stainless steel braided EPDM lined flexible hose assemblies. The captive nut and M15x1 end connections incorporate a washer. The M8x1, M10x1 and M12x1 end connections incorporate an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided flexible hose assemblies incorporating EPDM inner and plastic (BFSFH12-EE80/150) or brass (BFSFH19-EE60) captive nut end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Unvented hot water cylinder for domestic hot water 180 litre and buffer vessel 70 litre comprised of stainless steel main body, a stainless steel buffer cylinder 7 bar max working pressure max operating temperature 90°C. The cylinder is fitted with a T & P valve and supplied with an inlet control group consisting of pressure reducing, a pre-set expansion relief and incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Max working pressure 7.0 Bar. Max operating temperature 90°C.
Range of stainless steel hot water buffer tanks. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
Range of unvented storage cylinders. The secondary circuit is fitted with a temperature and pressure relief valve set at 7.0 bar at 90˚C and an expansion relief valve set at 6.0 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Also Supplied with an expansion vessel and tundish. Maximum working pressures: Primary circuit: 5.5 bar Secondary circuit: 6.0 bar Solar circuit:6.0 bar Maximum operating temperature 85.0°C
Range of 2, 3, 4, 5, 6 and 7 port manifold assemblies with brass bodies incorporating spherical valves with lever type operating members. The port compression connections are for use with copper pipe to EN1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 95.0°C
Range of air venting valves with blue epoxy coated ductile iron bodies and stainless steel float. Maximum working pressure: 16.0Bar Maximum operating temperature: 60°c
Concealed, wall mounted, manual shower blending valve incorporating a brass body (various finishes) with ceramic cartridge headwork with a single lever operating member. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60 °C.
Range of wall mounted, manually operated, shower valves (chromium plated brass), incorporating a ceramic cartridge headwork controlling both flow and temperature using a single lever operating member. The products (except for S suffix models) are supplied with ¾” x ½” offset union adaptors which incorporate a servicing valve. The inlets of models containing EP include plastic filters and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. All other models incorporate plastic flow regulators on each inlet and an approved single check valve cartridge on the outlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted concealed thermostatic blending valves, (brass bodies – various finishes). Model (TVT126001000xx) incorporates a quarter turn ceramic disc headwork. Model (TVS126003000xx) incorporates a two-way ceramic disc diverter headwork. Temperature is controlled independently via a thermostatic mixing cartridge that incorporates a manual override button. Both models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar or 10.0 Bar (see models). Maximum operating temperature 60°C.
Range of thermostatic bar shower mixers, incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type of operating member. The temperature is controlled independently via a thermostatic mixing cartridge incorporating a manual override button. Inlets incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models ZI SHXSMCT C & ZI SHXSMCTFF C are supplied with a shower hose, handset and a riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of thermostatic bar shower mixers, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with a dome type operating member. Temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. The Inlets incorporate stainless steel strainer washers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model (FZ SHXVOCTFF C) is not supplied with a shower hose, shower handset and a riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of concealed thermostatic shower mixers, (brass bodies - various finishes). The flow is controlled by either a quarter turn ceramic disc headwork (model HOX1000Rx) or a three-way manual diverter (2 on, 1 off position) (model HOX1500Rx) with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member. The inlets incorporate approved single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5 Bar. Maximum operating temperature 85°C.
Range of wall mounted, concealed thermostatic shower valves (brass bodies – various finishes) incorporating a 2 way or 3 way diverter controlling the flow to multiple shower outlets using a dome type operating member. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with a dome type operating member. The inlets incorporate approved single check valve cartridges however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of T-type blending valve with brass bodies and thermostatic cartridges. Compression models are for use with copper pipe manufactured to EN1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 75°C.
Range of wall mounted, exposed, thermostatic shower valves (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork which diverts the flow between the shower outlets using round or square operating members. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button also using round or square operating members. Both inlets incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of thermostatic bar shower mixers, incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type of operating member. The temperature is controlled independently via a thermostatic mixing cartridge incorporating a manual override button. Inlets incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with a shower hose, handset and a riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of thermostatic bar shower mixers, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with a dome type operating member. Temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. The Inlets incorporate stainless steel strainer washers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of butterfly valves with black epoxy coated ductile iron bodies & aluminium bronze discs. The closing mechanism can be controlled by lever or handwheel (via gearbox). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of butterfly valves with black epoxy coated ductile iron bodies & aluminium bronze discs. The closing mechanism can be controlled by lever or handwheel (via gearbox). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of lever operated butterfly valves with blue epoxy coated cast iron bodies, stainless steel discs and EPDM ‘O’ rings and seals. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of concealed, 2-way manual diverter valves incorporating a brass body. To be installed with 59556 000070 IXMO installation unit. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C.
Range of below ground (screw down type) fire hydrants with coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies. Maximum inlet supply pressure 8.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome plated DZR brass bodies, for use with copper pipe (manufactured to BS EN 1057). Supplied with a pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of pilot operated, pressure reducing valves epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, spherical valves and a needle valve. Outlet pressure setting is adjustable in the range of 1.0 bar to 12.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.
Pressure relief valve (pre-set at 3.0 bar) with a brass body. The valve incorporates a manually operated easing gear. Maximum operating temperature 110°C.
Range of latching or normally closed solenoid valves with plastic bodies and a silicone diaphragm. The products incorporate a plastic flow regulator on the outlet. The R197 model has a Ø13mm ID outlet for customers to insert their own outlet connections into. Maximum working pressure 10.0 Bar Cold water use only.
Range of straight, angled, tee and Y shaped isolation valves incorporating brass bodies, NBR ‘O’-rings or PTFE seats depending on model variant. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Floreg’ range of in-line lever operated spherical valve with a DZR brass body (brushed chromium plated) and ball. The product incorporates a stainless-steel mesh strainer and a flow regulator. Compression connection to be used with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a brushed chrome plated brass body, brass ball and PTFE seals. . Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves having brass, DZR brass or stainless-steel bodies and lever type operating members. For use with stainless steel pipe (EN10312) or copper pipe (EN1057). Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C.
Range of spherical valves, with brass bodies (either nickel plated or chromium plated) and a chromium plated brass ball. The products can be supplied with various operating members (see model). The products are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of spherical valves, with DZR brass bodies and chromium plated brass balls. The products can be supplied with various operating members (see model). Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 80 °C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Gate valve with a blue epoxy coated ductile iron body and an EPDM lined disc, with a non-rising spindle operating mechanism. Maximum operating temperature: 80°C. Maximum working pressure: of 16.0bar.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models SCM020000535, SCM025000536, SCI100000533, SCM025002164 & SCM032002165 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range rising spindle screw down stop valves with gunmetal bodies and T-type operating members. Models 41020, 41025, 41032, 31050 models are to be used with PE80 pipe manufactured to EN 12201. Maximum working pressure: 12.5 Bar. Maximum operating temperature: 23°C.
Range of electrolytic scale inhibitors incorporating copper bodies. For use with copper pipe complying with BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
Electrolytic inline limescale reducer with a zinc plated brass body and a copper coil. Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Continuous soft water, ion exchange, hydraulically driven water softener (salt regenerated) for domestic use, incorporating LLDPE tubing. Operation is by an ion exchange resin filed plastic pressure vessel, with integral salt cabinet and timer/manual regeneration control. The appliance incorporates single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature Cold water only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'ULTRAFORM® N4320 003 AT UNCOLORED'. Natural (appears white), injection moulded POM material. For use with water up to 85°C.
'REVIMEN Bituminous Paint'. Factory applied, black coloured Bituminous paint. Apply as per manufacturer's TDS/Application Application Method 'AM25001', issued 'March 5, 2025'. Cure for 8 hours@25°C at a relative humidity of less than 85%. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ResiGard APUA (NT) Coating'. Factory applied, grey coloured (once mixed), two-component coating. Mix and apply as per Technical Data Sheet ‘PDS/RG37/Ver15/01/25’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Greentech 5000'. Factory applied, blue coloured Epoxy powder coating. Apply as per manufacturer's 'GRHK/QES GL 2025' and cure for 10 minutes@200°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PA6059 Pure Polyester Powder Coating'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions 'file no. FP180515 version 2' dated May 25, 2018. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOD-E-2024/1'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions 'T264', revision '00', dated '16.07.2024'. Cure for 25 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hansung M&S GRP Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 60°C.
'UNISILKON TK 002/1000'. Clear lubricant, to be applied as per manufacturer's instructions. For use with water up to 65°C.
'Sinopec Water Pipeline Joint Lubricant (Si) (product code: 509164)'. Clear, translucent silicone base lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'MS Schramberg Sintered Barium Ferrite (10-1176001)'. Dark grey coloured Sintered Barium Ferrite ring component. For use with water up to 85°C.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
'ULTRAMID® T7300EG10 FC Aqua BK23285'. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'PLUSTEK PAT302PWG50BK10'. Black coloured, injection moulded, glass-fibre reinforced polyamide material. For use with water up to 85°C.
'Polimal 122-2 AWTP' (beige coloured) & 'Polimal 1094 AWTP-1' (amber coloured). Contact moulded, unsaturated polyester resin materials. For use with water up to 23°C.
'Sirester EC 0995/AT'. Pale orange coloured, unsaturated polyester resin material manufactured by filament winding. For use with water up to 23°C.
'Omanplast HDPE Pipe'. Black coloured (with blue external stripes), extruded HDPE pipe (manufactured in Muna Noor Manufacturing & Trading LLC, Sohar & Muna Noor Manufacturing & Trading LLC, Rusayl, Oman). For use with water up to 60°C.
'Ori-Plast Electro-Fusion Fittings'. Black coloured, injection moulded PE 100 Electro-Fusion Fittings. For use with water up to 65°C.
'AMIANTIT HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 50°C. Please note that only pipes marked with 'HE3490' are covered by the scope of the approval.
'ANTON HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 80°C.
'Shield HDPE-100 Pipe' (extruded) and 'Shield HDPE-100 Fabricated Pipe' (extruded then fabricated). Black coloured, HDPE pipes. For use with water up to 85°C.
'Shield HDPE-100 Moulded Fittings'. Black coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'Yildiz Polietilen Electrofusion and Spigot Fittings'. Black coloured, injection moulded HDPE Electrofusion and Spigot fittings. For use with water up to 60°C.
'TEGA PE100-RC Blue fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'THERMOTECH HDPE Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'Techniplast PE100 Pipes'. Black coloured (with blue stripe), extruded PE100 pipes. For use with water up to 60°C.
'NORYL WM330G-73701 (black), NORYL WM330G 7G8B4911 (grey) & NORYL WM330G-4G8B5291 (beige)'. Injection moulded PPE-PS materials. For use with water up to 85°C.
‘NORYL’ black coloured, grey coloured or beige coloured, injection moulded PPE + PS materials. FE1410PW – 73701. FE1520PW – 73701. FE1630PW – 73701. FE1740PW – 73701. FE1520PW - 4G8B5291. FE1630PW - 4G8B5291. FE1410PW – 7G8B4911. FE1520PW – 7G8B4911. FE1630PW – 7G8B4911. FE1410PW-4G8B5291, FE1740PW-4G8B5291 & FE1740PW-7G8B4911 were added to the approval in April 2025. For use with water up to 85°C
'TERRATHERM Fittings'. Green coloured, injection moulded PP-R fittings. For use with water up to 70°C.
'Hostalen PP H4122 103220'. Polypropylene material for injection moulding and compression moulding. For use with water up to 23°C.
'GW 160m'. White coloured (opaque), thread sealant. For use with water up to 85°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'558CM'. Black coloured, transfer moulded EPDM O-Ring. Shore hardness 60. Tested in-radius size 0.87mm. For use with water up to 85°C.
'B1-4651'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 60. Tested in-radius size 4.6mm. For use with water up to 23°C.
'E7001Z59-10 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'Precision782628 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E633'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'N146 Sealing Cap and Bellow'. Black coloured, injection moulded nitrile rubber sealing cap & bellow. Shore hardness 70. The cap has a tested in-radius size of 0.6mm and the bellow has a tested in-radius size of 1.0mm. For use with water up to 23°C.
'N70N06G Seal'. Black coloured, injection moulded NBR seal. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C. When processing an application for WRAS Product Approval, this is the only shape of component covered by the approval.
'N8018AA'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'01/N50 VMQ, 01/N60 VMQ & 01/N70 VMQ White. 01/M50 VMQ, 01/M60 VMQ & 01/M70 VMQ Red. 01/L50 VMQ, 01/L60 VMQ & 01/L70 VMQ Blue'. Range of injection moulded silicone rubber `O` rings and gaskets available in white, red & blue colours. Shore hardness between 50 & 70. Tested in-radii size of between 1.0mm and 2.0mm. For use with water up to 85°C.
'Loxeal 83-50, 83-50 T, 83-50L, 83-50HT & 83-50AL'. Green coloured anaerobic adhesives. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Weld-On 705 ECO Clear PVC cement'. Clear solvent cement. Apply as per manufacturers technical data sheet '705 ECO-09-2024'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum operating pressure 10 bar. Maximum operating temperature 40°C.
'XRRA 410B GR1500'. Grey coloured, injection moulded U-PVC material. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cisterns with a BS 1212- 4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a manually operated dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3). The threaded shower connection incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar. Maximum operating temperature - 60 °C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
Wall mounted two hole, single outlet (fixed) combination tap assembly with chromium plated brass body. Incorporating a ceramic cartridge headworks with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) The spout outlet incorporates a plastic aerator. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: 10 Bar. Maximum working temperature: 60°C.
Concealed 2-way or 3-way brass body diverter valve (see models) with or without shut off mechanism (see model) and various trim sets and operating members (see model). Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
Concealed self-cancelling control with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). (brass body) with a variety of operating member styles. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 60.0°C.
Range of CA-b backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of CAb backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Filling link with manual or automatic tap. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies, NBR ‘O’-rings and stainless-steel strainer. For insertion into specifically dimensioned bores. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of ceramic cartridge headworks with plastic bodies, EPDM gaskets and NBR O-rings. The products are for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of non-rising spindle headworks with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies. The 12333004-001 model is a 2-way ceramic disc diverter headworks. The 12333006-001 model is ¼ turn. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) pull down spray combination tap assemblies (brass bodies – various finishes), model (62861-01X) incorporates quarter turn ceramic disc headworks, models (62931-00X & 62932-00X) incorporate ceramic cartridge headworks, all with single lever operating members. The outlet incorporates a plastic aerator. Model (62861-01X) incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 231827 | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | ||
| 257582 | Black | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate |
Range single-hole, single outlet fixed combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. ‘AB’ models spouts incorporate plastic aerators. Maximum working pressure 5 bar. Maximum operating temperature 70°C.
Range of single-hole, single outlet, fixed combination tap assemblies (brass body – various finishes), incorporating caramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar Maximum operating temperature 70°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MIO BAS C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| HMS MIO BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener | |
| CN SPH BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
HMS MIO BASNW C - (selling code for Homeserve without Waste) CN SPH BASNW C - (selling code for Crest without Waste)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| BQVEC BAS C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener | |
| VT2 BASNW C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC BSNK C MT | Chrome | 15mm Copper Tail | 7.0 bar | 65 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet | |
| VAC BSNK WHT | Chrome | 15mm Copper Tail | 7.0 bar | 65 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet |
Range of deck mounted; two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model) incorporating quarter turn ceramic disc headworks with dome type (CAM-137-XXX models) or single lever (all other models) operating members. The spout outlet of the EDI-137-CP & IND-ED137-XXX models incorporates a plastic aerator, all other models incorporate a plastic flow straightener. The products are supplied with brass back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Deck mounted; two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with brass back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, wall mounted, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 231829 | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF BB | Brushed Brass | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF C | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| HOU BF BLK | Black | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| RP3 HOU BF C | Chrome | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| 257583 | Black | ¾" BSP (M) | 5.0 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FRZ BF C | Chrome | 3/4" BSP (M) | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| BQVEC BF C | Chromium | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| VT2 BF C | Chromium | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193805 X XXX | VARIOUS | ¾” BSP | 10 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks with cube type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of wall mounted, concealed thermostatic basin mixing valves with brass bodies. Temperature is controlled via a thermostatic cartridge and flow is controlled by solenoid valves actuated by an infrared sensor. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted spout outlets, (brass bodies - various finishes) incorporating a plastic aerator. Open outlet use only. Maximum operating temperature 60°C.
‘MUFA’ and ‘MUPA’ ranges of expansion vessels with epoxy coated bodies. ‘MUFA’ models have a maximum working pressure of 8.6 bar. ‘MUPA’ models have a maximum working pressure of 10.0 Bar. Cold water use only.
Range of in-line water filter cartridges with plastic bodies. Maximum working pressure 8.0 bar. Cold water use only.
Range of DZR Brass and Bronze compression fittings for use with VIALLI PEXa pipe. Maximum working pressure 10.0 bar. Cold water use only.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘APL’ & 'AP' ranges of brass press fittings for use with ‘APE Multylayer' pipe. Connection is achieved via TH or U profile press jaws. AP range, only TH profile; APL range, TH and H profile; TH and H profile from DN 16 to DN32; TH for DN40, DN50 and DN63. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass compression fittings for use with PEX pipe (manufactured to ISO 15875). Maximum working pressures: 16mm and 20mm sizes: 25.0 bar, 25mm sizes: 15.0 bar. Cold water use only.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Dual flush WC syphon, with a polypropylene body and stainless-steel link for use with WC flushing cisterns. Cold water use only.
Range electric, instantaneous, open outlet, mains water heaters. Maximum working pressure 6.6 bar. Maximum operating temperature 70 ˚C.
Electric instantaneous water heater with a plastic casing. Flow is controlled via a solenoid valve operated by an infrared sensor. Temperature is controlled by a dial on the front of the unit. The product incorporates a swivel arm outlet from the base. Maximum working pressure 3.0 bar. Maximum operating temperature 48˚C. Cold supply only.
Range of under-sink, electrically heated vented water heaters (cased and insulated). Maximum operating temperature 98˚C
Range of heat interface units incorporating a heat exchanger, flow sensor, spherical valve and shock arrestor. The heating circuit incorporates a pressure relief valve set at 3.0 bar. Maximum working pressure & operating temperature: Primary circuit is 16.0 bar & 90°C. Domestic hot water circuit is 10.0 bar & 65°C. Heating circuit is 2.5 bar & 80°C.
Range of in-line ultrasonic water meters with brass bodies and plastic housing. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of ultrasonic water meters with brass bodies and plastic transducers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Direct coupler (brass with a range of finishes). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of Fastec® F13 and Fastec® F14 fittings for use with Fastec® manifold assemblies, incorporated with brass bodies and EPDM O-rings. To be used with copper pipe complying with BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of spherical valves with a DZR brass body and lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, deck mounted flow control, (brass bodies - various finishes) incorporating a ceramic cartridge headwork and lever type operating member. Maximum working pressure 5 bar. Maximum operating temperature 60°C.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O` rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Please refer to model for maximum operating pressure. Maximum operating temperature 65°C.
Range of combined storage and booster sets, incorporating a cold-water storage cistern, submersible pump, solenoid valve or alternative actuated ball valve, non-return valve (not suitable for backflow protection), isolation valves and expansion vessel. Maximum working pressure 10.0 bar. Cold water use only.
“TP/TPE series 100” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure: Cast iron models: 16.0 bar, Stainless steel models: 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.
“TPE 2 & TPE3 series” single stage centrifugal pumps, incorporating cast iron (with black coloured electrocoating) or stainless-steel bodies and plastic impellers. Maximum working pressure 10.0 bar. Maximum operating temperature: Cast iron models: 60°C, Stainless steel models: 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HS170 XXX | Various | 1/2" BSP | bar | 85 °C | PPI | Body | No | Fixed Head, |
XXX Denotes the following: First, second & third XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Ceiling mounted shower outlet (chromium plated) with a concealed ceiling installation box. The inlet to the concealed ceiling installation box incorporates a flow regulator and a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use. Maximum operating temperature 70.0°C
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless steel mesh strainer. Maximum working pressure 20 bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 BIB C CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener | |
| VAL2 BIB C 6 CD | Chrome | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Handle | No | 1/2 Turn ceramic disk | Not Applicable | Flow Straightener |
Range of drain taps with brass (or DZR brass, see models) bodies and non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of wall mounted hose union bib taps incorporating a rising spindle headwork with a T - handle operating member. Products have a brass body. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps are supplied with an optional flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
'ELS108'. Dual layered, extruded PVC hose incorporating EPDM washers. Maximum working pressure 10.0 Bar Cold water use only.
Range of stainless steel braided, nylon braided, double locked (metal outer) or reinforced (see model), PEX/HTRPE lined flexible hose assemblies with EPDM washers and O rings. Available with a variety of finishes or end connections (see model). Maximum operating temperature 85°C.
Range of stainless steel inter-locked shower hoses incorporating PVC linings in various finishes. Maximum operating temperature 65°C.
Stainless steel braided EPDM lined flexible hose assembly with EPDM washers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: Primary circuit: 6.0 Bar Secondary circuit: 5.5 bar Maximum operating temperature: 85.0°C
Range of 2, 3, 4, 5 or 6 port manifold assemblies with brass bodies. The products incorporate a spherical valve with a plastic ball on either the inlet or on each outlet (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of air venting valves with bronze bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, manually operated blending valves with brass bodies (various finishes) and ceramic cartridge headworks controlling both the flow and temperature with a single lever operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted concealed, shower valves (brass bodies – various plated trim sets) incorporating a ceramic cartridge headworks with single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). Maximum operating pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, digitally controlled thermostatic blending valve with a 1, 2 or 3 outlets, incorporating a plastic body, the flow and temperature is controlled via a digital user interface. Products incorporate a built-in pump and a solenoid valve. Maximum working pressure 1.0 Bar Maximum operating temperature 65.0°C
Wall mounted, bar type thermostatic blending valve, (brass bodies - various finishes), incorporating a half turn ceramic disc for manually diverting the flow between the shower handset, on off position, and the overhead shower with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a manual override button with a dome type operating member. The product is supplied with an overhead shower head, shower hose and handset. Each inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless-steel strainers. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted concealed thermostatic shower valves (brass bodies – various finishes) incorporating either quarter turn ceramic discs or ceramic disc diverters. Temperature is controlled independently via a thermostatic cartridge. Products incorporate approved check valve cartridges, however the complete product has not been fully tested to demonstrate backflow protection. Maximum working pressure: 5.0 bar Maximum operating temperature: 70°C
Range of wall mounted, concealed, thermostatic shower valves, (brass bodies - various trim set finishes), incorporating 2-way ceramic disc diverter valve with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The products incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate that is provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of shower valves with (brass bodies – various finishes) Incorporating either 1 jet or 2 jet setting. Flow is controlled by push button operating members and temperature is controlled via a thermostatic cartridge incorporating a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower handset, hose and overhead shower. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of thermostatic shower valves with a quarter turn ceramic disc headwork and/or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 or 3 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of eccentric lugged or wafer type butterfly valves with stainless teel or blue epoxy coated bodies and stainless steel or epoxy coated ductile iron discs, incorporating EPDM or PTFE seats (see models). Max working pressure: 10.0 Bar, 16.0 Bar or 20.0 Bar (see models). Max operating temperature 80°C or 99°C (see models).
Range of butterfly valves with blue epoxy coated ductile iron bodies, coated ductile iron or stainless-steel discs & EPDM sealing ring. The closing mechanism can be controlled by single lever or a handwheel. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of butterfly valves with ductile iron bodies (blue epoxy coated) and discs. The seats incorporate EPDM seals, and the products are operated via a hand wheel. Maximum working pressure: 16.0 Bar Maximum operating temperature: 60°C
Range of wafer and fully lugged butterfly valves (gear or handwheel operation) with a cast iron body and disc (blue epoxy coated), EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of black nylon coated cast iron equilibrium float operated valves with EPDM seals. Maximum working pressure 10.0 Bar Maximum operating temperature 23.0°C
Range of wall mounted, exposed shower valves (brass bodies various finishes and trim sets), incorporating a quarter turn ceramic disc headwork and either single lever or dome operating member. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of in-line, manually adjustable pressure reducing valves with DZR brass bodies. Some models are available with a pressure gauge. Maximum working pressure: 16bar – outlet pressure range: 1.0 - 6.0 bar. Maximum working temperature: 80°C
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Push fit versions only can also be used with both polybutylene pipe (manufactured to BS7291-2) and PEX pipe (manufactured to BS7291-3) Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with brushed chrome DZR brass bodies. Outlet pressure range: 1.0 - 6.0 bar. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pre-set pressure relief valves (3 bar, 6 bar and 7 bar relief pressures) incorporating brass bodies and an EPDM diaphragm. The valves are fitted with a hand operated rotating easing gear. Maximum working pressure 10.0 bar. Maximum operating temperature 110°C.
Ranges of solenoid valves with plastic bodies, incorporating EPDM ‘O’-rings and diaphragms. The products incorporate a plastic flow regulator and a plastic filter on the inlet. The VAI-FC model can also be supplied with a brass filter. The products incorporate a plastic flow regulator on the outlet, (except for the VAI-FC model). Maximum working pressure 10.0 bar Maximum operating temperature 85°C.
Range of square operated spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Spherical valve with stainless steel body, PTFE seat and stainless steel ball. Valve is operated by lever type handle. Maximum operating pressure 18.0 bar. Maximum operating temperature 60°C.
Range of spherical valves, with DZR brass bodies and brass ball (15mm size) or stainless steel ball (all other sizes). The products can be supplied with various operating members (see model). Jointing is achieved via a crimping tool, the 15-28mm sizes use a ‘M’ profile and the 35-54mm sizes use a ‘V’ profile. The press-fit connection is to be used with copper pipe (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipe (manufactured to EN10305-3). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass or brushed chrome plated bodies, chrome plated brass ball, PTFE seats and lever type operating members. Models with compression joints are for use with BS EN1057 copper pipe. Maximum working pressure 10 - 16 Bar (See model) Maximum operating temperature 85°C
Range of spherical valves with brass bodies (nickel plated), brass ball, PTFE seats and EPDM ‘O’-rings. For use with Polybutylene pipe (manufactured to BS7291 part 2), PEX pipe (manufactured to BS7291 part 3) and copper pipe (manufactured to EN 1057). Maximum working pressure: 6 bar Maximum operating temperature: 95°C
Range of in-line spherical ball valves with brushed chrome brass bodies and PTFE seats. Incorporating lever or T-type operating members. Maximum working pressure: 15mm - 28mm 30 Bar, 35mm - 25 Bar Maximum operating temperature; 99°c
Range of inline or angled screwdriver or lever operated spherical valves with brass or chromium plated brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of crimp fit spherical valves incorporating brushed chrome plated DZR brass bodies and ball, and PTFE seats. The products are supplied with lever operating members. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 99.0°C
Spherical valve incorporating a brass body and chrome plated ball. Maximum working pressure 50.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with bronze bodies and a brass ball, EPDM ‘O’-rings and PTFE seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with ductile iron bodies, wedge and bonnet (blue epoxy powder coated) and EPDM `O` rings and gaskets. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure: 16.0 Bar Maximum operating temperature: 60°C
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle and are supplied with either no operating member or a hand wheel (see models) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Balancing valves with a brushed chrome plated brass body. The compression connection to be used with copper pipe BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of double regulating valves with bronze bodies, DZR brass discs, EPDM `O`-rings and PTFE disc face. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function. The D931, D933 and D934 models incorporate two pressure test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with a bronze body, brass disc face and PTFE seat. The product incorporates two test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'TIANYI SUNS-011'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'Tianyi Suns-0023', version 'TYS-02', dated '2021-05-04'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AMMT-021'. Factory applied, yellow coloured, two-component polyurethane coating. Components A and B are preheated to 65°C and then mixed & sprayed (using a thermal spraying instrument) in a volume ratio of 1:1 according to Application Instructions dated 'APR 2013'. Cure for 7 days@23°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'K-TANK Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 60°C.
'Grilamid TR 60 natural'. Natural (appears amber coloured), injection moulded polyamide material. For use with water up to 85°C.
'TW03'. White coloured (translucent), injection moulded polyethylene thrust washer. For use with water up to 85°C.
'NORYL WM300G-701 (black), NORYL WM300G-960 (grey), NORYL WM300G-801 (beige) & NORYL WM300G-845 (beige)'. Injection moulded PPE+PS materials. For use with water up to 85°C.
'DIC.PPS Z-230-JF BLACK-U'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Noryl PX1630 – 73701'. Black coloured, injection moulded PPE material. For use with water up to 85°C.
'MD001 PPR Fittings'. Green coloured, injection moulded PPR fittings. For use with water up to 65°C.
'RA7050-GN (Green), RA7050-LG (Light grey) & RA7050 (Grey)'. PP-RCT materials for injection moulding and extrusion purposes. For use with water up to 85°C.
'Lubricomp CG002XXN-BKNAT'. Dark grey coloured, injection moulded polystyrene material. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'EP011470P(KAWN)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'OHJI Silicone Rubber Karyu3-type'. Grey coloured, extruded Silicone rubber material. Shore hardness 30. Tested in-radius size 2.75mm. For use with water up to 23°C.
'LOCTITE® 2400™'. Blue coloured, liquid anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘2’, dated November 2024. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'LOCTITE® 6300™’. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.1’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'LOCTITE® 5400™’. Yellow coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.3’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
WC douche set including a trigger spray, flexible hose and wall outlet with stop lever. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor. The temperature for the 107.6917 and 107.6918 models is controlled independently via a single lever operating member. The inlets and the outlet of the 107.6917 and 107.6918 models (main body) incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The 107.5601 and 107.5602 models have an integral soap dispenser (separate to the water pathway). The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assembly (chromium plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor. The inlet of the 107.6826 model incorporates a stainless steel strainer. The 107.5603 model has an integral soap dispenser (separate to the water pathway). The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Floor standing, single hole, single outlet (fixed) combination tap assembly, (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).The spout outlets incorporate plastic aerators. The shower outlet incorporates an approved single check valve cartridge, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (black or chrome plated brass). The flow is controlled via solenoid valve which is actuated by an infra-red sensor and the temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies models AI-903215 & Al-903222 are chrome plated. Maximum working pressure 16 Bar Maximum operating temperature 60°C
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Range of single hole, single outlet fixed (over the rim swivel nozzle) bidet combination tap assemblies stainless steel or brass bodies with various finishes, incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a swivel nozzle with a plastic aerator. The products are also supplied with a lever type pop-up waste. Maximum working pressure 3.0 Bar Maximum operating temperature 60.0°C
Shower flow regulator with a plastic body and EPDM O-rings incorporating a (chrome plated brass) housing Maximum operating temperature 85°C.
Single-hole, single outlet (swivel) combination tap assemblies (brass body – various finishes) incorporating a ceramic cartridge (F73V) or quarter turn ceramic disc (F74V) headwork with a single lever operating member. The products have a pull-out spray outlet which incorporates a plastic aerator and trigger mechanism that stops the flow (model (F74V) or changes the water pattern from straight flow to spray (F73V). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Models 4E1022 & 4E1021 are supplied with a click type waste – not verified by test. Maximum working pressure; 5 Bar Maximum operating temperature; 60°c
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or aerator. These products are also supplied with a click type waste – not verified by test. Maximum working pressure; 5 Bar Maximum operating temperature; 60°c
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar or 10.0 Bar
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193938 X XXX | VARIOUS | ½” BSP | 5.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 194828 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 181028 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet combination tap assemblies, (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with DZR brass adaptors for installation on each inlet. The adaptor incorporates a stainless-steel strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Supplied with a lever type pop up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with either stainless steel (models 49xxS604WF & 49xxP704WF only) or brass (all other models) bodies (various finishes). The products incorporate a ceramic cartridge headwork with either single lever, cylindrical or no supplied operating members (see models). The spout outlets incorporate a plastic aerator and model 58xxL904F is supplied with a lever operated pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 80°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlet hose incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single outlet, single outlet (swivel) combination tap assembly (chromium plated brass body), incorporating quarter turn ceramic disc headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 6.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with dome type operating members (model 71 222 xx0 incorporates cross top operating members). The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies with a brass or stainless steel bodes (various finishes). (CAS, COU, ALP, FON & CHI series) incorporating ceramic cartridge headworks with single lever operating members. (CUR & EIB series) incorporate quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 to 10.0 Bar. Maximum operating temperature 60.0°C.
Deck mounted two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure; 6 Bar Maximum operating temperature; 60°c
Range of wall mounted, concealed, two-hole single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with single lever operating members. The concealed body is either brass (6317-** model) or nickel plasted brass (all other models). The spout and trim set have brass bodies with various finishes, see model. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperatures 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with dome operating members. The spout outlets incorporate plastic aerators or flow straighteners. The product is supplied with metal back nuts. Maximum working pressure – 10.0 Bar Maximum operating temperature - 70 °C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 70 °C
Range of wall mounted, concealed, two-hole single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with single lever operating members. The concealed body is either brass (UBR0257) or nickel plated brass (all other models). The spout and trim set have brass bodies with various finishes, see model. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperatures 65°C.
Range of wall mounted, two hole, single outlet fixed combination tap assemblies, (brass bodies - various finishes). (Series 9097) incorporates ceramic disc diverter valve controlling the flow. Temperature is controlled independently via a thermostatic cartridge Incorporating a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. All other models incorporate ceramic cartridge headworks with single lever operating member and ceramic disc diverter valves diverting flow between spout outlet and shower outlets. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted spouts (plastic body). The outlet incorporates a plastic flow straightener. This product has not been tested or approved for claims of sterile properties made by the approval holder. Maximum operating temperature 60.0°C.
Range of cylindrical expansion vessels with epoxy coated or uncoated steel bodies and Butyl membranes. Maximum working pressure 10.0 Bar Maximum operating temperature 99.0°C.
Range of in-line water filters with plastic bodies. Maximum working pressure 8.0 bar. Cold water use only.
Range of carbon filter cartridges. Cold water use only.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flowtech range of fusion welded, PP-RCT fittings for use with Flowtech PP-RCTGF pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of plastic, push-fit fittings (wall plate elbow, equal elbow, end stop, pipe insert, equal straight and equal tee) for use with MDPE pipe (manufactured to BS EN 12201), for above and below ground use. Copper adaptors are for use with PB pipe (manufactured to BS7291-2), PEX pipe (manufactured to BS7291-3) or Copper pipes (manufactured to BS EN 1057) and are for above ground use only. Maximum working pressure 16.0 bar. Cold water use only.
Range of copper end feed fittings for use with copper tube to EN 1057. For above and below ground use. Maximum working pressure: 6mm-54mm 16.0bar, 64mm-108mm 10.0bar. Maximum operating temperature 85°C
Electric instantaneous water heater with a plastic casing. Flow is controlled via a solenoid valve operated by an infrared sensor. Temperature is controlled by a dial on the front of the unit. The product incorporates a swivel arm outlet from the base. Maximum working pressure 3.0 bar. Maximum operating temperature 48˚C. Cold supply only.
Range of water meters with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with blue epoxy coated ductile iron bodies, plastic measurement chambers and vanes and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with brass bodies and plastic turbines. The inlet incorporates a plastic filter. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with either cast iron (blue epoxy coated) or stainless-steel bodies, transducers and EPDM rubber O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 50.0°C.
Range of wall brackets (brass bodies – various finishes). Open outlet use only Maximum working temperature 85°C
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of accumulators. The brass vessel connector of the ACC-060-TNK, ACC-120-TNK and ACC-180-TNK models incorporates a plastic flow regulator. Maximum working pressure 8.6 bar. Cold water use only.
Range of pumps with plastic bodies. Maximum working pressures: 41.007.400 model: 0.28 bar, 41.008.400 model: 0.38 bar. Maximum operating temperature 96°C
Range of single, twin & triple cold water booster sets. The products incorporate one or more pumps, expansion vessels, isolation valves and non-return valves (not suitable for backflow protection). The twin and triple models include a suction and discharge manifold. Maximum working pressures - see model. Cold water use only.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless steel filter and a plastic flow regulator. Maximum working temperature 60°C.
Shower handset with a stainless-steel body (various finishes - see model) and silicone nozzles. The inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 65°C.
Range of shower arms, (stainless steel bodies – various finishes). Open outlet use only. Maximum operating temperature - 85°C
Range of overhead shower and shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VR1000 | Chrome | 15mm | 5 bar | 60 °C | Bristan | Body | No | Not applicable | Metal Backnuts | Not Applicable | Fixed Head, |
Range of shower kits comprising of a shower hose, handset and riser rail assemblies. Models (AOSRCPUK & AOSRBK) are supplied with a round or square wall outlet. Maximum operating temperature 60°C. Open outlet use only.
Range of shower sets incorporating either a wall elbow or wall elbow with hand shower, (chromium plated brass). The shower holder incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only Maximum operating temperature 60.0°C
Range of In-line Y patterned strainer with cast iron bodies (blue epoxy coated) and stainless-steel screens. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Wall mounted bib tap with a nickel-plated brass body, chrome plated brass ball, NBR ‘O’-rings and gasket, and PTFE seats. The product incorporates a hose union outlet with an integral plastic flow straightener. Maximum working pressure 20.0 bar. Maximum operating pressure 85°C.
Range of pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with a metal back nut. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Pillar tap (chromium plated brass) with quarter turn ceramic disc headworks and a single lever operating member. The spout outlet incorporates a plastic flow straightener, and the product is supplied with a metal back nut. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MEFC-PAK | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Fixed Head | No | Self closing | Not Applicable | Not Applicable |
Range of PVC plastic shower hoses with black and silver corrugated outer, with EPDM washers. Maximum operating temperature 60°C.
Multi-layer PVC shower hoses with silver coating, brass end connections, EPDM gasket and NBR ‘O’-ring. Open outlet use only. Maximum operating temperature 65°C
Range of PVC outer layer shower hoses with a PVC internal layer and EPDM washers. Open outlet use only. Maximum operating temperature:60C
Range of wall mounted, or concealed manually operated blending valves, (brass bodies – various finishes), incorporating a ceramic cartridge headwork controlling both the flow and temperature with a single lever operating member. Maximum working pressure 5 bar. Maximum operating temperature 85°C.
Range of wall mounted, thermostatic bar shower mixers (brass bodies – various finishes), incorporating a quarter turn ceramic disc headwork that controls the flow with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with dome type operating member that incorporates a manual override button. Products incorporate a half turn ceramic disc headwork that diverts the flow to an overhead shower or shower handset. Both inlets incorporate an approved check valve cartridge and stainless steel strainers however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5 bar. Maximum operating temperature 60 C.
Range of wall mounted bar type thermostatic shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc headwork which controls the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic bar shower mixers ((brass bodies - various finishes), incorporating a quarter turn ceramic disc headwork controlling the flow with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with single lever type operating members. Models come with either 2,3 or 4 push type headworks for different functions. The inlet incorporates approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Products are supplied with a shower handset, shower hose. The products need to be installed in combination with a specific basic set. 12 571 xx0= 18310180 Basic set for thermostatic module Select for 2 functions (WRAS 2207061) 12 572 xx0= 18311180 Basic set for thermostatic module Select for 3 functions (WRAS 2207061) 12 573 xx0= 18312180 Basic set for thermostatic module Select for 4 functions (WRAS 2207061) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Wall mounted thermostatic shower panel ((brass bodies - various finishes), incorporating a quarter turn ceramic disc headwork controlling the flow with single lever type operating members. The temperature is controlled independently via a thermostatic cartridge with single lever type operating members. Model has 3 push type headworks for different functions. The inlet incorporates approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). Products are supplied with a shower handset, shower hose. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of wall mounted bar type thermostatic shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc headwork which controls the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of wall mounted thermostatic, bar type shower valves. Model (704309) incorporate quarter turn ceramic disc headworks and model (704308) incorporates a non-rising spindle headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge that incorporates a manual override button. Both using either dome, cubed or single lever type operating members. The inlets incorporate stainless steel strainer washers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of wall mounted bar type thermostatic shower valves (brass bodies – various finishes) incorporating ceramic disc headwork which controls the flow to 2 outlets with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member which incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an optional flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of wall mounted, concealed, thermostatic shower valves (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork which controls the flow using various operating members. Temperature is controlled independently via a thermostatic cartridge with a manual override button also using various operating members. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C
Bar type thermostatic blending valve with a chromium plated brass body, a quarter turn ceramic disc headwork with single lever type operating member controlling the flow. Temperature is controlled by a thermostatic mixing valve with a single lever type operating member incorporating with a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of thermostatic shower valves with a quarter turn ceramic disc headwork and/or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 or 3 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, thermostatic shower valves (brass bodies – various finishes) incorporating a ceramic disc diverter with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with dome type operating members incorporating a manual override button. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C
Range of wall mounted concealed thermostatic shower valves (brass bodies – various finishes) incorporating a manual diverter to shower outlets and quarter turn ceramic disc headwork controlling the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating member. Both inlets incorporate approved single check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C
Range of gear operated butterfly valves with blue epoxy coated ductile iron bodies. Maximum working pressure 10.0 & 16.0 bar. Maximum operating temperature 60°C.
Range of handwheel operated butterfly valves, incorporating blue epoxy coated ductile iron bodies and discs, with EPDM seats. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of butterfly valves with blue epoxy coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of lugged or wafer butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of 2-way or 3-way ceramic disc diverters with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of control valves with plastic bodies, supplied with bypass valves. Maximum working pressure 8.6 bar. Maximum operating temperature 39°C.
Range of in-line pressure reducing valves with either chromium plated DZR brass bodies, with manually adjustable outlet pressure ranges between 2.8bar to 3.2bar. Compression connections to be used with copper pipe EN1057 only. Maximum working inlet pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar or 1.0 and 12.0 bar (see model). Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 6.0bar. Maximum working pressure: 25.0 Maximum operating temperature 80°C.
Range of in-line, manually adjustable pressure reducing valves with DZR brass bodies. Some models are available with a pressure gauge. Maximum working pressure: 16bar – outlet pressure range: 1.0 - 6.0 bar. Maximum working temperature: 80°C
Pressure relief valve set at 6.0 Bar with a DZR brass body. Max operating temperature 100 ºC
Range of pressfit connection spherical valves incorporating DZR brass bodies, PTFE seat and packing, NBR ‘O’-rings and various operating members: lever, lever lockable, T-handle and butterfly. For use with copper pipe (manufactured to BS EN 1057), stainless steel pipe (manufactured to BS EN 10312) and carbon steel pipe (ISO 4200 Groupe 1 Series 3). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of lever or butterfly operated spherical valves with DZR brass bodies. Incorporating DZR brass ball . For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of angled spherical valves, (brass bodies – various finishes), incorporating a brass ball and a dome type operating member. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of in-line spherical ball valves with brushed chrome brass bodies and PTFE seats. Incorporating lever or T-type operating members. Maximum working pressure: 15mm - 28mm 30 Bar, 35mm - 25 Bar Maximum operating temperature; 99°c
Range of ball valves with DZR brass bodies and a stainless-steel ball. The valves are available with lock shield, butterfly or single lever operating members. The threaded end connections have hexagonal spanner flats. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of crimp fit spherical valves incorporating brushed chrome plated DZR brass bodies and ball, and PTFE seats. The products are supplied with lever operating members. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 99.0°C
Range of lever operated spherical valves with DZR brass bodies. Incorporating a chrome plated DZR brass ball and PTFE seat. Maximum operating pressure 25.0 bar (models 00/0095) or 16.0 bar (models 00/2094). Maximum operating temperature 100°C.
Range of lever operated spherical valves with nickel plated brass bodies, chromium plated brass ball, PTFE seats and a drain valve. Maximum working pressure 25.0 Bar Maximum operating temperature 100.0°C
Range of spherical valves, with brass bodies (either nickel plated or chromium plated) and a chromium plated brass ball. The products can be supplied with various operating members (see model). The products are to be used with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves having brass, DZR brass or stainless-steel bodies and lever type operating members. For use with stainless steel pipe (EN10312) or copper pipe (EN1057). Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C.
Range of ball valves with DZR brass bodies and a stainless-steel ball. The valves are available with lock shield, butterfly or single lever operating members. The threaded end connections have hexagonal spanner flats. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models RSF-002A(Metal Seat) & RSF-002B(Metal Seat) incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of non-rising spindle gate valves with bronze, brass or DZR brass (V2143R) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (V2143R) 25.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Screw down stop valves with brass bodies and dome type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of commercial dish washing machines with flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of Electromagnetic water conditioners. Maximum working pressure 16.0 bar. Cold water use only.
Water filter and scale inhibitor comprising of a plastic filter head and plastic filter cartridge with an activated carbon block and sodium polyphosphate. The push-fit connections are for use with LDPE pipe (manufactured to DIN 8072). Maximum working pressure 5.52 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
'IUPITAL F30-EW'. Natural, (appears white coloured - opaque), injection moulded POM material. For use with water up to 85°C.
'ANUBIT HB-1000'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's TDS 'AE-TDS-023-2021', dated '02.08.2024'. Please note that use of a thinner isn't covered by the scope of this approval. Cure for 40 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac High Build Bituminous Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's work instruction document 'GPC/WI/10' issue no. '01', dated 03/01/2018. Cure for 72 hours@30°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HT 204'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'P.HSR 42.5-010Y'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'JXT/JS02-10', edition '1/0', dated '2021-11-30'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue and Jotapipe AC - 1003 Green'. Factory applied, blue or green coloured fusion bonded epoxy coatings (manufactured in Dubai, U.A.E). Apply as per manufacturer's Technical Data Sheet dated 26th September 2019. Cure for 2 minutes@245°C. The blue coating is for use with water up to 85°C. The green coating is for use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-XP2501'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'XP2503-010', dated '2025-03-25'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'P.HSR 42.5-RVK2025'. Factory applied, grey coloured, Sulphate resistant Portland cement. Mix cement, sand and water in a 1:1.5:0.5 mass ratio and apply as per manufacturer's usage instructions 'RVK2503/25', dated 'March 25, 2025'. Cure for 240 minutes@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Guom-07'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a weight ratio of 1:1.5:0.6 and apply as per manufacturer's User Instructions 'GUOM-24', 'Vision: B', dated '2024-11-5'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MAVM554'. Factory applied, blue coloured, epoxy powder coating. Apply as per manufacturer's data sheet 'FR.07.03.18', dated 09.19. Cure for 10 minutes at 160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC - 1003 Blue & Green. Factory applied, green or blue coloured epoxy coatings (manufactured in Dammam, Saudi Arabia). Apply as per manufacturer's MTI '001 - 2024 - SA – EN'. Cure for 4 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electroline ES 424'. Factory applied, white coloured, two-component epoxy coating. Mix Part A and Part B in a volume ratio of 2:1 and apply as per manufacturer's TDS 'ECL/ TDS / ES424', version '0', dated '05.01.2024'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat Epoxy Blue Patch Up Paint (PFC/1017)'. Factory applied, blue coloured, two-component epoxy coating. Mix in a 3:2 volume ratio and apply as per manufacturer's IFU 'DOC/PFC/PU/101', dated '01.04.2024'. Cure for 8 hours@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EM6/35/7541/1'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monoflex W'. Grey coloured, extruded TPO 'tape'. Shore hardness 91. Tested in-radius size 0.45mm. For use with water up to 70°C.
'LEAKBLOK® P100'. Green coloured fibre/NBR gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'SPS GRP Pipe'. Multi-layered, beige coloured GRP pipe, made by Continuous Filament Winding. For use with water up to 60°C.
'SANIBIW WB60 & SANIBIW WB80'. Off-white coloured, transparent, extruded silicone rubber hoses. Shore hardness 60 & 80. Tested in-radius size between 0.5mm & 1.5mm. For use with water up to 85°C.
'EPDM W8528'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SL7065/SL7015'. Extruded, triple layered hose comprising of a translucent, silicone inner layer, white coloured polyester middle layer and translucent, silicone outer layer. Shore hardness 70. Tested in-radius size of complete hose is 1.8mm. For use with water up to 65°C.
'LH-02 EPDM Hose'. Black coloured, extruded EPDM rubber hose. Shore hardness 80. tested in-radius size 0.8mm. For use with water up to 85°C.
'Bonline LY S 5000'. Colourless, translucent silicone oil. Apply as per manufacturer's instructions. For use with water up to 85°C.
'7740 WPG'. White coloured, silicone based lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'A7G10E'. Black coloured, injection moulded PPA material. For use with water up to 85°C.
'Grilon AG-30 FWA Black'. Black coloured, injection moulded, PA66-GF30 material. For use with water up to 85°C.
'Hydropriv PE80 Pipe'. Black coloured (with blue external stripes) and blue coloured, extruded PE80 pipe. For use with water up to 23°C.
'T-MECH PE-Xb Pipe’. White coloured (opaque), extruded PEX pipe. For use with water up to 85°C.
'PE002'. Blue coloured, HDPE fitting manufactured by mould pressing. For use with water up to 60°C.
'PIPELIFE - ARILI HDPE PE100 Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 23°C.
‘SABIC P6006AD’. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'Tecotek OP20 GR30 BG018 01 0A QF'. Beige coloured, injection moulded PPO/HIPS material. For use with water up to 85°C.
'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'Fluteck™P1000 & Fluteck™P1500'. White coloured, extruded, disc shaped PTFE components. For use with water up to 85°C.
'Dalcon 001'. White coloured, compression moulded or extruded PTFE material. For use with water up to 85°C.
'RVK EPDM-LJHY'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AA7BCZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NE7130-XT'. White coloured (translucent), injection moulded Silicone rubber. Shore hardness 60. Tested in-radius size 2.0mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Cyberbond® SH27'. Yellow coloured (translucent) anaerobic adhesive. Apply as per manufacturer's TDS 'V01.005.en-gb.001'. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'WS27TF Pipeseal'. Yellow coloured anaerobic adhesive. Apply as per manufacturer's datasheet issue '1.0'. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Vyncolit BXE650W'. Black coloured, injection moulded phenolic material. For use with water up to 85°C.
'JFD-PVCR01'. Beige coloured, extruded PVC pipe liner. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of spring loaded resilient trim check valve cartridges with plastic bodies. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Spring loaded resilient trim check valve cartridge with plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of tundishes with plastic bodies. The tundish complies with the requirements of an air gap to drain. Maximum operating temperature 85°C.
Range of assisted bathing units. The flow is controlled via an electronic thermostatic mixing valve which can feed either a bath spout outlet or shower handset. The discharge from both the bath spout and shower handset are via a type AUK 3 airgap, verified by measurement, suitable for fluid category 5 backflow protection. These bathing units have adjustable height and tilt functions. Maximum working pressure 6.0 Bar Maximum operating temperature 45.0°C
Range of either half turn, quarter turn ceramic disc or non-rising spindle headworks with brass bodies and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum working pressure 20.0 Bar Maximum operating temperature 90.0°C
Range of ceramic cartridge headworks with plastic bodies, incorporating EPDM seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar (D40P-17 & D40G-17) or 20.0 Bar (D25G-6) Maximum operating temperature 85.0°C
Range of ceramic cartridge headworks with plastic bodies and silicone ‘O’-rings and gaskets for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks with brass bodies. For insertion into any specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge and 2-way ceramic disc diverter headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes), incorporating non-rising spindle headworks and single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Supplied with a lever type pop up waste – not tested. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Models 6500H/W & 6504/W are supplied with a click type waste – not verified by test. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 235038 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | |
| 223238 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole single outlet (fixed) combination tap assemblies (chrome plated), with a ceramic cartridge headwork and flow straighter in the spout outlet. Supplied with a click type waste (verified by test). Maximum working pressure - 5.0 bar. Maximum operating temperature - 60 °C.
Single hole single outlet (fixed) combination tap assemblies (chrome plated), with a ceramic cartridge headwork and flow straighter in the spout outlet. Supplied with a click type waste (verified by test). Maximum working pressure - 5.0 bar. Maximum operating temperature - 60 °C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass) bodies, incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Product supplied with a surface mounting kit comprising of Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” BSP captive nut end connections with 15x15mm compression isolation valves that incorporate single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Floor standing, single hole, single outlet (swivel) combination tap assembly with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A deck mounted two hole, single outlet (fixed) combination tap assembly, with a brass body (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with metal back nuts and plastic aerators. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass body), incorporating ceramic cartridge headwork with single lever operating member. The headwork and the spout are connected by a PEX lined flexible hose. The spout outlets incorporate a plastic aerator, and the products are supplied with metal backnuts. Models supplied with pop-up waste – not tested. Maximum working pressure 10 Bar. Maximum operating temperature 70°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223206 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 85 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle option – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall and deck mounted thermostatic combination tap assemblies (brass bodies – various finishes), incorporating a two way ceramic disc diverter headwork controlling the flow from spout outlet to shower outlet using dome type operating members. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with dome type operating members. The spout outlet incorporates a plastic aerator. The inlets incorporate an approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 223205 X XXX | VARIOUS | 3/4” BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : without suffix indicates no handle / different handle – A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of two hole, deck mounted, single outlet (fixed), combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to the shower outlet. The outlet incorporates an elbow to connect a shower hose to the headset. The spout outlet incorporates an aerator, and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet, fixed combination tap assembly (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet. The spout outlet incorporates a plastic aerator. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar. Maximum operating temperature 60 °C.
Range of two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two hole, double outlet (swivel) combination tap assemblies (chrome plated brass). (T-695 series) Incorporates quarter turn ceramic disc headworks with single lever operating members. (T-695M series) incorporates non-rising spindle headworks and dome or cross top type operating members (T-695M). The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Three-hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator and is connected to the headworks via stainless steel braided PEX lined flexible hose assemblies. The product is supplied with a flow regulator and lever type pop up waste, not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted three-hole, single outlet (fixed) combination tap assemblies (chromium brass bodies). Incorporating quarter turn ceramic disc headworks and lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Three-hole, deck mounted single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The headworks are connected to the spout with stainless steel braided PEX lined flexible hose assemblies. The spout outlet incorporates a plastic aerator. Supplied with a lever type pop up waste, not verified by tested. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of three-hole, wall mounted single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headwork with either single lever, dome, wheel or cross top operating members. The headworks are connected to the spout with stainless steel braided braided PEX lined flexible hose assemblies. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted spout outlet (Chrome finish). The spout outlet incorporates a plastic aerator. Open outlet use only. Maximum operating temperature 60.0°C
Floor standing spout outlet (chromium plated brass) incorporating a plastic aerator and a concealed brass floor mounting. Maximum operating temperature 60°C.
Range of chemical dosing equipment which incorporate self-closing valves within a plastic body with EPDM o-rings. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Only suitable for use with chemicals no greater than a FC3, additional backflow protection is required for chemicals greater than FC3. Maximum working pressure 9.0 bar. Maximum operating temperature 70ºC.
‘LFLF10xx’ range of stainless steel press-fit fittings incorporating EPDM ‘O’-rings for use with ‘LFLP1001’ stainless-steel pipe. Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘CFxx and TFxx’ range of brass compression fittings for use with copper pipes and Irish copper pipe (both manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
‘Universal Transition Coupling (UTC)’ range of plastic compression fittings for use with the following pipe types and sizes: Stainless steel (manufactured to ASTM A554/ BS EN 10312): ¾”, 1” & 1¼”. Galvanised (EN 10255): ¾”, 1”, 1¼”, 1½” & 2”. Copper (BS EN 1057): 15mm, 22mm & 28mm. PVC (BS EN 1452): 20mm & 2”. ABS (BS 5391-1): 20mm, 25mm & 32mm. PE80 & PE100 pipe (to BS EN 12201): 20mm, 25mm, 32mm, 50mm & 63mm. For use above and below ground. Maximum working pressure 12.5 bar. Cold water use only.
Range of Copper and Brass push fit fittings. Brass fittings are for use with PB pipe (manufactured to BS7291-2) & Copper pipe (manufactured to BS EN 1057) only. Copper fittings are for use with PB pipe (manufactured to BS7291-2), PE-X pipe (manufactured to BS7291-3) & Copper pipe (manufactured to BS EN 1057). Maximum working pressures and operating temperatures when used with: PB & PEX pipe – 3.0 bar and 92°C, 20.0 bar cold water. Copper pipe – 20.0 bar and 100°C.
Flomasta Range of plastic, push-fit fittings (wall plate elbow, equal elbow, end stop, pipe insert, equal straight and equal tee) for use with MDPE pipe (manufactured to BS EN 12201), for above and below ground use. Copper adaptors are for use with PB pipe (manufactured to BS7291-2), PEX pipe (manufactured to BS7291-3) or Copper pipes (manufactured to BS EN 1057) and are for above ground use only. Maximum working pressure 16.0 bar. Cold water use only.
Range of float operated electrical switches with plastic bodies. Open outlet and cold water use only.
Range of WC dual flush drop valves with an ABS body and silicone seal. The valves are operated via a push button or lever assembly for either full or reduced flush and incorporate an internal adjustable height overflow. Cold water use only.
‘Altair V4’ range of in-line and manifold volumetric water meters with brass or plastic bodies (see models), the products can be provided with a plastic strainer. Maximum working pressure 16.0 bar. Cold water use only.
Range of ultrasonic water meters with plastic bodies and plastic strainers at the inlets. Specific models (see models) incorporate an optional non return valve (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 90°C.
WSTsb range of bulk water meters with blue polyester coated cast iron bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of electromagnetic water meters with stainless steel bodies and a polyamide coating. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with brass bodies, plastic turbines and plastic strainers on inlets. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Top entry compression cylinder flange with DZR brass body and copper anti-aeration dip tube. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 4.0 bar. Maximum operating temperature 60°C.
Leak detection system, comprising of a flow sensor with a stainless-steel body incorporating a motorised spherical valve, with a stainless-steel ball. Please note that claims of leak detection have not been verified by WRAS. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Brass flow meter and smart box water monitoring system. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of installation kits comprising of a water block, double check valve assembly (suitable for backflow protection against fluid category 3) and a pressure reducing valve (outlet pressure range 3.0 to 3.5 bar). Model 95428 incorporates a water filter. Maximum working pressure: 16 Bar Maximum operating temperature: 23°C
Range of cold water booster sets comprising of multistage stainless steel pumps and manifolds with a common control panel and motor mounted inverters. The products incorporate spherical valves between the inlet and outlet manifolds and the pumps. The outlet manifold incorporates an anti-head loss valve and a flow through valve with an expansion vessel factory pre-set at 10.0 bar. Maximum working pressure 10.0 bar. Cold water use only.
Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The Movitec VME models can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Comeo C models 10.0 bar, Movitec VM models with an oval flange or VME models with integral check valve 16.0 bar, All other Movitec VM models 25.0 bar Maximum operating temperatures: Comeo C and Movitec VME models with integral check valve 60°C, all other model variants 100°C.
Permanent magnet multi-stage centrifugal pump with a plastic body. The product is supplied with brass adaptors and a copper olive to convert to compression. The compression connections are for use with Irish copper pipe (manufactured to EN1057) (27.4mm size) and copper pipe (manufactured to EN1057) (28mm size). Maximum working pressure 8.0 bar. Maximum operating temperature 90°C.
Range of overhead shower outlets brass and stainless-steel bodies in various finishes, incorporating stainless steel filter washers and flow regulators. Open outlet use only. Maximum operating temperature 85⁰C.
Range of wall and ceiling mounted overhead shower outlets, (plastic bodies – various finishes). Both models incorporate a built-in pressure regulator. Maximum operating temperature 85°C. Open outlet use only
Range of deck mounted pull out kits (various finishes) comprising of a shower handset, shower hose and a stainless steel braided silicone lined connecting hose. The shower handsets incorporate single check valve cartridges, however, the complete product has not been fully tested to demonstrate backflow protection. Maximum operating temperature: 60°C. Open outlet use only.
Page 11 of 12
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
