Range of single hole, single outlet, swivel, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Model BLS4ZZX is supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever or cross top operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C.
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic flow straighteners. The products are supplied with a 15x15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) which also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating non-rising spindle headworks with dome type or cross top operating members. Both models are supplied with a plastic flow straightener. Capable of achieving AUK3 Tap Gap Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, double outlet (swivel) combination tap assembly (chrome plated brass body). Incorporating a ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 70.0°C
Range of deck mounted, two hole, double outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks (DLV305B, DLT305B) or non-rising spindle headworks (CR305 BRIDGE, CR305/501 BRIDGE) and single lever or cross top operating members. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two hole, double outlet (swivel) combination tap assembly incorporating quarter turn ceramic disc headworks with single lever type operating members. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assemblies (brass body, chrome finish), incorporating quarter turn ceramic disc headworks and single lever operating members. The products are supplied with metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc headwork with dome type operating member. Temperature is controlled independently via thermostatic cartridge with single lever operating member. The inlets incorporate a stainless steel strainers and an approved check valve cartridge, however the complete product has not been fully tested to demonstrate It provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and a lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8204 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8184 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| SH-T8035 | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-QT8066B | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F3068-** | Various | BSP 3/4" (M) | 10 bar | 60 °C | LANBIAO | Rear of body | No | Ceramic disk diverter | Metal Backnuts | Aerator | Flow Regulator Fitted, |
1)No Suffix-Chrome 2)-**Represents the following different surface treatments: 1.H-Black 2.DYB - Matte white 3.BZ - Perl white painted 4.HGTS - Red bronze 5.HTL = Yellow bronze brushed 6.Q = Bronze 7.QTSL = Bronze brushed bright 8.QTS = Bronze brushed matte 9.STS = Acid copper brushed 10.SDMGJ = Water plated rose gold 11.N = Nickel brushed bright light 12.NP = Nickel brushed 13.TJ = Titanium gold 14.TJLS = Titanium gold brushed 15.G = Gold 16.GJS = Gold brushed 17.GJSY = Zirconium gold wire drawing matte 18.PGJFY = Zirconium gold wire drawing matte bright light 19.PLSJ = Brushed gold 20.LSJY = Brushed gold matte 21.MGJ = Rose gold 22.MGJL = Rose gold brushed 23.DMGJ = Light rose gold brushed 24.HTS = Red bronze brushed 25.QHP = Grey 26.LSQH = Grey brushed 27.LHMGJ = Brushed yellow rose gold
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8060A | Chrome | G3/4,male | 10 bar | 60 °C | SHANHU | body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT010R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| SL-KT008R | Various | ½" BSP (M) | 10 bar | 60 °C | Taizhou Shenglang Sanitary Ware Co., Ltd logo | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener |
Various finish： (1) Without suffix to current model number: Chrome plated (2) With suffix B: Black (3) With suffix BB: Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC BDSM C MT | Chrome | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet | |
| RP3 VAC BDSM C MT | Chrome 3 | 1/2" BSP (M) | 8.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | Metal Backnuts | Open Outlet |
Range of three-hole, single outlet, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up or lever type waste – not verified by test. Maximum working pressure. 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B005* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of three-hole, single outlet (fixed) wall mounted combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with lever or cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| B004* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| B009* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | Rosette | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
*denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of combined bath waste and overflow assemblies in various finishes.(see models for finishes) Maximum operating temperature: 60ºC
Range of free-standing sanitary macerating disposal units. The units are fed via a flexible hose assembly. Flow is controlled by a solenoid valve and discharges via a type `AB` air gap (verified by test, suitable of fluid category 5 backflow protection). Maximum working pressure 6.0 Bar Maximum operating temperature 40.0°C
Shock arrestor with stainless steel body and EPDM diaphragm. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
F1C compression & F5 press fittings for use with B1 multilayer PEX/AL/PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of DZR brass compression fittings for use with Q-Therm PEX-b Pipes (SDR 7.4) Maximum working pressure:20 bar, cold water use only
Range of compression fittings with brass, nickel plated brass bodies for use with copper pipe (manufactured to EN 1057). For above ground use only. Max working pressure 16.0 bar. Max operating temperature 85°C.
‘HLBRxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The HLBRTC‐1 tank connector, HLBRSS‐1 and HLBRBS‐1 tap connectors all incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘3600xx’ range of brass compression fittings for use with copper pipe (manufactured to EN 1057). The 360014 tank connector, 360013 and 360017 tap connectors all incorporate an EPDM washer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘CFxx’ range of brass or DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
Range of compression fittings with polypropylene bodies for use with PE100 pipe (manufactured to EN 12201). Some of the female adaptors (55920-9-L, 55920-10-L, 55920-11-L & 55920-11-M), female threaded elbows (56935-10-L, 56935-11-L & 56935-11-M) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 16.0 bar. For above and below ground, cold water use.
‘F17’ range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
'PlumbRight' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure 12.5 bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Dual flush, WC outlet valves for either full or reduced flush. Incorporates an internal overflow. Cold water use only.
Stainless steel plate heat exchangers with copper brazing.
Range of pre-assembled hydraulic blocks incorporating plate heat exchangers, pressure relief valves set at 3.0 bar, circulation pumps and flow regulators. Maximum working pressure: Primary 2.5bar & secondary 10 bar. Maximum operating temperature 80°C (CH) & 60°C (DHW).
Range of floor-standing gas combination boilers, supplied with isolation valves, expansion vessel and a pressure relief valve set at 3.0 bar. Maximum working pressure: Primary circuit 2.5 bar, secondary 10 bar. Maximum operating temperature: Primary 82°C / secondary circuit 60°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
An in-line ultra-sonic water meter with brass (WM15) or plastic (SM15) bodies. Maximum working pressure: 16 Bar. Maximum operating temperature: 50°C (WM15) or 70°C (SM15).
Range of water meters with plastic bodies and EPDM ‘O’-rings. The inlets incorporate a plastic strainer. Maximum working pressure 10.0 Bar Maximum operating temperature 50.0°C
Range of water meters with plastic bodies and plastic turbines. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Wall outlet socket with brass body. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Compact wall outlet elbow with brass body (various finishes). Maximum operating temperature 85.0°C Open outlet use only
Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.
Range of EPDM expansion joints with flanged end conenctors. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.
Range of overhead shower heads and arms incorporating a brass or ABS plastic body. The inlet of models KSAB4K and HEAH06BK incorporates a stainless-steel strainer and plastic flow regulator. Model EKIT01/A is a shower kit consisting of a shower hose, handset and riser rail and model AIR1HSCPWHUK shower handset only. Open outlet use only. Maximum operating temperature 60°C.
Range of shower handsets and headsets with chromium plated plastic bodies incorporating check valves fitted at the inlets however, the complete products have not been fully tested to demonstrate they provide backflow prevention. Maximum working pressure: Open outlet. Maximum operating temperature: 60.0°C.
Range of wall mounted angled overhead showers, consisting of stainless-steel bodies (various finishes) and silicone nozzles. The inlets are fitted with plastic flow limiters. Maximum operating temperature 65⁰C. Open outlet use only.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of flanged `Y` patterned in-line strainers with blue, black or red epoxy coated ductile iron bodies, stainless steel mesh. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of draining taps, straight or elbowed with brass bodies incorporating a rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 95.0°C
Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps will be supplied with an optional Flow Regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 936L | Chrome | G3/4, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 932L | Chrome | G1/2, male | 10 bar | 60 °C | WRAS, XINYA | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.
FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C
Range of EVOX stainless steel or grey nylon braided polyethylene lined flexible hose assemblies incorporating EPDM ‘O’-rings with various end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘KM1001 series’ of stainless steel braided EPDM lined flexible hose assemblies. Compression end connections are for use with copper pipes (manufactured to EN 1057). Compression end connections are also available with brass bodied (nickel plated) isolation valves incorporating a chrome plated brass ball. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.
Range of wall mounted, thermostatic shower valves (brass body – Chrome finish), incorporating a single sequential headwork controlling both temperature and flow using a single lever operating member. The inlets incorporate stainless-steel strainers, plastic flow regulators and approved check valve cartridges (verified by test - suitable for backflow protection against fluid category 2) Product is not supplied with shower hose, handset, overhead shower or riser rail assembly. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves with chrome plated brass bodies and ceramic disc headwork with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge also with a dome type operating member. Inlets incorporate single check valve cartridges however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves with brass bodies (chromium plated) incorporating a ceramic disc controlling the flow to the shower (for some models it diverts the flow to a hand shower or overhead shower) using a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Inlets incorporate stainless steel strainers and an approved single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 50°C
Range of butterfly valves incorporating blue or green epoxy coated ductile iron bodies, discs and EPDM seals. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Combined pre-set temperature and pressure relief valves (set at 7.0 bar) incorporating DZR brass body. The compression connection to be used with copper pipe BS EN 1057. Maximum working pressure 7.0 bar. Maximum operating temperature 95°C.
Range of in-line pilot operated level control valves with blue epoxy coated ductile iron bodies. The products have flow control facility controlled via a float operated valve and are supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C.
Range of inline pilot operated altitude control valves with blue epoxy coated ductile iron bodies and bonnets. The pilot system consists of spherical valves, in line strainers, needle valve, non-return valve, altitude gauge and a pre-set altitude control valve. The spring rating of the pilot 10-60ft (3 to 18m). Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of double swing gate, wafer, non-return valves with blue, black or red epoxy coated ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with (blue, black or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of adjustable, bronze in-line pressure reducing valves. VIT-20-PRBZ ½”, ¾” & 1” & 1¼” size have inspection ports on the outlet only. 2” to 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of in-line adjustable pressure reducing valves, with nickel plated DZR brass bodies and stainless-steel strainer. Various models are supplied with a pressure gauge (see model). Compression models are for use with BS EN1057 copper pipe. Maximum working pressure 16.0 Bar. Outlet pressure range: 0.8-6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure relief control valves with blue epoxy coated ductile iron bodies and supplied with auxiliary components including stainless steel pipe & fittings, spherical valves, bleed valve and a needle valve. Spring ratings of pilot valve are 0.35 - 3.5 bar, 0.7 - 5.5bar, 1.38 - 13.8 bar, 6.9 - 20.7 bar Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of spherical valves with nickel plated brass bodies and a chrome plated ball. The handle can either be a flat lever handle or a T handle (See models) Maximum working pressure 25.0, 30.0, 40.0, 50.0 Bar Maximum operating temperature 60.0°C
Wall mounted shower valve (chrome plated brass body) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of lockable, key operated, in-line spherical valves with brass bodies and nickel-plated brass ball. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of electronically actuated ball valves with brass bodies, chromium plated copper balls, PTFE and silica gel seals. Maximum working pressure 16.0 Bar. Maximum operating temperature 100°C.
Range of inline brass bodied or chrome plated brass bodied spherical valves, with a chrome plated brass ball and EPDM ‘O’-rings. SVB66MB and SV44MB models are lever operated. SV66MBC and SVT64MBC are screwdriver operated. The products are for use with PE-X pipe (manufactured to BS 7291-3), PB pipe (manufactured to BS 7291-2) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of PVC-U double union ball valves incorporating EPDM O-rings. Maximum working pressure 16.0 Bar. Cold water use only
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and hand wheel operating members. Maximum working pressure 25.0 bar (DN50-DN300) or 10.0 bar (DN400 only) Maximum operating temperature 85ºC
AMEXSA range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, having rate of flow control facility controlled via a pilot system. Spring ratings of pilot valve are 2 to 20 psi / 0.138 to 1.38 bar, 25 to 50 psi / 1.72 to 3.4 bar. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of gate valves incorporating bronze bodies and discs with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure; 20 Bar Maximum operating temperature; 85°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets and Bronze body, bronze wedge and handwheel. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of blue or green polyethylene coated ductile iron gate valves incorporating an EPDM Wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating bronze bodies and discs with PTFE seals. The valves operate via a non-rising spindle headwork that incorporates a wheel type operating member. Maximum working pressure; 20 Bar Maximum operating temperature; 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 10.0 Bar or 16.0 Bar Maximum operating temperature 40.0°C
Range of handwheel operated bronze bodied stop valves. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of push-fit, screw down stop valves with plastic bodies for use with copper pipe (manufactured to EN1057), PEX pipe (manufactured to BS 7291-3) and/or MDPE pipe (manufactured to EN 12201 (inserts required). For above and below ground use. Maximum working pressure:16.0 bar Maximum operating temperature: 20.0°C.
Range of inline plastic bodied screw down stop valves incorporating a non-rising spindle headwork with a dome type operating member. The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C.
Range of inlet control groups with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve set to 6bar. The outlet incorporates a single check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2. Pressure reducing range 1 bar to 6 bar Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of water conditioners with stainless steel bodies. Maximum working pressure 10 Bar. Maximum operating temperature 85°C.
'ZHR‐SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2025.8.27'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Ecocoat FBE Green Powder PFC/6018 (RAL 6018)& Ecocoat FBE Red Oxide Powder PFC/3000-Red Oxide'. Factory applied, green or red coloured epoxy coatings. Apply as per manufacturer’s Product Data Sheet revised ‘1st Jan, 2024’. Cure for 3 minutes at a metal temperature of 230°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Eurokote® 48-20 Brun Rouge’. Factory applied, red coloured, two-part epoxy coating. Mix resin and hardener in a 2.13:1 mass ratio and apply as manufacturer's TDS dated '10/12/2024'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'SEPTEMBER 2018 VERSION 1'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-P'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS 'BSS-P-D0002' dated '2025-1-10'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'L-01 GP Blue-grey Enamel'. Factory applied, blue-grey coloured Enamel coating. Apply as per manufacturer's TDS 'Version: 01', dated '2025-01-02'. Cure for 15 minutes@200°C and then fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing/firing conditions that appear on the approval. If the cure/fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BSS R/G System’. Grey coloured, factory applied, two-component epoxy coating comprising of ‘BSS Red and BSS Grey’. ‘BSS Red’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. ‘BSS Grey’ comprises of a base and curing agent which are mixed in a 3:1 volume ratio. Apply as per manufacturer's Product Data Sheet ‘BSS-D0003’, dated ‘2025-09-16’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitcote CM 210’. Site applied, two-part, grey coloured (once applied), Cementitious Waterproofing coating. Mix ‘CM 210 white’ liquid polymer and ‘CM 210 grey’ powder in a 1:3.6 weight ratio and apply two coats as per manufacturer's TDS 'UAE/0210/23/Z-1'. Cure Coat 1 for 3 hours@35°C and Coat 2 for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP 405’. Site applied, two-part,white coloured epoxy based Waterproofing coating. Mix 3.1 litres of the base with 0.9 litres of hardener and apply as per manufacturer’s TDS ‘UAE/0228/22/K’. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Proofex HDPE B125'. White coloured, extruded HDPE waterproofing membrane. For use with water up to 60°C.
'Seal Ring T11/T21'. Grey coloured, extruded PE seal ring. For use with water up to 85°C.
'Innogaz'. Black coloured, injection moulded, HDPE (PE100) electrofusion fittings. For use with water up to 60°C.
'XS10B & XRC30B'. Black coloured, extruded, Polyethylene materials. For use with water up to 23°C.
Grades manufactured in Marietta, Ohio: Radel R-5100 NT 15, R-5000 NT, R-5000 NT ECHO RP, R-5100 NT ECHO RP, & R-5100 NT (natural). Radel R-5100 BU 1197 & R-5100 BU1197 ECHO RP (blue coloured). Grades manufactured in Oudenaarde, Belgium & Marietta, Ohio Radel R-5100 GY 1037, R-5100 GY1037 ECHO RP, R-5100 GY1037LF & R-5100 GY1037 LF ECHO RP (grey coloured). Radel R-5100 BK 937 & R-5100 BK937 ECHO RP (black coloured). Radel R-5500NT & R-5100 NT15 ECHO RP (natural). Radel 5100 BU 1197 ECHO RP (blue coloured). Injection moulded, polyphenylsulfone materials. For use with water up to 85°C.
'Hepworth Qatar PPR 125 Pipe'. Green coloured (opaque), extruded PPR pipe. For use with water up to 85°C.
‘Udel P-3500 NT LCD, GF-110 NT, GF-120 NT, GF-121 NT, P-1700 NT 11 MR, P-1700 NT 11, GF-121 NT ECHO RP & P-3500 NT LCD ECHO RP’ (all beige translucent). ‘Udel P-1700 Grey 8057’ (grey coloured). ‘Udel P-1700 BK 937, P-1700 BK 937 MR, GF-120 BK 937, GF-121 BK 937, GF-121 BK 937 ECHO RP, GF-120 BK 937 ECHO RP & P-1700 BK937 ECHO RP’ (all black coloured). ‘Udel P-1700 WH 7407’ (white coloured). Injection moulded, polysulphone materials. For use with water up to 85°C.
'Polymax E708DW 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'HT5697-50'. Black coloured, injection moulded EPDM material. Shore hardness 67 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
‘EPDM-W 70817’. Black coloured, compression moulded EPDM rubber material. Shore hardness 80A. Tested in-radius size 0.98mm. For use with water up to 85°C.
'DLYY E6202'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.1mm. For use with water up to 23°C.
'WE-HR-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 0.99mm. For use with water up to 85°C.
'Dutral K-Co-054'. Black coloured, compression moulded EPDM materials. Shore hardness between 52A & 80A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EP500'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'KF011670FDA'. Black coloured, compression moulded, FKM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of injection moulded, VMQ rubber gaskets, seals, & `O` rings manufactured from the below compounds. The components are available in blue, green, grey, opaque (beige coloured), red, transparent & yellow. The numbers in the name of the compound indicates the shore hardness between 40 & 80. Tested in-radii sizes: Gaskets: 0.2mm - 5.0mm. Seals & `O` rings: 0.5mm - 5.0mm. S50B04E, S60B00E, S70B06E, S70B07E, S70V02E, S50V01E, S60O02E, S70O05E, S50O03E, S50O05E, S60O01E, S70O03E, S40A01E, S60A00E, S70A02E, S40R03E, S45R01E, S50R10E, S50R01E, S60R05E, S65R04E, S70R04E, S80R01E, S40R02E, S50R06E, S60R07E, S70R19E, S70R24E, S50T05E, S50T00E, S55T00E, S60T00E, S60T00T, S70T04E, S70T00E, S75T00E, S80T00E, & S70G01E. For use with water up to 85°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infrared sensor, and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure:8.0 Bar Maximum operating temperature:65 °C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated inlet valves, for WC flushing cisterns with plastic bodies and adjustable floats and a plastic flow regulator at the inlet. Maximum operating pressure: 10 bar. Maximum operating temperature: 23°C.
WC Cistern incorporating a side or bottom entry float operated inlet valve and a Syphon (Phantom S), Pneumatic Drop Valve (Phantom V) or Cable Operated Drop Valve (Phantom T) with full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or push button. Maximum working pressure 10.0 bar. Cold water use only.
W/C suite with pan (polyester) and a concealed flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a single flush drop valve for full flush volumes of up to 6 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 Bar. Cold water use only.
Range of spherical valves with DZR brass bodies, chromium plated brass balls, PTFE seats and EPDM rubber ‘O’-ring. The products also incorporate a ‘Y’- Patterned stainless steel strainer. Compression connection to be used with copper EN1057. AI-0396A062815CR incorporates an approved single check valve cartridge, verified by test - suitable for backflow protection against fluid category 2. Maximum working pressure: 25.0 bar. Maximum operating temperature: 100°C (model AI-0396A062815CR 65°).
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated stainless steel or brass bodies, see models). The flow is controlled by a solenoid valve that is activated via an infrared sensor. Temperature is controlled independently via a single lever operating member. The spout outlets incorporate plastic aerators. Supplied with hoses that incorporate stainless steel strainers and an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies). Flow is controlled by solenoid valves activated via an infra-red sensor and the temperature is controlled independently via single lever. The spout outlets incorporate plastic aerators. Maximum working pressure 8 Bar. Maximum operating temperature 65°C.
Range of T type thermostatic mixing valves with chrome plated DZR brass bodies. Compression and push-fit models for use with copper pipe manufactured to EN1057. Models 37.20122.015.CP,37.20122.022.CP, 37.21122.015.CP, 37.21122.022.CP, 37.21222.015.CP, 37.21222.022.CP, 37.20162.015.CP, 37.20162.022.CP have isolation valves and strainers on the inlet. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Spring loaded, resilient trim check valve cartridge with plastic body and EPDM O-rings. For insertion into fittings with specifically sized bores. Maximum working pressure: 16 Bar. Maximum operating temperature: 85°C.
‘TankBoost’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
‘TankBoost 5 bar’ range of cold-water storage cisterns, incorporating a float operated inlet valve. The C5 suffix models incorporate a Type ‘AB’ air gap with a meshed weir overflow (verified by test - suitable for backflow protection against Fluid Category 5). Cisterns with SUB in the model code incorporate a submersible pump and an expansion vessel. All models incorporate a screened warning pipe and dip tube. Models without a C5 suffix also incorporate a screened breather. Maximum working pressure 10.0 bar. Cold water use only.
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator and a swivel nozzle. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D22 | 22 mm | 10 bar | 85 °C | Gear, D22, Production date (DD/MM/YY) | Body | No | |||||
| D15H | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| D15C | 15 mm | 10 bar | 85 °C | Gear | Body | No | |||||
| R19H | 19 mm | 10 bar | 85 °C | Gear, 19H, Production date (DDMMYY) | Body | No | |||||
| R19C | 19 mm | 10 bar | 85 °C | Gear, 19C, Production date (DDMMYY) | Body | No |
Range of single hole, single outlet (swivel) combination taps assemblies (brass bodies - various finishes, see model) incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-down spray outlet with plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The cold inlet includes a loose chrome plated brass adaptor ½” BSP (M) x ½” BSP (F) incorporating an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The pull-out spray handset also incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies -various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator, (except for the 3259-XX models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| R BAS C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Indice | No | Non-rising spindle | C-plate | Flow Straightener | Pop Up |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MA3580-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584-Z | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3580PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3581PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3582PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator | |
| MA3584PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on body | No | Ceramic cartridge | C-plate | Aerator |
Models added December 2025: MA3580PC MA3581PC MA3582PC MA3584PC
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 305B1 | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Aerator | |
| 824B | Chrome | M10，female | 10 bar | 60 °C | XINYA,WRAS | Body | No | Ceramic cartridge | C-plate | Open Outlet |
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Two hole, single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The 2259-XX model incorporates an open outlet spout, all other models incorporate a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted two hole, single outlet (fixed) combination tap assembly (brass body, various finishes), incorporating ceramic cartridge headwork and single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119A-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119A-L25-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119A-L10-B | Matt black | G3/4(M) | 10 bar | 60 °C | AMG,WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 504109 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 5594201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | |
| 144201 | chrome | G3/4 | 16 bar | 60 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
Two-hole single outlet fixed combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with cross-top operating members and a manual diverter to shower outlet. The product is supplied with a shower hose, shower handset and plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator, (except for the 1259-XX models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M 07119-L25 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 07119-L25-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10 | Chrome | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | |
| M 08119-L10-B | Matt Black | G3/4(M) | 10 bar | 60 °C | AMG, WRAS | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| USH0228 | chrome | 3/4" x 1/2" offset unions | 10 bar | 60 °C | SONAS | on body | No | 1/4 Turn ceramic disk |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L446100MA | Tri-chrome | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100DH | Matt black | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| 1L446100SA1 | Brushed gold | 3/4" BSP (M) | 10 bar | 65 °C | WIDE | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HGLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS38 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, |
Range of three-hole, metal, single outlet (fixed) deck mounted, combination tap assemblies, (brass bodies - various finishes, see model), incorporating quarter turn ceramic disc headworks with lever or cross top operating members. The products are supplied with stainless steel braided PEX lined inter-connecting hoses. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Filling loop assembly consisting of an in-line isolation valve, an in-line double check valve assembly (suitable for back flow protection against fluid category 3) that incorporates an isolation valve and a stainless-steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
‘LSMRI’ range of copper-nickel press fittings (‘M’ type crimp profile) for use with copper-nickel ‘LSMRI’ pipe. Above ground use only. Maximum working pressures: Press fittings: 16.0 bar, LSMRI-PN6 Series flange: 6.0 bar, LSMRI-PN10/16 Series flange: 10/16 bar. Maximum operating temperature 99°C.
Multipipe range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
“D-“ and “E-“ range of 304 and 316L stainless steel press fittings, in either ‘M’ press profile (D- prefix models) or ‘V’ press profile (E- prefix models) for use with stainless steel pipe (316L & 304 manufactured to EN10312). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature: 85°C.
Range of in-line water meters incorporating bronze copper alloy bodies and EPDM O rings. Maximum working pressure 10.0 Bar Maximum operating temperature 30.0°C
Range of below ground water meter manifolds with a plastic body and a spherical valve at the inlet. Models incorporate an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. For use with PE80 blue pipe (manufactured to BS EN 12201). Maximum working pressure 12.5 bar. Cold water use only.
Range of electromagnetic flow meters with carbon steel bodies, NBR inner liner and stainless-steel electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.
Range of PVC lined flexible shower hoses with a black or silver finish. Open outlet use only. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FH SLRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 BB | Brushed Brass | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD01 GM | Gun Metal | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH SLRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| 225788 | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| RP3 FH SLRD01 C | chrome 3 | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Body | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD01 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD02 G | Gold | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, | |
| FH TDRD03 C | chrome | 1/2" BSP (F) | 5.0 bar | 85 °C | Bristan | Nut | No | Not Applicable | Not Applicable | Fixed Head, |
Two Fixed Head's with different finish and size as below FH SLRD01 C / BB / GM - (Dia 200mm) FH SLRD02 C - (Dia 250mm) FH SLRD03 C - (Dia 300mm) 225788 - (Wickes selling code for FH SLRD03 C) RP3 FH SLRD01 C - (Dia 200mm, chrome 3) FH TDRD01 C - (Dia 157mm) FH TDRD01 C / G - (Dia 200mm) FH TDRD03 C - (Dia 300mm)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WH51-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH51-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-8** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-10** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH52-12** | Various | BSP 1/2" (F) | Open outlet use only bar | 60 °C | Kind | Inlet connector | No | ||||
| JD-WH03** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-WH05** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA61** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA60** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA55** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No | ||||
| JD-HA54** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Body | No |
The suffixes of ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FBA015 | Bronze | 1/2" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable | |
| FBA020 | Bronze | 3/4" BSP (M) | 16 bar | 85 °C | Zhejiang Tasan Flow Tech logo, C84400, size, arrow, Date of manufacture(WWYY), WRAS | Body | No | Rising spindle | Not Applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SD2001 | 1/2" BSP (M) | 16 bar | 85 °C | SD and size | Body | No | |||||
| SD2001 | 3/4" BSP (M) | 16 bar | 85 °C | SD and size | Body | No |
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Pillar taps (chromium plated brass) with quarter turn ceramic disc headworks and cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with plastic back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 530 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | 1/4 Turn ceramic disk | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| RS2 3/4 C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | |
| 225916 | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Indice | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 HNK FL5 C CD | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| TAP1103 | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature: 60°C.
Range of EPDM braided hoses (various options) and optional end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of flexible corrugated stainless-steel tubing with white plastic covering. Compression connections are for use with copper pipe (manufactured to EN 1057). Captive nut end connections incorporate an EPDM gasket. 2BACa0504 prefix models incorporate a servicing valve (chromium plated brass body with brass ball) on the compression end connection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of air venting valves with a blue epoxy coated ductile iron body, plastic float, EPDM ‘O’-rings and seals. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 16 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 882 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk | |||
| 39 883 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | ½” BSP (M) | 10 bar | 70 °C | AXOR | on wall trim | Yes | 1/2 Turn ceramic disk |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of wall mounted, thermostatic blending valves incorporating ceramic disc diverter cartridges. Inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to verify backflow protection. Product also had manual override button, with variations of dome and single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Series of wall mounted, thermostatic mixer valve with brass bodies, diverter headwork that controls flow between one, two or three outlets (see model) with various type of operating member. The temperature is controlled independently via a thermostatic cartridge operating member with a manual override button. Inlets incorporate a stainless-steel strainer and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 55°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814109 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, | ||
| 814111 | chrome | 3/4” | 5 bar | 65 °C | KINEN | on body | No | 1/4 Turn ceramic disk | Shower Hose, Handset, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQDL1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 938HP | Chrome | 15mm Compression | 5 bar | 70 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 958HP | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, |
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. ISO models incorporate a servicing valve on each inlet. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wafer, lugged and flanged butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. F700L & F703L models incorporate a hand wheel operating members and F700G & F703G incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. The valves incorporate a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | GEAR, Model no. and Prodcution date (DD/MM/YY) | Body | No | |||||
| D35 | 35mm | 10 bar | 85 °C | GEAR, Model no | Body | No |
A range of non-return valve with blue epoxy coated ductile iron bodies, stainless-steel disc and EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs, PTFE stem gaskets and EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of in-line pressure reducing valves with either chromium plated DZR brass bodies, with manually adjustable outlet pressure ranges between 2.8bar to 3.2bar. Compression connections to be used with copper pipe EN1057 only. Maximum working inlet pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated). The products are supplied with auxiliary stainless-steel tubing, fittings, strainer, spherical valve and DZR pilot valve, DZR electrically actuated spherical valve. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 2.0 bar – 12.5 bar. Maximum operating temperature 80°C.
Range of pilot operated, adjustable, pressure reducing control valves with blue epoxy coated ductile iron bodies. The valves are supplied with a pilot valve, three spherical valves and a needle valve. Maximum supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 2.0 – 12.0 bar. Maximum operating temperature 80°C. Above ground use only.
Range of pressure relief valves (pre-set at 3.0 bar), with plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with nickel plated brass bodies, brass ball and PTFE seats. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of electrically operated motorised spherical valves incorporating brass bodies and stainless-steel balls. Maximum working pressure 20.0 bar. Maximum operating temperature: 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, brass wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of screw down stop valves incorporating brass or bronze bodies and EPDM gaskets. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of inlet control valves with DZR brass bodies. The valves consist of an adjustable pressure reducing valve set at 3.0 bar, pressure relief valve set at either 4.5, 6.0 or 8.0 bar. The valves also incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (natural, appear white)'. 'Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials. For use with water up to 85°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.3 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver2 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Corro Coat EP-F1003HW Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer's Technical Data Sheet dated '31 July 2018'. Cure for 4 minutes@245°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9001 Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's TDS/IFU 'number: 001', 'First Edition', revision date 'March 20, 2025'. Cure for 60 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BSS-LM'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's User Instructions 'File no. BSS-LM-D0001', 'Date: 9.20.2025'. Cure for 10 minutes@190°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Epilux 610 T Primer for use with Epilux 155 SF Topcoat'. Factory applied, white coloured (once applied) two-part epoxy coating. The topcoat can also be used alone, without the primer. 'Epilux 610 T Primer’ comprises of a base & hardener to be mixed in a 3:1 volume ratio and then applied as per manufacturer's TDS 'Ver.1 Aug 25'. Cure for 16 hours@25°C – 28°C, 60%±10% RH. 'Epilux 155 SF Topcoat' comprises of a base & hardener to be mixed in a 4:1 volume ratio and then applied as manufacturer's TDS 'Ver 1 Aug 25'. Cure for 7 days@25°C – 28°C, 60%±10% RH. For use with water up to 60°C. This material is only approved for the RH, mixing & curing conditions that appear on the approval. If the RH, mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1111 (Super Metal)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (dark grey, opaque paste) with Part B (light grey, opaque paste) in a 5:1 weight ratio and apply as per manufacturers IFU ’02-07-23’. Cure for 1 day@30°C or 5 days at 5 °C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 1331'. Grey coloured, site applied, two-component epoxy coating. First coat: Mix Belzona 1331 (white, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure for 6-8 hours@10°C or 3-4 hours@30°C then apply: Second coat: Mix Belzona 1331 (grey, opaque paste) parts A & B in a weight ratio of 2.2:1 and apply as per manufacturer’s IFU ’06-03-19’. Cure in accordance with manufacturer’s IFU ’06-03-19’, ‘Completion of the Molecular Reaction’ table, ‘Full mechanical/thermal loading or water immersion’. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Belzona 5811DW2 (grey)'. Grey coloured, site applied, two-component epoxy coating. Mix Part A (grey, opaque glossy paste) with Part B (orange, transparent liquid) in a 4:1 mass ratio and apply as per manufacturer’s IFU ’16-03-19’. Cure for 4 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless RF35 (2024) Coating System’. Site applied, grey coloured (once applied), two-part epoxy coating. The primer comprises of ‘Corroless EPF (2022) Primer Base Red’ and ‘Corroless EPF (2022) Buff Temperate Hardener’, to be mixed in a 1:1 volume ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 24 hours at 10°C. The coating comprises of ‘Corroless RF35 (2024) Base 00-A-01 Portland’ and ‘Corroless RF35 (2024) Hardener’, to be mixed in 5.5:1 weight ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 7 days at 10°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-U Yellow & Blue'. Fibre/NBR materials, available in yellow or blue colours, manufactured by calendaring. Tesnit BA-U Blue is for use with water up to 85°C. Between September 2025 and February 2026, Tesnit BA-U Yellow was for use with water up to 23°C. Between March 2026 and September 2030, Tesnit BA-U Yellow is for use with water up to 85°C. Store and handle in accordance with 'STORING & HANDLING INSTRUCTIONS, dated November 12, 2025'. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Grivory GVN-5H black 9915'. Black coloured, injection moulded PA 66 + PA 6I/X-GF50 material. For use with water up to 85°C.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Grivory HT1V-3 FWA natural and black 9225. Grivory HT1V-4 FWA natural and black 9225. Grivory HT1V-4 FWA grey 9489. Grivory HT1V-4 FWA grey-blue 4637. Grivory HT1V-5 FWA natural and black 9225. Grivory HT1V-5 FWA grey L1366.3 & Grivory HT1V-5 FWA grey 9616. Grivory HT1V-5 FWA grey L16760.2. Grivory HT1V-6 FWA natural and black 9225. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
'Tritan™ TX1501HF'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Tritan™ TX1001'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Tritan™HM1060'. Clear (translucent), injection moulded copolyester material. For use with water up to 85°C.
'Tritan™ TX2001'. Clear, injection moulded copolyester (PCTM) material. For use with water up to 85°C.
'Reno 100+'. Dual layered, extruded polyethylene pipe comprising of a black coloured inner and blue coloured outer layer. For use with water up to 23°C.
'Langboone HDPE Pipe P01'. Black coloured (with blue external stripes), extruded HDPE pipe. For use with water up to 23°C.
'Langboone HDPE Fitting F01'. Black coloured, injection moulded HDPE fitting. For use with water up to 23°C.
'Radius Systems PE100 Black Spigot Fittings'. Black coloured, injection moulded PE100 spigot fittings. For use with water up to 23°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
‘AQI380PRO’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’Load time’ cures set out in Table B4 of European Technical Assessment ETA 19/0127’, dated ‘28/02/2019’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’Load time’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 19/0127’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'51M7531'. Black coloured, injection moulded EPDM rubber 'O'-ring. Shore hardness 75. Tested in-radius 1.5mm. For use with water up to 85°C.
'SM177'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.56mm. For use with water up to 23°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'EP0E7001P-WRC'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'E7581'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
72401, 72501, 73401, 73501, 74401, 74501, 75401, 75501, 76401, 76501, 77401, 77501, 78401, 78501, 79401 & 79501. Range of press moulded, solid silicone rubber materials which are blue or red coloured. Shore hardness between 20 & 90. Tested in-radius size 1.0mm. for use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 4203801-1 | chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, |
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model) with a pull-out spray mechanism. Flow is controlled via a ceramic cartridge headwork with a single lever operating member incorporating an infra-red sensor on the swivel arm which operates a solenoid valve. The spout outlet incorporates a plastic aerator and a hand spray mechanism. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT103002000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT104001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator | ||
| TVT125001000xx | xx | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | handle | Yes | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVT105501110XX | See Below | 1/2" BSP M | 10 bar | 60 °C | Villeroy and Boch logo | Lever | No | Ceramic cartridge | Aerator |
Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Wall mounted two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headworks with cube operating member and incorporating a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 814110 | chrome | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, | ||
| 814112 | 814112 | 3/4" | 5 bar | 65 °C | KINEN | on body | No | Ceramic cartridge | Shower Hose, Handset, Fixed Head, |
Range of non-verifiable single check valve assemblies with DZR brass bodies. Maximum operating pressure 10.0 bar. Maximum operating temperatures: 430357-003, 430357-004 and 430357-006 models: 85°C, 430357-008, 430357-010, 430357-011 and 430357-012 models: 65°C.
Non-verifiable single check valve assembly with a stainless-steel body. Maximum working pressure 10.0 bar. Maximum operating temperature of 85°C.
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
In-line non-verifiable double check valve assembly with integral lever operated spherical valve, consisting of two spring loaded resilient trim check valve cartridges housed within a DZR brass body, verified by test (suitable for backflow protection against Fluid Category 3). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks and cross top operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste (not verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Non-rising spindle headworks (cast brass body) with EPDM ‘O’-rings and seat washer. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Non rising spindle headwork incorporating a brass body and NBR seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headwork assemblies with brass bodies, NBR ‘O’-rings and silicone gaskets. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with NBR rubber ‘O’-rings and silicone seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with EPDM seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar, Maximum operating temperature 85°C.
Range of ceramic cartridge headworks incorporating a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork & single lever operating member. The spout outlet incorporates a plastic aerator. The aerator also includes an integral stainless-steel strainer Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever or dome type operating members. The spout outlets are either open outlet or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Single hole tap(s) with a single outlet and a fixed spout. With a ceramic cartridge headworks and the spout incorporates a Flow Straightener. Product supplied with C-plate fixing type. Maximum temperature of 85 degrees Maximum pressure 5 bar.
Single hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and an optional flow regulator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and the spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L449200DH | Matt black | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200MA | Tri-chrome | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| 1L449200SA1 | Brushed gold | 1/2" BSP (F) | 10 bar | 65 °C | WIDE | Body | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 141701 | chrome | 1/2" BSP | 10 bar | 60 °C | KINEN | on body | No | Ceramic cartridge | Aerator |
Range of wall mounted, two-hole, single outlet, fixed, combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. Products incorporate a hand shower and a manual diverter to shower outlet. Models incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure: 6.0 Bar. Maximum operating temperature: 65°C.
Two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass & matt black finish) incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Spout incorporates a flow straightener. Product supplied with metal backnuts Maximum temperature 65 °C Maximum pressure 10.0 bar
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 503109 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 5593201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, | ||
| 143201 | shower set | G3/4 | 10 bar | 60 °C | KINEN | on body | Yes | Metal Backnuts | Shower Hose, Handset, |
Wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a dome type operating member and a manual override button. Each inlet incorporates a combined NBR washer and stainless steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self cancelling diverter to shower outlet and a plastic flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K005* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| K008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 20.189.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| 20.193.002 | Various | G 1/2" | 10 bar | 65 °C | Grohe | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
Where xxx denotes finish, can be replaced by: 002 – Chrome DC2 – Supersteel DA2 – Warm sunset AL2 – Brushed hard graphite A02 – hard graphit DL2 – brushed warm sunset GN2 – brushed cool sunrise A02 – hard graphite MS2 – satin steel GL2 – cool sunrise MS2 – satin graphite
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with stainless steel braided EPDM lined interconnecting hoses. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of chemical dosing equipment which incorporate self-closing valves and plastic bodies. The outlet of the injector incorporates a connection for injection of chemicals via venturi action and the inlets include stainless-steel strainers. Maximum operating pressure 9 bar. Maximum operating temperature 70°C.
Range of Socket weld, Click weld, Butt weld and Electro fusion fittings (see models), for use with ABN//INSTAL CT Faser RD Series 3.2 / SDR 7.4 & ABN//INSTAL CT Faser RD Series 5 / SDR 11 pipe. Maximum working pressure; (see models) Maximum operating temperature; (see models)
Range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *‐KJ600304 and *-KJ600316 stainless steel pipes. The "KJ6278" prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass compression fittings for use with copper pipes (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flange fittings with TP2 copper bodies, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ‘M’ profile copper press fittings with EPDM ‘O’-rings for use with copper pipes (manufactured to EN 1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
'Flomasta’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Range of end feed copper fittings for use with copper pipes (manufactured to EN 1057). The 5043G series and 5002G series models incorporate an EPDM ‘O’-ring on the captive nut connection. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Dual flush, WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Range of dual flush, WC outlet valves. Each valve is operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C.
Range of ultrasonic dry type water meters with brass bodies. Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C.
‘BECO Y’ range of ultrasonic water meters with plastic bodies, plastic transducers and silicone ‘O’-rings. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass bodied threaded fittings and a brass end feed fitting (C04069H00081A model only). The CL08069H192B4 model is chrome plated. The C04069H00081A model end feed fitting is for use with copper pipe (manufactured to EN 1057). The C04149H00191A model incorporates a plastic flow straightener. Maximum working pressure 10.0 bar, except for the C04149H00190A and C04149H00191A models which are open outlet use only. Maximum operating temperature 85°C.
Threaded adaptor (brass body) soldered with copper pipe and a range of thread extensions (chrome plated brass bodies). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of threaded fittings with either brass or chrome plated brass bodies. Maximum working pressure 40 Bar Maximum operating temperature 85°C.
CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.477.xxx | Various | G 1/2" | Open Outlet bar | 65 °C | Grohe | Shower faceplate | No | Fixed Head, |
Where xxx denotes finish, can be replaced by: 000 – Chrome DC0 – Supersteel DA0 – Warm sunset LS0 – moon white AL0 – Brushed hard graphite DL0 – brushed warm sunset GN0 – brushed cool sunrise GL0 – cool sunrise MG0 – satin graphite MS0 – satin steel A00 – hard graphite BE0 – polished nickel EN0 – brushed nickel
Range of shower handsets with ABS bodies (various finishes, see model). The spray outlet is either multifunction or single function depending on series. Open outlet use only. Maximum operating temperature 60°C.
Range of wall mounted or ceiling mounted shower arms with brass bodies (various finishes - see model). Maximum operating temperature 65°C.
Stainless-steel, angled, wall mounted overhead shower, incorporating silicone nozzles. Maximum operating temperature 85°C.
Range of In-line Y patterned strainers with ductle iron bodies (blue epoxy powder coated) and stainless-steel mesh. Maximum working pressure: 16 Bar Maximum operating temperature: 85 °C
Range of in-line Y pattern strainers with bronze bodies, forged brass cap and stainless- steel screen. Threaded end connections to BS21 ISO7/1 r/c (BSP taper – JIS B0203) Maximum working pressure 25 bar. Maximum operating temperature 23˚C.
Range of drain taps with a brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The BBFHUB-D – ½” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M3401 X XXX | VARIOUS | 1/2” BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/2 Turn ceramic disk | Metal Backnuts | Aerator & Flow Straightener | Flow Regulator Fitted, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of pillar taps (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with single lever operating members and flow regulator in the inlet (1/2” only). The spout outlets incorporate a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure: 10.0 Bar Maximum operating temperature: 85°C
Deck mounted pillar tap (chrome plated brass body) incorporating quarter turn ceramic disc headwork with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of shower hoses, multi-layered hose (various external finishes) with PVC inner liner, brass end connections. Open outlet use only. Maximum operating temperature 60°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of Stainless-Steel braided EPDM lined flexible hose assemblies with various end connections. For use with copper pipe manufactured to EN1057 Maximum working pressure; 16 Bar Maximum operating temperature; 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate push-fit isolation valves. Compression connection to be used with DM LLDPE pipes or PEX barrier pipe manufactured to BS7291-3. Maximum working pressure and maximum operating temperature 12 bar @cold water use only & 7 bar @ 65°C.
‘DG10E PF series’ of stainless steel braided EPDM lined flexible hose assemblies with EPDM ‘O’-rings or gaskets available with a variety of end connections. The DN10 bore 15mm push fit connection is also available with a screwdriver operated isolation valve. Push-fit connections are for use with copper pipes (manufactured to EN 1057) and PEX pipes (manufactured to BS 7291-3). Maximum working pressure 10.0 bar. Cold water use only.
‘FS4E Series’ 2 port, 3 port and 4 port nickel plated brass manifolds incorporating stop valves. The models include white operating members with either red, green or blue indices. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of automatic air release valves with blue epoxy coated cast iron bodies and plastic floats. Maximum working pressure 10.0 Bar 16.0 Bar, 25.0 Bar (see models) Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves, (brass bodies - various finishes), incorporating a thermostatic cartridge controlling the temperature. Supplied with either single lever or cross top operating members depending on model and with a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Wall mounted, bar type thermostatic blending valves (chromium plated brass) incorporating a quarter turn ceramic disc headwork, controlling and diverting the flow between overhead shower and handset, with dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Both inlets incorporate stainless steel strainer and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection Maximum working pressure 10.0 bar. Non-metallic materials and components comply with BS6920 at 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic mixing valves with between 1 and 2 outlets. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Models Mira Activate 1.1903.090, 1.1903.091, 1.1903.092 & 1.1903.093 incoporate a built-in pump. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves have a maximum working pressure of 1.0 bar. Maximum operating temperature 45°C.
Range of wall mounted thermostatic shower valves with brass bodies and trim set (various finishes - see model). Flow is controlled by a quarter turn ceramic disc headwork with various operating members. Temperature is controlled independently via a thermostatic cartridge with various operating members. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQ75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, | |
| TS75BAR1 | Chrome | 15mm compression | 10 bar | 65 °C | AQUALISA | Valve body | No | Non-rising spindle | Not Applicable | Shower Hose, Handset, |
AQ75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 704418 (shower handset) • ACY1008 (shower hose) TS75BAR1 Packed Products. Waterway contents are: • 704308 (shower valve) • 707540 (shower handset) • ACY1008 (shower hose)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV1 | Chrome | 5 bar | 65 °C | Aqualisa | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, |
AQRNDCV1 Packed Products. Waterway contents are: 705342 (shower valve) 704418 (shower handset) ACY1008 (shower hose) ACY1013 (wall outlet)
Range of thermostatic shower valves with a quarter turn ceramic disc headwork or a 2-way ceramic disc diverter headwork controlling the flow to 1,2 outlets with various operating members (see model). Temperature is controlled independently via a thermostatic cartridge with various operating members (see model) incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 Bar Maximum operating temperature 65°C.
Wapp mounted thermostatically controlled chrome finish shower valves. Incorporating an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides backflow protection). Maximum temperature 85 °C Maximum pressure 10 bar.
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, with stainless steel (CF8 or CF8M) discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of double flanged butterfly valves with blue, lavender or bright blue epoxy coated ductile iron bodies, EPDM seats and either white or red epoxy coated ductile iron or stainless steel discs. The products are supplied with bare shaft without operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of lugged butterfly valves incorporating black epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. From March 2023 the valves are also available with blue epoxy coated ductile iron bodies. The products are operated by: Gearbox or DRV gearbox operating members, or bare shaft without operating members. Maximum working pressures: RBV020-H models: 16.0 bar, RBV-S/PN25 models: 25.0 bar Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
Range of 2-way ceramic disc diverters/headworks (2 on, 1 off) with a plastic body to be housed in specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of in-line pilot operated control valves with blue epoxy coated ductile iron bodies, incorporating a solenoid valve. Maximum working pressure 12.0 Bar Maximum operating temperature 60.0°C
Range of dual plate non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘GNVP’ range of non-return valves with a white plastic housing. The product incorporates two test/drainage plugs. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Range of pressure reducing valves, manually adjustable outlet pressure from 0.5 bar - 6.5 bar, with DZR brass bodies and inspection ports on both the inlets and outlets. The valves incorporate plastic strainers. Maximum working pressure 25 bar. Maximum operating temperature 85˚C.
Range of pilot operated pressure reducing control valves (ranges of 0.7 to 7.0 bar or 1.5 to 15.0 bar) with ductile iron bodies (blue epoxy coating). Maximum working pressure: 16 Bar. Cold water use only.
Range of adjustable, pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coated) EPDM diaphragms, stainless steel tubing, isolation valves and needle valves. The product also incorporates both upstream and downstream pressure gauges. Maximum working pressure 10 Bar Maximum operating temperature 85°C Maximum outlet pressure 2 – 8bar
Range of pilot operated pressure reducing control valves with ductile iron bodies (blue polyester or epoxy coating) or stainless-steel bodies. Maximum working pressure 16 Bar (PR models) 12 Bar (PR-SC models) Maximum operating temperature 60°C Pressure ranges 0.35 bar-3.5 bar, 0.7 bar-5.5 bar, 1.38 bar-13.8, 6.9 bar-16 bar.
Pressure relief valve with a brass body. Pre-set at 2.5 bar relief pressure. Maximum operating temperature 110°C.
Solenoid valve with a brass body, EPDM diaphragm and ‘O’-rings. Maximum operating pressure 10.0 bar. Cold water use only.
Range of spherical valves nickel plated brass body with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
In-line spherical valve incorporating a chrome plated brass body and ball. Compression end to be used with copper pipe EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Spherical ball valve (screwdriver operated) incorporating a chromium plated brass body and ball. For use with BS EN 1057 copper pipe Maximum working pressure 16 Bar Maximum operating temperature 85°C
Range of spherical valves with various means of operation some via handle some with actuators, see models, comprising of a bronze valve body, spindle and ball valve, and EPDM O rings Maximum working pressure 16 bar Maximum operating temperature 90˚C.
Spherical valves incorporating a brass bodies and ball, PTFE seat, EPDM and NBR ‘O’-rings. The valve 8 718 657 822 incorporates a branch which is intended to connect to the primary circuit of a combination boiler. Maximum working pressure 10.0 Bar. Cold water use only.
Range of angled (S0273 and S0274 suffix models only) or in-line spherical valves with a nickel plated brass body, chromium plated brass ball and PTFE or EPDM seats. The products are either screwdriver operated or supplied with a T-handle (S0233BH-1 and S0233BH-2 models only). Compression ends are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass balls (chrome plated) and EPDM ‘O’-rings. For use with copper pipe to (EN1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Screwdriver operated spherical valves with brass or chrome plated brass bodies Compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 8.0 Bar Maximum operating temperature 80 °C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Push fit in-line spherical valve with plastic body, for use with PE-X pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe (manufactured to BS EN1057). Maximum working pressure/temperature: 12.0 Bar (cold water) and 7.0 Bar at 65°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle and a handwheel operating member. DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM wedge and a non-rising spindle. Maximum working pressure 16.0. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with bronze bodies, brass bonnets and DZR brass stems . The valves operate via a spindle headwork with hand wheel operation. Threaded end connections to BS21 ISO 7 /1 r/c (BSP Taper - JIS B0203). Maximum working pressure 25.0 bar. Maximum operating temperature 23oC.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. The valves operate via a non-rising spindle headwork with hand wheel, bevel gear, electric actuator & stem cap operator operating methods. Maximum working pressure 10.0 or 16.0 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with brass bodies, for use with copper pipe (manufactured to EN1057). Incorporating a either a handwheel or lockshield operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy ductile iron bodies and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies (see models) with T-type operating members. The 15mm, 22mm and 28mm compression sizes are for use with copper pipe (manufactured to EN 1057). The 20mm and 25mm compression sizes are for use PE pipes (manufactured to EN 12201-2). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies, incorporating EPDM gaskets. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass or chrome plated brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
‘Series 116’ range of balancing valves (DZR Brass body). Some models can be supplied with a thermometer (see model). The outlet of the 116144, 116154, 116244 & 116254 models incorporate an approved check valve cartridge, verified by test (suitable for backflow protection against fluid category 2). Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
Range of commercial, salt regenerated, electronically controlled ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
Electronically controlled, commercial ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only
'VAW1'. White coloured, compression moulded ceramic washer. For use with water up to 23°C.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyglass VEF'. Factory applied, two-part, off-white coloured, vinyl ester coating. Mix parts A & B in a 98:2 mass ratio and apply as per manufacturer's instructions '2/23' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaGrout-800'. Site applied, grey coloured Cementitious grout. Mix grout and water in an 8:1 weight ratio and apply as manufacturer's IFU 'Issue No.: 1', issued 'July 2024'. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SABIC® PP PHC 31'. White coloured, injection moulded polypropylene material. For use with water up to 23°C.
'B1-4773' Lip Seals and 'O' rings. Black coloured, EPDM components with shore hardness of 70. Compression moulded Lip Seals have an in-radius size of 2.7mm. Compression moulded ‘O’ rings have an in-radius size of 1.5mm. Injection moulded ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'70 EP111p' Lip Seals and 'O' rings. Black coloured, EPDM components with shore hardness of 70. Compression moulded Lip Seals have an in-radius size of 2.7mm. Compression moulded ‘O’ rings have an in-radius size of 1.5mm. Injection moulded ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'ECL/EP/50 & ECL/EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E7131'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'7571E'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'JHSX-02'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'VEV1'. Black coloured, compression moulded FKM seal. Shore hardness 70 A. Tested in-radius size 4.45mm. For use with water up to 23°C.
'FKM 70 514404'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
'Weld-On 719 Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '719-05-2024'. Cure for 8 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 705 ECO Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '705 ECO-09-2024'. Cure for 12 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of combination tap assemblies with a single outlet and fixed spout incorporating a manual diverter to shower. With a ceramic disc headwork and the spout incorporates a flow straightener. Maximum temperature 65 °C Maximum pressure 5.0 bar
Range of deck mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Range of wall mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use only
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 58 130 xx0 | Various | G 1/2" | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 42 540 xx0 | Various | G 1/2" | open outlet bar | 65 °C | AXOR | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 119 xx0 | Various | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 131 xx0 | VArious | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 152 180 | NA | G 1/2" | open outlet bar | 65 °C | hansgrohe | sticker only, marking will be on the finish set | Yes | Not applicable | Not Applicable | Open Outlet |
model 58131xx0 and 58119xx0 are identical in the water pathway, only difference is the cover plate design. model 58130xx0 and 42540xx0 are both composed of the finish set 58131xx0/58119xx0 and basic set 58152180, only difference is the marking on the faceplate 58130xx0= hansgrohe, 42540xx0= AXOR
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH001* | Various | ½” BSP (F) conical nut x ½” BSP(F) conical nut | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable | |
| SH002* | Various | ½” BSP (F) conical nut x M15x1 | For open outlet use only bar | 85 °C | WINSDRUM | On conical nut | No | Not applicable | Not Applicable | Not Applicable |
1) The products are interlock type 2) * denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1L325604DH | Matt black | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| 1L325604MA | Tri-chrome | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| 1L325604SA1 | Brushed gold | 15mm compression | 10 bar | 60 °C | WIDE | Body | No | 1/2 Turn Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 35H-5 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35H-F | 35mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35P-1 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 35PH-1 | 35mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40D-5 | 40mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40D-F | 40mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40H-5 | 40mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| 40H-F | 40mm | 10 bar | 65 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of near boiling water dispensers comprising of an install rail, under-counter boiler unit with a stainless steel tank and a countertop outlet (font). The install rail incorporates a water block, a double check valve assembly (suitable for backflow protection against fluid category 3) with an integral lever operated isolation valve and an adjustable pressure reducing valve (outlet pressure range 3.0 to 3.5 bar). The flow is controlled via a solenoid valve which is activated by a touch method at the outlet. The commercial model outlets (fonts) incorporate a safety button. The solenoid valve incorporates a plastic flow regulator. The countertop outlet (font) incorporates a plastic aerator. All models incorporate a separate vent outlet within the tap spout for the near-boiling water circuit. Maximum supply pressure to the install rail 16.0 bar. Maximum operating temperature 98°C. Cold supply only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D25-2 | 25mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge | ||||
| D39 | 39mm | 10 bar | 85 °C | company name (WANHAI), WRAS，model and date of manufacture (DD/MM/YYYY) | on body | No | Ceramic cartridge |
Model D25-2 and D39 are diverter with open/close function
Quarter turn ceramic disc headwork incorporating a brass body, EPDM and NBR ‘O’-rings and a silicone gasket. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 122 100 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 122 101 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 579 600 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 333 001 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 700 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 702 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable |
30 122 100 - Diameter= 25,4mm 30 122 101 - Diameter= 25,4mm 30 333 001 - Diameter= 25,4mm 30 746 700 - Diameter= 25,4mm 30 746 702 - Diameter= 25,4mm 30 579 600 - Diameter= 25,4mm
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 501102 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 501101 | Chrome | 1/2" BSP | 5 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591103 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 5591104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141102 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141101 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator | |
| 141104 | Chrome | 1/2" BSP | 12 bar | 60 °C | KINEN | on handle | No | Ceramic cartridge | C-plate | Aerator |
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies -various finishes, see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator, (except for the MYKCOR002 & BLKCOR002 models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Model (CH20x) is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure Bar Maximum operating temperature °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| KM FRZ BAS3.5 C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Operating member | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
Single hole, single outlet (swivel) combination tap assemblies, chrome finish(chromium plated brass), with a non-rising spindle and cross-top operating member(models 49944 & 88081) or ceramic disc headwork with lever type operating members(model 26251). The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 247031 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247032 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 247033 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | BODY | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Lever or Dome type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 526402 | Chrome (CHR) | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526407 | ANT/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526415 | BLA/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526408 | SGW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526981 | VGR/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526980 | SOW/CHR | 3/8" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator |
All surface finishes are not in contact with drinking water. The product structure (schedule of materials) of all versions are identical. Surface finish / color explanation: CHR - Chrome ANT - Anthracite BLA - Black Matt SGW - Silgranite White VGR - Volcano Grey SOW - Soft White
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members. The MYKCOR003 model incorporates an open outlet spout, all other models incorporate a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Models 91742, 805777 & 21775 incorporate a non-rising spindle headwork. Models 91742 & 805777 with dome type operating members Model 21775 with lever type operating members. Models 77174 & 805783 incorporate a quarter turn ceramic disc headwork with dome operating members. The fitting incorporates a manual diverter to the shower outlet The spout outlet incorporates a plastic flow straightener and the products are supplied with a shower hose, shower handset and metal back-nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| J THBSMVO C | Chrome | G 3/4" (M) | 10 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Flow Regulator Fitted, |
Two hole, single outlet fixed combination tap assembly (brass body - various finishes, see model) incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator, (except for the MYKCOR004(& BLKCOR004??? models). The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 PSNK C CD | Crome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
Note - Both Products are the same, one is wall mounted, one is deck mounted.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-L201** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| JD-200** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator | |
| SJS-L202** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-SP501 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Spout | No | Not applicable | Aerator | ||
| SJS-SP205 ** | Various | BSP 1/2" (F) | Open outlet only bar | 60 °C | Kind | Decorative plate | No | Not applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Uponor S-Press press fittings, Uni-X & Uni-C compression fittings for use with Uponor MLC pipe. Maximum working pressure 10.0 bar, maximum operating temperature 70°C.
‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Numepress' stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of copper press fittings with EPDM seals for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Fastwarm range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘Fastwarm’ range of U profile press fittings (nickel plated brass bodies) for use with ‘Fastwarm’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of copper capillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.
Range of plastic and DZR brass pushfit fittings for use with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipes (manufactured to EN 1057). Maximum working pressure 10.0 bar, except tank connectors which are open outlet use only. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except tank connectors.
'Flomasta' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.
Range of end feed copper fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of electromagnetic flow meters incorporating grey epoxy coated ductile iron bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of DZR brass metering stations supplied with red and blue test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.409.000 | chrome | G 1/2" | Open Outlet bar | 65 °C | Grohe | Faceplate | No |
Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
Range of Y-pattern strainers with DZR brass bodies and stainless steel strainers. The compression connection is for use with copper pipe to BS EN1057. Maximum working pressure 20 bar (BSP threaded models ½”-2”), 16.0 bar (compression models). Maximum operating temperature 85°C.
Range of `Y`-patterned strainers with either brass or DZR brass bodies, incorporating a stainless-steel mesh strainer. Maximum working pressure: 25.0 Bar (Models 36233, 36234, 36235, 36236, 36237 & 36238 ) or 16.0 Bar (Models 36230 & 36231 ) Maximum operating temperature 95°C. Strainers with compression connections are to be used with copper pipe manufacture to BS EN 1057. Strainers with M profile press-fit connections are to be used with copper pipe manufactured to BS EN 1057 & SS304 Stainless steel pipe manufactured to EN 10312.
Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of bib taps incorporating either brass or DZR brass bodies. The inlet and the outlet of the tap incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Wall mounted hose union tap (DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted hose union taps with brass bodies incorporating a rising spindle headwork with a T - handle operating member. Model HC-20252-15 incorporates a lockshield device at the base of the operating stem. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20205.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20255.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20275.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20365.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No |
Range of air venting valves with blue epoxy coated ductile iron or plastic bodies with plastic floats. Maximum working pressure 16.0 Bar. Cold water use only.
Range of automatic air release valves with blue epoxy coated stainless steel bodies and plastic or stainless-steel floats. Maximum working pressure 16.0, 25.0 or 40.0 bar (See Models below). Cold water use only.
Range of air vent valves with brass (covered with blue polyester coated ductile iron body) or plastic bodies and plastic floats. Maximum working pressure 16.0 bar (DAV KA & DAV A models) or 25.0 bar (DAV MP models). Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| * M980116 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 803250 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Body & Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 801528 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 803251 X XXX | VARIOUS | 15mm compression | 5.0 bar | 65 °C | PPI | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 801524 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 801525 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| * 800204 X XXX | VARIOUS | 15mm compression | 10.0 bar | 60 °C | PPI | Body | No | Single sequential | Metal Backnuts | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 804203 X XXX | VARIOUS | 15mm compression | 10.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Not Applicable | Shower Hose, Handset, Riser Rail, |
| * 801508 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 801509 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| * 801510 X XXX | VARIOUS | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | PPI | Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
The “*” is for a different Overhead Shower, Shower Hose or Shower Handset, which represent the letters A to Z X XXX Denotes the following: First X: Different handle The second, third & fourth XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of wall mounted, thermostatic blending valves incorporating ceramic disc diverter cartridges. Inlets incorporate an approved check valve cartridge, however the complete product has not been fully tested to verify backflow protection. Product also had manual override button. Model TPAQR25CH IS supplied with variations of dome and single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted thermostatic bar shower mixer (matte black plated brass), incorporating a ceramic disc diverter headwork controlling the flow between shower handset and overhead shower with a dome type operating member and a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless-steel EPDM strainer washers and approved check valve cartridges; (however, the complete product has not been fully tested to demonstrate it provides backflow protection). The product is supplied with screwdriver operated isolation valves, an overhead shower incorporating an EPDM washer at the inlet, shower handset, shower hose incorporating an EPDM washer at the captive nut and a stainless-steel EPDM strainer washer in the conical nut & riser rail assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted concealed thermostatic shower valves (brass bodies) incorporating single, double and triple outlets. Models (GR-AZ 50 & GR-AZ 50G) incorporate quarter turn ceramic disc headworks, models (GR-AZ 51 & GR-AZ 51G) incorporate two-way diverter cartridges & model (GR-AZ 53) incorporates a quarter turn ceramic disc headwork and two-way diverter valve. All models incorporate thermostatic mixing cartridges and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure Bar Maximum operating temperature °C.
A range either concealed or exposed wall mounted thermostatic mixing valves with brass bodies (exposed models are chromium plated). Models NU-089, NU-119 incorporate ¼ turn ceramic disc headworks. Model NU-119 & NU-109 incorporate a manual diverter with a shut off. All models incorporate a thermostatic cartridge that controls the temperature. The inlets of all models incorporate stainless steel filters and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of butterfly valves with blue epoxy coated bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and stainless-steel discs incorporating EPDM rubber seats. (DN40 - DN200) incorporate a lever type operating member and (DN250 – DN500) incorporates a hand wheel type operating member. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The LTDX71X-16Q DN40-150 size models are lever operated; all other models and sizes are gear operated. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 100°C.
Range of lever operated butterfly valves with blue epoxy coated cast iron bodies, stainless steel discs and EPDM ‘O’ rings and seals. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
3-way ceramic disc diverter with a plastic body, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of adjustable, bronze in-line pressure reducing valves. Models 131201015, 131201020 & 131201025 and model 131201032 have inspection ports on the outlet only. Models 131201050 & 131201100 sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Isolation valves with nickel plated brass bodies, chrome plated brass balls and EPDM O-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves incorporating (brass bodies - various finishes). Maximum working pressure 16.0 bar, 25.0 bar for model HC-A61055-15 Maximum operating temperature 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electrically (A20 & A150 series) or battery (E20 & E22 series) operated motorised spherical valves incorporating brass or stainless-steel bodies, stainless steel balls and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever, lockable lever or tee handles. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of plastic bodied inline, tee and angled spherical or servicing valves with EPDM ‘O’-rings. The products are either lever or screwdriver operated (see model). The products are for use with PE-X pipe (manufactured to BS 7291-3) and copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except AVT67665SM, AVT67661SM and AVT67445SM.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. Brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies and disks, with EPDM O seats. The valves are operated via a non-rising spindle headwork and hand wheel. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies. Maximum working pressure 17.24 Bar Maximum operating temperature 99.0°C
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with bronze, brass or DZR brass bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar GVBZ25 Series = 25.0 bar Maximum working temperature: 85C
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (GVBZR20, GVBZ20 and GVBZ prefix models). Bronze body, bronze wedge and lockshield (GVBZLS16 and GVBZLS20 prefix models). Brass body, brass wedge and handwheel (GVBZ16 model only). Maximum working pressure 20.0 bar & 25.0 bar (model GVBZLS16 DN50 only). Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of manually operated balancing valves incorporating bronze bodies, non-rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85ºC.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Scale inhibitor with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'PUC-SC15HD'. Grey coloured, pressed, sintered and ground Silicon Carbide seal. For use with water up to 85°C.
'PUC-SC15'. Grey coloured Silicon Carbide seal ring manufactured by pressing and sintering. For use with water up to 85°C.
'JSP/SF-Blue'. Factory applied, blue coloured epoxy powder coating. Spray apply coating when substrate is at a temperature of between 180°C & 190°C as per manufacturer's TDS '20200801 A2', dated '09-10-2025'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PENTALINE DI 750 BLUE'. Factory applied, two-part, blue coloured epoxy coating. Mix parts A and B in a 3:1 volume ratio and apply as per manufacturer's TDS 'Issue date: August 2023. Reference No - 01'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025-01'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Genesis FBE 5010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS issued 'August 2025'. Cure for 10 minutes@200°C. For use with water up to 23°C.
'VPC5022 Signal Blue FBE'. Factory applied, blue coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per manufacturer's Product Data Sheet 'VPC5022', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VPC8001 Gloss Black FBE'. Factory applied, black coloured Epoxy powder coating. Pre-heat substrate to 200°C and dip apply coating in a fluidised bed as per Product Data Sheet 'VPC8001', 'Revision: 1', dated '3 November 2025'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, two-part, black or white polyurethane coatings. 'Pentathane 1000 SD Black'. Mix parts A & B in a 2.5:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 65°C. 'Pentathane 1000 SD Off White'. Mix parts A & B in a 3:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 23°C.
'Abcite® 1060 DW Blue & Abcite® X60 DW Blue'. Factory applied, blue coloured thermoplastic powder coatings applied by dipping in a fluidised bed. Pre-heat substrate the coating is to be applied to for 12 minutes@280°C and apply as per manufacturer’s Application Guide ‘Version 04.05.2015’ (Abcite® 1060 DW Blue) or Technical Data Sheet ‘11/2023’ (Abcite® X60 DW Blue). Post-heat for 5 minutes@160°C. For use with water up to 23°C. These materials are only approved for the pre-heat and post-heat conditions that appear on the approval. If the pre-heat and/or post-heat conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MC-PROOF 4200 AE'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS dated 07.10.2025. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MC-PROOF 4210 AE'. Site applied, grey coloured (once mixed), two-component polyol and prepolymer based coating. Mix Part A (grey liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS '07.10.2025'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lewatit S 1568 & Lewatit S 1567'. Amber coloured, translucent ion exchange resins. For use with water up to 23°C.
'ZGC110DQ & ZGC108DQ'. Beige coloured ion exchange resins. For use with water up to 65°C.
'WL1225 Lubricant Soft Soap'. Amber coloured (translucent) lubricant. Apply as per manufacturer's IFU dated 22nd April 2025. For use with water up to 65°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'RP380s & RP361'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'RADILON® DT RV300RKC2 205 WT'. White coloured, injection moulded, glass filled Polyamide 612 material. For use with water up to 85°C.
'Menzolit SMC1000 3018-White'. White coloured, hot-press compression moulded Polyester Sheet Moulding Compound (SMC). For use with water up to 30°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 Version: 0, 19/11/2020’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JXPE100LP'. Blue coloured, extruded HDPE pipe. For use with water up to 23°C.
'SAB A16 Compression Fittings'. Black coloured, compression fitting bodies, injection moulded from polypropylene (PP-B). For use with water up to 60°C.
'PTFE Thread Seal Tape 201 (white), 202 (pink), 203 (yellow), 204 (blue) & 205 (grey)'. PTFE tapes, manufactured by extrusion, stretching and calendaring, available in a range of colours. For use with water up to 85°C.
'DF1212'. White coloured, extruded PTFE tape. For use with water up to 85°C.
‘662016, 662014, 662062/SF (251VM), 662062-10PK/SF (523VM), 662061-10PK/SF (113VM)’. White coloured, PTFE tapes manufactured by calendering. For use with water up to 85°C.
‘AH Codes: 662016CB & 662014CB, CB Codes: 571983 & 571984’. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'SPIT EPCON C8+ XTREM'. Site applied, brick coloured (once mixed), chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MBMS0715'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.35mm and 5.0mm. For use with water up to 85°C.
'XX-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'NK8650W-EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 65. Tested in-radius size 1.1mm. For use with water up to 65°C.
'JSP/SF-02'. Black coloured, compression moulded EPDM rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
'EW-001'. Black coloured, compression moulded EPDM material. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 23°C.
'Griffon WDF-05®'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6306959 20251027'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AQRNDCV2 | Chrome | 5 bar | 80 °C | AQUALISA | shower valve | No | Ceramic cartridge | Not Applicable | Not Applicable | Shower Hose, Handset, Fixed Head, |
AQRNDCV2 Packed Products. Waterway contents are: SDCV.002 (Valve) 704418 (handset) ACY1008(hose) ACY1013(wall outlet) ACY1002(fixed arm) 704426(top shower)
Range of in-line, non-verifiable single check valve assemblies with DZR brass bodies and spring loaded, resilient trim check valve cartridges. For use with copper pipe (manufactured to BS EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Non-verifiable single check valve assembly consisting of a spring loaded, resilient trim, single check valve cartridge within a DZR brass body. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non verifiable double check valve assembly incorporating a screw down stop valve, with nickel plated DZR brass body. Maximum working pressure 10 Bar. Cold water use only.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. The products incorporate a drain port between the cartridges. Compression connection for use with copper pipe to BS EN1057 Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (brass bodies – various finishes) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, bidet combination tap assembly (stainless steel body -various finishes) incorporating a fixed spout with swivel nozzle. The products incorporate a ceramic cartridge headwork with single lever operating member and the spout outlets a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M28DF-2 | 28mm | 5 bar | 85 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk |
Range of quarter turn ceramic disc headworks incorporating brass bodies (HW-12, HW -34, HW - 38) or plastic body (HP-12). Maximum working pressure 12 Bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges incorporating plastic bodies and stainless-steel filters. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Single hole, single outlet (swivel) pull down spray combination tap assembly (chromium plated brass body) with a ceramic cartridge headwork and single lever operating member. The product incorporates a pull-down spray with a plastic aerator, which also incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 550 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 551 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 557 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 558 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 559 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 560 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 561 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 580 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 584 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 585 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 589 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | ||
| 71 593 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 594 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Pop Up | ||
| 71 598 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | ||
| 71 526 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 527 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 528 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | |||
| 71 529 xx0 | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator |
Where xx0 denotes the surface finish. It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 003 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | ||
| 10 001 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 007 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 102 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator | Pop Up | |
| 10 103 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | AXOR | on the body | Yes | Ceramic cartridge | Metal Backnuts | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 681104 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 681101 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 691104 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 691101 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator | |
| 891105-1 | chrome | ½” BSP (F) | 5 bar | 60 °C | KINEN | On handle | No | Ceramic Cartridge | C-plate | Aerator |
Range of single hole, single outlet fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates an plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar Maximum operating temperature 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Model 33501662 is supplied with a pop-up waste – not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Single hole, single outlet (fixed) over the rim bidet combination tap assembly (chrome plated brass). Incorporating a ceramic cartridge and single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste set – not verified by test. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 65.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 554 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | Pop Up | ||
| 71 564 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | Pop Up | ||
| 71 870 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 871 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 857 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator | |||
| 71 878 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 3/8 | 10 bar | 60 °C | hansgrohe | on the body | Yes | Ceramic cartridge | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K003* | Various | ½" BSP (F) | 10 bar | 65 °C | WINSDRUM | On wall plate | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| K004* | Various | ½" BSP (F) | 10 bar | 65 °C | WINSDRUM | On water outlet | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic combination aerator (63868-00X, 63868-01X) and 2 separate plastic aerators for the hot & cold outlet or filtered outlet (63869-00X, 63869-01X). Maximum working pressure: 5.0 bar Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SJS-WB100* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| SJS-WB200* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| SJS-WB101* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WB743* ** | Various | BSP 1/2" (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | Ceramic cartridge | Metal Backnuts | Aerator | Interconnecting Hoses, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SJS-WB102* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| SJS-WB202* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB742* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-2* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720065 | Chromed | BSP 1/2" (M) | 10 bar | 85 °C | MVI | Rear of body | No | Non-rising spindle | Metal Backnuts | Flow Straightener | |
| 2720095 | Chromed | BSP 1/2" (M) | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TRLS01 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| TRLS10 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS06 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS07 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
Finishes available: Brass, Chrome, Nickel, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Dark Nickel, Vintage Brass, Gold, Matte Gold.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-792* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle, spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-742-2* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-702* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| JD-704* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of three-hole, metal, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Three-hole, metal, single outlet (fixed) combination tap assembly (chromium plated brass). The product incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with stainless steel braided PEX line connecting hoses. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of ceramic filter cartridges with a plastic body. Cold water and open outlet use only.
Range RP of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of DZR brass compression fittings for use with 'Wavin PE-RT Pipe'. Maximum working pressure:20 bar Maximum working temperature:23°c
Range of polypropylene push-fit fittings. The 20, 25 and 32mm sizes are for use with MDPE Pipe (manufactured to BS EN 12201-2). The 15, 22 and 28mm connections are for use with the following pipes: PEX (manufactured to BS 7291-3) for 15, 22 and 28mm sizes. PB (manufactured to BS 7291-2) and Copper (manufactured to BS EN 1057) for 15 and 22mm sizes only. Maximum working pressures: UG601B model: 16.0 bar. All other models: 12.5 bar. Cold water use only.
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
“>B<Press NZ” range of press fittings incorporating copper (EN12165 CW024A) or copper alloy (CC499K-DW) bodies. For use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of under counter, vented, electric instantaneous (near boiling) water heaters with a stainless steel tank and silicone seals. Maximum operating temperature 98°C.
Range of water meter measuring capsules with brass bodies. Maximum working pressure 16.0 bar. Please refer to model for maximum operating temperature.
Range of high flow water meters with black epoxy coated ductile iron bodies and EPDM gaskets. Maximum working pressure; 16 Bar Maximum operating temperature Cold water only
Range of water meters with a brass body and plastic strainer on the inlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C
Range of electromagnetic flow meters with stainless steel bodies, EPDM inner liner and SUS316L electrodes. Maximum working pressure 16 Bar. Maximum operating temperature 40°C.
Range of pump docking manifolds with plastic bodies. Maximum working pressure: 5.5 bar. Cold water only.
‘Hansen True Fit’ range of black coloured, plastic threaded fittings. Maximum working pressure 1/8” – 2” BSP: 16.0bar, 2½” BSP: 12.0bar, 3” – 4”: 10.0bar. Cold water and above ground use only.
Range of in-line flow sensors incorporating either brass (type 230, 235 & 236) or plastic (type 200 & 210) bodies & EPDM ‘O’-rings. Maximum working pressure 12.0 Bar Maximum operating temperature 100.0°C
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 51OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52CS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52DS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6301-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6302-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6303-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 63OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6300-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OS-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OH-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator |
** Representative all models are available with the following finish code: CP-Polished Chrome BN-Brushed Nickel MB-Matte Black ORB-Oil Rubber Bronze PB-Polished Brass WP-Weathered Pewter BB-Brushed Brass
Range of overhead shower outlets with (stainless steel bodies - various finishes). The inlet incorporates a combined EPDM washer and an approved check valve cartridge: however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: Open outlet use only. Maximum operating temperature 65.0°C
Range of shower handsets with (plastic bodies - various finishes), incorporating an approved single check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: Open outlet use only Maximum operating temperature: 60°C.
Range of shower handsets with chromium plated plastic bodies. Maximum operating temperature 65.0°C Open outlet use only
Shower handsets with chromium plated plastic bodies and a plastic flow regulator in the inlet. Maximum operating temperature 65°C. Open outlet use only.
Range of wall or ceiling mounted shower arms with brass bodies (various finishes). Maximum operating temperature 65°C. Open outlet use only.
Range of shower handsets with brass body available in various finishes. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless steel mesh strainer. Maximum working pressure 20 bar. Maximum operating temperature 85°C
Range of DZR brass and brass bodied in-line Y-Stainers with a stainless-steel mesh. Compression models for use with copper pipe to BS EN1057. Maximum working pressure 10 Bar Maximum operating temperature 60°C.
Range of self-closing taps (chromium plated brass) incorporating a push button headwork with a dome type operating member. The inlet hoses each incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Range of self-closing taps (chromium plated brass) with a dome type operating member. The spout outlet incorporates a plastic aerator. Model 02 122 06 99 model is supplied with a metal backnut. Maximum working pressure 10 bar. Maximum operating temperature 65C
‘TAQ PEX’ range of PEX lined flexible hose assemblies with either stainless steel braiding or grey polymeric (PET - Polyethylene terephthalate) braiding. G3/8" captive nut connection includes an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Hoses with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel, interlocked shower hoses with EPDM liner and O-rings. Open outlet use only. Maximum operating temperature 65°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. The captive nut end connections incorporate a washer, the M10 connection incorporates an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Excelsior Range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
Range of unvented heat pump storage cylinders which consist of an air-source heat pump sitting on top of the tank with either no internal coil (model numbers ending without S) or a factory fitted single internal coil (model numbers ending with S). The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C and an stainless steel immersion heater and titanium alloy anode. The product is not supplied with an inlet control group (safety kit). Maximum operating temperature 70°C. Maximum working pressure (primary & secondary circuit) 5.5 bar.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 681 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 1/2 (offset) | 10 bar | 70 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | Not Applicable |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 86005640 | Chrome | 15mm compression joint | 10 bar | 80 °C | TRITON,86005640 | Handle/ body | No | Ceramic cartridge |
Wall mounted, concealed shower valve (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating members and a manual diverter to shower outlets with a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, manually operated, concealed shower valves (stainless steel bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Wall Mounted shower valve with shower hand-set, hose with riser rail and overhead shower, available in various finishes. A05846 incorporates a single sequential headwork, all other models incorporate 1/4 turn ceramic disc headwork. Some model include a flow regulator. Models A5846 & A05847 maximum pressure 10.0 bar. All other models maximum pressure 5.0 bar Maximum temperature all models 65°C
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a ceramic disc diverter (models SD4373-2S) with various operating members. A quarter turn ceramic disc headwork (models SH40001-2, SD4373S) or 2 quarter turn ceramic disc headworks (model SH40001). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate backflow protection. Models SH40001-2, SH40001 incorporate stainless steel strainers. Supplied with a shower hose, shower handset, riser rail & overhead shower outlet (models SD4373-2S, SH40001). SD4373S incorporates a shower hose, shower handset & riser rail. SH40001-2 incorporates an overhead shower outlet Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C. Model SH40001 Maximum operating temperature 60°C
Wall mounted, concealed, thermostatic blending valve incorporating a thermostatic cartridge with a dome operating member and supplied with a trim set. Each inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, ductile iron or stainless steel discs with EPDM seats and a lever operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Combined temperature and pressure relief valves with a DZR brass body, pre-set at 7.0, 10.0 or 15.0 bar. Maximum working pressure See models Maximum operating temperature 90.0°C
Combined temperature and pressure relief valves pre-set at 7.0 or 10.0 bar (See models) with a DZR brass body. The valves incorporate lever easing gear. Maximum working pressure: See models. Maximum operating temperature 85.0°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure: 11.0 Bar (model O2010.G15) and 9.0 Bar (model O2010.G20). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure: 11.0 Bar (model O1011.G15) and 9.0 Bar (model O1011.G20). Cold water use only.
Range of pilot operated flow control valves with blue epoxy coated ductile Iron bodies and EPDM ‘O’-rings. Auxiliary components include stainless steel tube with fittings and ball valves. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet, manually operated flow control valve (brass body) incorporating a quarter turn ceramic disc headwork. Maximum working pressure:10BAR Maximum working temperature:65°c
In-line, manually adjustable pressure reducing valve with brushed chrome plated DZR brass body, for use with copper pipe (manufactured to BS EN 1057). Supplied with a pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of DZR brass and nickel plated DZR brass pressure reducing valves with a pressure gauge connection. Compression connection to be used with copper pipe EN1057. Outlet pressures adjustable between 1.5 & 7.0 bar (pre-set at 3.0 bar). Maximum working pressure 16.0 bar. Maximum operating temperature of 85°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies, Stainless-steel filter, EPDM ‘O’-rings and diaphragm. The valves have an adjustable pressure reducing facility controlled via a pilot valve (see note), with auxiliary components including stainless-steel tubing and fittings, strainer and stainless-steel spherical valves. Maximum working pressure 16.0 Bar. Maximum operating temperature 60°C.
Range of normally closed (L182 models) solenoid valves with brass bodies. Maximum working pressure 16.0 bar: 12900 Maximum working pressure 12.0 bar: 12903 & 12906 Maximum working pressure 10.0 bar: 12909 ,12912 & 12915 Maximum operating temperature 85.0°C
Range of bistable solenoid valves incorporating a plastic body, EPDM diaphragm and ‘O’-rings. The 51.005.101 model incorporates a stainless-steel strainer on the inlet. Maximum operating pressures: 51.005.100: 5.0 bar, 51.005.101: 10.0 bar. Maximum operating temperature 70°C.
Pulse controlled/latching (bistable) solenoid valves with a plastic body and integral stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Solenoid valve with a plastic body, incorporating an EPDM diaphram and NBR sealing rings. The inlet incorporates a plastic filter. The pushfit connections are for use with LLDPE pipes (manufactured to DIN 8072). Maximum working pressure 8.0 bar. Cold water use only.
Range of electrically or battery operated motorised spherical valves incorporating brass, DZR brass or stainless-steel bodies, stainless steel balls and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball, (DZR brass body and ball on 40 bar models). Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of spherical valves incorporating bronze bodies, chromium plated brass ball, PTFE seat and lever operating members. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, brass ball and PTFE seats. Valves with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of nickel plated brass servicing valves, and nickel plated brass or brass (SD1001 models only) spherical valves. All products incorporate a chrome plated brass ball. SD6017, SD6003 and SD3008 valves are screw driver operated. SD6012, SD4001 and SD1001 valves are lever operated. SD4003 valves have butterfly operating members. The compression and pressfit connections are for use with copper pipes (manufactured to EN1057). Pressfit connection jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressures: SD3008 valves: 10.0 bar, SD6017, SD6012 and SD1001 valves: 16.0 bar, SD4003, SD6003 and SD4001 valves: 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated and butterfly handle spherical valves with nickel plated brass bodies and chromium plated brass ball. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
2014 Range of stainless steel inline spherical valves incorporating a stainless-steel ball, PTFE gasket and seat with a lever type operating member. Maximum operating pressure 62 bar. Maximum operating temperature 23°C
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with brass or DZR brass bodies incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves operate via a hand wheel. Maximum working pressure 16 Bar (For model FTBGW-16). Maximum working pressure 20 Bar (For model FTBGW-20S). Maximum working pressure 25 Bar (For model FTBGW-25). Maximum operating temperature 85°C.
Range of gate valves incorporating cast iron bodies (blue epoxy coated), EPDM coated wedges and non-rising spindles with hand wheel operating member. Maximum working pressure 10.0 bar (Z45X-10Q model). Maximum working pressure 16.0 bar (Z45X-16Q models). Maximum operating temperature 80°C.
Screw down rising stop valve (nickel plated DZR brass) incorporating a dome type operating member. Maximum working pressure 10.0 Bar Cold water use only
Range of stop valves with brass bodies and T-type operating members. Compression connecitons are for use with copper pipes (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 10.0 Bar Maximum operating temperature 100.0°C
Range of magnetic scale reducers with metal bodies, for use with copper pipe (manufactured to EN 1057). Maximum working pressure 12 Bar. Maximum operating temperature 30°C.
Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.
'YHR-GFS Enamel'. Factory applied, dark blue coloured Enamel coating. Mix enamel powder with water in a ratio of 7:3 and apply two coats as per manufacturer's TDS 'YHRGFS2504', version 'V0', dated '2025/3/27'. Cure for 20 minutes@120°C and fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the mixing, curing & firing conditions that appear on the approval. If the mix and/or cure and/or fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'thoenes BA110'. Green coloured NBR/fibre material manufactured by calendering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'thoenes BA120'. Blue coloured, fibre/NBR material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'SC1100UR'. Colourless, injection moulded polycarbonate material. For use with water up to 60°C.
'D.63 Spigot and Electrofusion Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 23°C.
'Reno 100'. Black coloured (with blue external stripes), extruded polyethylene pipe. For use with water up to 23°C.
'KE-551E-U, KE-561E-U, KE-571E-U & KE-581E-U, natural'. Natural (appears white, translucent), extruded VMQ silicone rubber cylinders. Shore hardnesses 50, 60, 70 & 80 A respectively. Tested in-radius sizes between 0.9mm and 21.13mm. For use with water up to 85°C.
'1922, 1923 & 1933 washers'. Red coloured, injection moulded silicone rubber washers. 1923 washers have an in-radius of 1.59mm. 1933 washers have an in-radius of 0.83mm. 1922 washers have an in-radius of 1.23mm. For use with water up to 85°C.
Range of floor mounted, single hole, single outlet combination tap assemblies (stainless steel body – various finishes) incorporating a ceramic cartridge headwork and manual diverter to shower outlet, with single lever operating members. The spout outlets incorporate a plastic aerator. Product incorporates an approved check valve cartridge at the inlet; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset is not supplied with this product. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
'CORZAN® 3236 GRY 211'. Grey coloured, injection moulded CPVC material. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 8 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW105112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW103112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW125003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008002XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008003XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW111002001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106010001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW112007001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW116001000XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel).
Wall mounted, fixed, spout outlet (brass bodies – various finishes) incorporating a plastic flow straightener. Maximum operating temperature 60°C Maximum working pressure: Open outlet use only
Range of shower kits with a shower hose, handset and shower rail. Open outlet use only Maximum operating temperature 60.0°C
Range of wall mounted, manually operated, concealed blending shower valves (stainless steel bodies – various finishes) incorporating a ceramic cartridge headwork, with single lever operating member and 2 or 3-way diverter, controlling the flow and temperature. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH-T8089D-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T8089-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T80810-** | Various | ¾” to ½” Offset Unions. | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk | |||
| SH-T80810D-** | Various | 15mm compression union | 5 bar | 75 °C | SHANHU | BODY | No | 1/4 Turn ceramic disk |
-**Represents the following different surface treatments: 1.PB-ARTISAN BRASS 2.EB-Matte black 3.CP-CHROME
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-AT2** | Various | BSP 1/2" (F) x BSP 3/4" (F) | 10 bar | 60 °C | Kind | Body | No | 1/2 Turn ceramic disk | Not Applicable | Not Applicable | |
| JD-AT3** | Various | BSP 1/2" (F) x BSP 3/4" (F) | 10 bar | 60 °C | Kind | Body | No | 1/2 Turn ceramic disk | Not Applicable | Not Applicable |
Note: ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TVS106353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS103353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT127001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS112003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS125003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS104353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS107005000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS106353113xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT111001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS122002000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS108008000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS105353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS00035100000 | null | 1/2" F | 10 bar | 60 °C | null | null | Yes | Ceramic cartridge | null | null | null |
TVS00035100000 – Vi-Box is used in conjunction with all of the models. Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 99078-H | 25mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99014-H | 32mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| G22151-N | 34mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99150-H | 35mm Ø | bar | 65 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99095-H | 28.5mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99090-H | 28.5mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable |
The cartridges 99078-H and 99014-H are re-approvals of certificate 2007006 (Expiry date: 31/07/2025) The cartridges G22151-N, 99150-H, 99095-H, 99090-H are on the same family and we would like to add to the same certificate.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720067 | Chromed | 1/2" Captive nut | 10 bar | 60 °C | MVI | Body | No | Ceramic cartridge | C-plate | Aerator |
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies incorporating a ceramic cartridge headwork with a various operating member. The product incorporates a pull-out spout with a plastic aerator. Maximum working pressure 6 Bar Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 052 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 051 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 053 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 054 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 055 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Single hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating a ceramic cartridge with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 32002 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41802 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 41802L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 60℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | Aerator | |
| 81202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81202L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81402 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 81402L | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate | ||
| 91202 | chromium plated | ½” BSF (F) Captive nut | 10bar bar | 85℃ °C | Bokeya | on body | No | Ceramic cartridge | C-plate |
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies -chrome finish) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) combination tap assemblies (brass bodies -chrome finish) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 34 010 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Lever Operated Pop-up | |
| 34 016 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Lever Operated Pop-up | |
| 34 017 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Open Outlet | |
| 34 127 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Open Outlet |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WB791* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB791H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1020* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1020H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1021* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1021H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1022* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1022H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT053 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT014 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT015 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT004 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | Non-rising spindle | C-plate | Aerator | |
| SL-KT40602R | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT032 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Side of body | No | Ceramic cartridge | C-plate | Aerator | |
| SL-KT054 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT30602W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT40202L | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Flow Straightener |
Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720032 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720034 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720068 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 519413 - MILI RH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 517742 - MIDA RH HP CHR | Chrome | 3/8" | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 528156 - MIDA ECO RH HP BL | Black matt | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| 519414 - MILA RH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526657 - MILA RH HP BL | Black matt | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 528154 - MILA ECO EH HP CHR | Chrome | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| 528155 - MILA ECO EH HP BL | Black | 3/8” | 5 bar | 60 °C | BLANCO | Body | Yes | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WK794* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK795* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK1034* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK305* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB792* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
* stands for the different handle A, B,C and D ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K006* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| B006* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| B007* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| K012* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On body | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | |
| K013* | Various | ½" captive nut | 5 bar | 65 °C | WINSDRUM | On body | No | Ceramic cartridge | Not Applicable | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Floor standing, single hole, single outlet (swivel) combination tap assembly with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT40602W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company LOGO | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| SL-KT40502W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company LOGO | Rear of body | No | Non-rising spindle | C-plate | Flow Straightener |
Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720055 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| 2720060 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Open Outlet | |
| 2720062 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Open Outlet |
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, chrome and black finish - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes brass bodies), incorporating quarter turn ceramic disc headworks. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted, two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a quarter turn ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Range of two hole, single outlet (fixed) chrome combination tap assembly (brass bodies), incorporating quarter turn ceramic disc headworks. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) chrome combination tap assembly (brass bodies), incorporating quarter turn ceramic disc headworks. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) chrome combination tap assembly (brass bodies), incorporating quarter turn ceramic disc headworks. The spout outlet of model L-BF incorporates a plastic aerator. Capable of achieving AUK2 Tap Gap. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed deck mounted combination tap assembly with a brass body and Chrome finish. Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2437 | Chrome plated | 1/2" | 5 bar | 60 °C | DELABIE | Handle | Yes | Single sequential | Not Applicable | Flow Straightener | Flow Regulator Fitted, |
| 2437S | Chrome plated | 1/2" | 5 bar | 60 °C | DELABIE | Handle | Yes | Single sequential | Not Applicable | Flow Straightener | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-ATS413* ** | Various | ¾” x ½” BSP (M) offset unions | 10 bar | 60 °C | Kind | Handle | No | 1/2 Turn ceramic disc | Not Applicable | Aerator | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of two hole, single outlet (fixed) combination tap assemblies (various finishes brass bodies), incorporating quarter turn ceramic disc headworks with a manual diverter to spout outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a two-way diverter headwork that controls the flow between the spout outlet and shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic mixing cartridge, the incorporates a manual override button. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Two hole, single outlet fixed combination tap assembly, brass body with chrome finish. Incorporating quarter turn ceramic disc headworks with cross type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts, and include shower Hose & Handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet fixed combination tap assembly, brass body with chrome finish. Incorporating quarter turn ceramic disc headworks with cross type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts, and include shower Hose & Handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Deck mounted two hole chrome combination tap assembly with 1/4 turn ceramic disc headworks and lever type operating members, the spout incorporates a plastic flow straightener. Supplied with metal backnuts, shower hose & handset. Maximum pressure 5.0 bar Maximum temperature 60 °C
Range of two-hole, single outlet (fixed) combination tap assemblies (various chrome plated brass bodies), incorporating quarter turn ceramic disc headworks and a single lever operating members and a self-cancelling diverter to shower outlet. The spout outlet incorporates a flow straighter, and supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 WMSNK C CD | Crome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet |
Note - Both Products are the same, one is wall mount, one is deck mounted.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WB743-2* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WB743-4* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| JD-WS792* ** | Various | BSP 1/2” (F) Captive nut | 10 bar | 60 °C | Kind | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 36 107 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator | ||
| 36 115 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K007* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
| B008* | Various | ½" captive nut | 10 bar | 65 °C | WINSDRUM | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TS231** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator | |
| TS232** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
‘EPS50’ range of stainless-steel axial compensators with threaded end connections and ‘EPSF-10’ range of stainless-steel expansion joints with rotatable flanged end connections. Maximum working pressure: 16bar. Maximum operating temperature: 100°C.
102606 Mini shock arrestors with a stainless steel body. Maximum working pressure 15.0 bar. Maximum operating temperature 70°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ‘PPS/GF BFS (black)’ shrink back fittings for use with ‘Uponor Combi pipe’ (PEX/EVOH/PEX). Maximum operating pressures 12 bar & 6 bar, with maximum operating temperatures 20°C & 95°C respectively.
'Instantor’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Instantor’ stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of plastic pushfit fittings, for use with ALTOPOLY EVOH PEX pipe, manufactured to BS7291-3:2010 (15 to 22mm), PEX pipe manufactured to BS 7291-3 (28mm only) and ALTOPOLY PB pipe (white and grey) manufactured to BS7291-2:2010 (15 to 28mm). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of brass fittings inserts for use with copper pipes (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 16.0 bar @ 30°C and 10.0 bar @ 95°C.
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C.
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C.
Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.
Range of water meter manifolds with plastic bodies, for use with MDPE pipe to BS EN 12201 pipe (for the push-fit models). The inlets incorporate a spherical valve and a non-return valve (not suitable for back flow protection). Maximum operating pressure 12.5 bar. Maximum operating temperature 23°C
Range of flow measurement devices (DZR brass) bodies incorporating two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of stainless steel bodied mechanical pump shaft seals. Cold water use only.
Range of DZR brass metering stations supplied with red and blue test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
KLDG-WR Range of electromagnetic flow meters with carbon steel bodies, NBR inner liner and stainless-steel electrodes. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Automated Leak detection device with a plastic body and spherical valve. Maximum working pressure 8 bar. Maximum operating temperature 45˚C.
Range of threaded fittings with either brass or chrome plated brass bodies. Maximum working pressure 40 Bar Maximum operating temperature 85°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 26.569.000 | Chrome | 1/2" BSP (F) | Open Outlet bar | 65 °C | Grohe | faceplate | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| DS3007 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable | ||
| DS5010 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| S015* | Various | 1/2" BSP (F) | For open outlet use only bar | 85 °C | WINSDRUM | On back plate | No | Not applicable | Not Applicable | Not Applicable | |
| S016* | Various | 1/2" BSP (F) | For open outlet use only bar | 85 °C | WINSDRUM | On back plate | No | Not applicable | Not Applicable | Not Applicable | |
| S017* | Various | 1/2" BSP (F) | For open outlet use only bar | 85 °C | WINSDRUM | On back plate | No | Not applicable | Not Applicable | Not Applicable | |
| S018* | Various | 1/2" BSP (F) | For open outlet use only bar | 85 °C | WINSDRUM | On back plate | No | Not applicable | Not Applicable | Not Applicable | |
| S019* | Various | 1/2" BSP (M) | For open outlet use only bar | 85 °C | WINSDRUM | On body | No | Not applicable | Not Applicable | Not Applicable | |
| S020* | Various | 1/2" BSP (M) | For open outlet use only bar | 75 °C | WINSDRUM | On body | No | Not applicable | Not Applicable | Not Applicable | |
| S021* | Various | 1/2" BSP (M) | For open outlet use only bar | 85 °C | WINSDRUM | On body | No | Not applicable | Not Applicable | Not Applicable | |
| S022* | Various | 1/2" BSP (M) | For open outlet use only bar | 85 °C | WINSDRUM | On body | No | Not applicable | Not Applicable | Not Applicable |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of bib and hose union taps incorporating either brass or DZR brass (142HU prefix models only) bodies and non-rising spindle headworks. The FGK suffix models incorporate a ferrule guard and key (lockshield). The inlet and outlet of the 142HU (508107) and 142HU FGK (501117) models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperatures: 142HU (508107) and 142HU FGK (508117) models 65°C, all other models 90°C.
Range of wall mounted bib taps with bronze bodies, incorporating rising spindle headworks. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20302.G15.CP5R-8510 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8510 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8511 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20362.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet |
Wall Mounted Undefinable air gap see IRNs Incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.
A7255AA range of PEX lined shower hoses incorporating corrugated interlocking metal hoses with various finishes. All hoses incorporate EPDM washers. Maximum operating temperature 65°C.
Rinnai range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
Range of automatic air venting valves with a brass body and a plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TSSL1 | Chrome | 15mm Compression | 5 bar | 60 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, Riser Rail, | |
| AQSL1 | Chrome | 15mm Compression | 5 bar | 60 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, Riser Rail, |
Wall Mounted thermostatically controlled shower valve supplied with shower hand-set, hose with riser rail and overhead shower in chrome finish. Incorporating a 1/4 turn ceramic disc headwork & flow regulator. Maximum temperature 65°C. Maximum Pressure 5 bar.
Range of wall mounted concealed thermostatic blending valves with brass bodies (various finishes), incorporating single sequential headworks with single lever operating members. The inlet couplings incorporate plastic flow regulators & metal strainers. The outlets incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic shower valves, (chromium plated brass), incorporating a thermostatic cartridge which controls both flow and temperature. All models have a single lever operating member controlling the flow and a cross-top operating member controlling the temperature, includes a manual override button on the temperature control. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Vulcain range of wafer, lugged or flanged butterfly valves with blue epoxy coated ductile iron bodies and discs, with lever type or handwheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Combined temperature and pressure relief valves pre-set at 7.0 or 10.0 bar (See models) with a DZR brass body. The valves incorporate lever easing gear. Maximum working pressure: See models. Maximum operating temperature 85.0°C
Range of combined pre-set temperature and pressure relief valves incorporating Bronze body, DZR brass seat and plunger, EPDM ‘O’-rings, PTFE seal and silicone diaphragm. The valves incorporate a manually operated lever easing gear. The valves are factory pre-set between 0.7 bar and 12.5 bar. Maximum operating temperature 90°C. Maximum working pressure between 0.7 bar and 12.5 bar. Maximum operating temperature 90.0°C
Range of BOSS 958 combined pre-set temperature and pressure relief valves incorporating Bronze body, DZR brass seat and plunger, EPDM ‘O’-rings, PTFE seal and silicone diaphragm. The valves incorporate a manually operated lever easing gear. The valves are factory pre-set between 0.7 bar and 12.5 bar. Maximum operating temperature 90°C. Maximum working pressure between 0.7 bar and 12.5 bar. Maximum operating temperature 90.0°C
Combined temperature and pressure relief valve incorporating DZR bronze body, and a rubber silicone seat washer. Compression fittings for use with copper to BS EN 1057. Maximum working pressure 7.0 Bar Maximum operating temperature 95.0°C
Range of piston type float operated valves with plastic bodies. Maximum operating pressure: 14 bar. Maximum operating temperature: 23°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 7.0bar . Maximum working pressure: 25.0 bar or 30.0 bar depending on model. Maximum operating temperature 80°C.
Range of pilot valves with a plastic housing incorporating a solenoid valve. The inlet incorporates a combined plastic washer and stainless-steel strainer. Maximum operating pressure 10 bar. Maximum operating temperature 50°C.
Spherical valves with chrome or nickel plated brass body, chrome plated ball, PTFE seats and FKM ‘O’-ring. The products are available with lever or butterfly operating member. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Lever operated spherical valve with brass body (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with nickel plated brass bodies and chromium plated brass balls. The valves are either screwdriver or lever operated(see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (HC-A61055-22 model) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
OS & Y Range of gate valves with blue, black or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down stop valves with brass bodies, EPDM gaskets and PTFE washers. For use with copper pipe to EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 99°C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of manually operated balancing valves with a DZR brass body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of electrolytic water conditioners, with a brass body and zinc alloy anodes. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. 403342 & 403359 Electrolytic models have a maximum operating temperature of 40°C. 403328 & 403335 Magnetic models are cold water use only.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BAJ0002'. Factory applied, blue coloured epoxy coating. Pre-heat substrate for 30 minutes@200°C and apply in accordance with manufacturer's Product Instructions 'Version-01 202426 September'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Plustek PA7001G7BK11'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'PAG11-YT60SF'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'RAMSTER PF100NT'. White coloured (opaque), injection moulded PBT material. For use with water up to 85°C.
'Qingfa PE100 Black Pipe Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'P193'. Extruded, multi-layered pipe comprising of an off-white (translucent), PEX-Xc inner layer, aluminium middle layer and white coloured (opaque), PE-Xb outer layer. For use with water up to 85°C.
'Radius Systems SC100 (PE100) Dark Blue Pressure Pipe'. Extruded, dual layered pipe comprising of a black coloured PE100 inner layer and a blue coloured PE100 outer layer. For use with water up to 23°C.
'RAK Universal Plastic Industries L.L.C. HDPE PE100 Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'ELTEX® SUPERSTRESS TUB121N9000'. Black coloured, compression moulded HDPE material. For use with water up to 23°C.
'ELTEX® SUPERSTRESS TUB124N6000'. Blue coloured, compression moulded HDPE material. For use with water up to 23°C.
'ECOTRAN E1040W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E1040W(#) NC'. Natural (appears brown) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'RAMOFIN PPH301G6NT'. White/beige coloured, injection moulded polypropylene material. For use with water up to 85°C.
'F1100'. White coloured (opaque), PTFE material manufactured by extrusion and machining. For use with water up to 85°C.
'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Anchor Pro Plus'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 2025 - 12 - 09. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ResiFIX Max Performance Epoxy'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's European Technical Assessment ETA-25/1132 of 2025/11/19. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP10/7/7 BLK gaskets & 'O' rings'. Injection moulded, black coloured EPDM gaskets & 'O' rings. Shore hardness 70. The gaskets have an in-radius size of 0.75mm. The ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'EP2504 (NSF)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'E40D'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'Silicone RS7007 Inner Hose'. Colourless (translucent), extruded silicone hose. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'7741'. Red coloured, compression moulded, silicone rubber material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Fernox LS-X'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet dated 10-05-2021. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘202968 Tradesave Pipe Sealing Cord TSTPSC160’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.0’, dated 26/11/2025 and this material is only approved for these conditions. For use with water up to 85°C.
'202973 Tradesave Thread Lock TSTTS050'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1.0', issue date '01/12/2025'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Loxeal 18-11'. White coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions 'PLUMEFF', dated '2024/09/17'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ABS011 ABS Pipe Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 26112025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F9920-** | Various | 1/2" Captive nut | 10 bar | 60 °C | LAN BIAO | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
**Representing different surface color treatments： No Suffix = Chrome, H: Black DYB: Matte White BZ: Pearl White HGTS: Red Antique Bronze HTL: Yellow Bronze Brushed Q: Bronze QTSL: Bronze Brushed Bright QTS: Bronze Brushed Matte STS: Acid Copper Brushed SDMGJ: Water-Plated Rose Gold N: Nickel Brushed Bright NP: Nickel Brushed TJ: Titanium Gold TJLS: Titanium Gold Brushed G: Zirconium gold GJS: Zirconium Gold Brushed GJSY: Zirconium Gold Brushed Matte PGJFY: Zirconium Gold Brushed Bright PLSJ: Brushed Gold LSJY: Brushed Gold Matte MGJ: Rose Gold MGJL: Rose Gold Brushed DMGJ: Light Rose Gold Brushed HTS: Red Copper Brushed QHP: Gunmetal Gray LSQH: Gunmetal Gray Brushed LHMGJ: Brushed Yellow Rose Gold
'Hydro/EC100/EC Capsule Retaining Dowel'. Grey coloured, extruded PVC-U dowel. For use with water up to 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 24015** | Various | 1/2" BSP (F) | 8 bar | 85 °C | NLB | On body | No | Ceramic cartridge | C-plate | Aerator | Interconnecting Hoses, |
| 25001** | Various | 1/2" BSP (F) | 8 bar | 85 °C | NLB | On body | No | Ceramic cartridge | C-plate | Aerator | Interconnecting Hoses, |
** represent different finishes No suffix: Chrome plated H: Black, N: Nickel brushed, GJS: Zirconium gold brushed, G: Zirconium gold, QTSL: Brushed bronze bright, QTS: Brushed bronze matte, TJ: Titanium gold, TJLS: Titanium gold brushed, MGJ: Rose gold, MGJL: Rose gold brushed, HGT: Red bronze, HTL: Yellow bronze brushed, HTS: Red bronze brushed, PVDQH: Gun grey, HQ: Gun grey brushed, Q: Bronze, DYB: Matte white, STS: Acid copper brushed, BZ: Spray pearl white, DMGJ: Light rose gold brushed.
Deck mounted, two-hole, single outlet (fixed) combination tap assemby (brass body, various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic aerator. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (swivel) combination tap assembly (brass bodies – various finishes), incorporating non-rising spindle headworks with cross top operating members and manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener (optional aerator is also supplied) and the product is supplied with a shower hose, shower handset and metal back nuts. Maximum working pressure 10.0Bar Maximum operating temperature 60°C.
Range of combined bath fillers and overflow waste assemblies with plastic bodies (various finishes). The outlet incorporates a plastic aerator. The products are supplied with a cable operated pop-up waste. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 090 8xx | Various | G 1/2" | 10 bar | 65 °C | AXOR | on the nut | Yes | Not applicable | Not Applicable | Not Applicable | Shower Hose, |
Where 8xx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| DH2118 | chrome | ½" conical nut | Open outlet bar | 65 °C | DELMEI, WRAS, Manufacture Date（YYYY） | On connector | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| WS3** | Various | BSP 1/2" (F) | 10 bar | 65 °C | Kind | sleeve | No | Ceramic cartridge | Not Applicable | Not Applicable |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AHT2 | BSP 1/2" (F) | 10 bar | 65 °C | Kind | Body | No | 1/2 Turn ceramic disc | Not Applicable | Not Applicable |
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chromium plated), incorporating an isolation valve. Compression connections to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies with DZR brass or stainless steel bodies, incorporating two spring loaded, resilient trim in-line check valve cartridges Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 35A4 | 35mm | 25 bar | 65 °C | Hassem logo | Body | No | Ceramic cartridge | ||||
| 40A | 40mm | 25 bar | 65 °C | Hassem logo | Body | No | Ceramic cartridge | ||||
| HSP-024 | 18mm | 25 bar | 65 °C | HS, Production date(YYYYMMDD) | Body | No | Push button detent | ||||
| QB-001L | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QB-001R | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSD-A001L | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSD-A001R | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSE-N003L | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSE-N003R | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QB-318 | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QD-445 | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QD-446 | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D40P-19D | 40mm | 16 bar | 85 °C | MS, D40P-19D | Body | No | |||||
| D40P-19D2 | 40mm | 16 bar | 85 °C | MS, D40P-19D2 | Body | No |
Range of ceramic cartridge headworks for insertion into specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TPASHMONO3 | Chromed | 1/2" Captive nut | 10 bar | 60 °C | Lecico bathrooms | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| TPSOUMONO3 | Chromed | 1/2" Captive nut | 10 bar | 60 °C | Lecico bathrooms | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator |
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members.The spout otlet incorporates a plastic aerator. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CNN EFSNK FL6 C | Chrome | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | Ceramic cartridge | C-plate | Aerator |
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Model 24.272.xx1 is supplied with a lever type pop-up waste set – not verified by test.. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with a click type waste (not verified by test). Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| K BF C | Chrome 6 | 3/4" BSP (M) | 5 bar | 65 °C | Bristan | Indice | No | 1/4 Turn ceramic disc | Metal Backnuts | Open Outlet | |
| RP3 K BF C | Chrome 3 | 3/4" BSP (M) | 5 bar | 65 °C | Bristan | Indice | No | 1/4 Turn ceramic disc | Metal Backnuts | Open Outlet |
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a ceramic disk diverter with dome type operating member controlling the flow between the outlets. The spout outlet incorporates a plastic aerator. Maximum working pressure: 10.0 Bar Maximum operating temperature: 60°c
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks and lever type operating members. The spout outlet incorporates a plastic aerator and supplied with metal back nuts. Maximum operating pressure 5.5 bar. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 BRDSM C CD | Chrome | 1/2" BSP (M) | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disc | Metal Backnuts | Open Outlet | |
| VAL2 BRDSM C 6 CD | Chrome | 1/2" BSP (M) | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disc | Metal Backnuts | Open Outlet |
VAL2 BRDSM C 6 CD - has a 6 inch lever
‘HydroDOS’ chlorine dioxide dosing system with PVC-u pipework, water meter, strainer, isolation valves and a drain cock with hose spigot. Maximum working pressure 6.0 bar. Cold water use only.
Expansion vessel with a carbon steel body, polypropylene cover and a butyl membrane. Maximum working pressure: 10 Bar. Maximum operating temperature: 99°C.
Expansion vessels incorporating a stainless-steel body and SEFA membrane. Maximum working pressure: 10 bar, except A2C2R27 WR000 (DP 24/16X) 1” BSPP (M) which is 16 bar. Maximum operating temperature 85˚C.
Range of expansion vessels having stainless steel bodies. Maximum operating pressure 7 - 25 bar. Maximum operating temperature 85°C
Range of ZL brass compression fittings. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Plastic bodied inline push fit reducer for use with Shin Won Tube Co., Ltd. SWPE™ (LLDPE) tube, (not covered by the scope of this approval). Maximum working pressure 10.0 bar. Cold water use only.
‘SLD’ range of copper press fittings with ‘V’ and ‘M’ press profiles and EPDM ‘O’ rings. Fittings to be used with copper pipe manufactured to EN1057. Maximum working pressure: 16 Bar. Maximum operating temperature: 85°C.
Stainless steel M-profile press-fit fittings (316L) and pipes (316L - EN 10312 and 304 – EN 10312). Maximum operating pressure 16 bar. Maximum operating temperature 100°C.
Flowflex Range of press-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with SS316L pipes. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of domestic stainless steel indirect unvented hot water storage cylinders, incorporating a stainless-steel coil for connection to external heating resource. The secondary circuit is factory fitted with a temperature and pressure relief valve (7.0 Bar @90°C) and an immersion heater. Primary working pressure: 3 bar; secondary working pressure: 5.5 bar. Maximum operating temperature 90 °C.
Range of water meters with blue epoxy coated brass or iron bodies (see models) and a plastic strainer on the inlet. Maximum working pressure 16.0 Bar or10.0 Bar(see models). Maximum operating temperature 50°C.
Range of ultrasonic water meters with a blue epoxy coated ductile iron body and EPDM ‘O’ rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 50°C.
Range of water meters with plastic bodies and plastic working chamber and EPDM ‘O’ rings. The inlets incorporate a plastic filter. Maximum working pressure 16.0 Bar. Maximum operating temperature 50°C.
Range of water meters with plastic bodies and plastic working chamber and EPDM ‘O’ rings. The inlets incorporate a plastic filter. Maximum working pressure 16.0 Bar. Maximum operating temperature 50°C.
Water meter carrier with DZR brass body. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Individual threaded fitting with SUS316L body. Maximum working pressure: 6 bar Maximum operating temperature 90°C.
Range of metering stations with DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel pressure sensors. Maximum working pressures: B83.a-b-C5-3-f-g-h-i-j-k-l-m-n-o (Thread G1): 10.0 bar. B83.a-b-cd-e-f-g-h-i-j-k-l-m-n-o with METEC - metallic measuring cell: 25.0 bar, B83.a-b-cd-e-f-g-h-i-j-k-l-m-n-o with Piezoresistive - metallic measuring cell: 40.0 bar. Maximum operating temperature 100°C
Range of flow sensors with brass bodies (various grades - see model). Maximum working pressure 16.0 bar. Maximum operating temperature 90°C.
Range of electric water pumps, with stainless steel bodies, shaft and either stainless steel or plastic impellors. Maximum working pressure 8.5 Bar. Maximum operating temperature: See models.
Range of self-priming electric booster pumps with plastic bodies incorporating plastic impellers with variable speed settings, and a non-return return valve (not suitable for backflow protection). Maximum working pressure 4.5 Bar Maximum operating temperature 50.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| S34011 | Chrome plated | 1/2" BSP (M) | For open outlet use only bar | 75 °C | DOMOO | Body | No | ||||
| S06041 | Chrome plated | 1/2" BSP (M) | For open outlet use only bar | 75 °C | DOMOO | Body | No | ||||
| S185015(88500103) | Chrome plated | 1/2" BSP (M) | For open outlet use only bar | 65 °C | DOMOO | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 37902W-MB5 | BLACK | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Handset, |
| 37902W-MG5 | GREEN | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Handset, |
| 37902W-GB5 | BLUE | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Handset, |
| 37902W-CS5 | GREY | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Handset, |
| 37902W-BP5 | PINK | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Handset, |
| 37903W-MB5 | BLACK | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Fixed Head, |
| 37903W-MG5 | GREEN | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Fixed Head, |
| 37903W-GB5 | BLUE | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Fixed Head, |
| 37903W-CS5 | GREY | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Fixed Head, |
| 37903W-BP5 | PINK | ½” BSP | OPEN OUTLET bar | 60°C °C | MIRA SHOWERS | SPRAY PLATE | No | Not applicable | Not Applicable | Open Outlet | Fixed Head, |
Range of drain cock elbows incorporating a DZR brass body, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures:16.0 bar. Maximum operating temperature 85°C.
Flexible safety hose assembly with PVC, composite inner hose and corrugated outer cover incorporating EPDM gaskets. The inlet of the hose incorporates a plastic strainer. The hose is fitted with an integral device which is intended to stop the flow of water (please note that this function has not been verified by test). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of ‘THINK-A-FLEX’, EPDM lined, stainless steel braided flexible hose assemblies incorporating various end connections Maximum working pressure: 10 BAR Maximum operating temperature: 65°C
Range of stainless steel braided silicone lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 Bar. Maximum operating temperature 70°C.
Range of gas fired, unvented hot water storage heaters. The DHW circuit consists of a temperature and pressure relief valve (set at 7.0Bar). Maximum working pressure: 6.5 Bar. Maximum operating temperature: 85°C.
Range of single or double tank water heaters, incorporating enamel coated carbon steel tank. The secondary circuit is factory fitted with a temperature and pressure relief valve (10.0 Bar). Maximum working pressure 8 bar. Maximum operating temperature 75 °C.
Range of 2, 3 and 4 port manifold assemblies with either DRZ brass (3834.1, 3834.34, 3835.34, 3835.1, 3837.37 & 3837.1) or brushed chrome plated brass bodies incorporating screw down isolation valves with dome type operating members at each of the outlets. Maximum working pressure: 16 Bar. Maximum operating temperature: 95°C.
Range of wall mounted manually operated, concealed shower valves (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members and a manual diverter to shower outlets with single lever operating members. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Range of wall mounted shower valves with brass bodies with various finishes (see models). The products incorporate a ceramic cartridge headwork with a single lever operating member that controls both the flow and temperature. Maximum working pressure; 10 Bar Maximum operating temperature; 60°c
Range of wall mounted thermostatic shower valves with (brass bodies – various finishes), incorporating a 2-way ceramic disc diverter controlling the flow to either the shower handset or an overhead shower using a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product is supplied with an overhead shower, riser rail, shower hose and handset. The inlet to the overhead shower incorporates a plastic strainer. The product incorporates approved single check valves at the inlet, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure; 10 Bar Maximum operating temperature; 60°c
Range of wall mounted thermostatic shower valves (brass bodies – various finishes) incorporating either a 2-way ceramic disc diverter (model TVT11000200061) controlling the flow to either an overhead shower or bath filler with dome operating members or a quarter turn ceramic disc headwork to shower handset. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature is 60°C.
Range of concealed, wall mounted thermostatic shower valves with brass bodies (chromium plated trim sets). The products incorporate a one or two-way function and a thermostatic cartridge controlling the temperature with lever type operating members. All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of flanged butterfly valves with either lever or hand wheel operation and a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs with EPDM seats and a lever operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of eccentric flanged type butterfly valves with ductile iron bodies and disc (blue epoxy coated) and EPDM seats. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of wafer, lugged and flanged butterfly valves with blue epoxy coated ductile iron bodies, nickel plated ductile iron discs, EPDM seat and NBR ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
2101 Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and PTFE seats. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| D22P-1D | 22mm | 16 bar | 85 °C | MS, D22-1D | Body | No | |||||
| D26P-3 | 26mm | 16 bar | 85 °C | MS, D26P-3 | Body | No | |||||
| D26P-3B | 26mm | 16 bar | 85 °C | MS, D26P-3B | Body | No | |||||
| D26P-3FY | 26mm | 16 bar | 85 °C | MS, D26P-3FY | Body | No | |||||
| D28P-3B2 | 28mm | 16 bar | 85 °C | MS, D28P-3B2 | Body | No | |||||
| D28P-3B3 | 28mm | 16 bar | 85 °C | MS, D28P-3B3 | Body | No | |||||
| D28P-3D2 | 28mm | 16 bar | 85 °C | MS, D28P-3D2 | Body | No | |||||
| D28P-6 | 28mm | 16 bar | 85 °C | MS, D28P-6 | Body | No | |||||
| D40P-19A | 40mm | 16 bar | 85 °C | MS, D40P-19A | Body | No | |||||
| D40P-19B2 | 40mm | 16 bar | 85 °C | MS, D40P-19B2 | Body | No | |||||
| D56P-1 | 56mm | 16 bar | 85 °C | MS, D56P-1 | Body | No | |||||
| D56P-2 | 56mm | 16 bar | 85 °C | MS, D56P-2 | Body | No | |||||
| D56P-3 | 56mm | 16 bar | 85 °C | MS, D56P-3 | Body | No |
2-way, ceramic disc, rotary diverter valve which controls and diverts the flow, for insertion into specifically dimensioned bodies. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Fire hydrant with an epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C. Above ground use only.
Range of swing gate non-return valves with epoxy coated ductile iron bodies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of swing gate non return valves with ductile iron bodies (blue epoxy coated). Maximum working pressure - 16.0 bar. Maximum operating temperature - 85°C.
Range of normally open or closed solenoid valves with brass bodies. Maximum working pressures: SCE210C034BW, SCE210C035BW: AC only 9.0 bar. SCE210C094BW, SCE210D095BW: AC 9.0 bar, DC 3.0 bar. Maximum operating temperature: 85°C
Range of 3-way brass spherical valves incorporating a chrome plated brass ball and PTFE seats. Maximum working pressure: See models Maximum operating temperature 60.0°C
Range of in line spherical valves incorporating chrome plated brass bodies, chrome plated brass ball. Model 825212 & 803815 incorporate a single lever operating member, models 825015 and 8250152 have no operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of in-line lever operated spherical (SB2415) or screwdriver operated servicing (SB1915 & SB1922) valves with chromium plated brass bodies and balls, EPDM seals and ‘SharkBite’ push fit end connections. For use with PB pipe manufactured to EN7291-2:2010, PEX Pipe Manufactured to EN 7291-3:2010 and copper pipe manufactured to EN1057. Maximum working pressure: 12.5 Bar at 20°C (PEX & PB Pipe) 6.0 Bar at 95°C (PEX & PB Pipe) 20.0 Bar at 20°C (Copper Pipe) 16.0 Bar at 95°C (Copper Pipe)
Range of spherical valves incorporating brass bodies and balls (nickel plated), EPDM rubber ‘O’-rings, PTFE seats and red or blue coloured lever type operating members. Maximum working pressure; 10 Bar Maximum operating temperature; 65°c
Range of spherical valves incorporating brass bodies and ball. Maximum working pressure see models. Maximum operating temperature 100°C.
Range of press fit spherical valves with brass bodies, stainless steel balls and PTFE seats. The valve are available with lever, extended lever, lockshield lever and butterfly handle operating members. For use with copper pipe (manufactured to EN1057) and stainless-steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ or ‘V’ profile (model dependent). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating cast iron bodies (blue epoxy coated), EPDM rubber coated wedges and non-rising spindles with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure –16.0 bar. Maximum operating temperature - 85°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via a non-rising spindle headwork with hand wheel operating member or electronic remote-control system (see model). Maximum working pressure 16.0 bar. Cold water use only.
Screw down stop valve (chromium plated brass) incorporating a dome (triangular) type operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 100.0°C
Range of inlet control groups with DZR brass bodies consisting of an in-line, adjustable pressure reducing valve (adjustable in the range of 1.0 bar to 6.0 bar, pre-set at 3.0 bar), a pressure relief valve (6.0 bar) and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
'ApiAlu PP-RCT Class 2 Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-RCT inner layer, aluminium middle layer and black coloured PE 100 outer layer. For use with water up to 85°C.
'TIMCO VESF 300/VESF 410'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 01.12.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 24016** | Various | 1/2" BSP (F) | 8 bar | 85 °C | NLB | On body | No | Ceramic cartridge | C-plate | Aerator | Interconnecting Hoses, |
** represent different finishes No suffix: Chrome plated H: Black, N: Nickel brushed, GJS: Zirconium gold brushed, G: Zirconium gold, QTSL: Brushed bronze bright, QTS: Brushed bronze matte, TJ: Titanium gold, TJLS: Titanium gold brushed, MGJ: Rose gold, MGJL: Rose gold brushed, HGT: Red bronze, HTL: Yellow bronze brushed, HTS: Red bronze brushed, PVDQH: Gun grey, HQ: Gun grey brushed, Q: Bronze, DYB: Matte white, STS: Acid copper brushed, BZ: Spray pearl white, DMGJ: Light rose gold brushed.
Range of deck mounted single hole, single outlet, fixed electronically controlled tap assemblies with (brass bodies – various finishes), incorporating a solenoid valve controlling the flow which is activated via an infrared sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, single outlet, fixed electronically controlled tap assemblies with (brass bodies - chrome plated), incorporating a solenoid valve controlling the flow which is activated via an infrared sensor. The spout outlet incorporates a plastic aerator, and the product is supplied with a metal backnut. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated stainless brass body). Flow is controlled by a solenoid valve and is activated via an infrared sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Bottom entry or side entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use
Range of WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush Syphon of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055 (2018) WC Cistern incorporating a side or bottom entry float operated inlet valve discharging via a Type AG air gap and a dual flush Syphon of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a lever. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve and a dual or single flush pneumatic or dual flush cable operated drop valve capable of full flush volumes of up to 6 litres with a reduced flush of up to 4 litres. Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap with a Pneumatic or Cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. Maximum working pressure 10.0 bar. Cold water use only.
Range of multi-layer shower hoses with a PVC inner hose, supplied with EPDM ‘O’-rings. Maximum operating temperature 60.0°C Open outlet use only.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body, compression models are nickel plated. A drain port is provided between the cartridges. Compression models are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 Bar Maximum operating temperature: 85.0°C (D220W models) or 60.0°C (D220CW models)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5001JC45-1 | Chrome | 1/2 BSP(F) | 10 bar | 85 °C | HUANRI | BODY | No | Ceramic cartridge | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| XB-CT48S001 | 49mm | 16 bar | 85 °C | Tzxinbai, XB-CT48S001 | Body | No | |||||
| XB-CT48S002 | 49mm | 16 bar | 85 °C | Tzxinbai, XB-CT48S002 | Body | No | |||||
| XB-CT48S003 | 49mm | 16 bar | 85 °C | Tzxinbai, XB-CT48S003 | Body | No | |||||
| XB-CT07S | 34mm | 16 bar | 85 °C | Tzxinbai, XB-CT07S | Body | No | |||||
| XB-CT27S | 27mm | 16 bar | 85 °C | Tzxinbai, XB-CT27S | Body | No | |||||
| XB-CT28S | 28mm | 16 bar | 85 °C | Tzxinbai, XB-CT28S | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WK313P* ** | Various | 1/2" Captive nut | 10 bar | 60 °C | Kind | Operating member | No | Ceramic cartridge | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| JD-WK323P* ** | Various | 1/2" Captive nut | 10 bar | 60 °C | Kind | Operating member | No | Ceramic cartridge | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| JD-WK2003* ** | Various | 1/2" Captive nut | 10 bar | 60 °C | Kind | Operating member | No | Ceramic cartridge | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| JD-WK2003-3* ** | Various | 1/2" Captive nut | 10 bar | 60 °C | Kind | Operating member | No | Ceramic cartridge | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| JD-WK743* ** | Various | 1/2" Captive nut | 10 bar | 60 °C | Kind | Operating member | No | Ceramic cartridge | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
1. The first * denotes different handles and can be replaced with A, B, C and D. 2. The second ** represents different types of finishes as follows. C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: white CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 4001JC45-1 | Chrome | 1/2BSP(F) | 10 bar | 85 °C | HUANRI | BODY | No | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 4001JC45-3 | Chrome | 1/2BSP(F) | 10 bar | 85 °C | HUANRI | BODY | No | Ceramic cartridge | C-plate | Aerator |
The model 4001JC45-1 and 4001JC45-3 taps are same, except that 4001JC45-1 comes with a click-type waste fitting included during sale, while the 4001JC45-3 model does not.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T5002 | Chrome plating | ½” BSF (F) Captive nut | 5 bar | 65 °C | SONAS | on operating member | No | Ceramic cartridge | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| USH0229 | chrome plated | ½” BSF (F) Captive nut | 5 bar | 65 °C | SONAS | on operating member | No | Ceramic cartridge | C-plate | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 521502 - KANO TP HP CHR | Chrome (CHR) | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525028 - KANO TP HP ANT / CHR | ANT / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525030 - KANO TP HP SGW / CHR | SGW / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525033 - KANO TP HP CAF / CHR | CAF / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526175 - KANO TP HP BLA / CHR | BLA / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526667 - KANO TP HP BL | BL | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526950 - KANO TP HP VGR / CHR | VGR / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526951 - KANO TP HP SOW / CHR | SOW / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator |
CHR - Chrome ANT - anthracite SGW - silgranite white CAF - coffee BLA - black BL - black matt VGR - volcano grey SOW - soft white
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ROC2MB | MATT BLACK | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2RC | REGENCY COPPER | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2AB | ARTISAN BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2BN | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BV | MATT BLACK | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073RC | REGENCY COPPER | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073AB | ARTISAN BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BS | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITCP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITPB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITBS | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2BN | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ZO3BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ZO2BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1001JC45 | Chrome | ½” BSP (M) x ¾” BSP (M) offset union | 10 bar | 85 °C | HUANRI | Rear of body | No | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M33275 X XXX | VARIOUS | 3/4” BSP male inlet. | 5 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Filling valve with a DZR brass body comprising of: Two check valve cartridges on the inlet, verified by test (suitable for backflow protection against Fluid Category 3), a pressure reducing valve preset at 1.4 bar, a sprung loaded self-closing valve and a single check valve cartridge on the outlet, verified by test (suitable for backflow protection against Fluid Category 2). There is a drain port below the self-closing valve chamber. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum inlet supply pressure 10.0 bar. Maximum operating temperature 100°C.
‘EPS’, ‘EPT & ‘EPL’ ranges of PPSU press fittings (TH press profile) with EPDM ‘O’-rings for use with ‘EFIELD EA’ PE-Xb/AL/PE-Xb multilayer pipes. Maximum working pressure: 10 bar. Maximum operating temperature: 95°C
Range of press fittings (brass bodies) with stainless steel press (‘TH’ profile) collars and EPDM o-rings for use with ‘EA’ PE-Xb/AL/PE-Xb’ multilayer pipe (for press fitting connections) or copper pipe manufactured to EN1057 (compression connections). Maximum working pressure: 10 bar. Maximum operating temperature: 95 °C.
Range of copper or chrome plated copper (CP suffix models) press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressures: 12mm to 54mm: 16.0 bar, 66.7mm to 108mm: 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘V’ profile. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of ultrasonic water meters with brass/plastic bodies. The Iskrasonic 1000 MWU5 range inlets incorporate a plastic strainer and brass spherical ball valve with PTFE seats. The Iskrasonic 1000 IWU 100 range inlets incorporate a plastic strainer Maximum working pressure 16.0 bar. Maximum operating temperature 50⁰C.
Range of EPDM expansion joints. Maximum working pressures: YXY6: 6.0 bar, YXY10: 10.0 bar, YXY16: 16.0 bar, YXY25: 25.0 bar. Maximum operating temperature 85°C.
Screw down, angled isolation valve with a dome type operating member, incorporating a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
FVC & FVS Ranges of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| WJ V/HANDLE CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 931 IX | STAINLESS STEEL | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 23931 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 27931 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 28931 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 21931 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 649510 CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 639510 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 679510 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 689510 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 619510 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH G | POLISHED GOLD | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH NK | NICKEL | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 15930 CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 23930 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 27930 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 28930 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 21930 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No |
Chrome Plated shower handsets. For open outlet use only. Maximum temperature 75 °C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 21-005-481 | Chrome plated | ½” BSP (M) | Open outlet use bar | 65℃ °C | AKW | on handset body. | No | Handset, | |||
| 21-005-482 | White colour | ½” BSP (M) | Open outlet use bar | 65℃ °C | AKW | on handset body. | No | Handset, |
Range of flanged Y pattern strainers with black epoxy coated ductile iron bodies and stainless-steel mesh. Maximum working pressure 16.0 bar for FM276W models and 25.0 bar for FM278W models. Maximum operating temperature 85°C.
Range of flanged Y pattern strainers with black epoxy coated ductile iron bodies and stainless-steel mesh. Maximum working pressure 16.0 bar for Fig 816W models and 25.0 bar for Fig825W models. Maximum operating temperature 85°C.
Draining tap with a brass body and a rising spindle headwork. Pressfit jointing is achieved via a crimping tool using a ‘V’ profile and is for use with copper pipes (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. The 4GANc32 and 4GANc41 models incorporate an isolation valve. Max working pressure:10bar Max working temperature:85°c
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1011JC45 | Chrome | ½” BSP (M) x ¾” BSP (M) offset union | 10 bar | 85 °C | HUANRI | Rear of body | No | Open Outlet |
T-type thermostatic blending valve with a brushed chrome, DZR brass body. Temperature is pre-set under a fixed cap. The inlets incorporate stainless steel strainers and single check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F1100* | chrome or matte black | 3/4” BSP(F) | 5 bar | 85 °C | KY-LIN | on body | No | Ceramic cartridge |
Where * denotes the finish color, and can be replaced with the following: CHR = Chrome BLK = Matte Black The inlets incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SD-ZJXXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD124-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD205-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD127-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD170-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD190-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD246-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD191-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD109-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD207-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD101-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD116-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD117-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD125-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD128-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD156-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD168-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD209-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD210-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD212-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD213-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD220-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD222-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD236-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD238-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD240-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc |
XXXX represent five series shower valves and can be replaced to 2500, 2501, 2503, 2504, 2702.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 81971 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | ebb+flo | in the middle of thermostatic valve | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 57406 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | ebb+flo | in the middle of thermostatic valve | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
BV266 Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of lugged, wafer or double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless steel or blue epoxy coated ductile iron discs. The products can be supplied with a gear box and handheel operating member (all models) or a lever operating members (all models except TB-RF). Maximum working pressure 10.0 bar, 16.0 bar or 25.0 bar (see model). Maximum operating temperature 85°C.
VF900 Range of wafer butterfly valves with blue, black or red epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats, incorporating hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
Range of eccentric flanged type butterfly valves with ductile iron bodies and disc (blue epoxy coated) and EPDM seats. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of butterfly valves with blue epoxy coated, ductile iron bodies and handwheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of wafer non-return valves with stainless steel (SUS304 or 316) or galvanized carbon steel (A105) bodies, stainless steel discs (CF8 or CF8M) and either EPDM or FKM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of wafer non-return valves with blue epoxy coated ductile iron bodies, nickel plated or blue epoxy coated ductile iron or stainless steel discs and EPDM seals. Maximum working pressure 10.0 bar or 16.0 bar. Maximum operating temperature 85°C.
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pilot operated pressure reducing valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and O-rings. The products are supplied with auxiliary fittings: spherical valves, pressure gauges, a pilot valve, a needle valve and stainless steel tubes. The DN400 model also includes a Y-pattern strainer. Maximum inlet supply pressure 16.0 bar. The outlet pressure is adjustable between 0.7~16.0 bar. Maximum operating temperature 65°C.
Range of pilot operated pressure reducing valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and O-rings. The products are supplied with auxiliary fittings: spherical valves (bronze or stainless steel), pressure gauges, a pilot valve, a needle valve and stainless steel or copper tubes. Maximum inlet supply pressure 16.0 bar. The outlet pressure is adjustable between 0.67~16.0 bar. Maximum operating temperature 85°C.
Solenoid valve with a nickel plated brass body, incorporating an EPDM diaphram and sealing rings. The product incorporates a stainless-steel strainer in the inlet. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Screwdriver operated angled spherical valve with a brass body and ball, PTFE seats and EPDM ‘O’-rings. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Motorised spherical valve incorporating nickel plated brass body, chrome plated brass ball and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with a nickel plated brass body, chromium plated brass ball and PTFE seats. Compression ends are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Spherical ball valve (lever operated) with brass body, NBR O-rings and incorporates single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection is for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges, incorporating a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated ductile iron gate valves with an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of DZR brass combination valves consisting of an in-line adjustable pressure reducing valve (2.1 - 16.0 bar for ILG22-2 model and 1.4 - 6.0 bar for all other models), a pressure relief valve (set @ 6.0 bar) and EPDM gaskets and ‘O’-rings. The product incorporates a stainless-steel mesh and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 90°C.
Range of double regulating valves available with bronze bodies, incorporating a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'KOCETAL K100 GMP'. White coloured, injection moulded acetal material. For use with water up to 85°C.
'Super Poxy 505TL'. Factory applied, grey coloured, two-component Epoxy coating. Mix Parts A & B in a 100:20 weight ratio and apply as per manufacturer's TDS dated '2026.01.14'. Cure for 24 hours@20°C. For use with water up to 23°C.
'Nitomortar TC2000'. Factory applied, two-component, grey coloured (once mixed and applied) epoxy resin sealing compound. The material is supplied in pre-weighed quantities (60% base, 40% hardener), to be applied in accordance with manufacturer's instructions 'FO SA/NITOMORTAR TC2000/0110/19'. Cure for 7 days@25°C and 55% humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DUAYEN ANTIBLAST GEÇIRIMSIZ SPREY BOYA KAPLAMA'. Factory applied, two-component, black coloured (once mixed and applied), Polyurea coating. Mix parts A & B in a 1:1 volume ratio and apply as per manufacturer's TDS 'Rev01', date of issue '22.04.2024'. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NP TANK 500 PW'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a 3:1 volume ration and apply two coats as per manufacturer's TDS '0724'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate to 40°C and then spray apply as per manufacturer's instructions issued ‘March 2017, V4.1’. Cure for 20 minutes@180°C. For use with water up to 85°C.
‘Intergard 269’ primer for use with ‘Interline 975’ coating. Site applied, off-white coloured (once mixed and applied) epoxy coating system comprising of a two-part primer and two-part topcoat. Mix parts A & B of ‘Intergard 269’ primer in a 4:1 volume ratio and apply as per manufacturer’s TDS reference ‘206’, dated ‘11/03/2016’. Cure for 24 hours@10°C. Mix parts A & B of ‘Interline 975’ coating in a 2.2:1 volume ratio and apply as per manufacturer’s TDS reference ‘4236’, dated ‘04/02/2015’. Cure for 14 days@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Safecure Super’. White coloured, spray applied SBR latex solution intended to act as a concrete curing membrane. Apply as per manufacturer`s 'Tech Data Sheet no. 306', 'Revision no. v4', dated '02.01.2026'. Cure for 14 days at 25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PT-100' Grease. White coloured (opaque), non-miscible grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'MACONSIL 2312 E'. White coloured (opaque) silicone-based lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Durethan BKV30F 901510 SR1'. Black coloured, injection moulded nylon material. For use with water up to 65°C.
'Grilamid TR ICR 12 LS natural' (appears white, transparent), 'Grilamid TR ICR 12 LS yellow 6908' (yellow coloured) and 'Grilamid TR ICR 12 LS blue 4271' (blue coloured). Injection moulded PA MACM12/X materials. For use with water up to 85°C.
'Neproplast HDPE Fittings'. Black coloured, injection moulded HDPE (PE100) fittings. For use with water up to 60°C.
'FIRAT HDPE 100 fittings'. Black coloured, injection moulded HDPE electrofusion fittings. For use with water up to 23°C.
'FIRAT HDPE 100 Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 23°C.
'Polyatlas PE100 Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 23°C.
Hostalen 4731B HDPE-HT. White coloured, extruded polyethylene material. For use with water up to 60°C.
'MD1001 PPR Pipe'. Green coloured, extruded PPR pipe. For use with water up to 65°C.
'Repair Stick Steel' & 'Repair Stick Stainless Steel'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per manufacturer’s TDS dated 17.09.2025. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemiline AE 004 FB 26'. Black coloured, butyl material manufactured by calendaring. Shore hardness 65A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EP-G70B' Gaskets and 'O' rings. Black coloured, compression moulded, EPDM gaskets and 'O' rings. Shore hardness 70. Tested in-radius size 1.6mm. For use with water up to 23°C.
'EPDM-825-cmk (H80)/mld'. Black coloured, compression moulded EPDM material. Shore hardness 80 ShA. Tested in-radius size 1.13mm. For use with water up to 23°C.
'YL-EA-70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 65°C.
'Chemiline AG 030 FB 62'. Black coloured, EPDM material manufactured by calendaring. Shore hardness 60A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'603.0703.046 - EPDM PX Black SH 78'. Black coloured, injection moulded EPDM material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 10 of 11
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
