Spring loaded resilient trim check valve cartridge with stainless steel spring and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar. BS6920 at 85°C
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of push button ceramic cartridge headworks with a plastic body and EPDM seals. For insertion into specifically dimensioned tap assemblies Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Thermostatic cartridge with plastic body incorporating EPDM ‘O’-rings and stainless steel strainer. To be installed into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Spout outlet consisting of a chromium plated brass body, plastic aerator and EPDM ‘O’ rings. Maximum operating temperature 60°C.
Range of wall-mounted spout outlet consisting of a brass body with various finishes, plastic aerator and EPDM ‘O’ rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of expansion vessels with epoxy coated steel bodies and EPDM diaphragms. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Maximum operating temperature 70°C or 100°C (please refer to model).
Range of shock arrestors with stainless steel bodies and EPDM diaphragm. Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of expansion vessels with epoxy coated steel bodies and EPDM diaphragms. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Maximum operating temperature 70°C or 100°C (please refer to model).
Range of expansion vessels with epoxy coated steel bodies and EPDM diaphragms. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Maximum operating temperature 70°C or 100°C (please refer to model).
Range of vertical expansion vessels with EPDM membranes and stainless-steel connections. Maximum working pressure: 15.0 bar (0,16 litre model), 10.0 bar (0,6 litre up to 2.0 litre models), 8.0 bar (5 litre up to 40 litre models).
Non-metallic materials and components comply with BS6920 at 85°C
Filling loop assembly comprising of a spherical valve, stainless-steel braided EPDM lined flexible hose and a double check valve assembly ((suitable for backflow protection against fluid category 3) which incorporates a lever operated spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
Filling loop assemblies comprising of a stainless steel braided, EPDM lined hose, double check valve assembly with isolation valve verified by test (suitable for backflow protection against fluid category 3) and either a straight or tee isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of filling loop assemblies consisting of an in-line isolation valve, in-line double check valve assembly which also incorporates an isolation valve (suitable for back flow protection against fluid category 3) and stainless steel braided EPDM lined hose. The isolation valves are operated via a single lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Blutron’ plastic bodied filter head incorporating EPDM ‘O’-rings for use with filter cartridges (not supplied).For use with LLDPE tube (manufactured to DIN 8072). All models can be specified with or without an integral bracket. Maximum working pressure 6.0 bar. Cold water use only.
SD 200` pressure augmenting fire sprinkler device comprising of an end suction fire pump with a non-return valve on its outlet, multistage jockey pump with a lever operated spherical valve and non-return valve on its outlet, galvanised steel and copper pipework, pressure switches and gauges, pump sensing unit and two stainless steel braided EPDM lined hoses. Maximum working pressure 11.0 bar. Cold water use only.
‘F18’ range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with RIIFO B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of ‘Henco Profit Synthetic’ pushfit fittings with PPS (HPK models) or brass (HP models) bodies and EPDM o-rings, to be used with ‘Henco RIXc’ PEXc/Al/PEXc multilayer pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of MM and MC press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with AIS XPERT multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Range of press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with Multitubo multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Stainless steel press fittings incorporating EPDM ‘O’-rings for above ground use only. To be used with stainless steel 316L pipe (EN 10312). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of Talbot pushfit fittings with polyprolylene or acetal bodies and EPDM o-rings for use with MDPE PE80 pipe (BS EN 12201). For use above and below ground use. Maximum working pressure 16 bar. Cold water use only.
AMEX-10 Vario internal pipe repair kit incorporating stainless steel retaining rings and EPDM seal. Maximum operating temperature 23°C.
Non-metallic materials and components comply with BS6920 at 23°C
Range of water meters with brass bodies, plastic transducers, and EPDM O-rings. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
‘JS’ range of water meters with brass bodies and EPDM ‘O’-rings and plastic strainer on inlet. Maximum working pressure 16 bar. Cold water use only.
Range of ultrasonic water meters with brass bodies and EPDM O-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Water meter with a plastic body and working chamber incorporating and EPDM ‘O’-ring, NBR ‘O’-ring and seal. Available with a mechanical or electronic register. Maximum working pressure 16.0 bar. Cold Water use only.
Range of water meters with brass bodies, with integral plastic strainer and EPDM ‘O’- rings. The product is supplied with an optional combined plastic washer and stainless-steel strainer for installation on the inlet. Maximum working pressure 16.0 bar. Cold water use only.
Range of water meters with plastic or brass bodies, incorporating EPDM O-rings. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with DZR brass bodies and EPDM ‘O’-rings. The inlet incorporates either a plastic or stainless steel strainer (see model). The product is supplied loose fibre gaskets for installation on the inlet and outlet. Maximum working pressure 16.0 bar. Cold water use only.
Range of ultrasonic water meters with plastic bodies and transdcuers, and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. BS6920 50°C.
Range of water meters with blue epoxy coated ductile iron body, incorporating an EPDM diaphragm, NBR ‘O’ rings, stainless steel strainer and a polypropylene rotor. The products incorporate a second bypass meter assembly and a check valve cartridge (however, the complete product has not been fully tested for and is not intended to provide backflow protection). Maximum working pressure 16.0 Bar. Cold water use only.
Range of ultrasonic water meters with blue epoxy coated cast iron bodies, EPDM ‘O’-rings and plastic flow straighteners. Maximum working pressure 16.0 bar (DN50 to 200) or 10.0 bar (DN200 only)
Non-metallic materials and components comply with BS6920 at 50°C
‘Wesan WP’ range of water meters with black epoxy coated cast iron bodies, plastic impellers and EPDM ‘O’-rings and seal. Maximum working pressure 16.0 bar. Cold water use only.
Magnetic non-return valve with a brass body and EPDM seals. Maximum working pressure 16.0 Bar. Cold water use only.
Range of hose assemblies. Models B0301-148036-000 & B0301-148038-000 comprise of a spherical valve, stainless-steel braided EPDM lined flexible hose and double check valve assembly (suitable for backflow protection against fluid category 3). Model B0301-148037-000 comprises of a double check valve assembly (suitable for backflow protection against fluid category 3), stainless-steel braided EPDM lined flexible hose and ‘T’ type spherical valve. Maximum working pressure 10.0 bar. Cold water use only.
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Three hole, basic rough-in set with a brass body, incorporating EPDM O-ring seals. The product is supplied with a shower hose and a stainless steel braided, silicone lined flexible connecting hose. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of circulating pumps with a bronze body, plastic impeller and EPDM gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘SCALA1’ range of booster pumps with plastic bodies, plastic impellers, EPDM and NBR ‘O’-rings. The product incorporates a non-return valve. Maximum working pressure 8.0 bar. Cold water use only.
Range of multistage centrifugal pumps, with stainless steel bodies (CRN models) or black coloured cataphoretic electrodeposition coated cast iron bodies (CR models), stainless steel sleeve and impellers. The products can be supplied with or without a sensor. Maximum working pressures (no. of stages in brackets): CR/CRN 95 (1-5): 16.0 bar. CR/CRN 95 (6-8): 25.0 bar. CRN 95 (9-12): 40.0 bar. CR/CRN 125 (1-4): 16.0 bar. CR 125 (5): 25.0 bar. CRN 125 (6-7): 25.0 bar. CRN 125 (8-12): 40.0 bar. CR 155 (1-4): 16.0 bar. CRN 155 (1-4): 16.0 bar. CRN 155 (5-6): 25.0 bar. CRN 155 (7-11): 40.0 bar. CR/CRN 185 (1-3): 16.0 bar. CR/CRN 185 (4-5): 25.0 bar. CR/CRN 185 (6-8): 40.0 bar. CR/CRN 215 (1-3): 16.0 bar. CR/CRN 215 (4-5): 25.0 bar. CR/CRN 215 (6-7): 40.0 bar. CR/CRN 255 (1-3): 16.0 bar. CR/CRN 255 (3-4): 25.0 bar. CR/CRN 255 (5-6): 40.0 bar. When a sensor is incorporated the maximum working pressure is as follows: 25.0 bar with either the IPS44 or VTU sensor, (unless they are used on a pump with a maximum working pressure of 16.0 bar, in this instance the lesser pressure applies). The MBS3000 sensor can be used on all models, the pump maximum working pressure applies. Cold water use only.
Range of two stage horizontal water pumps with plastic bodies, stainless steel impellers and shaft, incorporating EPDM gaskets and seals. The products also incorporate a non-return valve (not suitable for backflow protection) and an shock arrestor expansion vessel. Maximum working pressure 1.8 bar. Cold water use only.
Horizontal 5 stage pump with stainless steel body, stainless steel impellers, EPDM and silicone ‘O’-rings. Maximum working pressure 6.2 Bar. BS6920 40°C.
Range of vertical multistage pumps with either stainless-steel bodies or cast-iron bodies with a black epoxy powder coating, stainless-steel impellers, shaft and outer sleeve, EPDM ‘O’-rings and a silicon carbide + EPDM shaft seal. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of shower outlet with plastic bodies (chromium plated) and plastic flow regulators. Model 27.369 supplied with a PVC multi-layered shower hose with EPDM washer and plastic strainer on inlet. Maximum working temperature 60°C.
Range of ceiling mounted, shower outlets with chrome plated brass bodies, EPDM seals, stainless steel strainer and flow regulator in the inlets. Supplied with a flexible hose. Maximum working temperature 60°C
Range of overhead shower outlets with chromium plated plastic bodies. The inlets incorporate combined EPDM washers and stainless-steel strainers. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted shower arms, (brass bodies - various finishes) incorporating EPDM ‘O’- rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted, overhead shower outlets with brass bodies (chromium plated), EPDM o-rings, fibre gasket and strainer at the shower head inlets. Multiple spray patterns available which is controlled via solenoid valve and a touch sensor. Product incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum working temperature 60°C.
Shower handset, chrome plated plastic incorporating EPDM ‘O’-rings.. Maximum operating temperature 60°C
Ceiling mounted shower outlet with chromium plated brass body, EPDM o-rings and a plastic flow regulator at the inlet. Maximum operating temperature 60°C
Shower kit comprising of a plastic shower handset incorporating a plastic flow restrictor, PVC lined shower hose that incorporates EPDM washers and riser rail assembly, available in various finishes.
Non-metallic materials and components comply with BS6920 at 65°C
Range of shower handsets with plastic bodies (chrome plated). The overhead showers incorporate a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Range of in-line Y-pattern strainers with blue epoxy coated ductile iron bodies, EPDM ‘O’-rings and a stainless-steel mesh. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ‘Y’- pattern strainers with brass bodies incorporating stainless steel filters and EPDM ‘O’-rings. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flow switch with a black plastic (nylon) body and an EPDM ‘O’-ring. The product incorporates a plastic filter on the inlet. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of nylon braided hoses with TPSiV inner liner and brass end connections incorporating EPDM washers.Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of PVC shower hoses with a black PVC inner liner (with a black and silver striped appearance). Hose end connections and nuts are available in brass, plastic or stainless steel, (all chrome plated), with either EPDM (black) or silicone (white) washers. BS6920 65°C.
Range of plastic shower hoses (various finishes) incorporating PEX inner liner, with EPDM washers. Maximum working pressure; Open outlet Maximum operating temperature; 65°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of PVC shower hoses with a black PVC inner liner (with a black and silver striped appearance). Hose end connections and nuts are available in brass, plastic or stainless steel, (all chrome plated), with either EPDM (black) or silicone (white) washers. BS6920 65°C.
White PVC shower hose, with EPDM washers. BS6920 65°C.
Black PVC lined flexible shower hose with chrome plated metal outer sheath and EPDM washer. Maximum operating temperature 65°C.
Range of PEX or PVC lined interlocked shower hoses (chrome plated) incorporating a stainless steel EPDM strainer washers or EPDM washers. Maximum operating temperature 85.0°C (PEX models) or 65.0°C (PVC models).
Range of stainless steel interlocked shower hoses with PVC inner liner and EPDM gaskets and stainless steel strainers.
Non-metallic materials and components comply with BS6920 at 65°C
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of shower hoses. Model ML-PVC-DCHS01-XX is a PVC hose incorporating EPDM, NBR or Silicone seals. Model ML-SS-SKHS01-XX is a PVC or EPDM lined shower hose incorporating EPDM, NBR or silicone seals with a stainless-steel interlocked outer with (various finishes).
Non-metallic materials and components comply with BS6920 at 65°C
Range of Stainless steel braided EPDM lined flexible hose assemblies with a variety of brass end connections. Maximum working pressure 10.0 bar. Maximum operating temperature: 85°C
Qualflex classic range of stainless steel braided EPDM lined flexible hoses incorporating EPDM O-rings. Maximum working pressure at 20°C ,10.0bar and maximum working pressure at 65°C , 6.0bar. Maximum operating temperature 65°C.
‘Comfortflex’ range of silver braided shower hoses with a TPE inner hose and EPDM seals.Open outlet
Non-metallic materials and components comply with BS6920 at 60°C
Range of stainless-steel braided EPDM lined flexible hose assemblies incorporating EPDM washers and ‘O’-rings, and various end connections, some of which include a brass bodied screwdriver operated spherical valve with chrome plated brass ball (see model). For use with copper pipe (EN 1057) Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel braided, PEX lined flexible hose assemblies with EPDM washers and O ring incorporating an isolation valve (brass body and ball), tee piece (brass) and incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of automatic air vent valves with blue epoxy coated cast iron bodies and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
T-type thermostatic mixing valve with brass body incorporating EPDM ‘O’ rings and stainless steel springs. Maximum working pressure 16 bar. Maximum operating temperature 85°C
Wall mounted thermostatic shower valve (chrome plated brass), incorporating a ceramic disc diverter cartridge controlling the flow from shower to shower with a cube operating member. The temperature is controlled independently via a thermostatic cartridge, with a cube operating member, that also incorporates a manual override button. The product is supplied with a chrome plated shower handset, shower hose and riser rail assembly. The inlets incorporate approved check valve cartridges, (however, the complete product has not been fully tested to demonstrate that it provides backflow protection), chrome plated spherical ball valves and stainless-steel strainers with EPDM gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted blending thermostatic shower valve (chrome plated brass), incorporating a quarter turn ceramic disc headwork controlling the flow. The temperature is controlled independently via a thermostatic cartridge. Both using cube type operating members. The inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow protection. The inlets also incorporate ¾” BSP (M) x 15mm compression (chrome plated) spherical ball valves and EPDM washers incorporating stainless steel mesh strainers. The product is supplied with a chrome plated shower handset, shower hose and riser rail assembly. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, exposed, thermostatic shower mixing valve (black plated brass). The products incorporate a ¼ turn ceramic disc. Temperature is controlled independently via a thermostatic cartridge with a manual override button. The products have a dome type operating member. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating) and EPDM seats. Supplied with a rotating wheel operating member. Maximum working pressure:10Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. The valves can either be lever or gear operated via a handwheel. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer or lug type butterfly valves with blue epoxy coated cast or ductile iron bodies, blue epoxy coated ductile iron or stainless-steel discs and EPDM seats. Leaver or hand wheel operated. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies, nickel plated discs and EPDM rubber seat. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lugged and double flanged type butterfly valves (with blue epoxy coated ductile iron bodies, and either a stainless steel or grey epoxy coated ductile iron disc with an EPDM liner. Maximum working pressure 16.0 Bar (DN50 to DN800) or 10.0 Bar (DN900 to DN1200)
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with handwheel gear operating members. Maximum working pressure – 10 bar or 16 bar, see models. Maximum operating temperature – 23°C.
Range of lever operated butterfly valves with blue epoxy coated cast iron bodies, stainless steel discs and EPDM ‘O’ rings and seals. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of butterfly valves with ductile iron bodies (blue epoxy coating) and EPDM seats. Supplied with a rotating wheel operating member. Maximum working pressure:10Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer type & lug type butterfly valves with blue epoxy coated ductile iron (V9911 & V9912) or stainless steel bodies (V9952), stainless steel discs and EPDM seats. The products are supplied with either a lever, gearbox (below DN250), electric or pneumatic actuating operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, incorporating EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Wall mounted, concealed shower control valve with a brass body, incorporating a non-rising spindle headwork and EPDM O-rings. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
‘Aquacheck’ range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel springs and EPDM seals. Maximum working pressure 16 bar. Cold water use only.
ART 236 range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel springs and EPDM seals. Maximum working pressure 16 bar. Cold water use only.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM coated discs. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Non-metallic materials and components comply with BS6920 at 85°C
Range of swing gate non-return valves with blue epoxy coated ductile iron bodies and EPDM discs. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Inlet control group consisting of an in-line pressure reducing valve (adjustable pressure - see model) and a pre-set expansion relief valve (pre-set pressure - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe EN1057 only. Maximum supply pressure 10.0 bar. Maximum operating temperature 40°C.
Range of pilot operated, pressure reducing valves with blue epoxy coated ductile iron bodies, stainless steel filter, EPDM ‘O’-rings and diaphragm. The valve has an adjustable pressure reducing facility controlled via a pilot valve, with auxiliary components including stainless steel tubing and fittings, and stainless-steel spherical valves. Maximum inlet supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 1.0 - 12.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Pressure relief valves with a DZR brass body, EPDM diaphragm and manually operated easing gear, preset at 3 bar. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pre-set pressure relief valves (set at 3.0 bar) with nylon bodies, EPDM diaphragms and ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure relief valves with gunmetal bodies, EPDM diaphragms and lever operated easing gear. The relief setting is between 0.5 - 16.0 bar depending on the model. Maximum operating temperature 99°C
Range of latching solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings.. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of normally closed solenoid valves with black or grey plastic bodfies, EPDM diaphragm and EPDM ‘O’-rings. The inlet incorporates a removable plastic strainer with a stainless steel mesh. The outlet incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of normally closed solenoid valves with plastic bodies, EPDM ‘O’-rings and diaphragm. The inlet incorporates a combined plastic filter and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of plastic solenoid valves with an EPDM diaphragm and ‘O’-rings. The inlets incorporate a stainless-steel strainer (except for push fit inlet models). Push fit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. BS6920 70°C.
Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. Maximum working pressure 8.0 bar. Can only be used with water at 70°C. BS6920 70°C.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel spherical valves, incorporating a stainless-steel ball, PTFE seats and EPDM ‘O’-rings with single lever operating members. Maximum working pressure 63.0 Bar. Maximum operating temperature 23.0°C
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
‘3029’ range of lever operated spherical valves with chromium plated brass bodies and balls, incorporating PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of bronze spherical valves, incorporating chrome plated brass balls, PTFE seats and EPDM O-rings. Model (BW-Q01) incorporates a single lever operating member. Model (BW-Q01B) incorporates a butterfly type operating member. Maximum working pressure 16 bar. Maximum operating temperature 85°C
Range of press fit spherical valves with DZR brass bodies and balls with EPDM O-Rings. Joints are achieved by the use of a press fitting tool. For use with Multi-layered Pert/Al/Pert pipe compliant to EN21003-2 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of spherical valves with brass bodies and stems, incorporating chrome plated brass ball and EPDM O-rings and single lever operating members. Maximum supply pressure 24.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
In line isolation valve with DZR brass body, DZR brass ball (chrome plated), and an EPDM inlet washer. The product incorporates two approved check valve cartridges, one either side of the spherical valve, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar. BS6920 85°C.
Range of in-line lever or screwdriver operated spherical valves with DZR brass bodies (nickel plated) and brass balls (chromium plated), EPDM ‘O’-rings and PTFE seats. The ball can incorporate a plastic flow regulator, or a stainless-steel strainer (within a plastic housing) inserted through the side port. Compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: Spherical valves only and those incorporating a stainless-steel strainer: 85°C. Spherical valves incorporating a plastic flow regulator: 60°C.
Range of push fit shut off valves with plastic bodies incorporating EPDM ‘O’ rings and seals, for PE-X pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipe (manufactured to BS EN1057) Maximum working pressure/temperature: 12.5 Bar at 20°C and 6.0 Bar at 65°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges, EPDM gasket and ‘O’-ring. The valves operate via non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50: 25.0 bar, DN65-DN600: 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising resilient stem seated gate valves with epoxy coated bodies and EPDM wedge. Maximum working pressure 16 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron bodies ,EPDM gasket, EPDM wedge and a handwheel operating member. Maximum working pressure 25 bar. Maximum operating temperature 80°C
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies (green epoxy coated) and EPDM coated ductile iron wedge. Maximum working pressure – 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM encapsulated wedge. The gate is operated via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated cast iron bodies, incorporating cast iron wedges encapsulated in EPDM. Maximum working pressure - 16 Bar Maximum operating temperature – 23°C.
Double flanged, gate valve with blue epoxy coated ductile iron body and EPDM coated wedge and handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 71°C
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only.
Range of cast iron gate valves with blue epoxy coating, EPDM coated disc, PTFE gasket and EPDM seals. The valves are operated via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM encapsulated wedge. The gate is operated via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue, black or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coating ductile iron bodies and wedges and EPDM ‘O’-rings. The valves operate using a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of brass and DZR brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of screw down stop valves with brass bodies and EPDM gaskets. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of unvented monobloc groups consisting of an in-line pressure reducing valve (PRV) (adjustable between 2.7 and 3.3 bar or 3.2 and 3.8 bar - see model) and a pre-set expansion relief valve (SRV) (pre-set at either 4.5, 4.75, 5.0, 6.0 or 8.0 bar - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The expansion relief valve is fitted with a rotary type easing gear and the products are for use with copper pipe (manufactured to EN1057). Maximum inlet supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermal balancing valves with brass bodies and EPDM O-rings. The products also incorporates an analogue temperature gauge. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 90°C
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
'Drincable'. Blue coloured, extruded, EPDM rubber electrical cable. Shore hardness 50. Tested in-radius size 0.90mm. For use with water up to 23°C. This approval is for complete cable, the blue coloured outer part being the water contact layer.
'E7518'. Black coloured, injection moulded EPDM C-seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP90/4 BLK Seals and 'O' rings'. Black coloured, injection moulded EPDM seals and 'O' rings. Shore hardness 90. The seals have a tested in-radius size of 1.7mm. The 'O' rings have a tested in-radius size of 1.2mm. For use with water up to 85°C.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'70528'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 72 A. Tested in-radii sizes between 1.4mm & 1.8mm. For use with water up to 85°C.
'LOPI50'. Black coloured, injection moulded EPDM 'O'-ring. Shore hardness 50. Tested in-radius size 2.5mm. For use with water up to 85°C.
'9710-ALT 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size between 1.0mm & 2.0mm. For use with water up to 23°C.
'LOPI50'. Black coloured, injection moulded EPDM 'O'-ring. Shore hardness 50. Tested in-radius size 2.5mm. For use with water up to 85°C.
'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'01/U80EP'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 1.00mm & 2.5mm. For use with water up to 85°C.
'EP7/3/7 BLK O-rings & gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 75. The gaskets have an in-radius size of 1.0mm. The 'O' rings have an in-radius size of 1.3mm. For use with water up to 85°C.
'EP70 BLK Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 70. Tested in-radius size 1.0mm. In April 2024, 'EP70 BLK 'O' rings’, black coloured, injection moulded 'O' rings were added to the approval. Shore hardness 70. Tested in-radius size of 1.3mm For use with water up to 85°C.
'HH7118F 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EUW-70'. Black coloured, injection moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 60°C.
‘SMS-8000-Premium’. Black coloured, compression moulded EPDM material. Shore hardness 80 respectively. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NPEPDM-80'. Shore hardness 80. 'NPEPDM-50' was added to the approval in December 2023. Shore hardness 50. Black coloured, compression moulded, EPDM materials. Tested in-radius size 1.0mm. For use with water up to 70°C.
'334701 - EPDM peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Ganga 50, 60, 70, 80 & 90'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 90 ShA. Tested in-radius size 1.1mm. For use with water up to 85°C.
'EPDM50BKWS, EPDM55BKWS, EPDM60BKWS, EPDM65BKWS, EPDM70BKWS, EPDM75BKWS & EPDM80BKWS'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 23°C.
Sunaflex® T 8715. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.00mm. For use with water up to 23°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 30114010102A Black'. Black coloured, compression moulded EPDM sheet material. Shore hardness 75. Tested in-radius size 3.0mm. For use with water up to 85°C.
'PT0165/2'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'HBHG'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AquaFlex T 5857'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
'334137 – EPDM Peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'PT0469'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP002971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7001165PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM HT5697-4A'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. Between May 2024 and October 2024, the material was for use with water up to 50°C. Between November 2024 and May 2029, the material is for use with water up to 60°C.
'ML 57302'. Black coloured, compression moulded EPDM material. Shore hardness 55A. Tested in-radius size 1.0mm. For use with water up to 23°C.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Spring-loaded resilient trim in-line check valve cartridge with a plastic body, incorporating a stainless-steel spring and EPDM ‘O’-rings . For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring-loaded resilient trim in-line check valve cartridges with plastic bodies, incorporating a stainless-steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Flow regulator incorporating a plastic body and EPDM O-ring. Maximum operating temperature 65.0°C.
Ceramic cartridge headwork with plastic body & EPDM seals. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with a plastic body incorporating EPDM ‘O’ rings and a stainless teel strainer. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with a plastic body, incorporating EPDM ‘O’-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar. Maximum operating temperature 65°C.
Range of ¼ turn ceramic disc headworks with brass bodies, EPDM ‘O’-rings and either a red or blue silicone gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body and EPDM gaskets and seal rings. For insertion into specifically dimensioned bores Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies, stainless steel mesh strainer and EPDM ‘O’ rings. For insertion into specifically dimensioned bores.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass elbows for combination tap assemblies with EPDM gaskets and pillars to suit bath mixers. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of expansion vessels with stainless steel bodies and EPDM membranes. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of vertical and horizontal expansion vessels with EPDM membrane and stainless steel or galvanised steel connections. Maximum working pressures 10.0. Maximum operating temperature 85 °C.
Range of shock arrestors with stainless steel bodies and EPDM diaphragm. Maximum working pressure 10 bar. Maximum operating temperature 70°C
Zilmet range of cylindrical or tubular expansion vessels, epoxy coated carbon steel bodies with either Butyl or EPDM membranes and stainless-steel or galvanized carbon-steel connections. Please refer to models for maximum working pressures, as this varies by model and size. Maximum operating temperature 65°C.
Range of filling loop assemblies, consisting of either a stainless steel braided, EPDM lined flexible hose assembly (300616 VIS and 300614 VIS) or a rigid copper tube assembly (3006315 VIS), a lever operated spherical valve and an in-line, non-verifiable double check valve assembly verified by test (suitable for backflow protection against fluid category 3) which incorporates an integral lever operated spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C , and 85°C for 300615 VIS.
Range of filling loop assemblies, incorporating a stainless steel braided EPDM lined flexible hose, brass bodied isolation valve and a DZR brass non-verifiable double check valve assembly that incorporates an isolation valve. Model FL12041510 has a lanyard and end caps. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of filling loop assemblies, consisting of: A nickel plated DZR brass bodied isolation valve with chrome plated DZR brass ball and integral non-verifiable double check valve assembly, verified by test (suitable for backflow protection against Fluid Category 3). A stainless-steel braided EPDM lined flexible hose assembly. An isolation valve with a nickel plated DZR brass body and a chrome plated DZR brass ball. The HLD14.12.049 model is supplied with a lanyard and cap end for each valve. The compression connections are for use with copper pipe (manufactured to BS2871). Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of filter cartridges and housings with plastic bodies (various finishes, see models), EPDM O-rings and PSF membrane. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 6 bar. Maximum operating temperature 50.0°C.
Range of stainless steel press-fit fittings and pipes, the fitttings incorporating stainless steel bodies and EPDM O-ring. Joints are made using a pressing tool for M profile. All the models are for both above ground and below ground use. YHPFM304 models are made of SS304 stainless steel, used with Yuhe SS304 pipes manufactured to EN10312. YHPFM316L models are are made of SS316L stainless steel, used with Yuhe SS316L pipes manufactured to EN10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of stainless steel press-fit fittings (316L) and pipes (316L - EN 10312), the fitttings incorporate EPDM O-rings. Crimp joint is achieved by a M profile crimp jaws. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of stainless steel press-fit fittings (316L or 304) and pipes (SUS316L or SUS304 - EN 10312), the fitttings incorporate EPDM O-rings. Crimp joint is achieved by a M profile crimp jaws. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of M type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings and pipe. Fittings incorporate EPDM ‘O’-rings Maximum working pressure 10 bar. Maximum operating temperature 95°C
‘SharkBite’ range of brass push fit fittings incorporating an EPDM ‘O’-ring. For use with the following pipes: JG Speedfit Layflat Polybutylene Barrier Pipe (JG BPB pipe manufactured to BS EN 7291-2:2010), 'BPEX' Barrier Pipe (JG BPEX pipe manufactured to BS EN 7291-3:2010), Polybutylene barrier pipe (manufactured to BS EN 7291-2:2010), PEX barrier pipe (manufactured to BS EN 7291-3:2010) and Copper pipe (manufactured to BS EN1057:2006). Maximum working pressures and operating temperatures: When used with Polybutylene barrier pipes (manufactured to BS EN 7291-2:2010) and PEX barrier pipes (manufactured to BS EN 7291-3:2010): 12.5 bar, cold water use only. 6.0 bar @ 95°C. When used with copper pipe (manufactured to BS EN1057:2006): 10mm sizes: Maximum working pressure 16.0 bar. Cold water use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. 15-22mm sizes: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C. 28mm size added April 2024: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pipe repair clamps incorporating EPDM double seals. The products are intended for use with stainless steel pipe manufactured to EN1124. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of urinal flushing mechanisms with a solenoid valve controlling the flow with EPDM rubber diaphragm. The valves are controlled via an infra-red sensor. The product also incorporates a servicing valve, DC pipe interrupter and flow regulator. Maximum working pressure - 6 Bar. Maximum operating temperature - 23 °C.
Range of packaged plate heat exchangers comprising of stainless steel plates with EPDM gaskets. The products are supplied with twin primary circulation pumps, a secondary circulation pump, 3 port control valve and a control panel with full Mod BUS BMS connectivity. Maximum working pressure - Primary and Secondary circuits 10.0 bar. Maximum operating temperature 85°C.
Range of integrated water circuits with plastic bodies and EPDM ‘O’ rings and gaskets. The assemblies incorporate flow switches, plate heat exchangers and plastic flow regulators. The primary circuit incorporates a 3.0 bar rated pressure relief valve. Maximum working pressures: 2.5 bar primary circuit, 10.0 bar secondary circuit. Maximum operating temperature 85°C.
‘Gladiator’ range of in-line water meters with polyamide bodies and EPDM rubber `O` rings. The meters incorporate a plastic strainer. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Range of rotating piston volumetric water meters with brass or nylon PA66 bodies, incorporating EPDM O-rings and plastic strainers at the inlets. Maximum working pressure 16.0bar.
Non-metallic materials and components comply with BS6920 at 50°C
CZ4000 range of in-line water meters with polyamide bodies and EPDM rubber `O` rings. The meters incorporate a plastic strainer. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with black epoxy coating bodies, plastic impellers and EPDM ‘O’ rings. Maximum working pressure – 16.0 Bar. Cold water use only.
Isolation valve, stainless-steel braided EPDM lined flexible hose assembly and a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). For use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel bodied mechanical pump shaft seals. The 491 model comprises of carbon and silicone carbide seal faces and EPDM ‘O’-rings. The 1510 model comprises of carbon and silicone carbide seal faces, EPDM ‘O’-rings and an orange NBR/aramid fibre gasket. Maximum operating temperature 100°C.
Range of self-acting controllers with brass bodies, EPDM O rings and gaskets. Maximum working pressure 16.0 Bar Maximum operating temperature of the secondary circuit is 65˚C and the primary circuit is 99˚C
Range of flow-compensated (thermostatic) temperature controllers incorporating a brass body with EPDM ‘O’-rings and gaskets. The valves incorporate a non-rising spindle headwork for temperature regulation. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C
Range of hoses with EPDM, PVC or PEX inner tubes and a corrugated stainless-steel tube. The outlets incorporate a plastic aerator. Maximum operating temperature 65°C, open outlet use.
‘SCALA1 TWIN’ range of booster pump sets, comprising of two pumps with plastic bodies, plastic impellers, EPDM and NBR ‘O’-rings and an accessory set consisting of a base plate, plastic manifold and four brass spherical valves. Each pump incorporates a non-return valve. Maximum working pressure 8.0 bar. Cold water use only.
`UPM3` range of single stage circulator pumps, with stainless steel or plastic bodies, plastic impellers, ceramic shafts and bearings, EPDM 'O'-rings and seals. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
‘Right Pump’ range of single and twin pumps with plastic bodies. The universal models incorporate a non-return valve on the outlet(s) of the pump body (x2 for the RP50TU model) and an expansion vessel. The twin models incorporate a bypass tube between each side of the pump. The inlet(s) of the pump body incorporate(s) a combined EPDM washer and stainless-steel strainer. The inlet and outlet hoses incorporate an isolation valve on the pushfit connection. The push fit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 1.5 to 3.6 bar (see model). Maximum operating temperatures 60°C.
Range of colour coded disposable shower kits incorporating a white PVC shower hose with EPDM washer and shower handset incorporating a plastic body (white), NBR ‘O’-rings, and a coloured locking ring around the shower face. Maximum working pressure: 5.0 bar Maximum working temperature: 60°
Range of Shower handsets with plastic bodies (chrome plated). The overhead showers incorporate a combined EPDM washer and stainless-steel strainer on the inlet. Maximum operating temperature 65°C.
Range of medical shower handsets incorporating plastic bodies and EPDM O-rings with various inserts. Supplied with PVC/PEX lined shower hoses incorporating EPDM washers. Maximum operating temperature 65°C. Open outlet use only
Range of overhead shower outlets with chromium plated plastic bodies. The inlets incorporate combined EPDM washers and stainless-steel strainers. Maximum working pressure: open outlet use only Maximum operating temperature 60°C
Range of shower arms and ceiling connectors (brass bodies – various finishes) & overhead shower outlets (plastic bodies - various finishes), incorporating EPDM O rings, plastic flow regulators and stainless-steel strainers. Open outlet use only Maximum operating temperature 60.0°C
Range of shower arms and ceiling connectors (brass bodies – various finishes) & overhead shower outlets (plastic bodies - various finishes), incorporating EPDM O rings, plastic flow regulators and stainless-steel strainers. Open outlet use only. Maximum operating temperature 60.0°C
Hand shower outlet with plastic bodies (various finishes, see models) incorporating a PSF membrane filter and EPDM O-rings. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature: 50°C.
Range of ‘Y’- pattern strainers with cast iron bodies (blue epoxy coated) and brass plugs (EN12164), incorporating stainless steel filters (EN10088) and EPDM ‘O’-rings. Maximum operating pressure 16 bar. Maximum operating temperature 100°C
Range of drain valves with bronze bodies, EPDM seat and ‘O’-rings. The products incorporate a rising spindle operating mechanism and a hose union outlet connection. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of stainless steel (various finishes) interlocked shower hoses with PVC liner and EPDM gaskets.Open outlet use only
Non-metallic materials and components comply with BS6920 at 85°C
Range of PEX or PVC lined shower hoses with a chrome plated interlocked stainless steel outer and EPDM washers. Maximum operating temperature 60°C.
Range of PVC or EPDM lined shower hoses with stainless steel outer (chrome or black finish) or PVC reinforced (chrome plated finish) outer layer. Maximum operating temperature 65°C.
Range of nylon or stainless steel braided flexible hose assemblies incorporating a PE-X inner hose, EPDM ‘O’-rings and/or gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel interlocked shower hose with PVC inner hose and EPDM O-rings, various finishes. Open outlet use only. Maximum operating temperature 65°C.
Range of nylon braided (DG50X model series) or stainless steel braided (DG10X model series), PEX lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections (see models). Some models incorporate a screwdriver operated isolation valve. All compression and push-fit connections are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 7.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of shower hoses with a rubber outer layer (various finishes, see models) and either PVC or PEX inner liner (see models), EPDM or NBR O-rings (see models) and either brass or stainless-steel connectors (see models). Open Outlet use only. Maximum operating temperature 85.0°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel braided, EPDM lined flexible hose assemblies. Models are available with a variety of end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of nylon braided (DG50E model series) or stainless steel braided (DG10E model series), EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Stainless-steel braided EPDM lined flexible hose assembly with EPDM gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of double flanged, handwheel operated butterfly valves with blue epoxy coated ductile iron bodies, incorporating either stainless-steel or blue epoxy coated ductile iron discs and EPDM seals. Maximum working pressure 16.0 Bar (DN50 to DN300) or 10.0 Bar (DN350 to DN2000) Maximum operating temperature 23.0°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and stainless-steel discs incorporating EPDM rubber seats. (DN40 - DN200) incorporate a lever type operating member and (DN250 – DN500) incorporates a hand wheel type operating member. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer lugged and double flanged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. The valves can either be lever, wheel or gear operated via a handwheel. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wafer type butterfly valves (lever or hand wheel operation) with a blue epoxy coated ductile iron body, EPDM seat and stainless-steel disc. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of blue epoxy coated butterfly valves with stainless steel discs and EPDM seal. Maximum operating pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating) and EPDM seats. Supplied with a rotating wheel operating member. Maximum working pressure:10Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of doubled flanged butterfly valves with blue epoxy coated ductile iron bodies and discs, incorporating EPDM seals. Maximum working pressures 25.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated butterfly valves with blue epoxy coated ductile iron bodies and EPDM rubber seat. Maximum working pressure 16.0 Bar Maximum operating temperature 23.0°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
2-way ceramic disc diverter incorporating a brass body, EPDM ‘O’-rings and a silicone gasket. Maximum operating temperature 85°C.
Range of manually operated plunger valves with blue epoxy coated ductile iron bodies and EPDM seals. The flow is controlled via a handwheel. Maximum working pressure 25.0 Bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure reducing valves with a DZR brass body, stainless steel strainer and EPDM membrane. Maximum inlet supply pressure 25.0 bar. Outlet pressure in the range of 1.0-6.0 bar. Maximum operating temperature 80°C.
Range of in-line, adjustable, pressure reducing valves with DZR brass bodies and incorporating a stainless steel strainer. Maximum supply pressure 16.0 bar. Outlet pressure range 1.0 to 6.0 bar with an inlet pressure of up to 10 bar Outlet pressure range 2.0 to 6.0 bar with an inlet pressure above 10 bar Maximum operating temperature 60°C.
Pressure relief valves with a brass body incorporating EPDM ‘O’ rings for 35890040 and EPDM diaphragm for 35900040, pre-set at 3.0 bar. Model 35890040 incorporates a manually operated lever type lifting gear Maximum working pressure 10 bar. Maximum operating temperature 90°C.
Range of pressure relief valves with gunmetal bodies, EPDM diaphragms and lever operated easing gear. The relief setting is between 0.5 - 16.0 bar depending on the model. Maximum operating temperature 99°C
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of single lever ball valves with stainless steel bodies, ball, EPDM O-rings and PTFE gaskets. The press fit connection is to be used with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of TH profile pressfit brass bodied spherical valves with brass balls, EPDM O-rings and lever type operating members. Fittings for use with EN ISO 21003 Pert-al-Pert Multilayer pipe. Maximum working pressure 10 bar. Maximum operating temperature 95°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Electronically controlled spherical valve with smart water leakage shut off, incorporating ceramic pressure sensor, stainless steel ball and EPDM O-rings. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls and various operating members (see models). Products incorporate EPDM O-rings and PTFE seats. Maximum working pressure ½” – 1” 30 bar, 1 ¼” – 2” 25 bar. Maximum operating temperature 100°C.
Range of spherical valves with DZR brass bodies, chrome plated DZR brass or stainless-steel balls, EPDM ‘O’ rings and PTFE seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of gate valves with blue epoxy coated ductile iron bodies and disks, with EPDM O seats. The valves are operated via a non-rising spindle headwork and hand wheel. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with Red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ductile iron gate valves with blue epoxy coated bodies, EPDM wedges and EPDM O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 85.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies and EPDM wedge. Maximum working pressure 16.0 Bar. Maximum operating temperature 65.0°C.
Range of resilient seated gate valves incorporating blue epoxy coated ductile iron body and EPDM gaskets with a handwheel operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 23.0°C
Range of gate valves incorporating blue epoxy coted ductile iron bodies, ductile iron wedges encapsulated in EPDM and an EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-rising resilient stem seated gate valves with epoxy coated bodies and EPDM wedge. Maximum working pressure 16 bar. Cold water use only.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, epdm coated ductile iron wedges, EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of press fit screw down stop valves with brass bodies incorporating EPDM seat washers, PTFE seals and non-rising spindles operated via ‘T’ type operating members For use with copper tube to BS EN 1057. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass stop valves with non-rising stems, having brass bodies, EPDM ‘O’ rings and PTFE gaskets and various operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of combined stop valve and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves with bronze bodies, DZR brass disc and EPDM rubber 'O’-rings. Both models have test points. The F9506 models also have a drain point on the high-pressure test side. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of manually operated balancing valves with blue epoxy coated ductile iron bodies, incorporating EPDM ‘O’-rings and PTFE washers. Available in the following options: DN65-DN150 sizes: DZR brass sleeve. DN65-300 sizes: blue epoxy coated ductile iron sleeve. DN65-DN150 sizes: bronze disc. DN65-300 sizes: blue epoxy coated ductile iron disc. DN200-DN300 sizes: Stainless steel (SUS304) disc. DN200-DN300 sizes: Stainless steel (SUS304) stem. DN65-DN300 sizes: Stainless steel (SUS420) stem. DN65-DN150 sizes: brass stem. The product incorporates a test port on each flange and are adjusted using a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
'M534 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'M534 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'60EP126p'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.6mm. For use with water up to 85°C.
'EPDM 5070 Membrane'. Black coloured, compression moulded EPDM membrane. Shore hardness 58. Tested in-radius size 1.02mm. For use with water up to 85°C.
'EP703901 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'ERIKS 559706'. Black coloured, EPDM 'O' ring with a vulcanised joint, manufactured by extrusion. Shore hardness 70 ShA. Tested in-radius size 8.0mm. For use with water up to 23°C.
'EP70-S3150/B1-73898 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EPDM 5518 Seal 3G'. Black coloured, compression moulded, EPDM rubber seal. Shore hardness 58. Tested in-radius size 1.92mm. For use with water up to 23°C.
'EPDM 5711'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radii size between 0.5mm & 3.5mm. For use with water up to 85°C.
'JH3517-EPDM Gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 55. Tested in-radius size 1.6mm. For use with water up to 65°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SME001 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 60. In November 2024 'SME001 EPDM', a compression moulded EPDM rubber with a shore hardness of 75 was added to the approval so that a range with a hardness between 60 & 75 is covered by the approval. Tested in-radius size of 1.0mm and are for use with water up to 65°C.
'E59WKZ'. Black coloured, injection moulded EPDM rubber material. Shore hardness 58. Tested in-radius 1.0mm. For use with water up to 60°C.
'HT5557-10'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. Between January 2024 and March 2024, the material was for use with water up to 50°C. From April 2024 the material is for use with water up to 60°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'3E60B11P/3E60B18P & 3E70B03P/3E70B16P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EW gasket material'. Black coloured, injection moulded, EPDM gasket material. Shore hardness 65A. Tested in-radius size 3.9mm. For use with water up to 65°C.
'E6029 (shore hardness 70) & E6392 (shore hardness 80)'. Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ECW-70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 60°C.
'Jihua 3517'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP05280PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EH700-144'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EUW-75'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 60°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7041F'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of spring loaded resilient trim check valve cartridges with plastic bodies, stainless steel spring and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 16 Bar Maximum operating temperature 65°C (model OV15/DN15-EPDM 31.0001.0 only) Maximum operating temperature 85°C for all other models
Range of aerators with plastic bodies and EPDM ‘O’-rings. Model (SB-BTA) incorporates a (chrome plated brass) housing. Maximum operating temperature 85°C
Range of aerators with plastic bodies and EPDM ‘O’-rings. Open outlet use only. Maximum operating temperature 65ºC.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of horizontal and vertical expansion vessels with EPDM membrane and stainless-steel connections. Maximum working pressure: 8.0 bar (35 litre model); 10.0 bar (50 litre up to 400 litre models).
Range of filling loop assemblies consisting of an in-line isolation valve, in-line double check valve assembly which also incorporates an isolation valve (suitable for back flow protection against fluid category 3) and stainless steel braided EPDM lined hose. The isolation valves are operated via a single lever. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Inoxpres range of stainless-steel crimp fittings with EPDM ‘O’-rings and gasket for use with Inoxpres stainless-steel tube (1.4404 AISI 316L or 1.4521 AISI 444 – annealed or not-annealed). The connection is created by using a pressing tool. For above and below ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
Instantor Metric Copper Press Range crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of Cupro- Fit press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of ‘NiroSan’ stainless-steel crimped fittings incorporating EPDM ‘O’ Rings, for use with ‘NiroSan’, ‘NiroSan SF’ & ‘NiroSan -ECO’ stainless-steel pipe (all manufactured to EN10312). The fittings and pipe are assembled using a crimping tool with either ‘M’ (15-108mm), ‘V’ (15-54mm) or ‘SA’ (15-108mm) crimping profiles. For above ground use only. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.
Range of Reliable press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
‘Hansen easy fit’ range of polypropylene compression fittings with EPDM ‘O’-rings for use with metric PE80 (20mm-63mm) and PE100 (32mm-110mm) pipe to AS/NZS:4130 and plastic pipe inserts. For above and below ground use. Maximum working pressure: See models. Maximum operating temperature: Cold water use only.
IDC ‘BDGxxx’ range of press fittings with brass or nickel plated brass bodies (see model) incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). The BDG241 and BDG257 prefix models incorporate an EPDM gasket on the captive nut end connection. Pressfit jointing is achieved by either a U or TH crimping profile. Compression connections are for use with copper pipe 12-28mm (manufactured to EN1057) or Irish copper pipe 14.7-27.4mm (manufactured to EN1057). For above ground use only. Maximum working pressure 10.0 bar. 20, 25 & 26mm pressfit sizes cold water use only. Threaded, compression and 16 & 32mm pressfit sizes maximum operating temperature 95°C. From June 2025: The 20, 25 & 26mm pressfit sizes (TH profile only) maximum operating temperature 95°C.
Range of M profile brass press fittings with EPDM ‘O’-rings or gaskets to be used with copper pipe manufactured to EN1057 for above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
SANHA Press Series 6000 & 16000 and PURAPRESS Series 8000 of press-fit fittings with copper (6000), bronze (8000) and chrome plated copper (16000) bodies and EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of blue epoxy coated ductile iron dismantling fittings with EPDM sealing rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Helvatron H2O’ range of ultrasonic water meters with brass bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of submersible pressure sensors and hydrostatic transmitters (supplied in lengths up to 1000m). Cold water use only.
‘Monsoon Standard’ range of single and twin ended shower booster pumps with brass bodies, brass impellers, EPDM seals and NBR ‘O’-rings. The inlet(s) of the pump body incorporate(s) a plastic strainer. Models with push fit connections include an integral isolation valve. Pushfit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of horizontal or vertical multi-stage pumps with a stainless-steel body (HM models) or cast iron body with blue coloured cationic resin coating (VM models), incorporating either plastic or stainless-steel impellers (see model), stainless steel sleeve, EPDM gaskets and seals. Maximum working pressure 10.0 bar / 16.0 bar (see models). Cold water use only.
Range of shower outlets, (brass bodies - various finishes), incorporating ball joints, EPDM ‘O’-rings and NBR rubber seals. Maximum operating temperature 60°C
Range of wall or ceiling mounted shower outlets with plastic bodies (various finishes) and brass shower arms (various finishes, incorporating EPDM O-rings and plastic flow regulators. Maximum operating temperature 60°C.
Range of chrome plated plastic bodied or brass bodied (28 489 xxx model) overhead shower outlets. The 27 405 xxx model is supplied with a ceiling mounted shower arm and the 27 424 xxx models with a wall mounted shower arm, both are chromium plated brass. All shower outlets incorporate a combined EPDM washer and plastic strainer on the inlet. Maximum operating temperature 70°C.
Range of wall mounted shower arms, (brass bodies - various finishes) incorporating EPDM washers. Maximum operating temperature 60°C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
A Range of drain valves with bronze bodies incorporating brass bonnets, stems and baffles with EPDM seats and O’-rings. The products incorporate a rising spindle operating mechanism. Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of draining taps with DZR brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of (grey or black) nylon or polyethylene braided flexible hose assemblies comprising of a multi-layered hose with a black HDPE outer layer and green PEX inner layer. End connections can incorporate an ‘O’-ring, a washer and/or a V-ring. Washers and ‘O’-rings are EPDM, the V-ring is silicone. Maximum operating temperature 60°C.
Multi-layer PVC shower hoses with silver coating, brass end connections, EPDM gasket and NBR ‘O’-ring. Open outlet use only. Maximum operating temperature 65°C
Adaptor assembly consisting of a brass fitting with EPDM washer and PEX hose. Open outlet use only Maximum operating temperature 60°C
Range of PVC hoses incorporating EPDM washers. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of PVC, Stainless Steel or Nylon shower hoses with PVC or EPDM inner hoses. Maximum operating temperature 65°C or 80°C (See Models) Open Outlet Use Only
Stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals. Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless-steel braided EPDM lined flexible hoses, incorporating EPDM gaskets. Some models incorporate an isolation valve. Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of stainless-steel or nylon braided PEX lined hoses, incorporating EPDM O-ring or gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided TPSiV lined flexible hose assemblies incorporating EPDM O-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of chromium plated interlocked, PEX lined shower hoses with EPDM rubber gaskets. Maximum operating pressure: 6.0 bar. Maximum operating temperature 85°C.
Range of air venting valves with a stainless-steel bodies and springs, plastic float and EPDM ‘O’-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 80.0°C.
Range of air release valves with plastic bodies, EPDM ‘O’ rings and polypropylene floats. Maximum working pressure 16.0 bar. Cold water use only.
Range of T-type thermostatic mixing valves with chrome plated DZR brass bodies and EPDM ‘O’-rings incorporating a thermostatic cartridge controlling the temperature. Each inlet incorporates a stainless steel strainer. The inlets of the 252714 and 252713 models incorporate a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 10.0 bar. Maximum operating temperature of 85°C.
‘Rada’ electronically controlled thermostatic blending valve, with a stainless-steel body, EPDM ‘o’ rings and seals. Maximum working pressure; 13.8 Bar. Maximum operating temperature 85°C.
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer, lug type and double flanged butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron discs and an EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and EPDM rubber seat. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of butterfly valves with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. Gearbox and handwheel Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of wafer, lugged and flanged butterfly valves with blue epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. UWBV-4, LWBV-V4 & FBV-4 models incorporate a hand wheel operating members and UWBV-34, LWBV-3V4 & FBV-34 incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of butterfly valves with ductile iron bodies, nylon coated or stainless-steel disc with an EPDM seal. Maximum working pressure from 16.0 Bar to 20.0 Bar Cold water use only.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Ranges of wafer, lugged or double flanged butterfly valves with blue epoxy coated, ductile iron bodies and either epoxy coated ductile iron or stainless steel discs and EPDM seats and ‘O’- rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure reducing valves with nickel plated DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 0.5 and 6.0 bar. The products are supplied with an optional pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum operating temperature 80°C.
Range of pressure relief valves with plastic bodies and EPDM diaphragms and ‘O’-rings, Factory pre-set at 3.0 bar. Maximum operating temperature 110°C.
Range of angled pressure relief valves (pre-set at various pressures) with DZR brass bodies and EPDM diaphragms. Maximum working pressure: SEE MODELS Maximum operating temperature 99.0°C
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10130420) Maximum working pressure 25.0 bar (model 10130379) Maximum working pressure 40.0 bar (models 10130277 & 10130345) Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline or angled servicing valves incorporating a white (-W and -01 suffix models) or grey (all other models) plastic body, chrome plated brass ball, EPDM washers and EPDM ‘O’-rings. The products are either lever operated (-H and -01 suffix models) or screwdriver operated (all other models). Push fit connections are for use with copper pipe (manufactured to EN 1057), John Guest BPEX pipe or PEX barrier pipe (manufactured to BS EN 7291-3) and John Guest BPB or polybutylene barrier pipe (manufactured to BS EN 7291-2). Maximum working pressure and operating temperature: 13.24 bar @ 20°C, 6.0 bar @ 65°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 3233 model has a rising spindle, the 3243 model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM, EPDM gasket and NBR O rings. The valves incorporate a non-rising spindle headwork. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges and non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with blue epoxy coated cast iron bodies and EPDM coated cast iron wedges, operated via non-rising spindle. Maximum working pressure 10.0 bar and 16.0 bar (dependent on flange drilling pattern). Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of screw down stop valves with brass bodies, incorporating EPDM gaskets. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
‘Ballorex’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'6EP1862 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 60. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EPDM 9611 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radii sizes between 0.48mm & 2.0mm. For use with water up to 85°C.
'80-ADX-EPW/TN NR.3'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 0.75mm. For use with water up to 85°C.
'TJJH-EPDM gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 70. Tested in-radius size 1.2mm. Between April 2024 and March 2025, the gasket was for use with water up to 23°C. Between April 2025 and April 2029, the gasket is for use with water up to 65°C.
'FFE7018F'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'557WE, 557WG & 557WM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60, 70 & 90. Tested in-radius size 0.85mm. For use with water up to 85°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'OR 70 EPDM 335 DW 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. ‘O’ rings with an in-radius size between 0.5mm & 1.77mm are for use with water up to 85°C. When processing an application for WRAS Product Approval the in-radius tolerance may not be applied to these sizes. ‘O’ rings with an in-radius size of 3.5mm were added to the approval in December 2025 and are for use with water up to 23°C. When processing an application for WRAS Product Approval the in-radius tolerance may be applied to these sizes.
'TIMO 3-70 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
‘TIMO 3-60 ‘O’ rings and gaskets’. Black coloured, injection moulded EPDM ‘O’ rings and gaskets. Shore hardness 60. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
'EP801324C'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'C12251'. Black coloured, compression moulded EPDM material. Shore hardness 77. Tested in-radius size 10.0mm. For use with water up to 60°C.
'CH EP 160 DM'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM BW 5950 J 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 2.0mm. For use with water up to 65°C.
'KX-1'. Black coloured, compression moulded, EPDM rubber sheet material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5858'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EPDM70-BH'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DQ-EPDM75'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 85°C.
'HT5557-20'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EP8008'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. tested in-radius size 1.0mm. For use with water up to 85°C.
'LX-EP701P'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EZ Valve EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'SE-718PF'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AquaFlex T 5821'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EDXX 74'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.5mm. For use with water up to 85°C.
'70EP505P'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
Spring loaded in-line check valve cartridges for insertion into pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Range of quarter turn ceramic disc or non-rising spindle headworks (see models) with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Integrated magnetic headwork with EPDM ‘O’-rings and gaskets for insertion into specifically dimensioned bores. The headwork is operated by a push-button that moves a magnetic pillar, which in turn attracts the magnetic seal ring causing the valve to open, when the button is released the magnetic pillar travels back and the seal ring returns and the valve closes. The product incorporates a plastic flow regulator. Maximum working pressure 6.0 bar. Maximum operating temperature 85°C.
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies, brass bodies with (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with an approved installation kit consisting of stainless-steel braided EPDM lined flexible hose assemblies with ½” BSP (F) captive nut end connections with 15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) verified by test that also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies, brass bodies with (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with an approved installation kit consisting of stainless-steel braided EPDM lined flexible hose assemblies with ½” BSP (F) captive nut end connections with 15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) verified by test that also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a surface mounting kit incorporating EPDM lined flexible hose assemblies with ½” captive nut and 15mm compression isolation valves that incorporate single check valve assembly (suitable for backflow protection against fluid category 2). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of expansion vessels with epoxy coated steel bodies and EPDM diaphragms. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Maximum operating temperature 70°C or 100°C (please refer to model).
Filling loop assembly, incorporating a stainless-steel braided EPDM lined flexible hose assembly, an isolation valve (DZR brass body) and a combined isolation valve and non-verifiable double check valve assembly (DZR brass body) which incorporates 2 check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of medical sterilised water filter cartridges with plastic bodies and EPDM ‘O’-Rings. Models SMTFW-SLSS / SMTFD-SLSS incorporate a check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum Working Temperature: 50°C.
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PFD press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of fohn stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with FOHN stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of “JRG Sanipex MT” compression fittings with EPDM ‘O’-rings for use with “JRG Sanipex MT ECO” multilayer pipes (PE-RT II/Al/PE-RT II). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘Tectite 316’ range of push-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with stainless steel tube (Grade 316 manufactured to EN 10312). Maximum working pressure: Fittings 15mm to 28mm 10.0 bar. Fittings 35mm to 54mm 6.0 bar. Maximum operating temperature 90°C.
Range of ‘B’ Press XL copper crimped fittings with EPDM ‘O’-rings for use with copper pipe to BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
B Profile range of 316L & 304 stainless steel press fittings with EPDM ‘O’-rings for use with stainless steel pipe manufactured to EN 10312, for both above and underground use. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Silicon Bronze bodies Press Fittings with EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Copper press-fit fittings with copper with EPDM `O`-rings. For use with copper pipe manufactured in accordance with BS EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘POD’ range of indirect and direct heat interface units providing space heating and instantaneous hot water. The heat transfer is generated via plate heat exchangers. The domestic hot water (DHW) circuit incorporates an adjustable temperature mixing valve. The indirect models incorporate an expansion vessel (on the CW inlet of the DHW circuit) and a pressure relief valve set at 3.0 bar (on the space heating circuit). The indirect models only are supplied with a temporary filling loop, which comprises of a stainless steel braided EPDM lined flexible hose assembly and a lever operated spherical valve for connection to the primary circuit. The angled cold water inlet incorporates an isolation valve and a branch to connect to the filling loop, which includes a double check valve assembly (verified by test, suitable for backflow protection against Fluid Category 3). Maximum working pressure for indirect units: Primary circuit: 16.0 bar. Space heating: 2.5 bar. Secondary circuit (DHW): 10.0 bar. Maximum working pressure for direct units: Primary circuit: 10.0 bar. Space heating: 10.0 bar. Secondary circuit (DHW): 10.0 bar. Maximum operating temperature for domestic hot water 65°C. Maximum operating temperature for central heating and primary circuit 85°C.
Range of water meters with cast iron bodies (blue epoxy coating) and EPDM ‘O’ rings. Maximum working pressure 16.0 Bar Maximum operating temperature 23.0°C
Range of water meters with either cast iron (blue epoxy coated) or stainless-steel bodies, transducers and EPDM rubber O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 50.0°C.
Range of water meters with either cast iron (blue epoxy coated) or stainless-steel bodies, transducers and EPDM rubber O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 50.0°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of ‘Thermowatt’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Surface mounting kit for a mono block sink mixer with stainless steel braided EPDM lined flexible hose assemblies with ½” BSP captive nut end connections. The product is supplied with a 15x15mm compression isolation valves that incorporate single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of positive displacement diaphragm pumps with plastic bodies, EPDM ‘O’-rings and TPE diaphragm. The product incorporates an integral bypass relief valve. For use with John Guest LLDPE Pipe. Maximum working pressure 12.0 Bar. Maximum operating temperature 40.0°C.
Range of single stage booster pumps incorporating a flow switch. Model 46349 CH 12-14 B is supplied with a pressure vessel and incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with a strainer and stainless-steel braided EPDM lined flexible connection hoses. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of overhead shower outlets (chromium plated ABS plastic bodies). Incorporating a combined EPDM washer and stainless-steel strainer on the inlet. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets (chromium plated ABS plastic bodies). Incorporating a combined EPDM washer and stainless-steel strainer on the inlet (all other models). Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower kits comprising of ABS bodied shower handsets and PVC multi-layer hoses incorporating EPDM ‘O’-rings. Supplied with riser rail. Available in various finishes. Maximum operating temperature 60°C
Overhead shower outlet with a stainless-steel body and EPDM seals. Maximum operating temperature: 85°C.
Range of overhead shower outlets, (chrome plated) ABS material incorporating a swivel connection, incorporates a stainless-steel strainer with an EPDM gasket. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of chrome plated shower kits consisting of shower hoses with EPDM washers incorporating stainless steel strainers at the captive nut, handsets and riser rail assemblies. Maximum operating temperature 60°C.
Overhead ceiling or wall mounted (depending on shower arm) shower outlet with chrome plated plastic body, EPDM o-rings and a plastic flow restrictor at the ball joint. Maximum working pressure: Open outlet. Maximum operating temperature: 60°C.
Range of overhead shower outlets, (brass bodies - various finishes. The inlets incorporate combined EPDM washers and stainless-steel strainers. Open outlet use only Maximum operating temperature 60°C
Wall mounted shower set comprising of an inlet connection, shower handset (brass bodies, various finishes), shower holder and EPDM lined shower hose. Maximum operating temperature 85⁰C.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of drain valves with a brass bodies, spindle and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of plastic shower hoses with a Black PVC inner liner, NBR O-ring and EPDM gaskets available with either brass or stainless-steel ferrules and barbs. Maximum operating temperature: 65⁰ C.
Range of stainless-steel braided TPS lined flexible hose assemblies incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves Push-fit fittings for use with: Copper Pipes manufactured in accordance with BS EN 1057 PB pipes manufactured in accordance with BS 7291-2 PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure 12.0 bar. Maximum operating temperature 65°C.
‘Qualflex Excel’ range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves. Push-fit fittings for use for with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.
Flexible safety hose assembly with PVC inner hose and corrugated outer cover incorporating EPDM gaskets. The inlet of the hose incorporates a plastic strainer. The hose is fitted with an integral device consisting of a water sensitive material which expands when in contact and is intended to stop the flow of water (please note that this function has not been verified by test). Maximum working pressure: 10.0 Bar. Maximum operating temperature: 60.0°C.
Inlet hose consisting of a EPDM inner hose layer and corrugated outer cover. The hose is fitted with an integral device consisting of a water sensitive material which expands when in contact with water. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of TPE shower hoses (various finishes) with EPDM seals. Open outlet use only. Maximum operating temperature 60.0°C
Range of stainless-steel interlocked shower hoses and shower hose extension pieces (smaller length versions) incorporating PE/EPDM and PEX inner tube materials. Available with various surface finishes and end connectors. For further details see model section. Maximum working pressure open outlet use. Maximum operating temperature 85.0°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies. Compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of stainless steel or nylon braided EPDM lined flexible hose assemblies with various brass end connections. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10 Bar. Maximum operating temperature 70°C.
Nylon and stainless-steel braided EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of stainless steel braided hoses with EPDM liner and NBR or fibre gaskets. DN13 and DN19 Maximum working pressure 10 bar. Maximum operating temperature 65°C. DN25 Maximum working pressure 10 bar. Cold water use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. SCFA models incorporate a spherical valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of automatic air venting valves with plastic bodies and EPDM ‘O’-rings. Maximum working pressure 6.0 bar. Maximum operating temperature 99°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of single/double orifice air venting valves with blue epoxy coated ductile iron bodies, and a stainless-steel float ball. Incorporating EPDM washers. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of T-type thermostatic blending valves with nickel plated brass bodies and EPDM ‘O’-rings. The inlet and outlet incorporate an approved check valve cartridge ((verified by test - suitable for backflow protection against fluid category 2). Models with compression ends are to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated butterfly valves with stainless steel discs and EPDM seal. Maximum operating pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating), stainless steel disc and EPDM seat. The valves are operated by a lever mechanism. Maximum working pressure 20.0 bar. Cold water use only.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel (2302/2502 models) or chrome plated iron disc 2304/2504 models). Products are either handwheel (H) or gear (G) operated (see models). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ranges of wafer or lugged butterfly valves with blue epoxy coated ductile iron bodies incorporating EPDM seat. The valves can be supplied with either Stainless steel, Nickel or blue epoxy coated ductile iron discs. Maximum working pressure: 16.0bar. Maximum operating temperature: 85°C.
Manual diverter with a brass body incorporating EPDM ‘O’-rings and seals. Maximum working pressure 6.0 Bar. Maximum operating temperature 70.0°C
Concealed three-way diverter valve with various body finishes and EPDM ‘O’-rings. Also supplied with various trim sets. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Range of pilot operated flow control valves with blue epoxy coated, ductile iron bodies and EPDM ‘O’-rings. Auxiliary components include stainless steel tube with fittings, a stainless-steel strainer and spherical valves. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C or cold water use only – see data plate marking.
Range of pilot operated flow control valves with (blue or red/brown) epoxy coated stainless steel bodies and EPDM ‘O’-rings. Auxiliary components include stainless steel tube with fittings, a strainer, spherical valves, needle valve and restriction orifice. Maximum working pressure 16.0 Bar Maximum operating temperature 65 °C.
Range of eccentric plug valves with blue epoxy coated ductile iron bodies, PTFE washers a stainless steel plug which is fully encapsulated with EPDM. Maximum working pressure 16 Bar. Maximum operating temperature 80°C.
Range of adjustable, in-line pressure reducing valves with blue epoxy coated, cast iron bodies. SP models: maximum supply pressure 25.0 bar, outlet pressure range 1.5 to 7.0 bar. HP models: maximum supply pressure 25.0 bar, outlet pressure range 3.0 to 12.0 bar. LP models: maximum supply pressure 8.0 bar, outlet pressure range 0.5 to 3.0 bar. Maximum operating temperature 60°C.
Range of adjustable pressure reducing valves with stainless steel bodies and EPDM ‘O’-rings and diaphragm. These products are available with the following adjustable outlet pressures: between 1.0 and 6.0 bar (model REF-150-S is between 1.2 and 6 bar), between 4.0 and 10.0 bar or between 8.0 and 13.0 bar. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of adjustable, in-line pressure reducing valves with DZR brass bodies, incorporating a spring loaded EPDM diaphragm and a gauge port. The products incorporate an integral stainless steel strainer. The outlet pressure range is adjustable between 1.0 and 6.0 bar. Maximum inlet supply pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of pressure relief valves with DZR brass bodies incorporating EPDM diaphragms. The valves are pre-set as follows: 311560, 312469, 312461ITH, 311461CTS,531661 CST models: 6.0 bar, 312471 CST model: 7.0 bar, 312020 CST model: 10.0 bar. Maximum operating temperature 99°C.
Range of latching or non-latching normally closed solenoid valves with brass bodies. Maximum working pressure 10.0 Bar to 15.0 Bar (see models). Maximum operating temperature 90.0°C.
Range of normally open and normally closed solenoid valves with brass bodies & EPDM diaphragms. Maximum working pressure 5.0 bar. Cold water use only.
In-line spherical valve with a chrom eplasted DZR brass body, brass ball and EPDM ‘O’-rings, incorporating a single check valve cartridge (verified by test, suitable for fluid catergory 2) with a lever operating member. To be used with copper pipe manufactured to EN1057. verified Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of electronically controlled spherical valves with a smart water leakage shut off, incorporating a ceramic pressure sensor, stainless steel ball and EPDM O-rings. Maximum working pressure; 16 Bar Maximum operating temperature 85°C
Series of brass valves with EPDM o-ring isolation valves with M profile press crimped connections to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of resilient seated gate valves with a blue epoxy coated ductile iron body and a ductile iron gate/wedge which is fully encapsulated with EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 80.0°C.
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models HY-002A & HY-002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
‘BOSS VENTURI’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Thermostatic circulation valves incorporating DZR brass bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 90°C.
STAD range of balancing valves with brass bodies, PTFE sliding washer and EPDM O-rings. Models are available with or without a drain port. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'E7108 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'E7108 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'EP11/7/4 BLK'. Black coloured, injection moulded EPDM rubber `O` rings & gaskets. Shore hardness 70. The ‘O’-rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 1.4mm. For use with water up to 85°C.
'EPDM B1-4710'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.55mm. For use with water up to 85°C.
'VULCAN VEE4 Bellow & Boot'. Black coloured, compression moulded EPDM bellows and boot components. Shore hardness 70. The bellows has an in-radius size of 3.0mm and the boot has an in-radius size of 0.9mm. For use with water up to 85°C.
'E 71 65 003'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.5mm. For use with water up to 85°C.
'EP703904 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EP703904 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'EP11/8/3 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP701443C 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.75mm. For use with water up to 85°C.
‘E27 EPDM moulded parts'. Black coloured, injection moulded EPDM seals. Shore hardness 75. Tested in-radius size between 0.8mm & 4.0mm. For use with water up to 85°C.
‘EPDM EV2’. Black coloured, injection moulded EPDM materials. Shore hardness 75A. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'OLDAL 460'. Black coloured, injection moulded EPDM material. Shore hardness 50. Tested in-radius size 1.2mm. For use with water up to 85°C.
'E7083AA'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E8083AA'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CH EP 172 DM'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SE-808PF'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7037K'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Pango2023'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TRA-7073'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM70(E7-512K)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'LCKB70'. Black coloured, compression moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.3mm. For use with water up to 85°C.
'E13970'. Black coloured, injection moulded EPDM material. Shore hardness 65. Tested in-radius size 1.3mm. For use with water up to 23°C.
'F3352'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Spring loaded, resilient trim, in-line check valve cartridge with NBR & EPDM ‘O’-rings, plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 8.6 Bar. Maximum operating temperature 60°C.
Range of aerators with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 65°C Open outlet use only
Range of non-rising spindle headworks with a brass body and EPDM ‘O’-rings. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85.0°C.
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic cartridge headworks with brass bodies and EPDM gaskets and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Thermostatic cartridge incorporating a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and metal backnuts. The spout outlets incorporate a plastic aerator. The headwork is connected to the spout via interconnecting stainless steel braided, EPDM lined flexible hoses. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Three-hole, single outlet (swivel) combination tap assembly (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks with single lever operating members. The products are also supplied with stainless steel braided EPDM lined flexible hose assemblies, intended for use between the side body valves and spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Ranges of cylindrical or tubular expansion vessels with epoxy coated or uncoated steel bodies and either Butyl or EPDM membranes. Maximum working pressure of Tube models is 8.0 bar. All other models have a maximum working pressure of 10.0 bar. Maximum operating temperature 99°C.
Filling loop assembly, incorporating a stainless-steel braided EPDM lined flexible hose assembly, an isolation valve (DZR brass body) and a combined isolation valve and non-verifiable double check valve assembly (DZR brass body) which incorporates 2 check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Filling loop assembly consisting of an in-line isolation valve, an in-line double check valve assembly which incorporates an isolation valve (suitable for back flow protection against fluid category 3) and a stainless steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “SOUTH PRESS” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of copper press fittings with EPDM ‘O’-rings for use with EN1057 copper tube. The joints are achieved by means of a press tool. For above and below ground use (sizes 12mm-54mm only. 66.7mm, 76.1mm, 88.9mm & 108mm for above ground use only) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PCC type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN 1057. Maximum working pressure; 16.0 Bar. Maximum operating temperature 85oC
Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
“<A> Press Copper M Profile” series press fittings with a copper body and EPDM ‘O’-rings, for use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of system 2000 of flange adaptors and connectors with ductile iron bodies (Blue Epoxy Coated) incorporating EPDM seals. For use with PE pipe manufactured to En 12201 & PVC Pipe manufactured to DIN 8062. Maximum working pressure: 16.0Bar Cold water use only.
Jet range of water meters with brass blue epoxy coated bodies and EPDM rubber ‘O’-rings. Maximum working pressure16.0 bar. Maximum operating temperature 85°C.
Range of water meters with brass bodies and EPDM ‘O’-rings and plastic strainer on inlet. Maximum working pressure 16 bar. Cold water use only.
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Bias chamber incorporating an EPDM diaphragm and ‘O’-ring with a brass body. Maximum working pressure 35.0 bar. Cold water use only.
Range of two, three or four pump booster sets, with vertical multistage pumps comprising of pressure vessels, stainless steel manifolds, pressure gauges, spherical valves and EPDM O-rings. Maximum working pressure - 10.0 bar. Max operating temperature - Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of vertical (CVM) or horizontal (CHM) multistage pumps with stainless-steel bodies and stainless-steel impellers, intermediate chambers, shaft and outer sleeve and EPDM seals. Maximum working pressure: 25 Bar. Maximum working temperature: 23°C.
‘UPM10’ and ‘UPM20’ range of circulator pumps with a stainless-steel body, plastic impellor and EPDM ‘O’-rings. The product is supplied with EPDM gaskets for the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of shower outlets with ABS plastic bodies and NBR and EPDM O-rings. The inlets incorporate stainless steel strainers. Maximum working pressure: Open Outlet use only. Maximum operating temperature 75°C
Range of wall mounted shower heads incorporating (chromium plated brass body) and EPDM ‘O’-rings. Maximum operating temperature 60°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless-steel or nylon braided hoses with a PEX inner hose. The hoses are either supplied with silicone or EPDM 'O'-rings. Some hoses incorporate a isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel or nylon braided hoses with a PEX inner hose. The hoses are supplied with either silicone or EPDM 'O'-rings. Some hoses incorporate a isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of PVC plastic shower hoses with black and silver corrugated outer, with EPDM washers. Maximum operating temperature 60°C.
Range of stainless steel braided hoses, incorporating a dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. The SOG1212XXX(GLF)CS model incorporates an isolation valve. The models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided PEX lined flexible hose assemblies with EPDM washers and/or ‘O’-rings, and brass end connections. The 15mm compression connection incorporates an isolation valve. The models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of nylon braided PEX lined flexible hose assemblies with EPDM washers and ‘O’-rings with a variety of end connections. Maximum operating temperature 65.0°C
Range of PVC shower hoses with EPDM O-rings. Maximum operating temperature 65°C. Open outlet use only.
Range of EPDM hoses with either nylon or stainless-steel braiding, with or without a PVC sheath. Some models incorporate isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of elastomeric shower hoses with EPDM lining and ‘O’-rings. The product incorporates a flow restrictor. Maximum operating temperature 60.0°C Open outlet use only
Range of stainless-steel braided flexible hose assemblies incorporating EPDM inner and plastic (BFSFH12-EE80/150) or brass (BFSFH19-EE60) captive nut end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided, EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of stainless steel interlocked shower hoses with EPDM O-rings. Maximum operating temperature 65°C. Open outlet use only.
Range of stainless steel or black nylon braided EPDM lined flexible hose assemblies with EPDM washers and/or ‘O’-rings, and brass end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
‘FlexPlus’ range of EPDM lined stainless steel braided flexible hose assemblies with brass end connections. Maximum working pressure: 10 Bar. Maximum operating temperature: 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of stainless steel inter-locked shower hoses incorporating an EPDM inner liner and EPDM gaskets. Maximum operating temperature 85°C.
White and grey nylon EPDM lined braided hose. Maximum working pressure 10 Bar. Maximum operating temperature 90°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). For use with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of EPDM lined hoses with grey PVC outer layer. Maximum working pressure: 16 bar. Maximum working temperature: 60°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of flanged butterfly valves incorporating blue epoxy coated ductile iron bodies and discs with EPDM rubber seats. Models incorporate hand wheel operating members. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged butterfly valves incorporating blue epoxy coated ductile iron bodies and discs with EPDM rubber seats. Models incorporate hand wheel operating members. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel or chrome plated iron disc. Products are either handwheel or gear operated. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer, lugged and flanged butterfly valves with blue epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. E71X4, E71XLV4 & E41X4 models incorporate a hand wheel operating members and E371X4, E371XLV4 & E341X4 incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel (VA2502 & VA2502G models) or chrome plated iron disc (VA2504 & VA2504G models). Products are either handwheel (H) or gear (G) operated (see models). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ranges of butterfly valves with ductile iron bodies (blue epoxy coating), stainless steel or ductile iron (blue epoxy coating) disc and EPDM seats. The products are supplied with a rotating wheel /or gear box operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Double flanged butterfly valve with blue epoxy coated body, grey epoxy coated plate, EPDM seals & handwheel operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of wafer and lug type butterfly valves incorporating blue epoxy coated ductile iron bodies, either stainless steel (SS316/SS304) or epoxy coated ductile iron discs and EPDM seat. The valves are either handwheel and gear operated (Models D371X and DL371X) or lever operated (Models D71X and DL71X). Maximum working pressure 16.0 bar Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies & wedges and EPDM sealing gasket. The closing mechanism is controlled by a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85˚C.
Range of lugged, flanged and wafer butterfly valves with ductile iron blue epoxy coated bodies. The valves are operated by either a lever or gearbox (see models). Maximum working pressure 16.0bar. Maximum operating temperature 85°C.
Range of lugged, semi lugged, wafer type or U shaped (see models) butterfly valves with a blue epoxy coated cast iron body, EPDM seat and either a stainless steel, bronze, EUROKOTE - EBONITE or blue epoxy coated iron disc (see models). Maximum working pressure 6.0, 10.0 or 25.0 Bar (See models) Maximum operating temperature 23.0 or 60.0°C (See models)
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with a wheel type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of control valves with nylon bodies, stainless steel springs, EPDM diaphragms and O-rings. Maximum working pressure 16 Bar. Cold water use only.
Range of regulating and shut-off valves with brass bodies and EPDM ‘O’-Rings. Maximum working pressure 16.0 Bar for BSP (M) and 25.0 bar for BSP (F). Maximum operating temperature 85.0°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
A range of spring loaded, resilient trim non-return valves with EPDM seat, blue epoxy coated cast-iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of in-line, manually adjustable pressure reducing valves with stainless-steel bodies and EPDM o-rings. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 25.0 Bar. Outlet pressures between 1.5 bar and 6.0 bar. Cold water use only.
Range of pre-set pressure relief valves incorporating DZR brass bodies and an EPDM diaphragms and PTFE washers. The valve is fitted with hand operated rotating easing gear. Maximum working – see model. Maximum operating temperature 85°C
Range of latching (LV), proportional (PV), servo (SV), pilot (EV) solenoid valves with natural (appear white), plastic bodies. Valves with black coloured plastic bodies (incorporating a biocide) were added to the approval in January 2026. Pushfit models are for use with John Guest LLDPE and DMFIT LLDPE pipes. The inlets and outlets of all models are available with plastic flow regulators or plastic or copper strainers. All valves have a maximum working pressure of 10.0 bar. The bodies of valves with a silicone diaphragm are marked with an ‘S’ at the end of the model, e.g. ‘EV118/AS’ and have a maximum operating temperature 85°C. Valves with an EPDM diaphragm are for cold water use only and do not include this ‘S’ marking.
‘Instantor’ range of lever operated spherical valves with brass bodies and balls (chromium plated), incorporating PTFE seats, EPDM ‘o’ rings single lever handles (red or blue). For use with imperial Irish copper pipe (manufactured to IS EN 1057). Maximum working pressure 16 bar. Maximum operating temperature 85°C
A screwdriver operated spherical ball valve with brass body, chromium plated brass ball and EPDM O-ring. Maximum working pressure 5.5 bar. Maximum operating temperature 85oC.
Range of spherical valves with nickel plated brass bodies, chome plated brass balls and EPDM O-rings. Connection to be used with copper pipe EN1057. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever or screwdriver operated in-line spherical valves (chrome plated brass body), brass ball and EPDM seals. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models HY-002A & HY-002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of flanged ductile iron, blue epoxy coated gate valves with EPDM seats and hand wheel operating members. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 166 30 SERIES model has a rising spindle, the 166 33 SERIES model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 16.0 bar and a maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated) with EPDM coated ductile iron wedge and non-rising stem operated via a hand wheel operating member. Maximum working pressure: 16 bar. Maximum operating temperature: 80°C
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and ductile iron wedges encapsulated in EPDM. The valve is operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, non-rising spindles with handwheel operating member and a ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 bar. Cold water use only.
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models ZHR01B & ZHR01C incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models WVF‐002A & WVF‐002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The TCDIGVR16 & TCDIGVR25 models has a rising spindle, the TCDIGVN16 & TCDIGVN25 models has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedges and hand wheel operating members. Maximum working pressure: 16.0 Bar. Maximum operating temperature: 80°C.
Range of resilient seated gate valves incorporating ductile iron bodies with blue epoxy coated finish. The valves incorporate either rising (G series) or non-rising spindles (GNS series) and have an EPDM wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 80 °C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Gate valve with a blue epoxy coated ductile iron body and an EPDM lined disc, with a non-rising spindle operating mechanism. Maximum operating temperature: 80°C. Maximum working pressure: of 16.0bar.
Range of screw down stop valves with brass bodies, EPDM gaskets and PTFE washers. For use with copper pipe to EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 99°C.
Range of in line regulating valves with brass bodies, EPDM `O` rings. The valves incorporate a non-rising spindle headwork for temperature regulation. Max working pressure: See models. max operating temperature: See models.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'WRC EPDM 92645'. Black coloured EPDM liner manufactured by calendaring. Shore hardness 80 A. Tested in-radius size 0.5mm. For use with water up to 23°C.
'ME0940 'O' rings'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 5.0mm. For use with water up to 85°C.
'EPDM 70: Blaco_Water/Food-EE70’. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70 A. Tested in-radius size 0.75mm. For use with water up to 85°C.
'EPDM B1-4771'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'70 EP 101p'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'TIMO® 3NC-60 'O' rings and Gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 60. Tested in-radius size between 0.5mm & 2.67mm. For use with water up to 85°C.
'EP60/1 BLK 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 1.77mm. For use with water up to 85°C.
'51M7531 Diaphragm'. Black coloured, calendered, EPDM diaphragm. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 85°C.
'560AL Water Seal'. Black coloured, injection moulded EPDM seal. Shore hardness 70. Tested in-radius size 2.12mm. For use with water up to 23°C.
'E7331'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.8mm. For use with water up to 85°C.
'E8124'. Black coloured, injection moulded EPDM seal. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 85°C.
'E9053AA 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 90. Tested in-radii sizes between 0.4mm and 3.65mm. For use with water up to 85°C.
'EP50/1 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 50. Tested in-radius 1.7mm. For use with water up to 85°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'EP60/1 BLK'. Black coloured, compression moulded EPDM diaphragm seal. Shore hardness 60. Tested in-radius size 0.75mm. For use with water up to 85°C.
'558CM'. Black coloured, transfer moulded EPDM O-Ring. Shore hardness 60. Tested in-radius size 0.87mm. For use with water up to 85°C.
'ERA10-2 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'EPWL-60'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size between 1.25mm & 5.25mm. For use with water up to 23°C.
'ME0940/40 - 90'. Black coloured, injection moulded EPDM rubber material. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 3.0mm. For use with water up to 85°C.
'OLD ETP890 70N'. Black coloured, injection moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 85°C.
'EPWL-70'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size between 1.25mm & 5.25mm. For use with water up to 23°C.
'3E60B11P & 3E70B03P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'EP80R-01'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 50°C.
'798F'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 60°C.
'E50B01, E70B01 & E80B01'. Black coloured, compression moulded EPDM material. Shore hardness between 50, 70 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'CERULEAN EP 14 (KIEP14)'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'8550C'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP55 & EP70'. Black coloured, compression moulded EPDM materials. Shore hardness 55 & 70. Tested in-radii size 1.0mm. For use with water up to 70°C.
'51M6630'. Black coloured, injection moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'Precision782628 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
Five-hole, single outlet (fixed) combination tap assembly with brass bodies (various finishes), incorporating a quarter turn ceramic disc headworks to control the flow and a manual diverter to shower outlet both with single lever operating members. The spout outlet incorporates an aerator. The product is supplied with a pull out shower hose and shower handset, metal backnuts and stainless steel braided, EPDM lined interconnecting hoses. The handset also incorporates an approved single check valve, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of CA-b backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of CAb backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Filling link with manual or automatic tap. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim check valve cartridge with plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of spring loaded single check valve cartridges comprising of a POM body and cap, stainless steel spring and EPDM gasket and O-rings. Max working pressure 10 bar. Max operating temperature 85°C.
Shower flow regulator with a plastic body and EPDM O-rings incorporating a (chrome plated brass) housing Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies, EPDM gaskets and NBR O-rings. The products are for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of either half turn, quarter turn ceramic disc or non-rising spindle headworks with brass bodies and EPDM ‘O’ rings. For insertion into specifically dimensioned bores. Maximum working pressure 20.0 Bar Maximum operating temperature 90.0°C
Range of ceramic cartridge headworks with plastic bodies, incorporating EPDM seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar (D40P-17 & D40G-17) or 20.0 Bar (D25G-6) Maximum operating temperature 85.0°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 907015 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | C-plate | Aerator |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 193838 X XXX | VARIOUS | 1/2" BSP | 10 bar | 65 °C | PPI | Body | No | Ceramic cartridge | C Clamp | Aerator | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SAI BAS C | Chrome | M10 X 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Aerator | Pop Up |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| BQVEC BAS C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener | Click Type | |
| VT2 BASNW C | Chrome | 1/2" BSP Captive Nut | 5.0 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | Metal Backnuts | Flow Straightener | Click Type |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 193938 X XXX | VARIOUS | ½” BSP | 5.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 194828 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 181028 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 235038 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 223238 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | ON REAR OF BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass) bodies, incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Product supplied with a surface mounting kit comprising of Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” BSP captive nut end connections with 15x15mm compression isolation valves that incorporate single check valve cartridges, however, the complete assembly has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of chemical dosing equipment which incorporate self-closing valves within a plastic body with EPDM o-rings. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Only suitable for use with chemicals no greater than a FC3, additional backflow protection is required for chemicals greater than FC3. Maximum working pressure 9.0 bar. Maximum operating temperature 70ºC.
Range of filling loop assemblies, comprising of a stainless-steel braided EPDM lined hose, isolation valve (screwdriver or lever operated) with a DZR brass body and a double check valve incorporating a built-in isolation valve (screwdriver or lever operated) a DZR brass body. The F1400120012211 model has an approved double check valve incorporating a built-in isolation valve with a DZR brass body at each end of the filling loop. All valves are nickel plated. The products are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Filling loop assembly, comprising of a stainless-steel braided EPDM lined flexible hose assembly, an isolation valve (DZR brass body and ball) and a combined isolation valve and non-verifiable double check valve assembly (DZR brass body and ball) which incorporates 2 check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). The combined isolation valve and non-verifiable double check valve assembly incorporates a test point. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Cold water use only.
Range of press fittings (brass bodies - various finishes) with stainless steel press (Unipress MLCP ) collars and EPDM O-rings for use with “EA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for EHA adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless-steel (SS304 or SS316L) press fittings with EPDM ‘O’-rings for use with Dunshan stainless-steel (SS304 or SS316L) pipes. The DSU, DSMU and DSFU models also incorporate an EPDM gasket. Jointing is achieved via a crimping tool using a ‘M’ profile. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
‘LFLF10xx’ range of stainless steel press-fit fittings incorporating EPDM ‘O’-rings for use with ‘LFLP1001’ stainless-steel pipe. Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Instantor range of copper press fittings with an EPDM ‘O’-ring for use with copper pipe to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass press fittings with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings and EPDM washers. For use with stainless-steel pipe. Joints are achieved using a press fitting tool. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of stainless steel (SS316L) pressfit fittings with EPDM ‘O’-rings for use with stainless steel pipe (manufactured to EN10312). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of copper crimped fittings with EPDM ‘O’-rings for use with copper pipe manufactured to EN1057. For above and below ground use. Maximum working pressure 16 Bar. Maximum operating temperature 99°C.
Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of water meters with brass bodies, plastic turbines and EPDM washers. Inlets incorporate a plastic filter. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of water meters with either cast iron (blue epoxy coated) or stainless-steel bodies, transducers and EPDM rubber O-rings. Maximum working pressure 25.0 Bar. Maximum operating temperature 50.0°C.
Range of inline water meters with either brass or plastic bodies incorporating EPDM ‘O’-rings and can be provided with a plastic strainer. Maximum working pressure 16 Bar Cold water use.
Range of ultrasonic water meters with brass bodies, plastic transducers and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of Fastec® F13 and Fastec® F14 fittings for use with Fastec® manifold assemblies, incorporated with brass bodies and EPDM O-rings. To be used with copper pipe complying with BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Water hammer arrestor with brass body and EPDM ‘O’ ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of ‘SureCal’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O` rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Please refer to model for maximum operating pressure. Maximum operating temperature 65°C.
Range of single and twin ended shower booster pumps with plastic bodies and plastic impellers. The inlets/outlets incorporate stainless steel braided EPDM lined flexible hose assemblies with isolation valves and stainless-steel strainers. The outlets incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. The Universal Twin models incorporate an expansion vessel. Maximum working pressure 1.5, 1.8, 2.0, 2.5, 2.6, 3.0 Bar (see model for more details). Maximum operating temperature: 60.0°C.
Range of overhead shower outlets (ABS bodies - various finishes, see model), incorporating NBR and EPDM ‘O’ rings that incorporate stainless-steel mesh strainers.
Non-metallic materials and components comply with BS6920 at 70°C
Shower kit consisting of a plastic bodied shower handset (matt black), riser rail and PVC lined multi-layered shower hose with brass connections, EPDM 'O'-rings and strainer. Maximum operating temperature 60°C.
Drain off cock with a DZR brass body, non-rising spindle headwork and EPDM seals and washers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Dual layered, extruded PVC hoses incorporating EPDM washers. Maximum working pressure 10.0 bar. Cold water use only.
Range of stainless steel braided, nylon braided, double locked (metal outer) or reinforced (see model), PEX/HTRPE lined flexible hose assemblies with EPDM washers and O rings. Available with a variety of finishes or end connections (see model). Maximum operating temperature 85°C.
Range of PVC plastic shower hoses with black and silver corrugated outer, with EPDM washers. Maximum operating temperature 60°C.
Multi-layer PVC shower hoses with silver coating, brass end connections, EPDM gasket and NBR ‘O’-ring. Open outlet use only. Maximum operating temperature 65°C
Range of stainless steel or polymeric braided, PERT and LDPE lined flexible hose assemblies with EPDM O-rings. Available with a variety of end connections for each size and model. Compression connection to be used with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.
Stainless steel braided hoses, incorporating a dual layered hose consisting of a clear PE liner and black coloured EPDM outer layer. The Click Seal 1TF300UKCSV model incorporates an isolation valve. The compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.
Range of EPDM or PVC lined, interlocked stainless-steel shower hoses. Open outlet use only. Hoses with an EPDM liner have a maximum operating temperature of 85°C. Hoses with an PVC liner have a maximum operating temperature of 65°C.
Range of stainless steel braided EPDM lined flexible hose assemblies. The captive nut and M15x1 end connections incorporate a washer. The M8x1, M10x1 and M12x1 end connections incorporate an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided flexible hose assemblies incorporating EPDM inner and plastic (BFSFH12-EE80/150) or brass (BFSFH19-EE60) captive nut end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel braided EPDM lined flexible hose assembly with EPDM washers. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PVC outer layer shower hoses with a PVC internal layer and EPDM washers. Open outlet use only. Maximum operating temperature:60C
Stainless steel braided hose incorporating an EPDM liner and NBR ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of PVC outer layer shower hoses with a PVC internal layer and EPDM washers. Open outlet use only. Maximum operating temperature:60C
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections. Maximum working pressure: 6.0 bar @ 65°C Maximum working pressure: 12.0 bar @ 20°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
temperature and pressure relief valve set at 7.0 bar@90˚C. A safety kit (manifold) consisting of a check valve cartridge (verified by test, suitable for backflow protection against Fluid category 2) strainer, an expansion relief valve set at 6.0 bar and pressure reducing valve set at 3.0 bar. A tundish, expansion vessel and a filling loop assembly, incorporating a stainless steel braided EPDM lined flexible hose, brass bodied isolation valve and a DZR brass non-verifiable double check valve assembly that incorporates an isolation valve. Maximum working pressures: Secondary circuit 5.5 bar. Primary circuit 3.0 bar Maximum operating temperature 90.0°C
Mitsubishi “ECODAN” EHPT20X– MEHEW indirectly heated stainless-steel storage cylinder. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar and 90˚C. The product is supplied with a safety kit (manifold) consisting of a single check valve cartridge (verified by test, suitable for backflow protection against Fluid Category 2), strainer, a pressure relief valve set at 6.0 bar and a pressure reducing valve set at 3.5 bar. The product is also supplied with a tundish, an expansion vessel and a filling loop assembly, consisting of a stainless-steel braided EPDM lined flexible hose, a lever operated brass spherical valve and a DZR brass double check valve assembly (suitable for backflow protection against Fluid Category 3) that incorporates a lever operated spherical valve Maximum working pressures: Secondary: 5.5 Bar Primary/CH circuit: 2.5 Bar Maximum operating temperature 75.0°C
Range of lever operated butterfly valves with blue epoxy coated cast iron bodies, stainless steel discs and EPDM ‘O’ rings and seals. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of eccentric lugged or wafer type butterfly valves with stainless teel or blue epoxy coated bodies and stainless steel or epoxy coated ductile iron discs, incorporating EPDM or PTFE seats (see models). Max working pressure: 10.0 Bar, 16.0 Bar or 20.0 Bar (see models). Max operating temperature 80°C or 99°C (see models).
Range of butterfly valves with blue epoxy coated ductile iron bodies, coated ductile iron or stainless-steel discs & EPDM sealing ring. The closing mechanism can be controlled by single lever or a handwheel. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of butterfly valves with ductile iron bodies (blue epoxy coated) and discs. The seats incorporate EPDM seals, and the products are operated via a hand wheel. Maximum working pressure: 16.0 Bar Maximum operating temperature: 60°C
Range of wafer and fully lugged butterfly valves (gear or handwheel operation) with a cast iron body (blue epoxy coated), EPDM seat and stainless steel disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves (gear or handwheel operation) with a cast iron body and disc (blue epoxy coated), EPDM seat. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated butterfly valves, incorporating blue epoxy coated ductile iron bodies and discs, with EPDM seats. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C.
Range of wafer, lug or flanged butterfly valves (lever or handwheel operation) with cast iron or stainless steel bodies (blue epoxy coated), EPDM seat and stainless-steel disc. Maximum working pressure 16.0 Bar Maximum operating temperature 90.0 to 100.0°C
Range of lever operated butterfly valves incorporating fusion bonded Epoxy coated ductile iron bodies, with stainless steel discs and end faces and EPDM seat. For use with Stainless steel pipe manufactured to EN 10217-7 (or Equivalent). For above and Below ground. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged (see models) butterfly valves incorporating plastic bodies & discs and an EPDM seat. Maximum working pressure 16.0 bar Maximum operating temperature 100°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of black nylon coated cast iron equilibrium float operated valves with EPDM seals. Maximum working pressure 10.0 Bar Maximum operating temperature 23.0°C
Range of pressure reducing valves with DZR brass bodies, internal stainless steel filter, EPDM ‘O’-rings and diaphragm. Adjustable outlet pressures between 1.0 and 6.0 bar or 1.0 and 12.0 bar (see model). Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 80°C.
Range of pre-set pressure relief valves (3 bar, 6 bar and 7 bar relief pressures) incorporating brass bodies and an EPDM diaphragm. The valves are fitted with a hand operated rotating easing gear. Maximum working pressure 10.0 bar. Maximum operating temperature 110°C.
Ranges of solenoid valves with plastic bodies, incorporating EPDM ‘O’-rings and diaphragms. The products incorporate a plastic flow regulator and a plastic filter on the inlet. The VAI-FC model can also be supplied with a brass filter. The products incorporate a plastic flow regulator on the outlet, (except for the VAI-FC model). Maximum working pressure 10.0 bar Maximum operating temperature 85°C.
Range of spherical valves with brass bodies (nickel plated), brass ball, PTFE seats and EPDM ‘O’-rings. For use with Polybutylene pipe (manufactured to BS7291 part 2), PEX pipe (manufactured to BS7291 part 3) and copper pipe (manufactured to EN 1057). Maximum working pressure: 6 bar Maximum operating temperature: 95°C
Range of lever operated spherical valves with bronze bodies and a brass ball, EPDM ‘O’-rings and PTFE seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line spherical valves with brass body, brass ball, EPDM O-ring and PTFE gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated Spheroidal graphite cast iron bodies, EPDM seals and a non-rising stem with a handwheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies, wedge and bonnet (blue epoxy powder coated) and EPDM `O` rings and gaskets. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure: 16.0 Bar Maximum operating temperature: 60°C
Range of gate valves with brass bodies, bronze bonnet, EPDM ‘O’-ring and PTFE seat. The valves are operated via a non-rising stem and a handwheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models RSF-002A(Metal Seat) & RSF-002B(Metal Seat) incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Ranges of gate valves with ductile iron bodies (blue epoxy coated), and EPDM coated wedge with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves with blue or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass or chrome plated brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of double regulating valves with bronze bodies, DZR brass discs, EPDM `O`-rings and PTFE disc face. The valves incorporate a non-rising spindle headwork regulating the flow and isolation function. The D931, D933 and D934 models incorporate two pressure test points. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'EPDM W8528'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LH-02 EPDM Hose'. Black coloured, extruded EPDM rubber hose. Shore hardness 80. tested in-radius size 0.8mm. For use with water up to 85°C.
'B1-4651'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 60. Tested in-radius size 4.6mm. For use with water up to 23°C.
'E7001Z59-10 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'EP70 Black EPDM Diaphragm Seals'. Black coloured, compression moulded EPDM diaphragm seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘EP4118F, EP4518F, EP5118F, EP5518F, EP6118F, EP6518F, EP6512F (also known as EP6512P), E7008F, EP7118F, EP7518F, EP7068PF (added in April 2025), EP8018F, EP8118F, EP8518F & EP9118F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EJ820 'O' ring'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP1/1/5 BLK EPDM Diaphragm'. Black coloured, compression moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'Corirubber 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'ARCO-DRINKFLEX Cable'. Blue coloured, extruded, submersible EPDM cable. Shore hardness D 23. Tested in-radius size of the sheath is 2.5mm. For use with water up to 23°C.
‘EP4066F, EP4566F, EP5066F, EP5566F, EP6066F, EP6566F, EP7066F, EP 7566F, EP8066F, EP8566F, EP9066F’. Range of black coloured, compression moulded, EPDM ‘O’ rings and gaskets. Shore hardness between 40 & 90. ‘O’ rings with tested in-radii sizes of between 0.25mm & 5.00mm. Gaskets with tested in-radii sizes of between 0.25mm & 7.50mm. For use with water up to 85°C.
'E633'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP011470P(KAWN)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LETW70 - KALT70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.75mm. For use with water up to 23°C.
'51M7568'. Black coloured, injection moulded EPDM material. Shore hardness 75 ShA. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AA7BCZ'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'D0012'. Black coloured EPDM material manufactured by vulcanisation moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'70EP505p'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM-50AA2, EPDM-60AA2, EPDM-70AA2, EPDM-80AA2 & EPDM-85AA2'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 ShA & 85 ShA. Tested in-radius size 1.0mm. For use with water up to 65°C.
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel inter-locked shower hose incorporating an EPDM lining and NBR gaskets. Maximum operating temperature 85°C. Open outlet use only.
T-type thermostatic blending valve with a nickel plated brass body and EPDM ‘O’-rings. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of In-line plastic flow regulators housed within a brass bodies incorporating a plastic strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar Maximum operating temperature 65°C.
Range of thermostatic cartridges with plastic bodies, stainless steel strainers and EPDM ‘O’-rings. Maximum operating temperature 85°C. Open outlet use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 143138 X XXX | VARIOUS | 1/2" | 10.0 bar | 65 °C | PPI | Rear of body | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AL ES BAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES BAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| AL ES TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CRU TBAS C | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BLK | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| CRU TBAS BB | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313935 | Chrome | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313936 | Black | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| 313937 | Brushed Brass | 1/2" BSP | 5 bar | 65 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 197021 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | Non-rising spindle | C-plate | Aerator & Flow Straightener | |
| 207121 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 207125 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Cross top Dome or Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQSOL EFSNK C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 4648G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288489 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288491 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311098 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 3311102 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311106 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311162 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| BQMEN EFSNK BN | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF C | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF BB | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 MZ SNK EF GM | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 9087G | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288493 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 288503 | Brush Nickel | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311105 | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311114 | Brushed Brass | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311125 | Gun Metal | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| 311164 | Chrome | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | ||
| RP3 EC SNK EF BLK | Black | ½” captive nut end connections. | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disc | C-plate |
Model added February 2026: RP3 EC SNK EF BLK
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 147013 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | Non-rising spindle | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Cross Top type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| QST SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disk | C-plate | Flow Straightener | |
| RP3 DUL SNK EF C | Chrome | ½” captive nut end connections. | 5.0 bar | 60 °C | Bristan | Body | No | 1/2 Turn ceramic disc | C-plate | Flow Straightener |
Model added February 2026: RP3 DUL SNK EF C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| VAC DFBAS C MT | Chrome | G 1/2 | 5.0 bar | 60 °C | Bristan | Handle | No | Non-rising spindle | C-plate | Open Outlet | Pop Up |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HD15 | Chrome | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15K | Matte Black | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BB PVD | Zirconium gold brushed topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BV | Brushed gold matte topcoat | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15MG | Gun gray brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15CA | Rose gold brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
| HD15BN | Nickel brushed | BSP 3/4" (M) | 10 bar | 60 °C | Brand logo | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
These models only different in surface treatment
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| AL 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS C | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BLK | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| CRU 3TH BAS BB | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313941 | Chrome | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313942 | Black | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
| 313943 | Brushed Brass | G 1/2" Male | 5 bar | 65 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Flow Regulator Fitted, Interconnecting Hoses, |
Expansion vessel with a carbon steel body and EPDM membrane. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of filter shower handsets and tap outlets with plastic bodies with EPDM O-Rings Open Outlet use. Maximum operating temperature 60°C
‘GM50xx’ range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *- STPT304 and *- STPT316 stainless steel pipes. The GM5004 prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with MONFLEX PEXB/AL/PEXB MULTILAYER PIPES. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Mingshi stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Hyddro Range of stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with Hyddro stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of Hyddro press fittings incorporating EPDM ‘O’-rings. For use with Hyddro (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of M profile copper press fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of compression fittings incorporating polypropylene bodies, plastic pipe liners, plastic grip rings and EPDM seals. For use with PE100 pipe manufactured to BS EN 12201. Maximum working pressure: 16Bar. Maximum operating temperature: 23°C
‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated ductile iron flanged dismantling fittings with EPDM sealing rings. Maximum working pressure: 16 Bar. Maximum operating temperature: 65°C.
Range of ultrasonic water meters with brass bodies and EPDM O-rings. The inlets incorporate a double check valve assembly, verified by test - suitable for backflow protection against Fluid Category 3. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Water shock absorber incorporating a stainless-steel body and EPDM membrane. Maximum working pressure 15.0 bar. Maximum operating temperature 85°C.
Range of shock arrestors with a stainless-steel body and EPDM liner. The compression connection of the X2041.015 model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Shock arrestors with a copper body, plastic shuttle and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of shower booster pumps (either single or double) with acetal bodies and impellers and EPDM seals and NBR `O` rings. Supplied with stainless-steel braided EPDM lined flexible hoses incorporating isolation valves Maximum operating pressure 3.8 bar. Maximum operating temperature 65°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
Range of shower handsets and overhead showers with plastic bodies incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
A12231 & A12011 Ranges of shower handsets with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. Maximum operating temperature 65°C.
Range of shower handsets and overhead showers with plastic bodies (various finishes - see model) incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
Shower handset with plastic body (various finishes) incorporating EPDM ‘O’-rings and washers. Maximum operating temperature 65°C.
Range of interlocked EPDM lined shower hoses assemblies with EPDM gaskets. Maximum operating temperature: 85°C Open outlet use only.
Range of fixed shower arms, (brass bodies - various finishes) with EPDM O-Rings. Maximum operating temperature: 85°C, open outlet use only.
Range of Y type strainers with blue epoxy coated ductile iron bodies and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
HOS wwwxxyy z - Range of EPDM or PVC lined, interlocked stainless-steel shower hoses. Open outlet use only. Hoses with an EPDM liner have a maximum operating temperature of 85°C. Hoses with an PVC liner have a maximum operating temperature of 65°C.
Multi-layer PVC shower hoses with Black, Brushed Brass or Chrome finish with brass end connections, EPDM gasket and NBR ‘O’-ring. Open outlet use only. Maximum operating temperature 65°C
Pull Out Twist Mini and Pull Out Twist range of PET (Polyethylene terephthalate) braided flexible hoses incorporating HDPE liner and EPDM ‘O’-rings, various brass or stainless steel fitting bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Models with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel braided EPDM lined flexible hose assemblies with EPDM seals & EPDM washers, available with a variety of end connections. For use with copper pipe manufactured to EN1057 & HEP20 PB pipe. Maximum working pressure; 6 Bar Maximum operating temperature; 65°c
Range of EPDM hoses with either nylon or stainless-steel braiding, with or without a PVC sheath. Some models incorporate isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of nylon braided flexible outlet hoses, incorporating an EPDM liner, EPDM ‘O’-rings and gaskets. Maximum operating temperature 85°C.
Range of air release valves with blue epoxy coated ductile iron bodies and EPDM seats. Maximum working pressure 16.0 bar
Non-metallic materials and components comply with BS6920 at 80°C
Wall mounted thermostatic bar type shower valves with a non-rising spindle headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member which incorporates a manual override button. Each inlet incorporates a combined EPDM washer and stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is also supplied with a shower riser rail, shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of butterfly valves with (blue epoxy coated) ductile iron bodies and cast iron discs incorporating EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 60.0°C
Range of butterfly valves incorporating blue epoxy coated ductile iron bodies, stainless steel (CF8M) discs and EPDM seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of wafer and lug butterfly valves incorporating blue epoxy coated ductile iron body, either a stainless steel (CF8 or CF8M) or blue epoxy coated ductile iron disc and an EPDM seat. DN40-300 lever and gear operated, DN350-600 gear operated. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of wafer butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless-steel discs. The products are supplied with lever (D71X) or gear (D371X) operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of combined temperature and pressure relief valves incorporating DZR brass bodies and an EPDM diaphragm. Valves incorporate a manually operated rotational easing gear. The valves are pre-set at 6.0 or 7.0 bar (see models). Compression connections are for use with copper pipes (manufactured to EN 1057). Maximum operating temperature 90°C.
Equilibrium float valve with brass body, brass float arm and EPDM seals. Float not supplied and not covered under the scope of this approval. Maximum working pressure 10.0 Bar Cold water use only
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
A range of non-return valve with blue epoxy coated ductile iron bodies, stainless-steel disc and EPDM seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
UNIWAT 5107Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pressure reducing valves with DZR brass bodies (CW602N or CW511L), EPDM ‘O’-rings and a stainless steel strainer. Available with a variety of end connections (see model). Models with compression, pressfit and pushfit connections are for use with copper pipe. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressure between 1.5 bar and 6.0 bar. Maximum operating temperature 80°C.
Range of pilot operated pressure reducing control valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and O-rings. The products are supplied with auxiliary fittings: spheerical valves, pressure gauges, a pilot valve and a needle valve. Maximum inlet supply pressure 25.0 bar. The outlet pressure is adjustable between 1.5 - 17 bar. Maximum operating temperature 85°C.
Range of pre-set pressure relief valves with brass or DZR brass bodies and EPDM diaphragms. The valves are fitted with hand operated easing gear. Pre-set pressure 3.0 bar for all models. Maximum operating temperature 85°C.
Range of normally open (L282 prefix models), normally closed (L182 models) or latching (61 suffix models) solenoid valves with either brass, nickel plated brass or stainless-steel bodies and an EPDM diaphragm. Please refer to model for maximum working pressure. Maximum operating temperature 85.0°C
Range of normally closed (NC), solenoid valves with plastic bodies and EPDM diaphragm. Models with push-fit connections are for use with copper pipe (manufactured to EN 1057) and PTFE pipe. The products incorporate a plastic or stainless steel filter on the inlet, (except for models with swivel nut, push-fit and nozzle inlets, as well as the 44.007.126 and 01.021.126 models) . The 44.007.126 model incorporates a Y-pattern stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperatures: Cold water use only, 65°C or 90°C for models marked with ℗ - Please consult model section for further details.
Dual outlet solenoid valve with a plastic body, incorporating EPDM diaphragm and ‘O’-rings. The inlet incorporates a plastic flow regulator and a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Angled ball valve with a DZR brass body, chromium plated brass ball, EPDM ‘O’-ring and PTFE seats. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves with black plastic bodies, PTFE seats and EPDM ‘O’-rings. Maximum working pressure: 16 Bar. Cold Water use only.
Range of ‘EFFAST’ spherical valves with plastic bodies incorporating EPDM ‘O’-rings. For use with ABS pipe manufactured to BS 5391. Maximum working pressure: 15 Bar. Maximum operating temperature: Cold water use only.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of Gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges, non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. DN50 to DN500 sizes are operated by handwheel. DN600 to DN800 sizes are operated by a gear box. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The BT1405 & BT1406 models have a rising spindle, the BT1401 & BT1402 models have a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
GAER S12 Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
GAER S12 Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of 2, 3 ,4 or 5 way manifolds incorporating brass bodies, stop valves and EPDM O-rings, to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Monobloc manifold containing an in-line pressure reducing valve (Adjustment Range between 2.7 and 3.3 bar, but factory pre-set at 3 bar) and a pre-set expansion relief valve (pre-set pressure 6 bar) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates also a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Inlets and outlets have compression connections, for use with copper pipe to EN1057. Maximum working pressure 12 bar. Maximum operating temperature 80°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
BT1420-DFM Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'EP7007PF 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
'51M7531 Diaphragm'. Black coloured, calendered, EPDM diaphragm. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 85°C.
'3W10-70-IR'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 1.75mm. For use with water up to 85°C.
'EPDM 70.54-02 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EPDM 70.54-02 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Flexrubber EW70 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'EPDM E293'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'LR33'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.25mm. For use with water up to 23°C.
'N57140'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'1EP6052'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.12mm. For use with water up to 23°C.
'EPDM2019'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘51M5577, 51M6077, 51M6577, 51M7077, 51M7577, 51M8077, 51M8577’. Black coloured, injection moulded EPDM materials. Shore hardness between 55A & 85A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ASHUTOSH EPDM 50' & 'ASHUTOSH EPDM 80'. Black coloured, compression moulded EPDM materials with a shore hardness of 50 & 80. Tested in-radius size 1.2mm. For use with water up to 23°C.
'NER EPDM - 80'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 50°C.
'HC-EP7001165PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51M6767'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
'51M5567'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 0.5mm. For use with water up to 23°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'TWK3628'. Black coloured, injection moulded EPDM material. Shore hardness 67. Tested in-radius size 0.5mm. For use with water up to 60°C.
'07148-60'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SML-EP012EB'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C. When processing an application for WRAS Product Approval the in-radius tolerance rule cannot be applied, i.e. only the material with an in-radius of 1.0mm is covered by the scope of the approval.
'EPDM SP-002 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AP-EPDM 50A, AP-EPDM 60A, AP-EPDM 70A & AP-EPDM 80A'. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 80A. Tested in-radius size between 1.15mm & 1.21mm. For use with water up to 65°C.
'EP 70110 HC'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.56mm. For use with water up to 23°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193745 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 65 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Spring loaded, resilient trim check valve cartridge with plastic body and EPDM O-rings. For insertion into fittings with specifically sized bores. Maximum working pressure: 16 Bar. Maximum operating temperature: 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks with brass bodies and EPDM ‘O’ rings. For insertion into specifically dimensioned tap assemblies Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Non-rising spindle headworks (cast brass body) with EPDM ‘O’-rings and seat washer. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with EPDM seals. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10 Bar, Maximum operating temperature 85°C.
Quarter turn ceramic disc headwork incorporating a brass body, EPDM and NBR ‘O’-rings and a silicone gasket. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Kisdon range of single hole single outlet (swivel) pull out spray combination tap assembly (chromium plated brass) with ¼ turn ceramic disc headwork and single lever operating members. The outlet of the pull-out spray incorporates a plastic flow aerator and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with EPDM lined flexible hose assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 818JK | Chrome | 1/2" BSP | 5.0 bar | 60 °C | Bristan | Handle | No | Ceramic cartridge | C-plate | Waterfall | Click Type |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| N SNK EF C | Chrome | 15mm | 5.0 bar | 60 °C | Bristan | Handle | No | 1/4 Turn ceramic disk | Not Applicable | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HGLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS38 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| HGLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS20 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, | |
| FLLS30 | Various | 15mm | 6 bar | 65 °C | Logo | on spout | No | Plastic Backnuts | Aerator | Click Type | Flow Regulator Fitted, Interconnecting Hoses, |
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlets incorporate a plastic aerator. The products are supplied with stainless steel braided EPDM lined interconnecting hoses. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Shock arrestor with stainless steel body and EPDM diaphragm. Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.
Range of filling loop assemblies consisting of an in-line isolation valve, an in-line double check valve assembly (suitable for back flow protection against fluid category 3) that incorporates an isolation valve and a stainless-steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Page 2 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
