Samsun Makina Sanayi A.S. Approvals


WRAS Approval Number: 1701521

‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

  • Section: 5021 Bituminous Based Products
  • Section Subtitle: Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.
  • WRAS Approval Number: 1701521
  • Expiry date: 31/01/2022
  • Manufacturer: Samsun Makina Sanayi A.S.
    Company Name
    Samsun Makina Sanayi A.S.
    Address
    Organize Sanayi Bolgesi, Yasar Dogu Caddesi, No. 33 P.K. 136,
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1708544

'SMS-FBE-Dark Blue'. Factory applied, dark blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'document code 53' dated 01.06.2016. Cure for 10 minutes@160°C. For use with water up to 85°C.

  • Section: 5030 Coatings, Paints & Linings
  • Section Subtitle: Factory applied pipe & fittings coatings.
  • WRAS Approval Number: 1708544
  • Expiry date: 31/08/2022
  • Manufacturer: Samsun Makina Sanayi A.S.
    Company Name
    Samsun Makina Sanayi A.S.
    Address
    Organize Sanayi Bolgesi, Yasar Dogu Caddesi, No. 33 P.K. 136,
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1801525

‘SMS-5000, SMS-7000 & SMS-8000’. Black coloured, compression moulded EPDM materials. Shore hardness 50, 70 & 80 respectively. Tested in-radius size 1.0mm. For use with water up to 85°C.

  • Section: 5365 Rubbers
  • Section Subtitle: Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.
  • WRAS Approval Number: 1801525
  • Expiry date: 31/01/2023
  • Model
  • Manufacturer: Samsun Makina Sanayi A.S.
    Company Name
    Samsun Makina Sanayi A.S.
    Address
    Organize Sanayi Bolgesi, Yasar Dogu Caddesi, No. 33 P.K. 136,
    View All Listings by this Company

Print This Approval


WRAS Approval Number: 1811572

'SMS EPX-02'. Factory applied, two-part, blue coloured epoxy coatings consisting of component A and component B. Mix and apply as per painting instruction 'document code 30', ‘Rev. No. 7’ dated 01.09.2018. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

  • Section: 5030 Coatings, Paints & Linings
  • Section Subtitle: Factory applied pipe & fittings coatings.
  • WRAS Approval Number: 1811572
  • Expiry date: 30/11/2023
  • Model
  • Manufacturer: Samsun Makina Sanayi A.S.
    Company Name
    Samsun Makina Sanayi A.S.
    Address
    Organize Sanayi Bolgesi, Yasar Dogu Caddesi, No. 33 P.K. 136,
    View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page of 1