Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
Range of commercial, salt regenerated, electronically controlled ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Blue Epoxy GPC)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a volume ratio of 3:1 and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/W1-16’, version ‘4.0’, effective date ’01.08.2025’. Cure for 12 hours @30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/A)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL(BFSC-CEMIII/B)'. Factory applied, grey coloured Blast Furnace Slag Cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per manufacturer’s Work Instructions ‘JSAW/SMG/DISP/PRO/WI-11’, ‘Version 4.0’, ‘Effective Date 01.08.2025’. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PENTALINE DI 750 BLUE'. Factory applied, two-part, blue coloured epoxy coating. Mix parts A and B in a 3:1 volume ratio and apply as per manufacturer's TDS 'Issue date: August 2023. Reference No - 01'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tesnit BA-U Yellow & Blue'. Fibre/NBR materials, available in yellow or blue colours, manufactured by calendaring. Tesnit BA-U Blue is for use with water up to 85°C. Between September 2025 and February 2026, Tesnit BA-U Yellow was for use with water up to 23°C. Between March 2026 and September 2030, Tesnit BA-U Yellow is for use with water up to 85°C. Store and handle in accordance with 'STORING & HANDLING INSTRUCTIONS, dated November 12, 2025'. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
Grilamid LV-30H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA natural. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural & Grilamid LV-65H FWA black 9225 were added to the approval in March 2026. Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 58 130 xx0 | Various | G 1/2" | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 42 540 xx0 | Various | G 1/2" | open outlet bar | 65 °C | AXOR | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 119 xx0 | Various | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 131 xx0 | VArious | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 152 180 | NA | G 1/2" | open outlet bar | 65 °C | hansgrohe | sticker only, marking will be on the finish set | Yes | Not applicable | Not Applicable | Open Outlet |
model 58131xx0 and 58119xx0 are identical in the water pathway, only difference is the cover plate design. model 58130xx0 and 42540xx0 are both composed of the finish set 58131xx0/58119xx0 and basic set 58152180, only difference is the marking on the faceplate 58130xx0= hansgrohe, 42540xx0= AXOR
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 122 100 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 122 101 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 579 600 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 333 001 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 700 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable | |
| 30 746 702 | NA | NA | 16 bar | 70 °C | HG | on the body | Yes | Ceramic cartridge | Not Applicable | Not Applicable |
30 122 100 - Diameter= 25,4mm 30 122 101 - Diameter= 25,4mm 30 333 001 - Diameter= 25,4mm 30 746 700 - Diameter= 25,4mm 30 746 702 - Diameter= 25,4mm 30 579 600 - Diameter= 25,4mm
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 35A4 | 35mm | 25 bar | 65 °C | Hassem logo | Body | No | Ceramic cartridge | ||||
| 40A | 40mm | 25 bar | 65 °C | Hassem logo | Body | No | Ceramic cartridge | ||||
| HSP-024 | 18mm | 25 bar | 65 °C | HS, Production date(YYYYMMDD) | Body | No | Push button detent | ||||
| QB-001L | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QB-001R | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSD-A001L | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSD-A001R | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSE-N003L | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| HSE-N003R | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QB-318 | BSP 3/4" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QD-445 | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc | ||||
| QD-446 | BSP 1/2" (M) | 25 bar | 65 °C | Hassem logo | Body | No | 1/4 Turn ceramic disc |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 99078-H | 25mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99014-H | 32mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| G22151-N | 34mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99150-H | 35mm Ø | bar | 65 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99095-H | 28.5mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable | ||
| 99090-H | 28.5mm Ø | bar | 85 °C | Aerre plast and date of manufacture (MM/YY) | On body | Yes | Not applicable | Not Applicable | Not Applicable |
The cartridges 99078-H and 99014-H are re-approvals of certificate 2007006 (Expiry date: 31/07/2025) The cartridges G22151-N, 99150-H, 99095-H, 99090-H are on the same family and we would like to add to the same certificate.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) with a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a pull-out spray with plastic aerator. The pull-out spray hose connector incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) pull down spray combination tap assembly (chromium plated brass body) with a ceramic cartridge headwork and single lever operating member. The product incorporates a pull-down spray with a plastic aerator, which also incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies incorporating a ceramic cartridge headwork with a various operating member. The product incorporates a pull-out spout with a plastic aerator. Maximum working pressure 6 Bar Maximum operating temperature 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (stainless steel bodies – various finishes), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 052 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 051 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 053 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | ||
| 71 054 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator | Click Type | |
| 71 055 xx0 | various | G 3/8 | 10 bar | 60 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | C-plate | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 34 010 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Lever Operated Pop-up | |
| 34 016 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Lever Operated Pop-up | |
| 34 017 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Open Outlet | |
| 34 127 xx0 | Various | G 3/8 | 10 bar | 60 °C | AXOR | on body | Yes | Ceramic cartridge | C-plate | Aerator | Open Outlet |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WB791* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB791H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1020* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1020H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1021* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1021H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1022* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB1022H* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SL-KT053 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT014 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT015 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT004 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | Non-rising spindle | C-plate | Aerator | |
| SL-KT40602R | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT032 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Side of body | No | Ceramic cartridge | C-plate | Aerator | |
| SL-KT054 | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT30602W | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Aerator | |
| SL-KT40202L | Various | 1/2" BSP (F) | 10 bar | 60 °C | Company Logo | Rear of body | No | 1/4 Turn ceramic disc | C-plate | Flow Straightener |
Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720032 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720034 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | Ceramic cartridge | C-plate | Aerator | |
| 2720068 | Chromed | ½” captive nut | 10 bar | 60 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-WK794* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK795* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK1034* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WK305* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB792* ** | Various | ½” captive nut | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
* stands for the different handle A, B,C and D ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2720055 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Flow Straightener | |
| 2720060 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Open Outlet | |
| 2720062 | Chromed | ½" captive nut | 10 bar | 85 °C | MVI | Rear of body | No | 1/4 Turn ceramic disk | C-plate | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SJS-WB102* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| SJS-WB202* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB742* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB793-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-1* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703-2* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator | |
| JD-WB703* ** | Various | BSP 1/2" (F) | 10 bar | 60 °C | Kind | Body | No | Ceramic cartridge | Not Applicable | Aerator |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Ramge of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (stainless steel body – various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The products are supplied with nylon braided, PEX lined flexible interconnecting hoses and the spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TRLS01 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| TRLS10 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS06 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
| ZTLS07 | Various | 1/2" BSP M | 6 bar | 65 °C | Waterworks | Spout | No | 1/4 Turn ceramic disk | Plastic Backnuts | Aerator | Pop Up | Interconnecting Hoses, |
Finishes available: Brass, Chrome, Nickel, Burnished Brass, Burnished Nickel, Matte Nickel, Copper, Dark Brass, Dark Nickel, Vintage Brass, Gold, Matte Gold.
Three-hole, metal, single outlet (fixed) combination tap assembly (chromium plated brass). The product incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with stainless steel braided PEX line connecting hoses. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 36 107 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator | ||
| 36 115 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | basic set 10303180 | 10 bar | 60 °C | AXOR | on the spout | Yes | Not applicable | Aerator |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TS231** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator | |
| TS232** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Spout and handle | No | Not applicable | Not Applicable | Aerator |
** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of copper press fittings with EPDM seals for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
'Instantor’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Instantor’ stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Range of DZR brass compression fittings for use with 'Wavin PE-RT Pipe'. Maximum working pressure:20 bar Maximum working temperature:23°c
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
“>B<Press NZ” range of press fittings incorporating copper (EN12165 CW024A) or copper alloy (CC499K-DW) bodies. For use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of copper press fittings (‘M’ type crimp profile) and brass threaded adaptor fittings, for use with copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 16.0 bar @ 30°C and 10.0 bar @ 95°C.
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C.
Range of water meter measuring capsules with brass bodies. Maximum working pressure 16.0 bar. Please refer to model for maximum operating temperature.
Range of high flow water meters with black epoxy coated ductile iron bodies and EPDM gaskets. Maximum working pressure; 16 Bar Maximum operating temperature Cold water only
Range of water meter manifolds with plastic bodies, for use with MDPE pipe to BS EN 12201 pipe (for the push-fit models). The inlets incorporate a spherical valve and a non-return valve (not suitable for back flow protection). Maximum operating pressure 12.5 bar. Maximum operating temperature 23°C
Range of in-line flow sensors incorporating either brass (type 230, 235 & 236) or plastic (type 200 & 210) bodies & EPDM ‘O’-rings. Maximum working pressure 12.0 Bar Maximum operating temperature 100.0°C
Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. Maximum operating temperature 35°C.
Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.
Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 51OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52CS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52DS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6301-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6302-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6303-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 63OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6300-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OS-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OH-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator |
** Representative all models are available with the following finish code: CP-Polished Chrome BN-Brushed Nickel MB-Matte Black ORB-Oil Rubber Bronze PB-Polished Brass WP-Weathered Pewter BB-Brushed Brass
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| DS3007 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable | ||
| DS5010 | chrome | ½” BSP (F) | Open outlet bar | 85 °C | DELMEI | On handle | No | Not applicable | Not Applicable |
Range of `Y`-patterned strainers with either brass or DZR brass bodies, incorporating a stainless-steel mesh strainer. Maximum working pressure: 25.0 Bar (Models 36233, 36234, 36235, 36236, 36237 & 36238 ) or 16.0 Bar (Models 36230 & 36231 ) Maximum operating temperature 95°C. Strainers with compression connections are to be used with copper pipe manufacture to BS EN 1057. Strainers with M profile press-fit connections are to be used with copper pipe manufactured to BS EN 1057 & SS304 Stainless steel pipe manufactured to EN 10312.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20205.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20205.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20205.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20245.A20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20255.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20255.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20275.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP03-8510 | Chromed | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20305.G20.CP5R-8510 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20305.G20.CP5R-8511 | BSP 3/4" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP03-8510 | Chromed | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | ||||
| 13.20365.G15.CP5R-8510 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, size, production date (MM-YY) | Body | No | |||||
| 13.20365.G15.CP5R-8511 | BSP 1/2" (M) | 16 bar | 85 °C | Company logo (V&G), WRAS, CR, size, production date (MM-YY) | Body | No |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 13.20302.G15.CP5R-8510 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8510 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20302.G20.CP5R-8511 | ¾” BSP (M) | 16 bar | 85 °C | V&G,WRAS,3/4,MMYY,CR | BODY | No | Rising spindle | Open Outlet | |||
| 13.20362.G15.CP5R-8511 | ½” BSP (M) | 16 bar | 85 °C | V&G,WRAS,1/2,MMYY,CR | BODY | No | Rising spindle | Open Outlet |
Wall Mounted Undefinable air gap see IRNs Incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. The captive nut end connections incorporate a washer, the M10 connection incorporates an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Excelsior Range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
Range of unvented heat pump storage cylinders which consist of an air-source heat pump sitting on top of the tank with either no internal coil (model numbers ending without S) or a factory fitted single internal coil (model numbers ending with S). The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C and an stainless steel immersion heater and titanium alloy anode. The product is not supplied with an inlet control group (safety kit). Maximum operating temperature 70°C. Maximum working pressure (primary & secondary circuit) 5.5 bar.
Rinnai range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 86005640 | Chrome | 15mm compression joint | 10 bar | 80 °C | TRITON,86005640 | Handle/ body | No | Ceramic cartridge |
Range of manually operated, concealed blending valves with brass body (various finishes) and ceramic cartridge headwork and single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TSSL1 | Chrome | 15mm Compression | 5 bar | 60 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, Riser Rail, | |
| AQSL1 | Chrome | 15mm Compression | 5 bar | 60 °C | AQUALISA | shower valve | No | Single sequential | Not Applicable | Shower Hose, Handset, Riser Rail, |
Wall Mounted thermostatically controlled shower valve supplied with shower hand-set, hose with riser rail and overhead shower in chrome finish. Incorporating a 1/4 turn ceramic disc headwork & flow regulator. Maximum temperature 65°C. Maximum Pressure 5 bar.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Combined temperature and pressure relief valves with a DZR brass body, pre-set at 7.0, 10.0 or 15.0 bar. Maximum working pressure See models Maximum operating temperature 90.0°C
Range of piston type float operated valves with plastic bodies. Maximum operating pressure: 14 bar. Maximum operating temperature: 23°C.
Range of pressure reducing valves with DZR brass or bronze bodies and manually adjustable outlet pressure range between 2.5bar to 7.0bar . Maximum working pressure: 25.0 bar or 30.0 bar depending on model. Maximum operating temperature 80°C.
Range of normally closed (L182 models) solenoid valves with brass bodies. Maximum working pressure 16.0 bar: 12900 Maximum working pressure 12.0 bar: 12903 & 12906 Maximum working pressure 10.0 bar: 12909 ,12912 & 12915 Maximum operating temperature 85.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball, (DZR brass body and ball on 40 bar models). Maximum working pressure: Various – see model section. Maximum operating temperature 99.0°C
Range of nickel plated brass servicing valves, and nickel plated brass or brass (SD1001 models only) spherical valves. All products incorporate a chrome plated brass ball. SD6017, SD6003 and SD3008 valves are screw driver operated. SD6012, SD4001 and SD1001 valves are lever operated. SD4003 valves have butterfly operating members. The compression and pressfit connections are for use with copper pipes (manufactured to EN1057). Pressfit connection jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressures: SD3008 valves: 10.0 bar, SD6017, SD6012 and SD1001 valves: 16.0 bar, SD4003, SD6003 and SD4001 valves: 25.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with nickel plated brass bodies and chromium plated brass balls. The valves are either screwdriver or lever operated(see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (HC-A61055-22 model) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with brass or DZR brass bodies incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of magnetic scale reducers with metal bodies, for use with copper pipe (manufactured to EN 1057). Maximum working pressure 12 Bar. Maximum operating temperature 30°C.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
'WITCOAT HIGH BUILD BITUMINOUS BLACK PAINT'. Factory applied, black coloured bitumen paint. Apply as per manufacturer's TDS, dated '28.06.2025'. Cure for 72 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GDPA PermaCoat'. Factory applied, blue coloured (once applied) coating system comprising of a Yellow Zinc Primer and Polyamide top coat. Apply one coat of Yellow Zinc as per work instructions 'PR/WI/01', revision '00', dated '22/11/2017', plating for 45 minutes@30°C. Apply one coat of top coat as per work instructions 'BR/WI/01', revision '00', dated '29/10/2010' and cure for 30 minutes@215°C. For use with water up to 23°C. This material is only approved for the plating and curing conditions that appear on the approval. If the plating and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BAJ0002'. Factory applied, blue coloured epoxy coating. Pre-heat substrate for 30 minutes@200°C and apply in accordance with manufacturer's Product Instructions 'Version-01 202426 September'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RADILON® DT RV300RKC2 205 WT'. White coloured, injection moulded, glass filled Polyamide 612 material. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'Menzolit SMC1000 3018-White'. White coloured, hot-press compression moulded Polyester Sheet Moulding Compound (SMC). For use with water up to 30°C.
'ECOTRAN E2130W(#) NC'. Natural (appears beige) PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'ECOTRAN E2130W(#) BK'. Black coloured PPS material manufactured using Melt compounding method. For use with water up to 85°C.
'RAMOFIN PPH301G6NT'. White/beige coloured, injection moulded polypropylene material. For use with water up to 85°C.
'TIMCO VESF 300/VESF 410'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 01.12.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEICONLOCK AN 306-20'. Green coloured anaerobic adhesive. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Griffon WDF-05®'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6306959 20251027'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions 'PLUMEFF', dated '2024/09/17'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW105112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW103112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW125003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008002XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008003XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW111002001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106010001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW112007001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW116001000XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel).
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 090 8xx | Various | G 1/2" | 10 bar | 65 °C | AXOR | on the nut | Yes | Not applicable | Not Applicable | Not Applicable | Shower Hose, |
Where 8xx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Range of shower kits with a shower hose, handset and shower rail. Open outlet use only Maximum operating temperature 60.0°C
Range of concealed, manually operated blending valves (brass bodies - various finishes), incorporating a ceramic cartridge headwork controlling the flow and temperature, a manually operated diverter to shower outlet with lever type operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TVS106353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS103353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT127001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS112003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS125003000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS104353000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS107005000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS106353113xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVT111001000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS122002000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS108008000xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS105353110xx | null | 1/2" F | 10 bar | 60 °C | V&B Logo | Operating Member | Yes | Ceramic cartridge | null | null | null | |
| TVS00035100000 | null | 1/2" F | 10 bar | 60 °C | null | null | Yes | Ceramic cartridge | null | null | null |
TVS00035100000 – Vi-Box is used in conjunction with all of the models. Where xx denotes the surface finish (which is a non-water contact part) 61 = Chrome, 74 = Brushed Chrome, 64 = Brushed Nickel Matt, 65 = Polished Nickel, 60 = English Gold, 76 = Brushed Gold, K5 = Matt black, 70 = Dune, 63 = Graphite
Range of ceramic cartridge headworks for insertion into specifically dimensioned tap assemblies. Maximum working pressure 12.0 bar Maximum operating temperature 85°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members.The spout otlet incorporates a plastic aerator. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T5002 | Chrome plating | ½” BSF (F) Captive nut | 5 bar | 65 °C | SONAS | on operating member | No | Ceramic cartridge | C-plate | Aerator |
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Model 24.272.xx1 is supplied with a lever type pop-up waste set – not verified by test.. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 521502 - KANO TP HP CHR | Chrome (CHR) | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525028 - KANO TP HP ANT / CHR | ANT / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525030 - KANO TP HP SGW / CHR | SGW / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 525033 - KANO TP HP CAF / CHR | CAF / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526175 - KANO TP HP BLA / CHR | BLA / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526667 - KANO TP HP BL | BL | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526950 - KANO TP HP VGR / CHR | VGR / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator | |
| 526951 - KANO TP HP SOW / CHR | SOW / CHR | 3/8"" | 10 bar | 70 °C | BLANCO | body | Yes | Ceramic cartridge | Not Applicable | Aerator |
CHR - Chrome ANT - anthracite SGW - silgranite white CAF - coffee BLA - black BL - black matt VGR - volcano grey SOW - soft white
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ROC2MB | MATT BLACK | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2RC | REGENCY COPPER | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2AB | ARTISAN BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2BN | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ROC2PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BV | MATT BLACK | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073RC | REGENCY COPPER | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073AB | ARTISAN BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| TU81073BS | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITCP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITPB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| VITBS | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2PB | PATINATED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2BN | BRUSHED NICKEL | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| SA2CP | CHROME | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ZO3BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator | |
| ZO2BB | BRUSHED BRASS | 1/2" BSP | 5 bar | 60 °C | cleanwater | on bottom of faucet | No | Ceramic Cartridge | C-plate | Aerator |
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (brass body, various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a ceramic disk diverter with dome type operating member controlling the flow between the outlets. The spout outlet incorporates a plastic aerator. Maximum working pressure: 10.0 Bar Maximum operating temperature: 60°c
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1001JC45 | Chrome | ½” BSP (M) x ¾” BSP (M) offset union | 10 bar | 85 °C | HUANRI | Rear of body | No | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M33275 X XXX | VARIOUS | 3/4” BSP male inlet. | 5 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks and lever type operating members. The spout outlet incorporates a plastic aerator and supplied with metal back nuts. Maximum operating pressure 5.5 bar. Maximum operating temperature 60°C
Expansion vessels incorporating a stainless-steel body and SEFA membrane. Maximum working pressure: 10 bar, except A2C2R27 WR000 (DP 24/16X) 1” BSPP (M) which is 16 bar. Maximum operating temperature 85˚C.
Range of expansion vessels having stainless steel bodies. Maximum operating pressure 7 - 25 bar. Maximum operating temperature 85°C
‘EPS’, ‘EPT & ‘EPL’ ranges of PPSU press fittings (TH press profile) with EPDM ‘O’-rings for use with ‘EFIELD EA’ PE-Xb/AL/PE-Xb multilayer pipes. Maximum working pressure: 10 bar. Maximum operating temperature: 95°C
Range of press fittings (brass bodies) with stainless steel press (‘TH’ profile) collars and EPDM o-rings for use with ‘EA’ PE-Xb/AL/PE-Xb’ multilayer pipe (for press fitting connections) or copper pipe manufactured to EN1057 (compression connections). Maximum working pressure: 10 bar. Maximum operating temperature: 95 °C.
Stainless steel M-profile press-fit fittings (316L) and pipes (316L - EN 10312 and 304 – EN 10312). Maximum operating pressure 16 bar. Maximum operating temperature 100°C.
Flowflex Range of press-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with SS316L pipes. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of copper or chrome plated copper (CP suffix models) press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressures: 12mm to 54mm: 16.0 bar, 66.7mm to 108mm: 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘V’ profile. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of domestic stainless steel indirect unvented hot water storage cylinders, incorporating a stainless-steel coil for connection to external heating resource. The secondary circuit is factory fitted with a temperature and pressure relief valve (7.0 Bar @90°C) and an immersion heater. Primary working pressure: 3 bar; secondary working pressure: 5.5 bar. Maximum operating temperature 90 °C.
FVC & FVS Ranges of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| WJ V/HANDLE CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 931 IX | STAINLESS STEEL | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 23931 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 27931 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 28931 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 21931 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 649510 CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 639510 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 679510 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 689510 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 619510 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH G | POLISHED GOLD | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH NK | NICKEL | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ GRSH BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 15930 CH | CHROME | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 23930 BBR | BRUSHED BRASS | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 27930 BBL | BRUSHED BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 28930 MB | MATT BLACK | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No | ||||
| WJ 21930 BRZ | BRUSHED BRONZE | 1/2BSP(M) | Open Outlet bar | 60 °C | ZHONG RUI YI SHENG | on shower body | No |
Range of ‘THINK-A-FLEX’, EPDM lined, stainless steel braided flexible hose assemblies incorporating various end connections Maximum working pressure: 10 BAR Maximum operating temperature: 65°C
Range of gas fired, unvented hot water storage heaters. The DHW circuit consists of a temperature and pressure relief valve (set at 7.0Bar). Maximum working pressure: 6.5 Bar. Maximum operating temperature: 85°C.
Range of single or double tank water heaters, incorporating enamel coated carbon steel tank. The secondary circuit is factory fitted with a temperature and pressure relief valve (10.0 Bar). Maximum working pressure 8 bar. Maximum operating temperature 75 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F1100* | chrome or matte black | 3/4” BSP(F) | 5 bar | 85 °C | KY-LIN | on body | No | Ceramic cartridge |
Where * denotes the finish color, and can be replaced with the following: CHR = Chrome BLK = Matte Black The inlets incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SD-ZJXXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD124-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD205-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD127-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD170-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD190-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD246-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD191-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD109-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD207-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD101-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD116-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD117-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD125-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD128-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD156-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD168-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD209-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD210-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD212-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD213-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD220-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD222-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD236-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD238-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc | |||
| SD240-XXXX | Chrome | 3/4BSP(F) | 10 bar | 60 °C | SHENGDIAN,“H” and “C” | on face Panel | No | 1/4 Turn ceramic disc |
XXXX represent five series shower valves and can be replaced to 2500, 2501, 2503, 2504, 2702.
Range of butterfly valves with blue epoxy coated ductile iron bodies, stainless-steel discs and EPDM or PTFE seats (see models). Maximum working pressure 16.0 Bar or10.0 Bar (see models). Maximum operating temperature 85°C.
Range of wafer non-return valves with stainless steel (SUS304 or 316) or galvanized carbon steel (A105) bodies, stainless steel discs (CF8 or CF8M) and either EPDM or FKM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of swing gate, non-return valves with blue epoxy coated ductile iron bodies and EPDM swing gates. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves incorporating brass bodies and ball. Maximum working pressure see models. Maximum operating temperature 100°C.
Screwdriver operated angled spherical valve with a brass body and ball, PTFE seats and EPDM ‘O’-rings. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Gate valves with a blue epoxy coated ductile iron body, ductile iron wedge encapsulated in EPDM and EPDM ‘O’-rings. The valves operate via a non-rising spindle headwork with a hand wheel operating member. Maximum working pressures: DN50 - DN300: 25.0 bar. DN350 - 600: 16.0 bar. Maximum operating temperature 85°C.
Range of blue epoxy coated ductile iron gate valves with an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
'NP TANK 500 PW'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A & B in a 3:1 volume ration and apply two coats as per manufacturer's TDS '0724'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Safecure Super’. White coloured, spray applied SBR latex solution intended to act as a concrete curing membrane. Apply as per manufacturer`s 'Tech Data Sheet no. 306', 'Revision no. v4', dated '02.01.2026'. Cure for 14 days at 25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Durethan BKV30F 901510 SR1'. Black coloured, injection moulded nylon material. For use with water up to 65°C.
'Chemiline AG 030 FB 62'. Black coloured, EPDM material manufactured by calendaring. Shore hardness 60A. Tested in-radius size 1.0mm. For use with water up to 65°C.
'KEG-2003H-30, KEG-2003H-40, KEG-2003H-50, KEG-2003H-60 & KEG-2003H-70 (no postcure)'. Translucent, compression moulded, silicone rubber materials. Shore hardness between 30 & 70. Tested in-radii sizes between 0.18mm & 5.9mm. For use with water up to 85°C.
Bottom entry or side entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use
Range of WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| WJ OUTLET CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ OUTLET IX | STAINLESS STEEL | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 23OUTLET BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 27OUTLET BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 28OUTLET MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 21OUTLET BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO4WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO3WS BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO7WS BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO8WS MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO1WS BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ KO41218 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ KO31218 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ KO71218 BBL | BRUSHED BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ KO81218 MB | MATT BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ KO11218 BRZ | BRUSHED BRONZE | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 641218 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 631218 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 671218 BBL | BRUSHED BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 681218 MB | MATT BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 611218 BRZ | BRUSHED BRONZE | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 151218 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 231218 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 271218 BBL | BRUSHED BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 281218 MB | MATT BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 211218 BRZ | BRUSHED BRONZE | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 64129510 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 63129510 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 67129510 BBL | BRUSHED BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 68129510 MB | MATT BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 61129510 BRZ | BRUSHED BRONZE | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 64 ROUND-WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 63 ROUND-WS BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 67 ROUND-WS BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 68 ROUND-WS MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 61 ROUND-WS BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ GR761281 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ GR761281 G | POLISHED GOLD | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ GR761281 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ GR761281 NK | NICKEL | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ Traditional/WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ Traditional/WS BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ Traditional/WS G | POLISHED GOLD | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ Traditional/WS NK | NICKEL | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ ROUND/WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 23ROUND/WS BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 27ROUND/WS BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 28ROUND/WS MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 21ROUND/WS BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ ESRWS001 CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 23ESRWS001 BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 27ESRWS001 BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 28 ESRWS001 MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 21ESRWS001 BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 32SQUARE/WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 33SQUARE/WS BBR | BRUSHED BRASS | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 37SQUARE/WS BBL | BRUSHED BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 38 SQUARE/WS MB | MATT BLACK | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 31SQUARE/WS BRZ | BRUSHED BRONZE | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, | |||
| WJ 15129510 CH | CHROME | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 23129510 BBR | BRUSHED BRASS | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 27129510 BBL | BRUSHED BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 28129510 MB | MATT BLACK | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ 21129510 BRZ | BRUSHED BRONZE | 1/2BSP(F) | bar | 60 °C | ZHONG RUI YI SHENG | on riser rail | No | Shower Hose, Handset, Riser Rail, | |||
| WJ SQUARE/WS CH | CHROME | 1/2BSP(M) | bar | 60 °C | ZHONG RUI YI SHENG | on shower body and wall mounted elbow | No | Shower Hose, Handset, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| T8015 - 06 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8015 - 06 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8108 - 14 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8108 - 14 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8037 - 05 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8037 - 05 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81011 - 02 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81011 - 02 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81073 - 02 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81073 - 02 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8001D - 03 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8001D - 03 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8037A - 01 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8037A - 01 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81022 - 04 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81022 - 04 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81071 - 02 - C | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T81071 - 02 - H | Natural | 1/2" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| QT8001B - 02 - C | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| QT8001B - 02 - H | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| QT8231 - 02 - C | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| QT8231 - 02 - H | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T80501 - 05 - H | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T80501 - 05 - C | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8231 - 02 - H | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8231 - 02 - C | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8001B - 02 - H | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk | |||
| T8001B - 02 - C | Natural | 3/4" BSP | 10 bar | 85 °C | SHANHU | on shell | No | 1/4 Turn ceramic disk |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| UALA305 | Chrome plated | 1/2" BSP (F) | 10 bar | 65 °C | UK BATHROOMS LTD | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| UKB8922W | Chrome plated | 1/2" BSP (F) | 10 bar | 65 °C | UK BATHROOMS LTD | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| UKB9072W | Chrome plated | 1/2" BSP (F) | 10 bar | 65 °C | UK BATHROOMS LTD | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| UKB7202W | Chrome plated | 1/2" BSP (F) | 10 bar | 65 °C | UK BATHROOMS LTD | Handle | No | Ceramic cartridge | C-plate | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 3320-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3188-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3313-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3322-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3322A-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3322B-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3274-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator | |
| 3271-** | Various | 1/2" BSP (F) | 5 bar | 65 °C | CARLOTA | Handle | No | Ceramic cartridge | C-plate | Aerator |
Where ** represents finish and can be replaced by: CR = Chrome plated, MB = Matt black， BB = Brushed brass， BN = Brushed nickel, GM = Gun Metal
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5301* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On body | No | 1/4 Turn ceramic disk | C-plate | Aerator | |
| 5301H* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On body | No | 1/4 Turn ceramic disk | C-plate | Aerator |
* denotes finish and can be replaced by: C - Chrome, RG - Rose Gold, BTG - Brushed Titanium gold, BZG - Brushed Zirconium gold, BRG - Brushed Rose gold, MW - Matte white, BS - Brushed stainless, BN - Brushed nickel, PN - Polished nickel, GM - Gunmetal, B - Matte black, TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MA3590 | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3590P | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3591 | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3591PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3592 | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3594 | chrome | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3594P | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate | ||
| MA3594PC | black | 3/8" BSP | 10 bar | 60 °C | GAOAO | on back of body | No | Ceramic Cartridge | C-plate |
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes) incorporating quarter turn ceramic disc headworks with hand wheel operating members (ZA1145SG model) or a ceramic cartridge headwork with a single lever operating member (all other models). The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 517720 - DARAS TP HP CHR MIXER TAP 3/8" | Chrome (CHR) | 3/8" | 5 bar | 60 °C | BLANCO | body | Yes | Ceramic cartridge | C-plate | Aerator | |
| 523286 - DARAS TP HP CHR MIXER TAP | Chrome (CHR) | 1/2" | 5 bar | 60 °C | BLANCO | body | Yes | Ceramic cartridge | C-plate | Aerator | |
| 526360 - DARAS TP HP 3L CHR MIXER TAP | Chrome (CHR) | 1/2" | 5 bar | 60 °C | BLANCO | body | Yes | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| 526361 - DARAS TP HP 6L CHR MIXER TAP | Chrome (CHR) | 1/2" | 5 bar | 60 °C | BLANCO | body | Yes | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 61409 | Chrome plated | 1/2" BSP (F) | 10 bar | 85 °C | Bokeya | Body | No | 1/4 Turn ceramic disc | C-plate | Flow Straightener | |
| 61109 | Chrome plated | 1/2" BSP (F) | 10 bar | 85 °C | Bokeya | Body | No | 1/4 Turn ceramic disc | C-plate | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-5030* ** | Various | 1/2" captive nut | 10 bar | 65 °C | kind | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes). Incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Wall mounted, two hole, single outlet (swivel) combination tap assembly incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| QST DSM C | Chrome (Cr6) | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Plinth | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| RP3 QST DSM C | Chrome (Cr3) | 1/2" BSP (M) | 5.0 bar | 65 °C | Bristan | Plinth | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5303* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On spout | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5302* | Various | 1/2" BSP (F) | 10 bar | 65 °C | LUSSO | on spout | No | 1/4 Turn ceramic disk | Not Applicable | Aerator | |
| CRS014* | Various | 1/2" BSP (F) | 10 bar | 65 °C | LUSSO | on Rosette | No | 1/4 Turn ceramic disk | Not Applicable | Aerator |
*denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 53110* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
| CRS013* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On base of spout | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | Interconnecting Hoses, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of water hammer/shock arrestors with brass and copper bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of water hammer/shock arrestors with brass and copper bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of expansion vessels with epoxy coated bodies. Maximum working pressure of 8.6 bar. Cold water use only.
Range of stainless steel (304 or 316L) ‘M’ profile press fittings with EPDM ‘O’-rings and stainless steel (304 or 316L) pipes. Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of brass press fittings for use with MLC PE-RT/AL/PE-RT pipe. Maximum operating pressure 10 bar. Maximum operating temperature 80°C
Range of press fittings (brass bodies) “KMU” with stainless steel press (‘U’ profile) collars and EPDM O-rings for use with “KELOX” range of PERT/AL/PERT multilayer pipe (‘butt welded’ variant 16mm-63mm & ‘lap welded’ variant 16mm-20mm). Maximum working pressure: 10 bar. Maximum operating temperature: 85°C.
Uponor S-Press composite fittings, Uponor S-Press composite PPSU reducers with S-Press PLUS composite PPSU nipples, Uponor RS fittings & Uponor S Press Metal Press fittings for use with for use with Uponor MLC pipe. Maximum working pressure and operating temperature: 10.0 bar@70°C
Range of brass or copper capillary solder ring fittings for use with copper pipe. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of brass and copper end feed fittings for use with copper pipe (manufactured to EN 1057). For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
Type ‘J’ range of plate heat exchangers with stainless steel (AISI 304L or AISI 316L) fin and end plates. Maximum working pressure 3.0 bar (primary circuit) and 10.0 bar (secondary circuit). Maximum operating temperature 80°C.
Range of copper brazed, stainless steel (316) heat exchangers in various sizes (4-300 plates, see models). Maximum working pressure: see models. Maximum operating temperature: 99°C.
Range of inline water meters with brass bodies Maximum working pressure 16.0 Bar. Cold water Only.
Range of pressure transmitters with stainless steel bodies. Maximum working pressure 100.0 Bar Maximum operating temperature 80.0°C (Type 540) or 100.0°C (Type 520 & Type 522)
Circulation pumps with either bronze or stainless pump bodies and a plastic impeller. Maximum supply pressure 10.0 bar. Maximum operating temperature 85°C.
Range of rotary vane pumps with either brass, stainless-steel or plastic bodies, stainless steel impellor and EPDM ‘O’ rings. Maximum working pressure 20 Bar. Cold water use.
Range of inline (301) or angle pattern (302) radiator valves with nickel-plated brass bodies, PTFE seats and EPDM sealing rings. The products are supplied with a dome operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of shower outlets and shower sets, the inlet incorporates a single check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). The product incorporates a flow regulator. Open outlet use only. Maximum operating temperature 70°C
A range of Shower handsets in various finishes. Open outlet. Maximum operating temperature 60 °C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| A108102 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A110101 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A111101 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A173102 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A173302 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A184101 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A184302 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A213101 | Chromed | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | ||||
| A215101 | Chromed | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | ||||
| A220103 | Chromed | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | ||||
| A238104 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A239104 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A258102 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A259102 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A268102 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A269102 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A293102 | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | |||||
| A297101 | Chromed | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | ||||
| A298101 | Chromed | BSP 1/2" (F) | Open outlet use only bar | 65 °C | Oshince logo | Face | No | ||||
| A506101 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A515301 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A515302 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A520301 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No | ||||
| A520302 | Chromed | BSP 1/2" (M) | Open outlet use only bar | 65 °C | Oshince logo | Body | No |
Range of Y-patterned strainers with blue epoxy coated ductile iron bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Y-patterned strainers with blue epoxy coated ductile iron bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass or DZR brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| VAL2 HNK FL5 C CD | Chrome (Cr6) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, |
| VAL2 HNK C CD | Chrome (Cr6) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| VAL2 HNK C 6 CD | Chrome (Cr6) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| VAX HNK C | Chrome (Cr6) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| VAC HNK C MT | Chrome (Cr6) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| RP3 VAL2 HNK C 6 CD | Chrome (Cr3) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| RP3 VAL2 HNK C CD | Chrome (Cr3) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| RP3 VAX HNK C | Chrome (Cr3) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| RP3 VAC HNK C MT | Chrome (Cr3) | 1/2" BSP (M) | 5 bar | 60 °C | Bristan | Operating member | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TPASHBAS3 | Chromed | BSP 1/2" (M) | 10 bar | 65 °C | Lecico | Rear of body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| TPASHBATH3 | Chromed | BSP 3/4" (M) | 10 bar | 65 °C | Lecico | Rear of body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| TPSOUBAS3 | Chromed | BSP 1/2" (M) | 10 bar | 65 °C | Lecico | Rear of body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| TPSOUBATH3 | Chromed | BSP 3/4" (M) | 10 bar | 65 °C | Lecico | Rear of body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 794110 | Chrome | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| 794110S | Satine | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| 794110BK | Black | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| 794120 | Chrome | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| 794120S | Satine | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
| 794120BK | Black | 3/8" | 5 bar | 60°C °C | DELABIE | On the push button | Yes | Time-flow | Metal Backnuts | Aerator | Flow Regulator Fitted, |
S : for satine finish BK : for Black finish
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined flexible hose assemblies with DZR brass end connections. Some models incorporate spherical valves. Pushfit and compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of stainless steel braided, EPDM lined flexible hose assemblies with DZR brass end connections. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of stainless steel or stainless steel with nylon, EPDM lined flexible hose assemblies with DZR brass end connections. Models 128-3009 CST & YU-JQAL222A are stainless steel wire, all other models are stainless steel with black nylon outer. Some models incorporate spherical valves, see models. Pushfit and compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of automatic air venting valves with a brass body and a plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 48 712 xx0 | Various | basic set 48710180 | 10 bar | 60 °C | AXOR | on the handle | Yes | Ceramic cartridge | Not Applicable | ||
| 48 722 xx0 | Various | basic set 48710180 | 10 bar | 60 °C | AXOR | on the handle | Yes | Ceramic cartridge | Not Applicable | ||
| 48 713 xx0 | Various | basic set 48720180 | 10 bar | 60 °C | AXOR | on the handle | Yes | Ceramic cartridge | Not Applicable | ||
| 48 723 xx0 | Various | basic set 48720180 | 10 bar | 60 °C | AXOR | on the handle | Yes | Ceramic cartridge | Not Applicable | ||
| 48 710 180 | NA | G 1/2 | 10 bar | 60 °C | hansgrohe | embossed on the body | Yes | Ceramic cartridge | |||
| 48 720 180 | NA | G 1/2 | 10 bar | 60 °C | hansgrohe | embossed on the body | Yes | Ceramic cartridge |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish. Product needs to be installed with the dedicated basic set.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| RNDSCBV2.MB | Matt Black | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| AQ150BAR2 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 300RSC | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| TWBAR2.21 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| AQ150BAR2.MB | Matt Black | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| TS150BAR2 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 126HP | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 126HP.MB | Matt Black | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| AQSQBAR2 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| TSSQBAR2 | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 408HP | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| 300SSC | Chrome | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
| AQSQBAR2.MB | Matt Black | ½”x ¾” BSP (M) offset unions or 15mm compression | 5.0 bar | 65 °C | Aqualisa | Valve Body | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Fixed Head, Riser Rail, |
The “*” is for a different Overhead Shower, Shower Hose or Shower Handset, which represent the letters A to Z X XXX Denotes the following: First X: Different handle The second, third & fourth XXX for different finishes: Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of concealed, thermostatic shower blending valves, incorporating a brass body and a (chrome plated) functional trim set. The functional trim set comprises of a quarter turn ceramic disc headwork, or a 2 or 4 way ceramic disc diverter headwork. Maximum working pressure 5 bar. Maximum operating temperature 70°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of double spring loaded, non-return valves with blue epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of non-return, swing gate valves with brass bodies and brass discs with a NBR gasket. . Maximum working pressure 16.0 bar or 20.0 bar. Maximum operating temperature 85°C.
Range of pilot operated pressure reducing valves with ductile iron bodies (blue epoxy coating) and EPDM diaphragm and O-rings. The products are supplied with auxiliary fittings: spherical valves (bronze or stainless steel), pressure gauges, a pilot valve, a needle valve and stainless steel or copper tubes. Maximum inlet supply pressure 16.0 bar. The outlet pressure is adjustable between 0.67~16.0 bar. Maximum operating temperature 85°C.
Range of motorised spherical valves with a stainless-steel body and a separate control box. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedges and a non-rising spindle with a handwheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies. EPDM coated ductile iron wedges and a non-rising spindle headwork. Some models incorporate a bypass. Maximum working pressure 16.0 bar. Maximum operating temperature 45°C.
Range of balancing valves with blue epoxy coated ductile iron bodies incorporating blue epoxy coated ductile iron (DN50~DN150) or stainless steel discs (DN200~DN300), EPDM gaskets and ‘O’-rings, handwheel operating member and a measuring port at each flanged end. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply at a Relative Humidity of below 60% as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the RH & curing conditions that appear on the approval. If the RH and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nav-Coat Bitumen Paint 001 Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's product information sheet issued '10.07.2009'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat FBE Red RAL 3013' (red coloured) & 'Eco Coat FBE Blue RAL 5017' (blue coloured). Factory applied Epoxy coatings. Apply as per manufacturer's Instructions for Use 'Doc. No.:SPPR/L3/WI/PRD/28A'. Cure for 45 minutes@220°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CP REVOLVE N-307 Deep Green'. Dark green coloured, roto-moulded polyethylene material. For use with water up to 85°C.
‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 604587 X XXX | VARIOUS | 3/4” BSP male inlet. | 10 bar | 65 °C | TP | Back of the mixer tap body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1044-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1034-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1033-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1032-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1031-XX | Various | ¾” BSP (M) | 10 bar | 60 °C | CARLOTA | BODY | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator |
1.For the series 1044-XX, 1034-XX,1033-XX,1032-XX,1031-XX, the only difference is handle style. 2.XX represent different finishes and can be replaced by CR =Chrome, MB=Matte black, BB=Brushed brass, BN=Brushed nickel,GM=Gun Metal.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SHRABSMCH | Chromed | 15mm compression | 10 bar | 65 °C | Lecico | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | Aerator | |
| SHZABSMCH | Chromed | 15mm compression | 10 bar | 65 °C | Lecico | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | Aerator |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F2300120012060 | Chrome plated | ½” BSP (F) conical nut x ½” BSP(F) nut | Open outlet use only bar | 85 °C | Justlink WRAS 2025 | Nut | No | Open Outlet |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| JD-744* ** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Handle | No | Not applicable | Not Applicable | Open Outlet | Flow Regulator Fitted, Shower Hose, Handset, |
| SJS-200* ** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Handle | No | Not applicable | Not Applicable | Open Outlet | Flow Regulator Fitted, Shower Hose, Handset, |
| JD-795* ** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Handle | No | Not applicable | Not Applicable | Open Outlet | Flow Regulator Fitted, Shower Hose, Handset, |
| JD-300* ** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Handle | No | Not applicable | Not Applicable | Open Outlet | Flow Regulator Fitted, Shower Hose, Handset, |
| JD-798* ** | Various | BSP 1/2" (M) | Open outlet use only bar | 60 °C | Kind | Handle | No | Not applicable | Not Applicable | Open Outlet | Flow Regulator Fitted, Shower Hose, Handset, |
The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| XB-LY-011C | Chrome | ½" x ¾" BSP (M) offset union | 10 bar | 65 °C | XUSHENG | BODY | No | Single sequential | |||
| XB-LY-017C | Chrome | ½" x ¾" BSP (M) offset union | 10 bar | 65 °C | XUSHENG | BODY | No | Single sequential |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F3063S-** | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | LAN BIAO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| F3064S-** | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | LAN BIAO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable |
** denotes finish: No Suffix = Chrome, H = Black, DYB = Matte white, BZ = Perl white painted, HGTS = Red bronze, HTL = Yellow bronze brushed, Q = Bronze, QTSL = Bronze brushed bright, QTS = Bronze brushed matte, STS = Acid copper brushed, SDMGJ = Water plated rose gold, N = Nickel brushed bright light, NP = Nickel brushed, TJ = Titanium gold, TJLS = Titanium gold brushed, G = Gold, GJS = Gold brushed, GJSY = Zirconium gold wire drawing matte, PGJFY = Zirconium gold wire drawing matte bright light, PLSJ = Brushed gold, LSJY = Brushed gold matte, MGJ = Rose gold, MGJL = Rose gold brushed, DMGJ = Light rose gold brushed, HTS = Red bronze brushed, QHP = Grey, LSQH = Grey brushed, LHMGJ = Brushed yellow rose gold.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| S002* | Various | 3/4" BSP (F) inlets and 1/2" BSP (F) outlets | 10 bar | 65 °C | WINSDRUM | On cover plate | No | Ceramic cartridge | Not Applicable | Aerator | Shower Hose, Handset, Fixed Head, |
| S013* | Various | 1/2" BSP (F) | 10 bar | 65 °C | WINSDRUM | On cover plate | No | 1/4 Turn ceramic disc | Not Applicable | Aerator | Shower Hose, Handset, |
| S014* | Various | 3/4" BSP (F) inlets and 1/2" BSP (F) outlets | 10 bar | 65 °C | WINSDRUM | On cover plate | No | 1/4 & 1/2 Turn ceramic disc | Not Applicable | Aerator | Shower Hose, Handset, Fixed Head, |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Model B3306AA & B1148AA are supplied with a lever type operated pop-up waste – not verified by test. Products are supplied with 3/8” x 15mm Compression adaptors for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with a permanently open type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SAVOY | Chrome | G ½” | 5 bar | 60 °C | CARRON PHOENIX | OPERATING MEMBER | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| FUJI | Chrome | G ½” | 5 bar | 60 °C | FRANKE | OPERATING MEMBER | No | Ceramic cartridge | C-plate | Aerator | Flow Regulator Fitted, |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| DU SNK FL5.6 C | Chrome | 1/2" BSP | 5 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | C-plate | Aerator | Flow Regulator Fitted, |
Wall mounted, two-hole, single outlet, fixed combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a built in anti-splash device and the product is supplied with metal backnuts. Maximum working pressure; 10Bar Maximum operating temperature 85°C
Two-hole, deck mounted, single outlet (fixed) combination tap assembly, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with metal back nuts, a plastic aerator and stainless steel braided EPDM lined interconnecting hoses. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Wall mounted concealed two-hole, single outlet (fixed) combination tap assembly (brass body - various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate an aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1188-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| 1271-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| 1274-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| 1313-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Flow Straightener | |
| 1320-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1322-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1322A-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator | |
| 1322B-** | Various | 3/4" BSP (M) | 5 bar | 65 °C | CARLOTA | Body | No | 1/4 Turn ceramic disc | Metal Backnuts | Aerator |
Where** represents finish and can be replaced by: CR=Chrome plated MB=Matt black BB=Brushed brass BN=Brushed nickel GM=Gun Metal
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 53011* | Various | ½" captive nut | 10 bar | 65 °C | LUSSO | On body | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator |
* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black
Range of three-hole, single outlet (fixed) wall mounted, concealed tap assemblies, (brass bodies - various trim sets). Product is supplied with a rough in set BDM-MIX-C309-T2 and external trim (see models). Incorporating quarter turn ceramic disc headworks and dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of three-hole, single outlet (fixed) wall mounted, concealed tap assemblies, (brass bodies - various trim sets). Product is supplied with a rough in set BDM-MIX-C309-T2 and external trim (see models). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C)
Four-hole, single outlet (fixed) combination tap assembly (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members and stainless steel braided EPDM lined interconnecting hoses. The spout outlet incorporates a self-cancelling diverter to the shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).and a plastic flow straightener with stainless steel mesh strainer. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of expansion vessels with plastic bodies and elastomeric diaphragms. Maximum working pressure: 8.6 Bar. Cold water use only.
Range of socket fusion fittings (PP-RCT) for use with PP-RCT “KELEN” pipes. Maximum working pressure 10.0 bar. Maximum operating temperature: 70°C for sizes DN20-DN63 & cold water use only for sizes DN75-DN110.
Range of stainless-steel (304/316L) press fittings with EPDM ‘O-rings to be used with stainless-steel (304/316L) pipes. The HF fittings also incorporate an EPDM gasket. Jointing is achieved via a crimping tool using a ‘V’ profile. For above ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
VSH XPRESS Range of ‘M’ profile stainless steel press fittings with EPDM ‘O’-rings for use with VSH SudoXPress stainless steel tube. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Plastic bodied push fit fittings for use with Shin Won Tube Co., Ltd. SWPE™ (LLDPE) tube, (not covered by the scope of this approval). Maximum working pressure 10.0 bar. Cold water use only.
Range of tapping tees with gunmetal bodies and plastic fitting, for use with SDR11 & SDR17 Polyethylene barrier pipes (manufactured to BS8588). For pipe diameters between 63mm & 90mm, the adaptor plate must be used. When used with SDR11 pipes the maximum working pressure is 16.0 bar. When used with SDR17 pipes the maximum working pressure is 10.0 bar. Cold water use, for below ground only.
Range of cast iron (blue epoxy coated) (G versions only) or stainless steel (all other versions - F, N, R, T) vertical multistage pumps with stainless steel impellers, shaft and outer sleeve. Maximum working pressures: 16 bar, 25 bar and 40 bar. Oval flanges - Body type ‘T’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 16 bar. Round flanges - Body type ‘R’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 25 bar. Round flanges - Body type ‘F’ (1SV-3SV) - 25 bar. Round flanges - Body type ‘N’ (10SV) - 25 bar. Round flanges - Body type ‘N’ (66SV-92SV) - 16 bar. Round flanges - Body type ‘G’ (33SV, 46SV) - 40 bar. Round flanges - Body type ‘G’ (33SV, 46SV, 66SV-92SV, 125SV) - 16 bar. Round flanges - Body type ‘G’ (125SV) - 25 bar. Cold water use only.
Range of electronic booster pumps with variable speed, incorporating stainless-steel bodies, impellers and shaft, EPDM gaskets and seals and an expansion vessel on the outlet. The pumps incorporate a drain port. Maximum working pressure 10.0 bar. Cold water use only.
Range of circulating pumps, with plastic or stainless steel (cast EN 1.4308) bodies and a plastic impeller. Maximum working pressures: Stainless steel bodied pumps 10.0 bar, Plastic bodied pumps 3.0 bar. Maximum operating temperature 95°C.
Range of shower handsets and shower heads with (plastic bodies - various finishes) Some models incorporate a plastic flow restrictor, or a check valve with built in flow regulator (however, the complete product has not been fully tested to demonstrate it provides backflow protection) or neither (See models for FR or WSCV). Maximum operating temperature 60.0°C Open outlet use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1001450AQXX | various | 1/2" BSP (F) | Open outlet bar | 60 °C | Aqualisa | Body | No | Fixed Head, | |||
| 1001447AQXX | various | 1/2" BSP (F) | Open outlet bar | 60 °C | Aqualisa | Body | No | Fixed Head, | |||
| 1001445AQXX | various | 1/2" BSP (F) | Open outlet bar | 60 °C | Aqualisa | Body | No | Fixed Head, |
Fixed Head in 4 different colours - Chrome, Matt Black, Brushed Brass and Gunmetal Grey AQ = Aqualisa XX = AA , AD , AJ , AH AQAA - Chrome AQAD - Matt Black AQAJ - Gunmetal Grey AQAH - Brushed Brass
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined flexible hose assemblies with DZR brass end connections. Some models incorporate spherical valves. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Ranges of free standing stainless steel cylinders. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C
Range of 2, 3 or 4 way manifolds with brass bodies and stop valves at each of the outlets. Maximum operating pressure 10 bar. Maximum operating temperature 85°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FRM SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| FRM SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| FRM SHCDIV GM | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| FRM SHCDIV BB | BRUSHED BRASS | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
Model added February 2026: RP3 SAI SHCDIV C
Range of wafer or lugged (see models) butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, with Maximum working pressure: 16 Bar. Maximum operating temperature: 100 °C.
Range of spherical valves with nickel-plated brass bodies, chrome plated brass balls, PTFE seat (SD3009 only) and NBR ‘O’-rings. The SD3009 models are screw-driver operated, the SD6011 model incorporate a short lever operating member. The compression connections are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron body and an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
'Novus 30'. Orange coloured, nitrile rubber/aramid fibre gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'BADAMID A70 GF30 HE WL BLACK'. Black coloured, injection moulded, glass fibre ranforced PA66 material. For use with water up to 85°C.
'Ryton XE7730BL'. Black coloured, injection moulded PPSU material. For use with water up to 85°C.
'SQ-30T-W, SQ-40T-W, SQ-50T-W, SQ-60T-W, SQ-70T-W, SQ-80T-W, & SQ-90T-W (transparent, unpigmented)'. ‘SQ-30R-W, SQ-40R-W, SQ-50R-W, SQ-60R-W, SQ-70R-W, SQ-80R-W, & SQ-90R-W (red coloured)'. ‘SQ-30B-W, SQ-40B-W, SQ-50B-W, SQ-60B-W, SQ-70B-W, SQ-80B-W, & SQ-90B (blue coloured)'. Range of compression moulded, silicone rubber materials. Shore hardness between 30 & 90. Tested in-radius size 0.9mm. For use with water up to 85°C:
'PVC Tube Settler Media FS42.50'. Black coloured, extruded PVC 'tube settler' component. For use with water up to 30°C.
A dual layered shower hose with a black silicone outer and a clear silicone inner-liner, incorporating NBR gaskets. Maximum operating temperature 60°C. Open outlet use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 86005740 | chrome | 1/2 BSP | 10 bar | 75 °C | Triton | on front plate | No | Ceramic cartridge | Not Applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| SH803A | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH803ABB | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH803ABBN | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH803AK | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH804A | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH804ABB | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable | ||
| SH804AK | Various | 3/4” x ½” BSP (M) offset unions or 15mm compression | 10 bar | 85 °C | ALFRED LOGO | Rear of body | No | 1/2 Turn ceramic disc | Not Applicable |
** denotes finish: No Suffix = Chrome, H = Black, DYB = Matte white, BZ = Perl white painted, HGTS = Red bronze, HTL = Yellow bronze brushed, Q = Bronze, QTSL = Bronze brushed bright, QTS = Bronze brushed matte, STS = Acid copper brushed, SDMGJ = Water plated rose gold, N = Nickel brushed bright light, NP = Nickel brushed, TJ = Titanium gold, TJLS = Titanium gold brushed, G = Gold, GJS = Gold brushed, GJSY = Zirconium gold wire drawing matte, PGJFY = Zirconium gold wire drawing matte bright light, PLSJ = Brushed gold, LSJY = Brushed gold matte, MGJ = Rose gold, MGJL = Rose gold brushed, DMGJ = Light rose gold brushed, HTS = Red bronze brushed, QHP = Grey, LSQH = Grey brushed, LHMGJ = Brushed yellow rose gold.
Page 3 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
