‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-01'. Factory applied, grey coloured, Portland cement mortar. Mix sand, cement and water in a weight ratio of 1:1:0.35 and apply as per manufacturer's user instructions 'doc: Ascent-01', 'vision: A08052023', dated '2023-05-08'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'RBM PE40 potable water pipe'. Black coloured (with blue external stripes), extruded LDPE pipe. For use with water up to 23°C.
'LLFA® Compression Tape'. Red coloured (with white stripe), silicone based tape, manufactured by extrusion. Shore hardness 55. Tested in-radius 0.4mm. Apply as per manufacturer's instructions 'LLFA® Compression Tape User Guide Rev. 2; July 1, 2017'. For use with water up to 75°C.
'Buffalo PUR500'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '14/08/2018'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Mungo Injection System MIT800RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'Jun-23'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'334701 - EPDM peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted single hole, single outlet (fixed), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure - 10 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Spring loaded resilient trim check valve cartridge with stainless steel spring and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar. BS6920 at 85°C
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Range of ceramic cartridge headworks with plastic bodies, incorporating silicon and NBR‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR seals and O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar or 10.0 Bar (see models) Maximum operating temperature 65.0°C or 85.0°C (see models)
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a sequential headwork controlling both flow and temperature with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 85°C.
Wall mounted single hole, single outlet (fixed) combination tap assembly, brass body(various finishes), incorporating a detent headwork that controls both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator. The product also incorporates a permanently open waste outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The 48 000 xxx model is supplied with a pop-up waste. The 48 001 xxx and 48 002 xxx models are supplied with an open waste/non-closing waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single-hole, single outlet, fixed, combination tap assembly with (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type pop-up waste. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two hole, single outlet (fixed) combination tap assemblies (chrome or matte black plated brass) incorporating quarter turn ceramic disc headworks with single lever operating member. The spout outlet incorporates a plastic aerator. This product is supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, two hole combination tap assembly incorporating ceramic cartridge headwork with single lever operating members. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of wall mounted two-hole, single outlet (fixed) comination tap assemblies with brass bodies (chromium plated), ceramic cartridge headworks and single lever operating members. Spout outlets incorporate plastic aerators. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of two-hole, single outlet fixed combination tap assemblies (brass bodies - various finishes, see model), incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. BS6920 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The spout outlets incorporate a plastic aerator or flow straightener. The products are supplied with a shower hose and handset. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal back nuts, shower hose and handset. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted two-hole, single outlet (fixed) combination tap assembly, (brass body - various finishes) incorporating a ceramic cartridge with single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Wall mounted two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate a plastic flow straightener, and the product is supplied with a single check valve cartridge on the shower outlet (however, the complete product has not been fully tested to demonstrate it provides adequate backflow protection). Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, three-hole single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic flow straightener or aerator. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of four-hole, single outlet, fixed combination tap assemblies in chromium plated or matt black finished brass. Incorporating quarter ceramic disc headworks with single lever operating members. This product also incorporates a manual diverter to a shower outlet. The spout outlets incorporate a plastic aerators. Supplied with stainless steel braided PEX lined flex hose assemblies for connecting the spout and headworks. Not supplied with shower hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted spout outlet, (brass body - various finishes) incorporating a plastic flow straightener. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range on inline filter cartridges incorporating plastic bodies. The filter media varies between models and includes active carbon, silver impregnated active carbon, silver carbon block & weak/strong cationic resin. Maximum working pressure 6.0 bar. Cold water use only.
‘F18’ range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with Rifeng B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of brass press fittings (TH and U crimp profiles) with EPDM ‘O’-rings for use with RIIFO B1 PEX/AL/PEX multilayer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
Range of ‘Henco Profit Synthetic’ pushfit fittings with PPS (HPK models) or brass (HP models) bodies and EPDM o-rings, to be used with ‘Henco RIXc’ PEXc/Al/PEXc multilayer pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of MM and MC press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with AIS XPERT multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Range of brass (Series 1000 & 1100) and DZR brass (Series 1100CZ) compression fittings, various finishes. For use with copper tube EN1057. Maximum working pressure 30.0 bar. Maximum operating temperature 100°C.
Page 66 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
