Section:

0650 Combination Tap Assemblies

Description:

A Range of Three hole tap(s) with a single outlet and a fixed spout.

Wall Mounted Undefinable Air Gap – See IRN’s

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

31/08/2030

Notes & Further Information

Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish Products need to be installed in combination with basic set 10303180.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturers:

Hansgrohe SE

Range of three-hole, single outlet, combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up or lever type waste – not verified by test. Maximum working pressure. 6.0 bar. Maximum operating temperature 65°C.

Section:

0650 Combination Tap Assemblies

Section Subtitle:

Three hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

250902013

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

WATERWORKS on escutcheon or end of spout.

Installation Requirements:

R001 R006 R008 R010

Expiry date:

30/09/2030

Model:

BLS2ZZX BLS6ZZX CLS2ZZX HLS2ZZX Followed by the legend of the type of lever/handle and surface finish. Suffix options: ZZ = represents handle components 0 Less Handles 1 Cross Handle 2 Two‐Tone Cross Handle 3 Coin Edge Cross Handle 10 Solo Series Lever Handle 11 Lever Handle 12 Two‐Tone Lever Handle 13 Coin Edge Lever Handle 14 Walnut Lever Handle 15 Leather Lever Handle 20 Solo Series Straight Lever Handle 2A Tandem Series Guilloche Lines Lever Handle 2B Tandem Series Two‐Tone Lever Handle 2C Union Series Guilloche Link Lever Handle 2D Union Series Enamel Guilloche Lines Lever Handle 2E Union Series Guilloche Pinstripe Lever Handle 2P Solo Series Two‐Piece Straight Lever Handle 2S Bond Rally Series Lever Handle 2T Teak Lever Handle 30 Solo Series Knob Handle 3S Bond Rally Series Knob Handle 4A Tandem Series Guilloche Lines Knob Handle 4B Tandem Series Two‐Tone Guilloche Knob Handle 4D Union Series Enamel Guilloche Lines Knob Handle 5C Union Series Guilloche Link Knob Handle 7A Tandem Series Guiloche Lines Lever handles with Gland Cover 7B Tandem Series Two Tone Lever handles with Gland Cover 7C Union Series Guiloche Link Lever handles with Gland Cover 7D Union Series Enamel Guiloche Lines Lever handles with Gland Cover 7E Union Series Guiloche Pinstripe Lever handles with Gland Cover 7P Solo Series Two Piece Straight Lever handle with Gland Cover 7S Bond Rally Series Lever Handle with Gland Cover 7T Tandem Series Teak lever with Gland Cover 8Z Straight Lever Handle 90 Solo Series Straight Lever handles with Gland Cover X = represents External Color or Finish Options AC Antique Copper AB Architectural Bronze AQB Antique Brass BZ Architectural Bronze C Polished Chrome CO Concordia DN Dark Nickel G Gold L Lumin M Matte Nickel MC Matte Chrome MG Matte Gold MS Matte Silver N Polished Nickel S Silver SC Shiny Copper SO Sovereign UB Unlacquered Brass

Approval Holder:

Waterworks

Company Name

Waterworks

Address

10 John Street London WC1N2EB

View All Listings by this Company

Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headwork with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.

Section:

0650 Combination Tap Assemblies

Section Subtitle:

Three hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

250902014

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

WATERWORKS on rear or on edge of spout outlet.

Installation Requirements:

R001 R006 R008 R010

Expiry date:

30/09/2030

Model:

CLS1ZZX HLS1ZZX BLS5XXZ Suffix Options: ZZ = represents handle components 0 Less Handles 1 Cross Handle 2 Two‐Tone Cross Handle 3 Coin Edge Cross Handle 10 Solo Series Lever Handle 11 Lever Handle 12 Two‐Tone Lever Handle 13 Coin Edge Lever Handle 14 Walnut Lever Handle 15 Leather Lever Handle 20 Solo Series Straight Lever Handle 2A Tandem Series Guilloche Lines Lever Handle 2B Tandem Series Two‐Tone Lever Handle 2C Union Series Guilloche Link Lever Handle 2D Union Series Enamel Guilloche Lines Lever Handle 2E Union Series Guilloche Pinstripe Lever Handle 2P Solo Series Two‐Piece Straight Lever Handle 2S Bond Rally Series Lever Handle 2T Teak Lever Handle 30 Solo Series Knob Handle 3S Bond Rally Series Knob Handle 4A Tandem Series Guilloche Lines Knob Handle 4B Tandem Series Two‐Tone Guilloche Knob Handle 4D Union Series Enamel Guilloche Lines Knob Handle 5C Union Series Guilloche Link Knob Handle 7A Tandem Series Guiloche Lines Lever handles with Gland Cover 7B Tandem Series Two Tone Lever handles with Gland Cover 7C Union Series Guiloche Link Lever handles with Gland Cover 7D Union Series Enamel Guiloche Lines Lever handles with Gland Cover 7E Union Series Guiloche Pinstripe Lever handles with Gland Cover 7P Solo Series Two Piece Straight Lever handle with Gland Cover 7S Bond Rally Series Lever Handle With Gland Cover 7T Tandem Series Teak lever with Gland Cover 8Z Straight Lever Handle 90 Solo Series Straight Lever handles with Gland Cover X = represents External Color or Finish Options AC Antique Copper AB Architectural Bronze AQB Antique Brass BZ Architectural Bronze C Polished Chrome CO Concordia DN Dark Nickel G Gold L Lumin M Matte Nickel MC Matte Chrome MG Matte Gold MS Matte Silver N Polished Nickel S Silver SC Shiny Copper SO Sovereign UB Unlacquered Brass

Approval Holder:

Waterworks

Company Name

Waterworks

Address

10 John Street London WC1N2EB

View All Listings by this Company

Range of three-hole, metal, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste – not verified by test. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.

Section:

0650 Combination Tap Assemblies

Section Subtitle:

Three hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

250902015

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

WATERWORKS on rear of body and on adhesive label on rear of body or WATERWORKS on edge of spout.

Installation Requirements:

R001 R006 R008 R010

Expiry date:

30/09/2030

Model:

BLS1ZZX 8 Suffix Options: ZZ = represents handle components 0 Less Handles 1 Cross Handle 2 Two‐Tone Cross Handle 3 Coin Edge Cross Handle 10 Solo Series Lever Handle 11 Lever Handle 12 Two‐Tone Lever Handle 13 Coin Edge Lever Handle 14 Walnut Lever Handle 15 Leather Lever Handle 20 Solo Series Straight Lever Handle 2A Tandem Series Guilloche Lines Lever Handle 2B Tandem Series Two‐Tone Lever Handle 2C Union Series Guilloche Link Lever Handle 2D Union Series Enamel Guilloche Lines Lever Handle 2E Union Series Guilloche Pinstripe Lever Handle 2P Solo Series Two‐Piece Straight Lever Handle 2S Bond Rally Series Lever Handle 2T Teak Lever Handle 30 Solo Series Knob Handle 3S Bond Rally Series Knob Handle 4A Tandem Series Guilloche Lines Knob Handle 4B Tandem Series Two‐Tone Guilloche Knob Handle 4D Union Series Enamel Guilloche Lines Knob Handle 5C Union Series Guilloche Link Knob Handle 7A Tandem Series Guiloche Lines Lever handles with Gland Cover 7B Tandem Series Two Tone Lever handles with Gland Cover 7C Union Series Guiloche Link Lever handles with Gland Cover 7D Union Series Enamel Guiloche Lines Lever handles with Gland Cover 7E Union Series Guiloche Pinstripe Lever handles with Gland Cover 7P Solo Series Two Piece Straight Lever handle with Gland Cover 7S Bond Rally Series Lever Handle With Gland Cover 7T Tandem Series Teak lever with Gland Cover 8Z Straight Lever Handle 90 Solo Series Straight Lever handles with Gland Cover X = represents External Color or Finish Options AC Antique Copper AB Architectural Bronze AQB Antique Brass BZ Architectural Bronze C Polished Chrome CO Concordia DN Dark Nickel G Gold L Lumin M Matte Nickel MC Matte Chrome MG Matte Gold MS Matte Silver N Polished Nickel S Silver SC Shiny Copper SO Sovereign UB Unlacquered Brass

Approval Holder:

Waterworks

Company Name

Waterworks

Address

10 John Street London WC1N2EB

View All Listings by this Company

Section:

0650 Combination Tap Assemblies

Description:

A Three hole tap(s) with a single outlet and a fixed spout.

Deck mounted Capable of achieving AUK3 Tap gap Stainless steel braided PEX lined Inlet Hose Stainless steel braided PEX lined connection Hose

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R010

Expiry date:

30/09/2030

Notes & Further Information

* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black

Approval Holder:

WINSDRUM Technology (Foshan) Co., Ltd

Company Name

WINSDRUM Technology (Foshan) Co., Ltd

Address

Room 804-805, Flat 2, Jiabang Guojin Center, No.1 Shilong South Road, Guicheng Street, Nanhai District, Foshan City, Guangdong Province

Country

China

Phone

0086-19527590441

General Email

carina07@126.com

View All Listings by this Company

Range of free-standing sanitary macerating disposal units. The units are fed via a flexible hose assembly. Flow is controlled by a solenoid valve and discharges via a type `AB` air gap (verified by test, suitable of fluid category 5 backflow protection). Maximum working pressure 6.0 Bar Maximum operating temperature 40.0°C

Section:

0950 Disposal Unit(s)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

PVC hose with 3/4" BSP captive nut end connections.

Marking:

DDC and Pulpmatic flex on front of unit body

Installation Requirements:

R001 R574

Expiry date:

30/09/2030

Model:

FLX000-50HZ 240V - Pulpmatic Flex Macerator FLX000-60HZ 110V - Pulpmatic Flex Macerator UL

Manufacturer:

DDC Dolphin Ltd.

Company Name

DDC Dolphin Ltd.

Address

The Fulcrum, Vantage Way, Poole

Postcode

BH12 4NU

Country

Dorset,

Phone

+44 (0)1202 724858

View All Listings by this Company

Range of monochloramine generators incorporating UPVC pipework, fittings and an external flow sensor. Maximum working pressure 6.0 bar. Cold water use only.

Section:

0970 Dosing Equipment

Section Subtitle:

Fittings in this section have been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which they have been designed

WRAS Approval Number:

250302705

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP F

Marking:

Sanikill Tec on adhesive label on body

Installation Requirements:

R001 R008 R415 R575

Expiry date:

31/03/2030

Model:

ESKUT-LT1002 SANIKILL Tec 500 g. ESKUT-LT2004 SANIKILL Tec 1 kg.

Approval Holder:

Sanipur S.p.A.

Company Name

Sanipur S.p.A.

Address

Via S. Quasimodo,25 25020 Flero (BS)

Country

Italy

General Email

b.fermi@sanipur.it

View All Listings by this Company

Range of cylindrical or tubular expansion vessels with epoxy coated carbon steel bodies. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C

Section:

1000 Expansion Vessels

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” or 1” BSP (M)

Marking:

Trade-Tec, size in L and technical information on adhesive label

Installation Requirements:

R001 R530

Expiry date:

30/06/2029

Model:

TRPVES08 TRPVES12 TRPVES19 TRPVES24 TRPVES35 TRPVES50 TRPVES80 TRPVES100

Approval Holder:

Intatec Limited

Company Name

Intatec Limited

Address

Airfield Industrial Estate Hixon Staffordshire

Postcode

ST18 0PF

Country

United Kingdom

Phone

01889272180

General Email

ryan.tilsley@intatec.co.uk

View All Listings by this Company

Range of filling loop assemblies consisting of an in-line isolation valve, an in-line double check valve assembly (suitable for back flow protection against fluid category 3) that incorporates an isolation valve and a stainless-steel braided EPDM lined hose. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Non-metallic materials and components comply with BS6920 at 85°C

Section:

1015 Filling Loop

Size:

15mm compression or 15mm pushfit.

Marking:

Altecnic logo, flow arrow and CR on valve. Altecnic, WRAS and date of manufacture (YYYY) on hose.

Installation Requirements:

R001

Expiry date:

28/02/2029

Model:

521726, 941192.

Approval Holder:

City Plumbing

Company Name

City Plumbing

Address

Highbourne House, 1 Eldon Way, Crick, Northamptonshire

Postcode

NN6 7SL

View All Listings by this Company

Manufacturer:

Altecnic Limited

Company Name

Altecnic Limited

Address

Francesco House, Staples Close Stafford Staffordshire

Postcode

ST16 1WQ

Country

United Kingdom

Phone

+44 (0)1785 218200

View All Listings by this Company

Manufacturer:

Altecnic Limited

Company Name

Altecnic Limited

Address

Francesco House, Staples Close Stafford Staffordshire

Postcode

ST16 1WQ

Country

United Kingdom

Phone

+44 (0)1785 218200

View All Listings by this Company

Inline filter with plastic body. Maximum working pressure 5.0 bar. Cold water use only.

Section:

1050 Filters and Housings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8" BSP (F)

Marking:

Alfred Victoria "crown" logo on body

Installation Requirements:

R001 R008 R120 R150 R170

Expiry date:

31/12/2029

Model:

FIL04

Approval Holder:

ALFRED VICTORIA LIMITED

Company Name

ALFRED VICTORIA LIMITED

Postcode

B45 9AL

Country

United Kingdom

Phone

00441213592214

General Email

daisy.qin@alfredvictoria.co.uk

View All Listings by this Company

Range of stainless-steel(SS304L) press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250604033

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

MTF, model number, Size on fitting

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

Coupling GDC5001 OD15 GDC5002 OD18 GDC5003 OD22 GDC5004 OD28 GDC5005 OD35 GDC5006 OD42 GDC5007 OD54 GDC6501 OD66.7 GDC5008 OD76.1 GDC5009 OD88.9 GDC5010 OD108 Long Coupling GDC5011 OD15 GDC5012 OD18 GDC5013 OD22 GDC5014 OD28 GDC5015 OD35 GDC5016 OD42 GDC5017 OD54 GDC6502 OD66.7 GDC5018 OD76.1 GDC5019 OD88.9 GDC5020 OD108 Reducer with Plain End GDC5021 OD18×OD15 GDC5022 OD22×OD15 GDC5023 OD22×OD18 GDC5024 OD28×OD15 GDC5025 OD28×OD18 GDC5026 OD28×OD22 GDC5048 OD35×OD15 GDC5027 OD35×OD18 GDC5029 OD35×OD22 GDC5030 OD35×OD28 GDC5031 OD42×OD15 GDC5032 OD42×OD18 GDC5033 OD42×OD22 GDC5034 OD42×OD28 GDC5035 OD42×OD35 GDC5036 OD54×OD15 GDC5037 OD54×OD18 GDC5038 OD54×OD22 GDC5039 OD54×OD28 GDC5040 OD54×OD35 GDC5041 OD54×OD42 GDC6503 OD66.7×OD42 GDC6504 OD66.7×OD54 GDC5028 OD76.1×OD42 GDC5042 OD76.1×OD54 GDC6505 OD76.1×OD66.7 GDC5049 OD88.9×OD42 GDC5043 OD88.9×OD54 GDC6506 OD88.9×OD66.7 GDC5044 OD88.9×OD76.1 GDC5045 OD108×OD54 GDC6507 OD108×OD66.7 GDC5046 OD108×OD76.1 GDC5047 OD108×OD88.9 90° Elbow GDC6051 OD15 GDC6052 OD18 GDC6053 OD22 GDC6054 OD28 GDC6055 OD35 GDC6056 OD42 GDC6057 OD54 GDC6511 OD66.7 GDC6058 OD76.1 GDC6059 OD88.9 GDC6060 OD108 90° Elbow with Plain End GDC6071 OD15 GDC6072 OD18 GDC6073 OD22 GDC6074 OD28 GDC6075 OD35 GDC6076 OD42 GDC6077 OD54 GDC6512 OD66.7 GDC6078 OD76.1 GDC6079 OD88.9 GDC6080 OD108 45° Elbow GDC6101 OD15 GDC6102 OD18 GDC6103 OD22 GDC6104 OD28 GDC6105 OD35 GDC6106 OD42 GDC6107 OD54 GDC6513 OD66.7 GDC6108 OD76.1 GDC6109 OD88.9 GDC6110 OD108 45° Elbow with Plain End GDC6121 OD15 GDC6122 OD18 GDC6123 OD22 GDC6124 OD28 GDC6125 OD35 GDC6126 OD42 GDC6127 OD54 GDC6514 OD66.7 GDC6128 OD76.1 GDC6129 OD88.9 GDC6130 OD108 Tee GDC5181 OD15 GDC5182 OD18 GDC5183 OD22 GDC5184 OD28 GDC5185 OD35 GDC5186 OD42 GDC5187 OD54 GDC6515 OD66.7 GDC5188 OD76.1 GDC5189 OD88.9 GDC5190 OD108 Reducing Tee GDC5191 OD18×OD15 GDC5192 OD22×OD15 GDC5193 OD22×OD18 GDC5194 OD28×OD15 GDC5195 OD28×OD18 GDC5196 OD28×OD22 GDC5197 OD35×OD15 GDC5198 OD35×OD18 GDC5199 OD35×OD22 GDC5200 OD35×OD28 GDC5201 OD42×OD15 GDC5202 OD42×OD18 GDC5203 OD42×OD22 GDC5204 OD42×OD28 GDC5205 OD42×OD35 GDC5206 OD54×OD15 GDC5207 OD54×OD18 GDC5208 OD54×OD22 GDC5209 OD54×OD28 GDC5210 OD54×OD35 GDC5211 OD54×OD42 GDC6517 OD66.7×OD22 GDC6518 OD66.7×OD28 GDC6519 OD66.7×OD35 GDC6520 OD66.7×OD42 GDC6521 OD66.7×OD54 GDC5212 OD76.1×OD22 GDC5213 OD76.1×OD28 GDC5214 OD76.1×OD35 GDC5215 OD76.1×OD42 GDC5216 OD76.1×OD54 GDC6522 OD76.1×OD66.7 GDC5217 OD88.9×OD22 GDC5218 OD88.9×OD28 GDC5219 OD88.9×OD35 GDC5220 OD88.9×OD42 GDC5221 OD88.9×OD54 GDC6523 OD88.9×OD66.7 GDC5222 OD88.9×OD76.1 GDC5223 OD108×OD22 GDC5224 OD108×OD28 GDC5225 OD108×OD35 GDC5226 OD108×OD42 GDC5227 OD108×OD54 GDC6524 OD108×OD66.7 GDC5228 OD108×OD76.1 GDC5229 OD108×OD88.9 Tee with Male Thread End GDC5231 OD15×R1/2 GDC5232 OD18×R1/2 GDC5239 OD22×R1/2 GDC5233 OD22×R3/4 GDC5234 OD22×R1 GDC5240 OD28×R1/2 GDC5283 OD28×R3/4 GDC5235 OD28×R1 GDC5281 OD35×Rp3/4 GDC5236 OD35×Rp1 1/4 GDC5237 OD42×Rp1 1/2 GDC5282 OD54×Rp1/2 GDC5238 OD54×Rp2 Tee with Female Thread End GDC5241 OD15×Rp1/2 GDC5242 OD18×Rp1/2 GDC5243 OD18×Rp3/4 GDC5244 OD22×Rp1/2 GDC5245 OD22×Rp3/4 GDC5246 OD28×Rp1/2 GDC5247 OD28×Rp3/4 GDC5248 OD28×Rp1 GDC5249 OD35×Rp1/2 GDC5250 OD35×Rp3/4 GDC5262 OD35×Rp1 GDC5263 OD35×Rp1 1/4 GDC5251 OD42×Rp1/2 GDC5252 OD42×Rp3/4 GDC5264 OD42×Rp1 GDC5265 OD42×Rp1 1/2 GDC5253 OD54×Rp1/2 GDC5254 OD54×Rp3/4 GDC5266 OD54×Rp1 GDC5255 OD54×Rp2 GDC6531 OD66.7×Rp1/2 GDC6532 OD66.7×Rp3/4 GDC6533 OD66.7×Rp1 1/2 GDC5256 OD76.1×Rp3/4 GDC5257 OD76.1×Rp2 GDC5258 OD88.9×Rp3/4 GDC5259 OD88.9×Rp2 GDC5260 OD108×Rp3/4 GDC5261 OD108×Rp2 Adaptor with Male Thread End GDC5360 OD15×R3/8 GDC5361 OD15×R1/2 GDC5362 OD15×R3/4 GDC5363 OD18×R1/2 GDC5364 OD18×R3/4 GDC5365 OD22×R1/2 GDC5366 OD22×R3/4 GDC5367 OD22×R1 GDC5368 OD28×R3/4 GDC5369 OD28×R1 GDC5370 OD28×R1 1/4 GDC5371 OD35×R1 GDC5372 OD35×R1 1/4 GDC5373 OD35×R1 1/2 GDC5374 OD42×R1 1/4 GDC5375 OD42×R1 1/2 GDC5376 OD54×R1 1/2 GDC5377 OD54×R2 GDC6541 OD66.7×R2 1/2 GDC5378 OD76.1×R2 1/2 GDC5379 OD88.9×R3 GDC5380 OD108×R4 Adaptor with Female Thread End GDC5381 OD15×Rp1/2 GDC5382 OD15×Rp3/4 GDC5383 OD18×Rp1/2 GDC5384 OD18×Rp3/4 GDC5385 OD22×Rp1/2 GDC5386 OD22×Rp3/4 GDC5387 OD22×Rp1 GDC5388 OD28×Rp3/4 GDC5389 OD28×Rp1 GDC5390 OD28×Rp1 1/4 GDC5391 OD35×Rp1 GDC5392 OD35×Rp1 1/4 GDC5393 OD35×Rp1 1/2 GDC5394 OD42×Rp1 1/4 GDC5395 OD42×Rp1 1/2 GDC5396 OD54×Rp1 1/2 GDC5397 OD54×Rp2 GDC6542 OD66.7×Rp2 1/2 GDC5398 OD76.1×Rp2 1/2 GDC5399 OD88.9×Rp3 GDC5400 OD108×Rp4 Cap GDC5421 OD15 GDC5422 OD18 GDC5423 OD22 GDC5424 OD28 GDC5425 OD35 GDC5426 OD42 GDC5427 OD54 GDC6542 OD66.7 GDC5428 OD76.1 GDC5429 OD88.9 GDC5430 OD108 Adaptor with Union Nut GDC5341 OD15×G1/2 GDC5353 OD15×G3/4 GDC5342 OD18×G1/2 GDC5343 OD18×G3/4 GDC5345 OD22×G1 GDC5347 OD28×G1 GDC5348 OD28×G1 1/4 GDC5359 OD35×G1 1/4 GDC5350 OD35×G1 1/2 GDC5351 OD42×G1 3/4 GDC5346 OD42×G1 1/2 GDC5356 OD54×G2 GDC5352 OD54×G2 3/8 Adaptor with Union with Female thread GDC5451 OD15×Rp1/2 GDC5452 OD15×Rp3/4 GDC5453 OD18×Rp1/2 GDC5454 OD18×Rp3/4 GDC5455 OD22×Rp3/4 GDC5456 OD22×Rp1 GDC5457 OD28×Rp1 GDC5458 OD35×Rp1 1/4 GDC5459 OD42×Rp1 1/2 GDC5460 OD54×Rp2 Adaptor Union with Male Thread GDC5431 OD15×R1/2 GDC5432 OD15×R3/4 GDC5433 OD18×R1/2 GDC5434 OD18×R3/4 GDC5435 OD22×R1/2 GDC5436 OD22×R3/4 GDC5437 OD22×R1 GDC5438 OD28×R1 GDC5439 OD35×R1 1/4 GDC5440 OD42×R1 1/2 GDC5441 OD54×R2 Adaptor Union GDC5471 OD15 GDC5472 OD18 GDC5473 OD22 GDC5474 OD28 GDC5475 OD35 GDC5476 OD42 GDC5477 OD54 Flange with Pressing Socket GDC5301 OD15 GDC5302 OD18 GDC5303 OD22 GDC5304 OD28 GDC5305 OD35 GDC5306 OD42 GDC5307 OD54 GDC6536 OD66.7 GDC5308 OD76.1 GDC5309 OD88.9 GDC5310 OD108

Approval Holder:

Marla Tube Fittings Limited

Company Name

Marla Tube Fittings Limited

Address

Kinwarton Farm Road Alcester

Postcode

B49 6EH

Country

United Kingdom

Phone

01789 761207

General Email

graham.walker@marla.co.uk

View All Listings by this Company

Range of green Sappro butt-welded polypropylene fittings for use with Sappro PPR pipes. Maximum working pressure: 20 Bar. Maximum operating temperature: 23°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250802006

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Sappro logo and size on body. Sappro logo, ISO 15874-2 and size on pipe body

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

Pipe: SFP6285205000015 20 mm SFP6285205000022 25 mm SFP6285205000039 32 mm SFP6285205000046 40 mm SFP6285205000053 50 mm SFP6285205000060 63 mm SFP6285205000077 75 mm SFP6285205000084 90 mm Elbow 90°: SFP6285205002613 20 mm SFP6285205002620 25 mm SFP6285205002637 32 mm SFP6285205002644 40 mm SFP6285205002651 50 mm SFP6285205002668 63 mm SFP6285205002675 75 mm SFP6285205002682 90 mm Elbow 45°: SFP6285205002798 20 mm SFP6285205002804 25 mm SFP6285205002811 32 mm SFP6285205003030 40 mm SFP6285205003047 50 mm SFP6285205003054 63 mm SFP6285205003061 75 mm SFP6285205003078 90 mm Equal Tee: SFP6285205003566 20 mm SFP6285205003573 25 mm SFP6285205003580 32 mm SFP6285205003597 40 mm SFP6285205003603 50 mm SFP6285205003610 63 mm SFP6285205003627 75 mm SFP6285205003634 90 mm Socket: SFP6285205003221 20 mm SFP6285205003238 25 mm SFP6285205003245 32 mm SFP6285205003252 40 mm SFP6285205003269 50 mm SFP6285205003276 63 mm SFP6285205003283 75 mm SFP6285205003290 90 mm Bridge Bend: SFP6285205001593 20mm SFP6285205001609 25mm SFP6285205001616 32mm Socket Bridge Bend: SFP6285205002033 25mm End Cap: SFP6285205003740 20mm SFP6285205003962 25mm SFP6285205003979 32mm SFP6285205003986 40mm SFP6285205003993 50mm SFP6285205004006 63mm SFP6285205004013 75mm SFP6285205004020 90mm Male Plug: SFP6285205004136 20mm Reducer Socket: SFP6285205007267 25mm x 20mm SFP6285205007281 32mm x 25mm SFP6285205007274 32mm x 20mm SFP6285205007304 40mm x 25mm SFP6285205007311 40mm x 32mm SFP6285205007313 50mm x 25mm SFP6285205007314 50mm x 32mm SFP6285205007315 50mm x 40mm SFP6285205007317 63mm x 25mm SFP6285205007318 63mm x 32mm SFP6285205007319 63mm x 40mm SFP6285205007320 63mm x 50mm Reducer: SFP6285205005331 75mm x 32mm SFP6285205005348 75mm x 40mm SFP6285205005355 75mm x 50mm SFP6285205005362 75mm x 63mm Reducer Tee: SFP6285205005911 25mm x 20mm SFP6285205006208 32mm x 25mm SFP6285205006222 40mm x 25mm SFP6285205006239 40mm x 32mm SFP6285205006604 50mm x 25mm SFP6285205006628 50mm x 32mm SFP6285205006642 63mm x 25mm SFP6285205006666 63mm x 32mm SFP6285205006673 63mm x 40mm SFP6285205006697 75mm x 32mm SFP6285205006703 75mm x 40mm SFP6285205006710 75mm x 50mm SFP6285205006727 75mm x 63mm Female Socket: SFP6285205007625 20mm x 1/2" BSP (F) SFP6285205007626 20mm x 3/4" BSP (F) SFP6285205007627 25mm x 1/2" BSP (F) SFP6285205007628 25mm x 3/4" BSP (F) SFP6285205007629 32mm x 1/2" BSP (F) SFP6285205007630 32mm x 3/4" BSP (F) SFP6285205007631 32mm x 1" BSP (F) Male Socket: SFP6285205007660 20mm x 1/2" BSP (M) SFP6285205007661 20mm x 3/4" BSP (M) SFP6285205007662 25mm x 1/2" BSP (M) SFP6285205007663 25mm x 3/4" BSP (M) SFP6285205007664 32mm x 1/2" BSP (M) SFP6285205007665 32mm x 3/4" BSP (M) Female Double Tee: SFP6285205007458 25mm x 1/2" BSP (F) Female Elbow: SFP6285205008039 20mm x 1/2" BSP (F) SFP6285205008041 25mm x 1/2" BSP (F) SFP6285205008042 25mm x 3/4" BSP (F) SFP6285205008043 32mm x 1/2" BSP (F) SFP6285205008044 32mm x 3/4" BSP (F) SFP6285205008045 32mm x 1" BSP (F) Male Elbow: SFP6285205008055 25mm x 1/2" BSP (M) SFP6285205008056 25mm x 3/4" BSP (M) SFP6285205008058 32mm x 1" BSP (M) Male Hexagon: SFP6285205008025 32mm x 1" BSP (M) SFP6285205008027 40mm x 1 1/4" BSP (M) SFP6285205008028 50mm x 1 1/2" BSP (M) SFP6285205008029 63mm x 2" BSP (M) SFP6285205008030 75mm x 2 1/2" BSP (M) SFP6285205008031 90mm x 3" BSP (M) Female Tee: SFP6285205007599 25mm x 1/2" BSP (F) SFP6285205007600 25mm x 3/4" BSP (F) SFP6285205007601 32mm x 1/2" BSP (F) SFP6285205007602 32mm x 3/4" BSP (F) SFP6285205007603 32mm x 1" BSP (F)

Approval Holder:

SAUDI FACTORY CO, FOR PLASTIC PRODUCTS

Company Name

SAUDI FACTORY CO, FOR PLASTIC PRODUCTS

Address

Albjadiya Industrial RIYADH

Country

Saudi Arabia

View All Listings by this Company

U Profile range of press fittings incorporating EPDM ‘O’-rings. For use with Mingshi (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2304383

Size:

16-32mm. BSP threaded connections: ½” - 1½” (M) or (F).

Marking:

Fitting: Mingshi and size on body. Pipe: Mingshi, Mingshi logo, WRAS, size, length, temperature, pressure, date of manufacture (DD/MM/YYYY) and ISO standard on pipe.

Installation Requirements:

R001

Expiry date:

30/04/2028

Model:

Straight: PS16X16 PS20X20 PS25X25 PS32X32 Reduced straight: PS20X16 PS25X16 PS25X20 PS32X16 PS32X20 PS32X25 Male straight: PS16X1/2M PS16X3/4M PS20X1/2M PS20X3/4M PS20x1M PS25x1/2M PS25X3/4M PS25X1M PS32x1/2M PS32X3/4M PS32X1M PS32x11/4M PS32x11/2M Female straight: PS16X1/2F PS16X3/4F PS16X1F PS20X1/2F PS20X3/4F PS20x1F PS25X1/2F PS25X3/4F PS25X1F PS32x1/2F PS32X3/4F PS32X1F PS32X11/4F PS32x11/2F Elbow: PL16X16 PL20X20 PL25x25 PL32X32 Male elbow: PL16X1/2M PL16X3/4M PL20X1/2M PL20X3/4M PL20x1M PL25X1/2M PL25X3/4M PL25X1M PL32x1/2M PL32x3/4M PL32X1M PL32x11/4M Female elbow: PL16X1/2F PL16X3/4F PL20X1/2F PL20X3/4F PL20x1F PS25X1/2F PS25X3/4F PS25X1F PL32x1/2F PS32X3/4F PS32X1F PL32x11/4F Wall plated elbow: PZL16X1/2F PZL16x3/4F PZL20X1/2F PZL20X3/4F Tee: PT16X16X16 PT20X20X20 PT25X25X25 PT32X32X32 Reduced tee: PT16X20X16 PT16X25X16 PT20X16X20 PT20X25X20 PT25X16X25 PT25X16X16 PT25X20X25 PT25X32X25 PT32X16X32 PT32X20X32 PT32X25X32 PT25x16x20 PT32x20x25 PT32x20x26 PT20X16X16 PT20X20X16 PT25X25X20 PT25X20X20 PT25x16x20 PT32x20x25 PT32x32x16 PT32x32x20 PT32x25x25 Male tee: PT16X1/2MX16 PT16x3/4Mx16 PT20X1/2MX20 PT20X3/4MX20 Female tee: PT16X1/2FX16 PT16X3/4FX16 PT20X1/2FX20 PT20X3/4FX20 PT20X1FX20 PT25X1/2FX25 PT25X3/4FX25 PT25X1FX25 32X1/2FX32 PT32X3/4FX32 PT32X1FX32 PT32X11/4FX32 Cap: PSE16 PSE20 PSE25 PSE32 Female union: PS16X1/2F-H PS16X3/4F-H PS20X1/2F-H PS20X3/4F-H PS25X1/2F-H PS25X3/4F-H PS25X1F-H PS32X1F-H Pipe: ALPEX162 ALPEX202 ALPEX252 ALPEX323

Approval Holder:

Pedarson LTD

Company Name

Pedarson LTD

Address

Unit 16 Martlesham Creek Ind Est Sandy Lane Woodbridge Suffolk

Postcode

IP12 4SD

Country

United Kingdom

Phone

01394384077

View All Listings by this Company

F1C compression & F5 press fittings for use with B1 multilayer PEX/AL/PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250406702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

12mm, 16mm, 20mm, 25mm, 26mm & 32mm.

Marking:

Fittings: Rifeng, Size, crimp profile (U), date of manufacture (yyyy/mm), on crimp sleeve. Pipes: Rifeng, PEXb/AL/PEXb, pressure, size, date of manufacture & batch no.

Installation Requirements:

R001

Expiry date:

30/04/2030

Model:

B1 multilayer PEX/AL/PEX pipe, F1C compression fittings & F5 press fittings. Pipe: Multilayer PEX/AL/PEX Pipes B1-0912 Multilayer PEX/AL/PEX Pipes B1-1216 Multilayer PEX/AL/PEX Pipes B1-1620 Multilayer PEX/AL/PEX Pipes B1-2025 Multilayer PEX/AL/PEX Pipes B1-2026 Multilayer PEX/AL/PEX Pipes B1-2632 F5 Equal straight union: F5-S0912*0912 F5-S1216*1216 F5-S1620*1620 F5-S2025*2025 F5-S2026*2026 F5-S2632*2632 F5 Reducer: F5-S1216*0912 F5-S1620*0912 F5-S1620*1216 F5-S2025*0912 F5-S2025*1216 F5-S2025*1620 F5-S2026*0912 F5-S2026*1216 F5-S2026*1620 F5-S2632*0912 F5-S2632*1216 F5-S2632*1620 F5-S2632*2025 F5-S2632*2026 F5 Male straight union: F5-S0912*1/2 F5-S0912*3/4 F5-S1216*3/8 F5-S1216*1/4 F5-S1216*1/2 F5-S1216*3/4 F5-S1216*1 F5-S1620*3/8 F5-S1620*1/2 F5-S1620*3/4 F5-S1620*1 F5-S2025*1/2 F5-S2025*3/4 F5-S2025*1 F5-S2026*1/2 F5-S2026*3/4 F5-S2026*1 F5-S2632*1/2 F5-S2632*3/4 F5-S2632*1 F5-S2632*1 1/4 F5-S2632*1 1/2 F5 Female straight union: F5-S0912*1/2F F5-S0912*3/4F F5-S1216*3/8F F5-S1216*1/4F F5-S1216*1/2F F5-S1216*3/4F F5-S1216*1F F5-S1620*3/8F F5-S1620*1/2F F5-S1620*3/4F F5-S1620*1F F5-S2025*1/2F F5-S2025*3/4F F5-S2025*1F F5-S2026*1/2F F5-S2026*3/4F F5-S2026*1F F5-S2632*1/2F F5-S2632*3/4F F5-S2632*1F F5-S2632*1 1/4F F5-S2632*1 1/2F F5 Equal elbow: F5-L0912*0912 F5-L1216*1216 F5-L1620*1620 F5-L2025*2025 F5-L2026*2026 F5-L2632*2632 F5 Equal elbow (45°): F5-L0912*0912 (45°) F5-L1216*1216 (45°) F5-L1620*1620 (45°) F5-L2025*2025 (45°) F5-L2026*2026 (45°) F5-L2632*2632(45°) F5 Unequal elbow: F5-L1216*0912 F5-L1620*0912 F5-L1620*1216 F5-L2025*0912 F5-L2025*1216 F5-L2025*1620 F5-L2026*0912 F5-L2026*1216 F5-L2026*1620 F5-L2632*0912 F5-L2632*1216 F5-L2632*1620 F5-L2632*2025 F5-L2632*2026 F5 Male elbow: F5-L0912*1/2 F5-L0912*3/4 F5-L1216*3/8 F5-L1216*1/4 F5-L1216*1/2 F5-L1216*3/4 F5-L1216*1 F5-L1620*3/8 F5-L1620*1/2 F5-L1620*3/4 F5-L1620*1 F5-L2025*1/2 F5-L2025*3/4 F5-L2025*1 F5-L2026*1/2 F5-L2026*3/4 F5-L2026*1 F5-L2632*1/2 F5-L2632*3/4 F5-L2632*1 F5-L2632*1 1/4 F5-L2632*1 1/2 F5 Female elbow: F5-L0912*1/2F F5-L0912*3/4F F5-L1216*3/8F F5-L1216*1/4F F5-L1216*1/2F F5-L1216*3/4F F5-L1216*1F F5-L1620*3/8F F5-L1620*1/2F F5-L1620*3/4F F5-L1620*1F F5-L2025*1/2F F5-L2025*3/4F F5-L2025*1F F5-L2026*1/2F F5-L2026*3/4F F5-L2026*1F F5-L2632*1/2F F5-L2632*3/4F F5-L2632*1F F5-L2632*1 1/4F F5-L2632*1 1/2F F5 Equal tee: F5-T0912*0912*0912 F5-T1216*1216*1216 F5-T1620*1620*1620 F5-T2025*2025*2025 F5-T2026*2026*2026 F5-T2632*2632*2632 F5 Unequal tee: F5-T1216*1620*1216 F5-T1620*1216*1216 F5-T1620*1620*1216 F5-T1620*2025*1620 F5-T2025*1216*1216 F5-T2025*1216*1620 F5-T2025*1216*2025 F5-T2025*1620*1216 F5-T2025*1620*1620 F5-T2025*1620*2025 F5-T2025*2025*1216 F5-T2025*2025*1620 F5-T2025*2632*2025 F5-T2632*1216*2632 F5-T2632*1620*2632 F5-T2632*2025*2025 F5-T2632*2025*2632 F5-T0912*1216*0912 F5-T2632*2026*2632 F5-T1620*1216*1620 F5-T1216*2025*1216 F5 Male tee: F5-T0912*1/2*0912 F5-T0912*3/4*0912 F5-T1216*3/8*1216 F5-T1216*1/4*1216 F5-T1216*1/2*1216 F5-T1216*3/4*1216 F5-T1216*1*1216 F5-T1620*3/8*1620 F5-T1620*1/2*1620 F5-T1620*3/4*1620 F5-T1620*1*1620 F5-T2025*1/2*2025 F5-T2025*3/4*2025 F5-T2025*1*2025 F5-T2026*1/2*2026 F5-T2026*3/4*2026 F5-T2026*1*2026 F5-T2632*1/2*2632 F5-T2632*3/4*2632 F5-T2632*1*2632 F5-T2632*1 1/4*2632 F5-T2632*1 1/2*2632 F5 Female tee: F5-T0912*1/2F*0912 F5-T0912*3/4F*0912 F5-T1216*3/8F*1216 F5-T1216*1/4F*1216 F5-T1216*1/2F*1216 F5-T1216*3/4F*1216 F5-T1216*1F*1216 F5-T1620*3/8F*1620 F5-T1620*1/2F*1620 F5-T1620*3/4F*1620 F5-T1620*1F*1620 F5-T2025*1/2F*2025 F5-T2025*3/4F*2025 F5-T2025*1F*2025 F5-T2026*1/2F*2026 F5-T2026*3/4F*2026 F5-T2026*1F*2026 F5-T2632*1/2F*2632 F5-T2632*3/4F*2632 F5-T2632*1F*2632 F5-T2632*1 1/4F*2632 F5-T2632*1 1/2F*2632 F5 Demountable female straight union: F5-S0912*1/2F(H) F5-S0912*3/4F(H) F5-S1216*3/8F(H) F5-S1216*1/4F(H) F5-S1216*1/2F(H) F5-S1216*3/4F(H) F5-S1216*1F(H) F5-S1620*3/8F(H) F5-S1620*1/2F(H) F5-S1620*3/4F(H) F5-S1620*1F(H) F5-S2025*1/2F(H) F5-S2025*3/4F(H) F5-S2025*1F(H) F5-S2026*1/2F(H) F5-S2026*3/4F(H) F5-S2026*1F(H) F5-S2632*1/2F(H) F5-S2632*3/4F(H) F5-S2632*1F(H) F5-S2632*1 1/4F(H) F5-S2632*1 1/2F(H) F5 End cap: F5-D0912 F5-D1216 F5-D1620 F5-D2025 F5-D2026 F5-D2632 F1C End cap: F1-D0912 F1-D1216 F1-D1620 F1-D2025 F1-D2026 F1-D2632 F5 Connector core: F5-C1216x1/2 F5-C1620x1/2 F5-C1216x3/4 F5-C1620x3/4 F5-C2025x3/4 F5 Wall plated female elbow: F5-L1216x1/2F (Z) F5-L1620x1/2F (Z) F5-L1620x3/4F (Z) F5-L1216x1/2F (Z4) F5-L1620x1/2F (Z4) F5-L1620x3/4F (Z4) F1 MLCP to Copper Adaptor: F1-S1216x15Cu C (MUL) F1-S1620x15Cu C (MUL) F1-S1620x22Cu C (MUL) F1-S2025x22Cu C (MUL) F1-S2025x28Cu C (MUL) F1-S2632x28Cu C (MUL) F1-S1216x15Cu2 C F1-S1620x15Cu2 C F1-S2025x28Cu2 C F1-S2632x28Cu2 C F5 MLCP to Copper Adaptor: F5-S1216x15Cu (MUL) F5-S1620x15Cu (MUL) F5-S1620x22Cu (MUL) F5-S2025x22Cu (MUL) F5-S2025x28Cu (MUL) F5-S2632x28Cu (MUL) F5-S1216x15Cu (150) F5-S1620x22Cu (150) F5-S1216x15Cu2 F5-S1620x22Cu2 F5-S2025x22Cu2 F5-S2632x28Cu2 Radiator elbow copper adapter: F5-L1216xφ15S Assembly Double Fittings: F5-L1216xφ15S (Z1) (GZ1) Copper Radiator Tee: F5-T1216xφ15Sx1216

Approval Holder:

Rifeng Enterprise (Foshan) Co., Ltd.

Company Name

Rifeng Enterprise (Foshan) Co., Ltd.

Address

F1-F14 Building No. 1 Rifeng Road Leping Town Sanshui District Foshan City Guangdong Province

Postcode

528318

Country

China

Phone

+86 757 8203 1672

General Email

lio-lu@rifeng.com

View All Listings by this Company

Range of DZR brass compression fittings for use with Q-Therm PEX-b Pipes (SDR 7.4) Maximum working pressure:20 bar, cold water use only

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250902040

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

16mm and 20mm

Marking:

Q-THERM, UAE, DZR and SIZE on compression nut. Pipe: “Q-THERM, 16mm х 2.2mm PE-Xb PN20 DIN 16892/93 ISO 15875 7NO 95° WRAS APPROVED MATERIAL HH: MM DD/MM/YYYY Made in UAE(RAK)

Installation Requirements:

R001 R008

Expiry date:

30/09/2030

Model:

PX00PS2000Y: Q-Therm PEX-b Pipe, DN 16mm, SDR 7.4, PN20, 16mm x 2.2mm PX00PS2001Y: Q-Therm PEX-b Pipe DN 20mm, SDR 7.4, PN20, 20mm x 2.8mm PXYCBE0001R Q-Therm (DZR Brass Concealed Female Elbow with Blue Box) 16mm x ½” BSP (M) (DZR Brass Compression Fitting) PXYCBE0101R Q-Therm (DZR Brass Concealed Female Elbow with Blue Box) 20mm x ½” BSP (M) (DZR Brass Compression Fitting) PXYCRE0001R Q-Therm (DZR Brass Concealed Female Elbow with Red Box) 16mm x ½” BSP (M) (DZR Brass Compression Fitting) PXYCRE0101R Q-Therm (DZR Brass Concealed Female Elbow with Red Box) 20mm x ½” BSP (M (DZR Brass Compression Fitting) PXYCMA0001R Q-Therm DZR Brass Male PE-X Adaptor 16mm x ½” BSP (M) (DZR Brass Compression Fitting) PXYCMA0101R Q-Therm DZR Brass Male PE-X Adaptor 20mm x ½” BSP (M) (DZR Brass Compression Fitting)

Manufacturer:

Quantum Industries LLC

Company Name

Quantum Industries LLC

Address

Al Ghail Industrial Park, Ras Al Khaimah, PB 86488

Country

UAE

View All Listings by this Company

EG Range of copper, brass capillary lead free solder ring fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1115 Fittings for use with Tube and Pipe

Section Subtitle:

Capillary, solder ring, lead free. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250708027

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Eagle brand logo on fitting.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

EG1 Straight Coupling 15mm， 22mm， 28mm， 35mm， 42mm， 54mm EG1M Metric/ Imperial Adaptor 15mm x 1/2"， 22mm x 3/4" EG1R Reducing coupling 22mm x 15mm，28mm x 15mm，28mm x 22mm， 35mm x 22mm，35mm x 28mm，42mm x 28mm， 42mm x 35mm，54mm x 35mm，54mm x 42mm EG1S Slip Coupling 15mm， 22mm， 28mm EG2 Straight Female Connector 15mm x 1/2"，22mm x 1/2"，22mm x 3/4"，28mm x 1"，35mm x 1 1/4"，42mm x 1 1/2"，54mm x 2" EG3 Straight Male Connector 15mm x 1/2"，22mm x 3/4"，28mm x 1"，35mm x 1 1/4"，42mm x 1 1/2"，54mm x 2" EG6 Fitting Reducer 22mm x 15mm，28mm x 15mm，28mm x 22mm， 35mm x 15mm，35mm x 22mm，35mm x 28mm， 42mm x 22mm，42mm x 28mm，42mm x 35mm， 54mm x 28mm，54mm x 35mm，54mm x 42mm EG12 90° Elbow 15mm, 22mm， 28mm， 35mm， 42mm， 54mm EG12S Street Elbow 15mm， 22mm， 28mm EG13 Male Elbow 15mm x 1/2"，22mm x 3/4" EG14 Female Elbow 15mm x 1/2"，22mm x 1/2"，22mm x 3/4" EG15 Wallplate Elbow 15mm x 1/2" EG21 45° Elbow 15mm， 22mm， 28mm， 35mm， 42mm， 54mm EG24 Equal Tee 15mm， 22mm， 28mm， 35mm， 42mm， 54mm EG25 Reduced Branch Tee 22mm x 22mm x 15mm， 28mm x 28mm x 15mm ， 28mm x 28mm x 22mm， 35mm x 35mm x 15mm ， 35mm x 35mm x 22mm， 35mm x 35mm x 28mm ， 42mm x 42mm x 15mm， 42mm x 42mm x 22mm ， 42mm x 42mm x 28mm， 42mm x 42mm x 35mm ， 54mm x 54mm x 15mm， 54mm x 54mm x 22mm ， 54mm x 54mm x 28mm， 54mm x 54mm x 35mm ， 54mm x 54mm x 42mm EG26 Reduced One End Tee 22mm x 15mm x 22mm， 28mm x 15mm x 28mm ， 28mm x 22mm x 28mm EG27 Reduced End & Branch Tee 22mm x 15mm x 15mm， 28mm x 22mm x 15mm ， 28mm x 22mm x 22mm EG28 Two Reduced End Tee 15mm x 15mm x 22mm，22mm x 22mm x 28mm EG30 Centre Female Tee 15mm x 15mm x 1/2"，22mm x 22mm x 1/2"，22mm x 22mm x 3/4" EG61 Stop End 15mm, 22mm， 28mm， 35mm， 42mm， 54mm

Approval Holder:

SCE Technology (Ningbo) Co., Ltd

Company Name

SCE Technology (Ningbo) Co., Ltd

Address

No.32 Yuanqu Road Cha Lu Industrial Zone Ninghai Ningbo Zhejiang

Country

China

View All Listings by this Company

Range of compression fittings with brass, chrome plated brass bodies. For use with copper pipe (EN 1057) Maximum operating pressure 16 bar. Maximum operating temperature 85°C

Section:

1140 Fittings for use with Tube and Pipe

Section Subtitle:

Compression, metal, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250604034

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15MM– 54MM & 1/2” – 1”

Marking:

Lawton & size on compression nut.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

Coupling Compression Chrome COMCP015CP – 15mm COMCP022CP – 22mm COMCP028CP – 28mm COMCP035CP – 35mm COMCP042CP – 42mm COMCP054CP – 54mm Coupling Compression SB-COMCP015 – 15mm SB-COMCP022 – 22mm SB-COMCP028 – 28mm SB-COMCP035 – 35mm SB-COMCP042 – 42mm SB-COMCP054 – 54mm 90 Degree Elbow Compression SB-COMEL015 – 15mm SB-COMEL022 – 22mm SB-COMEL028 – 28mm SB-COMEL035 – 35mm SB-COMEL042 – 42mm SB-COMEL054 – 54mm Equal Tee Compression SB-COMTE015 – 15mm SB-COMTE022 – 22mm SB-COMTE028 – 28mm SB-OMTE035 – 35mm SB-COMTE042 – 42mm SB-COMTE054 – 54mm Male Iron Coupling Compression SB-COMCPMI0153/8 – 15mm x 3/8” SB-COMCPMI0151/2 – 15mm x ½” SB-COMCPMI0221/2 – 22mm x ½” SB-COMCPMI0223/4 – 22mm x ¾” SB-COMCPMI0221 – 22mm x 1 “ SB-COMCPMI0281 – 28mm x 1” Female Iron Coupling Chrome Compression SB-COMCPFI0151/2CP – 15mm x ½” SB-COMCPFI0223/4CP – 22mm x ¾” End Cap Compression SB-COMEC015 – 15mm SB-COMEC022 – 22mm

Approval Holder:

Smith Brothers Stores Limited

Company Name

Smith Brothers Stores Limited

Address

Unit V2 Winchester Avenue, Blaby, Leicester

Postcode

LE8 4GZ

Phone

0116 222 7330

General Email

kel.phillips@sbs.co.uk

View All Listings by this Company

Manufacturer:

The Lawton Tube Company Ltd.

Company Name

The Lawton Tube Company Ltd.

Address

Torrington Avenue, Coventry

Postcode

CV4 9AB

Country

United Kingdom

Phone

+44 24 7646 6203 or 024 7646 6203

General Email

mlis@lawtontubes.co.uk

View All Listings by this Company

Manufacturer:

The Lawton Tube Company Ltd.

Company Name

The Lawton Tube Company Ltd.

Address

Torrington Avenue, Coventry

Postcode

CV4 9AB

Country

United Kingdom

Phone

+44 24 7646 6203 or 024 7646 6203

General Email

mlis@lawtontubes.co.uk

View All Listings by this Company

Range of compression fittings with brass, nickel plated brass bodies for use with copper pipe (manufactured to EN 1057). For above ground use only. Max working pressure 16.0 bar. Max operating temperature 85°C.

Section:

1140 Fittings for use with Tube and Pipe

Section Subtitle:

Compression, metal, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241004055

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

8mm – 54mm. ¼” - 1¼” BSP (M) or (F). Added June 2025: Additional 8 - 35mm sizes (see model). 42mm - 54mm. 1½” - 2” BSP (M) or (F).

Marking:

MT(Brand name) , Size, WRAS and EN 1254-2 on compression nut.

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

Equal Straight: 6601012 - 12×12 6601015 - 15×15 6601018 - 18×18 6601022 - 22×22 6601028 - 28×28 6601035 - 35×35 6601042 - 42x42 6601054 - 54x54 6701008 8×8 6701010 - 10×10 6701012 - 12×12 6701014 - 14×14 6701015 - 15×15 6701016 - 16×16 6701018 - 18×18 6701022 - 22×22 6701028 - 28×28 6701035 - 35×35 6701042 - 42x42 6701054 - 54x54 Reducing Straight: 660101815 - 18×15 660102215 - 22×15 660102218 - 22×18 660102822 - 28×22 670101008 - 10×8 670101210 - 12×10 670101508 - 15×8 670101510- 15×10 670101512 - 15×12 670101815 - 18×15 670102215 - 22×15 670102822 - 28×22 Female Straight 660201215 - 12×1/2" F 660201510 - 15×3/8" F 660201515 - 15×1/2" F 660201520 - 15×3/4" F 660201525 - 15×1" F 660201815 - 18×1/2" F 660201820 - 18×3/4" F 660202215 - 22×1/2" F 660202220 - 22×3/4" F 660202215 - 22×1" F 660202820 - 28×3/4" F 660202825 - 28×1" F 670200810 - 8×3/8" F 670201010 - 10×3/8" F 670201015 - 10×1/2" F 670201210 - 12×3/8" F 670201215 - 12×1/2" F 670201415 - 14×1/2" F 670201510 - 15×3/8" F 670201515 - 15×1/2" F 670201520 - 15×3/4" F 670201525 - 15×1" F 670201615 - 16×1/2"F 670201620 - 16×3/4" F 670201815 - 18×1/2" F 670201820 - 18×3/4" F 670202215 - 22×1/2" F 670202220 - 22×3/4" F 670202225 - 22×1" F 670202820 - 28×3/4" F 670202825 - 28×1" F 670203532 - 35×1 1/4"F 670204240 - 42×1 1/2" F 670205450 - 54×2" F Male Straight: 670301510 - 15×3/8"M 670301515 - 15×1/2"M 670301520- 15×3/4"M 670301815 - 18×1/2"M 670301820 - 18×3/4"M 670302215 - 22×1/2"M 670302220 - 22×3/4"M 670302225- 22×1"M 660302820 - 28×3/4"M 660302825 - 28×1"M 670300806F - 8×1/8"M 670301210F - 12×3/8"M 670301215F - 12×1/2"M 670301410F - 14×3/8"M 670301415F - 14×1/2"M 670301515 - 15×1/2"M 670301520F - 15×3/4"M 670301615F - 16×1/2"M 670301815F - 18×1/2"M 670301820F - 18×3/4"M 670302215 - 22×1/2"M 670302220 - 22×3/4"M 670302820F - 28×3/4"M 670302825 - 28×1"M 670303532F - 35×1 1/4"M 670304240F - 42×1 1/2"M Equal Elbow: 6604015 - 15×15 6604018 - 18×18 6604022 - 22×22 6604028 - 28×28 6604035 - 35×35 6604042 - 42×1 1/2"M 6604054 - 54 x 54 6704008 - 8×8 6704010 - 10×10 6704012 - 12×12 6704014 - 14×14 6704015 - 15×15 6704016 - 16×16 6704018 - 18×18 6704022 - 22×22 6704028 - 28×28 6704035 - 35×35 6704042 - 42x42 6704054 - 54x54 Female Elbow: 670501215 - 12×1/2"F 670501515 - 15×1/2"F 670501520 - 15×3/4"F 670501815 - 18×1/2"F 670501820 - 18×3/4"F 670502215 - 22×1/2"F 670502220 - 22×3/4"F 670582225 - 22×1"F 670502825 - 28×1"F 660501515 - 15×1/2"F 660501520 - 15×3/4"F 660501815 - 18×1/2"F 660501820 - 18×3/4"F 660502215- 22×1/2"F 660502220 - 22×3/4"F 660502225 - 22×1"F 660502825 - 28×1"F Male Elbow: 660601515 - 15×1/2"M 660601520 - 15×3/4"M 660601815 - 18×1/2"M 660601820 - 18×3/4"M 660602215 - 22×1/2"M 660602220 - 22×3/4"M 660602225 - 22×1"M 660602825 - 28×1"M 670601215 - 12×1/2"M 670601415- 14×1/2"M 670601515 - 15×1/2"M 670601520 - 15×3/4"M 670601615 - 16×1/2"M 670601815 - 18×1/2"M 670601820 - 18×3/4"M 670602215 - 22×1/2"M 670602220 - 22×3/4"M 670602225 - 22×1"M 670602825 - 28×1"M Equal Tee: 6608015 - 15×15×15 6608018 - 18×18×18 6608022 - 22×22×22 6608028 - 28×28×28 6608035- 35×35×35 6608042 - 42×42×42 6608054 - 54×54×54 6708010 - 10×10×10 6708012 - 12×12×12 6708014 - 14×14×14 6708015 - 15×15×15 6708016 - 16×16×16 6708018 - 18×18×18 6708022 - 22×22×22 6708028 - 28×28×28 6708035 - 35×35×35 Reducing Tee: 66090152215 - 15×15×22 66090181518 - 18×18×15 66090181815 - 18×15×18 66090221515 - 22×15×15 66090222215- 22×15×22 66090221522 - 22×22×15 66090221822 - 22×22×18 66090282815 - 28×15×28 66090282222 - 28×22×22 66090282822 - 28×22×28 67090152215 -15×15×22 67090181518 - 18×18×15 67090181815 - 18×15×18 67090221515 - 22×15×15 67090222215 - 22×15×22 67090221522 - 22×22×15 67090282815 - 28×15×28 67090282222 - 28×22×22 67090282822 - 28×22×28 Female Tee: 66100151515 - 15×1/2“F 66100181518 - 18×1/2“F 66100182018 - 18×3/4“F 66100221522 - 22×1/2”F 66100222022 - 22×3/4”F 66100282028 - 28×3/4”F 66100282528- 28×1”F 67100151515- 15×1/2“F 67100181518 - 18×1/2“F 67100182018 - 18×3/4“F 67100221522 - 22×1/2”F 67100222022 - 22×3/4”F Wall Plate Elbow: 661101515 - 15×1/2"F 661101815 - 18×1/2"F 661101820 - 18×3/4"F 661102215 - 22×1/2"F 661102220 - 22×3/4"F 671101515 - 15×1/2"F 671102215 - 22×1/2"F 671102220 - 22×3/4"F Stop End: 6607015 - 15 6607018 - 18 6607022 - 22 670708 - 8 6707010 - 10 6707012 - 12 6707015 - 15 6707018 - 18 6707022 - 22 6707028 - 28 Bent Tap Connector: 671301515 - 15×1/2"F 671302220 - 22×3/4"F Crossover Bridge: 6612015 - 15×15 6612018 - 18×18 6612022 - 22×22 6712015 - 15×15 6712022 - 22×22 Where for all models: No suffix = brass body, NP suffix = nickel plated brass,

Approval Holder:

Business Key, S.L.

Company Name

Business Key, S.L.

Address

Poligono Industrial Camps d’En Ricart Carrer Comerç, 10 naves 4-9 08780 Pallejà (Barcelona)

Country

Spain

View All Listings by this Company

‘BF’ range of Brass compression fittings for use with copper pipe manufactured to EN1057 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1150 Fittings for use with Tube and Pipe

Section Subtitle:

Compression, metal, for use with copper tube - above ground use only.

WRAS Approval Number:

250602051

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

South Coast Sales logo on body. EN 1254 and Size on compression Nut.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

BF range comprising of models: BF34821 ¾” Compression x ½” Compression BF34831 1” Compression x 1/2" Compression BF34832 1” Compression x ¾” Compression BF3101 ½” Compression BF3102 ¾” Compression BF3103 1” Compression BF31021 ¾” Compression x ½” Compression BF31032 1” Compression x 1/2" Compression BF31031 1” Compression x ¾” Compression BF3111 ½” BSP (M) x ½” Compression BF31112 ½” BSP (M) x ¾” Compression BF3112 ¾” BSP (M) x ¾” Compression BF31121 ¾” BSP (M) x ½” Compression BF31123 ¾” BSP (M) x 1” Compression BF3113 1” BSP (M) x 1” Compression BF31132 1” BSP (M) x ¾” Compression BF3121 ½” BSP (F) x ½” Compression BF31212 ½” BSP (F) x ¾” Compression BF3122 ¾” BSP (F) x ¾” Compression BF31221 ¾” BSP (F) x ½” Compression BF31223 ¾” BSP (F) x 1” Compression BF3123 1” BSP (F) x 1” Compression BF31232 1” BSP (F) x ¾” Compression BF3141 ½” Compression x 1/2"swivel F BF3271 ½” Compression x 1/2"swivel F BF3151 ½” Compression BF3152 ¾” Compression BF3153 1” Compression BF31521 ¾” Compression x 1/2" Compression BF31532 1" Compression x ¾” Compression BF3161 ½” BSP (M) x ½” Compression BF31612 ½” BSP (M) x ¾” Compression BF3162 ¾” BSP (M) x ¾” Compression BF31621 ¾” BSP (M) x ½” Compression BF31623 ¾” BSP (M) x 1” Compression BF3163 1” BSP (M) x 1” Compression BF31632 1” BSP (M) x ¾” Compression BF3171 ½” BSP (M) x ½” Compression BF31712 ½” BSP (M) x ¾” Compression BF3172 ¾” BSP (M) x ¾” Compression BF31721 ¾” BSP (M) x ½” Compression BF31723 ¾” BSP (M) x 1” Compression BF3173 1” BSP (M) x 1” Compression BF31732 1” BSP (M) x ¾” Compression BF3181 1/2" Compression BF3182 ¾” Compression BF3183 1" Compression BF320222 ¾” BSP (M) x ¾” Compression x ¾” Compression BF320333 1” BSP (M) x 1” Compression x 1” Compression BF318112 1/2" Compression x 1/2" Compression x ¾” Compression BF318211 ¾” Compression x 1/2" Compression x 1/2" Compression BF318212 ¾” Compression x 1/2" Compression x ¾” Compression BF318221 ¾” Compression x ¾” Compression x 1/2" Compression BF318223 ¾” Compression x ¾” Compression x 1" Compression BF318311 1" Compression x 1/2" Compression x 1/2" Compression BF318313 1" Compression x ½” Compression x 1" Compression BF318322 1" Compression x ¾” Compression x ¾” Compression BF318323 1" Compression x ¾” Compression x 1" Compression BF318331 1" Compression x 1" Compression x 1/2" Compression BF318332 1" Compression x 1" Compression x ¾” Compression BF3301 ½” Compression x ½” Compression x ½” BSP (F) BF3302 ¾” Compression x ¾” Compression x ¾” BSP (F) BF330221 ¾” Compression x ¾” Compression x ½” BSP (F) BF3303 1” Compression x 1” Compression x 1” BSP (F) BF330331 1” Compression x 1” Compression x ½” BSP (F) BF330332 1” Compression x 1” Compression x ¾” BSP (F) BF3402 ¾” BSP (M) x F COMPRESSION BF3403 1” BSP (M) x F COMPRESSION BF3211 ½” Compression x ½” BSP (F) BF3212 ¾” Compression x ¾” BSP (F) BF 32112 ¾” Compression x ½” BSP (F) BF3501 ½” Compression BF3502 ¾” Compression BF3503 1” Compression BF3511 ½” Compression BF3512 ¾” Compression BF3513 1" Compression

Approval Holder:

South Coast Sales

Company Name

South Coast Sales

Address

1 Doughcloyne Industrial Estate, Sarsfield Road, Wilton, Cork.

Postcode

T12 TR62

Country

Ireland

Phone

00353 21 - 43 46 143

General Email

info@southcoastsales.com

View All Listings by this Company

Range of compression fittings with polypropylene bodies for use with PE100 pipe (manufactured to EN 12201). Some of the female adaptors (55920-9-L, 55920-10-L, 55920-11-L & 55920-11-M), female threaded elbows (56935-10-L, 56935-11-L & 56935-11-M) have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 16.0 bar. For above and below ground, cold water use.

Section:

1160 Fittings for use with Tube and Pipe

Section Subtitle:

Compression, plastic, for use with plastic tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250902025

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

20mm – 110mm. (please note: 20mm-50mm sizes added January 2026).

Marking:

Plastica Alpha logo, size and date of manufacture (MM/YY) on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

Blu Line Plus: 53910-8 Coupling ø63 mm 53910-9 Coupling ø75 mm 53910-10 Coupling ø90 mm 53910-11 Coupling ø110 mm 53915-8 Repair Coupling ø63 mm 53915-9 Repair Coupling ø75 mm 53915-10 Repair Coupling ø90 mm 53915-11 Repair Coupling ø110 mm 53920-8-3 Reducing coupling ø63 - 25 53920-8-4 Reducing coupling ø63 - 32 53920-8-6 Reducing coupling ø63 - 40 53920-8-7 Reducing coupling ø63 - 50 53920-9-6 Reducing coupling ø75 - 40 53920-9-7 Reducing coupling ø75 - 50 53920-9-8 Reducing coupling ø75 - 63 53920-10-8 Reducing coupling ø90 - 63 53920-10-9 Reducing coupling ø90 - 75 53920-11-8 Reducing coupling ø110 - 63 53920-11-9 Reducing coupling ø110 - 75 53920-11-10 Reducing coupling ø110 - 90 55910-8-F Male adaptor ø63 x 1”½ 55910-8-G Male adaptor ø63 x 2” 55910-8-H Male adaptor ø63 x 2”½ 55910-9-G Male adaptor ø75 x 2” 55910-9-H Male adaptor ø75 x 2”½ 55910-9-L Male adaptor ø75 x 3” 55910-10-G Male adaptor ø90 x 2” 55910-10-H Male adaptor ø90 x 2”½ 55910-10-L Male adaptor ø90 x 3” 55910-10-M Male adaptor ø90 x 4” 55910-11-L Male adaptor ø110 x 3” 55910-11-M Male adaptor ø110 x 4” 55920-8-F Female adaptor ø63 x 1” ½ 55920-8-G Female adaptor ø63 x 2” 55920-9-G Female adaptor ø75 x 2” 55920-9-H Female adaptor ø75 x 2” ½ 55920-9-L Female adaptor ø75 x 3” 55920-10-L Female adaptor ø90 x 3” 55920-11-L Female adaptor ø110 x 3” 55920-11-M Female adaptor ø110 x 4” 56950-8 90° elbow ø63 mm 56950-9 90° elbow ø75 mm 56950-10 90° elbow ø90 mm 56950-11 90° elbow ø110 mm 56925-8-F 90° male threaded elbow ø63 x 1” ½ 56925-8-G 90° male threaded elbow ø63 x 2” 56925-8-H 90° male threaded elbow ø63 x 2” ½ 56925-9-G 90° male threaded elbow ø75 x 2” 56925-9-H 90° male threaded elbow ø75 x 2” ½ 56925-10-L 0° male threaded elbow ø90 x 3” 56925-10-M 90° male threaded elbow ø90 x 4” 56925-11-M 90° male threaded elbow ø110 x 4” 56935-8-G 90° female threaded elbow ø63 x 2” 56935-9-G 90° female threaded elbow ø75 x 2” 56935-9-H 90° female threaded elbow ø75 x 2” ½ 56935-10-H 90° female threaded elbow ø90 x 2” ½ 56935-10-L 90° female threaded elbow ø90 x 3” 56935-11-L 90° female threaded elbow ø110 x 3” 56935-11-M 90° female threaded elbow ø110 x 4” 54910-8 90° tee ø63 mm 54910-9 90° tee ø75 mm 54910-10 90° tee ø90 mm 54910-11 90° tee ø110 mm 54920-9-8 90° reducing tee ø54920-9-8 54920-10-9 90° reducing tee ø54920-10-9 54920-11-8 90° reducing tee ø54920-11-8 54920-11-9 90° reducing tee ø54920-11-9 54920-11-10 90° reducing tee ø54920-11-10 54930-8-G 90° male threaded tee ø63 x 2” 54930-8-H 90° male threaded tee ø63 x 2”½ 54930-9-G 90° male threaded tee ø75 x 2” 54930-10-L 90° male threaded tee ø90 x 3” 54930-10-M 90° male threaded tee ø90 x 4” 54930-11-L 90° male threaded tee ø110 x 3” 54930-11-M 90° male threaded tee ø110 x 4” 54940-7-G 90° female threaded tee ø63 x 2” 54940-8-G 90° female threaded tee ø63 x 2”½ 54940-9-G 90° female threaded tee ø75 x 2” 54940-10-L 90° female threaded tee ø90 x 3” 54940-10-M 90° female threaded tee ø90 x 4” 54940-11-L 90° female threaded tee ø110 x 3” 54940-11-M 90° female threaded tee ø110 x 4” 56941-8 End cap ø63 mm 56941-9 End cap ø75 mm 56941-10 End cap ø90 mm 56941-11 End cap ø110 mm 55930-8-G Flanged adaptor ø63 x 2” 55930-9-H Flanged adaptor ø75 x 2”½ 55930-9-L Flanged adaptor ø75 x 3” 55930-10-L Flanged adaptor ø90 x 3” 55930-10-M Flanged adaptor ø90 x 4” 55930-11-M Flanged adaptor ø110 x 4” 56980-8-G 90° Flanged Elbow ø63 x 2” 56980-9-H 90° Flanged Elbow ø75 x 2”½ 56980-9-L 90° Flanged Elbow ø75 x 3” 56980-10-L 90° Flanged Elbow ø90 x 3” 56980-10-M 90° Flanged Elbow ø90 x 4” 56980-11-M 90° Flanged Elbow ø110 x 4” 54930-8-G 90° Flanged Tee ø63 x 2” 54930-9-H 90° Flanged Tee ø75 x 2”½ 54930-9-L 90° Flanged Tee ø75 x 3” 54930-10-L 90° Flanged Tee ø90 x 3” 54930-10-M 90° Flanged Tee ø90 x 4” 54930-11-M 90° Flanged Tee ø110 x 4” Models added January 2026: 53910-2 Coupling ø20 mm 53910-3 Coupling ø25 mm 53910-4 Coupling ø32 mm 53910-6 Coupling ø40 mm 53910-7 Coupling ø50 mm 53915-2 Repair Coupling ø20 mm 53915-3 Repair Coupling ø25 mm 53915-4 Repair Coupling ø32 mm 53915-6 Repair Coupling ø40 mm 53915-7 Repair Coupling ø50 mm 53920-3-2 Reducing coupling ø25 - 20 53920-4-2 Reducing coupling ø32 - 20 53920-4-3 Reducing coupling ø32 - 25 53920-6-4 Reducing coupling ø40 - 32 53920-7-4 Reducing coupling ø50 - 32 53920-7-6 Reducing coupling ø50 - 40 55910-2-B Male adaptor ø20 x ½” 55910-2-C Male adaptor ø20 x ¾” 55910-3-B Male adaptor ø25 x ½” 55910-3-C Male adaptor ø25 x ¾” 55910-3-D Male adaptor ø25 x 1” 55910-4-B Male adaptor ø32 x ½” 55910-4-C Male adaptor ø32 x ¾” 55910-4-D Male adaptor ø32 x 1” 55910-4-E Male adaptor ø32 x 1”¼ 55910-6-D Male adaptor ø40 x 1” 55910-6-E Male adaptor ø40 x 1”¼ 55910-6-F Male adaptor ø40 x 1”½ 55910-7-F Male adaptor ø50 x 1”½ 55910-7-G Male adaptor ø50 x 2” 55920-2-B Female adaptor ø20 x ½” 55920-2-C Female adaptor ø20 x ¾” 55920-3-B Female adaptor ø25 x ½” 55920-3-C Female adaptor ø25 x ¾” 55920-3-D Female adaptor ø25 x 1” 55920-4-C Female adaptor ø32 x ¾” 55920-4-D Female adaptor ø32 x 1” 55920-6-D Female adaptor ø40 x 1” 55920-6-E Female adaptor ø40 x 1” ¼ 55920-6-F Female adaptor ø40 x 1” ½ 55920-7-F Female adaptor ø50 x 1” ½ 55920-7-G Female adaptor ø50 x 2” 56950-2 90° elbow ø20 mm 56950-3 90° elbow ø25 mm 56950-4 90° elbow ø32 mm 56950-6 90° elbow ø40 mm 56950-7 90° elbow ø50 mm 56925-2-B 90° male threaded elbow ø20 x ½” 56925-2-C 90° male threaded elbow ø20 x ¾” 56925-3-B 90° male threaded elbow ø25 x ½” 56925-3-C 90° male threaded elbow ø25 x ¾” 56925-3-D 90° male threaded elbow ø25 x 1” 56925-4-C 90° male threaded elbow ø32 x ¾” 56925-4-D 90° male threaded elbow ø32 x 1” 56925-4-E 90° male threaded elbow ø32 x 1” ¼ 56925-6-D 90° male threaded elbow ø40 x 1” 56925-6-E 90° male threaded elbow ø40 x 1” ¼ 56925-6-F 90° male threaded elbow ø40 x 1” ½ 56925-6-G 90° male threaded elbow ø40 x 2” 56925-7-E 90° male threaded elbow ø50 x 1” ¼ 56925-7-F 90° male threaded elbow ø50 x 1” ½ 56925-7-G 90° male threaded elbow ø50 x 2” 56935-2-B 90° female threaded elbow ø20 x ½” 56935-2-C 90° female threaded elbow ø20 x ¾” 56935-3-B 90° female threaded elbow ø25 x ½” 56935-3-C 90° female threaded elbow ø25 x ¾” 56935-3-D 90° female threaded elbow ø25 x 1” 56935-4-C 90° female threaded elbow ø32 x ¾” 56935-4-D 90° female threaded elbow ø32 x 1” 56935-6-D 90° female threaded elbow ø40 x 1” 56935-6-E 90° female threaded elbow ø40 x 1” ¼ 56935-7-F 90° female threaded elbow ø50 x 1” ½ 56935-7-G 90° female threaded elbow ø50 x 2” 56965-2-B 90° wall plate elbow ø20 x ½” 56965-3-B 90° wall plate elbow ø25 x ½” 56965-3-C 90° wall plate elbow ø25 x ¾” 56965-4-D 90° wall plate elbow ø32 x 1” 54910-2 90° tee ø20 mm 54910-3 90° tee ø25 mm 54910-4 90° tee ø32 mm 54910-6 90° tee ø40 mm 54910-7 90° tee ø50 mm 54920-2-3 90° reducing tee ø54920-2-3 54920-3-2 90° reducing tee ø54920-3-2 54920-4-2 90° reducing tee ø54920-4-2 54920-4-3 90° reducing tee ø54920-4-3 54920-6-3 90° reducing tee ø54920-6-3 54920-6-4 90° reducing tee ø54920-6-4 54920-7-3 90° reducing tee ø54920-7-3 54920-7-4 90° reducing tee ø54920-7-4 54920-7-6 90° reducing tee ø54920-7-6 54920-8-3 90° reducing tee ø54920-8-3 54920-8-4 90° reducing tee ø54920-8-4 54920-8-6 90° reducing tee ø54920-8-6 54920-8-7 90° reducing tee ø54920-8-7 54930-1-C 90° male threaded tee ø16 x ¾” 54930-2-B 90° male threaded tee ø20 x ½” 54930-2-C 90° male threaded tee ø20 x ¾” 54930-3-B 90° male threaded tee ø25 x ½” 54930-3-C 90° male threaded tee ø25 x ¾” 54930-3-D 90° male threaded tee ø25 x 1” 54930-4-C 90° male threaded tee ø32 x ¾” 54930-4-D 90° male threaded tee ø32 x 1” 54930-6-D 90° male threaded tee ø40 x 1” 54930-6-E 90° male threaded tee ø40 x 1”¼ 54930-6-F 90° male threaded tee ø40 x 1”½ 54930-7-F 90° male threaded tee ø50 x 1”½ 54930-7-G 90° male threaded tee ø50 x 2” 54940-2-B 90° female threaded tee ø20 x ½” 54940-2-C 90° female threaded tee ø20 x ¾” 54940-3-B 90° female threaded tee ø25 x ½” 54940-3-C 90° female threaded tee ø25 x ¾” 54940-3-D 90° female threaded tee ø25 x 1” 54940-4-C 90° female threaded tee ø32 x ¾” 54940-4-D 90° female threaded tee ø32 x 1” 54940-6-D 90° female threaded tee ø40 x 1” 54940-6-E 90° female threaded tee ø40 x 1”¼ 54940-6-F 90° female threaded tee ø40 x 1”½ 54940-7-E 90° female threaded tee ø50 x 1”½ 54940-7-F 90° female threaded tee ø50 x 2” 56941-2 End cap ø20 mm 56941-3 End cap ø25 mm 56941-4 End cap ø32 mm 56941-6 End cap ø40 mm 56941-7 End cap ø50 mm 55930-7-G Flanged adaptor ø50 x 2” 56980-7-F 90° Flanged Elbow ø50 x1”½ 56980-7-G 90° Flanged Elbow ø50 x 2” 54980-7-F 90° Flanged Tee ø50 x1”½ 54930-7-G 90° Flanged Tee ø50 x 2”

Manufacturer:

Plastica Alfa S.p.a.

Company Name

Plastica Alfa S.p.a.

Address

C.da S.M. Poggiarelli, Z.I., 95041 Caltagirone (CT), Italy

View All Listings by this Company

"PRESSTITE" range of press fittings with nickel plated brass bodies incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved by a TH crimping profile. For above ground use only. Maximum working pressure 10.0 bar. 20 & 26mm pressfit sizes cold water use only. Threaded and pressfit 16mm size maximum operating temperature 95°C. From June 2025: The 20 & 26mm pressfit sizes maximum operating temperature 95°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

240404724

Size:

Pressfit: 16, 20 & 26mm. Threaded: ½”, ¾” & 1” BSP (M)/(F) or captive nut.

Marking:

IDC logo: E mark (~E~ within circle), profile type (TH), size and PN on fitting body.

Installation Requirements:

R001

Expiry date:

30/04/2029

Model:

Straight PEX x PEX (press x press): 900310002 - 16mm x 16mm 900310003 - 20mm x 20mm 900310004 - 26mm x 26mm Reduce Straight PEX x PEX (press x press): 900310032 - 20mm x 16mm 900310042 - 26mm x 16mm 900310043 - 26mm x 20mm Straight PEX x Female (press x female): 900312003 - 20mm x 1/2"F 900312004 - 26mm x 3/4"F 900312023 - 16mm x 1/2"F 900312034 - 20mm x 3/4"F 900312045 - 26mm x 1"F Stop end (press): 900372002 - 16mm 900372003 - 20mm 900372004 - 26mm Elbow (press): 900315002 - 16mm 900315003 - 20mm 900315004 - 26mm Elbow PEX x Male (press x male): 900316023 - 16mm x 1/2"M 900316003 - 20mm x 1/2"M 900316034 - 20mm x 3/4"M 900316004 - 26mm x 3/4"M Elbow PEX x Female (press x female): 900317023 - 16mm x 1/2"F 900317003 - 20mm x 1/2"F 900317034 - 20mm x 3/4"F 900317004 - 26mm x 3/4"F Wall Plate PEX x Female (press x female): 900307023 - 16 x 1/2"F 900307003 - 20 x 1/2"F 900307034 - 20 x 3/4"F 900307004 - 26 x 3/4"F Equal Tee (press): 900318002 - 16mm 900318003 - 20mm 900318004 - 26mm Reduce Tee PEX(Left) x PEX(Right) x PEX(Middle) (press x press x press): 900318232 - 16 x 20 x 16 900318322 - 20 x 16 x 16 900318323 - 20 x 16 x 20 900318332 - 20 x 20 x 16 900318343 - 20 x 26 x 20 900318422 - 26 x 16 x 16 900318423 - 26 x 16 x 20 900318424 - 26 x 16 x 26 900318432 - 26 x 20 x 16 900318433 - 26 x 20 x 20 900318434 - 26 x 20 x 26 900318442 - 26 x 26 x 16 900318443 - 26 x 26 x 20 900318454 - 26 x 32 x 26 Reduce Tee PEX(Left) x PEX(Right) x Female(Middle) (press x female x press): 900330004 - 26 x 3/4"F x 20 900330023 - 16 x 1/2"F x 16 900330033 - 20 x 1/2"F x 20 900330034 - 20 x 3/4"F x 20 900330043 - 26 x 1/2"F x 26

Approval Holder:

Hevac Ltd

Company Name

Hevac Ltd

Address

Muirfield Drive Naas Road Dublin 12

Postcode

D12 X0A3

Country

Ireland

Phone

0035 314 191924

General Email

dave.grenville@hevac.ie

View All Listings by this Company

Manufacturer:

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Company Name

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Address

3rd Floor, Unit 2, Building 2, Section A Zhaowei Science & Technology Park No. 14, Jiuxianqiao Road Chaoyang District Beijing

Postcode

100015

Country

China

Phone

008610 51659550 ext 312

General Email

Jerry.tang@idcgroup.com.cn

View All Listings by this Company

Manufacturer:

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Company Name

IDC Plumbing & Heating Technology (Beijing) Co., Ltd.

Address

3rd Floor, Unit 2, Building 2, Section A Zhaowei Science & Technology Park No. 14, Jiuxianqiao Road Chaoyang District Beijing

Postcode

100015

Country

China

Phone

008610 51659550 ext 312

General Email

Jerry.tang@idcgroup.com.cn

View All Listings by this Company

Range of stainless-steel press fittings (SUS304 or 316L) with EPDM ‘O’-rings for use with stainless-steel pipe (SUS304 or 316L EN 10312), using an ‘M’ press profile. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241004054

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SEE MODEL

Marking:

KPress logo, material and size on body.

Installation Requirements:

R001

Expiry date:

31/10/2029

Model:

HB-H15XXX - 45 Degree Equal Elbow - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I15XXX - 45 Degree Equal Elbow - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H16XXX - 45 Degree Plain End Elbow - SUS304 - 28, 35, 42, 54. HB-I16XXX - 45 Degree Plain End Elbow - SUS316L - 28, 35, 42, 54. HB-H07XXX - 90 Degree Equal Elbow - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I07XXX - 90 Degree Equal Elbow - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H08XXX - 90 Degree Female Thread Elbow - SUS304 - 18xRp1/2", 22xRp1/2", 28xRp1", 35xRp1", 35x Rp1 1/4", 42xRp1 1/2", 42xRp1 1/4", 54xRp2", 76.1xRp2 1/2". HB-I08XXX - 90 Degree Female Thread Elbow - SUS316L - 18xRp1/2", 22xRp1/2", 28xRp1", 35xRp1", 35x Rp1 1/4", 42xRp1 1/2", 42xRp1 1/4", 54xRp2", 76.1xRp2 1/2". HB-H09XXX - 90 Degree Male Thread Elbow - SUS304 - 18xR1/2", 35xR1", 35x R1 1/4", 42xR1 1/2", 42xR1 1/4", 54xR2", 76.1xR2 1/2", 88.9xR3", 108xR4". HB-I09XXX - 90 Degree Male Thread Elbow - SUS316L - 18xR1/2", 35xR1", 35x R1 1/4", 42xR1 1/2", 42xR1 1/4", 54xR2", 76.1xR2 1/2", 88.9xR3", 108xR4". HB-H14XXX - 90 Degree Plain End Elbow - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I14XXX - 90 Degree Plain End Elbow - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H18XXX - Cap - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I18XXX - Cap - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H01XXX - Coupling - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I01XXX - Coupling - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H03XXX - Male Thread Adapter - SUS304 - 18xR1/2", 22xR1/2", 28xR1", 35xR1", 35x R1 1/4", 42xR1 1/2", 42xR1 1/4", 54xR2", 76.1xR2 1/2". HB-I03XXX - Male Thread Adapter - SUS316L - 18xR1/2", 22xR1/2", 28xR1", 35xR1", 35x R1 1/4", 42xR1 1/2", 42xR1 1/4", 54xR2", 76.1xR2 1/2". HB-H24XXX - Plain End Coupling - SUS304 - 28x35, 28x42, 35x42, 42x54, 54x76.1, 35x28, DN40x25, DN40x32, DN65x40, DN65x32. HB-I24XXX - Plain end Coupling - SUS316L - 28x35, 28x42, 35x42, 42x54, 54x76.1, 35x28, DN40x25, DN40x32, DN65x40, DN65x32. HB-H02XXX - Reducing Coupling - SUS304 - 22x18, 28x18, 28x22, 35x18, 35x22, 35x28, 42x18, 42x22, 42x28. HB-I02XXX - Reducing Coupling - SUS316L - 22x18, 28x18, 28x22, 35x18, 35x22, 35x28, 42x18, 42x22, 42x28. HB-H13XXX - Reducing Cross - SUS304 - 35x28, 42x28, 54x28, 76.1x28, 88.9x28, 54x35, 76.1x35, 88.9x35, 108x35, DN80x40, DN80x50, DN100x40. HB-I13XXX - Reducing Cross - SUS316L - 35x28, 42x28, 54x28, 76.1x28, 88.9x28, 54x35, 76.1x35, 88.9x35, 108x35, DN80x40, DN80x50, DN100x40. HB-H06XXX - Reducing Tee - SUS304 - 22x18, 28x18, 28x22, 35x18, 35x22, 35x28, 42x18, 42x22, 42x28. HB-I06XXX - Reducing Tee - SUS316L - 22x18, 28x18, 28x22, 35x18, 35x22, 35x28, 42x18, 42x22, 42x28. HB-H19XXX - Slip Coupling - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I19XXX - Slip Coupling - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H11XXX - Tee with male Thread - SUS304 - 18xR1/2", 22xR1/2", 22xR3/4", 28xR1/2", 28xR3/4", 28xR1", 35xR1/2", 35xR3/4", 35xR1". HB-I11XXX - Tee with male Thread - SUS316L - 18xR1/2", 22xR1/2", 22xR3/4", 28xR1/2", 28xR3/4", 28xR1", 35xR1/2", 35xR3/4", 35xR1". HB-H20XXX - Union Adapter - SUS304 - 18xG1/2", 18xG3/4", 22xG1/2", 22xG3/4", 22xG1", 28xG1", 35xG1 1/4", 42xG 1 1/2". HB-I20XXX - Union Adapter - SUS316L - 18xG1/2", 18xG3/4", 22xG1/2", 22xG3/4", 22xG1", 28xG1", 35xG1 1/4", 42xG 1 1/2". HB-H05XXX - Equal Tee - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I05XXX - Equal Tee - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H12XXX - Equal Cross - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I12XXX - Equal Cross - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-H10XXX - Tee with Female Thread - SUS304 - 18xRp1/2", 22xRp1/2", 22xRp3/4", 28xRp1/2", 28x Rp3/4", 28xRp1", 35xRp1/2", 35xRp3/4", 35xRp1". HB-I10XXX - Tee with Female Thread - SUS316L - 18xRp1/2", 22xRp1/2", 22xRp3/4", 28xRp1/2", 28x Rp3/4", 28xRp1", 35xRp1/2", 35xRp3/4", 35xRp1". HB-H00XXX - Stainless Steel Pipe - SUS304 - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. HB-I00XXX - Stainless Steel Pipe - SUS316L - 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108.

Approval Holder:

Kesanitar GmbH

Company Name

Kesanitar GmbH

Address

Märkische Straße 12, 47809 Krefeld, NRW

Country

Germany

Phone

+49 2151 3624071

General Email

info@kesanitar.com

View All Listings by this Company

5000 series of copper end feed fittings for use with EN 1057 copper tube. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250708026

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Eagle brand logo on fitting.

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

5001A 90° Street bend 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5002G 90° Bent tap Connector 15mm x ½”, 15mm x ¾”, 22mm x ¾” 5002A 90° Bend 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5040 45° Street Elbow 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5041 45° Elbow 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5085 Full Crossover 15mm, 22mm 5086 Partial Crossover 15mm, 22mm 5090 90° Elbow 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5090R 90° Elbow 22mm x 15mm 5092 90° Street Elbow 10mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm 5130 Equal Tee 8mm, 10mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm 5301 End Cap 15mm， 22mm， 28mm， 35mm， 42mm， 54mm 5130R Reducing Tee 15mmx22mmx15mm，22mmx15mmx15mm， 22mmx15mmx22mm，22mmx22mmx15mm， 22mmx28mmx22mm，28mmx15mmx15mm， 28mmx15mmx28mm，28mmx22mmx22mm， 28mmx22mmx28mm，28mmx28mmx15mm， 28mmx28mmx22mm，35mmx15mmx35mm， 35mmx22mmx35mm，35mmx28mmx28mm， 35mmx28mmx35mm，42mmx15mmx42mm， 42mmx22mmx42mm，42mmx28mmx42mm， 42mmx35mmx42mm，54mmx15mmx54mm， 54mmx22mmx54mm，54mmx28mmx54mm， 54mmx35mmx54mm，54mmx42mmx54mm 5240 Reducing Coupling 22mm x 15mm，28mm x 15mm，28mm x 22mm， 35mm x 15mm，35mm x 22mm，35mm x 28mm， 42mm x 15mm，42mm x 22mm，42mm x 28mm， 42mm x 35mm，54mm x 22mm，54mm x 28mm 54mm x 35mm, 54mm x 42mm 5421 Metric imperial Coupling 15mm x ½”, 22mm x ¾” 5270 Straight Coupling 15mm， 22mm， 28mm, 35mm, 42mm, 54mm 5243 Fitting reducer 22mm x 15mm，28mm x 15mm，28mm x 22mm， 35mm x 15mm，35mm x 22mm，35mm x 28mm， 42mm x 15mm，42mm x 22mm，42mm x 28mm， 42mm x 35mm，54mm x 22mm，54mm x 28mm 54mm x 35mm, 54mm x 42mm 5359G Straight Tap Connector 15mm x 1/2"，15mm x 3/4"，22mm x 3/4"

Approval Holder:

SCE Technology (Ningbo) Co., Ltd

Company Name

SCE Technology (Ningbo) Co., Ltd

Address

No.32 Yuanqu Road Cha Lu Industrial Zone Ninghai Ningbo Zhejiang

Country

China

View All Listings by this Company

Dual flush, WC outlet valves for either full or reduced flush. Incorporates an internal overflow. Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

250902702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

2” BSP (M)

Marking:

R&T logo & model body.

Installation Requirements:

R001 R556 R571

Expiry date:

30/09/2030

Model:

A2415L, A2415M & A2706

Manufacturer:

Xiamen R&T Plumbing Technology Co.,Ltd

Company Name

Xiamen R&T Plumbing Technology Co.,Ltd

Address

No.18, Houxiang Road Haicang District Xiamen

Postcode

361022

Country

China

Phone

86-0592-3959422

View All Listings by this Company

Dual flush, WC outlet valve operated via a lever operated assembly for either full or reduced flush. Incorporates an internal overflow. Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

250902701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

2” BSP (M)

Marking:

R&T logo & model on body.

Installation Requirements:

R001 R556 R571

Expiry date:

30/09/2030

Model:

A24233

Manufacturer:

Xiamen R&T Plumbing Technology Co.,Ltd

Company Name

Xiamen R&T Plumbing Technology Co.,Ltd

Address

No.18, Houxiang Road Haicang District Xiamen

Postcode

361022

Country

China

Phone

86-0592-3959422

View All Listings by this Company

Range of dual flush WC outlet valves operated via a push button assembly for either full or reduced flush and incorporates an internal overflow. Cold water use only.

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

250902710

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

2” BSP (M)

Marking:

WDI, model & WRAS on body.

Installation Requirements:

R001 R556 R571

Expiry date:

30/09/2030

Model:

B4900-U B4900-G B4900H-U B4900H-G

Stainless steel plate heat exchangers with copper brazing.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

0.75 to 2”.

Marking:

UK Exchangers and product info on label.

Installation Requirements:

R001

Expiry date:

30/11/2030

Model:

UKE-BR030 UKE-BR040 UKE-BR060H UKE-BR050 UKE-BR050R UKE-BR095H BR200L UKE-BR200M UKE-BR205 UKE-BRX12B

Approval Holder:

UK Exchangers Ltd

Company Name

UK Exchangers Ltd

Address

Unit 55 Stilebrook Road Olney

Postcode

MK46 5EA

Country

United Kingdom

General Email

alex@ukeltd.com

View All Listings by this Company

Near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241202719

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8” BSP M inlet/outlet

Marking:

Alfred Victoria "crown" logo on front of body. Model and product info on label on rear of body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

F104M

Approval Holder:

ALFRED VICTORIA LIMITED

Company Name

ALFRED VICTORIA LIMITED

Postcode

B45 9AL

Country

United Kingdom

Phone

00441213592214

General Email

daisy.qin@alfredvictoria.co.uk

View All Listings by this Company

Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) or 1” BSP (M)

Marking:

APATOR, date of manufacture (YYYY) and product information on face of water meter. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

Maximum operating temperature 50°C: JS 1,6-02 JS 1,6-04 JS 1,6-NK JS 1,6-NKP JS 4-02 JS 4-04 JS 4-NK JS 4-NKP JS 2,5-02 JS 2,5-04 JS 2,5-NK JS 2,5-NKP JS 2,5-G1-02 JS 2,5-G1-04 JS 2,5-G1-NK JS 2,5-G1-NKP Maximum operating temperature 85°C: JS90 1,6-02 JS90 1,6-04 JS90 1,6-NK JS901,6-NKP JS90 2,5-02 JS90 2,5-04 JS90 2,5-NK JS90 2,5-NKP JS90 2,5-G1-02 JS90 2,5-G1-04 JS90 2,5-G1-NK JS90 2,5-G1-NKP JS90 4-02 JS90 4-04 JS90 4-NK JS90 4-NKP

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Manufacturer:

Apator Powogaz S.A.

Company Name

Apator Powogaz S.A.

Address

Jaryszki 1C, 62-023 Żerniki

Country

Poland

Phone

+48 789 454 593

View All Listings by this Company

Compact wall outlet elbow with brass body (various finishes). Maximum operating temperature 85.0°C Open outlet use only

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M)

Marking:

Aqualisa on body

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Model:

1001359 ** ** Where ** ** denotes the finish and can be replaced with the following: AA = Chrome AD = Matt Black AH = Core Brushed Brass Post 24 (Xenia) AJ = Core Brushed Gunmetal Grey AQ = Aqualisa (Brand)

Approval Holder:

Aqualisa Products Ltd.

Company Name

Aqualisa Products Ltd.

Address

Unit 6 The Flyers Way, Westerham, Kent

Postcode

TN6 1DE

Phone

07920 790367

General Email

tracey.jones@aqualisa.co.uk

View All Listings by this Company

Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Sika logo, pressure, temperature, other tech info on body; flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

VVXA Vortex Flow Sensor Type VVX15 Vortex Flow Sensor nominal size 15. Body material PPS, G ¾ male or ½” NPT male VVXC Vortex Flow Sensor Type VVX20 Vortex Flow Sensor nominal size 20. Body material PPS G 1 male or ¾” NPT male or Quick-Fasten male/female VVXB Vortex Flow Sensor Type VVX25 Vortex Flow Sensor nominal size 25. Body material PPS G 1¼ male or 1” NPT male VVXD Vortex Flow Sensor Type VVX32 Vortex Flow Sensor nominal size 32. Body material brass or stainless steel G 1½ male or 1½” NPT male VVXE Vortex Flow Sensor Type VVX40 Vortex Flow Sensor nominal size 40. Body material brass or stainless steel G 2 male or 2” NPT male • digit 1,2,3: Designation of the series o VVX >>> VVX series • digit 4: nominal diameter o A >>> DN 15 for type VVX15 o C >>> DN 20 for type VVX20 o B >>> DN 25 for type VVX25 o D >>> DN 32 for type VVX32 o E >>> DN 40 for type VVX40 • digit 5,7,8,9,10,11,12,13,14,15: Device configuration • digit 6: Private label o S >>> SIKA (standard) o E >>> SIKA (standard) with ETL marking • digit 4 and 16: tube material / process connection o A and 4 >>> PPS – G 3/4 male thread o A and C >>> PPS – ½”NPT male thread o C and P >>> PPS – Quick-Fasten connection o C and 7 >>> PPS – G 1 male thread o C and 8 >>> PPS – 3/4" NPT male thread o B and 6 >>> PPS – G 1 1/4 male thread o B and E >>> PPS – 1” NPT male thread o D and U >>> Brass – G 1 1/2 male thread o D and 0 >>> Brass – 1½" NPT male thread o D and M >>> Stainless steel – G 1 1/2 male thread o D and Y >>> Stainless steel – 1½" NPT male thread o E and X >>> Brass – G 2 male thread o E and 9 >>> Brass – 2" NPT male thread o E and O >>> Stainless steel – G 2 male thread o E and Z >>> Stainless steel – 2" NPT male thread

Approval Holder:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102725

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

TERAL, model, size & technical information on date label on body. Flow arrow on cover.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

MS(m)XXX-XX-E 1.m: different phase. --m: single phase, none: three phases 2.XXX: Rated flow (L/min) 3.XX: Rated power(kW). 4.E: E type end connection mode and size -- Rated flow(70-120m3/h): G1¼"XG1" -- Rated flow(210m3/h): G1½"XG1¼" -- Rated flow (370 m3/h): G2"XG1¼ AM(E) XXxXX (B) X/X-X XX(S) 1. E: Intelligent Type 2. XX: Inlet diameter (mm), range: 25,32,40,50 mm. 3. XX: Outlet diameter (mm), range: 25,32,40,50 mm. 4. B: alternative pump group 4. X/X: number of impeller /number of smaller impeller (if any) 5. X: motor frequency 6. XX: Rated power(kW) 7. S: different phase (S: single phase, none: three phases.)

Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250902720

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN25 - DN200 flanged.

Marking:

Dooch, model, serial number and technical info on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Proviso:

The discharge from the drain core must be made via a type AA, AB or AD air gap, or in accordance with EN 1717.

Model:

XRLNa-b-c-d Where: XRL = model. With N = Wetted metallic material in SUS316L, Without N = Wetted metallic material in SUS304. a = Rated flow in m³/h (1 – 255). DN25 = 1-3. DN32 = 4-5. DN40 = 10. DN50 = 15-20. DN65 = 32. DN80 = 45. DN100 = 64 or 95. DN150 = 125-155. DN200 = 185-255. b = Number of impellers (stages 1 – 36). DN25 & DN32 models with 1 – 36 stages. DN40 models with 1 – 22 stages. DN50 models with 1 – 17 stages. DN65 models with 1 – 14 stages. DN80 models with 1 – 13 stages. DN100 models with 1 – 8 stages. DN150 models with 1 – 10 stages. DN200 models with 1 – 8 stages. c = Number of cutting impellers (0 – 3). (Note: c can be omitted when c = 0.) d = DN size (DN25 – DN200). (Note: d can be omitted.) E.g., XRL32-7-2-DN65 denotes: Pump is made of SUS304, rated flow 32 m³/h, 7 impellers, 2 cutting impellers and size DN65.

Approval Holder:

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Company Name

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Address

No 239 Zhangliantang Rd Liantang Ind Park Qingpu District Shanghai City China

View All Listings by this Company

Manufacturer:

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Company Name

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Address

NO 669 DAYANG ROAD KANGSHAN STREET HUZHOU ZHEJAING CHINA

View All Listings by this Company

Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250904702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Wilo, made in Korea, Model No., Serial No., website address, & other tech info on data label. Wilo printed on control panel.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Model:

PBI-L203EA - Suction 25A(1”) Discharge 25A(1”) PBI-L204EA - Suction 25A(1”) Discharge 25A(1”) PBI-L205EA - Suction 25A(1”) Discharge 25A(1”) PBI-L402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-L803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD203EA - Suction 25A(1”) Discharge 25A(1”) PBI-LD402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) 1 - Series PBI-L: Electronic Boosting Pump Variable Speed Pump(Inverter Pump). 2 - Number of Pumps None/blank : Single Type (One Pump), D: Duplex Type (Two Pumps). 3 - Rated Flow capacity 2 : 2㎥/hr, 4 : 4㎥/hr, 8 : 8㎥/hr. 4 - Number of Impellers 02 : 2 Impellers, 03 : 3 Impellers, 04 : 4 Impellers, 05 : 5 Impellers. 5 - Power 60Hz L: 110V ~, J: 120V ~ , 127V~, M: 220V~ D: 110V/220V~, I: 220/380V 3~, T: 220V 3~, U: 380V 3~, N: 440V 3~, R: 480V 3~. 50Hz Z: 110V ~, C: 120V ~, 127V~, E: 220V ~, F: 110V/220V ~, G: 220/380V 3~, H: 220V 3~, Q: 380V 3~, Y: 440V 3~. 6 - Automatic mode. None/blank : non automatic models A: models which equips themselves with components that are responsible for automatic mode.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Range of overhead shower heads and arms incorporating a brass or ABS plastic body. The inlet of models KSAB4K and HEAH06BK incorporates a stainless-steel strainer and plastic flow regulator. Model EKIT01/A is a shower kit consisting of a shower hose, handset and riser rail and model AIR1HSCPWHUK shower handset only. Open outlet use only. Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

251204004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SEE MODELS.

Marking:

KSABK : Methven, DTC 15,DEVA etched on shower face, joint. HEAH06: DTC 15, DEVA etched on joint EKIT01/A : Methven etched on hand shower.

Installation Requirements:

R001 R040

Expiry date:

31/12/2030

Model:

KSABK ½” BSP (M), HEAH06 ½” BSP (F), AIR1HSCPWHUK ½” BSP (M), EKIT01/A ½” BSP (F).

Approval Holder:

Methven UK Limited

Company Name

Methven UK Limited

Address

Methven Experience Centre 3-3A Stone Cross Court Yew Tree Way Golborne Warrington

Postcode

WA3 3JE

Country

United Kingdom

Phone

0800 195 1602

General Email

raluca.olariu@uk.methven.com

View All Listings by this Company

Range of Y-patterned strainers with brass bodies and a stainless-steel mesh strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” - 4” BSP (F)x(F).

Marking:

Herz "heart" logo on plug. PN, DN &flow arrow on body.

Installation Requirements:

R001 R120

Expiry date:

30/06/2030

Model:

2 2662 01 - DN15 2 2662 02 - DN20 2 2662 03 - DN25 2 2662 04 - DN32 2 2662 05 - DN40 2 2662 06 - DN50

Approval Holder:

Herz Armaturen GmbH

Company Name

Herz Armaturen GmbH

Address

Richard - Strauss Strasse 22, A-1230, Vienna

Country

Austria

View All Listings by this Company

Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2”, 3/4”, 1”, 1-1/4”, 1-1/2” & 2” BSP (F)

Marking:

Manufacturers logo (H), size, pressure rating and flow arrow on body. Product info on data plate.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

F2143W

Approval Holder:

TECOFI

Company Name

TECOFI

Address

2 Rue Barthélemy Thimonier ZAC Everest Lyon

Postcode

69740

Country

France

General Email

j.ortega@tecofi.fr

View All Listings by this Company

Manufacturer:

Ningbo Yongxiang Copper Pipeline Co. Ltd

Company Name

Ningbo Yongxiang Copper Pipeline Co. Ltd

Address

Hehua Bridge, Yunlong Town, Yinzhou District, Ningbo, China

General Email

View All Listings by this Company

Manufacturer:

Ningbo Yongxiang Copper Pipeline Co. Ltd

Company Name

Ningbo Yongxiang Copper Pipeline Co. Ltd

Address

Hehua Bridge, Yunlong Town, Yinzhou District, Ningbo, China

General Email

View All Listings by this Company

Range of in-line Y patterned strainers with bronze bodies and a stainless-steel mesh strainer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

Honeywell logo, PN & Size on bonnet. Size, DN & flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/04/2030

Model:

V3-YST-A150-B015N. :1/2” V3-YST-A150-B020N. :3/4” V3-YST-A150-B025N. :1” V3-YST-A150-B032N. :1-1/4” V3-YST-A150-B040N. :1-1/2” V3-YST-A150-B050N. ：2”

Approval Holder:

Honeywell International Middle East

Company Name

Honeywell International Middle East

Address

EMAAR BUSINESS PARK 1st St Dubai

Country

United Arab Emirates

General Email

Mona.Ali@Honeywell.com

View All Listings by this Company

GYS20/W Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2”, 3/4”, 1”, 1-1/4”, 1-1/2” & 2” BSP (F)

Marking:

Company logo SHIELD, size, pressure rating and BS5154 on body. Product info on data plate.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

GYS20/W

Approval Holder:

SHIELD FIRE SAFETY & SECURITY LTD

Company Name

SHIELD FIRE SAFETY & SECURITY LTD

Address

Unit 3, Endeavour Drive Basildon- Essex

Postcode

SS14 3WF

Country

United Kingdom

Phone

+44 (0) 1708 377731

General Email

info@shieldglobal.com

View All Listings by this Company

In-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 Bar Maximum operating temperature 85.0°C

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP F to 2” BSP F

Marking:

NINGBO HUACHENG logo, PN, size, flow arrow and date of manufacture (MMYY) on body. NINGBO HUACHENG logo, PN & SS304 on data plate.

Installation Requirements:

R001

Expiry date:

30/11/2030

Model:

GL409

Approval Holder:

Ningbo Huacheng Valve Co., Ltd

Company Name

Ningbo Huacheng Valve Co., Ltd

Address

103, East Road of the Station Huangtan Town, Ninghai County, Ningbo.

Postcode

315699

Country

China

General Email

jianluo@huachengvalve.com

View All Listings by this Company

Range of draining taps, straight or elbowed with brass bodies incorporating a rising spindle headwork. Maximum working pressure 10.0 Bar Maximum operating temperature 95.0°C

Section:

1770 Taps

Section Subtitle:

Draining, for above ground use only.

WRAS Approval Number:

250702056

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

South Coast Sales logo and size on body. size and EN1254 on compression nut

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

BF8712 Elbow Drain off Mi x C Compression x Male 3/4”Mx 21mm BF8713 Elbow Drain off Mi x C Compression x Male 1”M x 27.4mm BF4712 Elbow Drain off compression 21mm x 21mm BF4713 Elbow Drain off compression 27.4mm x 27.4mm BF1711 Straight Drain off compression 14.7mm x 14.7mm BF1712 Straight Drain off compression 21mm x 21mm BF1713 Straight Drain off compression 27.4mm x 27.4mm

Approval Holder:

South Coast Sales

Company Name

South Coast Sales

Address

1 Doughcloyne Industrial Estate, Sarsfield Road, Wilton, Cork.

Postcode

T12 TR62

Country

Ireland

Phone

00353 21 - 43 46 143

General Email

info@southcoastsales.com

View All Listings by this Company

Section:

1800 Taps

Description:

A Range of Pillar tap(s).

Deck mounted Capable of achieving AUK2 Tap gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005

Expiry date:

31/01/2031

Notes & Further Information

X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: F – Cross Top Type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD

Section:

1800 Taps

Description:

A Range of Pillar tap(s).

Deck Mounted. Capable of achieving AUK2 Tap Gap.

Installation Requirements:

R001 R005

Expiry date:

31/01/2031

Product Images

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of pillar taps, incorporating a non-rising spindle headwork with cross top or dome type operating members. The spout outlet incorporates a plastic flow straightener, and the product is supplied with metal back nuts. All taps will be supplied with an optional Flow Regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1800 Taps

Section Subtitle:

Pillar tap(s).

WRAS Approval Number:

250288005

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M)

Marking:

ebb + flo on body

Installation Requirements:

R001 R006

Expiry date:

28/02/2030

Model:

52398 & 64284. All taps will be supplied with an optional Flow Regulator.

Product Images

Approval Holder:

Toolstation Ltd.

Company Name

Toolstation Ltd.

Address

Travis Perkins PLC Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

Range of wall or floor mounted, self-closing taps (brass or chromium plated brass) with spring loaded headworks and either dome type, foot pedal or stick operating members. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.

Section:

1820 Taps

Section Subtitle:

Self closing tap(s).

WRAS Approval Number:

251202001

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm Compression Fitting (910000) ½” BSP M (All other Models)

Marking:

MCM and model number on body or cap

Installation Requirements:

R001 R040

Expiry date:

31/12/2030

Model:

910000 900505 900500 900600 908500 908600 905600 905700 900406

Manufacturer:

Rubinetterie MCM Intl. Srl.

Company Name

Rubinetterie MCM Intl. Srl.

Address

Via Dell'Acacia 54/56 I-28021 Borgomanero Italy

View All Listings by this Company

Range of chromium plated stainless steel or brass interlocked shower hoses with an optional PVC outer layer. Incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

2106064

Note:

Open outlet use only.

Size:

½” BSP Captive nut inlet x outlet.

Marking:

Intatec logo on conical nut.

Installation Requirements:

R001

Expiry date:

30/06/2026

Model:

IX100005CP - 1.5M BRAIDED IX100004CP - 1.5M SMOOTH 30003CPX - 1.5M BRAIDED IX100006CP - 2M BRAIDED 30006CPX - 2M BRAIDED

Approval Holder:

Intatec Limited

Company Name

Intatec Limited

Address

Airfield Industrial Estate Hixon Staffordshire

Postcode

ST18 0PF

Country

United Kingdom

Phone

01889272180

General Email

ryan.tilsley@intatec.co.uk

View All Listings by this Company

FLEXCORE range of stainless steel and polyamide braided flexible polyethylene lined hose assemblies with various end connections. For use with copper pipe to EN1057 Maximum working pressure:10 bar Maximum operating temperature:70°C

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

250902017

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

Neoperl, ZZ represents manufacturer, Pressure, temperature, production date and WRAS on ferrule

Installation Requirements:

R001 R008

Expiry date:

30/09/2030

Model:

39.06CD.EFG.HI: Hose: DN8 Manufacturer where ZZ represents 2Z - NPJM - Neoperl Faucet Components (Jiangmen) Co., Ltd. 3Z - Nordic - NEOPERL Nordic A/S 4Z - NPI Italia - NPI Italia Srl 5Z - NPBG - Neoperl Bulgaria EOOD 6Z - NPIN - NEOPERL, INC. 7Z - NPAP - Neoperl Asia Pacific Co., Ltd. Connection Sizes: Female elbow ⅜, ½, ¾ Female straight ⅜, ½, ¾, 7 /16, 9 /16 Tube ø8 - ø10 Male M8 - M15 Male straight ⅜ , ½ , ¾ , 7 /16 , 9 /16 Comp. joint ø8 - ø12 Plugin D8 - D13 Part Code nomenclature constructed in the following manner: - 39.ABCD.EFG.HI A = Hose Type (supply hose, outlet hose, shower hose etc.) B = Hose (inliner) Material CD.EFG = Manufacturing sequential number HI = Packaging information

Manufacturer:

Neoperl GmbH

Company Name

Neoperl GmbH

Address

Klosterrunstrasse 9-11, Müllheim

Postcode

D-79379

Country

Germany

Phone

+49 7631 188 374

View All Listings by this Company

502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. For non-potable water use only. Maximum working pressure 10.0 bar. Maximum operating temperature see models.

Section:

1980 Valves

Section Subtitle:

Air venting. Fittings in this section are suitable for above ground installations only.

WRAS Approval Number:

260104002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Caleffi logo on body.

Installation Requirements:

R001 R200

Expiry date:

31/01/2031

Model:

502930 TH 3/8" 110°C 502934 CST 3/8" 110°C 502420 1/4" 115 °C 502430 3/8" 115 °C 502430 CON 3/8" 115 °C 502430 CST 3/8" 115 °C 502431 BSC 3/8" 115 °C 502434 CST 3/8" 115 °C 502435 CST 3/8" 115 °C 502530 TH 3/8" 110°C 502530 TH1 3/8" 110°C 502641 3/8" 115°C 502643A 1/2" NPT 115°C 502533 3/8" 110°C 502533 FRT 3/8" 110°C 502533 TAK 3/8" 110°C 502543 3/8" 110°C 502533 RIF 3/8" 110°C 502530 3/8" 110°C 502141 1/2" 110 °C 502142 1/2" 110 °C 502145 RIF 1/2" 110 °C 502145 RSR 1/2" 110 °C 502630 3/8" 115°C 502630 CST 3/8" 115°C 502636 CST 3/8" 115°C 502638 CST 3/8" 115°C 502638 OEM 3/8" 115°C 502631 CST 3/8" 115°C 502822 1/4" NPT 502620A 1/4" NPT 115°C 502610A 1/8" NPT 115°C 502630 WLF 3/8" 115°C 502634 CST 3/8" 115°C 502640 1/2" 115°C 502649 1/2" 115°C 502649 CST 1/2" 115°C 502730 3/8" 110°C 502730 CST 3/8" 110°C 502730 BSC 3/8" 110°C 502730 NTR 3/8" 110°C 502710A 1/8" NPTF 110°C 502720A 1/4" NPTF 110°C 502030 3/8" 120 °C 502030 CON 3/8" 120 °C 502030 CST 3/8" 120 °C 502035 CST 3/8" 120 °C 502037 CST 3/8" 120 °C 502037 VLL 3/8" 120 °C 502037 WLF 3/8" 120 °C 502038 CST 3/8" 120 °C 502020 CST 1/4" 120 °C 502034 CST 3/8" 120 °C 502130 3/8" 110 °C 502031 3/8" 120 °C 502130 TH1 3/8" 110 °C 502033 CST 3/8" 120 °C 502015A 1/8" NPT 120 °C 502015 B&G 1/8" NPT 120 °C 502015A WEB 1/8" NPT 120 °C 502015 MTR 1/8" NPT 120 °C 502040A 1/2" NPT 120 °C 502040A WEB 1/2" NPT 120 °C 502043A 1/2" NPT 120 °C 502043A CST 1/2" 120 °C 502044 CST 1/2" 120 °C 502040 1/2" 120 °C 502040 CST 1/2" 120 °C 502043 1/2" 120 °C 502043 CST 1/2" 120 °C 502140 1/2" 110 °C 502140 FRT 1/2" 110 °C 502041 1/2" 120 °C 502041 MI 1/2" 120 °C 502046 IMM 1/2" 120 °C 502221 1/4" 120°C 502231 3/8" 120°C 502231 CST 3/8" 120°C 502232 TH 3/8" 120°C 502241 1/2" 120°C 502243A 1/2" NPTF 120°C 502343A 1/2" NPTF 120°C 502246 IMM 1/2" 120°C 502242 TH 1/2" 120°C 502115A 1/8" NPT 110 °C 502133 3/8" 110 °C 502131 3/8" 110 °C 502131 TH 3/8" 110 °C 502132 DEC 3/8" 110 °C 502130 CST 3/8" 110 °C 502130 FRT 3/8" 110 °C 502130 TAK 3/8" 110 °C 502130 TH 3/8" 110 °C 502135 RIF 3/8" 110 °C 502050 3/4" 120 °C 502051 3/4" 120 °C 502052 CST 3/4" 120 °C 502060 1" 120 °C 502055 120 °C 502061 1" 120 °C 502067 1" 120 °C 502400 CST Press fitting ø22,2 customer designed 115 °C 501500 3/4" 120 °C

Approval Holder:

Caleffi S.p.A

Company Name

Caleffi S.p.A

Address

Strada Regionale 229 n. 25 Fontaneto d'Agogna (NO)

Postcode

28010

Country

Italy

Phone

+39 0322 8491

General Email

gary.perry@caleffi.com

View All Listings by this Company

Section:

2000 Shower Valves

Description:

A Range of Shower valve(s) with manual temperature control.

Wall mounted concealed Undefinable Air Gap - See IRN's

Installation Requirements:

R001 R010 R040

Expiry date:

31/01/2031

Notes & Further Information

Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturers:

Hansgrohe SE

Range of wall mounted, or concealed manually operated blending valves, (brass body, chrome finish), incorporating a ceramic cartridge headwork controlling both the flow and temperature with a single lever operating member. Maximum working pressure 5 bar. Maximum operating temperature 85°C.

Section:

2000 Shower Valves

Section Subtitle:

Shower valve(s) with manual temperature control.

WRAS Approval Number:

250488011

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm Compression

Marking:

ebb+flo on body

Installation Requirements:

R001 R010 R040

Expiry date:

30/04/2030

Model:

35346

Approval Holder:

Toolstation Ltd.

Company Name

Toolstation Ltd.

Address

Travis Perkins PLC Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company