Spring loaded resilient trim, in-line check valve cartridge with plastic guides and stem and EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Range of wall mounted, two-hole, single outlet (fixed) combination taps assemblies (brass bodies - in various finishes), incorporating ceramic cartridge headworks with various operating members. The spout outlets incorporate plastic aerators. The inlet of the spout outlets incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating three quarter turn ceramic disc headworks controlling the flow and temperature with cross top operating members and a manually operated diverter to shower outlet with cross top operating members. Model T2DB is supplied with a shower handset and hose and model B2TDS is supplied with a shower pipe and arm. The spout outlets incorporate a plastic aerator or flow straightener. Products are supplied with metal backnuts. The inlets incorporate an approved check valve cartridge however, the complete products have not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks controlling the temperature with cross top operating members and a manually operated diverter to shower outlet controlling the flow with cross top operating members. The product is supplied with a shower pipe and arm. The spout outlets incorporate a plastic aerator or flow straightener. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with single lever operating member and a lockable self-cancelling diverter to shower outlet. The spout outlet incorporates a flow straightener or optional aerator. Both the shower outlet (from the main body) and the inlet to the shower handset incorporate Incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
‘Epsilon Series’ polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Aquaflow polypropylene bodied compression fittings with EPDM ‘O’-rings for use with Elysee PE80 blue pipes. The fittings are supplied with a pipe liner. Above and below ground use. Maximum working pressure 12.5 bar. Cold water use only.
Range of press fittings incorporating brass or PVDF bodies and EPDM ‘O’-rings. For use with Henco standard PE-Xc/AL/PE-Xc pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘Comisa’ range of brass bodied press-fit and threaded fittings for use with `Comisa’ (PE-RT/AL/PE-LMD) multi-layer pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of ‘Henco Profit Synthetic’ pushfit fittings with PPS (HPK models) or brass (HP models) bodies and EPDM o-rings, to be used with ‘Henco RIXc’ PEXc/Al/PEXc multilayer pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of Easytec press fittings for use with Easytec multilayer (Pe-rt/Al/Pe-rt) pipe. Hewing range of ‘Easytec’ Multilyer Composite Pipe and Press Fitting system with brass press fittings with stainless steel sleeves incorporating EPDM o-rings. 16mm to 32 mm are LBP fittings and from 40mm to 63 mm are standard fittings. Joints are achieved via TH profile press tool. Maximum working pressure: 10bar Maximum working temperature: 95°c
Range of Gerpex press fittings for use with Alpert multilayer (Pe-rt/Al/Pe-rt) pipe. Alpert Multilyer Composite Pipe and Press Fitting system with brass press fittings with stainless steel sleeves incorporating EPDM o-rings. 16mm to 32 mm are LBP fittings and from 40mm to 63 mm are standard fittings. Joints are achieved via TH profile press tool. Maximum working pressure: 10bar Maximum working temperature: 95°c
Range of 'PF Press' TH Profile Brass Press Fittings for use with 'PF Press' Pert-al-Pert Multilayer pipe manufactured to EN ISO 21003 in sizes 16mm, 20mm, 26mm and 32mm. Maximum working pressure 10 bar. Maximum operating temperature: 16mm & 32mm - 95°C. 20mm & 26mm - 23°C between May 2023 to November 2023 and 95°C December 2023 onwards.
Range of MM and MC press fit fittings with PPSU bodies incorporating stainless steel crimp sleeves and EPDM O-Rings for use with AIS XPERT multi-layer pipes. Maximum working pressure is 10.0 bar. Maximum operating temperature is 70°C.
Supreme S16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Elysee range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Jason range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
‘Mapress’ range copper or copper and brass “copper-press” fittings with butyl rubber (up to 54mm) or EPDM rubber (>54mm) ‘O’-rings for use with copper pipe to BS EN 1057. For above ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of water meter manifolds with a plastic body and a spherical valve at the inlet. Models MB2012525DM & MB2010303DM incorporates two single check valve cartridges, all other models incorporate one single check valve however, the complete product has not been fully tested to demonstrate it provides backflow protection Model MB201010BM is for use with Irish Heavy gauge pipe manufactured to 15134/1977. All other models are for use with blue MDPE pipe manufactured to EN12201. Maximum working pressure 12.5 bar. Cold water use only.
Range of circulation fittings with gun metal bodies, plastic cones & guides and EPDM ‘O’ rings. The products incorporate a dynamic venturi valve. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Concealed wall mounted rough inset with a brass body, incorporating EDPM O-rings. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of black plastic bodied multistage, self or manually primed, high pressure centrifugal pumps with a stainless steel outer casing, plastic impellors, EPDM seals and ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of wall mounted hose union taps (brass, chrome plated brass or DZR brass body) incorporating a non-rising spindle headwork with a butterfly handle operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
502 series of automatic air venting valves with brass bodies, plastic float and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 115°C. Model added September 2021 (501500) has a maximum operating temperature of 120°C. All other models have a maximum operating temperature of 115°C.
Range of manually adjustable pressure reducing valves with DZR brass bodies and EPDM ‘O’- rings. Maximum inlet pressure 15.0 bar, adjustable outlet range of 2.2 to 4 bar. Maximum operating temperature 60°C.
Range of in-line, pressure reducing valves with DZR brass bodies and stainless-steel strainers. Maximum inlet supply pressure 16.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 45°C or 65°C, please refer to model.
Range of pre-set angled pressure relief valves for use on primary closed circuits, incorporating DZR brass bodies, EPDM diaphram and EPDM or NBR ‘O’-ring. For maximum working pressure please refer to model. Maximum operating temperature 99°C.
Range of spherical valves with nickel plated brass bodies, chromium plated brass balls, PTFE seals, NBR and/or FKM ‘O’-rings. 140, 140M, 141 & 141M series models incorporate a stainless-steel strainer. 140 & 141 series models also incorporate a magnet. The 121 & 122 series models are 3-way valves. Maximum working pressure: See PN in brackets under model. Maximum operating temperature: Cold water use only.
Range of gate valves incorporating bronze bodies and wedges with PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with a non-rising spindle and a handwheel operating member with a brass body and brass wedge. Maximum working pressure 17.5 Bar Maximum operating temperature 93.0°C
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of stop valves with either DZR brass, brass, bronze or chrome plated bodies with T-type or lockshield (LS) operating members. Compression models are for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stop valves withbreonze, brass or chrome plated brass bodies, EPDM and PTFE washers incorporating a T type or lockshield operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C
Range of screw down stop valves with plastic bodies to be used with PEX, MDPE and copper pipe. For above ground use only. Maximum working pressure 16.0 bar, cold water use only.
Range of screw down stop valves with plastic bodies, EPDM washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). The products are supplied with loose pipe inserts. For above and below ground use. Maximum working pressure 16 bar. Cold water use only.
'Dicoat Medium Temp Black'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/2019100121', issue no. '01' dated 08.07.2020. Cure for 7 days@30°C. Between 1st January 2021 to 22nd November 2021, the material is for use with water up to 50°C. Between 23rd November 2021 and 31st January 2026, the material is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 modified bitumen anticorrosive coating`. Factory applied, black coloured bituminous coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'Kubotaseal BM'. Factory applied, black coloured asphaltic bituminous coating. Apply as per manufacturer's PDS reference `11004T-1.4' dated Feb, 20, 2020. Cure 6 hours@20°C. For use with water up to 60°C. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'YS-01 Powder Coating'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instruction document 'HJ-Q-SOP-05' dated 2020-1-10. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'XX-CM2'. Factory applied, grey coloured cement mortar. Mix and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'EDELPOXY FN 132 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's IFU reference 'PC 132' dated 'January 28, 2020'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC4'. Factory applied, clear PTFE coating, intended for use with `O` rings, seals & gaskets. Apply as `Superior Group Quality Management System Procedure Reference 8.6’ referenced in document `LDAP-008 issue 1` released 01/05/2020. For use with water up to 85°C
'BSS-P'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction's 'BSS-D0001' dated '2020-12-10'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'High Build Solvent Free Epoxy Coating Red'. Factory applied, red coloured epoxy coating. Apply as per manufacturer's user instructions reference 'SPL/RD/UI/202006119', issue no, '01' dated 20.08.2020. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HSXX CM-1'. Factory applied, grey coloured cement mortar. Mix, apply and cure as per manufacturer's Technical Data Sheet issue number '001' dated '2020.08.01'. For use with water up to 65°C.
'Vastcoat MT'. Factory applied, blue coloured thermoplastic powder coating. Apply as per manufacturer's instructions 'Issue number 02000202710' dated 20.02.2020. Cure for 10 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ever-Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's TDS '20200801 A1'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Edelpoxy FN 132 Blue Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions dated 'January 28, 2020'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LDP-800 (1009GBSDT)' - white coloured & 'LDP-800' - blue coloured. Factory applied, fusion bonded epoxy powder coatings. Apply as cure as per manufacturer's user instructions file no. 'NP200917', 'version 1', dated 'Sep, 17, 2020'. For use with water up to 85°C.
'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
`3011 high chlorinated polyethylene anticorrosive coating`. Factory applied, burgundy coloured polyethylene coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per Technical Data Sheet file no. 'TWJ-H-453', edition 'A2', dated '01/03/2020'. Cure for 5 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 Epoxy anticorrosive coating`. Factory applied, black coloured epoxy coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18, 2020. For use with water up to 23°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
'KD-002'. Factory applied, blue coloured powder coating. Apply and cure as per manufacturer's instructions file number 'KD-1230-20', version 'A0', dated '2020-12-30'. For use with water up to 23°C.
'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'FIBER TECH 80, Low VOC fiberglass resin'. Factory applied, brown coloured polyester resin & fibreglass. Apply as per manufacturer's method statement reference 'PP-GRP-092021-R1' dated '21 Sept. 2020'. Cure for 48 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5108-M'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's user manual 'edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Endoprene 888.56'. Factory applied, beige coloured, two-part PU coating. Mix Parts A & B in a 75:25 volume ratio and apply as per Technical Data Sheet dated 09/12/2020. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Art-Coat'. Factory applied, colourless (transparent) PTFE based surface treatment coating. Apply as per manufacturer's instructions 'revision 3' dated 16-03-2020. Cure for 45 minutes@55-60°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FP60 Dark Blue'. Factory applied, dark blue coloured epoxy powder coating. Mix and apply as per manufacturer's TDS 'FP60/Rev:3' October 2020. Cure for 10 minutes@160°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HKUST002'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'HKUST002101001', '01', dated '03/11/2020'. Cure for 168 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Brushbond FLXIII'. Site applied, grey coloured, two-part elastomeric/cementitious coating. Mix and apply in accordance with manufacturer's instructions 'v10' dated October 2020. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White'. Site applied, two-component, white coloured epoxy coating. Mix part A (off-white white coloured liquid) and part B (off-white coloured liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions ref. '2252', issue date 17/12/2020. Cure for 7 days@25°C. Between January 2022 and August 2022, the coating was for use with water up to 23°C. Between September 2022 and January 2027, the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Interline 925 Cream'. Site applied, cream coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (yellow liquid) in a volume ratio of 3:1 and apply as per manufacturer’s TDS ref. ‘2252’ dated 17/12/2020. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tiefill'. Site applied, grey coloured cementitious repair mortar. Mix Tiefill with water in a weight ratio of 9.4:1 and apply in accordance with manufacturer’s instructions for use 'bulletin no. TFILL/031/003, issued 'July 2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BÜFA®-ISO-Gelcoat 3000-H 572-9735 & Synolite 5410-P-4'. Grey coloured, unsaturated polyester gelcoat with a hand-laid unsaturated polyester resin and fibreglass laminate. Apply and cure in accordance with manufacturer's user guides 'Q-035, issue 1' & 'BUKUG 1001, issue 1' dated 19/08/2020. For use with water up to 23°C.
'Grilon BG-30/2 natural (appears cream in colour) & Grilon BG-30/2 black 9697 (black coloured)'. Injection moulded PA-GF30 materials. Grilon BG-30/2 black 9697 is for use with water up to 85°C. Between 1st October 2020 and 10th May 2022, Grilon BG-30/2 natural was for use with water up to 23°C. Between 11th May 2022 and 31st October 2025 Grilon BG-30/2 natural is for use with water up to 60°C.
‘VP1620-WR & VP-2020-WR’. Single layer, cream coloured, extruded PEX-b tubes. For use with water up to 85°C.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'STRONGHOLD SH-EP3'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ME2020/80 Grey'. Grey coloured, injection moulded VMQ sheet material. Shore hardness 80. Tested in-radius 1.0mm. For use with water up to 85°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Griffon WDF-05'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6311380 20200708'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of spring loaded resilient trim check valve cartridges with a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of spring loaded resilient trim check valve cartridges with plastic bodies. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of tundishes incorporating a black or grey plastic body or mild steel painted black body (128-2001 CST, 128-2003 CST, 128-2004 CST & 128-2005 CST models only). Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Range of vertical and horizontal expansion vessels with EPDM membrane and stainless steel or galvanised steel connections. Maximum working pressures 10.0. Maximum operating temperature 85 °C.
Fluxo range of Brass & PPSU crimp fittings for use with ‘Fluxo’ PEX/Al/PEX Multilayer Pipe. Crimp joint is achieved by a TH profile crimp jaws. Maximum working pressure 10bar @ 70°C, 6Bar @ 95°C.
Range of AIS tin-plated brass and PPSU press fit fittings for use with WRW & 'Maincor MLC’ multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Press (TH press profile) and screw/compression fittings with brass bodies for use with Comisa Evo Pipe (PE-RT/AL/PE), for above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of AIS tin-plated brass and PPSU press fit fittings for use with MULTIPIPE multi layered PE-RT/AL/PE-RT pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
‘APL’ & 'AP' ranges of brass press fittings for use with ‘APE Multylayer' pipe. Connection is achieved via TH or U profile press jaws. AP range, only TH profile; APL range, TH and H profile; TH and H profile from DN 16 to DN32; TH for DN40, DN50 and DN63. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Range of stainless steel press fittings to be used with stainless steel pipes. Connection is achieved via M profile press jaws. For above ground and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Hyddro press fittings incorporating EPDM ‘O’-rings. For use with Hyddro (S-1-0509/10/11/12/17/13) PEX-AL-PEX pipe. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C
‘Tweetop system’ consisting of brass bodied nickel plated, compression or press fit (‘U’ crimping profile) fittings for use with ‘Tweetop multilayer pipe’ PERT/AL/PERT. Maximum working pressure 10.0 Bar. Maximum working temperature 95°C.
‘Hetta system’ consisting of brass bodied nickel plated, compression or press fit (‘U’ crimping profile) fittings for use with multilayer pipe PERT/AL/PERT. Maximum working pressure 10.0 Bar. Maximum working temperature 95°C.
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘Tweetop LBP system’ consisting of brass bodied press fittings for use with ‘Tweetop multilayer pipe’ PE-RT II/AL/PE-RT II. The press fitting is achieved by use of a press fitting tool (‘U’ or ‘TH’ crimping profiles). Maximum working pressure: 10.0 Bar. Maximum working temperature: 95°C.
Instinct range of U profile press fittings (nickel plated brass bodies) for use with Instinct range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘ZL’ range of U profile press fittings (nickel plated brass bodies) for use with ‘ZL’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
SAB A16 range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
FloPlast "Supreme" range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
NORMA MARLIN range of fittings for use with PE pipes (manufactured to EN12201-2). Supplied with a plastic pipe support liner For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
‘Hansen easy fit’ range of polypropylene compression fittings with EPDM ‘O’-rings for use with metric PE80 (20mm-63mm) and PE100 (32mm-110mm) pipe to AS/NZS:4130 and plastic pipe inserts. For above and below ground use. Maximum working pressure: See models. Maximum operating temperature: Cold water use only.
IDC ‘BDGxxx’ range of press fittings with brass or nickel plated brass bodies (see model) incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). The BDG241 and BDG257 prefix models incorporate an EPDM gasket on the captive nut end connection. Pressfit jointing is achieved by either a U or TH crimping profile. Compression connections are for use with copper pipe 12-28mm (manufactured to EN1057) or Irish copper pipe 14.7-27.4mm (manufactured to EN1057). For above ground use only. Maximum working pressure 10.0 bar. 20, 25 & 26mm pressfit sizes cold water use only. Threaded, compression and 16 & 32mm pressfit sizes maximum operating temperature 95°C. From June 2025: The 20, 25 & 26mm pressfit sizes (TH profile only) maximum operating temperature 95°C.
Press-Inox range of stainless-steel crimped fittings (‘M’ crimp profile) for use with stainless steel pipe (manufactured to EN10204). For above ground use only. Maximum working pressure: 16Bar. Maximum operating temperature: 100°C.
`Prox’ and ‘Wave` ranges of sensor operated flow control devices incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C
Range of wall mounted hose union bib taps incorporating a rising spindle headwork with a T - handle operating member. Model 13.20202.G15.CP5R-8511 has a DZR brass body, all other models have a brass body. Model 13.20252.G15.CP5R-8510 incorporates a lockshield device at the base of the operating stem. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating quarter turn ceramic disc headwork and a two-way, half-turn ceramic disc manual diverter for dual outlet models. The inlets incorporate a stainless-steel strainer & an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of pressure relief valves with DZR brass bodies incorporating EPDM diaphragms. The valves are pre-set as follows: 311560, 312469, 312461ITH, 311461CTS,531661 CST models: 6.0 bar, 312471 CST model: 7.0 bar, 312020 CST model: 10.0 bar. Maximum operating temperature 99°C.
Range of pre-set pressure relief valves incorporating DZR brass bodies and an EPDM diaphragms and PTFE washers. The valve is fitted with hand operated rotating easing gear. Maximum working – see model. Maximum operating temperature 85°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C
Range of spherical valves with stainless steel bodies, incorporating PTFE seats and a lever t operating member. Maximum working pressure: 68 Bar. Maximum operating temperature: 100°C
Range of screwdriver operated spherical valves with a brass body and either a chrome plated brass ball (4000120555 model) or brass ball (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of non-rising spindle lock shield gate valves with DZR brass bodies. Maximum working pressure 16 bar. Maximum operating temperature: 65°C Maximum working pressure 10 bar. Maximum operating temperature: 82°C
Range of gate valves with brass bodies and wedges. Maximum working pressure 17.5 bar. Maximum operating temperature 93°C
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves operate via a non-rising spindle and are supplied with either no operating member or a hand wheel (see models) Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Wanan brand WA F 501'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Wanan Industry Group Co., Ltd.' TDS 'WATDS20200801a' dated 'Aug. 1, 2020'. Cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SWEP Sealix Coating'. Factory applied, colourless (translucent) silicon dioxide coating. Apply as per manufacturing instructions ref. 'Sealix-2020-01' dated 2020-01-01. Cure for 3 hours@300°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'Resicoat PI Brown'. Factory applied, brown coloured epoxy coating. Apply as per manufacturers datasheet dated March 4, 2020. Post-cure for 20 minutes@210°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
‘ME2020’ injection moulded components. Silicone rubber ‘O’ rings and gaskets available in red, blue, white, black, light grey colours. Shore hardness between 30 - 70. Tested in-radii sizes between 0.5mm and 5mm. For use with water up to 85°C.
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating a half turn ceramic disc headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Range of gate valves with brass bodies, brass wedges and PTFE gaskets. The valves are operated via a non-rising spindle with a hand wheel operating member. The Z2020.028 compression model is for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
