'NB70N-0203 Gasket'. Dark grey coloured, injection moulded NBR gasket. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C. When processing an application for WRAS Product Approval: The in-radius tolerance rule may be applied to the gasket, but only to gaskets and no other shape. This is the only shape of component covered by the approval.
'Lavelle BUR165'. Red coloured, transfer moulded, silicone rubber gasket. Shore hardness 40A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ELASTOSIL LR 3020/60 A+B' Natural (appears white, translucent) & 'ELASTOSIL LR 3020/60 A+B with 2% by weight ELASTOSIL Colour Paste FL Red Iron Oxide RAL 3013' (red coloured). Injection moulded silicone rubbers with a shore hardness of 60 ShA and a tested in-radius size of 0.9mm. For use with water up to 85°C.
'GFS Gas Flex Systems 543 Pipe Sealants'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/09/2022 v1.0'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Wiseman Everblue Jointing Compound'. Beige coloured jointing compound. Apply as per manufacturer's instructions '001/A2'. For use with water up to 85°C.
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of check valve cartridges with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of in-line, non-verifiable single check valve assemblies consisting of a spring loaded, resilient trim, single check valve cartridge housed within a DZR brass body. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies and NBR rubber `O`-rings, intended for insertion into specifically dimensioned bores. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Deck mounted side valve (brass body) incorporating a quarter turn ceramic disc headwork and cross top operating member. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of thermostatic cartridges with brass (some of which are chrome plated), stainless steel or plastic bodies, for insertion into specifically dimensioned bores. All models (except for models TWK-5T, TWK-13 and TPWK-26A) incorporate a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 85°C
Thermostatic cartridge with plastic body incorporating EPDM ‘O’-rings and stainless steel strainer. To be installed into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating either a ceramic cartridge headwork or ceramic disc headworks with various operating members (see model). The spout outlet of some models incorporates a plastic aerator (specific models only - see model). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies, various finishes - see model), incorporating either a ceramic cartridge headwork with a single lever operating member or ceramic disc headwork with cross top operating members (see model). The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of pillar taps, (chrome plated, brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum operating pressure 6 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (black or chrome plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks, with single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever type pop up waste (see models) Other models are supplied with a permanently open waste set. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a click type waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. This product is supplied with a click type pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies). Model 4E2318 incorporates a ceramic cartridge headwork with single lever operating member. Model 4E2319 incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a flow straightener and is also supplied with an optional aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of single hole, double outlet (swivel) combination tap assemblies (chromium plated brass). incorporating quarter turn ceramic disc headworks with single lever operating members or non-rising spindle headworks and dome type or cross top operating members (see model). The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, (brass bodies, various finishes - see model), incorporating a ceramic cartridge headworks with either a single lever operating member or dome type operating member (F9482A-X model only). Thee spout outlet incorporates a plastic aerator (except model F8122A). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole,wall mounted, concealed, tap assemblies, including spout outlet, trim set and single lever operating members (various finishes). The spout outlet incorporates a plastic flow straightener and a plastic flow regulator on the inlet. Maximum working pressure 10 bar. Maximum working temperature 60°C.
Wall mounted bath shower mixer with brass body (various finishes). Ceramic disc headwork with dome operating members, manually operated diverter to shower outlets. The temperature is controlled independently via a thermostatic cartridge using a single lever operating member. Both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Spout outlet incorporates a plastic aerator. Products are supplied with shower headhead, shower handset and shower hose. Maximum operating pressure 10 Bar. Maximum operating temperature 85°C.
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headwork with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a dome type operating member and a manual override button. Each inlet incorporates a combined NBR washer and stainless steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self cancelling diverter to shower outlet and a plastic flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
A wall mounted two-hole, single outlet, fixed combination tap assembles (brass body – various finishes). Incorporating quarter turn ceramic disc headwork with single lever operating members and a self-cancelling diverter to a shower outlet. The temperature is controlled independently via a thermostatic cartridge. Both operating members incorporate a manual override button. The inlets incorporate stainless-steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, double outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The products are supplied with metal back nuts. Maximum operating pressure 6 bar. Maximum operating temperature 85°C
Range of wall mounted, three-hole, metal, single outlet (fixed), combination tap assemblies (concealed brass body, various finishes - see model), incorporating quarter turn ceramic disc headwork with single lever, cross top or dome type operating members (see model). The spout outlet incorporates a plastic aerator (F7 & F9 prefix models only). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Concealed, wall mounted, three-hole, single outlet (fixed) combination tap assembly (brass body - various finishes) incorporating quarter turn ceramic disc headwork. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of three-hole, single outlet (swivel) combination tap assembly incorporating brass body - various finishes) and quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of combined bath fillers , waste and overflow assemblies with a brass body (various finishes) incorporating a plastic aerator and a cable operated pop-up waste.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted five-hole, single outlet (swivel), combination tap assemblies (chromium plated brass). Incorporating a self-cancelling diverter to the shower outlet and quarter turn ceramic disc headworks controlling the flow to the spout outlet, with cross top and single lever operating members. The spout outlets incorporate a plastic aerator. The inlet to the shower handsets and the connecting hose body each incorporate an approved check valve cartridge, however, the complete products has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset, and stainless-steel braided silicone lined and PEX lined interconnecting flexible hoses with ½” BSP captive nut end connectors. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of welded stainless steel (S30408 or S31603) pipes. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
‘Blutron’ plastic bodied filter head incorporating EPDM ‘O’-rings for use with filter cartridges (not supplied).For use with LLDPE tube (manufactured to DIN 8072). All models can be specified with or without an integral bracket. Maximum working pressure 6.0 bar. Cold water use only.
Range on inline filter cartridges incorporating plastic bodies. The filter media varies between models and includes active carbon, silver impregnated active carbon, silver carbon block & weak/strong cationic resin. Maximum working pressure 6.0 bar. Cold water use only.
“D” Range of stainless steel (304S31/316S11) press fittings for use with ‘DPX’ series 1 & 2 stainless steel (304S31/316S11) pipe. The fittings and tube are assembled using a crimping tool. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of brass compression fittings for use with copper pipe only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Conex >B< press fittings incorporating copper & brass bodies for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘Trustlene’ range of electrofusion and spigot fittings, with PE100 or brass bodies, for use with SDR11 PE100 pipe (manufactured to IS 4984: 2016). For use above and below ground. Maximum working pressure 16.0 bar. Cold water use only.
Range of copper end feed solder fittings for use with copper tube (EN1057). For above and below ground use. Maximum working pressure for sizes 8mm to 54mm is 25.0 bar. Maximum working pressure for sizes above 54mm is 16.0 bar. Maximum operating temperature 99°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Dual flush WC drop valve with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
Dual flush WC outlet valve with ABS body. The valve incorporates an internal overflow and is operated via a push button assembly for either full or reduced flush. Maximum operating temperature – Cold water use only.
Range of under counter, vented, electric instantaneous (near boiling) water heaters with a stainless steel tank and silicone seals. Maximum operating temperature 98°C.
Range of wall mounted combination boilers providing domestic hot water via a heat exchanger and pressurised central heating system. The products can be supplied with a rigid or flexible filling loop or keyless filling link. The flexible and rigid filling loops incorporate a flexible hose or copper pipe, isolation valve, double check valve assembly (suitable for back flow protection against fluid category 3). The keyless filling link incorporates a CAB backflow prevention device (suitable for back flow protection against fluid category 3). The products also incorporate an expansion vessel and pressure relief valve set at 3.0 bar. Maximum working pressure of primary circuit 2.5 bar. Maximum operating temperature of primary circuit 85°C Maximum working pressure of secondary circuit 8.0 bar Maximum operating temperature of secondary circuit 60°C
DZR brass elbow fitting. Compression connection to be used with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 77 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
