Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an NBR wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
Gate valve with an blue epoxy coated cast iron body, EPDM packing and seal. The valve operates via a hand wheel. Maximum working pressure 16.0 bar. Cold water use only.
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 17.24 bar. Maximum operating temperature 85°C.
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
'FC941'. Black coloured, injection moulded, carbon graphite bearing. For use with water up to 85°C.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add PLUS 2.5'. Grey coloured, site-applied waterproofing admixture. Admixture is to be added to cement mix in a dosing ratio of 2.5 kg per m3 of concrete. Cure for 5°C for 48 hours. For use with water up to 23°C. This material is only approved for the dosing and curing conditions that appear on the approval. If the dosing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BELPA CSA 45'. Beige coloured fibre gasket material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Klingersil® C-4240'. Fibre gasket material, manufactured by calendaring, which is beige coloured on one side and off-white coloured on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'IKV Tribosil MHL 40'. Clear silicone liquid lubricant. Apply as per manufacturer's technical data sheet. No cure required. For use with water up to 85°C.
'Anisotropic Ferrite Special Grade PF-S/3.5/2/4/SM'. Grey coloured, sintered Strontium Ferrite Magnet. For use with water up to 23°C.
'Badadur PBT9 GF10/GK20 TM-Z1 Alpinweiss 230c'. White coloured, injection moulded, glass fibre reinforced PBT material. In January 2024, 'Badadur PBT9 GF10/GK20 alpinweiss 230c' was added to the approval. Both grades are for use with water up to 65°C.
‘Ultrason® E 2010 G4 Uncoloured’. Beige coloured, injection moulded polyethersulphone material. For use with water up to 85°C.
'004DP44 Aiva Composite Saddle'. Blue coloured, injection moulded HDPE fitting. For use with water up to 23°C.
‘Ultrason® P3010 MR White 20264’. White coloured, injection moulded polyphenylsulfone material. For use with water up to 85°C.
'PPHS40'. Pale grey coloured, injection moulded PP material. For use with water up to 23°C.
‘Meti UPVC Fittings’. Grey coloured, injection moulded uPVC fitting. For use with water up to 40°C.
'LSPVC-WE001'. Off-white coloured, injection moulded PVC fitting. For use with water up to 45°C.
'LSPVC-WE001'. Off-white coloured, extruded PVC pipe. For use with water up to 45°C.
`Chemonit 181`. Black coloured, hard rubber material manufactured by roller head extrusion and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.
'EP2/2/4 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 45 IRHD. Tested in-radius size 0.9mm. For use with water up to 85°C.
'TEC N41-70 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'LP4411ANAT, LP37ANAT, LP4611ANAT & LP4811ANAT'. Natural (off-white coloured), compression moulded silicone rubber materials. Shore hardness 40°, 60° and 80° respectively. Tested in-radii sizes between 1.0mm and 2.0mm. For use with water up to 85°C.
'FIX 247 (product code 070323)'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Loctite® AA 326 with Loctite® SF 7649™ Activator'. Loctite® AA 326 is an amber coloured, liquid anaerobic adhesive and Loctite® SF 7649™ is a green coloured, liquid activator. Apply as per manufacturer's Technical Data Sheet dated December 2013. Cure 7 days@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Würth Adhesivo PVC Tixpro'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RIAMAXX HR XE4350 KTW grau R-7040'. Grey coloured, injection moulded, glass filled aliphatic polyketone material. For use with water up to 60°C.
Stop valve with a black plastic body, NBR ‘O’-rings and quarter turn headwork. Maximum working pressure 16.0 bar. Cold water use only.
Range of wall mounted electric showers (various finishes). The GSD/BETTER models incorporate a solenoid valve controlling the flow, which includes a combined plastic and stainless steel strainer and a plastic flow regulator on its inlet. The GSM/DSK/ENTRY models incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated via an infra-red sensor either battery or power supply. The product incorporates a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate an approved single check valve cartridge, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The solenoid is supplied by an isolation valve that incorporates a stainless steel strainer. The spout outlet incorporates a plastic aerator. The product is also supplied with stainless steel braided PEX lined flexible hose assembly for connection to the solenoid valve with ¾” BSP (F) captive nut end connection. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Range of bottom or side entry BS1212-4 (2016) compact type float operated inlet valves for WC flushing cisterns incorporating plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 5.5 litres and a reduced flush of up to 2.7 litres and incorporates a servicing valve and flexible hose on the inlet supply. The cistern is operated by a manually operated push button. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve and a stainless steel braided PEX lined flexible hose assembly. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass or nickel plated DZR brass body. Compression models are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with brass bodies and EDPM ‘O’-rings. All models expect XB-12T incorporate stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model A05406 has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes), ceramic cartridge headwork with a single lever operating member and waterfall spout outlet. The waterfall spout outlets of models A05421, A05422 & A05418 incorporate a stainless-steel mesh. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc headworks with either a single lever, cross top or dome type operating member (see model). The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type with or without a stainless-steel mesh (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a push on/off headwork with rotary temperature control using dome type lever operating member. Both inlets incorporate stainless steel strainers an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Some models are supplied with lever type pop up waste (see model). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 19 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
