Range of spherical valves with a brass body, brass ball, PTFE seats and lever type operating members. Maximum working pressure 40.0 Bar Maximum operating temperature 65.0°C
Range of spherical valves incoporaintg either brass (CP5R models) or nickel plated (CP12 models) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of full port spherical valves with DZR brass bodies, chrome plated or (VIR REDOX) coated brass ball (see model). The products are either lever or handle operated (see model). The 33FFDRE models include a stem extension. Maximum working pressure 32.0 bar. Maximum operating temperature 100°C (wholesome water use), 130°C (closed circuit use only).
Range of gate valves with Red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of combined stop valve and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
Range of manually operated balancing valves with bronze bodies, DZR brass disc and EPDM rubber 'O’-rings. Both models have test points. The F9506 models also have a drain point on the high-pressure test side. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
‘G5 C’ command centre providing chilled (filtered) water via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The inlet to the command centre incorporates two approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum inlet supply pressure 5.0 bar. Cold water use only.
‘G5 CS’ command centre providing chilled or chilled sparkling water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The product incorporates a pressure reducing valve (adjustable outlet pressure between 2.25 and 2.75 bar) on the supply to the carbonator unit. The carbonator inlet incorporates a non-return valve. The product is supplied with a filter cartridge. The inlet to the command centre incorporates two approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum inlet supply pressure 5.0 bar. Cold water use only.
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
‘X086 Ceramic Dome’. Grey coloured, hydraulically pressed ceramic dome component. For use with water up to 23°C.
'Hilox 961'. Brown coloured, dry pressed ceramic material. For use with water up to 85°C.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'Rubalit IS95 White'. White coloured, dry pressed ceramic disc component. For use with water up to 85°C.
'YJ-AL2O3 95%'. White coloured, dry pressed and sintered ceramic disc. For use with water up to 85°C.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431 Primer for use with HYDRALFUN AC BLEU PAM RAL5005-CZL8190 Coating’. Factory applied, dark blue coloured (once applied), powder coating for use with two-part epoxy primer. Mix parts A & B of primer in a 100:10 mass ratio and apply as per manufacturer’s TDS dated February 2024. Cure for 24 hrs at 20°C. Apply coating as per manufacturer’s TDS dated February 2024 and cure for 21 days at 20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PRIMER NATZINC EP9015 SC PART A’ Primer for use with ' HYDRALFUN AC BLEU PAM RAL5005-CZL8190 ' top-coat. Factory applied, blue coloured (once applied) primer and finish-coat. Mix base:hardener of primer in a 100:10 weight ratio and apply as per manufacturer’s TDS February 2024. Then apply top-coat as per manufacturer’s TDS February 2024. Cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Drincable'. Blue coloured, extruded, EPDM rubber electrical cable. Shore hardness 50. Tested in-radius size 0.90mm. For use with water up to 23°C. This approval is for complete cable, the blue coloured outer part being the water contact layer.
‘Drinkflex Aquarius 3G1, 3G1,5, 3G2,5, 3G4, 4G1, 4G1,5, 4G2,5, 4G4 & 4G6’ range of polyolefine cables. The cables have an extruded, blue coloured polyolefine outer (water contact) layer and are available with 3 or 4 internal cores. For use with water up to 23°C.
'Saudi Drip HDPE PE100 pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
'Asrene SP4808'. White coloured, compression moulded HDPE material. For use with water up to 65°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'EPDM-A-001'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 85°C.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
‘Drei Bond 5204’. Yellow coloured anaerobic adhesive paste. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies), incorporating a solenoid valve controlling the flow which is actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The product also incorporates an integral hand dryer. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 43°C
Wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies), incorporating a solenoid valve controlling the flow which is actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The product also incorporates an integral hand dryer. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 43°C
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies with a drain port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (swivel nozzle) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with cross top or lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure - 5 Bar Maximum operating temperature - 60 °C
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Single hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pullout hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and dome type operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure; 5 Bar Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Single-hole, single outlet, (swivel) combination tap assembly, (chrome plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 6 bar Maximum operating temperature 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies with (brass bodies - various finishes), incorporating ceramic cartridge headworks and single lever type operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 65°C
Range of single hole, double outlet (swivel) combination tap assemblies (various finishes) with electronically controlled functions to allow the tap to dispense boiling water, chilled water or sparkling water from under counter units (not supplied or part of this approval) and a ceramic cartridge headwork with single lever operating member controlling the flow of normal mixed water. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5.0 Bar. Maximum operating temperature: 98.0°C.
Range of free standing sanitary macerating disposal units. The flow is controlled by solenoid valve and discharges via type a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Cold water use only.
Bed pan macerator with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 8.0 bar. Cold water use only.
Range of chemical dosing equipment. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Max operating pressure 5.9 bar. Cold water only
Range of cylindrical or tubular expansion vessels with epoxy coated carbon steel bodies. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C
Range of expansion vessels with white epoxy coated steel bodies and butyl diaphragm. Please refer to model for maximum working pressures. Maximum operating temperature 70°C. Maximum working pressure 10.0 bar (all except two models), 8.0 bar (24749 & 24809 only).
Page 11 of 28
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
