Twistloc’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe. Maximum working pressure 12.5 bar. Cold water use only.
‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
‘EPH_WSP19_XXXX’ range of brass end feed and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of urinal autosyphons with plastic body and supplied with plastic backnuts.
Electric instantaneous, vented, mains water heater. Maximum operating temperature 98°C. Cold supply only.
Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.
Range of counter-top or under-sink electrical water heaters. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C, except 65°C for 10L models.
Range of wall hung, gas-fired condensing combination boilers providing domestic hot water via a plate heat exchanger. The pressurised central heating system incorporates an expansion vessel and pressure relief valve set at 3.0 bar. Some models, please refer to model below, incorporate only a primary circuit. Maximum working pressures: Primary circuit: 2.5 bar, Secondary circuit 10.0 bar. Maximum operating temperature both circuits: 60°C.
Range of water meters with brass and plastic bodies and plastic turbines. The inlet incorporates a plastic filter Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of flow meters with plastic bodies. Maximum working pressure 8.0 bar Maximum operating temperature 40°C.
Range of bidet spray kits, wall outlet and brackets with brass bodies (various finishes), bidet spray kits consist of a wall outlet bracket, double interlocking flexible hose and a handset with self-closing trigger mechanism. Maximum working pressure 5 Bar. Maximum operating temperature 60°C.
Range of shower handsets and overhead showers with plastic bodies incorporating EPDM ‘O’-rings and washers. The inlet of the overhead shower models can be supplied with either a washer or a combined washer and stainless-steel strainer. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 980505CPVR | Chrome | 1/2 BSP | bar | 65 °C | Bristan | Shower Rose | No | Not applicable | Not Applicable | Not Applicable |
Range of (chrome plated) plastic shower handsets, each supplied with five (optional) plastic flow regulators (x2 blue, light green, dark green and grey). Maximum operating temperature 60°C.
Range of overhead shower outlets (ABS plastic - various finishes), incorporating a stainless-steel strainer. Open outlet use only Maximum operating temperature 60.0°C.
Range of wall or ceiling mounted shower outlets with chromium plated bodies (or black body for 22123KF0) consisting of showers arms and shower head for installation with specific rough-in sets. Shower head bodies incorporate approved single check valve cartridges, however, the complete assemblies have not been tested to demonstrate it provides backflow protection. The 26.484 model rough-in set incorporates a plastic flow regulator on the inlet. Maximum working pressure: Open Outlet. Maximum operating temperature: 60°C.
Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.
Range of overhead shower outlets with stainless steel bodies (various finishes). The inlet incorporates a stainless-steel filter and a plastic flow regulator. Maximum working temperature 45°C. Open outlet use only.
Range of ‘Y’-pattern strainers with a DZR brass body, stainless-steel strainer and PTFE gasket. Maximum operating pressure 20.0 bar. BS6920 85°C.
Wall mounted hose union taps with brass bodies, incorporating a rising spindle headwork with a ‘T’ type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps ( brass body - various finishes, see), CR20 and CR20/501 incorporate a non-rising spindle headworks with a dome type operating member. GE02 and GE02/201 incorporating quarter turn ceramic discs headworks with a lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted self-closing taps (chromium plated brass) with a dome type operating member. The SCHELL PETIT SC - 02 147 06 99 model incorporates a screwdriver operated servicing valve on the inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Range of stainless steel braided EPDM lined flexible hose assemblies with EPDM seals & EPDM washers, available with a variety of end connections. For use with copper pipe manufactured to EN1057 & HEP20 PB pipe. Maximum working pressure; 6 Bar Maximum operating temperature; 65°c
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313963 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 309644 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| AR3 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| COB SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 COB SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313960 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| CRU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| DEL SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286569 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285401 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286565 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286566 | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 286567 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| HOU SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 285400 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313962 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313965 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BB | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| MOL SHCDIV BLK | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311671 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311672 | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 311673 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| PM2 SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| RP3 PM2 SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 231844 | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| 313961 | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV GM | GUN METAL | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAI SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCVO C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV C | CHROME | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BLK | BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable | |
| SAF SHCDIV BB | BRUSH BLACK | 15mm Compression | 5.0 bar | 85 °C | Bristan | Faceplate | No | 1/4 Turn ceramic disk | Not Applicable | Not Applicable |
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OP TS3650 CL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | |
| OP TS3650 EL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | |
| OP TS3650TO EL C | Chrome | 15mm Compression | 5.0 bar | 65 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable |
Range of concealed, thermostatic blending valves with 2 or 3 shower outlets, incorporating a thermostatic cartridge controlling the temperature that incorporates a manual override button and ceramic disc diverters or quarter turn ceramic disc headworks controlling the flow. The products incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed thermostatic blending valves (brass bodies – various trim sets and finishes) with ceramic diverter controlling the flow which also diverts to 2 or 3 outlets and a thermostatic cartridge controlling the temperature independently. The inlets incorporate an approved check valve cartridge which has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset not supplied. Maximum working pressure 10.0 Bar Maximum operating temperature 60 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 190JK | Chrome | 15mm Compression | 10 bar | 60 °C | Bristan | Handle | No | Single sequential | Not Applicable | Not Applicable | Shower Hose, Handset, Riser Rail, |
Range of wall mounted self-closing thermostatic shower valves with brass bodies, with a chrome plated dome type operating member. Models are also supplied with a chrome plated shower head with a plastic aerator. Both inlets incorporate stainless steel strainers and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted thermostatic blending valves with brass bodies (various finishes). Incorporating either 2-way ceramic disc diverters (2 on, 1 off) that also controls the flow (model DB3100.a.bbb) or with a ceramic disc headwork that controls the flow only to a single outlet (model DB3200.a.bbb.). Both incorporate lever type operating members. The temperature is controlled independently via a thermostatic cartridge with lever type operating members. Inlets incorporate approved check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of normally closed (NC), solenoid valves with plastic bodies and EPDM diaphragm. Models with push-fit connections are for use with copper pipe (manufactured to EN 1057) and PTFE pipe. The products incorporate a plastic or stainless steel filter on the inlet, (except for models with swivel nut, push-fit and nozzle inlets, as well as the 44.007.126 and 01.021.126 models) . The 44.007.126 model incorporates a Y-pattern stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperatures: Cold water use only, 65°C or 90°C for models marked with ℗ - Please consult model section for further details.
Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies and integral stainless steel strainers. 50.005.101 model can also be supplied with an integral plastic strainer. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. 50.009.101 Bistable is for cold water use only.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range lever operated spherical valves with nickel plated brass bodies and chromium plated brass balls. The 1792 model compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of angled spherical valves incorporating a chrome plated brass body and ball with butterfly operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
'NM 96 & NM 99 Ceramic Discs'. Off-white coloured, compression moulded ceramic discs. For use with water up to 85°C.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Grivory HT1VA-5 FWA black 9225'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
Page 80 of 83
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
