'Teadit NA1006'. Green coloured NBR/fibre gasket material manufactured by mixing and calendaring. For use with water up to 65°C.
‘ECOCLEAR White Gray 9098’. Off-white/grey coloured, hot pressed GRP single layered panel. For use with water up to 55°C.
'Crystic VE660'. Olive coloured, contact moulded GRP material. For use with water up to 23°C.
'Everbuild Plumber's P12 Silicone Grease (Barcode: 5055492703842)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'Sanglier SIlicone Spray (1-1)'. Clear (colourless) silicone spray lubricant. Apply as per manufacturer's TDS 'issue 1' dated 28/01/2022. For use with water up to 85°C.
'Carbonfluortec 9720'. White coloured (opaque) lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'SG300'. Clear (colourless) silicone spray lubricant. Apply as per manufacturer's datasheet 'issue 1' dated January 2022. For use with water up to 85°C.
'Grivory HT1V-5 FWA grey L2172.5'. Grey coloured, injection moulded PA6I/6T-GF50 material. For use with water up to 85°C.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Tecacomp PEEK 450 natural (1015088)'. Beige coloured, extruded PEEK material. For use with water up to 85°C.
'Mais' pipe. Black coloured (with blue external stripes), extruded, PE100 HDPE pipe. For use with water up to 65°C.
'Filter 99 3/8 349971 Dark Grey & Filter 99 ½ 349970 Light Grey'. Grey coloured, injection moulded HDPE filters. For use with water up to 23°C.
'ITS PE100 Fittings'. Black coloured, extruded polyethylene fitting. For use with water up to 60°C.
'Trustlene PE-80 Fittings'. Blue coloured, injection moulded, PE80 electrofusion fittings. For use with water up to 23°C.
'Neproplast HDPE PE100 Pipes'. Black coloured, extruded HDPE pipes. For use with water up to 60°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'Sierra PE-100 pipes'. Blue coloured, extruded PE-100 pipes. For use with water up to 65°C.
'Iglidur® UW160 Bearing'. Grey coloured, injection moulded PE bearing. For use with water up to 85°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'LUMILOY GP2300-KA02, GP2200-KA02, GP2200K-KA02, GP2300K-KA02, GP2200-NP, GP2300-NP & GP2300K-NP'. Injection moulded cream, beige, black & brown coloured PPO materials. For use with water up to 85°C.
‘Ramofin PPH300G6BK11’. Black coloured, injection moulded, polypropylene material. For use with water up to 85°C.
'Thermocomp MB006SXP-BK1A994' (black coloured). Injection moulded polypropylene material. For use with water up to 85°C.
'PTFE FE 1000'. White coloured, compression moulded PTFE material. For use with water up to 85°C.
'Duraseal SSAT'. Black coloured, silicone, self-fusing tape. Apply as per manufacturer's instructions 'version 3.2 (EN)' revised 26th August 2022. For use with water up to 65°C.
'TIMO-70 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
'70EP124p'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.
`GCE EP W80`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'70 EPDM 291'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.51mm & 2.50mm. For use with water up to 85°C.
'EPOE7001P-WRC Diaphragm'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'EC-6509-A'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.5mm. For use with water up to 80°C.
'XR0270012'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'RE7012(70SH)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EW Gasket Material'. Black coloured EPDM gasket material which is injection moulded and then spliced (made in Poland). In June 2025, black coloured, compression moulded material (made in China) was added to the approval. Shore hardness 65A. Between November 2022 and February 2023, the in-radius size was 3.9mm. Between March 2023 and November 2029, the in-radius size is 4.4mm. For use with water up to 23°C.
'E65-04BL-G / Black'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 23°C.
'EPDM 1570'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 23°C.
'MRP-EN-50, MRP-EN-55, MRP-EN-60, MRP-EN-65, MRP-EN-70, MRP-EN-75 & MRP-EN-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 80. Tested in-radius size 0.88mm. For use with water up to 65°C.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
‘VF75GRN seals & ‘O’ rings’. Green coloured, injection moulded fluoroelastomer `O` rings & seals. Shore hardness 75. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 5.5mm. For use with water up to 85°C.
'3272 Washers & 'O' rings'. Green coloured, injection moulded FKM washers & 'O' rings. Shore hardness 70. The washers have a tested in-radius size of 0.75mm. The 'O' rings have a tested in-radius size of 1.31mm. For use with water up to 85°C.
'WN1743 BLK O-rings & gaskets'. Black coloured, injection moulded NBR 'O' rings & gaskets. Shore hardness 50. The 'O' rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 0.7mm. For use with water up to 23°C.
'Membrane R219 34 9513 NBR 55 Sh'. Black coloured, injection moulded NBR rubber membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 23°C.
'NB751359C'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'N7018AA'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C. From December 2023, the material is suitable for use with water up to 85°C.
'ME2020/80 Grey'. Grey coloured, injection moulded VMQ sheet material. Shore hardness 80. Tested in-radius 1.0mm. For use with water up to 85°C.
SIL4010, SIL5010 & SIL6010 white translucent. SIL4010, SIL5010, SIL6010 & SIL7010 blue. SIL4010, SIL5010, SIL6010 & SIL7010 red. SIL4010, SIL5010, SIL6010 & SIL7010 yellow. Compression moulded silicone rubber materials. Shore hardness between 40 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'RLC+'. Orange coloured (translucent) anaerobic adhesive. Apply and cure as per manufacturer's Technical Data Sheet, version 1 issued on 03/11/2022. For use with water up to 23°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Tangit ABS'. Grey coloured solvent cement. Apply as per manufacturer's Technical Data Sheet 'Tangit ABS TDS 072017 EN'. Cure for 20 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RTP 0599 X 145641 BLACK'. Dark grey coloured, injection moulded, SAN material. For use with water up to 50°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer and check valve cartridge(s), verified by test (suitable for backflow protection against Fluid Category 2). The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the spout to the solenoid. The spout outlet incorporates a plastic aerator. Maximum working pressure - 10 Bar Maximum operating temperature - 60 °C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 1.0 bar. Maximum operating temperature 65°C
Page 89 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
