Angled servicing valves with chrome plated brass bodies incorporating triangular type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (4.5, 6.0 or 8.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Monobloc manifold containing an in-line pressure reducing valve (Adjustment Range between 2.7 and 3.3 bar, but factory pre-set at 3 bar) and a pre-set expansion relief valve (pre-set pressure 6 bar) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates also a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Inlets and outlets have compression connections, for use with copper pipe to EN1057. Maximum working pressure 12 bar. Maximum operating temperature 80°C.
BT1420-DFM Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of scale inhibitors with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'KEPITAL F25-03 LOF NAT'. Natural (appears white), injection moulded POM material. For use with water up to 60°C.
'RELIBIT 1001 Coating'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's Standard Operating Procedure & Guidelines 'RP/291', '203/2024, Revision 1', dated '1st April 2024'. Cure for 10 hours@35°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sanibiw Dynamic'. Multi-layered, extruded hoses comprising of an off-white, transparent silicone inner layer, white, opaque PES yarn reinforcement layer and black coloured, silicone outer layer. The inner layer has a tested in-radius size of between 0.4mm & 0.8mm. For use with water up to 85°C.
'C100E' & 'C100ELT'. Orange coloured ion exchange resins. For use with water up to 85°C.
‘Silicone Grease A665017, 665016-TUB, A665016, ASG50, AHPSG, PH041, PHCB041/F15220’. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Plustek PB305G33BK37 (black)'. Black coloured, injection moulded, glass reinforced PA material. For use with water up to 85°C.
'PLUSTEK PA100NT-F'. Cream coloured, injection moulded PA66 material. For use with water up to 85°C.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'Viega Raxofix, PE-RT/Al/PE-RT Multilayer Pipe'. Extruded, multi-layered pipe comprising of a black coloured PE-RT inner layer, aluminium middle layer and grey or white coloured PE-RT outer layer. For use with water up to 70°C.
'XRC20B'. Black coloured, injection moulded PE material. For use with water up to 23°C.
'BLAZE PPR01'. Green coloured (with red external stripe), extruded polypropylene pipe. For use with water up to 85°C.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP PURE EPOXY RESIN JF375E'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins, available in light pink or grey colours. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0011’, dated ‘30/01/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 17/0011’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'EPDM 70.54-02 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'M534 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Flexrubber EW70 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'AP-EPDM 50A, AP-EPDM 60A, AP-EPDM 70A & AP-EPDM 80A'. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 80A. Tested in-radius size between 1.15mm & 1.21mm. For use with water up to 65°C.
'EP 70110 HC'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.56mm. For use with water up to 23°C.
'Cura External Leak Sealer (Part No: 27813)'. Clear silicone sealant. Apply as per manufacturer's TDS 'Version 1', dated '16/07/2025'. Cure for 96 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WEICONLOCK AN 301-72 (white coloured) & WEICONLOCK AN 301-48 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'Weld-On 319 PVC Cement'. Clear Solvent Cement. Apply as per manufacturer's TDS '319-05-2024'. Cure for 4 hours@5°C. For use with water up to 23°C.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 5 Bar Maximum operating temperature 65.0°C
Range of bottom entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns with delayed action. . The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of side entry BS1212-4 (2016) delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush and reduced flush. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only. .
Low Level WC suites incorporating a frame mounted ceramic pan that is fitted with a washing & drying arrangement which is fed via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The cistern incorporates a side entry BS1212/4 float operated inlet valve and provides a type `AB` air gap. The drop type flush valve provides a single flush of 6 litres and is operated by elbow push button levers that are designed into the front of the cistern cover. Maximum working pressure 10.0 bar. Cold water use only
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating quarter turn brass headworks, single lever operating members and self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The spout outlet incorporates a plastic flow straightener. The products are supplied with a shower hose, shower handset and brass back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OASISBM | Chrome | 1/2" BSP (F) | 8 bar | 65 °C | Utopia | Body | No | Solenoid | Not Applicable | Aerator |
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TC28 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28, Production date (DD/MM/YYYY) | Body | No | |||||
| TC28-1 | 27.98mm | 10 bar | 85 °C | WANHAI, WRAS, TC28-1, Production date (DD/MM/YYYY) | Body | No |
Single hole, single outlet (swivel) pull down spray combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, various finishes - see model), incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The inlets of the TKUBEDLXX, TKUBESLXX and TQUADDLCM/ models are supplied with a loose ½”x½” BSP (M) chrome plated brass housing. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (stainless steel bodies - various finishes), incorporating a ceramic cartridge headwork controlling the hot and cold with a single lever operating member. The boiling and purified water is controllied via a ceramic disc headwork incorporating a manual override button and a dome type headwork. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway: 98 °C; for other water pathway: 85 °C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| AL 2TH WMBAS C | Chrome | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BLK | Black | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
| AL 2TH WMBAS BB | Brushed Brass | 15mm compression | 5 bar | 65 °C | Bristan | Handle | No | Ceramic cartridge | Not Applicable | Aerator | Flow Regulator Fitted, |
Range of two-hole, single outlet (fixed) combination tap assemblies (brass body – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass body) incorporating a two-way diverter headwork that controls the flow between the spout outlet and shower outlet with dome type operating members. The temperature is controlled independently via a thermostatic mixing cartridge, the incorporates a manual override button. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts, shower hose, handset and flow regulator. Maximum working pressure 5 bar. Maximum operating temperature 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| IRS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
| OPS BSM C | Chrome | 3/4" BSP (M) | 5.0 bar | 60 °C | Bristan | Body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Shower Hose, Handset, |
Two hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The products are supplied with a shower hose and handset and have metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), and incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Maximum temperature 60 degrees Maximum pressure 5 bar.
Range of deck mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), and incorporating a quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. Maximum temperature 60 degrees Maximum pressure 5 bar.
Range of deck mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic aerator, and the product is supplied with shower hose and handset (with flow regulator) and metal backnuts. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Page 226 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
