'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ResiGard APUA (NT) Coating'. Factory applied, grey coloured (once mixed), two-component coating. Mix and apply as per Technical Data Sheet ‘PDS/RG37/Ver15/01/25’. Cure for 1 minute@25°C. For use with water up to 85°C.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hansung M&S GRP Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 60°C.
'UNISILKON TK 002/1000'. Clear lubricant, to be applied as per manufacturer's instructions. For use with water up to 65°C.
'MS Schramberg Sintered Barium Ferrite (10-1176001)'. Dark grey coloured Sintered Barium Ferrite ring component. For use with water up to 85°C.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
'ULTRAMID® A3EG10 FC AQUA BLACK23285'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'ULTRAMID® T7300EG10 FC Aqua BK23285'. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'PLUSTEK PAT302PWG50BK10'. Black coloured, injection moulded, glass-fibre reinforced polyamide material. For use with water up to 85°C.
'Celanex 2002-2FC EF2001 Natural'. Natural (appears white), injection moulded PBT material. For use with water up to 60°C.
'Crastin FGS600F10 NC010 (White)'. White coloured, injection moulded, Polybutylene Terephthalate material. For use with water up 60°C.
'AASTER 962'. Brown coloured (translucent), injection moulded Polyester resin material. For use with water up to 50°C.
'Polimal 122-2 AWTP' (beige coloured) & 'Polimal 1094 AWTP-1' (amber coloured). Contact moulded, unsaturated polyester resin materials. For use with water up to 23°C.
'Sirester EC 0995/AT'. Pale orange coloured, unsaturated polyester resin material manufactured by filament winding. For use with water up to 23°C.
'Omanplast HDPE Pipe'. Black coloured (with blue external stripes), extruded HDPE pipe (manufactured in Muna Noor Manufacturing & Trading LLC, Sohar & Muna Noor Manufacturing & Trading LLC, Rusayl, Oman). For use with water up to 60°C.
'Ori-Plast Electro-Fusion Fittings'. Black coloured, injection moulded PE 100 Electro-Fusion Fittings. For use with water up to 65°C.
'AMIANTIT HDPE Pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 50°C. Please note that only pipes marked with 'HE3490' are covered by the scope of the approval.
'NORYL WM330G-73701 (black), NORYL WM330G 7G8B4911 (grey) & NORYL WM330G-4G8B5291 (beige)'. Injection moulded PPE-PS materials. For use with water up to 85°C.
‘NORYL’ black coloured, grey coloured or beige coloured, injection moulded PPE + PS materials. FE1410PW – 73701. FE1520PW – 73701. FE1630PW – 73701. FE1740PW – 73701. FE1520PW - 4G8B5291. FE1630PW - 4G8B5291. FE1410PW – 7G8B4911. FE1520PW – 7G8B4911. FE1630PW – 7G8B4911. FE1410PW-4G8B5291, FE1740PW-4G8B5291 & FE1740PW-7G8B4911 were added to the approval in April 2025. For use with water up to 85°C
'TERRATHERM Fittings'. Green coloured, injection moulded PP-R fittings. For use with water up to 70°C.
'UPS SEAL-FLEX TAPE'. Extruded, self-fusing silicone rubber tapes available in Black and Red colours. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'GW 160m'. White coloured (opaque), thread sealant. For use with water up to 85°C.
'F802'. White coloured, extruded PTFE material. For use with water to to 85°C.
'EP50/1 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 50. Tested in-radius 1.7mm. For use with water up to 85°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'EP60/1 BLK'. Black coloured, compression moulded EPDM diaphragm seal. Shore hardness 60. Tested in-radius size 0.75mm. For use with water up to 85°C.
'558CM'. Black coloured, transfer moulded EPDM O-Ring. Shore hardness 60. Tested in-radius size 0.87mm. For use with water up to 85°C.
'CSTD/BS6920-BA60' (shore hardness 60), 'CSTD/BS6920-BA70' (shore hardness 70) and 'CSTD/BS6920-BA75' (shore hardness 75). Black coloured, compression moulded EPDM materials. Tested in-radius size 1.05mm. For use with water up to 85°C.
'Precision782628 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'N146 Sealing Cap and Bellow'. Black coloured, injection moulded nitrile rubber sealing cap & bellow. Shore hardness 70. The cap has a tested in-radius size of 0.6mm and the bellow has a tested in-radius size of 1.0mm. For use with water up to 23°C.
'N8018AA'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'01/N50 VMQ, 01/N60 VMQ & 01/N70 VMQ White. 01/M50 VMQ, 01/M60 VMQ & 01/M70 VMQ Red. 01/L50 VMQ, 01/L60 VMQ & 01/L70 VMQ Blue'. Range of injection moulded silicone rubber `O` rings and gaskets available in white, red & blue colours. Shore hardness between 50 & 70. Tested in-radii size of between 1.0mm and 2.0mm. For use with water up to 85°C.
'ULTEM™ PW1010-1000'. Amber coloured, injection moulded PEI (polyetherimide) material. For use with water up to 85°C.
Range of stop valves with plastic bodies. The valves incorporate a built in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with model SVSM66MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only
Bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum operating pressure 10 bar. Maximum operating temperature 40°C.
'XRRA 410B GR1500'. Grey coloured, injection moulded U-PVC material. For use with water up to 23°C.
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) electronically controlled tap assembly. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator, and products are supplied with interconnecting stainless steel braided silicone lined flexible hose assemblies. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Page 208 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
