SAN MARCO RUBINETTERIA S.r.l. Approvals


#2004326

Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks with single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2004326
Expiry date:
30/04/2025
Size:
Stainless steel braided PEX lined flexible hose assemblies incorporating ½” captive nut end connections.
Marking:
SMR Logo on rear of operating member.
Installation Requirements:
R001 R006 R009 R010
Model:
HILTON
Approval Holder:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval


#2004325

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The inlets incorporate a combined TPE washer and stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2004325
Expiry date:
30/04/2025
Size:
Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections.
Marking:
SMR Logo on rear of body
Installation Requirements:
R001 R006 R010
Model:
AD4
Approval Holder:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval


#2007346

Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2007346
Expiry date:
31/07/2025
Size:
Stainless steel braided EPDM lined hose assemblies incorporating ½” captive nut end connections.
Marking:
SMR logo on rear of body
Installation Requirements:
R001 R006 R010
Model:
TM1
Approval Holder:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval


#2010360

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2010360
Expiry date:
31/10/2025
Size:
Stainless steel braided EPDM lined hose assembly incorporating ½” (M) end connection.
Marking:
SMR on operating member.
Installation Requirements:
R001 R006 R010
Model:
Cubic Quadrant Single Lever New Media ACT2087
Approval Holder:
Norcros Group (Holdings) Limited T/A Abode
Company Name
Norcros Group (Holdings) Limited T/A Abode
Address
Unit L Zenith Park Whailey Road Barnsley
Postcode
S75 1HT
Phone
01226 283434
General Email
mstaweczny@abodedesigns.co.uk

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)
General Email

View All Listings by this Company

Print This Approval


#2109330

Range of single hole, single outlet (swivel) combination tap assemblies with (chrome plated) brass bodies. Incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a aerator. Inlets incorporate single check valve cartridge (however the the complete assembly has not been tested to demonstrate it provides adequate backflow protection)Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2109330
Expiry date:
30/09/2026
Size:
Stainless steel braided EPDM lined hose assembly incorporating ½” BSP (M) end connections.
Marking:
SMR on operating member.
Installation Requirements:
R001 R006 R010
Model:
HYDRUS, MODENA, CLYNE, AQUAREACH, 840MINIMALIST TOP LEVER
Approval Holder:
Norcros Group (Holdings) Limited T/A Abode
Company Name
Norcros Group (Holdings) Limited T/A Abode
Address
Unit L Zenith Park Whailey Road Barnsley
Postcode
S75 1HT
Phone
01226 283434
General Email
mstaweczny@abodedesigns.co.uk

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)
General Email

View All Listings by this Company

Print This Approval


#2110356

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The cold inlet hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2110356
Expiry date:
31/10/2026
Size:
Stainless steel braided EPDM lined flexible hose assemblies with ½” BSP captive nut end connections (hot), ½” BSP (M) (cold).
Marking:
SMR on operating member
Installation Requirements:
R001 R006 R010
Model:
BT1 & BQ1
Approval Holder:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval


#2110357

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic disc headworks with a single lever operating members. The spout outlet incorporates a plastic flow straightener or aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2110357
Expiry date:
31/10/2026
Size:
Stainless steel braided EPDM lined flexible hose with ½” BSP captive nut end connections.
Marking:
SMR on body
Installation Requirements:
R001 R006 R010
Model:
KG1 & KM1
Approval Holder:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval


#2110387

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator. The cold inlet hose incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2110387
Expiry date:
31/10/2026
Size:
Stainless steel braided EPDM lined flexible hose assemblies with ½” BSP captive nut end connections (hot), ½” BSP (M) (cold).
Marking:
SMR on operating member
Installation Requirements:
R001 R006 R010
Model:
QUANTIC COMBINATION TAP ASSEMBLIES
Approval Holder:
Norcros Group (Holdings) Limited T/A Abode
Company Name
Norcros Group (Holdings) Limited T/A Abode
Address
Unit L Zenith Park Whailey Road Barnsley
Postcode
S75 1HT
Phone
01226 283434
General Email
mstaweczny@abodedesigns.co.uk

View All Listings by this Company

Print This Approval


#2201301

Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating ceramic cartridge headworks with single leaver operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2201301
Expiry date:
31/01/2027
Size:
Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections.
Marking:
SMR on operation member
Installation Requirements:
R001 R006 R010
Model:
Capris Swan Capris Quad Models added April 2022 FORTE TWIST ACB // FORTE TWIST Hose bore = DN10. End connection = 15mm pushfit. SUPER TWIST ACB // SUPER TWIST Hose bore = DN13. End connection = 22mm pushfit.
Approval Holder:
Norcros Group (Holdings) Limited T/A Abode
Company Name
Norcros Group (Holdings) Limited T/A Abode
Address
Unit L Zenith Park Whailey Road Barnsley
Postcode
S75 1HT
Phone
01226 283434
General Email
mstaweczny@abodedesigns.co.uk

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)
General Email

View All Listings by this Company

Print This Approval


#2201346

Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chrome plated), incorporating ceramic cartridge headworks with single leaver operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2201346
Expiry date:
31/01/2027
Size:
Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut end connections.
Marking:
SMR on operation member
Installation Requirements:
R001 R006 R010
Model:
BREGGIA SWAN & BREGGIA RIGHT ANGLED COMBINATION TAP ASSEMBLIES
Approval Holder:
Howdens Joinery
Company Name
Howdens Joinery
Address
Thorpe Road Howden East Yorkshire

View All Listings by this Company
Manufacturer:
SAN MARCO RUBINETTERIA S.r.l.
Company Name
SAN MARCO RUBINETTERIA S.r.l.
Address
Via Carducci 10 13867 Pray (BI)

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 1 of 2

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.