Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10130420) Maximum working pressure 25.0 bar (model 10130379) Maximum working pressure 40.0 bar (models 10130277 & 10130345) Maximum operating temperature 85°C.
Range of spherical valves incorporating either brass (870228 &961665) or nickel plated (961159, 961708, 837973, 845188 & 845187) brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with DZR brass bodies, chrome plated balls, PTFE seats and FKM O-rings. Maximum working pressure 30.0 bar. Maximum operating temperature 85°C.
Range of spherical valves (brass or chrome plated brass bodies), incorporating chrome plated brass ball and either a single lever or T type operating member. Maximum working pressure 25.0 or 50.0 Bar (see models) Maximum operating temperature 20.0°C
Range of brass stopcocks. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘BOSS VENTURI’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of balancing valves with DZR brass bodies with two test ports, incorporating a non-rising spindle headwork. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'Sylglas Plumber Fix Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E70C397'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size between 0.25mm and 5.0mm. For use with water up to 85°C.
'VULCAN VEE4 Bellow & Boot'. Black coloured, compression moulded EPDM bellows and boot components. Shore hardness 70. The bellows has an in-radius size of 3.0mm and the boot has an in-radius size of 0.9mm. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'RBL-9200-20, RBL-9200-30, RBL-9200-40, RBL-9200-50, RBL-9200-60, RBL-9200-65 & RBL-9200-70'. Transparent, colourless injection moulded silicone rubber materials. Shore hardness between 20 & 70. Tested in-radii size between 0.75mm & 2.89mm. For use with water up to 85°C.
'RIAMAXX HR XE4349 KTW natur. RIAMAXX HR XE4349 KTW schwarz. RIAMAXX HR XE4350 KTW natur. RIAMAXX HR XE4350 KTW schwarz. RIAMAXX HR XE4351 KTW natur. RIAMAXX HR XE4351 KTW schwarz. RIAMAXX HR XE4352 KTW natur. RIAMAXX HR XE4352 KTW schwarz'. Natural (appears beige) and black coloured, injection moulded Polyketone materials. For use with water up to 85°C.
‘THERMOLAST DW Compound series (DW/CS2)’. Natural (appears white), injection moulded TPE-S materials. The materials can be coloured and include the following grades: DW(1)OCX-(2): (1) – for "0" to "8" indicating hardness: DW5OCX-(2) (55 ShA). DW6OCX-(2) (65 ShA). DW7OCX-(2) (75 ShA). DW8OCX-(2) (85 ShA). DW0OCX-(2) (35 ShD). (2) - Extension of 4 digits indicating colour. The four digits stands for this: LCNT -> natural material without colour. All other numbers depends on colour. The first digit of the 4 digit colour code indicates the ground colour: 1 = yellow, 2 = orange, 3 = red, 4 = violet, 5 = blue, 6 = green, 7 = grey, 8 = brown & 9 = white or black. The other digits of the 4 digit colour code, indicates the particular shade. For use with water up to 85°C.
‘Wall mounted, electronically operated tap assemblies (brass bodies - in various finishes). The flow is controlled by a solenoid valve that is actuated via an infra-red sensor on the spout. The spout outlet incorporates plastic aerators. Maximum working pressure 6 bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve that is activated via an infrared sensor. The spout outlet incorporates an aerator. Maximum working pressure: 8.0 Bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure - 8 Bar. Maximum operating temperature - 65 °C.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of quarter turn ceramic disc or non-rising spindle headworks (see models) with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone rubber gaskets for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 90.0°C
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Thermostatic cartridges with a plastic body and stainless-steel strainer mesh. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-out spray type. Maximum working pressure 10.0 Bar. Maximum operating temperature 65.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a pull-down spray with a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever (Elysian models) or dome type (Milani models) operating member. The spout outlet incorporates a plastic flow straightener (Elysian models) or a plastic aerator (Milani models). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a single sequential cartridge that controls both the flow and temperature with a single lever operating member. The spout outlets incorporate a plastic flow straightener. All products are supplied with a plastic strainer and a spherical valve,brass adaptor, plastic flow regulator and brass flow regulator holder for installation on each inlet tail. The models ending in 610/610L are supplied with copper tails. All other models are supplied with stainless steel braided PEX lined flexible hose assemblies with ⅜” captive nut end connections and an additional fibre washer. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, swivel, combination tap assemblies in various finishes. The models incorporate a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet, (fixed), combination tap assemblies, (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum operating pressure 10 bar. Maximum operating temperature 60°C 13 623 180 rough-in set does not form as part of this approval.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated or matt black finished brass), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets of models 62315-5001, 62901-5001, 62907-5001 incorporate a plastic flow straightener. The inlet of model 62913-5001 incorporates a plastic flow restrictor. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, two hole, single outlet fixed combination tap assemblies (chromium plated brass), incorporating a single sequential thermostatic cartridge controlling both flow and temperature with a single lever operating member. The spout outlets incorporate a plastic flow straightener The inlets incorporate a concentric isolation valve, stainless steel strainer and a plastic flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two hole, single outlet fixed combination tap assembly (chromium plated brass), incorporating a single sequential thermostatic cartridge controlling both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate a stainless steel strainer and a plastic flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 65°C
Range of Wall mounted, four-hole, single outlet (swivel) combination tap assemblies (Various Finishes). Incorporating a ceramic cartridge headwork controlling the flow to the shower handset and two quarter turn ceramic disc headworks controlling the flow to the spout outlet, all with single lever operating members. The spout outlets incorporate a plastic aerator. The inlet to the shower handsets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted or floor standing spout outlets (fixed or swivel - see model in various finishes). All models incorporate a plastic flow straightener, except for the 93-Floor Mounted Bath Filler which has a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted spout outlets (fixed or swivel - see model, Various finishes) incorporating a plastic flow straightener. The products are supplied with metal backnuts.
Non-metallic materials and components comply with BS6920 at 60°C
Range of chemical dosing equipment. The outlet of the injector incorporates a connection for injection of chemicals via venturi action. Max operating pressure 5.9 bar. Cold water only
Range of PFD press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Flowtech range of green butt welded polypropylene fittings for use with Flowtech’ PPRGF or PPR pipes. Maximum working pressure 20.0 bar. Cold water use only.
Range of fohn stainless steel (SUS304/316L) crimp fittings incorporating EPDM ‘O’-rings. For use with FOHN stainless steel pipes (SUS304/316L). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 63 of 82
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
