‘Rada’ electronically controlled thermostatic blending valve, with a stainless-steel body, EPDM ‘o’ rings and seals. Maximum working pressure; 13.8 Bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic shower valves, (brass bodies - various finishes) incorporating two push button headworks controlling the flow to the hand shower or overhead shower outlet. The temperature is controlled independently via a thermostatic cartridge with single lever operating member which incorporates a manual override button. The inlets incorporate stainless steel strainers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of wall mounted, concealed, thermostatic shower valves (brass bodied - chrome plated trim set), flow is controlled via a solenoid valve that is activated by an infrared sensor or touch sensor. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainers and approved single check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of wall mounted, concealed, thermostatic shower blending valves with brass bodies and polished stainless-steel trim/faceplates. Flow is controlled by a single sequential headwork with a single lever operating member. The inlets of the H96BOX each incorporates a isolation valve and a plastic strainer. The 9639SRV and 9632SRV models incorporate a plastic strainer and a plastic flow regulator on each inlet. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Wall mounted, exposed, thermostatic bar type shower mixing valve (brass body, various finishes - see model). The product incorporates a 2-way ceramic disc diverter headwork with a single lever operating member controlling the flow to either shower outlet. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member and a manual override button. The product is supplied with a shower riser, overhead shower, shower hose and shower handset. The inlets incorporate a combined washer and stainless-steel strainer, as well as an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted thermostatic blending valves, (brass bodies – chrome plated plastic trim sets) incorporating single sequential headworks controlling both flow and temperature. The inlets incorporate approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate back flow protection. Model (31997W is valve only) all other models are supplied with shower hose, handset & riser rail assembly. Maximum operating pressure 5 bar. Maximum operating temperature 50°C
ange of wall mounted thermostatic shower valves, (brass bodies – chrome plated plastic trim sets). Incorporating a sequential headwork controlling flow and temperature. Model (31983W-CP) direction of flow is controlled independently with a single lever operating member that diverters from shower to shower. Model (31982W-CP) is supplied with a shower hose, handset & riser rail assembly. Model (31983W-CP) is supplied with a shower hose, handset, over head shower & riser rail assembly. Maximum operating pressure 5 bar. Maximum operating temperature 50°C
Range of pilot operated pressure reducing valves with epoxy coated ductile iron body (either blue or red/brown). The valve has an adjustable pressure reducing facility controlled via a pilot valve, with auxiliary components including stainless steel tubing and fittings, nickel plated brass spherical valves and a ‘Y’-pattern strainer. DN600-DN1400 sizes also incorporate a needle valve and a swing gate valve. Maximum inlet supply pressure 16.0 bar. Outlet pressure setting is adjustable in the range of 1.0 – 7.2 bar. Maximum operating temperature 65°C.
Range of in-line lever operated spherical valves with stainless steel bodies, stainless steel ball and PTFE seats. Maximum working pressure 30 Bar. Maximum operating temperature 85 °C.
Range of lever, handle or square operated (see models) spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of spherical valves incorporating nickel plated (brass bodies with chrome plated brass ball and operated via lever, handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly operated spherical valves with brass or nickel-plated brass or DZR brass bodies models Models M69150000LPDZR & M69220000FBDZR . Incorporating brass or nickel-plated brass or DZR brass ball. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C
Range of inline or angled servicing valves incorporating a white (-W and -01 suffix models) or grey (all other models) plastic body, chrome plated brass ball, EPDM washers and EPDM ‘O’-rings. The products are either lever operated (-H and -01 suffix models) or screwdriver operated (all other models). Push fit connections are for use with copper pipe (manufactured to EN 1057), John Guest BPEX pipe or PEX barrier pipe (manufactured to BS EN 7291-3) and John Guest BPB or polybutylene barrier pipe (manufactured to BS EN 7291-2). Maximum working pressure and operating temperature: 13.24 bar @ 20°C, 6.0 bar @ 65°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of angled valves with brass bodies (some models chrome plated). Maximum working pressure 10 bar. Maximum operating temperature 65°C
‘Satefy group’ with a brass inlet and a DZR brass body which incorporates a lever operated spherical valve, followed by an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) and a plastic bodied pressure relief valve (set at 6.0 bar). The product incorporates a test point. The compression connections are for use copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Ballorex’ range of regulating valves with DZR brass bodies, PTFE seats, EPDM ‘O’-rings and washer. The product incorporates two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
UV disinfection unit with stainless steel body. Maximum working pressure 9.0 bar. Maximum operating temperature 55°C.
'(POM) MC90'. White coloured, injection moulded POM material. For use with water up to 85°C.
'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'KH659R'. Black coloured, compression moulded, resin impregnated carbon ring. For use with water up to 85°C.
'KH659AC'. Black coloured, compression moulded, resin impregnated carbon ring. For use with water up to 85°C.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'557WE, 557WG & 557WM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60, 70 & 90. Tested in-radius size 0.85mm. For use with water up to 85°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'6741'. Brown coloured, compression moulded FKM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 85°C.
'RIAMAXX HR XE4349 KTW natur. RIAMAXX HR XE4349 KTW schwarz. RIAMAXX HR XE4350 KTW natur. RIAMAXX HR XE4350 KTW schwarz. RIAMAXX HR XE4351 KTW natur. RIAMAXX HR XE4351 KTW schwarz. RIAMAXX HR XE4352 KTW natur. RIAMAXX HR XE4352 KTW schwarz'. Natural (appears beige) and black coloured, injection moulded Polyketone materials. For use with water up to 85°C.
Wall mounted electric heater, incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of single-hole, single outlet (fixed) electronically operated, tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by a touch sensor. The spout outlets incorporate plastic aerators. Max working pressure 8.0 bar. Max operating temperature 65°C.
Range of spring loaded resilient trim check valve cartridges with plastic bodies, stainless steel spring and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 16 Bar Maximum operating temperature 65°C (model OV15/DN15-EPDM 31.0001.0 only) Maximum operating temperature 85°C for all other models
Range of aerators with plastic bodies and EPDM ‘O’-rings. Open outlet use only. Maximum operating temperature 65ºC.
Range of quarter turn ceramic disc or non-rising spindle headworks (see models) with brass bodies and EPDM `O` rings for insertion into specifically dimensioned bores. Maximum working pressure; 10 Bar Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and silicone rubber gaskets for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 90.0°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridges and quarter turn ceramic discs headworks with single lever or dome type operating members. The spout outlets are either open outlet, waterfall or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating single sequential headworks controlling both flow and temperature with a single lever type operating member. Model A6697AA is supplied with a combined strainer, servicing valve that incorporates a single approved check valve cartridge verified by test, suitable for backflow protection to fluid category 2. Maximum working pressure; 10 Bar. Maximum operating temperature 65°C.
Range of single outlet fixed combination tap assemblies (chromium plated brass), incorporating a single sequential thermostatic cartridge controlling both flow and temperature with a single lever operating member. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with a combined strainer, servicing valve that incorporates a single approved check valve cartridge verified by test, suitable for backflow protection to fluid category 2. Maximum working pressure 10 Bar Maximum operating temperature 65°C
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic aerator and some of the models are supplied with lever type pop-up wastes.
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate plastic aerators, flow straighteners, stainless steel strainers or open outlet type spouts (see models). Some models are supplied with a click type pop-up wastes, that have been verified by test (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc or ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and is also supplied with an optional plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), with non-rising spindle headwork and single lever operating members.The spout outlet incorporates a plastic aerator. Maximum working pressure 5.5 bar. Maximum operating temperature 60°C
Page 58 of 86
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
