Range of Conex >B< press fittings incorporating copper & brass bodies for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of copper end feed solder fittings for use with copper tube (EN1057). For above and below ground use. Maximum working pressure for sizes 8mm to 54mm is 25.0 bar. Maximum working pressure for sizes above 54mm is 16.0 bar. Maximum operating temperature 99°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single and dual flush WC outlet valves. The valves incorporate an internal overflow and are operated with one push button (single flush) or two push buttons (dual flush). Cold water use only.
Dual flush WC drop valve with an internal overflow. The valve is operated via a push button assembly for either full or reduced flush. Cold water use only.
‘G5 BC’ range of command centres that provide instant near boiling and chilled water (both filtered) via an electronically controlled tap (not supplied). Flow is controlled via a combination of solenoid valves and electronic pumps to the outlets. The products are supplied with a filter cartridge. The products can also be supplied with a hot water booster and/or a venturi system to provide mains cold water combined with water from the hot water tank (see model). Maximum working pressure 5.0 bar. Maximum operating temperature 100˚C. Cold supply only.
DZR brass elbow fitting. Compression connection to be used with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of shower outlets (brass or stainless-steel bodies – various finishes) incorporating EPDM O-rings. Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower heads with chromium plated ABS bodies. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 75°C
Wall mounted and ceiling mounted shower arms (chromium plated brass).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets, (plastic bodies – various finishes) incorporating a plastic flow regulator in the inlets.
Non-metallic materials and components comply with BS6920 at 65°C
Range of multi-function overhead shower outlets, (plastic bodies – various finishes). The inlets incorporate plastic flow restrictors and stainless-steel strainer washers.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall and ceiling mounted shower arms with (brass bodies - various styles and finishes). Maximum operating temperature 60°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted shower outlets (various finishes). The inlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C. Open outlet use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of vertical cased and insulated direct and indirect unvented stainless steel hot water storage cylinders. Fitted with a Caleffi 309463 GLD temperature and pressure relief valve sat at 6 bar & 90°C, and supplied with an inlet control group consisting of in-line pressure reducing valve (Caleffi set at 3 bar) and pressure relief valve (Caleffi CWIC200055) set at 4.5 bar, and incorporates a stainless-steel mesh and an approved check valve cartridge (verified by test suitable for backflow protection against Fluid Category 2), expansion vessel and filling loop. Maximum working pressure 4.4 bar. Maximum operating temperature 99°C.
Range of deck mounted, manual blending valves, incorporating a ceramic cartridge headworks with a single lever operating member. The product is supplied with a stainless-steel braided, PEX lined flexible connection hose assembly that incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted bar type thermostatic shower mixer (brass body – various finishes) incorporating a half turn ceramic disc headwork controlling the flow with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member incorporating a manual override button. Both inlets incorporate a check valve cartridge, that has not been fully tested to demonstrate it provides adequate backflow protection and stainless-steel strainers. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of T-type thermostatic mixing valves (chrome plated DZR brass). The 521928 model incorporates stainless steel strainers in the inlets and approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure: 10.0 Bar. Temperature: 90°C
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of T-type thermostatic blending valves with chromium plated brass bodies. Temperature is controlled via a thermostatic cartridge. The inlets of all models except model 521308, 521324, 521314 and 521318 incorporate single check valve cartridges (verified by test - suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. Compression fitting connection to be used with copper pipe EN1057 only. Maximum working pressure 10 bar. Maximum operating temperature 85°C except for models CA-100827 & CA-100828 both 60°C
Range of concealed thermostatic valves with thermostatic cartridges. Models SHO001PL, SHO032VI, SHO042KL, SHO141OT, SHO020LO，SHO026PR， SHO009EL，SHO045NR, SHO047NS, SHO000PL，SHO041KL & SHO025PU consist of quarter turn ceramic disc headworks controlling the flow and the temperature is controlled independently via thermostatic cartridge. Models SHO010EL SHO002PL,SHO033VI, SHO043KL SHO142OT， SHO021LO, SHO027PR, SHO046NR & SHO049NS consists of a two-way diverter cartridge controlling the flow and a thermostatic cartridge controlling the temperature. Model SHO012PR consists of a three-way diverter cartridge controlling the direction of flow, a thermostatic cartridge controlling the temperature and a quarter turn ceramic disc controlling the flow. All models incorporate cube, dome, cross-top or single lever type operating members. The inlets incorporate stainless steel strainers and single check valve cartridges; however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and discs and EPDM rubber seat. Maximum working pressure 16.0 bar. Cold water use only. Maximum operating temperature 85°C (from Sept 2021)
Range of handwheel & gear operated butterfly valves with blue epoxy coated ductile iron bodies and discs and EPDM rubber seat. Maximum working pressure 16.0 bar. Cold water use only. Maximum operating temperature 85°C (from Sept 2021)
Range of concealed two way & three way ceramic disc diverters, (brass bodies – various trim sets and operating members). Maximum working pressure: 10.0 Bar
Range of solenoid valves with a brass body and an EPDM diaphragm and gasket. For use with copper pipe (manufacture to EN1057). Maximum working pressures: X210525720001aa, X210525720002aa, X210525720101aa and X210525720102aa models 10.0 bar. X210525720011aa and X2105257201111aa models: 3.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of inline spherical valves, (nickel plated brass bodies), chrome plated brass balls, PTFE seats and washers with lock-shield, single lever or T-type operating members. Maximum working pressure: ¼” to 1” = 40.0 bar, 1¼” to 2” = 32.0 bar, 2½” to 3” = 25.0 bar, 4” = 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical (HCVB) or isolation (HBVU) valves with plastic bodies incorporating EPDM ‘O’-rings and seals. HBVU metric (mm) models are available in black or white, HBVU imperial (”) models are available in white or grey, HCVB models are available in black only. HBVU models are lever operated, HCVB models are screwdriver operated. HBVU models are for use with LLDPE pipe (manufactured to DIN 8072). The HCVB 15mm model push fit connection is for use with PEX-b pipe (manufactured to EN ISO 21003 B1) and the HCVB 22mm models push fit connection is for use with PEX pipe (manufactured to BS7291-3). Maximum working pressures: HBVU models: 10.0 bar. HCVB models: 7.0 bar (HCVB models push fit connection), barbed (spigot) connections of HCVB models are open outlet use only. Cold water use only.
Range of brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of stop valves withbreonze, brass or chrome plated brass bodies, EPDM and PTFE washers incorporating a T type or lockshield operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating pressure 85°C
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epoxy PB Pipe Green (W) & Epoxy FB Pipe Green (HW)'. Factory applied, green coloured epoxy powder coatings. The substrate to which the coating is to be applied is pre-heated to 220˚C for 15 minutes before applying the coating as per product data sheet dated '27th June 2023'. Post-cure for 15 minutes@215°C. For use with water up to 85°C. This material is only approved for the pre-heat and post-cure conditions that appear on the approval. If the pre-heat and/or post-cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'HKUST002'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions 'HKUST002101001', '01', dated '03/11/2020'. Cure for 168 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Primer coating Spu‐221(A) & Spu‐221(B)’ for use with ‘Top coating: Spu‐222(A) & Spu‐222(B)’. Factory applied, grey coloured (once mixed) Acrylic Polyurethane primer & coating. Mix parts A and B of the primer in a 4:1 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. Mix parts A and B of the topcoat in a 4:2 volume ratio and apply as per manufacturer’s instructions dated 5th May 2018. Cure for 48 hours@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FIBER TECH 82’. Factory applied, natural (appears dark yellow) fibreglass resin. Spray apply as per manufacturer’s Method Statement Ref ‘PP-GRP-092021-R1’, dated ‘21 Sept 2020’. Cure for 72 hours@25°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Nitocote EP405 (3821)’. Site applied, blue coloured, two component solvent free epoxy resin coating consisting of two bases (coat 1 base; Nitocote EP405 white & coat 2 base; Nitocote EP405 blue) & clear EP405 hardener. Mix parts A & B of each coat in a 100:13 weight ratio and apply in accordance with Fosroc data sheet issue 7 (CI/SfB: Pn6) dated November 2013. Cure coat 1 for 18 hours@7°C. Cure coat 2 for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Renderoc Plug 20'. Site applied, dark grey coloured, cementitious repair mortar. Mix with water in a 3:1 volume ratio and apply as per manufacturer's datasheet '14' dated 'June 2018'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusamatic Electrofusion Fittings'. Black coloured, injection moulded, polyethylene Electrofusion Fittings (made in UK from Ineos Eltex TUB121 & Hostalen CRP 100 Resist CR Black). In December 2023, Electrofusion Fittings made in Anhui Province China from Borouge Borsafe HE3490-LS & Hostalen CRP 100 Resist CR black were added to the approval. For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'Fusamatic Electrofusion and Spigot Fittings'. Black coloured, injection moulded, polyethylene Electrofusion and Spigot Fittings (made from Ineos Eltex TUB121, Hostalen CRP 100 Resist CR Black & Borouge Borsafe HE3490-LS). For use with water up to 60°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'Tefzel® ETFE 200, 207, 280, 750, HT2181, HT2183 & HT2185'. Un-pigmented (white coloured), compression moulded ETFE material. For use with water up to 85°C.
‘Sikadur 31 DW Rapid for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW Rapid’ in a 3:1 weight ratio and apply as per product data sheet ‘March 2021, Version 01.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur 31 DW for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW’ in a 3:1 weight ratio and apply as per product data sheet ‘February 2022, Version 03.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 56 of 71
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
