‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.

Section:

5311 Resin Anchors

Expiry date:

31/08/2030

Approval Holder:

Sika Services AG

Company Name

Sika Services AG

Address

Tueffenwies 16, CH-8048 Zuerich

Country

Switzerland

Phone

+41 58 436 40 40

General Email

sika@sika.ch

View All Listings by this Company

Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.

Section:

2075 Float Operated Inlet Valve

Section Subtitle:

Can be used to achieve a recognised air gap arrangement, providing it meets the appropriate backflow requirements. Suitable for use in a WC suite, provided it forms an arrangement which meets the requirements of Type AUK1 air gap and an appropriate WC performance specification.

WRAS Approval Number:

251102048

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Model M3230WR can be supplied with either a brass or plastic ½” connection, a plastic 3/8” connection and either delayed or non-delayed action type float valve.

Size:

3/8” BSP (M) 1/2” BSP (M) (brass or plastic inlet connection)

Marking:

Miellat, Model number & BS1212-4 on body.

Installation Requirements:

R001 R550

Expiry date:

30/11/2030

Model:

M3230WR

Approval Holder:

Miellat Industries LLC

Company Name

Miellat Industries LLC

Address

Unit B-24, KEZAD Logistics Park, 2 Al Zaeem St, Khalifa Industrial Zone Abu Dhabi

Country

U.A.E

General Email

info@miellat.com

View All Listings by this Company

Section:

0531 Combination Tap Assemblies

Description:

A Two hole tap(s) with a single outlet and a fixed spout, incorporating a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)

Deck mounted. Capable of achieving AUK2 Tap gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005 R030

Expiry date:

31/01/2031

Model:

604587 X XXX

Notes & Further Information

X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1

Approval Holder:

Travis Perkins PLC

Company Name

Travis Perkins PLC

Address

Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

Section:

0531 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and a fixed spout, incorporating a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)

Deck Mounted Capable of achieving AUK2 tap gap.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005 R030

Expiry date:

28/02/2031

Notes & Further Information

1.For the series 1044-XX, 1034-XX,1033-XX,1032-XX,1031-XX, the only difference is handle style. 2.XX represent different finishes and can be replaced by CR =Chrome, MB=Matte black, BB=Brushed brass, BN=Brushed nickel,GM=Gun Metal.

Approval Holder:

Zhejiang Carlota Sanitary Ware Manufactory Co.,Ltd

Company Name

Zhejiang Carlota Sanitary Ware Manufactory Co.,Ltd

Address

No.10 Jinbo Road, Bingang Industrial Area, Shamen Town, Yuhuan, Zhejiang Province

Country

China

Phone

0086-13777626837

General Email

305779895@qq.com

View All Listings by this Company

Manufacturers:

Zhejiang Carlota Sanitary Ware Manufactory Co., Ltd

Section:

0551 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and swivel spout, incorporating a manual diverter to a shower outlet

Wall mounted Undefinable AirGap - See IRN's Incorporates a check valve cartridge (however the complete assembly has not been fully tested to demonstrate it provides backflow protection)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

28/02/2031

Approval Holder:

LECICO Plc.

Company Name

LECICO Plc.

Address

2D VIKING INDUSTRIAL ESTATE HUDSON ROAD BEDFORD

Postcode

MK410QB

General Email

jrichards@lecico.co.uk

View All Listings by this Company

Section:

1660 Shower Outlets

Description:

A Shower hose(s)

Stainless steel inter-locked shower hose incorporating an PVC lining and EPDM gaskets.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001

Expiry date:

28/02/2031

Approval Holder:

Yuhuan Jianglin Plumbing Hose & Parts Inc.

Company Name

Yuhuan Jianglin Plumbing Hose & Parts Inc.

Address

2 Jindifu Road, Yuhuan Economic Development Zone, Yuhuan, Zhejiang, 317600

Country

China

Phone

86-576-89901684

General Email

coo@cnjianglin.com

View All Listings by this Company

Manufacturers:

Yuhuan Jianglin Plumbing Hose & Parts lnc.

Section:

1670 Shower Outlets

Description:

A Range of Shower kit(s)

Shower hose EPDM Liner and stainless steel outer finish. All shower handsets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Wall outlets on models JD 744 and JD 795 incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

31/01/2031

Notes & Further Information

The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed

Approval Holder:

Guangzhou KIND Architecture Material Technology Co., Ltd.

Company Name

Guangzhou KIND Architecture Material Technology Co., Ltd.

Address

Unit 10, No.1 Dashadi West, Huangpu District, Guangzhou, Guangdong Province

Postcode

510700

Country

China

Phone

+86-20-23371404

General Email

sale@watersino.com

View All Listings by this Company

Section:

2011 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control, incorporating a manual diverter between outlets.

Wall Mounted Undefinable Air Gap see IRN's

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

28/02/2031

Approval Holder:

Taizhou Xusheng Sanitary Ware Co. Ltd

Company Name

Taizhou Xusheng Sanitary Ware Co. Ltd

Address

No. 1, Lane 318, Binxiang Road, Sanjia Street, Taizhou City,Zhejiang Province,China Taizhou Bay New District, Taizhou City, Zhejiang Province,China

View All Listings by this Company

Manufacturers:

TAI ZHOU XU SHENG SANITARY WARE CO.LTD

Section:

2011 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control, incorporating a manual diverter between outlets.

Wall mounted Undefinable Air Gap – See IRN’s Incorporates a check valve cartridge (however the complete assembly has not been fully tested to demonstrate it provides backflow protection)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

28/02/2031

Notes & Further Information

** denotes finish: No Suffix = Chrome, H = Black, DYB = Matte white, BZ = Perl white painted, HGTS = Red bronze, HTL = Yellow bronze brushed, Q = Bronze, QTSL = Bronze brushed bright, QTS = Bronze brushed matte, STS = Acid copper brushed, SDMGJ = Water plated rose gold, N = Nickel brushed bright light, NP = Nickel brushed, TJ = Titanium gold, TJLS = Titanium gold brushed, G = Gold, GJS = Gold brushed, GJSY = Zirconium gold wire drawing matte, PGJFY = Zirconium gold wire drawing matte bright light, PLSJ = Brushed gold, LSJY = Brushed gold matte, MGJ = Rose gold, MGJL = Rose gold brushed, DMGJ = Light rose gold brushed, HTS = Red bronze brushed, QHP = Grey, LSQH = Grey brushed, LHMGJ = Brushed yellow rose gold.

Approval Holder:

Taizhou Lanbiao Sanitary Ware Co., Ltd

Company Name

Taizhou Lanbiao Sanitary Ware Co., Ltd

Address

XUDOU VILLAGE QINGGANG YUHUAN ZHEJIANG

Postcode

317600

Country

China

Phone

13736601565

General Email

984458082@qq.com

View All Listings by this Company

Manufacturers:

TAIZHOU LANBIAO SANITARY WARE CO., LTD

Section:

2011 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control, incorporating a manual diverter between outlets.

Wall Mounted Concealed Undefinable Air Gap – See IRN’s Models S002 and S014 Incorporates an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides backflow protection)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R020 R040

Expiry date:

31/03/2031

Notes & Further Information

* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black

Approval Holder:

WINSDRUM Technology (Foshan) Co., Ltd

Company Name

WINSDRUM Technology (Foshan) Co., Ltd

Address

Room 804-805, Flat 2, Jiabang Guojin Center, No.1 Shilong South Road, Guicheng Street, Nanhai District, Foshan City, Guangdong Province

Country

China

Phone

0086-19527590441

General Email

carina07@126.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Model B3306AA & B1148AA are supplied with a lever type operated pop-up waste – not verified by test. Products are supplied with 3/8” x 15mm Compression adaptors for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260302011

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The Sandringham models are supplied with an optional flow straightener.

Size:

Stainless steel braided, PEX lined flexible hose assemblies incorporating a 3/8" BSP captive nut end connection with a 3/8" BSP (M) x 15mm compression adapter

Marking:

Armitage Shanks or Ideal Standard on operating member

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

B3306AA – Sandringham 21 – Basin mixer with pop up waste B3307AA – Sandringham 21 – Basin mixer without waste B3308AA – Sandringham 21 – Basin mixer with weighted chain B1148AA – Calista – Basin mixer with pop up waste B1149AA – Calista – Basin mixer without pop up waste

Approval Holder:

Ideal Standard (UK) Ltd

Company Name

Ideal Standard (UK) Ltd

Address

Old Road (Lodge 1) Armitage, Rugeley, Staffordshire

Postcode

WS15 4BT

Country

United Kingdom

General Email

tyeomans@idealstandard.co.uk

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Stainless steel braided, PEX lined flexible hose assemblies incorporating ½” BSP (F) captive nut end connections.

Marking:

BAGNODESIGN on body.

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

BDM-CRL-301S-XX BDM-CRL-302S-XX BDM-FTY-301S-XX BDM-TKG-301S-XX BDM-TKG-302S-XX BDM-TOK-301S-XX BDM-TOK-302S-XX XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308010

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½” BSP Captive nut end connections.

Marking:

BAGNODESIGN on body.

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

BDM-GIN-301S-XX BDM-GIN-302S-XX XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C).

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308015

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Stainless steel braided, PEX lined flexible hose assemblies incorporating ½” BSP (F) captive nut end connections.

Marking:

BAGNODESIGN on body

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

BDM-TEA-301S-A-XX BDM-TEA-302S-XX

Notes & Further Information

XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator, and the product is supplied with a permanently open type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

2304113

Size:

Stainless steel braided PEX lined flexible hose assemblies with ½” BSP captive nut end connections.

Marking:

AQUAECO on base of tap body

Installation Requirements:

R001 R006 R009 R583

Expiry date:

30/04/2028

Model:

AQE-DIP-301-CP AQE-DIP-301S-CP

Notes & Further Information

XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0450 Combination Tap Assemblies

Section Subtitle:

Single hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Stainless steel braided, PEX lined flexible hose assemblies incorporating ½” BSP (F) captive nut end connections.

Marking:

BAGNODESIGN on base of body

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

BDM-ZEP-301S-XX BDM-ZEP-301-XX BDM-ZEP-302S-XX

Notes & Further Information

XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C), Truffle (TF-C) Baby Pink (BP-C) Misty Grey (MG-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Section:

0470 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a swivel spout.

Deck Mounted Capable of achieving AUK3 Tap Gap The product incorporates a check valve that has not been verified by test to provide backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R010

Expiry date:

31/03/2031

Approval Holder:

Franke UK Ltd.

Company Name

Franke UK Ltd.

Address

West Park, MIOC, Styal Road, Manchester

Postcode

M22 5WB

Country

United Kingdom

Phone

0161 4360280

View All Listings by this Company

Manufacturers:

San Marco Rubinetteria S.r.l.

Section:

0470 Combination Tap Assemblies

Description:

A Single hole tap(s) with a single outlet and a swivel spout.

Deck mounted Stainless steel braided EPDM flexible hose assemblies Capable of achieving AUK3 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R010

Expiry date:

31/03/2031

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Wall mounted, two-hole, single outlet, fixed combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headwork with single lever operating members. The spout outlet incorporates a built in anti-splash device and the product is supplied with metal backnuts. Maximum working pressure; 10Bar Maximum operating temperature 85°C

Section:

0510 Combination Tap Assemblies

Section Subtitle:

Two hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260302013

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2" BSP (M)

Marking:

Armitage shanks on indice.

Installation Requirements:

R001 R040

Expiry date:

31/03/2031

Model:

S8230AA

Approval Holder:

Armitage Shanks

Company Name

Armitage Shanks

Address

Old Road (Lodge 1), Armitage, Rugeley

Postcode

WS15 4BT

Country

Staffordshire,

Phone

+44 800 866 966 Fax: 01543 491677 Telex: 339781

View All Listings by this Company

Two-hole, deck mounted, single outlet (fixed) combination tap assembly, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with metal back nuts, a plastic aerator and stainless steel braided EPDM lined interconnecting hoses. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.

Section:

0510 Combination Tap Assemblies

Section Subtitle:

Two hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308003

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Stainless steel braided PEX lined flexible hose assemblies incorporating ½” BSP captive nut end connections.

Marking:

Bagnodesign on operating member.

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/03/2031

Model:

BDM-FTY-304-XX XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C).

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Wall mounted concealed two-hole, single outlet (fixed) combination tap assembly (brass body - various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate an aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0510 Combination Tap Assemblies

Section Subtitle:

Two hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308009

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½’’ BSP (F).

Marking:

Bagnodesign on the escutcheon.

Installation Requirements:

R001 R010 R040

Expiry date:

31/03/2031

Model:

BDM-GIN-305-XX XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C).

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Section:

0520 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and a fixed spout, incorporating a manually operated diverter to a shower outlet.

Deck Mounted. Capable of achieving AUK3 Tap Gap.

Installation Requirements:

R001 R006 R010

Expiry date:

31/03/2031

Notes & Further Information

Where** represents finish and can be replaced by: CR=Chrome plated MB=Matt black BB=Brushed brass BN=Brushed nickel GM=Gun Metal

Product Images

Approval Holder:

Zhejiang Carlota Sanitary Ware Manufactory Co.,Ltd

Company Name

Zhejiang Carlota Sanitary Ware Manufactory Co.,Ltd

Address

No.10 Jinbo Road, Bingang Industrial Area, Shamen Town, Yuhuan, Zhejiang Province

Country

China

Phone

0086-13777626837

General Email

305779895@qq.com

View All Listings by this Company

Manufacturers:

Zhejiang Carlota Sanitary Ware Manufactory Co., Ltd

Section:

0550 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and a swivel spout.

Deck mounted. PEX lined & stainless steel braided Inlet hoses.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R007 R009 R010

Expiry date:

31/10/2030

Model:

53011*

Notes & Further Information

* denotes finish and can be replaced by: C - Chrome RG - Rose Gold BTG - Brushed Titanium gold BZG - Brushed Zirconium gold BRG - Brushed Rose gold MW - Matte white BS - Brushed stainless BN - Brushed nickel PN - Polished nickel GM - Gunmetal B - Matte black TG - Titanium gold ZG - Zirconium gold BC - Black+chrome W - White CW - Chrome+white Q - Quartzite ZGC - Zirconium gold+chrome TGC - Titanium gold+chrome M - Medieval A - Antique bronze CP - Champagne BL - Brushed lead BP - Polished Black

Approval Holder:

Lusso Stone Ltd

Company Name

Lusso Stone Ltd

Address

Lusso House Princeton Drive Stockton

Country

United Kingdom

General Email

customerservice @lusso.com

View All Listings by this Company

Range of three-hole, single outlet (fixed) wall mounted, concealed tap assemblies, (brass bodies - various trim sets). Product is supplied with a rough in set BDM-MIX-C309-T2 and external trim (see models). Incorporating quarter turn ceramic disc headworks and dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0650 Combination Tap Assemblies

Section Subtitle:

Three hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308001

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F) x ½” BSP (F) Rough, ½” BSP (M) trim sets for insertion into rough set.

Marking:

B, on the rough in set, and Bagnodesign on escutcheon or operating member.

Installation Requirements:

R001 R010 R040

Expiry date:

31/03/2031

Model:

BDM-MIX-C309-T2 + BDM-CRL-E309-XX Carlyle 160mm spout. BDM-MIX-C309-T2 + BDM-CRL-E309LS-XX Carlyle 210 mm spout. BDM-MIX-C309-T2 + BDM-FTY-E309-XX Fonteyn. BDM-MIX-C309-T2 + BDM-TKG-E309-XX TOKO Groove flat spout. BDM-MIX-C309-T2 + BDM-TKG-E310-XX TOKO Groove round spout. BDM-MIX-C309-T2 + BDM-TOK-A-E309-XX TOKO XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Range of three-hole, single outlet (fixed) wall mounted, concealed tap assemblies, (brass bodies - various trim sets). Product is supplied with a rough in set BDM-MIX-C309-T2 and external trim (see models). Incorporating quarter turn ceramic disc headworks and various operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:

0650 Combination Tap Assemblies

Section Subtitle:

Three hole tap(s) with a single outlet and a fixed spout.

WRAS Approval Number:

260308013

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2"

Marking:

BAGNODESIGN on spout & faceplate

Installation Requirements:

R001 R010 R040

Expiry date:

31/03/2031

Model:

BDM-MLI-E309-A-XX BDM-BIS-E309X-XX BDM-BIS-E309L-XX BDM-REV-E309-XX BDM-REV-E409-XX

Notes & Further Information

XX’ denotes finish and is replaced with: Chrome(CP), Brushed Nickel (NB), Matt Black(MB), Anthracite (AN), Gold (GD), PVD Gold (PG), Soft Bronze (SBZ), Santiago (RCP), Oyster (OYS), Brushed Steel (BS) Burgundy (BUR), Black (MB-C), Cocoa (CO-C), Mandarin (MD-C), Blueberry (BY-C), Lip Gloss (Pink)(LG-C), Sage (SA-C) & Truffle (TF-C)

Approval Holder:

BAGNODESIGN (SANIPEXGROUP)

Company Name

BAGNODESIGN (SANIPEXGROUP)

Address

Unit 1 Oakwell Park Trading Estate Birstall Leeds

Postcode

WF17 9LU

Country

United Kingdom

General Email

dan@sanipexgroup.com

View All Listings by this Company

Four-hole, single outlet (fixed) combination tap assembly (various finishes). Incorporating quarter turn ceramic disc headworks, with various operating members and stainless steel braided EPDM lined interconnecting hoses. The spout outlet incorporates a self-cancelling diverter to the shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).and a plastic flow straightener with stainless steel mesh strainer. The product is supplied with a shower handset that incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 3.5 bar. Maximum operating temperature 60°C

Section:

0680 Combination Tap Assemblies

Section Subtitle:

Multi hole tap(s) with a single outlet and a swivel spout , incorporating a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3).

WRAS Approval Number:

260304706

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M)

Marking:

THG on spout

Installation Requirements:

R001 R030

Expiry date:

31/03/2031

Model:

112BSG/W – COLLECTION O 112BSGBH/W – COLLECTION O 112BSG/W - DEAN 112BSGBH/W - DEAN 112BSG/W - HAMPTONS 112BSGBH/W – HAMPTONS 112B/W – MOSSI 112BSGBH/W – ZOOM Styles 112BSG/W – COLLECTION O: G6G-New Spirit ; G6H-New Spirit à manettes ; U5P-New Paradise 112BSGBH/W – COLLECTION O G5A-Nano ; G5B-Nano à manettes ; G5D-Anoa 112BSG/W - DEAN G7R-Yoko ; G7S-Yoko Color ; G7T-Yoko Ice ; G7U-Yoko Howlite ; G7V-Yoko Delta ; G7W-Yoko Delta Howlite ; G7X-Yoko - pierre à définir ; G7Y-Yoko Delta - insert pierre (triangle) à définir 112BSGBH/W - DEAN G7G-Bondi à manettes 112BSG/W – HAMPTONS G7H-Club Saint-Germain ; G7J-Club Saint-Germain à manettes ; U3J-Estrela ; U3K-Estrela à manettes ; U3L-Estrela inserts metal. 112BSGBH/W – HAMPTONS G4R-Hamptons ; G4S-Hamptons à manettes 112B/W – MOSSI A4J-Hirondelles ; A4K-Hirondelles tamponnées platine ; A4L-Hirondelles tamponnées or 112BSGBH/W – ZOOM U4J-ZOOM.5 ; U4K-ZOOM.7 ;U4L-ZOOM.12 Finishes A02-Polished Chrome ; A13-Smoked Brass ; B01-Polished Nickel ; C01-Matte Nickel ; C02-Matte Chrome ; C27-Unlacquered Brass ; C47-Smoked Nickel ; D01-Light Bronze Lacquered ; D05-Lacquered Matte Bronze ; D10-USA Oil-Rubbed Bronze ; D12-Polished Brass Lacquered ; D15-Polished Black Lacquered ; D16-White Lacquered ; D18-Matte Black lacquered ; D21-Old Oil-Rubbed Bronze ; D24-Aranja ; H17-Matt Aranja ; F01-Polished Gold ; F07-Matte Gold ; F18-Rhodium Silver ; F19-Matt Rhodium Silver ; F27-Rose Gold ; F30-Soft Gold ; F31-Matte Soft Gold ; F33-Brown Bronze PVD ; F34-Matte Brown Bronze PVD ; G01-Polished Nickel/Polished Gold ; G02-Polished Chrome/Polished Gold ; H03-Lacquered Antique Silver ; H07-Varnished Matte Antique Red Copper ; H08-Lacquered Matte Antique Silver ; H24-Lacquered Antique Copper ; H28-Antique Nickel ; H49-Brass PVD ; H50-Matte Brass PVD ; H52-Gold PVD ; H53-Matte Gold PVD ; H55-Nickel PVD ; H56-Matte Nickel PVD ; H60-Matte Blush PVD ; H62-Blush PVD ; H64-Graphite PVD ; H65-Matte Graphite PVD ; H66-Umber PVD ; H67-Matte Umber PVD For explanation: A complete model number of compiles of a three-digit code from each section above, for example G4S.A02.112BSGBH/W. this would give you Hamptons à manettes and polish chrome finish Single lever basin mixer with waste.

Approval Holder:

THG Paris

Company Name

THG Paris

Address

35 rue Tournière Béthencourt sur Mer

Postcode

80130

Country

France

Phone

+33 3.22.60.20.80

General Email

cvallee@thg.fr

View All Listings by this Company

Manufacturer:

THG Paris

Company Name

THG Paris

Address

35 rue Tournière Béthencourt sur Mer

Postcode

80130

Country

France

Phone

+33 3.22.60.20.80

General Email

cvallee@thg.fr

View All Listings by this Company

Range of expansion vessels with plastic bodies and elastomeric diaphragms. Maximum working pressure: 8.6 Bar. Cold water use only.

Section:

1000 Expansion Vessels

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Pentair, Wellmate, model, pressure, capacity and product info on label on body.

Installation Requirements:

R001 R530 R535

Expiry date:

31/03/2031

Model:

WM0060 – 1” NPT (M), WM0075 – 1” NPT (M), WM0120 – 1” NPT (M), WM0150 – 1” NPT (M), WM0180 – 1 ¼” NPT (M), WM0235 – 1 ¼” NPT (M), WM0330 – 1 ¼” NPT (M), WM0450 – 1 ¼” NPT (M).

Approval Holder:

Pentair Manufacturing

Company Name

Pentair Manufacturing

Address

Belgium bvba Toekomstlaan 30 Herentals, 2200, Belgium

View All Listings by this Company

Range of socket fusion fittings (PP-RCT) for use with PP-RCT “KELEN” pipes. Maximum working pressure 10.0 bar. Maximum operating temperature: 70°C for sizes DN20-DN63 & cold water use only for sizes DN75-DN110.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

260306001

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

20 mm – 110 mm.

Marking:

Pipe: KELEN; size (outer diameter x wall thickness); line and batch no. and traceability information Fitting: KE KELIT or KELIT or KELEN, size and product info

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

“KELEN” PP-RCT pipes: 1702000 KE02 KELEN PP-RCT pipe - PN10 20x1,9 1702500 KE02 KELEN PP-RCT pipe - PN10 25x2,3 1703200 KE02 KELEN PP-RCT pipe - PN10 32x2,9 1704000 KE02 KELEN PP-RCT pipe - PN10 40x3,7 1705000 KE02 KELEN PP-RCT pipe - PN10 50x4,6 1706300 KE02 KELEN PP-RCT pipe - PN10 63x5,8 1707500 KE02 KELEN PP-RCT pipe - PN10 75x6,8 1709000 KE02 KELEN PP-RCT pipe - PN10 90x8,2 1711000 KE02 KELEN PP-RCT pipe - PN10 110x10,0 1682001 KE08 KELEN PP-RCT pipe - PN16 20x2,8 1682501 KE08 KELEN PP-RCT pipe - PN16 25x3,5 1683201 KE08 KELEN PP-RCT pipe - PN16 32x4,4 1684001 KE08 KELEN PP-RCT pipe - PN16 40x5,5 1685001 KE08 KELEN PP-RCT pipe - PN16 50x6,9 1686301 KE08 KELEN PP-RCT pipe - PN16 63x8,6 1687501 KE08 KELEN PP-RCT pipe - PN16 75x10,3 1689001 KE08 KELEN PP-RCT pipe - PN16 90x12,3 1681101 KE08 KELEN PP-RCT pipe - PN16 110x15,1 1620041 KE08-LX4 KELEN PP-RCT LX-SENSO pipe - PN16 20x2,8 1620091 KE08-LX9 KELEN PP-RCT LX-SENSO pipe - PN16 20x2,8 1620131 KE08-LX13 KELEN PP-RCT LX-SENSO pipe - PN16 20x2,8 1625041 KE08-LX4 KELEN PP-RCT LX-SENSO pipe - PN16 25x3,5 1625091 KE08-LX9 KELEN PP-RCT LX-SENSO pipe - PN16 25x3,5 1625131 KE08-LX13 KELEN PP-RCT LX-SENSO pipe - PN16 25x3,5 1632041 KE08-LX4 KELEN PP-RCT LX-SENSO pipe - PN16 32x4,4 1632091 KE08-LX9 KELEN PP-RCT LX-SENSO pipe - PN16 32x4,4 1632131 KE08-LX13 KELEN PP-RCT LX-SENSO pipe - PN16 32x4,4 1502001 KE00 KELEN PP-RCT pipe - PN20 20x3,4 1502501 KE00 KELEN PP-RCT pipe - PN20 25x4,2 1503201 KE00 KELEN PP-RCT pipe - PN20 32x5,4 1504001 KE00 KELEN PP-RCT pipe - PN20 40x6,7 1505001 KE00 KELEN PP-RCT pipe - PN20 50x8,3 1506301 KE00 KELEN PP-RCT pipe - PN20 63x10,5 1507501 KE00 KELEN PP-RCT pipe - PN20 75x12,5 1509001 KE00 KELEN PP-RCT pipe - PN20 90x15,0 1511001 KE00 KELEN PP-RCT pipe - PN20 110x18,3 1520041 KE00-LX4 KELEN PP-RCT LX-SENSO pipe - PN20 20x3,4 1520091 KE00-LX9 KELEN PP-RCT LX-SENSO pipe - PN20 20x3,4 1520131 KE00-LX13 KELEN PP-RCT LX-SENSO pipe - PN20 20x3,4 1525041 KE00-LX4 KELEN PP-RCT LX-SENSO pipe - PN20 25x4,2 1525091 KE00-LX9 KELEN PP-RCT LX-SENSO pipe - PN20 25x4,2 1525131 KE00-LX13 KELEN PP-RCT LX-SENSO pipe - PN20 25x4,2 1532041 KE00-LX4 KELEN PP-RCT LX-SENSO pipe - PN20 32x5,4 1532091 KE00-LX9 KELEN PP-RCT LX-SENSO pipe - PN20 32x5,4 1532131 KE00-LX13 KELEN PP-RCT LX-SENSO pipe - PN20 32x5,4 Couplings 2521501 KE10 2522001 KE10 2522501 KE10 2523001 KE10 2523501 KE10 2524001 KE10 2524501 KE10 2525001 KE10 2525501 KE10 2521541 KE10-LX4 2522041 KE10-LX4 2522541 KE10-LX4 Elbows 2501501 KE20 2502001 KE20 2502501 KE20 2503001 KE20 2503501 KE20 2504001 KE20 2504501 KE20 2505001 KE20 2505501 KE20 2501541 KE20-LX4 2502041 KE20-LX4 2502541 KE20-LX4 2511501 KE70 2512001 KE70 2512501 KE70 2513001 KE70 2513501 KE70 2514001 KE70 2514501 KE70 2515001 KE70 2515501 KE70 2511541 KE70-LX4 2512041 KE70-LX4 2512541 KE70-LX4 2711501 KE26 2712001 KE26 2712501 KE26 2721501 KE27 2722001 KE27 2623501 KE83 2623601 KE83 2623651 KE83 2623701 KE83 2613501 KE21 2615901 KE21 2616001 KE21 2618501 KE21 2603501 KE23 2603601 KE23 2605901 KE23 2606001 KE23 2608501 KE23 Tees 2561501 KE30 2561541 KE30-LX4 2562001 KE30 2562041 KE30-LX4 2562501 KE30 2562541 KE30-LX4 2563001 KE30 2563501 KE30 2564001 KE30 2564501 KE30 2565001 KE30 2565501 KE30 2572001 KE35 2573501 KE35 2573001 KE35 2575001 KE35 2574501 KE35 2574001 KE35 2577001 KE35 2576501 KE35 2576001 KE35 2575501 KE35 2579001 KE35 2578501 KE35 2578001 KE35 2577501 KE35 2579801 KE35 2579601 KE35 2579401 KE35 2579201 KE35 2579051 KE35 2579101 KE35 2579151 KE35 2579301 KE35 2579351 KE35 2572041 KE35-LX4 2573541 KE35-LX4 2573041 KE35-LX4 2580141 KE36-LX4 2580041 KE36-LX4 2580241 KE36-LX4 2580341 KE36-LX4 2580441 KE36-LX4 2580541 KE36-LX4 2580741 KE36-LX4 2580101 KE36 2580001 KE36 2580201 KE36 2580301 KE36 2580401 KE36 2580501 KE36 2580601 KE36 2580701 KE36 2572101 KE38 2643501 KE31 2643601 KE31 2646001 KE31 2648601 KE31 2643701 KE31LA 2633501 KE33 2633601 KE33 2634001 KE33 2636001 KE33 2638501 KE33 2633701 KE33HA Reducer 2453501 KE41 2652001 KE41 2653001 KE41 2654001 KE41 2654501 KE41 2655001 KE41 2655501 KE41 2656001 KE41 2656501 KE41 2657001 KE41 2657301 KE41 2657601 KE41 2657901 KE41 2658201 KE41 2659001 KE41 2659101 KE41 2659501 KE41 2659801 KE41 2772001 KE41 2772101 KE41 2772201 KE41 Saddle fittings 2472001 KE47 2472501 KE47 2475001 KE47 2475501 KE47 2472051 KE43 2472061 KE43 2475051 KE43 2475061 KE43 2477051 KE44 End caps 2551501 KE60 2552001 KE60 2552501 KE60 2553001 KE60 2553501 KE60 2554001 KE60 2554501 KE60 2555001 KE60 2555501 KE60 2552101 KE61 Curved pipes 2541501 KE90 2542001 KE90 2542501 KE90 2541541 KE90-LX4 2542041 KE90-LX4 2542541 KE90-LX4 Male threads 2593501 KE11 2594001 KE11 2595501 KE11 2596001 KE11 2598001 KE11 2598501 KE11 2598801 KE11 2599001 KE11 2599501 KE11 2599801 KE11 2600001 KE11 Female threads 2583501 KE13 2584001 KE13 2585501 KE13 2586001 KE13 2588001 KE13 2588601 KE13 2588801 KE13 2589001 KE13 2589501 KE13 2589801 KE13 2590001 KE13 Union fittings 2742001 KE55 2742501 KE55 2743001 KE55 2743501 KE55 2744001 KE55 2744501 KE55 2752001 KE56 2752501 KE56 2753001 KE56 2753501 KE56 2754001 KE56 2754501 KE56

Approval Holder:

KE KELIT

Company Name

KE KELIT

Address

Kunstsoffwerk Gesellschaft m.b.h

View All Listings by this Company

Range of stainless-steel (304/316L) press fittings with EPDM ‘O-rings to be used with stainless-steel (304/316L) pipes. The HF fittings also incorporate an EPDM gasket. Jointing is achieved via a crimping tool using a ‘V’ profile. For above ground use. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

260315002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

18mm - 108mm. ½” - 4” BSP (M) or (F). ½” - 2” captive nut.

Marking:

N·U (brand logo of Meide Archung), material, EN 10312, model number, size and batch number on fitting body. N·U (brand logo of Meide Archung) Stainless steel pipe, size, material, EN 10312 and batch number on pipe. As of 24/03/2026 N∙U or MECH or meide logo, model number, batch number, size, EN 10312 and material on fitting body. N∙U or MECH or meide logo, batch number, size, EN 10312 and material on pipe. Location of marking, e.g. on valve body, laser etched on cover: On fitting body and pipe.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

PX - Stainless Steel Pipe: 18X1.0, 22X1.2, 28X1.2, 35X1.5, 42X1.5, 54X1.5, 76.1X2.0, 88.9X2.0, 108X2.0. S - Straight Coupling: 18x18, 22x22, 28x28, 35x35, 42x42, 54x54, 76.1x76.1, 88.9x88.9, 108x108. SR - Reducing Coupling: 22X18, 28X18, 28X22, 35X18, 35X22, 35X28, 42X28, 42X35, 54X28, 54X35, 54X42, 76.1X42, 76.1X54, 88.9X42, 88.9X54, 88.9X76.1, 108X54, 108X76.1, 108X88.9. SK - Adjustable Coupling: 18x18, 22x22, 28x28, 35x35, 42x42, 54x54, 76.1x76.1, 88.9x88.9, 108x108. SF - Female Coupling: 18x1/2", 22x3/4", 28x1", 35x1-1/4", 42x1-1/2", 54x2", 76.1x2-1/2", 88.9x3", 108x4". SRF - Female Reducing Coupling: 22x1/2", 28x3/4", 35x1", 42x1-1/4", 54x1-1/2". SM - Male Coupling: 18x1/2", 22x3/4", 28x1", 35x1-1/4", 42x1-1/2", 54x2", 76.1x2-1/2", 88.9x3", 108x4". SRM - Male Reducing Coupling: 22x1/2", 28x1/2", 28x3/4", 35x1/2", 35x3/4", 35x1", 42x1/2", 42x1", 42x1-1/4", 54x1-1/2". HF - Female Straight Swivel: 18x1/2", 22x3/4", 28x1", 35x1-1/4", 42x1-1/2", 54x2". 90E - 90°elbow: 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. 90D - 90° elbow (single-direction): 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. 90F - 90° female elbow: 18x1/2", 22x3/4", 28x1", 35x1-1/4", 42x1-1/2", 54x2". 90RF - 90° reducing female elbow: 22x1/2", 28x1/2", 28x3/4", 35x1/2", 35x1", 42x1-1/4", 54x1-1/2". 90M - 90° male elbow: 18x1/2", 22x3/4", 28x1", 35x1-1/4", 42x1-1/2", 54x2". 90RM - 90° Reducing male elbow: 22x1/2", 28x1/2", 28x3/4", 35x1", 42x1-1/4", 54x1-1/2". 90FZ - 90° short female elbow: 18x1/2", 22x3/4", 28x1", 22x1/2". T - Equal tee: 18x18x18, 22x22x22, 28x28x28, 35x35x35, 42x42x42, 54x54x54, 76.1x76.1x76.1, 88.9x88.9x88.9, 108x108x108. TR - Reducing Tee: 22x18x22, 28x18x28, 28x22x28, 35x18x35, 35x22x35, 35x28x35, 42x18x42, 42x22x42, 42x28x42, 42x35x42, 54x18x54, 54x22x54, 54x28x54, 54x35x54, 54x42x54, 76.1x42x76.1, 76.1x54x76.1, 88.9x54x88.9, 88.9x76.1x88.9, 108x22x108, 108x28x108, 108x35x108, 108x42x108, 108x54x108, 108x76.1x108, 108x88.9x108. TF - Female equal tee: 18x1/2"x18, 22x3/4"x22, 28x1"x28, 35x1-1/4"x35, 42x1-1/2"x42, 54x2"x54. TRF - Female reducing tee: 22x1/2"x22, 28x1/2"x28, 28x3/4"x28, 35x1/2"x35, 35x3/4"x35, 35x1"x35, 42x1/2"x42, 42X3/4"x42, 42x1"x42, 42x1-1/4"x42, 54x1/2"x54, 54X3/4"x54, 54X1"x54, 54X1-1/4"x54, 54x1-1/2"x54, 108X2"x108. TM - Male equal tee: 18x1/2"x18, 22x3/4"x22, 28x1"x28, 35x1-1/4"x35, 42x1-1/2"x42, 54x2"x54. TRM - Male reducing tee: 22x1/2"x22, 28x1/2"x28, 28x3/4"x28, 35x1/2"x35, 35x3/4"x35, 35x1"x35, 42x1/2"x42, 42X3/4"x42, 42x1"x42, 42x1-1/4"x42, 54x1/2"x54, 54X3/4"x54, 54X1"x54, 54X1-1/4"x54, 54x1-1/2"x54. 45E - 45° elbow: 18x18, 22x22, 28x28, 35x35, 42x42, 54x54, 76.1x76.1, 88.9x88.9, 108x108. 45D - 45° elbow (single-direction): 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. C - Cap: 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108. Q - Pipe bridge: 18, 22, 28.

Approval Holder:

Jinan Meide Casting Co., Ltd

Company Name

Jinan Meide Casting Co., Ltd

Address

NO.1 MEIDE STREET, MEIGUI TOWN, PINGYIN COUNTY, JINAN, SHANDONG 250400

Country

China

View All Listings by this Company

Manufacturer:

Meide Archung (Deqing) Pipe Co., Ltd

Company Name

Meide Archung (Deqing) Pipe Co., Ltd

Address

Industrial Intensive Ecological Base Stainless Steel City, Deqing County, Zhaoqing City, Guangdong

Country

China

View All Listings by this Company

VSH XPRESS Range of ‘M’ profile stainless steel press fittings with EPDM ‘O’-rings for use with VSH SudoXPress stainless steel tube. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250604032

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Xpress - steel grade and size on body of fitting.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

6117914 VSH SudoXPress Stainless tube 1.4401 (AISI316) 15x1.0 (l=6m) 6117925 VSH SudoXPress Stainless tube 1.4401 (AISI316) 18x1.0 (l=6m) 6117936 VSH SudoXPress Stainless tube 1.4401 (AISI316) 22x1.2 (l=6m) 6117947 VSH SudoXPress Stainless tube 1.4401 (AISI316) 28x1.2 (l=6m) 6117958 VSH SudoXPress Stainless tube 1.4401 (AISI316) 35x1.5 (l=6m) 6117969 VSH SudoXPress Stainless tube 1.4401 (AISI316) 42x1.5 (l=6m) 6117971 VSH SudoXPress Stainless tube 1.4401 (AISI316) 54x1.5 (l=6m) 6117980 VSH SudoXPress Stainless tube 1.4401 (AISI316) 76.1x2.0 (l=6m) 6117991 VSH SudoXPress Stainless tube 1.4401 (AISI316) 88.9x2.0 (l=6m) 6118002 VSH SudoXPress Stainless tube 1.4401 (AISI316) 108x2.0 (l=6m) 6118178 VSH SudoXPress Stainless tube 1.4301 (AISI304) 76.1x2.0 6118189 VSH SudoXPress Stainless tube 1.4301 (AISI304) 88.9x2.0 6118200 VSH SudoXPress Stainless tube 1.4301 (AISI304) 108x2.0 6190008 VSH XPress Stainless bend pipe 15° ØØ 28 6190019 VSH XPress Stainless bend pipe 15° ØØ 35 6190021 VSH XPress Stainless bend pipe 30° ØØ 28 6190030 VSH XPress Stainless bend pipe 30° ØØ 35 6190041 VSH XPress Stainless bend 45° FF 15 6190052 VSH XPress Stainless bend 45° FF 18 6190063 VSH XPress Stainless bend 45° FF 22 6190074 VSH XPress Stainless bend 45° FF 28 6190085 VSH XPress Stainless bend 45° FF 35 6190096 VSH XPress Stainless bend 45° FF 42 6190107 VSH XPress Stainless bend 45° FF 54 6190118 VSH XPress Stainless bend 45° FØ 15 6190129 VSH XPress Stainless bend 45° FØ 18 6190131 VSH XPress Stainless bend 45° FØ 22 6190140 VSH XPress Stainless bend 45° FØ 28 6190151 VSH XPress Stainless bend 45° FØ 35 6190162 VSH XPress Stainless bend 45° FØ 42 6190173 VSH XPress Stainless bend 45° FØ 54 6190184 VSH XPress Stainless bend pipe 60° ØØ 28 6190195 VSH XPress Stainless bend pipe 60° ØØ 35 6190206 VSH XPress Stainless bend 90° FF 15 6190217 VSH XPress Stainless bend 90° FF 18 6190228 VSH XPress Stainless bend 90° FF 22 6190239 VSH XPress Stainless bend 90° FF 28 6190241 VSH XPress Stainless bend 90° FF 35 6190250 VSH XPress Stainless bend 90° FF 42 6190261 VSH XPress Stainless bend 90° FF 54 6190272 VSH XPress Stainless bend pipe 90° ØØ 15 6190283 VSH XPress Stainless bend pipe 90° ØØ 18 6190294 VSH XPress Stainless bend pipe 90° ØØ 22 6190305 VSH XPress Stainless bend pipe 90° ØØ 28 6190316 VSH XPress Stainless bend pipe 90° ØØ 35 6190327 VSH XPress Stainless bend pipe 90° ØØ 42 6190338 VSH XPress Stainless bend pipe 90° ØØ 54 6190349 VSH XPress Stainless bend 90° FØ 15 6190351 VSH XPress Stainless bend 90° FØ 18 6190360 VSH XPress Stainless bend 90° FØ 22 6190371 VSH XPress Stainless bend 90° FØ 28 6190382 VSH XPress Stainless bend 90° FØ 35 6190393 VSH XPress Stainless bend 90° FØ 42 6190404 VSH XPress Stainless bend 90° FØ 54 6190415 VSH XPress Stainless straight connector FF 15xRp1/2" 6190426 VSH XPress Stainless straight connector FF 15xRp3/4" 6190437 VSH XPress Stainless straight connector FF 18xRp1/2" 6190448 VSH XPress Stainless straight connector FF 18xRp3/4" 6190459 VSH XPress Stainless straight connector FF 22xRp1" 6190461 VSH XPress Stainless straight connector FF 22xRp1/2" 6190470 VSH XPress Stainless straight connector FF 22xRp3/4" 6190481 VSH XPress Stainless straight connector FF 28xRp1" 6190492 VSH XPress Stainless straight connector FF 28xRp1 1/4" 6190503 VSH XPress Stainless straight connector FF 28xRp3/4" 6190514 VSH XPress Stainless straight connector FF 35xRp1" 6190525 VSH XPress Stainless straight connector FF 35xRp1 1/2" 6190536 VSH XPress Stainless straight connector FF 35xRp1 1/4" 6190547 VSH XPress Stainless straight connector FF 42xRp1 1/2" 6190558 VSH XPress Stainless straight connector FF 42xRp1 1/4" 6190569 VSH XPress Stainless straight connector FF 54xRp1 1/2" 6190571 VSH XPress Stainless straight connector FF 54xRp2" 6190580 VSH XPress Stainless straight connector FM 15xR1/2" 6190591 VSH XPress Stainless straight connector FM 15xR3/4" 6190602 VSH XPress Stainless straight connector FM 18xR1/2" 6190613 VSH XPress Stainless straight connector FM 18xR3/4" 6190624 VSH XPress Stainless straight connector FM 22xR1" 6190635 VSH XPress Stainless straight connector FM 22xR1/2" 6190646 VSH XPress Stainless straight connector FM 22xR3/4" 6190657 VSH XPress Stainless straight connector FM 28xR1" 6190668 VSH XPress Stainless straight connector FM 28xR1 1/4" 6190679 VSH XPress Stainless straight connector FM 28xR3/4" 6190681 VSH XPress Stainless straight connector FM 35xR1" 6190690 VSH XPress Stainless straight connector FM 35xR1 1/2" 6190701 VSH XPress Stainless straight connector FM 35xR1 1/4" 6190712 VSH XPress Stainless straight connector FM 42xR1 1/2" 6190723 VSH XPress Stainless straight connector FM 42xR1 1/4" 6190734 VSH XPress Stainless straight connector FM 54xR1 1/2" 6190745 VSH XPress Stainless straight connector FM 54xR2" 6190756 VSH XPress Stainless flange adapter PN10/16 15 DN15 6190767 VSH XPress Stainless flange adapter PN10/16 18 DN15 6190778 VSH XPress Stainless flange adapter PN10/16 22 DN20 6190789 VSH XPress Stainless flange adapter PN10/16 28 DN25 6190791 VSH XPress Stainless flange adapter PN10/16 35 DN32 6190800 VSH XPress Stainless flange adapter PN10/16 42 DN40 6190811 VSH XPress Stainless flange adapter PN10/16 54 DN50 6190822 VSH XPress Stainless angle adapter 90° FF 15xRp1/2" 6190833 VSH XPress Stainless angle adapter 90° FF 18xRp1/2" 6190844 VSH XPress Stainless angle adapter 90° FF 22xRp3/4" 6190855 VSH XPress Stainless angle adapter 90° FF 28xRp1" 6190866 VSH XPress Stainless angle adapter 90° FF 35xRp1 1/4" 6190877 VSH XPress Stainless angle adapter 90° FM 15xR1/2" 6190888 VSH XPress Stainless angle adapter 90° FM 18xR1/2" 6190899 VSH XPress Stainless angle adapter 90° FM 22xR3/4" 6190901 VSH XPress Stainless angle adapter 90° FM 28xR1" 6190910 VSH XPress Stainless angle adapter 90° FM 35xR1 1/4" 6190921 VSH XPress Stainless angle adapter 90° FM 42xR1 1/2" 6190932 VSH XPress Stainless angle adapter 90° FM 54xR2" 6190943 VSH XPress Stainless straight coupling FF 15 6190954 VSH XPress Stainless straight coupling FF 18 6190965 VSH XPress Stainless straight coupling FF 22 6190976 VSH XPress Stainless straight coupling FF 28 6190987 VSH XPress Stainless straight coupling FF 35 6190998 VSH XPress Stainless straight coupling FF 42 6191009 VSH XPress Stainless straight coupling FF 54 6191011 VSH XPress Stainless stop end F 15 6191020 VSH XPress Stainless stop end F 18 6191031 VSH XPress Stainless stop end F 22 6191042 VSH XPress Stainless stop end F 28 6191053 VSH XPress Stainless stop end F 35 6191064 VSH XPress Stainless stop end F 42 6191075 VSH XPress Stainless stop end F 54 6191086 VSH XPress Stainless crossover ØØ 15 6191097 VSH XPress Stainless crossover ØØ 18 6191108 VSH XPress Stainless crossover ØØ 22 6191119 VSH XPress Stainless crossover ØØ 28 6191121 VSH XPress Stainless reducer ØF 18x15 6191130 VSH XPress Stainless reducer ØF 22x15 6191141 VSH XPress Stainless reducer ØF 22x18 6191152 VSH XPress Stainless reducer ØF 28x15 6191163 VSH XPress Stainless reducer ØF 28x18 6191174 VSH XPress Stainless reducer ØF 28x22 6191185 VSH XPress Stainless reducer ØF 35x18 6191196 VSH XPress Stainless reducer ØF 35x22 6191207 VSH XPress Stainless reducer ØF 35x28 6191218 VSH XPress Stainless reducer ØF 42x22 6191229 VSH XPress Stainless reducer ØF 42x28 6191231 VSH XPress Stainless reducer ØF 42x35 6191240 VSH XPress Stainless reducer ØF 54x22 6191251 VSH XPress Stainless reducer ØF 54x28 6191262 VSH XPress Stainless reducer ØF 54x35 6191273 VSH XPress Stainless reducer ØF 54x42 6191284 VSH XPress Stainless slip coupling FF 15 6191295 VSH XPress Stainless slip coupling FF 18 6191306 VSH XPress Stainless slip coupling FF 22 6191317 VSH XPress Stainless slip coupling FF 28 6191328 VSH XPress Stainless slip coupling FF 35 6191339 VSH XPress Stainless slip coupling FF 42 6191341 VSH XPress Stainless slip coupling FF 54 6191350 VSH XPress Stainless T-piece FFF 15 6191361 VSH XPress Stainless T-piece reduced FFF 18x18x15 6191372 VSH XPress Stainless T-piece FFF 18 6191383 VSH XPress Stainless T-piece reduced FFF 22x22x15 6191394 VSH XPress Stainless T-piece reduced FFF 22x22x18 6191405 VSH XPress Stainless T-piece FFF 22 6191416 VSH XPress Stainless T-piece reduced FFF 28x28x15 6191427 VSH XPress Stainless T-piece reduced FFF 28x28x18 6191438 VSH XPress Stainless T-piece reduced FFF 28x28x22 6191449 VSH XPress Stainless T-piece FFF 28 6191451 VSH XPress Stainless T-piece reduced FFF 35x35x15 6191460 VSH XPress Stainless T-piece reduced FFF 35x35x18 6191471 VSH XPress Stainless T-piece reduced FFF 35x35x22 6191482 VSH XPress Stainless T-piece reduced FFF 35x35x28 6191493 VSH XPress Stainless T-piece FFF 35 6191504 VSH XPress Stainless T-piece reduced FFF 42x42x22 6191515 VSH XPress Stainless T-piece reduced FFF 42x42x28 6191526 VSH XPress Stainless T-piece reduced FFF 42x42x35 6191537 VSH XPress Stainless T-piece FFF 42 6191548 VSH XPress Stainless T-piece reduced FFF 54x54x22 6191559 VSH XPress Stainless T-piece reduced FFF 54x54x28 6191561 VSH XPress Stainless T-piece reduced FFF 54x54x35 6191570 VSH XPress Stainless T-piece reduced FFF 54x54x42 6191581 VSH XPress Stainless T-piece FFF 54 6191592 VSH XPress Stainless T-piece female thread FFF 15x15xRp1/2" 6191603 VSH XPress Stainless T-piece female thread FFF 18x18xRp1/2" 6191614 VSH XPress Stainless T-piece female thread FFF 18x18xRp3/4" 6191625 VSH XPress Stainless T-piece female thread FFF 22x22xRp1/2" 6191636 VSH XPress Stainless T-piece female thread FFF 22x22xRp3/4" 6191647 VSH XPress Stainless T-piece female thread FFF 28x28xRp1/2" 6191658 VSH XPress Stainless T-piece female thread FFF 28x28xRp3/4" 6191669 VSH XPress Stainless T-piece female thread FFF 35x35xRp1/2" 6191671 VSH XPress Stainless T-piece female thread FFF 35x35xRp3/4" 6191680 VSH XPress Stainless T-piece female thread FFF 42x42xRp1/2" 6191691 VSH XPress Stainless T-piece female thread FFF 42x42xRp3/4" 6191702 VSH XPress Stainless T-piece female thread FFF 54x54xRp1/2" 6191713 VSH XPress Stainless T-piece female thread FFF 54x54xRp2" 6191724 VSH XPress Stainless T-piece female thread FFF 54x54xRp3/4" 6191735 VSH XPress Stainless coupling with nut FF 15xG3/4" 6191746 VSH XPress Stainless coupling with nut FF 18xG3/4" 6191757 VSH XPress Stainless coupling with nut FF 22xG1" 6191768 VSH XPress Stainless coupling with nut FF 28xG1 1/4" 6191779 VSH XPress Stainless coupling with nut FF 35xG1 1/2" 6191781 VSH XPress Stainless coupling with nut FF 42xG1 3/4" 6191790 VSH XPress Stainless coupling with nut FF 54xG2 3/8" 6191801 VSH XPress Stainless wall plate FF 15xRp1/2" 6191812 VSH XPress Stainless wall plate FF 18xRp1/2" 6191823 VSH XPress Stainless wall plate FF 22xRp3/4" 6191834 VSH XPress Stainless bend pipe 15° ØØ 42 6191845 VSH XPress Stainless bend pipe 15° ØØ 54 6191856 VSH XPress Stainless bend pipe 30° ØØ 42 6191867 VSH XPress Stainless bend pipe 30° ØØ 54 6191878 VSH XPress Stainless bend pipe 60° ØØ 42 6191889 VSH XPress Stainless bend pipe 60° ØØ 54 6191891 VSH XPress Stainless coupling for flat seal F 15x1 1/8" 6191900 VSH XPress Stainless coupling for flat seal F 15x1 1/2" 6191911 VSH XPress Stainless coupling for flat seal F 18x1 1/4" 6191922 VSH XPress Stainless coupling for flat seal F 18x1 1/2" 6191933 VSH XPress Stainless coupling for flat seal F 22x1 1/4" 6191944 VSH XPress Stainless coupling for flat seal F 22x1 1/2" 6191955 VSH XPress Stainless coupling for flat seal F 28x1 1/2" 6191966 VSH XPress Stainless coupling for flat seal F 35x2" 6191977 VSH XPress Stainless coupling for flat seal F 42x2 1/4" 6191988 VSH XPress Stainless coupling for flat seal F 54x2 3/4" 6191999 VSH XPress Stainless wall plate long 90° FF 15xRp1/2" 6192001 VSH XPress Stainless wall plate long 90° FF 18xRp1/2" 6192010 VSH XPress Stainless wall plate long 90° FF 22xRp3/4" 6192021 VSH XPress Stainless straight union FF 15xRp1/2" 6192032 VSH XPress Stainless straight union FF 15xRp3/4" 6192043 VSH XPress Stainless straight union FF 18xRp1/2" 6192054 VSH XPress Stainless straight union FF 18xRp3/4" 6192065 VSH XPress Stainless straight union FF 22xRp3/4" 6192076 VSH XPress Stainless straight union FF 22xRp1" 6192087 VSH XPress Stainless straight union FF 28xRp1" 6192098 VSH XPress Stainless straight union FF 35xRp1 1/4" 6192109 VSH XPress Stainless straight union FF 42xRp1 1/2" 6192111 VSH XPress Stainless straight union FF 54xRp2" 6192120 VSH XPress Stainless straight union FM 15xR1/2" 6192131 VSH XPress Stainless straight union FM 15xR3/4" 6192142 VSH XPress Stainless straight union FM 18xR1/2" 6192153 VSH XPress Stainless straight union FM 18xR3/4" 6192164 VSH XPress Stainless straight union FM 22xR1/2" 6192175 VSH XPress Stainless straight union FM 22xR3/4" 6192186 VSH XPress Stainless straight union FM 22xR1" 6192197 VSH XPress Stainless straight union FM 28xR1" 6192208 VSH XPress Stainless straight union FM 35xR1 1/4" 6192219 VSH XPress Stainless straight union FM 42xR1 1/2" 6192221 VSH XPress Stainless reducer ØF 35x15 6192230 VSH XPress Stainless reducer ØF 42x15 6192241 VSH XPress Stainless reducer ØF 42x18 6192252 VSH XPress Stainless reducer ØF 54x15 6192263 VSH XPress Stainless reducer ØF 54x18 6192274 VSH XPress Stainless angle adapter 90° ØF 15xRp1/2" 6192285 VSH XPress Stainless wall plate FFF 15x15xRp1/2" 6192296 VSH XPress Stainless straight union FM 54xR2" 6192307 VSH SudoXPress Stainless tube 1.4401 (AISI316) 15x1.0 (l=6m) small bundle 6192318 VSH SudoXPress Stainless tube 1.4401 (AISI316) 18x1.0 (l=6m) small bundle 6192329 VSH SudoXPress Stainless tube 1.4401 (AISI316) 22x1.2 (l=6m) small bundle 6192331 VSH SudoXPress Stainless tube 1.4401 (AISI316) 28x1.2 (l=6m) small bundle 6192340 VSH SudoXPress Stainless tube 1.4401 (AISI316) 35x1.5 (l=6m) small bundle 6192351 VSH SudoXPress Stainless tube 1.4401 (AISI316) 42x1.5 (l=6m) small bundle 6192362 VSH SudoXPress Stainless tube 1.4401 (AISI316) 54x1.5 (l=6m) small bundle 6192406 VSH SudoXPress Stainless tube 1.4521 (AISI444) 15x1.0 small bundle 6192417 VSH SudoXPress Stainless tube 1.4521 (AISI444) 18x1.0 small bundle 6192428 VSH SudoXPress Stainless tube 1.4521 (AISI444) 22x1.2 small bundle 6192439 VSH SudoXPress Stainless tube 1.4521 (AISI444) 28x1.2 small bundle 6192441 VSH SudoXPress Stainless tube 1.4521 (AISI444) 35x1.5 small bundle 6192450 VSH SudoXPress Stainless tube 1.4521 (AISI444) 42x1.5 small bundle 6192461 VSH SudoXPress Stainless tube 1.4521 (AISI444) 54x1.5 small bundle 6193077 VSH SudoXPress Stainless tube 1.4301 (AISI304) 15x1.0 small bundle 6193308 VSH XPress Stainless straight connector FF 28xRp1/2" 6193319 VSH XPress Stainless groove connector FM 76.1x76.1 6193321 VSH XPress Stainless groove connector FM 88.9x88.9 6193330 VSH XPress Stainless groove connector FM 114x108 6193407 VSH SudoXPress Stainless tube 1.4301 (AISI304) 15x1.0 6193418 VSH SudoXPress Stainless tube 1.4301 (AISI304) 18x1.0 6193429 VSH SudoXPress Stainless tube 1.4301 (AISI304) 22x1.2 6193431 VSH SudoXPress Stainless tube 1.4301 (AISI304) 28x1.2 6193440 VSH SudoXPress Stainless tube 1.4301 (AISI304) 35x1.5 6193451 VSH SudoXPress Stainless tube 1.4301 (AISI304) 42x1.5 6193462 VSH SudoXPress Stainless tube 1.4301 (AISI304) 54x1.5 6194001 VSH SudoXPress Stainless tube 1.4521 (AISI444) 15x1.0 (l=6m) 6194012 VSH SudoXPress Stainless tube 1.4521 (AISI444) 18x1.0 (l=6m) 6194023 VSH SudoXPress Stainless tube 1.4521 (AISI444) 22x1.2 (l=6m) 6194034 VSH SudoXPress Stainless tube 1.4521 (AISI444) 28x1.2 (l=6m) 6194045 VSH SudoXPress Stainless tube 1.4521 (AISI444) 35x1.5 (l=6m) 6194056 VSH SudoXPress Stainless tube 1.4521 (AISI444) 42x1.5 (l=6m) 6194067 VSH SudoXPress Stainless tube 1.4521 (AISI444) 54x1.5 (l=6m) 6195079 VSH SudoXPress Stainless tube 1.4301 (AISI304) 76.1x2.0 small bundle 6195081 VSH SudoXPress Stainless tube 1.4301 (AISI304) 88.9x2.0 small bundle 6195090 VSH SudoXPress Stainless tube 1.4301 (AISI304) 108x2.0 small bundle 6196003 VSH SudoXPress Stainless tube 1.4301 (AISI304) 18x1.0 small bundle 6196014 VSH SudoXPress Stainless tube 1.4301 (AISI304) 22x1.2 small bundle 6196025 VSH SudoXPress Stainless tube 1.4301 (AISI304) 28x1.2 small bundle 6196036 VSH SudoXPress Stainless tube 1.4301 (AISI304) 35x1.5 small bundle 6196047 VSH SudoXPress Stainless tube 1.4301 (AISI304) 42x1.5 small bundle 6196058 VSH SudoXPress Stainless tube 1.4301 (AISI304) 54x1.5 small bundle 6198302 VSH XPress Stainless axial compensator FF 15 6198313 VSH XPress Stainless axial compensator FF 18 6198324 VSH XPress Stainless axial compensator FF 22 6198335 VSH XPress Stainless axial compensator FF 28 6198346 VSH XPress Stainless axial compensator FF 35 6198357 VSH XPress Stainless axial compensator FF 42 6198368 VSH XPress Stainless axial compensator FF 54 6198379 VSH XPress Stainless axial compensator ØØ 76.1 6198381 VSH XPress Stainless axial compensator ØØ 88.9 6198390 VSH XPress Stainless axial compensator ØØ 108 6198456 VSH XPress Stainless angle adapter 90° FF 22xRp1/2" 6198467 VSH XPress Stainless angle adapter 90° FF 28xRp1/2" 6198478 VSH XPress Stainless angle adapter 90° FF 28xRp3/4" 6198489 VSH XPress Stainless angle adapter 90° FF 35xRp1/2" 6198491 VSH XPress Stainless angle adapter 90° FF 35xRp3/4" 6198500 VSH XPress Stainless angle adapter 90° FF 35xRp1" 6198511 VSH XPress Stainless slip coupling FF 22xRp1/2" 6198522 VSH XPress Stainless slip coupling FF 22xRp3/4" 6198533 VSH XPress Stainless slip coupling FF 28xRp1/2" 6198544 VSH XPress Stainless slip coupling FF 28xRp3/4" 6198555 VSH XPress Stainless groove connector FM 28x33.7 6198566 VSH XPress Stainless groove connector FM 35x42.4 6198577 VSH XPress Stainless groove connector FM 42x48.3 6198588 VSH XPress Stainless groove connector FM 54x60.3 6198599 VSH XPress Stainless T-piece female thread FFF 28x28xRp1" 6198601 VSH XPress Stainless T-piece female thread FFF 35x35xRp1" 6198610 VSH XPress Stainless T-piece female thread FFF 42x42xRp1" 6198621 VSH XPress Stainless T-piece female thread FFF 54x54xRp1" 6198929 VSH XPress Stainless straight connector FM 12xR1/2" 6204121 VSH XPress Stainless flange adapter PN10/16 76.1 DN65 6204132 VSH XPress Stainless flange adapter PN10/16 88.9 DN80 6204143 VSH XPress Stainless flange adapter PN10/16 108 DN100 6204154 VSH XPress Stainless straight coupling FF 76.1 6204165 VSH XPress Stainless straight coupling FF 88.9 6204176 VSH XPress Stainless straight coupling FF 108 6204187 VSH XPress Stainless stop end F 76.1 6204198 VSH XPress Stainless stop end F 88.9 6204209 VSH XPress Stainless stop end F 108 6204211 VSH XPress Stainless reducer ØF 76.1x42 6204220 VSH XPress Stainless reducer ØF 76.1x54 6204231 VSH XPress Stainless reducer ØF 88.9x54 6204242 VSH XPress Stainless reducer ØF 88.9x76.1 6204253 VSH XPress Stainless reducer ØF 108x54 6204264 VSH XPress Stainless reducer ØF 108x76.1 6204275 VSH XPress Stainless reducer ØF 108x88.9 6204286 VSH XPress Stainless slip coupling FF 76.1 6204297 VSH XPress Stainless slip coupling FF 88.9 6204308 VSH XPress Stainless slip coupling FF 108 6204319 VSH XPress Stainless T-piece FFF 76.1 6204321 VSH XPress Stainless T-piece FFF 88.9 6204330 VSH XPress Stainless T-piece FFF 108 6204341 VSH XPress Stainless T-piece reduced FFF 76.1x76.1x22 6204352 VSH XPress Stainless T-piece reduced FFF 76.1x76.1x28 6204363 VSH XPress Stainless T-piece reduced FFF 76.1x76.1x35 6204374 VSH XPress Stainless T-piece reduced FFF 76.1x76.1x42 6204385 VSH XPress Stainless T-piece reduced FFF 76.1x76.1x54 6204396 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x22 6204407 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x28 6204418 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x35 6204429 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x42 6204431 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x54 6204440 VSH XPress Stainless T-piece reduced FFF 88.9x88.9x76.1 6204451 VSH XPress Stainless T-piece reduced FFF 108x108x22 6204462 VSH XPress Stainless T-piece reduced FFF 108x108x28 6204473 VSH XPress Stainless T-piece reduced FFF 108x108x35 6204484 VSH XPress Stainless T-piece reduced FFF 108x108x42 6204495 VSH XPress Stainless T-piece reduced FFF 108x108x54 6204506 VSH XPress Stainless T-piece reduced FFF 108x108x76.1 6204517 VSH XPress Stainless T-piece reduced FFF 108x108x88.9 6204528 VSH XPress Stainless T-piece female thread FFF 76.1x76.1xRp3/4" 6204539 VSH XPress Stainless T-piece female thread FFF 88.9x88.9xRp3/4" 6204541 VSH XPress Stainless T-piece female thread FFF 108x108xRp3/4" 6204550 VSH XPress Stainless T-piece female thread FFF 76.1x76.1xRp2" 6204561 VSH XPress Stainless T-piece female thread FFF 88.9x88.9xRp2" 6204572 VSH XPress Stainless T-piece female thread FFF 108x108xRp2" 6204759 VSH XPress Stainless straight connector FM 76.1xR2 1/2" 6204761 VSH XPress Stainless straight connector FM 88.9xR3" 6230004 VSH XPress Stainless bend 90° FF 76.1 6230015 VSH XPress Stainless bend 90° FF 88.9 6230026 VSH XPress Stainless bend 90° FF 108 6230037 VSH XPress Stainless bend 90° FØ 76.1 6230048 VSH XPress Stainless bend 90° FØ 88.9 6230059 VSH XPress Stainless bend 90° FØ 108 6230061 VSH XPress Stainless bend 45° FF 76.1 6230070 VSH XPress Stainless bend 45° FF 88.9 6230081 VSH XPress Stainless bend 45° FF 108 6230092 VSH XPress Stainless bend 45° FØ 76.1 6230103 VSH XPress Stainless bend 45° FØ 88.9 6230114 VSH XPress Stainless bend 45° FØ 108

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Plastic bodied push fit fittings for use with Shin Won Tube Co., Ltd. SWPE™ (LLDPE) tube, (not covered by the scope of this approval). Maximum working pressure 10.0 bar. Cold water use only.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

260102021

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The SWPE™ (LLDPE) tube is not covered by the scope of this approval.

Size:

¼" push fit.

Marking:

ST, Stormtec logo and size on body.

Installation Requirements:

R001 R008

Expiry date:

31/01/2031

Model:

1A2400W702: 1/4"X1/4"X1/4" STEM BRANCH TEE, 1A2100W704: 1/4"X1/4" EQUAL ELBOW (DOUBLE O-RING), 1A4100W704: 1/4"X1/4"X1/4" EQUAL TEE (DOUBLE O-RING), 1A3100W704: 1/4"X1/4" EQUAL STRAIGHT (DOUBLE O-RING), 1A5100W704: 1/4"X1/4" STEM ELBOW (DOUBLE O-RING), 1A1900W702: 1/4"X1/4"X1/4" Y-FITTING, 1A0800W702: 1/4"X1/4" BULKHEAD CONNECTOR, 1A1040W702: 1/4"X1/4" 40mm LONG ELBOW, 1A0400W702: 1/4"X1/4"X1/4" EQUAL TEE, 1A7004W000: 1/4"OD X 1/4"OD NIPPLE ELBOW, 1A1200W000: 1/4” END PLUG, 1A0200W702: 1/4”X1/4” EQUAL ELBOW, 1A0300W702: 1/4”X1/4” EQUAL STRAIGHT, 1A0500W702: 1/4”X1/4” STEM ELBOW.

Approval Holder:

Stormtec Co., Ltd.

Company Name

Stormtec Co., Ltd.

Address

143, Hwagok-ro 68gil, Gangseo Seoul 07551

Country

Korea, Republic of

General Email

info@stormtec.co.kr

View All Listings by this Company

Manufacturer:

Stormtec Co., Ltd.

Company Name

Stormtec Co., Ltd.

Address

143, Hwagok-ro 68gil, Gangseo Seoul 07551

Country

Korea, Republic of

General Email

info@stormtec.co.kr

View All Listings by this Company

Range of tapping tees with gunmetal bodies and plastic fitting, for use with SDR11 & SDR17 Polyethylene barrier pipes (manufactured to BS8588). For pipe diameters between 63mm & 90mm, the adaptor plate must be used. When used with SDR11 pipes the maximum working pressure is 16.0 bar. When used with SDR17 pipes the maximum working pressure is 10.0 bar. Cold water use, for below ground only.

Section:

1530 Miscellaneous Fittings

WRAS Approval Number:

260302023

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Because there are no accepted tests, WRAS approval of barrier pipe does not include an assessment of its ability to prevent migration of contaminants through the wall of the pipe from the surrounding soil.

Size:

Please refer to model.

Marking:

Radius systems on stem cap. Radius systems and size on metal strap.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

XR5125 Easi Fit Puriton Tapping Tee: DN63 - DN180 x 25mm Compression. XR5130 Easi Fit Puriton Tapping Tee: DN63 - DN180 x 32mm Compression.

Approval Holder:

Radius Systems Limited

Company Name

Radius Systems Limited

Address

Radius House, Berristow Lane, South Normanton, Alfreton, Derbyshire

Postcode

DE55 2JJ

Country

United Kingdom

Phone

01773582303

View All Listings by this Company

Range of cast iron (blue epoxy coated) (G versions only) or stainless steel (all other versions - F, N, R, T) vertical multistage pumps with stainless steel impellers, shaft and outer sleeve. Maximum working pressures: 16 bar, 25 bar and 40 bar. Oval flanges - Body type ‘T’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 16 bar. Round flanges - Body type ‘R’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 25 bar. Round flanges - Body type ‘F’ (1SV-3SV) - 25 bar. Round flanges - Body type ‘N’ (10SV) - 25 bar. Round flanges - Body type ‘N’ (66SV-92SV) - 16 bar. Round flanges - Body type ‘G’ (33SV, 46SV) - 40 bar. Round flanges - Body type ‘G’ (33SV, 46SV, 66SV-92SV, 125SV) - 16 bar. Round flanges - Body type ‘G’ (125SV) - 25 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260302709

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Flanged inlet and outlet: (T versions have 2 bolt oval flanges). (F, G, N, R versions have round flanges). 1SV-3SV: DN25. 5SV: DN32. 10SV: DN40. 15-22SV: DN50. 33SV: DN65. 46SV: DN80. 66SV-92SV: DN100. 125SV: DN125.

Marking:

Lowara logo, Xylem, pressure and technical data on data plate on body. Lowara and WRAS on adhesive label on body DN80 46SV_10G_055 Lowara logo, Xylem, pressure and technical data on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/03/2031

Model:

1SV, 3SV, 5SV, 10SV, 15SV, 22SV, 33SV, 46SV, 66SV, 92SV & 125SV series pumps. Example code: 10SV_05F_022_ _T/D Where: • 10 = flow rate in m³/h (1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125). • SV = series name. • _ = Motor operation. blank = standard version, H = equipped with Hydrovar, E = e-SM (1SV-22SV models only) or a single letter denoting the type of the variable speed drive model used. • 05 = 2 digits for number of impellers [05 = 5 impellers], can also be represented as: X/1A or X/2A, where X = number of impellers: 1-13, /1 or /2 = 1 or 2 impellers with outer diameter reduced. A = reduction type. • F = body type: F, T, R, G or N. 1SV-25SV models F - AISI 304, round flanges, T - AISI 304, oval flanges, R - AISI 304, discharge port above suction, round flanges, N - AISI 316, round flanges. 33-125SV models G - AISI 304/Cast Iron, round flanges. N - AISI 316, round flanges, • _ = blank (null) to denote standard version. • 022 = Rated motor power - 3 digits (kW x 10). • _ = blank (null) to denote 2-pole, 4 = 4 pole. • _ = blank (null) to denote 50Hz, 6 = 60Hz, 0 = e-SM (1SV-22SV models only). • T = Three-phase or M to denote single-phase or Null = standard version. • /D = relates to supply voltage and can also be blank, /2, /4 or /4/2.

Approval Holder:

Xylem Service Italia S.r.l

Company Name

Xylem Service Italia S.r.l

Address

Via Vittorio Lombardi 14, 36075 Montecchio Maggiore-Alte Ceccato VI, Vicenza

Country

Italy

Phone

0039 0444 707111

View All Listings by this Company

Range of electronic booster pumps with variable speed, incorporating stainless-steel bodies, impellers and shaft, EPDM gaskets and seals and an expansion vessel on the outlet. The pumps incorporate a drain port. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260304701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain port must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

PBI-L2 prefix models: 1” BSP (F) x 1” BSP (F), PBI-L4 prefix models: 1¼” BSP (F) x 1” BSP (F), PBI-L8 prefix models: 1½” BSP (F) x 1¼” BSP (F).

Marking:

Wilo, model no., date of manufacture (YYWW) and other technical information on data label on body. Wilo on control box.

Installation Requirements:

R001 R415

Expiry date:

31/03/2031

Model:

PBI-L series pumps: PBI-L203MA/P, PBI-L204MA/P, PBI-L205MA/P, PBI-L402MA/P, PBI-L403MA/P, PBI-L404MA/P, PBI-L405MA/P, PBI-L802MA/P, PBI-L803MA/P, PBI-L203EA/P, PBI-L204EA/P, PBI-L205EA/P, PBI-L402EA/P, PBI-L403EA/P, PBI-L404EA/P, PBI-L405EA/P, PBI-L802EA/P, PBI-L803EA/P, PBI-L203MA/P/S, PBI-L204MA/P/S, PBI-L205MA/P/S, PBI-L402MA/P/S, PBI-L403MA/P/S, PBI-L404MA/P/S, PBI-L405MA/P/S, PBI-L802MA/P/S, PBI-L803MA/P/S, PBI-L203EA/P/S, PBI-L204EA/P/S, PBI-L205EA/P/S, PBI-L402EA/P/S, PBI-L403EA/P/S, PBI-L404EA/P/S, PBI-L405EA/P/S, PBI-L802EA/P/S, PBI-L803EA/P/S. Where: PBI-L = series name (Electronic boosting pump variable speed pump (Inverter Pump)) 2, 4 or 8 = Rated flow capacity in m³/h. 2, 3, 4 or 5 = Number of Impellers. M or E = Power. M: 60Hz 220V/230V 1phase, E: 50Hz 220V/230V 1phase. [blank] or A = Mode. [blank]: Non-automatic models, A: Models with pressure sensor and inverter that are responsible for automatic mode, allowing the pump to operate at the corresponding RPM to maintain the set operating pressure. P = Product Category. P: Complete product. [blank] or S = Accessories. [blank]: No accessories, S: Sun cover.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Manufacturer:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Range of circulating pumps, with plastic or stainless steel (cast EN 1.4308) bodies and a plastic impeller. Maximum working pressures: Stainless steel bodied pumps 10.0 bar, Plastic bodied pumps 3.0 bar. Maximum operating temperature 95°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260307701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

R008 does not apply to the stainless-steel body models.

Size:

Composite (plastic body) (15 models): 1” BSP (M). Stainless steel body (25 models): 1½” BSP (M).

Marking:

Grundfos and Grundfos logo, type, model, production no. and other technical info on adhesive label on end of motor housing. Flow arrow on body.

Installation Requirements:

R001 R008

Expiry date:

31/03/2031

Model:

Composite (plastic body): UPM2 15-** CIL2. Stainless steel body: UPM2 25-** N130, UPM2 25-** N180, UPML 25-** N180, UPMM 25-** N180, UPMXL 25-** N180. 130 or 180 (where applicable) = port to port length in mm. ** stands for the lifting height of the pump in dm, that can be various 2 or 3 digit numbers

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of shower handsets and shower heads with (plastic bodies - various finishes) Some models incorporate a plastic flow restrictor, or a check valve with built in flow regulator (however, the complete product has not been fully tested to demonstrate it provides backflow protection) or neither (See models for FR or WSCV). Maximum operating temperature 60.0°C Open outlet use only

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

260302015

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2" BSP (M) – Shower handsets 13.90mm ID – Showerheads

Marking:

SOLEX on body

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

Shower Handsets: P96400-1-XX (FR) P96400-2-XX (WSCV) P96400-1-white (FR, chrome finish, white faceplate) P96400-2-white (WSCV, chrome finish, white faceplate) Shower Heads: P100300-1-XX (FR) P100300-2-XX (No FR or WSCV) P100300-1-white (With FR, chrome finish, white faceplate) P103000-2-white (No FR or WSCV, chrome finish, white faceplate) P100400-1-XX (With FR) P100400-2-XX (No FR or WSCV) P100400-1-white (With FR, chrome finish, white faceplate) P100400-2-white (No FR or WSCV, chrome finish, white faceplate) Where XX denotes the finish (for both hand showers and showerheads unless otherwise stated) and can be replaced with any of the following KI: Chrome KF: Matt Black DA: Warm sunset GL: Cool Sunrise DL: Brushed warm sunset DC: Super steel AL: Brushed Graphite GN: Brushed cool sunrise MS0: Satin Steel (showerhead only) MG0: Satin Graphite (showerhead only)

Approval Holder:

Xiamen Solex High-Tech Industries Co., Ltd.

Company Name

Xiamen Solex High-Tech Industries Co., Ltd.

Address

No. 298 Yangguang Road West, Haicang District, Xiamen, Fujian Province, 361022

Country

China

General Email

brian_lin@mysolex.com

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Undefinable Air Gap – See IRN’s

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

31/03/2031

Notes & Further Information

Fixed Head in 4 different colours - Chrome, Matt Black, Brushed Brass and Gunmetal Grey AQ = Aqualisa XX = AA , AD , AJ , AH AQAA - Chrome AQAD - Matt Black AQAJ - Gunmetal Grey AQAH - Brushed Brass

Approval Holder:

Aqualisa Products Ltd.

Company Name

Aqualisa Products Ltd.

Address

Unit 6 The Flyers Way, Westerham, Kent

Postcode

TN6 1DE

Phone

07920 790367

General Email

tracey.jones@aqualisa.co.uk

View All Listings by this Company

Manufacturers:

Xiamen Solex High-Tech Industries Co.,Ltd

Section:

1825 Showers

Description:

A Range of Self closing shower(s)

Wall mounted. Undefinable Air Gap – See IRN’s. Incorporates a check valve cartridge (however the complete assembly has not been fully tested to demonstrate it provides backflow protection). Supplied with other components: Isolation valves.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

31/03/2031

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined flexible hose assemblies with DZR brass end connections. Some models incorporate spherical valves. Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

260488001

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model

Marking:

BFFTC…. Codes = MSL, WRAS, YYYY Date of manufacture CFTC……. Codes = MB, WRAS, YYYY Date of manufacture

Installation Requirements:

R001

Expiry date:

30/04/2031

Model:

BFFTCW-XXXXX BFFTCWIV-XXXXXX CMFTCW-XXXXXXX CMFTCWIV-XXXXXX BFFTCW-XXXXXX = Flexi Tap Connector WRAS – MSL Branded BFFTCWIV-XXXXXX = Flexi Tap Connector WRAS Iso Valve – MSL Branded CMFTCW-XXXXXX = Flexi Tap Connector WRAS – MB Branded CMFTCWIV-XXXXXX = Flexi Tap Connector WRAS Iso Valve – MB Branded 10 = 10mm, 12 = 12mm, 15 = 15mm, 22 = 22mm D = ½”, E = ¾” 150 = 150mm, 300 = 300mm, 500 = 500mm, 900 = 900mm To be used with copper tube manufactured to EN1057. To use the WRAS default value of torque.

Product Images

Approval Holder:

Navigator MSL Ltd.

Company Name

Navigator MSL Ltd.

Address

Mill Road, Sharnbrook, Beds.

Postcode

MK44 1NP

Phone

01234 781234

General Email

sales@navigatormsl.com

View All Listings by this Company

Ranges of free standing stainless steel cylinders. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C

Section:

1890 Unvented Heating Apparatus

WRAS Approval Number:

241104719

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

No safety kit supplied.

Size:

G½” BSP (F), G¾” BSP (F), G1” BSP (F), G1.2” BSP (F), G1.5” BSP (F), G2” BSP (F)

Marking:

Hisa Logo on body. Product info on data label.

Installation Requirements:

R001 R140 R360

Expiry date:

30/11/2029

Model:

HPT-150L, HPT-200L, HPT-300L, HPTB-150/50L, HPTB-200/50L

Approval Holder:

Hisa Engineering Ltd

Company Name

Hisa Engineering Ltd

Address

396, Hillington Road Glasgow

Postcode

G52 4BL

Country

United Kingdom

General Email

jay@hisauk.com

View All Listings by this Company

Range of 2, 3 or 4 way manifolds with brass bodies and stop valves at each of the outlets. Maximum operating pressure 10 bar. Maximum operating temperature 85°C

Section:

1950 Manifolds

Section Subtitle:

Metal.

WRAS Approval Number:

260304704

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See below

Marking:

Savar Brass SRL and size on body

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

Manifolds ¾” x ½” BSP (F/M): 1102 W034 - 2 way, 1103 W034 - 3 way, 1104 W034 - 4way. Manifolds ¾” x ¾” BSP (F/M): 1202 W034 - 2 way, 1203 W034 - 3 way, 1204 W034 - 4 way. End Caps (for unused outlets): 1530 M034 – ¾” BSP (M), 1532 F034 – ¾” BSP (F).

Approval Holder:

Savar Brass Srl

Company Name

Savar Brass Srl

Address

Via Fratelli Capponi, 88-90 25068 Sarezzo (Bs) Italy

View All Listings by this Company

Section:

2010 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control

Wall Mounted Concealed. Inlets incorporate approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R020

Expiry date:

30/06/2030

Model:

FRM SHCDIV C FRM SHCDIV BLK FRM SHCDIV GM FRM SHCDIV BB

Notes & Further Information

Model added February 2026: RP3 SAI SHCDIV C

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of wafer or lugged (see models) butterfly valves incorporating blue epoxy coated ductile iron bodies and discs, with Maximum working pressure: 16 Bar. Maximum operating temperature: 100 °C.

Section:

2020 Valves

Section Subtitle:

Butterfly.

WRAS Approval Number:

260302019

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN40 to DN300 Flange connections (see models).

Marking:

OMAL, model, body material and disc material on plate on body. DN and PN on body.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

V8xxXM068 (DN40) V8xxXM069 (DN50) V8xxXM070 (DN65) V8xxXM071 (DN80) V8xxXM072 (DN100) V8xxXM073 (DN125) V8xxXM074 (DN150) V8xxXM075 (DN200) V8xxXM076 (DN250) V8xxXM077 (DN300) Where xx denotes lugged or wafer, and can be replaced with either of the following: 76 = Wafer, 86 = Lugged.

Approval Holder:

OMAL SPA SB

Company Name

OMAL SPA SB

Address

Via Ponte Nuovo, 11 – 25050 Rodengo Saiano – BS – Italy

View All Listings by this Company

Range of spherical valves with nickel-plated brass bodies, chrome plated brass balls, PTFE seat (SD3009 only) and NBR ‘O’-rings. The SD3009 models are screw-driver operated, the SD6011 model incorporate a short lever operating member. The compression connections are for use with copper pipes (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

2260 Valves

Section Subtitle:

Spherical, metal.

WRAS Approval Number:

260315005

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

SD3009: 22mm compression, SD6011: 15mm compression x ¾” BSP (M).

Marking:

SD, production date (MM-YY) and flow arrow on body. SD and size on nut. Size also marked on body of SD3009.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

SD3009 - Isolation valve, SD6011 - Washing machine valve.

Approval Holder:

Yuhuan General Ball Valve Factory Co., Ltd.

Company Name

Yuhuan General Ball Valve Factory Co., Ltd.

Address

Yungang Village Chumen Town Yuhuan Zhejiang

Postcode

317605

Country

China

View All Listings by this Company

Range of resilient seated gate valves with blue epoxy coated ductile iron body and an EPDM coated ductile iron wedge. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.

Section:

2290 Valves

Section Subtitle:

Stop, gate, metal.

WRAS Approval Number:

260304005

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models

Marking:

DN size, PN rating, Brand logo, and BS 5163 on body.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

CV-R101(N2): DN50, DN80, DN100, DN150, DN200, DN250, DN300 flanged. CV-R101L: DN350, DN400, DN450, DN500, DN600 flanged.

Approval Holder:

Shanghai Johnson Valve Industries Co Ltd

Company Name

Shanghai Johnson Valve Industries Co Ltd

Address

Suite 2511, Tower 3, 166 Minhong Road, Shanghai 201102, P.R.China

View All Listings by this Company

'Novus 30'. Orange coloured, nitrile rubber/aramid fibre gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

260355027

Expiry date:

31/03/2031

Approval Holder:

Flexitallic UK Ltd.

Company Name

Flexitallic UK Ltd.

Address

Scandinavia Mill, Hunsworth Lane, Cleckheaton, West Yorks.

Postcode

BD19 4LN

Phone

+44 1274 851 273

General Email

uksales@flexitallic.com

View All Listings by this Company

'BADAMID A70 GF30 HE WL BLACK'. Black coloured, injection moulded, glass fibre ranforced PA66 material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

260355020

Expiry date:

31/03/2031

Approval Holder:

Bada Hispanaplast S.A.

Company Name

Bada Hispanaplast S.A.

Address

Ronda Industria 153, Poligono Industrial Sepes, 22006 Huesca

Country

Spain

View All Listings by this Company

'Ryton XE7730BL'. Black coloured, injection moulded PPSU material. For use with water up to 85°C.

Section:

5256 Polyphenylsulfone

Expiry date:

31/08/2030

Approval Holder:

Solvay Specialty Polymers USA, LLC

Company Name

Solvay Specialty Polymers USA, LLC

Address

4500 McGinnis Ferry Road Alpharetta GA 30005-3914

Country

USA

Phone

+1 770 772 8200

General Email

SpecialtyPolymers.Americas@solvay.com

View All Listings by this Company

'SQ-30T-W, SQ-40T-W, SQ-50T-W, SQ-60T-W, SQ-70T-W, SQ-80T-W, & SQ-90T-W (transparent, unpigmented)'. ‘SQ-30R-W, SQ-40R-W, SQ-50R-W, SQ-60R-W, SQ-70R-W, SQ-80R-W, & SQ-90R-W (red coloured)'. ‘SQ-30B-W, SQ-40B-W, SQ-50B-W, SQ-60B-W, SQ-70B-W, SQ-80B-W, & SQ-90B (blue coloured)'. Range of compression moulded, silicone rubber materials. Shore hardness between 30 & 90. Tested in-radius size 0.9mm. For use with water up to 85°C:

Section:

5415 Rubbers

Section Subtitle:

Silicone - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

260255017

Expiry date:

28/02/2031

Approval Holder:

Hun-Yi Rubber Industrial Co., Ltd.

Company Name

Hun-Yi Rubber Industrial Co., Ltd.

Address

No. 40, Lane 193, Hochen Road, Homei Town, Changhua County

Country

Taiwan,

Phone

+(886)47551315

General Email

hunyirubber@yahoo.com.tw

View All Listings by this Company

'PVC Tube Settler Media FS42.50'. Black coloured, extruded PVC 'tube settler' component. For use with water up to 30°C.

Section:

5301 Polyvinylchloride (PVC, PVC-U and CPVC)

Section Subtitle:

Components.

WRAS Approval Number:

260355017

Expiry date:

31/03/2031

Approval Holder:

MM Aqua Technologies Ltd.

Company Name

MM Aqua Technologies Ltd.

Address

Behrampura Road, Khansda, Gurugram, Haryana - 122001

Country

India

View All Listings by this Company