Range of polypropylene push-fit fittings. The 20, 25 and 32mm sizes are for use with MDPE Pipe (manufactured to BS EN 12201-2). The 15, 22 and 28mm connections are for use with the following pipes: PEX (manufactured to BS 7291-3) for 15, 22 and 28mm sizes. PB (manufactured to BS 7291-2) and Copper (manufactured to BS EN 1057) for 15 and 22mm sizes only. Maximum working pressures: UG601B model: 16.0 bar. All other models: 12.5 bar. Cold water use only.
Range of brass press fittings with EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
“>B<Press NZ” range of press fittings incorporating copper (EN12165 CW024A) or copper alloy (CC499K-DW) bodies. For use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of under counter, vented, electric instantaneous (near boiling) water heaters with a stainless steel tank and silicone seals. Maximum operating temperature 98°C.
Range of water meter measuring capsules with brass bodies. Maximum working pressure 16.0 bar. Please refer to model for maximum operating temperature.
Range of high flow water meters with black epoxy coated ductile iron bodies and EPDM gaskets. Maximum working pressure; 16 Bar Maximum operating temperature Cold water only
Range of water meters with a brass body and plastic strainer on the inlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C
Range of electromagnetic flow meters with stainless steel bodies, EPDM inner liner and SUS316L electrodes. Maximum working pressure 16 Bar. Maximum operating temperature 40°C.
Range of pump docking manifolds with plastic bodies. Maximum working pressure: 5.5 bar. Cold water only.
‘Hansen True Fit’ range of black coloured, plastic threaded fittings. Maximum working pressure 1/8” – 2” BSP: 16.0bar, 2½” BSP: 12.0bar, 3” – 4”: 10.0bar. Cold water and above ground use only.
Range of in-line flow sensors incorporating either brass (type 230, 235 & 236) or plastic (type 200 & 210) bodies & EPDM ‘O’-rings. Maximum working pressure 12.0 Bar Maximum operating temperature 100.0°C
Range of multistage pumps with stainless steel bodies Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 51OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52CS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52DS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 52OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OS-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 62OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6301-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6302-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6303-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 63OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 6300-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OS-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 42OH-** | Various | G3/8(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator | ||
| 53OH-** | Various | G1/2(M) | open outlet bar | 65 °C | KAIPING BOYU | BODY | No | Not applicable | Aerator |
** Representative all models are available with the following finish code: CP-Polished Chrome BN-Brushed Nickel MB-Matte Black ORB-Oil Rubber Bronze PB-Polished Brass WP-Weathered Pewter BB-Brushed Brass
Range of overhead shower outlets with (stainless steel bodies - various finishes). The inlet incorporates a combined EPDM washer and an approved check valve cartridge: however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: Open outlet use only. Maximum operating temperature 65.0°C
Range of shower handsets with (plastic bodies - various finishes), incorporating an approved single check valve cartridge on the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure: Open outlet use only Maximum operating temperature: 60°C.
Range of shower handsets with chromium plated plastic bodies. Maximum operating temperature 65.0°C Open outlet use only
Shower handsets with chromium plated plastic bodies and a plastic flow regulator in the inlet. Maximum operating temperature 65°C. Open outlet use only.
Range of wall or ceiling mounted shower arms with brass bodies (various finishes). Maximum operating temperature 65°C. Open outlet use only.
Range of shower handsets with brass body available in various finishes. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with bronze bodies and a stainless steel mesh strainer. Maximum working pressure 20 bar. Maximum operating temperature 85°C
Range of DZR brass and brass bodied in-line Y-Stainers with a stainless-steel mesh. Compression models for use with copper pipe to BS EN1057. Maximum working pressure 10 Bar Maximum operating temperature 60°C.
Range of self-closing taps (chromium plated brass) incorporating a push button headwork with a dome type operating member. The inlet hoses each incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Range of self-closing taps (chromium plated brass) with a dome type operating member. The spout outlet incorporates a plastic aerator. Model 02 122 06 99 model is supplied with a metal backnut. Maximum working pressure 10 bar. Maximum operating temperature 65C
‘TAQ PEX’ range of PEX lined flexible hose assemblies with either stainless steel braiding or grey polymeric (PET - Polyethylene terephthalate) braiding. G3/8" captive nut connection includes an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Hoses with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless steel, interlocked shower hoses with EPDM liner and O-rings. Open outlet use only. Maximum operating temperature 65°C.
Range of stainless-steel braided, EPDM lined flexible hose assemblies. The captive nut end connections incorporate a washer, the M10 connection incorporates an ‘O’-ring. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Excelsior Range of Direct and indirect unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C. The product is supplied with an inlet control group (safety kit) consisting of a pressure reducing valve pre-set at 3.0 bar, strainer, an expansion relief valve set at 6.0 bar and a check valve cartridge (verified by test - suitable for backflow protection against Fluid Category 2). A tundish and expansion vessel are also provided Maximum working pressure: 5.5 Bar (All Circuits) Maximum operating temperature 90.0°C
Range of unvented heat pump storage cylinders which consist of an air-source heat pump sitting on top of the tank with either no internal coil (model numbers ending without S) or a factory fitted single internal coil (model numbers ending with S). The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar @ 90˚C and an stainless steel immersion heater and titanium alloy anode. The product is not supplied with an inlet control group (safety kit). Maximum operating temperature 70°C. Maximum working pressure (primary & secondary circuit) 5.5 bar.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 71 681 xx0 | Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish | G 1/2 (offset) | 10 bar | 70 °C | hansgrohe | on the handle | Yes | Ceramic cartridge | Not Applicable |
Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 86005640 | Chrome | 15mm compression joint | 10 bar | 80 °C | TRITON,86005640 | Handle/ body | No | Ceramic cartridge |
Wall mounted, concealed shower valve (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever operating members and a manual diverter to shower outlets with a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of wall mounted, manually operated, concealed shower valves (stainless steel bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure: 5.0 bar. Maximum operating temperature: 60°C.
Wall Mounted shower valve with shower hand-set, hose with riser rail and overhead shower, available in various finishes. A05846 incorporates a single sequential headwork, all other models incorporate 1/4 turn ceramic disc headwork. Some model include a flow regulator. Models A5846 & A05847 maximum pressure 10.0 bar. All other models maximum pressure 5.0 bar Maximum temperature all models 65°C
Range of T type thermostatic blending valves with (brass bodies - chrome plated finishes). The inlets incorporate a stainless-steel strainer. For use with copper pipe (BS EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valves (chromium plated brass) incorporating a ceramic disc diverter (models SD4373-2S) with various operating members. A quarter turn ceramic disc headwork (models SH40001-2, SD4373S) or 2 quarter turn ceramic disc headworks (model SH40001). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate backflow protection. Models SH40001-2, SH40001 incorporate stainless steel strainers. Supplied with a shower hose, shower handset, riser rail & overhead shower outlet (models SD4373-2S, SH40001). SD4373S incorporates a shower hose, shower handset & riser rail. SH40001-2 incorporates an overhead shower outlet Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C. Model SH40001 Maximum operating temperature 60°C
Wall mounted, concealed, thermostatic blending valve incorporating a thermostatic cartridge with a dome operating member and supplied with a trim set. Each inlet incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of butterfly valves with blue epoxy coated, ductile iron bodies and either blue epoxy coated ductile iron or stainless-steel discs and EPDM seats and ‘O’-rings. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C
Range of butterfly valves with blue epoxy coated ductile iron bodies, ductile iron or stainless steel discs with EPDM seats and a lever operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Combined temperature and pressure relief valves with a DZR brass body, pre-set at 7.0, 10.0 or 15.0 bar. Maximum working pressure See models Maximum operating temperature 90.0°C
Combined temperature and pressure relief valves pre-set at 7.0 or 10.0 bar (See models) with a DZR brass body. The valves incorporate lever easing gear. Maximum working pressure: See models. Maximum operating temperature 85.0°C
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure: 11.0 Bar (model O2010.G15) and 9.0 Bar (model O2010.G20). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure: 11.0 Bar (model O1011.G15) and 9.0 Bar (model O1011.G20). Cold water use only.
Range of pilot operated flow control valves with blue epoxy coated ductile Iron bodies and EPDM ‘O’-rings. Auxiliary components include stainless steel tube with fittings and ball valves. Maximum working pressure 16.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet, manually operated flow control valve (brass body) incorporating a quarter turn ceramic disc headwork. Maximum working pressure:10BAR Maximum working temperature:65°c
In-line, manually adjustable pressure reducing valve with brushed chrome plated DZR brass body, for use with copper pipe (manufactured to BS EN 1057). Supplied with a pressure gauge. Maximum inlet supply pressure 16.0 bar. Maximum outlet pressures between 1.0 and 6.0 bar. Maximum operating temperature 85°C.
Range of DZR brass and nickel plated DZR brass pressure reducing valves with a pressure gauge connection. Compression connection to be used with copper pipe EN1057. Outlet pressures adjustable between 1.5 & 7.0 bar (pre-set at 3.0 bar). Maximum working pressure 16.0 bar. Maximum operating temperature of 85°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies, Stainless-steel filter, EPDM ‘O’-rings and diaphragm. The valves have an adjustable pressure reducing facility controlled via a pilot valve (see note), with auxiliary components including stainless-steel tubing and fittings, strainer and stainless-steel spherical valves. Maximum working pressure 16.0 Bar. Maximum operating temperature 60°C.
Range of normally closed (L182 models) solenoid valves with brass bodies. Maximum working pressure 16.0 bar: 12900 Maximum working pressure 12.0 bar: 12903 & 12906 Maximum working pressure 10.0 bar: 12909 ,12912 & 12915 Maximum operating temperature 85.0°C
Range of bistable solenoid valves incorporating a plastic body, EPDM diaphragm and ‘O’-rings. The 51.005.101 model incorporates a stainless-steel strainer on the inlet. Maximum operating pressures: 51.005.100: 5.0 bar, 51.005.101: 10.0 bar. Maximum operating temperature 70°C.
Page 193 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
