Range of in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.
Range of water meters with brass bodies, plastic turbines and plastic strainers on inlets. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Hydraulic circuit used to control the water path within the heating and sanitary boiler, with plastic body incorporating filter, flow regulator, plate heat exchanger and EPDM O-rings. Maximum working pressure 7.0 bar. Maximum operating temperature 85°C.
Concealed, floor mounted basic set with DZR brass body. For use with floor standing combination tap assemblies. Maximum operating pressure 10 bar. Maximum operating temperature 70°C
‘Monsoon Standard’ range of single and twin ended shower booster pumps with brass bodies, brass impellers, EPDM seals and NBR ‘O’-rings. The inlet(s) of the pump body incorporate(s) a plastic strainer. Models with push fit connections include an integral isolation valve. Pushfit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
Range of horizontal or vertical multi-stage pumps with a stainless-steel body (HM models) or cast iron body with blue coloured cationic resin coating (VM models), incorporating either plastic or stainless-steel impellers (see model), stainless steel sleeve, EPDM gaskets and seals. Maximum working pressure 10.0 bar / 16.0 bar (see models). Cold water use only.
Range of single or twin shower pumps with brass bodies, brass impeller supplied with flexible connection hoses that incorporate servicing valves. Maximum Working pressure 6 Bar Maximum operating temperature 65°C
‘Hydro MPC’ range of booster sets incorporating vertical multistage centrifugal pumps, butterfly valves, non-return valves (not suitable for backflow protection), pressure transmitters, pressure gauges, lever operated spherical valves, stainless steel blanking flanges and fibre/NBR gaskets. Maximum working pressure 16.0 bar. Cold water use only. ‘Hydro MPC’ range of booster sets incorporating vertical multistage centrifugal pumps, butterfly valves, non-return valves (not suitable for backflow protection), pressure transmitters, pressure gauges, lever operated spherical valves, stainless steel blanking flanges and fibre/NBR gaskets. Maximum working pressure 16.0 bar. Cold water use only.
Concealed, wall mounted elbow fitting with a brass body incorporating EDPM `O`-rings. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 70.0°C.
Range of in-line Y patterned strainers with flanged ductile iron bodies (blue epoxy coated) and stainless-steel mesh strainers. The strainers also incorporate a drain plug. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line Y patterned strainers with flanged ductile iron bodies (blue epoxy coated) and stainless-steel mesh strainers. The strainers also incorporate a drain plug. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass body and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain taps with brass or DZR brass body (some models chrome plated) and rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of drain valves with a brass bodies, spindle and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Self-closing combination tap assembly (chromium plated brass) with a spring-loaded headwork controlling both temperature and flow with a dome type operating member. The spout outlet incorporates a plastic flow straightener. The flexible hose inlets incorporate a combined EPDM washer and stainless-steel strainer, as well as an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of stainless-steel braided TPS lined flexible hose assemblies incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves Push-fit fittings for use with: Copper Pipes manufactured in accordance with BS EN 1057 PB pipes manufactured in accordance with BS 7291-2 PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure 12.0 bar. Maximum operating temperature 65°C.
‘Qualflex Excel’ range of stainless steel over braided, PEX lined flexible hoses, incorporating EPDM or fibre washers. The products can be supplied with a range of end connections and seals. Some models also incorporate integral isolation valves. Push-fit fittings for use for with: Copper Pipes manufactured in accordance with BS EN 1057 Plastic PB pipes manufactured in accordance with BS 7291-2 Plastic PEX pipes manufactured in accordance with BS 7291-3 Maximum working pressure: 6.0 bar. Maximum operating temperature: 65°C.
Range of multilayer PVC hoses. Maximum operating temperature 65°C. Open outlet use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel braided, EPDM lined flexible hose assemblies with a variety of end connections (see models for full breakdown), including EPDM washers and ‘O’-rings where applicable. Some models are supplied with screwdriver operated isolation valves (see model list). All compression and push-fit fittings are to be used with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16 bar. Maximum operating temperature: 85°C.
Range of Indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 90˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check cartridge, verified by test (suitable for backflow protection against fluid category 2) an expansion vessel and tundish. Maximum working pressure: Secondary: 4.0 Bar Primary: 3.0 Maximum operating temperature 99.0°C
Range of primary hot water buffer tanks consisting of stainless steel shells. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of primary hot water buffer tanks consisting of insulated enamel and Stainless steel shells. Maximum working pressure 8.0 bar. Maximum operating temperature 80°C.
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection). Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Also supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 95˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with an expansion vessel and tundish. Maximum working pressures: Secondary circuit: 4.0 Bar Primary Circuit: 3.0 Bar Solar circuit: 6.0 Bar Maximum operating temperature 99.0°C
Range of air venting valves incorporating an epoxy coated, iron body and a drain point. Maximum working pressure 16.0 bar. Maximum operating temperature 60˚C.
‘Rada’ electronically controlled thermostatic blending valve, with a stainless-steel body, EPDM ‘o’ rings and seals. Maximum working pressure; 13.8 Bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted thermostatic bar shower mixers, (chrome plated brass bodies), incorporating a ceramic disc diverter cartridge controlling the flow with a dome type operating member. The temperature is controlled independently with a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate stainless steel strainer washers, approved single check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and screwdriver operated isolation valves. The products are supplied with a shower hose, handset, riser rail assembly and an overhead shower outlet. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted thermostatic blending shower valves (brass bodies – various finishes) incorporating quarter turn ceramic disc two-way diverter headwork controlling the flow with dome or square type operating members. Temperature is controlled independently via a thermostatic cartridge incorporating a manual override button with dome or square type operating members. The inlets incorporate a stainless-steel strainer and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure; 5 Bar Maximum operating temperature 60°C
Range of wafer and fully lugged butterfly valves with a blue epoxy coated cast iron bodies, EPDM seat and a stainless steel or chrome plated iron disc. Products are either handwheel or gear operated. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated, ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Fire hydrant (screw down pattern type) with ductile iron body (blue epoxy coated). Maximum working pressure 16.0 bar. For above and below ground, cold-water use.
Range of fire hydrants with an epoxy coated, cast iron body, operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Range of fire hydrants with an epoxy coated, cast iron body, operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C
Fire hydrant with a ductile iron body (blue epoxy powder coated) operated via a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of regulating and shut-off valves with brass bodies and EPDM ‘O’-Rings. Maximum working pressure 16.0 Bar for BSP (M) and 25.0 bar for BSP (F). Maximum operating temperature 85.0°C
Range of swing gate, non-return valves with (blue or red epoxy powder coated) ductile iron bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wafer or globe type spring loaded, resilient trim, non-return valves with cast iron bodies (blue epoxy powder coated). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line, manually adjustable pressure reducing valves with blue epoxy coated ductile iron bodies and EPDM gaskets and ‘O’-rings (all models) and an EPDM diaphragm. Outlet pressure range: 1.5 - 6.0 bar. Maximum supply pressure 16.0 bar. Cold water use only.
Range of in-line, manually adjustable pressure reducing valves with nickel plated DZR brass body. Maximum inlet supply pressure 25 bar. Maximum operating temperature 80°C
Range of angled pressure relief valves (pre-set at various pressures) with DZR brass bodies and EPDM diaphragms. Maximum working pressure: SEE MODELS Maximum operating temperature 99.0°C
Range of lever, handle or square operated (see models) spherical valves with brass bodies, incorporating PTFE seats and a brass ball with a red coating. Maximum working pressure 40.0 Bar Maximum operating temperature 95.0°C
Range of spherical valves incorporating nickel plated (brass bodies with chrome plated brass ball and operated via lever, handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
A range of screwdriver operated spherical valves with brass bodies and brass ball, EDPM ‘O’-rings and fibre washers. Maximum working pressure 16.0 bar, Maximum working temperature 85°C.
Range of spherical valves incorporating DZR brass body, plastic ball and lever type operating members. The products also incorporate a drain valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of spherical valves incorporating nickel plated brass bodies with chrome plated brass ball and operated via lever, butterfly type handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10130420) Maximum working pressure 25.0 bar (model 10130379) Maximum working pressure 40.0 bar (models 10130277 & 10130345) Maximum operating temperature 85°C.
Page 15 of 19
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
