Range of pillar taps (chromium plated brass) incorporating non-rising spindle headwork with cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 7.0 bar. Maximum operating temperature 65°C.
Range of wall mounted, thermostatic shower valves with chromium plated brass body. Flow is controlled by a quarter turn ceramic disc headwork with single lever operating members. Temperature is controlled by a thermostatic cartridge with a dome type operating member which incorporates a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
‘CB ISR’ range of capillary fittings with internal solder rings, DZR brass or gunmetal capillary, lead free solder ring and threaded fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum working temperatures 99°C.
Range of non verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. The products incorporate a drain port between the cartridges. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet can incorporate either a plastic flow straightener or a plastic aerator. When supplied with a plastic flow straightener there is a combined EPDM washer and stainless steel strainer behind it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
'581189 Center Jet Blue Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
Wall mounted bar type thermostatic mixing valve (chromium plated brass) incorporating a ¼ turn ceramic disc headwork controlling the flow with a dome type operating member and a secondary ceramic disc headwork diverting the flow between the overhead shower and hand shower with a single lever operating member. The temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. Both inlets incorporate single check valve cartridges, however, the complete assembly has not been tested to demonstrate it provides backflow protection. The product is supplied with a fixed overhead shower, shower handset and hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
'Center Soldering Flux Paste'. White coloured paste flux. For use with water up to 85°C.
Two hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightner. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Center Brand range of brass and copper end feed fittings for use with copper pipe. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of plastic shower hoses (chrome effect finish) incorporating a PVC inner liner, with EPDM ‘O’-rings and/or washers. Maximum operating temperature 60°C.
Range of pressure reducing valves with DZR brass bodies, integral stainless steel strainer, and EPDM ‘O’-rings and membrane. The oulet pressure is adjustable between 1.5 bar and 6.0 bar. Maximum inlet supply pressure 25.0 bar. Maximum operating temperature 70°C.
A range of wall mounted self-closing pillar taps or shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. The spout outlet incorporates a plastic aerator Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of deck mounted self-closing pillar taps (chromium plated brass), incorporating a spring-loaded headwork with a dome type operating member. The spout outlet incorporates a plastic flow straightener. During January and February 2022, the products are supplied with metal back nuts. From March 2022, the products are supplied with plastic backnuts. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
A range of wall mounted self-closing pillar taps or shower valves (chromium plated brass), incorporating a spring loaded headwork with a dome type operating member. T Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Range of wafer or lugged butterfly valves incorporating blue epoxy coated ductile iron bodies, EPDM seats and stainless steel or ductile iron discs (nickel plated). The products are supplied with either bare shaft or with lever or gear operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of water meters with blue epoxy coated iron bodies and EPDM ‘O’-rings. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes). Model A05406 has a non-rising spindle headwork with cross top operating members. All other models have a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies, incorporating brass bodies (various finishes), ceramic cartridge headwork with a single lever operating member and waterfall spout outlet. The waterfall spout outlets of models A05421, A05422 & A05418 incorporate a stainless-steel mesh. Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with either cross top (A05434 model only) or single lever operating members. The spout outlets incorporate a plastic flow straightener or a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset and metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks with either single lever, dome or cross-top operating members. The spout outlets incorporate plastic aerators or flow straighteners with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
CB (CENTRE) Range of end feed copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
CB Range of solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of end feed brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of expansion vessels with butyl membranes. Maximum working pressure 8.0, 10.0, 16.0 or 20.0 bar (please refer to model). Maximum operating temperature 70 or 100°C (please refer to model).
Range of non-rising spindle headworks (cast brass body) with EPDM ‘O’-rings and seat washer. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
'F15220 Center Silicone Lubricant'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
Centerstore ranges of Direct, Indirect, Solar Single, Solar Twin, Slim Direct and Slim Indirect stainless steel insulated unvented hot water storage cylinders with external expansion. The DHW circuit consists of a temperature and pressure relief valve set at 7.0 bar and 90°C, an inlet control group consisting of a pressure reducing valve adjustable between 2.7 and 3.3 bar, an expansion relief valve (SRV) set at 6.0 bar, a strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) also supplied with a tundish. Maximum supply pressure to the inlet control group 10.0 bar. Maximum working pressures - Primary circuit 6.0 bar, Secondary circuit 5.5 bar. Maximum operating temperature 65˚C.
Range of CENTERSTORE AIR bubble top indirect and direct single coil unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 10.0 bar@90˚C. A safety kit (manifold) consisting of a single check valve assembly, verified by test (suitable for backflow prevention against fluid category 2), strainer, an expansion relief valve set at 8.0 bar and a pressure reducing valve set at 3.0 bar and a tundish is also provided. Alternative inlet control group and temperature and pressure relief valve added March 2023. Maximum working pressure: Secondary circuit: 7.5 bar. Primary circuit: 6.0 bar. Maximum operating temperature 65°C.
Range of spherical valves with brass (K65281, K65282, K65283, K65301, K65302, K65303, K65291, K65292, K65293, K65311, K65312 & K65313) or DZR brass (K64783, K64784, K64793, K64794, K64763, K64764, K64773, K64774) bodies (chrome plated, nickel plated or without plating - see model), chrome plated brass ball and a range of different operating members (see model). Compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of twin shower booster pumps with plastic bodies and impellers. The pump body inlet incorporates a combined EPDM washer and stainless steel strainer. Maximum working pressure: D01695 model 1.5 bar D01696 model 2.0 bar. Maximum operating temperature 65°C
Pillar taps (chromium plated brass) incorporating non-rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes - see model), incorporating ¼ turn ceramic disc headworks with single lever operating members. The spout outlet can either incorporate a plastic aerator with an NBR washer or plastic flow straightener with a combined NBR washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet are pull-out spray type, which incorporates aerators and approved single check valve cartridges, however the complete assemblies have not been tested to demonstrate backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 65.°C
Range of magnetic, electrolytic or combined magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
CB Ranges of brass, DZR brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe to BS EN 1057.
CB ranges of brass, chromium plated brass, nickel plated brass and DZR brass compression fittings for use with copper pipe (manufactured to to BS EN1057:2006 + A1:2010). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of two hole, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating quarter turn ceramic disk headworks with single lever operating members. The spout outlet incorporates a stainless steel strainer and a plastic flow straightener.
Non-metallic materials and components comply with BS6920 at 65°C
Range of pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (Models A05017, A05018, A05490 & A05491) or a plastic aerator (Models A05029 & A05030). The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C for all models except A05490 & A05491 which are 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating ceramic cartridge headworks or ceramic disk headworks (model A05021) with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model A05022 is only supplied with an aerator) . The products are supplied with a click type pop-up waste. A05021 and A05494 maximum working pressure 10.0 bar. A05022, A05025 and A05495 maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Filling loop assemblies consisting of a stainless steel braided EPDM lined flexible hose, an isolation valve and another isolation valve incorporating a non-verifiable double check valve assembly, verified by test (suitable for backflow protection against fluid category 3). The 171293 model is supplied with an isolation valve including a dial type pressure gauge. The 171292 model is also supplied with brass end caps incorporating EPDM washers. For use with coper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of end feed copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Jet 806’ range of pre-set pressure relief valves incorporating gunmetal bodies, PTFE seat and lever operated easing gear. Each valve is available with a pre-set rating of between 1.0 bar and 12.5 bar, in increments of 0.1 bar. Maximum operating temperature 95˚C.
Two hole, single outlet (fixed) combination tap assembly (chrome plated brass body), Incorporating non-rising spindle headworks with dome type top operating members. The product incorporates a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with dome type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Dual flush, WC outlet valves. The valves are operated via a push button assembly for either full or reduced flush and incorporate an internal overflow. Cold water use only.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
'571983 & 571984'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
Range of shower rail kits, (chrome plated - plastic bodies) incorporating a shower handset, shower hose and adjustable shower rail. Maximum operating temperature 80°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 80°C
Side entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic disc headworks with single lever operating members (see models). The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.
Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of quarter turn, lever handle operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies. Fittings incorporate EPDM seat washers and PTFE seals. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of manually operated dual flush WC outlet valves. Cold water use only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporate a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65˚C.
Range of wall mounted, thermostatic bar shower mixer (chrome plated brass body), incorporating a quarter turn ceramic disc headwork that controls the flow with a dome operating member. Temperature is controlled independently via a thermostatic cartridge with dome type operating member that incorporates a manual override button. Both inlets incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. This product is supplied with an overhead shower, handset, shower hose and a riser rail assembly that incorporates a manual diverter that controls flow from overhead shower and shower handset. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of shock arrestors with stainless steel bodies and EPDM diaphragm. Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of pillar taps, (chrome plated brass bodies) incorporating non-rising spindle headworks with dome or cross-top type operating members. Model (C58118) incorporate quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two-hole, single outlet, fixed combination tap assembly (chrome plated brass body) incorporating non-rising spindle headworks with a dome type operating members. The spout outlet incorporate a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating a non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Product is supplied with a lever operated pop-up waste (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (swivel) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disk headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a single sequential headworks with single lever type operating members. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge, verified by test (as suitable for backflow protection against Fluid Category 2). Maximum working pressure 5 bar. Maximum operating temperature 65°C
Range of press fittings with a brass body and EPDM ‘O’-rings for use with copper pipe manufactured to EN1057:2006 +A1:2010 seamless round copper tube R250. Joints are achieved using a specialist press fitting tool. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of pillar taps (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straighteners. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disk headwork’s with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Exposed wall mounted bar shower mixer (chrome plated brass body), incorporating a two-way ceramic disc diverter headwork controlling the flow with a cubed type operating member. Temperature is controlled independently via a thermostatic cartridge with a cubed type member that incorporates a manual override button. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). The product is supplied with a shower handset, shower hose, overhead shower and a riser rail assembly. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet swivel combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of T-type thermostatic mixing valves with brushed chrome plated DZR brass bodies for use with copper pipe (manufactured to BS EN 1057). All inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly operated spherical valves with brushed chromium plated brass bodies, chromium plated brass ball and PTFE seat. Maximum working pressure model K656: ¼” to ½” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Model K6566 model: ¼” to ⅜” = 64.0 bar, ¾” to 1¼” = 50.0 bar, 1½” to 2” = 40.0 bar, 2½” to 4” = 25.0 bar. Models K8912 , K8913 & K6568 models: ¼” to ⅜” = 64.0 bar. Maximum operating temperature 99°C.
Two hole, single outlet (fixed) combination tap assembly (chrome plated brass body), Incorporating non-rising spindle headworks with dome type top operating members. The product incorporates a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose, handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of pillar taps, (chrome plated brass bodies) incorporating non-rising spindle headworks with dome or cross-top type operating member. Model (C02065) incorporates a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two-hole, single outlet, fixed combination tap assembly (chrome plated brass body) incorporating non-rising spindle headworks with a dome type operating members. The spout outlet incorporate a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Two hole, single outlet swivel combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating a non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Product is supplied with a lever operated pop-up waste (not verified by test) Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of pillar taps (chromium plated brass) incorporating non-rising spindle headwork with cross top operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 7.0 bar. Maximum operating temperature 65°C.
Range of pillar taps (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straighteners. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset and metal back nuts. Models VAL2 BSM E6 C CD & VAL2 BSM E8 C CD come supplied with flow restrictors. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of two hole, single outlet (swivel) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disk headworks and lever operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10 bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disk headwork’s with single lever operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Jet range of water meters with brass blue epoxy coated bodies and EPDM rubber ‘O’-rings. Maximum working pressure16.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic flow straightener or plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of stainless steel inter-locked shower hoses incorporating PVC linings in various finishes. Maximum operating temperature 65°C.
Shower handset with various finishes. Maximum operating temperature 65°C.
Shower handsets with (brass or plastic bodies – various finishes), incorporating a stainless-steel strainer on the inlets. Open outlet use only Maximum operating temperature – 85°C.
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of CU type press copper crimp fittings with EPDM ‘O’-rings for use with copper tube manufactured to EN 1057. The joints are achieved by means of a crimping tool. For above ground use. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of shower handsets and overhead shower with various finishes. Model HS149 incorporates a stainless steel strainer washer at the inlet. Maximum operating temperature 65°C.
Two-hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless strainer and an approved single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 10 bar. Maximum operating temperature 65 °C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of butterfly valves with an epoxy coated ductile iron body, stainless steel disc and single lever or handwheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Single hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating non-rising spindle headworks with dome type operating members. The spout outlet incorporates a plastic flow straightener. Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve activated via an infra-red sensor. The tap connects to the solenoid valve via a copper tail with a ½” BSP (F) captive nut and a fibre washer. The product is supplied with a combined TPE washer and stainless steel strainer to be installed on the inlet to the solenoid. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of wall mounted shower outlets (chrome plated brass bodies). Maximum operating temperature 85°C.
Range of thermostatic bar shower mixers, incorporating a quarter turn ceramic disc headwork controlling the flow with a dome type of operating member. The temperature is controlled independently via a thermostatic mixing cartridge incorporating a manual override button. Inlets incorporate single check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Supplied with a shower hose, handset and a riser rail. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Range of thermostatic bar shower mixers, (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with a dome type operating member. Temperature is controlled independently via a thermostatic mixing cartridge with a dome type operating member that incorporates a manual override button. The Inlets incorporate stainless steel strainer washers and approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Two hole, single outlet (swivel) combination tap assembly (chrome plated brass) incorporating non rising spindle headworks with cross top operating members. The spout outlet incorporates a plastic flow straightener. Supplied with metal back nuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of in-line spherical ball valves with brushed chrome brass bodies and PTFE seats. Incorporating lever or T-type operating members. Maximum working pressure: 15mm - 28mm 30 Bar, 35mm - 25 Bar Maximum operating temperature; 99°c
Range of crimp fit spherical valves incorporating brushed chrome plated DZR brass bodies and ball, and PTFE seats. The products are supplied with lever operating members. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 99.0°C
Range of pillar taps (chrome plated brass bodies), incorporating non-rising spindle headworks with dome type operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
