'NBR 70.10-02 'O' rings and gaskets'. Black coloured, injection moulded NBR rubber 'O' rings and gaskets. Tested in-radius size between 0.5mm & 2.6mm. Shore hardness 70. For use with water up to 23°C.
'kSil PL60 Translucent'. Off-white coloured (translucent), silicone rubber material which is extruded onto the calendar. Shore hardness 60. Tested in-radius size 1.05mm. For use with water up to 85°C.
‘Loctite® 55’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Technical Data Sheet ‘reference 1.9’, dated August 2016 and this material is only approved for these conditions. For use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of inlet control valves with DZR brass bodies incorporating a pressure reducing valve (set at 1.5, 1.8. 2.0, 2.1, 3.0 or 3.5 depending on model) and a pressure relief valve (set at 3.0, 3.5, 4.5, 5.0. 6.0 or 8.0 depending on model. All models incorporate a stainless-steel mesh and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Model CWIC355040 comes supplied with a tundish. For use with copper pipe to BS EN 1057, PB pipe (with inserts) to BS EN 7291-2:2010 and PEX pipe (with inserts) to BS EN 7291-3:2010. Maximum working pressure 16.0. Maximum operating temperature of 25°C.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of boiling water dispensers incorporating plastic (3-7.5 litre models) or stainless steel (10-40 litre models) cisterns with silicone ‘O’-rings and seals. The flow to the internal reservoir is controlled via a float valve. The internal reservoir incorporates an overflow which acts a vent. The inlet incorporates a plastic filter. Water is dispensed using either a lever or push button (PLUS models only) operated self-closing tap. Maximum working pressure 5.0 bar. Maximum operating temperature 98°C. Cold supply only.
Range of single hole or two-hole pre-rinse taps (chromium plated brass bodies) which have either a single outlet or two outlets. The flow is controlled by rising spindle headworks with single lever operating members and the spout outlet incorporates a plastic flow straightener. Model 89001MN-2 is a single hole tap with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98001-1, 98001-1-01, 98001MN-1, 98001MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-2, 98007MN-2-01, 98007-2 & 98007-2-01 are two-hole taps with two outlets; a spout (swivel) outlet and pull-down pre-rinse assembly which incorporates a trigger mechanism. Models 98007MN-1 & 98007MN-1-01 are two-hole taps with a single outlet; a pull-down pre-rinse assembly which incorporates a trigger mechanism. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (fixed) combination tap assembly with brass body (various finishes), incorporating ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a lever operated pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. The spout outlet incorporates either a plastic aerator or flow straightener, (Model 193838EX,193838EX MBK1, 163838EX & 163838EX MBK1 is only supplied with an aerator) . The product is supplied with a click type waste (verified by test). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated bodies), incorporating ceramic cartridge headworks with single lever operating members. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Single-hole, single outlet fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, fixed, combination tap assemblies (brass bodies - various finishes ) incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Products are supplied either with or without a lever type pop-up waste set (see models). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The inlets of 2621 models incorporate plastic strainers and approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets of 26216 models incorporate single check valve cartridge assembly (suitable for backflow protection against fluid category 2), plastic strainers and a single lever operated spherical valves. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type pop-up waste or lever type pop up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The products are supplied with a click type pop-up waste verified by test. Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of deck mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headworks and various type operating members (see models). The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with a metal back nut. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with various - operating members and a self-cancelling diverter to shower outlet. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single hole, single outlet fixed combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The outlet to the shower incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates an aerator. These products are not supplied with shower handset and hose. Maximum working pressure 16.0 bar. Between May 2023 and July 2023, the taps have a maximum operating temperature of 65°C. From August 2023 the taps have a maximum operating temperature of 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies with (brass bodies -various finishes), incorporating ceramic cartridge headworks and single lever operating members. The Spout outlet incorporates a plastic aerator. Some models are supplied with a pop-up waste (see list). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single-outlet (swivel) combination tap assemblies, incorporating a ceramic cartridge headworks with a single lever operating member. A quatrer turn ceramic disc headwork with spring loaded return to the closed position controls flow of the boiling water outlet supply using single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar on the hot and cold supply, 3.0 bar on the boiling water supply. Maximum operating temperature 65°C on the hot and cold supply, 99°C on the boiling water supply.
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) with under counter boiling water unit (vented via the spout outlet) and in-line water filter (on instantaneous hot water supply only). Flow is controlled by a ceramic cartridge headwork with a single lever operating member. Instantaneous hot water is controlled by a self-closing quarter turn ceramic disc headwork with a single lever operating member. The product is supplied with loose 3/8” x 15mm reducers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 98°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Edition 11’ range of wall mounted, concealed, two hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass). Model T740005 incorporates ceramic cartridge headwoks. All other models incorporate quarter turn ceramic disc headworks with single lever operating members. Spout outlets incorporate plastic flow straighteners except T8705 with is open. All products are supplied with metal back nuts. T7505M, T8705, T8805, T7115 and T749005 maximum working pressure 5.0 bar, Maximum operating temperature 60°C. T739005 maximum working pressure 16 bar max operating temperature 65°C. T740005 maximum working pressure 10 bar max operating temperature 65°C.
Range of two-hole, single outlet combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener The product is supplied with plastic backnuts. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar. temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightener (63615-500107 and 62629-510107 models) or a plastic aerator (all other models). Maximum working pressure 5.0 bar.
Deck mounted, two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout incorporates a waterfall outlet. Each inlet incorporates a plastic flow regulator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, two hole, single outlet (fixed) combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with various types of operating members (see models). All spouts incorporate plastic aerators except model F6125. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members and a cascade type spout. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see models), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. The product incorporates brass backnuts. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes), incorporating quarter turn ceramic disc headworks and a manual diverter to shower outlet. Operating members not supplied. Maximum working pressure 5.0 Bar temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with dome type operating members and a manually operated diverter to the shower outlet. The spout outlets incorporate plastic flow straighteners. The product is supplied with a shower hose, shower handset and metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet, fixed, combination tap assemblies (chrome plated brass), incorporating a manual diverter controlling the flow to the overhead or hand shower and a thermostatic cartridge controlling the temperature with dome operating member incorporating a manual override button. The spout outlet incorporates quarter turn ceramic disc headwork which diverts between the spout and shower outlets and the spout outlet incorporates a plastic aerator. The inlets incorporate a stainless-steel strainer and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Not supplied with shower hose or shower outlets. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Two-hole, single outlet (fixed) combination tap assemblies incorporating a half-turn ceramic disc headwork with cross top or single lever operating members and manual diverter to a shower outlet. Supplied with metal back nuts. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout incorporates and a self-cancelling diverter to the shower outlet and plastic aerators. The shower outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow prevention. This product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Three hole single outlet combination tap assembly (chromium plated brass body) with quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates an aerator. This product is supplied with stainless steel braided PEX lined flexible hose assemblies which connect from the inlets to the spout. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, three-hole, single outlet (fixed) combination tap assemblies (various finishes, see model) incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of combined bath fillers and overflow waste assemblies (plated brass covers and plastic hoses) with pop-up wastes. Maximum operating temperature 65ºC. Open outlet use only.
Range of wall mounted fixed spout outlets (brass or stainless-steel bodies – various finishes). Incorporating a self-cancelling diverter to shower outlet with a dome type operating member and a plastic aerator at the outlet. Most models are supplied with shower hose and handset. T2 models are not supplied with a shower handset.
Non-metallic materials and components comply with BS6920 at 65°C
Range of swivel spout outlets (brass or stainless-steel bodies - various finishes), incorporating plastic aerators.
Non-metallic materials and components comply with BS6920 at 60°C
Basin spout outlet with a brass body (chromium plated brass) incorporating a plastic flow straightener. The product is supplied with a metal back nut. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
The “TH Instantor” range of press fittings and pipe. Fittings incorporate EPDM ‘O’-rings Maximum working pressure 10 bar. Maximum operating temperature 95°C
‘Unidelta’ brass compression fittings for use with ‘Unidelta UniTerm’ PEX pipe. Maximum working pressure 8.0 bar @ 85°C, 20.0 bar @cold water use.
Page 74 of 171
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
