Range of compression fittings with brass bodies for use with copper pipe (EN1057). Above ground use only. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of end feed copper fittings for use with copper tube to EN 1057. The HLDPMFWT and HLDPMFZT models incorporate a captive nut on one end with a fibre gasket washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of float operated electrical switches with plastic bodies. Cold water use only.
Range of water meters with brass (CW724R & CC770S) and plastic (Composite) bodies, incorporating plastic strainers and EPDM ‘O’- rings. Maximum working pressure 16.0 Bar. Temperature: 60.0°C for brass (CW724R & CC770S) models & Cold water use only for composite models.
Talbot Modular Manifold System with and without concentric water meter connections with plastic bodies incorporating screw down stopvalves. Maximum working pressure 16 bar. Cold water use only.
‘DM900’ range of flow measuring devices with stainless steel bodies. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of pressure, flow and temperature sensors. The VFI sensors have stainless steel bodies, all other models have plastic bodied sensors. The MFS and VFS models are supplied with a plastic (composite) or stainless-steel flow pipe. The VFI models are supplied with a stainless-steel flow pipe. The products can also be supplied with a range of fittings/end connections (see model and size). Maximum working pressures: ITS, LPS, RPS, MFS (composite flow pipe) and VFS (composite flow pipe) models: 24.0 bar. CPS models (added February 2024): 24.0 bar. DPS: Models with vent hole: 16.0 bar. All other models: 24.0 bar. MFS (stainless steel flow pipe) and MFS (stainless steel flow pipe): 30.0 bar. VFI non-flanged models: 30.0 bar. VFI flanged models: 30.0 bar or as per flange PN rating 16.0 bar or 25.0 bar (whichever is lower). Maximum operating temperature 99°C.
Range of circulator pumps with brass bodies, plastic impellor, and EPDM ‘O’-rings and seals. The COMFORT 15-14 BX prefix models incorporate a screwdriver operated isolation valve on the inlet and a non-return valve at the outlet. These are housed within 1” BSP (M) x ½” BSP (M) adaptors. Maximum working pressure 10.0 Bar. Maximum operating temperature 95°C.
Range of multistage pumps (VL and CL series) and submersible pumps (VN, CN, ES and CS series) with stainless steel bodies and impellers and NBR gaskets and ‘O’-rings. Maximum working pressure 15.0 bar (VL and CL series pumps only).
Range of vertical multistage pumps with either stainless-steel bodies (“N” versions) or cast iron bodies with a black electrodeposition coating (“G” versions), stainless-steel impellers, shaft and outer sleeve. Maximum working pressure: EV30, EV45, 30VR & 45VR models - 32.0 bar, EV65, EV95, 65VR & 95VR models - 25.0 bar. Max operating temperature: Stainless steel (“N” versions) - 100°C. Cast iron (“G” versions) - Cold water use only.
Single stage centrifugal pump, with plastic impellers. The pump is equipped with ceramic bearings; the body and shaft are made of stainless steel. The product is supplied with loose fibre/NBR inlet/outlet gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of circulator pumps with stainless steel bodies and a plastic impeller. All models are available with a plastic (composite) rotor can, the MAGNA1 range is also available with a stainless-steel rotor can in the DN32 flanged, threaded 1½ & 2” sizes only. The MAGMA3 models have a differential pressure sensor. Maximum working pressure 10.0 bar. Maximum operating temperature 99°C.
Range of shower handsets (plastic bodies – various finishes).
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets and an overhead shower outlet with plastic bodies (chrome plated, chrome plated/white or chrome plated/black coloured finish - see model). The inlet of the 2.1981.018 model incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Non-metallic materials and components comply with BS6920 at 55°C
Range of overhead shower outlets (brass bodies – various finishes). The inlets incorporate a plastic flow regulator. Model 26 221 xxx and 26 465 xx0 incorporates a stainless-steel strainer, all other models incorporate a plastic strainer. Maximum operating temperature 60.0°C. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets (chrome plated brass bodies) incorporating NBR ‘O’ rings.
Non-metallic materials and components comply with BS6920 at 65°C
Range of shower outlets (brass or stainless-steel bodies – various finishes) incorporating EPDM O-rings. Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted shower outlet (brass body – various finishes). The product is supplied with shower hose and handset that incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Non-metallic materials and components comply with BS6920 at 60°C
Range of shower handsets & overhead shower outlets with chromium plated plastic body. The inlets of the overhead shower outlets incorporate a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with (brass bodies – various finishes), incorporating EPDM `O`-rings and a plastic strainer. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of overhead shower outlets with brass or stainless-steel bodies (various finishes - see model), with NBR ‘O’-rings. The inlet incorporates a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 70°C
Range of draining taps with DZR brass, brass or chrome plated brass bodies. Incorporating a rising spindle headwork, EPDM or NBR seals and washers. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Pillar taps with chromium plated - brass bodies incorporating a quarter turn ceramic disc headwork, with single lever type operating members. The spout outlet incorporates a flow straightener. The product is supplied with plastic backnuts. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 45°C
Range of pillar tap (chrome plated brass), incorporating quarter ceramic disc headworks with single lever or dome type operating members. The spout outlets incorporate plastic aerators. Products are supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of dual layer reinforced hose assemblies, with elbow and straight end fittings, For use with free standing appliances. Available with a grey, blue, red or white PVC outer layer and black PVC inner layer, and EPDM or NBR gaskets. End connections incorporate plastic filters. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of stainless steel, PVC and nylon braided shower hoses (various finishes), incorporating PVC, EPDM or PEX liners and various end connections.
Range of stainless-steel braided EPDM lined flexible hose assemblies with a variety of end connections. Some models incorporate screwdriver operated isolation valves. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Air vent valve with a brass body and plastic float. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Wall mounted, manually operated shower mixers with brass bodies – various finishes, incorporating a ceramic cartridge headwork, and a single lever operating member. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic bar shower mixers, (brass bodies - various finishes), incorporating two way diverter valve controlling the flow with dome type operating members. Temperature is controlled independently via a thermostatic cartridge with dome type operating members that incorporate a manual override button. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a shower hose, handset and overhead shower and riser rail assembly. The handset with model RTSDEF also incorporates a flow regulator. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of high pressure and low pressure thermostatic mixing valves. Flow is controlled by a solenoid valve and temperature is thermostatically controlled. Low pressure models incorporate a pump. The inlets of the valves incorporate an isolation valve, stainless steel strainer and a single check valve cartridge however, the complete assembly has not been tested to demonstrate it provides adequate backflow protection. The valves can be supplied with a shower rail, hose, handshower and/or ceiling mounted shower outlet. Valves with ‘HP’ in model have a maximum working pressure of 5.0 bar. All other valves marked with ‘LP’ have a maximum working pressure of 1.0 bar.
Non-metallic materials and components comply with BS6920 at 45°C
Range of wall mounted,two hole,single outlet,thermostatically controlled combination tap assemblies (Chromium plated brass). Flow is controlled between the spout outlet and overhead shower by a 2 way ceramic disc diverter with adome type operating member. Temperature is controlled via a thermostatic cartridge with adome type operating member and a manual override button. The spout outlet can be turned 90 degrees to divert the flow to a further shower outlet. The spout outlet incorporates a plastic aerator. Each inlet incorporates a stainless steel strainer and approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of concealed, thermostatic blending valves with 2 or 3 shower outlets, incorporating a thermostatic cartridge controlling the temperature with a dome type operating member that incorporates a manual override button and ceramic disc diverters or quarter turn ceramic disc headworks controlling the flow with dome type operating members. The products incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow prevention. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, concealed, thermostatic blending valves with (brass bodies - various finishes, see models). The temperature is controlled via a thermostatic cartridge with single lever, cross top or cube type operating members incorporating a manual override button. Both inlets incorporate a stainless-steel strainer and an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, wall mounted, thermostatic blending valves, (brass bodies, chrome trim sets). The products can consist of quarter turn ceramic disc or detent headworks, two-way diverter cartridges and a thermostatic cartridges (see models). All models incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, thermostatic shower valves, (brass bodies - various finishes), incorporating a ceramic disc diverter cartridges controlling the flow with dome type operating members. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with an overhead shower, shower hose, handset and riser rail assemblies. Maximum working pressure 10 Bar. Maximum operating temperature 60 °C
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed thermostatic shower mixing valves with (brass bodies - various finishes), incorporating a ceramic disc diverter valve controlling the flow between two outlets. The temperature is controlled independently via a thermostatic cartridge with a manual override button. The products are supplied with trim sets and operating members in a various finishes. The 15 708 xxx model has cube type operating members, and all other models have single lever operating members. Both inlets incorporate an approved check valve cartridge (however, the complete product has not been fully tested to demonstrate it provides backflow protection) Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of double flanged, wafer or lugged butterfly valves with polyester coated ductile iron, cast iron or carbon steel bodies. The discs of the S3 range are available in stainless steel, nylon coated or aluminium bronze. The discs of the S2 range are stainless steel. Maximum working pressure for the S2 range is 10.3 bar. Maximum working pressure for the S3 range is 17.2 bar. Maximum operating temperature 99°C.
Range of bath mixer valves with brass bodies, incorporating a ceramic cartridge headwork, single lever operating members and self cancelling diverter to bath and shower outlet. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of concealed shower mixer valves with brass bodies, incorporating a ceramic cartridge headwork, single lever operating members. Model 72 668 xxx to be installed with iBox universal which is not part of this approval Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
`535` range of adjustable, in-line pressure reducing valves with DZR brass bodies, incorporating a spring loaded EPDM diaphragm and a gauge port. The 535022 compression model is for use with copper pipe (manufactured to EN1057). The product incorporates an intergal stainless steel strainer. Models can be supplied with or without a pressure gauge (see model), which inserts in the test port location. The outlet pressure range is adjustable between 1.0 and 6.0 bar. Maximum inlet supply pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
‘Jet 806’ range of pre-set pressure relief valves incorporating gunmetal bodies, PTFE seat and lever operated easing gear. Each valve is available with a pre-set rating of between 1.0 bar and 12.5 bar, in increments of 0.1 bar. Maximum operating temperature 95˚C.
Range of factory pre-set, pressure relief valves with gunmetal bodies, incorporating fluoro-elastomer & FKM ‘O’-rings, PTFE seat seals and chrome vanadium steel springs. Maximum working pressure varies by model and spring. Fig 500L (Brown spring) - 4.1 bar – 6.1 bar. (Blue spring) - 6.2 bar – 8.2 bar. (Purple spring) - 8.3 bar – 10.2 bar. (Black spring) - 10.3 bar – 12.5 bar. Fig 542L (Brown spring) - 3.3 bar – 4.9 bar. (Blue spring) - 5.0 bar – 6.5 bar. (Purple spring) - 6.6 bar – 8.2 bar. (Black spring) - 8.3 bar – 10.5 bar. Maximum operating temperature 95˚C
Pre-piping arrangement consisting of a framework fitted with a range of spherical valves with brass bodies and balls, PTFE seats and EPDM ‘O’-rings. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of inline spherical valves (nickel plated brass bodies) incorporating chrome plated brass balls, PTFE seats and washers with single lever, T-type or lockshield operating members. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Boss Range of inline spherical valves (nickel plated brass bodies) incorporating chrome plated brass balls, PTFE seats and washers with single lever, T-type or lockshield operating members. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated spherical valves with nickel-plated brass bodies and ball with a PTFE seat. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of spherical valves with stainless steel bodies, chrome plated brass ball and PTFE seats. Maximum working pressure 68.9Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 44 of 81
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
