'Kealox 96% & 99.7%'. White coloured, compression moulded ceramic rings. For use with water up to 85°C.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'ERIKS 55950 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
'FKM 90 Black 6019020105-CMP00700'. Black coloured, compression moulded FKM material. Shore hardness 90. Tested in-radius size 1.1mm. For use with water up to 85°C.
‘N5118F, N5518F, N6118F, N6518F, N7118F, N7008F, N7518F, N8118F, N8518F & N9118F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
‘Loctite® 55’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Technical Data Sheet ‘reference 1.9’, dated August 2016 and this material is only approved for these conditions. For use with water up to 85°C.
3-in1 single hole, single outlet (swivel) combination tap assembly (chromium plated or brushed stainless steel PVD brass). The cold//hot/mixed water circuit incorporates a ceramic cartridge headwork with a single lever operating member. The near boiling water circuit incorporates a quarter turn ceramic disc headwork with a single lever operating member. The tap is supplied with a stainless steel braided PEX lined flexible hose assembly, brass adaptor incorporating a plastic flow regulator, NBR washer and plastic adaptor to connect the tap to the near boiling water unit (not supplied) and a PTFE or silicone (from September 2024) flexible pipe to deliver near boiling water back to the tap. The spout outlet incorporates a plastic aerator, which includes a central stainless steel tube insert throughout the near boiling water outlet of the aerator. Maximum working pressure 10.0 bar. Maximum operating temperatures: 65°C (cold/hot/mixed water circuit). 99°C (near boiling water circuit after boiler unit, cold supply only prior to boiler unit).
Single hole, single outlet (fixed) electronically controlled combination tap assemblies (chromium plated). The flow is controlled by a solenoid valve activated via an infra-red sensor. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose and a manual lever for controlling the temperature. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and a manual lever to control the outlet temperature. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Temperature:60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass bodies). Flow is controlled via a solenoid, activated via an infra-red sensor. The outlets incorporate plastic aerators. Maximum working pressure 8.0 bar Maximum operating temperature 70°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Undercounter boiling water cistern with a stainless steel body, stainless steel element and silicone ‘O’-rings and gaskets. Maximum working pressure 8.0 bar. Maximum operating temperature 95°C.
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Range of ceramic cartridges or 2-way ceramic disc diverter headworks with plastic bodies, EPDM ‘O’-rings and/or gaskets, for insertion into specifically dimensioned bores. The JA01AJ and AH01AJ models incorporate a thermostatic element. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Ceramic cartridge headwork with a PPO body and silicone gaskets for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet (swivel) combination tap assemblies (various finishes) incorporating ceramic cartridge headworks with single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. The inlet hoses incorporate stainless steel strainers. Models 5059340452869 have a maximum working pressure of 10.0 bar. All other models have a maximum working pressure of 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of floor mounted, single hole, single outlet fixed combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a self- cancelling diverter to shower outlet. This spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating a ceramic headwork with single lever operating members. The products incorporate a connection for filtered water supply controlled by quarter turn ceramic disc headwork. The spout outlets incorporate plastic aerator. A separate supply for Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly (brass bodies - chrome finish), incorporating a ceramic cartridge headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (brass bodies – various finishes) incorporating quarter turn ceramic disc or ceramic cartridge headworks with single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 BAR
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted two hole, single outlet, combination tap assemblies with brass bodies, incorporating a ceramic cartridge headwork and single lever operating member. This product incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Deck mounted, two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to shower outlet. The spout incorporates a waterfall outlet. Each inlet incorporates a plastic flow regulator. The product is supplied with a shower hose and handset, and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Two-hole, single outlet, (fixed) combination tap assemblies, (brass bodies – various finishes) incorporating a quarter turn ceramic disc headwork and a thermostatic cartridge with cubed type operating members incorporating a manual override button. The spout outlet incorporates a plastic aerator. The inlets incorporate approved check valve cartridge(s); however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted two-hole, single outlet (fixed) combination tap assembly (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member, and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Deck mounted, two-hole, single outlet (fixed) combination tap assemblies, (chrome plated brass bodies) incorporating quarter turn ceramic disc headworks with single lever operating members and lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. Product is supplied with shower hose, shower handset and metal backnut. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes). Incorporating quarter turn ceramic disc headworks with single lever, cross top, or dome type operating members. The spout outlets for models (F4184, F6182B & F9484) incorporate a plastic aerator and models (F6182C & F8118) are open outlet. The products are supplied with stainless-steel braided EPDM lined flexible hoses to headworks to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating quarter turn ceramic disc headworks with single lever or cross top operating members. The spout outlet incorporates a plastic aerator, and the products are supplied with a lever type pop-up waste. The products are also supplied with either stainless steel or nylon braided PEX lined flexible hoses for connection between the headworks and the spout outlet. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of three-hole, metal, single outlet (fixed), wall mounted combination tap assemblies (brass body, black finish) incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, four hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a 2-way ceramic disc diverter headwork controlling the flow between the spout and shower outlet. Temperature is controlled independently by a thermostatic cartridge. The ARR-132T-CP model has single lever operating members and the ARR-232T-CP model has cross top operating members. Each inlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset, and has metal backnuts. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted spout outlet with chromium plated brass body incorporating a plastic flow regulator on the inlet and a plastic strainer at the outlet. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted spouts (chrome plated brass) with a plastic aerator at the outlet. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Five-hole, single outlet (fixed) combination tap assembly (brass body - various finishes), incorporating quarter turn ceramic disc headworks with cube type operating members and a manually operated diverter to the shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible connection hoses to connect the headworks, spout and diverter. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Deck mounted, swivel spout outlet with a chromium plated brass body, incorporating a plastic aerator at the outlet. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of horizontal or vertical expansion vessels with an EPDM membrane. Maximum working pressure 10.0 or 16.0 bar (please refer to model). Maximum operating temperature 100°C.
Range of in-line water filters with polypropylene bodies. Maximum working pressure 8.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at cold water use only°C
Range of in-line water filters with polypropylene bodies. Maximum working pressure 8.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at cold water use only°C
Range of in-line water filters with polypropylene bodies. Maximum working pressure 8.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at cold water use only°C
Range of in-line water filters with polypropylene bodies. Maximum working pressure 8.5 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at cold water use only°C
Page 39 of 86
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
