'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250655046

Expiry date:

30/06/2030

Approval Holder:

Gee Tec

Company Name

Gee Tec

Address

24 Industrial Area, Phagwara, Punjab, 144401

Country

India

View All Listings by this Company

'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per Nav Durga Chromatics Private Limited data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250655047

Expiry date:

30/06/2030

Approval Holder:

Sigma Flow Control India Ltd.

Company Name

Sigma Flow Control India Ltd.

Address

Tobacco House, Room #506 5th Floor, 1 & 2 Old Court House Corner, Kolkata - 700001, West Bengal

Country

India

View All Listings by this Company

'PMSP5112-M, PMSP5113-M, PMSP5114-M, PMSP5115-M, EP5112D01SC, EP5113D01SC, EP5114D01SC & EP5115D01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 37', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250955015

Expiry date:

30/09/2030

Approval Holder:

Colorobbia Italia S.p.A.

Company Name

Colorobbia Italia S.p.A.

Address

Via Pietramarina 53, I-50053 Sovigliana-Vinci (Firenze)

Country

Italy

View All Listings by this Company

'NMSP2251M, NMSP2265M, NMSP2266-M, NMSP2267-M, ER2251A01SM, ER2265A01SM, ER2266A01SC, ER2267A01SC'. Factory applied, blue coloured, Porcelain Vitreous Enamel coatings. Apply as per manufacturer's User Manual 'PEM 38', 'Edition 01', dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250955016

Expiry date:

30/09/2030

Approval Holder:

Colorobbia Italia S.p.A.

Company Name

Colorobbia Italia S.p.A.

Address

Via Pietramarina 53, I-50053 Sovigliana-Vinci (Firenze)

Country

Italy

View All Listings by this Company

'FGB15A -White, FGB15A -21364A Grey & FGB15A -21404A Grey'. ISOPOL modified, white or grey coloured brush Gelcoats. Apply as per manufacturer's TDS dated '04/11/2022'. Cure for 120 minutes@18°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

250555061

Expiry date:

31/05/2030

Approval Holder:

Colorplas Ltd

Company Name

Colorplas Ltd

Address

Moss Bridge Road, Rochdale, Lancashire

Postcode

OL16 5NU

Phone

01706 351888 Email: sales@colorplas.com

General Email

np@colorplas.com

View All Listings by this Company

‘2KPS EASF-V Fading Blue’ & ‘2KPS EASF-V Grey’. Site applied, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0104’, dated ‘04/06/2023’. 2KPS EASF-V Fading Blue is for use with water up to 65°C. 2KPS EASF-V Grey is for use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.

Section:

5311 Resin Anchors

Expiry date:

30/06/2030

Approval Holder:

2K Polymer Systems Ltd.

Company Name

2K Polymer Systems Ltd.

Address

Venture Crescent, Alfreton, Derbyshire

Postcode

DE55 7RA

Phone

+44 (0) 1773 527 333

General Email

info@2kps.net

View All Listings by this Company

Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass), flow is controlled by a solenoid valve, activated via an infra-red sensor. The product is supplied with a combined TPE washer and stainless-steel strainer to be installed on the inlet to the solenoid. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.

Section:

0684 Combination Tap Assemblies

Section Subtitle:

Tap(s) with a non-touch methods of flow control and a single inlet.

WRAS Approval Number:

251008004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

R008 applies to solenoid only.

Size:

½” BSP (M) on solenoid.

Marking:

INTA, date of manufacture (WW/YY) and model on body.

Installation Requirements:

R001 R006 R008

Expiry date:

31/10/2030

Model:

D67514 - SARACEN Infra Red Tap Battery Operated D67513 - SARACEN Infra Red Tap Mains Operated

Approval Holder:

Wolseley UK Ltd.

Company Name

Wolseley UK Ltd.

Address

2 Kingmaker Court, Warwick Technology Park, Warwick

Postcode

CV34 6DY

Country

United Kingdom

Phone

01926705792

General Email

martin.lister@wolseley.co.uk

View All Listings by this Company

Section:

2011 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control, incorporating a manual diverter between outlets.

Wall mounted. Two-way diverter valve. Incorporates an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides backflow protection)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

31/08/2030

Product Images

Approval Holder:

ZHEJIANG XINDONG SANITARY WARE CO.,LTD.

Company Name

ZHEJIANG XINDONG SANITARY WARE CO.,LTD.

Address

XUANMEN INDUSTRIAL ZONE YUHUAN CHINA

Country

CHINA

View All Listings by this Company

Manufacturers:

Zhejiang Xindong Sanitary Ware Co., Ltd

Section:

2011 Shower Valves

Description:

A Range of Shower valve(s) with thermostatic temperature control, incorporating a manual diverter between outlets.

Wall Mounted Incorporates a check valve cartridge, however the complete assembly has not been tested to demonstrate it provides backflow protection.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R020

Expiry date:

30/09/2030

Approval Holder:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Company Name

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Address

No.57, Sijiu Road, Zhishan Town, Heshan City, Guangdong

Country

China

General Email

2894475300@qq.com

View All Listings by this Company

Manufacturers:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Section:

2052 Diverter

Description:

A Range of Diverter(s) incorporating manual control

Plastic body/bodies

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001

Expiry date:

31/08/2030

Approval Holder:

Ningbo Wanhai Cartridge Technology Co. Ltd.

Company Name

Ningbo Wanhai Cartridge Technology Co. Ltd.

Address

Xiachen Development Zone, Chunhu, Fenghua

Country

Zhejiang, China

View All Listings by this Company

Manufacturers:

Ningbo Wanhai Cartridge Technology Co

Section:

0440 Headworks

Description:

A Range of Headwork(s) for installation into specifically dimensioned taps or shower valve bodies.

Plastic body/bodies

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001

Expiry date:

30/11/2030

Notes & Further Information

30 122 100 - Diameter= 25,4mm 30 122 101 - Diameter= 25,4mm 30 333 001 - Diameter= 25,4mm 30 746 700 - Diameter= 25,4mm 30 746 702 - Diameter= 25,4mm 30 579 600 - Diameter= 25,4mm

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Section:

0450 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a fixed spout.

Deck Mounted Stainless-steel braided PEX lined flexible inlet hoses Capable of AUK2 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R009 R010 R005

Expiry date:

31/10/2030

Approval Holder:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Company Name

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Address

No.57, Sijiu Road, Zhishan Town, Heshan City, Guangdong

Country

China

General Email

2894475300@qq.com

View All Listings by this Company

Section:

0450 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a fixed spout.

Deck mounted Stainless steel Braided PEX lined flexible hose assemblies incorporating 3/8 captive nut end connections. Supplied with a click type waste - not verified by test. Capable of achieving AUK3 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R009 R010

Expiry date:

30/11/2030

Notes & Further Information

Where xx0 denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturers:

Hansgrohe d.o.o.

Section:

0450 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a fixed spout.

Deck Mounted. Capable of achieving AUK3 Tap Gap. Stainless Steel braided EPDM lined inlet hoses. R160 applies to model 91202 only.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R010 R160

Expiry date:

30/11/2030

Approval Holder:

Yuhuan Bokeya Sanitary Ware Technology Co., Ltd.

Company Name

Yuhuan Bokeya Sanitary Ware Technology Co., Ltd.

Address

Saozhoushan Industrial Zone Qinggang Town, Yuhuan, Zhejiang

Postcode

317600

Country

China

General Email

105069040@qq.com

View All Listings by this Company

Manufacturers:

YUHUAN BOKEYA SANITARY WARE TECHNOLOGY CO., LTD.

Section:

0470 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a swivel spout.

Deck Mounted Stainless Steel and Polyamide braided, PE lined inlet hoses Capable of Achieving AUK3 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R009 R010

Expiry date:

28/02/2031

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturers:

Xiamen Lota International Co., Ltd.

Section:

0470 Combination Tap Assemblies

Description:

A Range of Single hole tap(s) with a single outlet and a swivel spout.

Deck Mounted Stainless-steel or nylon braided with PEX lined Inlet hoses Capable of Achieving AUK3 Tap Gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R009 R010

Expiry date:

30/11/2030

Notes & Further Information

Various finish: (1)Without suffix to current model number:Chrome plated (2)With suffix B:Black (3)With suffix BB:Brushed brass

Approval Holder:

Taizhou Shenglang Sanitary Ware Co., Ltd.

Company Name

Taizhou Shenglang Sanitary Ware Co., Ltd.

Address

Zhongshan Industrial Zone, Chumen Town, Yuhuan, Zhejiang

Country

China

View All Listings by this Company

Manufacturers:

Taizhou Shenglang Sanitary Ware Co, Ltd.

Section:

0470 Combination Tap Assemblies

Description:

A Single hole tap(s) with a single outlet and a swivel spout.

Deck Mounted Capable of Achieving AUK3 Tap Gap Stainless Steel and Polyamide braided, PEX lined inlet hoses

Installation Requirements:

R001 R006 R009 R010

Expiry date:

31/01/2031

Approval Holder:

BLANCO GmbH + Co KG

Company Name

BLANCO GmbH + Co KG

Address

Flehinger Strasse 59 Oberderdingen

Postcode

75038

Country

Germany

General Email

certification-water@blanco.de

View All Listings by this Company

Section:

0510 Combination Tap Assemblies

Description:

A Two hole tap(s) with a single outlet and a fixed spout.

Wall mounted Undefinable Air Gap - See IRN's

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

31/10/2030

Approval Holder:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Company Name

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Address

No.57, Sijiu Road, Zhishan Town, Heshan City, Guangdong

Country

China

General Email

2894475300@qq.com

View All Listings by this Company

Manufacturers:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Section:

0510 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and a fixed spout.

Wall Mounted.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R010 R040

Expiry date:

30/11/2030

Notes & Further Information

The first * stands for the different handle A, B,C and D, if there is no handle, no first * ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed

Approval Holder:

Guangzhou KIND Architecture Material Technology Co., Ltd.

Company Name

Guangzhou KIND Architecture Material Technology Co., Ltd.

Address

Unit 10, No.1 Dashadi West, Huangpu District, Guangzhou, Guangdong Province

Postcode

510700

Country

China

Phone

+86-20-23371404

General Email

sale@watersino.com

View All Listings by this Company

Section:

0520 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a single outlet and a fixed spout, incorporating a manually operated diverter to a shower outlet.

Deck mounted Supplied with PVC lined flexible hose assembly with corrugated metal outer covers & shower handset Capable of achieving AUK3 tap gap

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006 R010 R020

Expiry date:

31/10/2030

Approval Holder:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Company Name

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Address

No.57, Sijiu Road, Zhishan Town, Heshan City, Guangdong

Country

China

General Email

2894475300@qq.com

View All Listings by this Company

Manufacturers:

Guangdong Kinen Sanitary Ware Industrial Co., Ltd.

Section:

0520 Combination Tap Assemblies

Description:

A Two hole tap(s) with a single outlet and a fixed spout, incorporating a manually operated diverter to a shower outlet.

Deck Mounted Capable of achieving AUK2 Tap Gap Incorporates an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides backflow protection)

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R005 R010 R040

Expiry date:

31/10/2030

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Section:

0570 Combination Tap Assemblies

Description:

A Range of Two hole tap(s) with a double outlet and a swivel spout.

Deck Mounted. Capable of achieving AUK3 Tap Gap.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R006

Expiry date:

30/11/2030

Approval Holder:

MVI Hazel Ltd.

Company Name

MVI Hazel Ltd.

Address

1 Mygan Business Park, Jamestown Road, Finglas, Dublin 11

View All Listings by this Company

Range of chemical dosing equipment which incorporate self-closing valves and plastic bodies. The outlet of the injector incorporates a connection for injection of chemicals via venturi action and the inlets include stainless-steel strainers. Maximum operating pressure 9 bar. Maximum operating temperature 70°C.

Section:

0970 Dosing Equipment

Section Subtitle:

Fittings in this section have been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which they have been designed

WRAS Approval Number:

251004710

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Only suitable for use with chemicals no greater than a FC3, additional backflow protection is required for chemicals greater than FC3. Must be installed in the vertical plane.

Size:

¾” BSP male inlet

Marking:

SEKO, max pressure, max temperature and other technical info on label.

Installation Requirements:

R001 R040 R160

Expiry date:

31/10/2030

Model:

PXB1F04 PROMAX BUTTON FLEX-GAP 4L/MINPRODUCT PXB1F16 PROMAX BUTTON FLEX-GAP 14L/MINPRODUCT PXB1F30 PROMAX BUTTON FLEX-GAP 30L/MINPRODUCT PXB4F04 PROMAX BUTTON FLEX-GAP 4L/MINPRODUCT PXB4F16 PROMAX BUTTON FLEX-GAP 14L/MINPRODUCT PXB4F30 PROMAX BUTTON FLEX-GAP 30L/MINPRODUCT PXS1F04 PROMAX SLIDE FLEX-GAP 4L/MINPRODUCT PXS1F16 PROMAX SLIDE FLEX-GAP 14L/MINPRODUCT PXS1F30 PROMAX SLIDE FLEX-GAP 30L/MINPRODUCT PXS4F04 PROMAX SLIDE FLEX-GAP 4L/MINPRODUCT PXS4F16 PROMAX SLIDE FLEX-GAP 14L/MINPRODUCT PXS4F30 PROMAX SLIDE FLEX-GAP 30L/MINPRODUCT

Approval Holder:

SEKO S.p.a

Company Name

SEKO S.p.a

Address

Viale Luigi Schiavonetti 274 F Roma

Postcode

00173

Country

Italy

General Email

f.pompeo@seko.com

View All Listings by this Company

Range of ceramic filter cartridges with a plastic body. Cold water and open outlet use only.

Section:

1055 Filter Cartridges

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

Triflow logo and product info on cap

Installation Requirements:

R001 R008 R120 R150 R170

Expiry date:

30/11/2030

Model:

20681 Triflow Filter Cartridge 321 (TF321) - M15 Thread x 1.5mm. 8017714 Triflow Filter Cartridge 500 Push-Fit (TFE500) - 14.75mm Pushfit.

Approval Holder:

Triflow Concepts Limited

Company Name

Triflow Concepts Limited

Address

Global House 95 Vantage Point Pensnett Trading Estate Kingswinford

Postcode

DY6 7FT

Phone

0800 999 3959

General Email

lauren.cullingworth@triflowconcepts.com

View All Listings by this Company

Range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *‐KJ600304 and *-KJ600316 stainless steel pipes. The "KJ6278" prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250615017

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15 - 108mm. ½” - 3” BSP (M). ½” - 2” BSP (F).

Marking:

KONJOY, size, WRAS and material grade on fitting body. WRAS, KONJOY, size, material grade, EN10312 and date of manufacture (YYYY/MM) on pipe.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

Adapter 90 with female thread: KJ625015005: 15×Rp½. KJ625018005: 18×Rp½. KJ625022075: 22×Rp¾. Adapter with female thread: KJ627115005: 15×Rp½. KJ627118005: 18×Rp½. KJ627122075: 22×Rp¾. KJ627128001: 28×Rp1. KJ627135125: 35×Rp1¼. KJ627142105: 42×Rp1½. KJ627154002: 54×Rp2. Bridge with plain ending: KJ608500018: 18. KJ608500022: 22. KJ608500028: 28. Cap: KJ621100015: 15. KJ621100018: 18. KJ621100022: 22. KJ621100028: 28. KJ621100035: 35. KJ621100042: 42. KJ621100054: 54. KJ621100076: 76.1. KJ621100089: 88.9. KJ621100108: 108. Elbow 45 with press ending: KJ604500015: 15. KJ604500018: 18. KJ604500015: 22. KJ604500028: 28. KJ604500035: 35. KJ604500042: 42. KJ604500054: 54. KJ604500076: 76.1. KJ604500089: 88.9. KJ604500108: 108. Elbow 45 with plain ending: KJ614500015: 15. KJ614500018: 18. KJ614500022: 22. KJ614500028: 28. KJ614500035: 35. KJ614500042: 4 KJ614500054: 54. KJ614500076: 76.1. KJ614500089: 88.9. KJ614500108 -108. Elbow 90 with press ending KJ609600015: 15. KJ609600018: 18. KJ609600022: 22. KJ609600028: 28. KJ609600035: 35. KJ609600042: 42. KJ609600054: 54. KJ609600067: 66.7. KJ609600076: 76.1. KJ609600089: 88.9. KJ609600108 -108. Elbow 90 with female thread: KJ623015005: 15×Rp½. KJ623018005: 18×Rp½. KJ623022075: 22×Rp¾. KJ623028001: 28×Rp1. KJ623035125 : 35×Rp1¼. KJ623042105: 42×Rp1½. KJ623054002: 54×Rp2. Elbow: 90 with: male thread: KJ624015005: 15×R½. KJ624018005: 18×R½. KJ624022075: 22×R¾ Elbow 90 with plain ending: KJ619100015: 15. KJ619100018: 18. KJ619100022: 22. KJ619100028: 28. KJ619100035: 35. KJ619100042: 42. KJ619100054: 54. KJ619100076: 76.1. KJ619100089: 88.9. KJ619100108: 108. Reducer coupling with plain ending: KJ624301815: 18×15. KJ624302218: 22×18. KJ624302818: 28×18. KJ624303522: 35×22. KJ624303528: 35×28. KJ624304222: 42×22. KJ624304228: 42×28. KJ624304235: 42×35. KJ624305428: 54×28. KJ624305435: 54×35. KJ624305442: 54×42. Reducer coupling with press ending: KJ624401815: 18×15. KJ624402215: 22×15. KJ624402218: 22×18. KJ624402815: 28×15. KJ624402818: 28×18. KJ624402822: 28×22. KJ624403515: 35×15. KJ624403518: 35×18. KJ624403522: 35×22. KJ624403528: 35×28. KJ624404215: 42×15. KJ624404218: 42×18. KJ624404222: 42×22. KJ624404228: 42×28. KJ624404235: 42×35. KJ624405415: 54×15. KJ624405418: 54×18. KJ624405422: 54×22. KJ624405428: 54×28. KJ624405435: 54×35. KJ624405442: 54×42. KJ624406735: 66.7×35. KJ624406754: 66.7×54. KJ624407654: 76.1×54. KJ624408954: 88.9×54. KJ624408976: 88.9×76.1. KJ624410854: 108×54. KJ624410876: 108×76.1. KJ624410889: 108×88.9. Reducer Tee with press ending: KJ613301815: 18×15×18. KJ613302215: 22×15×22. KJ613302218: 22×18×22. KJ613302815: 28×15×28. KJ613302818: 28×18×28. KJ613302822: 28×22×28. KJ613303522: 35×22×35. KJ613303528: 35×28×35. KJ613304222: 42×22×42. KJ613304228: 42×28×42. KJ613304235: 42×35×42. KJ613305422: 54×22×54. KJ613305428: 54×28×54. KJ613305435: 54×35×54. KJ613305442: 54×42×54. KJ613307642: 76.1×42×76.1. KJ613307654: 76.1×54×76.1. KJ613308954: 88.9×54×88.9 KJ613310854: 108×54×108. KJ613310876: 108×76.1×108. KJ613310889: 108×88.9×108 Equal coupling with press ending: KJ623700015: 15. KJ623700018: 18. KJ623700022: 22 KJ623700028: 28. KJ623700035: 35. KJ623700042: 42. KJ623700054: 54. KJ623700067: 66.7. KJ623700076: 76.1. KJ623700089: 88.9. KJ623700108: 108 Adapter with male thread: KJ627215005: 15×R½. KJ627218005: 18×R½. KJ627218075: 18×R¾. KJ627222005: 22×R½. KJ627222075: 22×R¾. KJ627228001: 28×R1. KJ627235125: 35×R1¼. KJ627242105: 42×R1½. KJ627254002: 54×R2. KJ627276205: 76.1×R2½. KJ627289003: 88.9×R3. Slip coupling with press ending: KJ627100015: 15. KJ627100018: 18. KJ627100022: 22. KJ627100028: 28. KJ627100035: 35. KJ627100042: 42 KJ627100054: 54. Tee with press ending: KJ613012015: 15. KJ613012018: 18. KJ613012022: 22. KJ613012028: 28. KJ613012035: 35. KJ613012042: 42. KJ613012054: 54. KJ613012076: 76.1. KJ613012089: 88.9. KJ613012108: 108. Tee with male thread: KJ613815005: 15×R½. KJ613818005: 18×R½. KJ613822005: 22×R½. KJ613822075: 22×R¾. KJ613828005: 28×R½. KJ613828075: 28×R¾. KJ613828001: 28×R1. KJ613835105: 35×R½. KJ613835125: 35×R1¼. KJ613842125: 42×R1¼. KJ613854105: 54×R1½. KJ613854002: 54×R2. Tee with female thread:: KJ613915005: 15×Rp½. KJ613918005: 18×Rp½. KJ613922005: 22×Rp½. KJ613922075: 22×Rp¾. KJ613928005: 28×R½. KJ613928075: 28×Rp¾. KJ613928001: 28×Rp1. KJ613935005: 35×Rp½. KJ613935125: 35×Rp1¼. KJ613942125: 42×Rp1¼. KJ613954105: 54×1½. KJ613954002: 54×Rp2. Adaptor with union nut: KJ627815005: 15×G½. KJ627818005: 18×G½. KJ627818075: 18×G¾. KJ627822005: 22×G½. KJ627822075: 22×G¾. KJ627822001: 22×G1. KJ627828001: 28×G1. KJ627835125: 35×G1¼. KJ627842175: 42×G1¾. KJ627854002: 54×G2. Stainless steel pipe (SS304 or SS316L): *‐KJ600304 (SS304) *-KJ600316 (SS316L) Where * = size in mm between 15 and 108 (in whole numbers: 15, 18, 22, 28, 35, 42, 54, 66.7, 76.1, 88.9, 108).

Approval Holder:

Wenzhou Konjoy Fluid Control Tech Co., Ltd.

Company Name

Wenzhou Konjoy Fluid Control Tech Co., Ltd.

Address

1st Floor, No. 222, Binhai Industrial Zone, 2nd Road, Xinghai Sub‐district, Longwan District, Wenzhou, Zhejiang

Country

China

Phone

0086‐577‐86896059

General Email

info@konjoy‐tech.com

View All Listings by this Company

Uponor S-Press press fittings, Uni-X & Uni-C compression fittings for use with Uponor MLC pipe. Maximum working pressure 10.0 bar, maximum operating temperature 70°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251188701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

14mm

Marking:

Manufacturers name or trademark “U” and size on fitting. Uponor and product info on pipe.

Installation Requirements:

R001

Expiry date:

30/11/2030

Model:

1058085 Uponor Uni-C compression adapter MLC 1013894 UPONOR UNI‐C COUPLING PLATED MLC 1014513 UPONOR S‐PRESS ADAPTER MALE THREAD 1014515 UPONOR S‐PRESS ADAPTER FEMALE THREAD 1014886 UPONOR S‐PRESS TEE 1015154 UPONOR S‐PRESS COUPLING 1015437 Uponor S-Press tap elbow 1133445 Uponor S-Press elbow 1133446 Uponor S-Press tap elbow twin 90deg long 1014654 Uponor SMART AQUA ELBOW ADAPTER S‐PRESS 1014511 UPONOR S‐PRESS ADAPTER 1013366 Uponor Uni Pipe PLUS white 1013577 Uponor Uni Pipe PLUS white insulated 1013678 Uponor Uni Pipe PLUS white in conduit 1160885 Uponor Uni Pipe PLUS white insulated

Approval Holder:

Uponor GmbH

Company Name

Uponor GmbH

Address

Industriestrasse 56, Hassfurt

Postcode

97437,

Country

Germany

Phone

0034916853600

General Email

mariaisabel.fernandez@uponor.com

View All Listings by this Company

Manufacturer:

Uponor GmbH

Company Name

Uponor GmbH

Address

Industriestrasse 56, Hassfurt

Postcode

97437,

Country

Germany

Phone

0034916853600

General Email

mariaisabel.fernandez@uponor.com

View All Listings by this Company

‘Numepress’ range of stainless-steel crimp fittings incorporating EPDM and ‘O’-rings for use with 'Numepress' stainless steel pipe. Connection is achieved via M profile press jaws. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.

Section:

1100 Fittings and Pipe - Compatible Systems

Section Subtitle:

Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251202006

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15, 18, 22, 28, 35, 42, 54, 76, 88, 108, 114, 139 and 168mm crimp. ½”, ¾”, 1”, 1 ¼”, 1 ½”, 2” BSP (M or F – stated via model name). DN50 to DN150 Flanged.

Marking:

ISOTUBI SL LOGO, Numepress and size on fitting body. ISOTUBI, Numepress, size and product info on pipe.

Installation Requirements:

R001

Expiry date:

31/12/2030

Model:

F01 Coupling from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F02 Slip Coupling from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F03 90Q Female-Female Elbow from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F04 90Q Male - Female Elbow from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F05 45Q Female-Female Elbow from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F06 45Q Female - Male Elbow from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F07 Female Angle Adapter from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F08 Male Angle Adapter from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F09 Female Elbow with Wall nut from 15 1/2" to 22 3/4" Material 1.4401/1.4404 & 1.4301/1.4307 F10 90Q Elbow with Plane Ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F11 Valve connector with swivel in stainless Steel from 15 1/2" to 76.121/2" Material 1.4401/1.4404 & 1.4301/1.4307 F12 Female tee threaded adaptor from 15 1/2" to 108 2" Material 1.4401/1.4404 & 1.4301/1.4307 F14 Reducer from 18-15 to 168.3-139.7 Material 1.4401/1.4404 & 1.4301/1.4307 F15 Reducing tee from 18-15 to 168.3-139.7 Material 1.4401/1.4404 & 1.4301/1.4307 F16 Equal Tee from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F17 Female adaptor from 15 3/ 8" to 88.9 3" Material 1.4401/1.4404 & 1.4301/1.4307 F18 M ale adaptor from 15 3/8" to 108 4" Material 1.4401/1.4404 & 1.4301/1.4307 F19 Flanges adaptor from 15 DN15 to 108 DN100 Material 1.4401/1.4404 & 1.4301/1.4307 F20 Pre-formed pipe bridge from 15 to 28 Material 1.4401/1.4404 & 1.4301/1.4307 F21 Plug from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F22 Air tuve Pipe Bridge from 15 to 28 Material 1.4401/1.4404 & 1.4301/1.4307 F23 Pipe Bridge from 15 to 28 Material 1.4401/1.4404 & 1.4301/1.4307 F24 3 Pieces adaptor from 15 to 60.3 Material 1.4401/1.4404 & 1.4301/1.4307 F25 Female -Female pipe bridge from 15 to 28 Material 1.4401/1.4404 & 1.4301/1.4307 F26 Female connector from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F27 Male connector from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F28 Press flanged adaptor from 54 DN50 to 168.3 DN150 Material 1.4401/1.4404 & 1.4301/1.4307 F30 Cross or reduced cross from 15-15-15-15 to 168.3-168.3-168.3-168 .3 Material 1.4401/1.4404 & 1.4301/1.4307 F33 45Q Male angle adaptor from 15 1/ 2" to 28 1" Material 1.4401/1.4404 & 1.4301/1.4307 F34 90Q Female angle adaptor 15 3/ 8" to 35 1 1/ 4" Material 1.4401/1.4404 & 1.4301/1.4307 F35 90Q Female angle adaptor with swivel nut from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F36 Male Tee threaded adaptor from 15 3/8" to 35 11/4" Material 1.4401/1.4404 & 1.4301/1.4307 F37 Male threaded cross from 15 1/2" to 108-4" Material 1.4401/1.4404 & 1.4301/1.4307 F38 Female threaded cross from 15 1/ 2" to 108 4" Material 1.4401/1.4404 & 1.4301/1.4307 F39 90Q Male angle adaptor from 15 3/8" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F41 Male union connector gas from 15 1/ 2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F42 Female Union connector gas from 15 1/2" to 54 2" Material 1.4401/1.4404 & 1.4301/1.4307 F43 Grooved Transition from 3/4" to 2" Material 1.4401/1.4404 & 1.4301/1.4307 F44 Van Stone flange from 1/2" to 2" Material 1.4401/1.4404 & 1.4301/1.4307 F45 Union Gas Female threaded from 15 3/4" to 54 2"Material 1.4401/1.4404 & 1.4301/1.4307 F46 Straight union with press fitting on both ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F47 Half coupling from 15 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F48 30Q Female-Female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F49 30Q Elbow with plain ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F50 15Q Female-female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F51 60Q Female-female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F52 Flanges adaptor PN6 from 15 DN15 to 108 DN100 Material 1.4401/1.4404 & 1.4301/1.4307 F53 Pipe penetration from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F54 Male plug from 16 to 168.3 Material 1.4401/1.4404 & 1.4301/1.4307 F55 Weld Adaptor from 15 to 60.3 Material 1.4401/1.4404 & 1.4301/1.4307 F56 75Q Female -Female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F57 l0Q Female-Female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F58 60Q Elbow with plain ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F59 lSQ Elbow with plain ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F60 Slip coupling with female thread from DN15 1/ 2" to DN54 Material 1.4401/1.4404 & 1.4301/1.4307 F61 Transition for grooved coupling from DN28x33.7 to DN108x 11 4.3 Material 1.4401/1.4404 & 1.4301/1.4307 F63 7SQ Elbow with plain ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 F64 15Q Male -female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F65 Male-Female pipe penetration from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F66 30Q Male-female elbow from 15 to 108 Material 1.4401/1.4404 & 1.4301/1.4307 F72 45Q Elbow with plain ends from 15 to 54 Material 1.4401/1.4404 & 1.4301/1.4307 Pipe 15 x 0.6 mm Material 1.4401/1.4404 Pipe 18 x 0.7 mm Material 1.4401/1.4404 Pipe 22 x 0.7 mm Material 1.4401/1.4404 Pipe 28 x 0.8 mm Material 1.4401/1.4404 Pipe 35 x 1 mm Material 1.4401/1.4404 Pipe 42 x 1.1 mm Material 1.4401/1.4404 Pipe 54 x 1.2 mm Material 1.4401/1.4404 Pipe 76.1 x 1.5 mm Material 1.4 401/ 1.4404 Pipe 15 x 1 mm Material 1.4401/1.4404 Pipe 18 x 1 mm Material 1.4401/1.4404 Pipe 22 x 1.2 mm Material 1.4401/1.4404 Pipe 28 x 1.2 mm Material 1.4401/1.4404 Pipe 35 x 1.5 mm Material 1.4401/1.4404 Pipe 42 x 1.5 mm Material 1.4401/1.4404 Pipe 54 x 1.5 mm Material 1.4401/1.4404 Pipe 76.1 x 2 mm Material 1.4401/1.4404 Pipe 88.9 x 2 mm Material 1.4401/1.4404 Pipe 114.3 x 2 mm Material 1.4401/1.4404 Pipe 139.7 x 2 mm Material 1.4401/1.4404 Pipe 139.7 x 2.6 mm Material 1.4401/1.4404 Pipe 168.3 x 2 mm Material 1.4401/1.4404 Pipe 168.3 x 2.6 mm Material 1.4401/1.4404 Pipe 15 x 0.6 mm Material 1.4301/1.4307 Pipe 18 x 0.7 mm Material 1.4301/1.4307 Pipe 22 x 0.7 mm Material 1.4301/1.4307 Pipe 28 x 0.8 mm Material 1.4301/1.4307 Pipe 35 x 1 mm Material 1.4301/1.4307 Pipe 42 x 1.1 mm Material 1.4301/1.4307 Pipe 54 x 1 .2 mm, Material 1.4301/1.4307 Pipe 76.1 x 1.5 mm Material 1.4301/1.4307 Pipe 15 x 1 mm Material 1.4301/1.4307 Pipe 18 x 1 mm Material 1.4301/1.4307 Pipe 22 x 1. 2 mm Material 1.4301/1.4307 Pipe 28 x 1.2 mm Material 1.4301/1.4307 Pipe 35 x 1.5 mm Material 1.4301/1.4307 Pipe 42 x 1.5 mm Material 1.4301/1.4307 Pipe 54 x 1.5 mm Material 1.4301/1.4307 Pipe 76.1 x 2 mm Material 1.4301/1.4307 Pipe 88.9 x 2 mm Material 1.4301/1.4307 Pipe 108 x 2 mm Material 1.4301/1.4307 Pipe 114.3 x 2 mm Material 1.4301/1.4307 Pipe 139.7 x 2 mm Material 1.4301/1.4307 Pipe 139.7 x 2.6 mm Material 1.4301/1 .4307 Pipe 168.3 x 2 mm Material 1.4301/1.4307 Pipe 168.3 x 2.6 mm Material 1.4301/1.4307

Product Images

Approval Holder:

ISOTUBI SL

Company Name

ISOTUBI SL

Address

Pol. Ind. Santa Rita c/ Mecànica 6 08755 Castellbisbal ( Bcn ) SPAIN

Country

Spain

General Email

xavi.armengou@isotubi.com

View All Listings by this Company

Manufacturer:

ISOTUBI SL

Company Name

ISOTUBI SL

Address

Pol. Ind. Santa Rita c/ Mecànica 6 08755 Castellbisbal ( Bcn ) SPAIN

Country

Spain

General Email

xavi.armengou@isotubi.com

View All Listings by this Company

‘Fastwarm’ range of U profile press fittings (nickel plated brass bodies) for use with ‘Fastwarm’ range of PERT/AL/PERT multi-layered pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1106 Multi-Layered Pipe Systems: incorporating an Aluminium layer

Section Subtitle:

Compatible fittings and pipe systems. Unless specified in the individual approval, the products within this section are not suitable for below ground use Because there are no accepted tests, WRAS approval of barrier pipe does not include an assessment of its ability to prevent migration of contaminants through the wall of the pipe from the surrounding soil.

WRAS Approval Number:

240704745

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

16mm – 32mm

Marking:

Fastwarm on body Fastwarm, size, WRAS and product info on pipe.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

Equal Straight Union FW-KY101-S1616 S16X16 FW-KY101-S2020 S20X20 FW-KY101-S2525 S25X25 FW-KY101-S3232 S32X32 Unequal Straight Union FW-KY102-S2016 S20X16 FW-KY102-S2516 S25X16 FW-KY102-S2520 S25X20 FW-KY102-S3216 S32X16 FW-KY102-S3220 S32X20 FW-KY102-S3225 S32X25 Male Straight Union FW-KY103-S1612M S 16X1/2M FW-KY103-S1634M S 16X3/4M FW-KY103-S2012M S 20X1/2M FW-KY103-S2034M S 20X3/4M FW-KY103-S2512M S 25X1/2M FW-KY103-S2534M S 25X3/4M FW-KY103-S2511M S25X1M FW-KY103-S3234M S 32X3/4M FW-KY103-S3211M S 32X1M Female Straight Union FW-KY104-S1612F S 16X1/2 F FW-KY104-S1634F S 16X3/4 F FW-KY104-S2012F S 20X1/2 F FW-KY104-S2034F S 20X3/4 F FW-KY104-S2534F S 25X3/4 F FW-KY104-S2511F S 25X1 F FW-KY104-S3234F S 32X3/4 F FW-KY104-S3211F S 32X1 F Swivel Coupling FW-KY105-1612F 16X1/2F FW-KY105-2034F 20X3/4F FW-KY105-2012F 20X1/2F FW-KY105-2534F 25X3/4F Equal Elbow FW-KY106-L1616 L 16X16 FW-KY106-L2020 L 20X20 FW-KY106-L2525 L 25X25 FW-KY106-L3232 L 32X32 Female Elbow FW-KY107-L1612F L 16X1/2 F FW-KY107-L1634F L 16X3/4 F FW-KY107-L2012F L 20X1/2 F FW-KY107-L2034F L 20X3/4 F FW-KY107-L2534F L 25X3/4 F FW-KY107-L2511F L 25X1 F FW-KY107-L3211F L 32X1 F Male Elbow FW-KY108-L1612M L16x1/2M FW-KY108-L2012M L20x1/2M FW-KY108-L2034M L20X3/4M FW-KY108-L2534M L25x3/4M FW-KY108-L3211M L32x1M Swivel Elbow FW-KY109-1612F 16X1/2F FW-KY109-2034F 20X3/4F Equal Tee FW-KY110-T161616 T 16X16X16 FW-KY110-T202020 T 20X20X20 FW-KY110-T252525 T 25X25X25 FW-KY110-T323232 T 32X32X32 Unequal Tee FW-KY111-T162016 T 16X20X16 FW-KY111-T201616 T 20X16X16 FW-KY111-T201620 T20X16X20 FW-KY111-T202016 T20X20X16 FW-KY111-T251625 T 25X16X25 FW-KY111-T252516 T 25X25X16 FW-KY111-T251616 T25X16X16 FW-KY111-T252020 T 25X20X20 FW-KY111-T252025 T 25X20X25 FW-KY111-T321632 T32X16X32 FW-KY111-T322032 T32X20X32 FW-KY111-T322525 T32X25X25 FW-KY111-T322532 T32X25X32 Female Tee FW112-T2512F25 T25X1/2FX25 Elbow With Plate-Male FW-KY114-1612M 16X1/2M FW-KY114-1634M 16X3/4 M FW-KY114-2034M 20X3/4 M Elbow with Plate-Female FW-KY115-1612F 16X1/2 F FW-KY115-1634F 16X3/4F FW-KY115-2012F 20X1/2F FW-KY115-2034F 20X3/4F End cap FW-KY116-16 16 FW-KY116-20 20 FW-KY116-25 25 ‘ZL' range of PERT/AL/PERT multi-layer pipes. PERTPIPE50M 16*2.0 PERTPIPE60M 16*2.0 PERTPIPE70M 16*2.0 PERTPIPE 80M 16*2.0 PERTPIPE90M 16*2.0 PERTPIPE100M 16*2.0 PERTPIPE110M 16*2.0 PERTPIPE120M 16*2.0 PERTPIPE150M 16*2.0 PERTPIPE200M 16*2.0

Approval Holder:

Fastwarm Limited

Company Name

Fastwarm Limited

Address

Unit 13 Carnival Park Basildon Essex

Postcode

SS14 3WN

Phone

01228 744 479

General Email

support@fastwarm.com

View All Listings by this Company

Range of ‘M’ profile copper press fittings with EPDM ‘O’-rings for use with copper pipes (manufactured to EN 1057). Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251015011

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Linhai Hengye Tubing Equipment Co., Ltd logo (‘IoJ’) and size on body.

Installation Requirements:

R001

Expiry date:

31/10/2030

Model:

P5270 series - Coupling: P527012: 12mm, P527015: 15mm, P527018: 18mm, P527022: 22mm, P527028: 28mm, P527035: 35mm, P527042: 42mm, P527054: 54mm. P5270S series - Slip coupling: P5270S12: 12mm, P5270S15: 15mm, P5270S18: 18mm, P5270S22: 22mm, P5270S28: 28mm, P5270S35: 35mm, P5270S42: 42mm, P5270S54: 54mm. P5240 series - Reducing coupling: P52402215: 22x15mm, P52402815: 28x15mm, P52402822: 28x22mm, P52403515: 35x15mm, P52403522: 35x22mm, P52403528: 35x28mm, P52404222: 42x22mm, P52404228: 42x28mm, P52404235: 42x35mm, P52405428: 54x28mm, P52405435: 54x35mm, P52405442: 54x42mm. P5243 series - Fitting Reducer: P52431512: 15x12mm, P52431812: 18x12mm, P52431815: 18x15mm, P52432215: 22x15mm, P52432218: 22x18mm, P52432815: 28x15mm, P52432818: 28x18mm, P52432822: 28x22mm, P52433515: 35x15mm, P52433518: 35x18mm, P52433522: 35x22mm, P52433528: 35x28mm, P52434215: 42x15mm, P52434218: 42x18mm, P52434222: 42x22mm, P52434228: 42x28mm, P52434235: 42x35mm, P52435415: 54x15mm, P52435418: 54x18mm, P52435422: 54x22mm, P52435428: 54x28mm, P52435435: 54x35mm, P52435442: 54x42mm. P5090 series - Reducing elbow 90°: P50902215: 22x15mm, P50902815: 28x15mm, P50902822: 28x22mm. P5085 series - Full Crossover: P508515: 15mm, P508522: 22mm. P5086 series - Part Crossover: P508615: 15mm, P508622: 22mm. P5090 series - Elbow 90°: P509012: 12mm, P509015: 15mm, P509018: 18mm, P509022: 22mm, P509028: 28mm, P509035: 35mm, P509042: 42mm, P509054: 54mm. P5092 series - Street elbow 90°: P509212: 12mm, P509215: 15mm, P509218: 18mm, P509222: 22mm, P509228: 28mm, P509235: 35mm, P509242: 42mm, P509254: 54mm. P5041 series - Elbow 45°: P504112: 12mm, P504115: 15mm, P504118: 18mm, P504122: 22mm, P504128: 28mm, P504135: 35mm, P504142: 42mm, P504154: 54mm. P5040 series - Street elbow 45°: P504012: 12mm, P504015: 15mm, P504018: 18mm, P504022: 22mm, P504028: 28mm, P504035: 35mm, P504042: 42mm, P504054: 54mm. P5130 series - Equal tee: P513012: 12mm, P513015: 15mm, P513018: 18mm, P513022: 22mm, P513028: 28mm, P513035: 35mm, P513042: 42mm, P513054: 54mm. P5130 series - Reducing tee: P5130151212: 15x12x12mm, P5130151215: 15x12x15mm, P5130151815: 15x18x15mm, P5130152215: 15x22x15mm, P5130181218: 18x12x18mm, P5130181515: 18x15x15mm, P5130181518: 18x15x18mm, P5130181815: 18x18x15mm, P5130221222: 22x12x22mm, P5130221522: 22x15x22mm, P5130221822: 22x18x22mm, P5130221515: 22x15x15mm, P5130222215: 22x22x15mm, P5130281528: 28x15x28mm, P5130281828: 28x18x28mm, P5130282228: 28x22x28mm, P5130351535: 35x15x35mm, P5130351835: 35x18x35mm, P5130352235: 35x22x35mm, P5130352835: 35x28x35mm, P5130351515: 35x15x15mm, P5130351518: 35x15x18mm, P5130351522: 35x15x22mm, P5130351528: 35x15x28mm, P5130351815: 35x18x15mm, P5130351818: 35x18x18mm, P5130351822: 35x18x22mm, P5130351828: 35x18x28mm, P5130352215: 35x22x15mm, P5130352218: 35x22x18mm, P5130352222: 35x22x22mm, P5130352228: 35x22x28mm, P5130352815: 35x28x15mm, P5130352818: 35x28x18mm, P5130352822: 35x28x22mm, P5130352828: 35x28x28mm, P5130353515: 35x35x15mm, P5130353518: 35x35x18mm, P5130353522: 35x35x22mm, P5130353528: 35x35x28mm, P5130421542: 42x15x42mm, P5130421842: 42x18x42mm, P5130422242: 42x22x42mm, P5130422842: 42x28x42mm, P5130423542: 42x35x42mm, P5130421515: 42x15x15mm, P5130421518: 42x15x18mm, P5130421522: 42x15x22mm, P5130421528: 42x15x28mm, P5130421535: 42x15x35mm, P5130421815: 42x18x15mm, P5130421818: 42x18x18mm, P5130421822: 42x18x22mm, P5130421828: 42x18x28mm, P5130421835: 42x18x35mm, P5130422215: 42x22x15mm, P5130422218: 42x22x18mm, P5130422222: 42x22x22mm, P5130422228: 42x22x28mm, P5130422235: 42x22x35mm, P5130422815: 42x28x15mm, P5130422818: 42x28x18mm, P5130422822: 42x28x22mm, P5130422828: 42x28x28mm, P5130422835: 42x28x35mm, P5130423515: 42x35x15mm, P5130423518: 42x35x18mm, P5130423522: 42x35x22mm, P5130423528: 42x35x28mm, P5130423535: 42x35x35mm, P5130424215: 42x42x15mm, P5130424218: 42x42x18mm, P5130424222: 42x42x22mm, P5130424228: 42x42x28mm, P5130424235: 42x42x35mm, P5130541554: 54x15x54mm, P5130541854: 54x18x54mm, P5130542254: 54x22x54mm, P5130542854: 54x28x54mm, P5130543554: 54x35x54mm, P5130544254: 54x42x54mm, P5130541515: 54x15x15mm, P5130541518: 54x15x18mm, P5130541522: 54x15x22mm, P5130541528: 54x15x28mm, P5130541535: 54x15x35mm, P5130541542: 54x15x42mm, P5130541815: 54x18x15mm, P5130541818: 54x18x18mm, P5130541822: 54x18x22mm, P5130541828: 54x18x28mm, P5130541835: 54x18x35mm, P5130541842: 54x18x42mm, P5130542215: 54x22x15mm, P5130542218: 54x22x18mm, P5130542222: 54x22x22mm, P5130542228: 54x22x28mm, P5130542235: 54x22x35mm, P5130542242: 54x22x42mm, P5130542815: 54x28x15mm, P5130542818: 54x28x18mm, P5130542822: 54x28x22mm, P5130542828: 54x28x28mm, P5130542835: 54x28x35mm, P5130542842: 54x28x42mm, P5130543515: 54x35x15mm, P5130543518: 54x35x18mm, P5130543522: 54x35x22mm, P5130543528: 54x35x28mm, P5130543535: 54x35x35mm, P5130543542: 54x35x42mm, P5130544215: 54x42x15mm, P5130544218: 54x42x18mm, P5130544222: 54x42x22mm, P5130544228: 54x42x28mm, P5130544235: 54x42x35mm, P5130544242: 54x42x42mm, P5130545415: 54x54x15mm, P5130545418: 54x54x18mm, P5130545422: 54x54x22mm, P5130545428: 54x54x28mm, P5130545435: 54x54x35mm, P5130545442: 54x54x42mm. P5301 series - End cap: P530112: 12mm, P530115: 15mm, P530118: 18mm, P530122: 22mm, P530128: 28mm, P530135: 35mm, P530142: 42mm, P530154: 54mm.

Approval Holder:

Linhai Hengye Tubing Equipment Co., Ltd

Company Name

Linhai Hengye Tubing Equipment Co., Ltd

Address

Machinery Industrial Park, Duqiao Town, Linhai City

Country

China

Phone

0086‐576‐85528079

General Email

sales@zjhengye.com

View All Listings by this Company

Manufacturer:

Linhai Hengye Tubing Equipment Co., Ltd

Company Name

Linhai Hengye Tubing Equipment Co., Ltd

Address

Machinery Industrial Park, Duqiao Town, Linhai City

Country

China

Phone

0086‐576‐85528079

General Email

sales@zjhengye.com

View All Listings by this Company

'Flomasta’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250602053

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

10mm, 15mm, 22mm, 28mm

Marking:

TLC (TwistLoc logo) and size on body

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

‘Flomasta’ range comprising of models: SRDE6764M 15mmX1/2"BSP DROP EAR ELBOW SRF6764M 15mmX1/2"BSP FEMALE ADAPTOR SRF6765M 15mmX3/4"BSP FEMALE ADAPTOR SRF6745M 22mmX3/4"BSP FEMALE ADAPTOR SRF6701M 28mmX1"BSP FEMALE ADAPTOR SPU6711M 10mm STR UNION SPU6766M 15mm STR UNION SPU6744M 22mm STR UNION SPU6700M 28mm STR UNION SPU6761M 15mmX10mm REDUCING STR UNION SPU6746M 22mmX15mm REDUCING STR UNION SRSE6714M 10mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6764M 15mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6765M 15mmX3/4"BSP SWIVEL ELBOW (Hand Tighten) SRSE6714BM 10mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6764BM 15mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6765BM 15mmX3/4"BSP SWIVEL ELBOW (Brass Nut) SPSU6714M 10mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6764M 15mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6765M 15mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6745M 22mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6714BM 10mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6764BM 15mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6765BM 15mmX3/4"BSP SWIVEL UNION (Brass Nut) SPSU6745BM 22mmX3/4"BSP SWIVEL UNION (Brass Nut) SPST671M 10mm END STOP SPST676M 15mm END STOP SPST674M 22mm END STOP SRST670M 28mm END STOP SPE6711M 10mm ELBOW SPE6766M 15mm ELBOW SPE6744M 22mm ELBOW SPE6700M 28mm ELBOW SPE6761M 15mmX10mm REDUCING ELBOW SPE6746M 22mmX15mm REDUCING ELBOW SPATE6766M 15mm-135o STEM ELBOW SPATE6744M 22mm-135o STEM ELBOW SPR6716M 10mmX15mm REDUCER SPR6764M 15mmX22mm REDUCER SPR6760M 15mmX28mm REDUCER SPR6740M 22mmX28mm REDUCER SPT67111M 10mm TEE SPT67666M 15mm TEE SPT67444M 22mm TEE SPT67000M 28mm TEE SPT67611M 15mmX10mmX10mm REDUCING TEE SPT67661M 15mmX15mmX10mm REDUCING TEE SPT67664M 15mmX15mmX22mm REDUCING TEE SPT67466M 22mmX15mmX15mm REDUCING TEE SPT67464M 22mmx15mmx22mm REDUCING TEE SPT67441M 22mmx22mmx10mm REDUCING TEE SPT67446M 22mmX22mmX15mm REDUCING TEE SPT67044M 28mmX22mmX22mm REDUCING TEE SPT67040M 28mmX22mmX28mm REDUCING TEE SPT67001M 28mmX28mmX10mm REDUCING TEE SPT67006M 28mmX28mmX15mm REDUCING TEE SPT67004M 28mmX28mmX22mm REDUCING TEE SPTT67441M 22mX22mmX10mm TUBE TEE SPTT67446M 22mX22mmX15mm TUBE TEE SPTE6711M 10mm TUBE ELBOW SPTE6716M 10mmx15mm TUBE ELBOW SPTE6766M 15mm TUBE ELBOW SPTE6744M 22mm TUBE ELBOW SRMC6764M 15mmX1/2"BSPT MALE CONNECTOR SRME6764M 15mmX1/2"BSPT MALE ELBOW SRFWC6741M 22mmX10mm 4WAY MANIFOLD SRU6766SM 15mm SLIP UNION SRU6744SM 22mm SLIP UNION STS10M 10mm PIPE INSERT STS15M 15mm PIPE INSERT STS22M 22mm PIPE INSERT STS28M 28mm PIPE INSERT SRAV63M 15mm AIR-VENT CONNECTOR

Approval Holder:

Kingfisher International Products Ltd

Company Name

Kingfisher International Products Ltd

Address

1 Paddington Square, London

Postcode

W2 1GG

Phone

07721 260713

General Email

eric.capotummino@kingfisher.com

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

General Email

nchoi@twistloc.com

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

General Email

nchoi@twistloc.com

View All Listings by this Company

RWC range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

2207410

Note:

For above and below ground use

Size:

20mm – 63mm.

Marking:

JG logo, John Guest, size & PN on compression nut.

Installation Requirements:

R001

Expiry date:

31/07/2027

Model:

Reducing Tee (Branch Reduced) RWC UGCF30A252520: JG MDPE Compression Red Tee - 25 x 25 x 20mm UGCF30A323225: JG MDPE Compression Red Tee - 32 x 32 x 25mm UGCF30A404032: JG MDPE Compression Red Tee - 40 x 40 x 32mm UGCF30A505025: JG MDPE Compression Red Tee - 50 x 50 x 25mm UGCF30A505032: JG MDPE Compression Red Tee - 50 x 50 x 32mm UGCF30A505040: JG MDPE Compression Red Tee - 50 x 50 x 40mm UGCF30A636332: JG MDPE Compression Red Tee - 63 x 63 x 32mm UGCF30A636340: JG MDPE Compression Red Tee - 63 x 63 x 40mm UGCF30A636350: JG MDPE Compression Red Tee - 63 x 63 x 50mm Male Thread Adaptor RWC UGCF45M2012BSP: JG MDPE Compression Male Adpt - 20mm x 1/2" UGCF45M2034BSP: JG MDPE Compression Male Adpt - 20mm x 3/4" UGCF45M2512BSP: JG MDPE Compression Male Adpt - 25mm x 1/2" UGCF45M2534BSP: JG MDPE Compression Male Adpt - 25mm x 3/4" UGCF45M251BSP: JG MDPE Compression Male Adpt - 25mm x 1" UGCF45M3234BSP: JG MDPE Compression Male Adpt - 32mm x 3/4" UGCF45M321BSP: JG MDPE Compression Male Adpt - 32mm x 1" UGCF45M32114BSP: JG MDPE Compression Male Adpt - 32mm x 1-1/4" UGCF45M32112BSP: JG MDPE Compression Male Adpt - 32mm x 1-1/2" UGCF45M401BSP: JG MDPE Compression Male Adpt - 40mm x 1" UGCF45M40114BSP: JG MDPE Compression Male Adpt - 40mm x 1-1/4" UGCF45M40112BSP: JG MDPE Compression Male Adpt - 40mm x 1-1/2" UGCF45M50112BSP: JG MDPE Compression Male Adpt - 50mm x 1-1/2" UGCF45M502BSP: JG MDPE Compression Male Adpt - 50mm x 2" UGCF45M63112BSP: JG MDPE Compression Male Adpt - 63mm x 1-1/2" UGCF45M632BSP: JG MDPE Compression Male Adpt - 63mm x 2" Female Threaded Branch Tee RWC UGCF58F202012BSP: JG MDPE Compression Fem Tee - 20 x 20 x 1/2" UGCF58F202034BSP: JG MDPE Compression Fem Tee - 20 x 20 x 3/4" UGCF58F252512BSP: JG MDPE Compression Fem Tee - 25 x 25 x 1/2" UGCF58F252534BSP: JG MDPE Compression Fem Tee - 25 x 25 x 3/4" UGCF58F323234BSP: JG MDPE Compression Fem Tee - 32 x 32 x 3/4" UGCF58F32321BSP: JG MDPE Compression Fem Tee - 32 x 32 x 1" UGCF58F4040114BSP: JG MDPE Compression Fem Tee - 40 x 40 x 1-1/4" UGCF58F4040112BSP: JG MDPE Compression Fem Tee - 40 x 40 x 1-1/2" UGCF58F5050112BSP: JG MDPE Compression Fem Tee - 50 x 50 x 1-1/2" UGCF58F50502BSP: JG MDPE Compression Fem Tee - 50 x 50 x 2" UGCF58F63632BSP: JG MDPE Compression Fem Tee - 63 x 63 x 2" Female Thread Adaptor RWC UGCF45F2012BSP: JG MDPE Compression Female Adpt - 20mm x 1/2" UGCF45F2034BSP: JG MDPE Compression Female Adpt - 20mm x 3/4" UGCF45F2512BSP: JG MDPE Compression Female Adpt - 25mm x 1/2" UGCF45F2534BSP: JG MDPE Compression Female Adpt - 25mm x 3/4" UGCF45F251BSP: JG MDPE Compression Female Adpt - 25mm x 1" UGCF45F3234BSP: JG MDPE Compression Female Adpt - 32mm x 3/4" UGCF45F321BSP: JG MDPE Compression Female Adpt - 32mm x 1" UGCF45F32114BSP: JG MDPE Compression Female Adpt - 32mm x 1-1/4" UGCF45F32112BSP: JG MDPE Compression Female Adpt - 32mm x 1-1/2" UGCF45F401BSP: JG MDPE Compression Female Adpt - 40mm x 1" UGCF45F40114BSP: JG MDPE Compression Female Adpt - 40mm x 1-1/4" UGCF45F40112BSP: JG MDPE Compression Female Adpt - 40mm x 1-1/2" UGCF45F50112BSP: JG MDPE Compression Female Adpt - 50mm x 1-1/2" UGCF45F502BSP: JG MDPE Compression Female Adpt - 50mm x 2" UGCF45F63112BSP: JG MDPE Compression Female Adpt - 63mm x 1-1/2" UGCF45F632BSP: JG MDPE Compression Female Adpt - 63mm x 2" Stop End RWC UGCF4620: JG MDPE Compression Stop End - 20mm UGCF4625: JG MDPE Compression Stop End - 25mm UGCF4632: JG MDPE Compression Stop End - 32mm UGCF4640: JG MDPE Compression Stop End - 40mm UGCF4650: JG MDPE Compression Stop End - 50mm UGCF4663: JG MDPE Compression Stop End - 63mm Straight Coupling RWC UGCF0420: JG MDPE Compression Straight Coupling - 20mm UGCF0425: JG MDPE Compression Straight Coupling - 25mm UGCF0432: JG MDPE Compression Straight Coupling - 32mm UGCF0440: JG MDPE Compression Straight Coupling - 40mm UGCF0450: JG MDPE Compression Straight Coupling - 50mm UGCF0463: JG MDPE Compression Straight Coupling - 63mm Reducing Coupling RWC UGCF202520: JG MDPE Compression Red Coupling - 25 x 20mm UGCF203220: JG MDPE Compression Red Coupling - 32 x 20mm UGCF203225: JG MDPE Compression Red Coupling - 32 x 25mm UGCF204025: JG MDPE Compression Red Coupling - 40 x 25mm UGCF204032: JG MDPE Compression Red Coupling - 40 x 32mm UGCF205025: JG MDPE Compression Red Coupling - 50 x 25mm UGCF205032: JG MDPE Compression Red Coupling - 50 x 32mm UGCF205040: JG MDPE Compression Red Coupling - 50 x 40mm UGCF206332: JG MDPE Compression Red Coupling - 63 x 32mm UGCF206340: JG MDPE Compression Red Coupling - 63 x 40mm UGCF206350: JG MDPE Compression Red Coupling - 63 x 50mm Elbow - 90 Degree RWC UGCF0320: JG MDPE Compression Elbow - 90D - 20mm UGCF0325: JG MDPE Compression Elbow - 90D - 25mm UGCF0332: JG MDPE Compression Elbow - 90D - 32mm UGCF0340: JG MDPE Compression Elbow - 90D - 40mm UGCF0350: JG MDPE Compression Elbow - 90D - 50mm UGCF0363: JG MDPE Compression Elbow - 90D - 63mm Male Threaded Elbow RWC UGCF75M2534BSP: JG MDPE Compression Male Elbow - 25mm x 3/4" UGCF75M321BSP: JG MDPE Compression Male Elbow - 32mm x 1" Female Threaded Elbow RWC UGCF75F2012BSP: JG MDPE Compression Fem Elbow - 20mm x 1/2" UGCF75F2034BSP: JG MDPE Compression Fem Elbow - 20mm x 3/4" UGCF75F2512BSP: JG MDPE Compression Fem Elbow - 25mm x 1/2" UGCF75F2534BSP: JG MDPE Compression Fem Elbow - 25mm x 3/4" UGCF75F251BSP: JG MDPE Compression Fem Elbow - 25mm x 1" UGCF75F321BSP: JG MDPE Compression Fem Elbow - 32mm x 1" UGCF75F40114BSP: JG MDPE Compression Fem Elbow - 40mm x 1-1/4" UGCF75F40112BSP: JG MDPE Compression Fem Elbow - 40mm x 1-1/2" UGCF75F50112BSP: JG MDPE Compression Fem Elbow - 50mm x 1-1/2" UGCF75F632BSP: JG MDPE Compression Fem Elbow - 63mm x 2" Wall Plate Elbow (PP) RWC UGCF88WB2012BSP: JG MDPE Compression Wall Elbow - 20mm x 1/2" UGCF88WB2534BSP: JG MDPE Compression Wall Elbow - 25mm x 3/4" Equal Tee RWC UGCF0220: JG MDPE Compression Equal Tee - 20mm UGCF0225: JG MDPE Compression Equal Tee - 25mm UGCF0232: JG MDPE Compression Equal Tee - 32mm UGCF0240: JG MDPE Compression Equal Tee - 40mm UGCF0250: JG MDPE Compression Equal Tee - 50mm UGCF0263: JG MDPE Compression Equal Tee - 63mm Repair Coupling RWC UGCF04R25: JG MDPE Compression Repair Coupling - 25mm UGCF04R32: JG MDPE Compression Repair Coupling - 32mm UGCF04R40: JG MDPE Compression Repair Coupling - 40mm UGCF04R50: JG MDPE Compression Repair Coupling - 50mm UGCF04R63: JG MDPE Compression Repair Coupling - 63mm Conversion Adaptor - MPDE to Copper (Pushfit) RWC UGCF01PF2522: JG MDPE Compression Conversion Adpt - 25 x 22mm UGCF01PF3222: JG MDPE Compression Conversion Adpt - 32 x 22mm UGCF01PF3228: JG MDPE Compression Conversion Adpt - 32 x 28mm Models added September 2025 UGCF75F321BSP ELBOW THREADED FEMALE 32 X 1" UGCF30A505032 TEE REDUCING 50X32X50 Models added January 2026 UGCF01IMP2012BSP - Coupling 1/2"x20 UGCF01IMP2512BSP - Coupling 1/2"x25 UGCF01IMP2534BSP - Coupling 3/4"x25 UGCF0316: ELBOW - 90 DEGREE 16X16 UGCF0216: EQUAL TEE 16X16X16 UGCF30A202016: TEE REDUCING 20X16X20 UGCF4616: END PLUG 16MM UGCF0416: COUPLING 16X16 UGCF202016: REDUCING COUPLING 20X16 UGCF202516: REDUCING COUPLING 25X16 UGCF01PF2015: UNIVERSAL FITTING - CONVERSION REDUCER 20X15 UGCF01PF2515: UNIVERSAL FITTING - CONVERSION REDUCER 25X15 UGCF45M1612BSP: ADAPTOR MALE 16X UGCF45M1634BSP: ADAPTOR MALE 16X UGCF45F1612BSP: ADAPTOR FEMALE 16X 1/2’’ UGCF45F1634BSP: ADAPTOR FEMALE 16X 3/4’’

Approval Holder:

Reliance Worldwide Corporation (UK)

Company Name

Reliance Worldwide Corporation (UK)

Address

Horton Road, West Drayton

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Range of brass press fittings with EPDM ‘O’-rings for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). Jointing is achieved via a crimping tool using either a ‘U’, ‘TH’ or ‘H’ profile. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251115002

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Equal Straight Union: 16mm - 32mm, Unequal Straight Union: 20mmx16mm - 32mmx26mm, Male Straight Union: 16mmx⅜” BSP (M) - 32mmx1” BSP (M), Female Straight Union: 16mmx⅜” BSP (F) - 32mmx1” BSP (F), Equal Elbows: 16mm - 32mm, Male Elbows: 16mmx⅜” BSP (M) - 32mmx1” BSP (M), Female Elbows: 16mmx⅜ BSP (F) - 32mmx1” BSP (F), Equal Tees: 16mm - 32mm, Unequal Tees: 16mmx20mmx16mm - 32mmx26mmx32mm, Female Tee: 16mmx16mmx⅜” BSP (F) - 32mmx32mmx1” BSP (F), Wall-plated female elbow: 16mmx⅜” BSP (F) - 26mmx¾” BSP (F),

Marking:

Brymec & arrow logo, size, crimp profile (U-TH-H) and production date (MM/YYYY) on crimp sleeve.

Installation Requirements:

R001

Expiry date:

30/11/2030

Model:

Equal Straight Union (16mm - 32mm): 51019 ∙ 16mm Brass Coupler Multilayer Crimp Fitting 51020 ∙ 20mm Brass Coupler Multilayer Crimp Fitting 51018 ∙ 25mm Brass Coupler Multilayer Crimp Fitting 51022 ∙ 32mm Brass Coupler Multilayer Crimp Fitting Unequal Straight Union (20mmx16mm - 32mmx26mm): 51028 ∙ 20x16mm Reducing Coupler Multilayer Crimp Fitting 51040 ∙ 25x16mm Reducing Coupler Multilayer Crimp Fitting 51038 ∙ 25x20mm Reducing Coupler Multilayer Crimp Fitting 51031 ∙ 32x16mm Reducing Coupler Multilayer Crimp Fitting 51032 ∙ 32x20mm Reducing Coupler Multilayer Crimp Fitting 51039 ∙ 32x25mm Reducing Coupler Multilayer Crimp Fitting Male Straight Union (16mmx⅜” BSP (M) - 32mmx1” BSP (M)): 51081 ∙ 16mm x 1/2" Male Iron Multilayer Crimp Coupler 51083 ∙ 20mm x 1/2" Male Iron Multilayer Crimp Coupler 51084 ∙ 20mm x 3/4" Male Iron Multilayer Crimp Coupler 51082 ∙ 25mm x 3/4" Male Iron Multilayer Crimp Fitting 51085 ∙ 25mm x 1" Male Iron Multilayer Crimp Fitting 51088 ∙ 32mm x 1" Male Iron Multilayer Crimp Coupler Female Straight Union (16mmx⅜” BSP (F) - 32mmx1” BSP (F)): 51067 ∙ 16mm x 1/2" Female Iron Multilayer Crimp Coupler 51069 ∙ 20mm x 1/2" Female Iron Multilayer Crimp Coupler 51070 ∙ 20mm x 3/4" Female Iron Multilayer Crimp Coupler 51095 ∙ 25mm x 3/4" Female Iron Multilayer Crimp Fitting 51068 ∙ 25mm x 1" Female Iron Multilayer Crimp Fitting 51073 ∙ 32mm x 1" Female Iron Multilayer Crimp Coupler Equal Elbows (16mm - 32mm): 51044 ∙ 16mm Brass 90 Elbow Multilayer Crimp Fitting 51045 ∙ 20mm Brass 90 Elbow Multilayer Crimp Fitting 51043 ∙ 25mm Brass 90 Elbow Multilayer Crimp Fitting 51047 ∙ 32mm Brass 90 Elbow Multilayer Crimp Fitting Male Elbows (16mmx⅜” BSP (M) - 32mmx1” BSP (M)): 51096 ∙ 16mm x 1/2" Male Iron Elbow Multilayer Crimp Fitting 51098 ∙ 20mm x 3/4" Male Iron Elbow Multilayer Crimp Fitting 51099 ∙ 25mm x 1" Male Iron Elbow Multilayer Crimp Fitting Female Elbows (16mmx⅜ BSP (F) - 32mmx1” BSP (F)): 51096 ∙ 16mm x 1/2" Female Iron Elbow Multilayer Crimp Fitting 51108 ∙ 16mm x 1/2" Female Iron Elbow Multilayer Crimp Fitting 51109 ∙ 20mm x 3/4" Female Iron Elbow Multilayer Crimp Fitting 51105 ∙ 25mm x 3/4" Female Iron Elbow Multilayer Crimp Fitting 51106 ∙ 25mm x 1" Female Iron Elbow Multilayer Crimp Fitting Equal Tees (16mm - 32mm): 51058 ∙ 16mm Brass Equal Tee Multilayer Crimp Fitting 51059 ∙ 20mm Brass Equal Tee Multilayer Crimp Fitting 51042 ∙ 25mm Brass Equal Tee Multilayer Crimp Fitting 51061 ∙ 32mm Brass Equal Tee Multilayer Crimp Fitting Unequal Tees (16mmx20mmx16mm - 32mmx26mmx32mm): 51140 ∙ 16x16x20mm Reducing Ends Tee Multilayer Crimp 51142 ∙ 20x16x16mm Reducing End & Branch Tee Multilayer Crimp 51121 ∙ 20x20x16mm Reducing Branch Tee Multilayer Crimp 51137 ∙ 20x20x25mm Reducing Ends Tee Multilayer Crimp 51124 ∙ 25x25x16mm Reducing Branch Tee Multilayer Crimp 51147 ∙ 25x20x20mm Reducing End & Branch Tee Multilayer Crimp 51125 ∙ 25x25x20mm Reducing Branch TEE Multilayer Crimp 51129 ∙ 32x32x20mm Reducing Branch Tee Multilayer Crimp 51130 ∙ 32x32x25mm Reducing Branch Tee Multilayer Crimp Female Tee (16mmx16mmx⅜” BSP (F) - 32mmx32mmx1” BSP (F)): 51155 ∙ 16mm x 1/2" Female Iron Branch Tee Multilayer Crimp 51156 ∙ 20mm x 1/2" Female Iron Branch Tee Multilayer Crimp 51157 ∙ 25mm x 3/4" Female Iron Branch Tee Multilayer Crimp Wall-plated female elbow (16mmx⅜” BSP (F) - 26mmx¾” BSP (F)): 51171 ∙ 16mm x 1/2" Backplate Elbow Multilayer Crimp 51173 ∙ 20mm x 3/4" Backplate Elbow Multilayer Crimp. _________

Approval Holder:

Brymec Ltd

Company Name

Brymec Ltd

Address

Redlands , Coulsdon, Surrey

Postcode

CR5 2HT

Country

United Kingdom

General Email

Jeremy.douglas@brymec.com

View All Listings by this Company

Range of plastic and DZR brass pushfit fittings for use with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) and copper pipes (manufactured to EN 1057). Maximum working pressure 10.0 bar, except tank connectors which are open outlet use only. Cold water use only. From March 2026: Maximum operating temperature 65°C for all models except tank connectors.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251015003

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

R008 applies to the ATC tank connectors.

Size:

See model.

Marking:

Twistloc company logo (‘TLC’) and size either on body and/or collet.

Installation Requirements:

R001 R008

Expiry date:

31/10/2030

Model:

Plastic Fittings: SMF6741M-2P - 2 Ports Manifold 22mm pushfit x 10mm pushfit x 10mm pushfit. SMF6746M-2P - 2 Ports Manifold 22mm pushfit x 15mm pushfit x 15mm pushfit. SMF6741M-4P - 4 Ports Manifold 22mm pushfit x 10mm pushfit x 10mm pushfit x 10mm pushfit. ATC44M - Tank connector 22mm pushfit x ¾" BSP (M). ATC66M - Tank connector 15mm pushfit x ½” BSP (M). ATC00M - Tank connector 28mm pushfit x 1” BSP (M). ATC44MBK - Tank connector 22mm pushfit x ¾" BSP (M). ATC66MBK - Tank connector 15mm pushfit x ½” BSP (M). ATC00MBK - Tank connector 28mm pushfit x 1” BSP (M). DZR Brass Fittings: SBFCA6741M - Cylinder Adaptor 22mm pushfit x 1" BSP (F). SBFA6764M - Female Coupler 15mm pushfit x ½" BSP (F). SBFA6765M - Female Coupler 15mm pushfit x ¾" BSP (F). SBFA6745M - Female Coupler 22mm pushfit x ¾" BSP (F). SBMCC6741M - Cylinder Adaptor 22mm pushfit x 1" BSP (M). SBMC6714M - Male Coupler 10mm pushfit x ½" BSP (M). SBMC6764M - Male Coupler 15mm pushfit x ½" BSP (M). SBMC6745M - Male Coupler 22mm pushfit x ¾" BSP (M). SBBPE6764M - Back Plate Elbow 15mm pushfit x ½" BSP (F). SBMSA6764M - Male Stem Adaptor 15mm x ½" BSP (M). SBMSA6745M - Male Stem Adaptor 22mm x ¾" BSP (M). SBMSA6701M - Male Stem Adaptor 28mm x 1" BSP (M). SBFSA6764M - Female Stem Adaptor 15mm x ½" BSP (F). SBFSA6745M - Female Stem Adaptor 22mm x ¾” BSP (F).

Approval Holder:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

General Email

nchoi@twistloc.com

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

General Email

nchoi@twistloc.com

View All Listings by this Company

'Flomasta' range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe (EN1057). Maximum working pressure/temperature: 12.5 Bar @ 20°C. As of October 2025: Maximum working pressure/temperature 3 Bar @ 92°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250602054

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

10mm, 15mm, 22mm, 28mm

Marking:

TLC (TwistLoc logo) and size on body

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

‘Flomasta’ range comprising of models: SRDE6764M 15mmX1/2"BSP DROP EAR ELBOW SRF6764M 15mmX1/2"BSP FEMALE ADAPTOR SRF6765M 15mmX3/4"BSP FEMALE ADAPTOR SRF6745M 22mmX3/4"BSP FEMALE ADAPTOR SRF6701M 28mmX1"BSP FEMALE ADAPTOR SPU6711M 10mm STR UNION SPU6766M 15mm STR UNION SPU6744M 22mm STR UNION SPU6700M 28mm STR UNION SPU6761M 15mmX10mm REDUCING STR UNION SPU6746M 22mmX15mm REDUCING STR UNION SRSE6714M 10mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6764M 15mmX1/2"BSP SWIVEL ELBOW (Hand Tighten) SRSE6765M 15mmX3/4"BSP SWIVEL ELBOW (Hand Tighten) SRSE6714BM 10mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6764BM 15mmX1/2"BSP SWIVEL ELBOW (Brass Nut) SRSE6765BM 15mmX3/4"BSP SWIVEL ELBOW (Brass Nut) SPSU6714M 10mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6764M 15mmX1/2"BSP SWIVEL UNION (Hand Tighten) SRSU6765M 15mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6745M 22mmX3/4"BSP SWIVEL UNION (Hand Tighten) SPSU6714BM 10mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6764BM 15mmX1/2"BSP SWIVEL UNION (Brass Nut) SRSU6765BM 15mmX3/4"BSP SWIVEL UNION (Brass Nut) SPSU6745BM 22mmX3/4"BSP SWIVEL UNION (Brass Nut) SPST671M 10mm END STOP SPST676M 15mm END STOP SPST674M 22mm END STOP SRST670M 28mm END STOP SPE6711M 10mm ELBOW SPE6766M 15mm ELBOW SPE6744M 22mm ELBOW SPE6700M 28mm ELBOW SPE6761M 15mmX10mm REDUCING ELBOW SPE6746M 22mmX15mm REDUCING ELBOW SPATE6766M 15mm-135o STEM ELBOW SPATE6744M 22mm-135o STEM ELBOW SPR6716M 10mmX15mm REDUCER SPR6764M 15mmX22mm REDUCER SPR6760M 15mmX28mm REDUCER SPR6740M 22mmX28mm REDUCER SPT67111M 10mm TEE SPT67666M 15mm TEE SPT67444M 22mm TEE SPT67000M 28mm TEE SPT67611M 15mmX10mmX10mm REDUCING TEE SPT67661M 15mmX15mmX10mm REDUCING TEE SPT67664M 15mmX15mmX22mm REDUCING TEE SPT67466M 22mmX15mmX15mm REDUCING TEE SPT67464M 22mmx15mmx22mm REDUCING TEE SPT67441M 22mmx22mmx10mm REDUCING TEE SPT67446M 22mmX22mmX15mm REDUCING TEE SPT67044M 28mmX22mmX22mm REDUCING TEE SPT67040M 28mmX22mmX28mm REDUCING TEE SPT67001M 28mmX28mmX10mm REDUCING TEE SPT67006M 28mmX28mmX15mm REDUCING TEE SPT67004M 28mmX28mmX22mm REDUCING TEE SPTT67441M 22mX22mmX10mm TUBE TEE SPTT67446M 22mX22mmX15mm TUBE TEE SPTE6711M 10mm TUBE ELBOW SPTE6716M 10mmx15mm TUBE ELBOW SPTE6766M 15mm TUBE ELBOW SPTE6744M 22mm TUBE ELBOW SRMC6764M 15mmX1/2"BSPT MALE CONNECTOR SRME6764M 15mmX1/2"BSPT MALE ELBOW SRFWC6741M 22mmX10mm 4WAY MANIFOLD SRU6766SM 15mm SLIP UNION SRU6744SM 22mm SLIP UNION STS10M 10mm PIPE INSERT STS15M 15mm PIPE INSERT STS22M 22mm PIPE INSERT STS28M 28mm PIPE INSERT SRAV63M 15mm AIR-VENT CONNECTOR

Approval Holder:

Kingfisher International Products B.V

Company Name

Kingfisher International Products B.V

Address

Rapenburgerstraat 175E, 1011 VM Amsterdam

Country

Netherlands

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

View All Listings by this Company

Manufacturer:

SNC Corporation

Company Name

SNC Corporation

Address

30, Baekbeom-ro, 678 beon-gil, Seo-gu, Incheon

Postcode

22825

Country

South Korea

Phone

+82-70-8795-3200

View All Listings by this Company

Range of polypropylene push-fit fittings. The 20, 25 and 32mm sizes are for use with MDPE Pipe (manufactured to BS EN 12201-2). The 15, 22 and 28mm connections are for use with the following pipes: PEX (manufactured to BS 7291-3) for 15, 22 and 28mm sizes. PB (manufactured to BS 7291-2) and Copper (manufactured to BS EN 1057) for 15 and 22mm sizes only. Maximum working pressures: UG601B model: 16.0 bar. All other models: 12.5 bar. Cold water use only.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

260202004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The blue (UTS) and beige (TSM) pipe inserts must be used to maintain the validity of this approval.

Size:

See model.

Marking:

PN, JG & size on body. JG on pipe inserts.

Installation Requirements:

R001

Expiry date:

28/02/2031

Model:

Couplers: UG601B: 20 x 15MM PE-COPPER COUPLER, UG602B: 25 x 22Mm PE-COPPER COUPLER, UG603B: 25 x 15MM PE-COPPER COUPLER, UG604B: 32 x 28MM PE-COPPER COUPLER, UG063228B: 32 x 28MM REDUCER. Pipe inserts (blue) for use with MDPE pipe: UTS147-DB 20MM pipe insert, UTS197-DB 25MM pipe insert, UTS251-DB 32MM pipe insert. Pipe inserts (beige) for use with PB or PEX pipe: TSM15N 15MM pipe insert, TSM22N 22MM pipe insert. Pipe inserts (beige) for use with PEX pipe: TSM28N 28MM pipe insert.

Approval Holder:

Reliance Worldwide Corporation (UK)

Company Name

Reliance Worldwide Corporation (UK)

Address

Horton Road, West Drayton

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

General Email

PETER.LANCASTER@RWC.COM

View All Listings by this Company

Range of end feed copper fittings for use with copper pipes (manufactured to EN 1057). The 5043G series and 5002G series models incorporate an EPDM ‘O’-ring on the captive nut connection. For above and below ground use. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251015004

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Linhai Hengye Tubing Equipment Co., Ltd logo (‘IoJ’) and size on body.

Installation Requirements:

R001

Expiry date:

31/10/2030

Model:

5270 series - Coupling: 52706: 6mm, 52708: 8mm, 527010: 10mm, 527012: 12mm, 527014: 14mm, 527015: 15mm, 527016: 16mm, 527018: 18mm, 527022: 22mm, 527028: 28mm, 527035: 35mm, 527040: 40mm, 527042: 42mm, 527054: 54mm, 527064: 64mm, 527067: 67mm, 527070: 70mm, 527076: 76mm, 527089: 89mm, 5270108: 108mm. 5270S series - Slip coupling: 5270S12: 12mm, 5270S15: 15mm, 5270S18: 18mm, 5270S22: 22mm, 5270S28: 28mm, 5270S35: 35mm, 5270S42: 42mm, 5270S54: 54mm, 5270S67: 67mm, 5270S76: 76mm, 5270S108: 108mm. 5240MI series - Coupling for BS and Irish: 5240MI1512: 15mmx1/2", 5240MI2234: 22mmx3/4", 5240MI281: 28mmx1", 5240MI35114: 35mmx1-1/4". 5240 series - Reducing coupling: 524086: 8x6mm, 5240106: 10x6mm, 5240108: 10x8mm, 5240126: 12x6mm, 5240128: 12x8mm, 52401210: 12x10mm, 52401410: 14x10mm, 52401412: 14x12mm, 5240158: 15x8mm, 52401510: 15x10mm, 52401512: 15x12mm, 52401514: 15x14mm, 52401610: 16x10mm, 52401612: 16x12mm, 52401614: 16x14mm, 52401615: 16x15mm, 52401810: 18x10mm, 52401812: 18x12mm, 52401814: 18x14mm, 52401815: 18x15mm, 52401816: 18x16mm, 52402210: 22x10mm, 52402212: 22x12mm, 52402214: 22x14mm, 52402215: 22x15mm, 52402216: 22x16mm, 52402218: 22x18mm, 52402812: 28x12mm, 52402814: 28x14mm, 52402815: 28x15mm, 52402816: 28x16mm, 52402818: 28x18mm, 52402822: 28x22mm, 52403515: 35x15mm, 52403518: 35x18mm, 52403522: 35x22mm, 52403528: 35x28mm, 52404028: 40x28mm, 52404215: 42x15mm, 52404222: 42x22mm, 52404228: 42x28mm, 52404235: 42x35mm, 52405415: 54x15mm, 52405422: 54x22mm, 52405428: 54x28mm, 52405435: 54x35mm, 52405442: 54x42mm, 52406435: 64x35mm, 52406442: 64x42mm, 52406454: 64x54mm, 52406735: 67x35mm, 52406742: 67x42mm, 52406754: 67x54mm, 52407054: 70x54mm, 52407635: 76x35mm, 52407642: 76x42mm, 52407654: 76x54mm, 52407664: 76x64mm, 52407667: 76x67mm, 52408054: 80x54mm, 52408976: 89x76mm, 524010842: 108x42mm, 524010854: 108x54mm, 524010867: 108x67mm, 524010876: 108x76mm, 524010889: 108x89mm. 5243 series - Fitting reducer: 524386: 8x6mm, 5243106: 10x6mm, 5243108: 10x8mm, 5243126: 12x6mm, 5243128: 12x8mm, 52431210: 12x10mm, 52431410: 14x10mm, 52431412: 14x12mm, 5243158: 15x8mm, 52431510: 15x10mm, 52431512: 15x12mm, 52431514: 15x14mm, 52431610: 16x10mm, 52431612: 16x12mm, 52431614: 16x14mm, 52431615: 16x15mm, 52431810: 18x10mm, 52431812: 18x12mm, 52431814: 18x14mm, 52431815: 18x15mm, 52431816: 18x16mm, 52432210: 22x10mm, 52432212: 22x12mm, 52432214: 22x14mm, 52432215: 22x15mm, 52432216: 22x16mm, 52432218: 22x18mm, 52432810: 28x10mm, 52432812: 28x12mm, 52432814: 28x14mm, 52432815: 28x15mm, 52432816: 28x16mm, 52432818: 28x18mm, 52432822: 28x22mm, 52433515: 35x15mm, 52433518: 35x18mm, 52433522: 35x22mm, 52433528: 35x28mm, 52434028: 40x28mm, 52434215: 42x15mm, 52434218: 42x18mm, 52434222: 42x22mm, 52434228: 42x28mm, 52434235: 42x35mm, 52435415: 54x15mm, 52435422: 54x22mm, 52435428: 54x28mm, 52435435: 54x35mm, 52435442: 54x42mm, 52436435: 64x35mm, 52436442: 64x42mm, 52436454: 64x54mm, 52436722: 67x22mm, 52436728: 67x28mm, 52436735: 67x35mm, 52436742: 67x42mm, 52436754: 67x54mm, 52437042: 70x42mm, 52437635: 76x35mm, 52437642: 76x42mm, 52437654: 76x54mm, 52437664: 76x64mm, 52437667: 76x67mm, 52438054: 80x54mm, 52438064: 80x64mm, 52438954: 89x54mm, 52438964: 89x64mm, 52438976: 89x76mm, 524310835: 108x35mm, 524310842: 108x42mm, 524310854: 108x54mm, 524310867: 108x67mm, 524310876: 108x76mm, 524310889: 108x89mm. 5090 series - Elbow: 50906: 6mm, 50908: 8mm, 509010: 10mm, 509012: 12mm, 509014: 14mm, 509015: 15mm, 509016: 16mm, 509018: 18mm, 509022: 22mm, 509025: 25mm, 509028: 28mm, 509035: 35mm, 509040: 40mm, 509042: 42mm, 509054: 54mm, 509064: 64mm, 509067: 67mm, 509076: 76mm, 509089: 89mm, 5090108: 108mm. 5092 series - Street elbow 90°: 50926: 6mm, 50928: 8mm, 509210: 10mm, 509212: 12mm, 509214: 14mm, 509215: 15mm, 509216: 16mm, 509218: 18mm, 509222: 22mm, 509228: 28mm, 509235: 35mm, 509240: 40mm, 509242: 42mm, 509254: 54mm, 509264: 64mm, 509267: 67mm. 5090 series - Reducing elbow 90°: 50901512: 15x12mm, 50902215: 22x15mm, 50902822: 28x22mm, 50903528: 35x28mm. 5041 series - Elbow 45°: 50416: 6mm, 50418: 8mm, 504110: 10mm, 504112: 12mm, 504114: 14mm, 504115: 15mm, 504116: 16mm, 504118: 18mm, 504122: 22mm, 504128: 28mm, 504135: 35mm, 504140: 40mm, 504142: 42mm, 504154: 54mm, 504164: 64mm, 504167: 67mm, 504170: 70mm, 504176: 76mm, 504180: 80mm, 504189: 89mm, 5041108: 108mm. 5040 series - Street elbow 45°: 50406: 6mm, 50408: 8mm, 504010: 10mm, 504012: 12mm, 504014: 14mm, 504015: 15mm, 504016: 16mm, 504018: 18mm, 504022: 22mm, 504028: 28mm, 504035: 35mm, 504040: 40mm, 504042: 42mm, 504054: 54mm, 504064: 64mm, 504067: 67mm, 504076: 76mm, 504089: 89mm, 5040108: 108mm. 5002A series - Bend 90°: 5002A6: 6mm, 5002A8: 8mm, 5002A10: 10mm, 5002A12: 12mm, 5002A14: 14mm, 5002A15: 15mm, 5002A16: 16mm, 5002A18: 18mm, 5002A22: 22mm, 5002A28: 28mm, 5002A35: 35mm, 5002A40: 40mm, 5002A42: 42mm, 5002A54: 54mm, 5002A64: 64mm, 5002A67: 67mm, 5002A70: 70mm, 5002A76: 76mm, 5002A80: 80mm, 5002A89: 89mm, 5002A108: 108mm. 5001A series - Street bend 90°: 5001A6: 6mm, 5001A8: 8mm, 5001A10: 10mm, 5001A12: 12mm, 5001A14: 14mm, 5001A15: 15mm, 5001A16: 16mm, 5001A18: 18mm, 5001A22: 22mm, 5001A28: 28mm, 5001A35: 35mm, 5001A40: 40mm, 5001A42: 42mm, 5001A54: 54mm, 5001A64: 64mm, 5001A67: 67mm, 5001A76: 76mm, 5001A80: 80mm, 5001A89: 89mm, 5001A108: 108mm, 5085 series - Full crossover: 508512: 12mm, 508514: 14mm, 508515: 15mm, 508516: 16mm, 508518: 18mm, 508522: 22mm, 508528: 28mm. 5086 series - Part crossover: 508612: 12mm, 508614: 14mm, 508615: 15mm, 508616: 16mm, 508618: 18mm, 508622: 22mm, 508628: 28mm. 5130 series - Equal tee: 51306: 6mm, 51308: 8mm, 513010: 10mm, 513012: 12mm, 513014: 14mm, 513015: 15mm, 513016: 16mm, 513018: 18mm, 513022: 22mm, 513028: 28mm, 513035: 35mm, 513040: 40mm, 513042: 42mm, 513054: 54mm, 513064: 64mm, 513067: 67mm, 513070: 70mm, 513076: 76mm, 513080: 80mm, 513089: 89mm, 5130108: 108mm. 5130 series - Reducing tee: 5130686: 6x8x6mm, 51306106: 6x10x6mm, 5130866: 8x6x6mm, 5130868: 8x6x8mm, 51308108: 8x10x8mm, 51301088: 10x8x8mm, 513010610: 10x6x10mm, 513010810: 10x8x10mm, 5130101210: 10x12x10mm, 5130101510: 10x15x10mm, 513010108: 10x10x8mm, 513012612: 12x6x12mm, 513012812: 12x8x12mm, 513012810: 12x8x10mm, 5130121010: 12x10x10mm, 5130121210: 12x12x10mm, 5130121012: 12x10x12mm, 5130121412: 12x14x12mm, 5130121512: 12x15x12mm, 5130121612: 12x16x12mm, 5130121812: 12x18x12mm, 5130141212: 14x12x12mm, 5130141412: 14x14x12mm, 5130141812: 14x18x12mm, 5130141014: 14x10x14mm, 5130141214: 14x12x14mm, 5130141614: 14x16x14mm, 5130141814: 14x18x14mm, 5130142214: 14x22x14mm, 5130151010: 15x10x10mm, 5130151012: 15x10x12mm, 5130151510: 15x15x10mm, 5130151212: 15x12x12mm, 5130151512: 15x15x12mm, 5130151812: 15x18x12mm, 513015615: 15x6x15mm, 513015815: 15x8x15mm, 5130151015: 15x10x15mm, 5130151215: 15x12x15mm, 5130151815: 15x18x15mm, 5130152215: 15x22x15mm, 5130161610: 16x16x10mm, 5130161212: 16x12x12mm, 5130161412: 16x14x12mm, 5130161612: 16x16x12mm, 5130161214: 16x12x14mm, 5130161414: 16x14x14mm, 5130161614: 16x16x14mm, 5130161814: 16x18x14mm, 513016616: 16x6x16mm, 513016816: 16x8x16mm, 5130161016: 16x10x16mm, 5130161216: 16x12x16mm, 5130161416: 16x14x16mm, 5130161816: 16x18x16mm, 5130162216: 16x22x16mm, 5130181212: 18x12x12mm, 5130181512: 18x15x12mm, 5130181812: 18x18x12mm, 5130181414: 18x14x14mm, 5130181614: 18x16x14mm, 5130181814: 18x18x14mm, 5130181215: 18x12x15mm, 5130181515: 18x15x15mm, 5130181815: 18x18x15mm, 5130182215: 18x22x15mm, 5130181416: 18x14x16mm, 5130181616: 18x16x16mm, 5130181816: 18x18x16mm, 513018618: 18x6x18mm, 5130181018: 18x10x18mm, 5130181218: 18x12x18mm, 5130181418: 18x14x18mm, 5130181518: 18x15x18mm, 5130181618: 18x16x18mm, 5130182218: 18x22x18mm, 5130182818: 18x28x18mm, 5130221212: 22x12x12mm, 5130221414: 22x14x14mm, 5130221614: 22x16x14mm, 5130221814: 22x18x14mm, 5130222214: 22x22x14mm, 5130221215: 22x12x15mm, 5130221515: 22x15x15mm, 5130221815: 22x18x15mm, 5130222212: 22x22x12mm, 5130222215: 22x22x15mm, 5130221616: 22x16x16mm, 5130221816: 22x18x16mm, 5130222216: 22x22x16mm, 5130221218: 22x12x18mm, 5130221418: 22x14x18mm, 5130221518: 22x15x18mm, 5130221618: 22x16x18mm, 5130221818: 22x18x18mm, 5130222218: 22x22x18mm, 513022622: 22x6x22mm, 5130221022: 22x10x22mm, 5130221222: 22x12x22mm, 5130221422: 22x14x22mm, 5130221522: 22x15x22mm, 5130221622: 22x16x22mm, 5130221822: 22x18x22mm, 5130222822: 22x28x22mm, 5130281515: 28x15x15mm, 5130281815: 28x18x15mm, 5130282215: 28x22x15mm, 5130282815: 28x28x15mm, 5130282816: 28x28x16mm, 5130281518: 28x15x18mm, 5130281818: 28x18x18mm, 5130282216: 28x22x16mm, 5130282218: 28x22x18mm, 5130282818: 28x28x18mm, 5130281522: 28x15x22mm, 5130281622: 28x16x22mm, 5130281822: 28x18x22mm, 5130282222: 28x22x22mm, 5130282822: 28x28x22mm, 5130281028: 28x10x28mm, 5130281228: 28x12x28mm, 5130281428: 28x14x28mm, 5130281528: 28x15x28mm, 5130281628: 28x16x28mm, 5130281828: 28x18x28mm, 5130282228: 28x22x28mm, 5130283528: 28x35x28mm, 5130353515: 35x35x15mm, 5130352818: 35x28x18mm, 5130353518: 35x35x18mm, 5130352222: 35x22x22mm, 5130352822: 35x28x22mm, 5130353522: 35x35x22mm, 5130351528: 35x15x28mm, 5130351828: 35x18x28mm, 5130352228: 35x22x28mm, 5130352828: 35x28x28mm, 5130353528: 35x35x28mm, 5130351535: 35x15x35mm, 5130351835: 35x18x35mm, 5130352235: 35x22x35mm, 5130352835: 35x28x35mm, 5130354235: 35x42x35mm, 5130422828: 42x28x28mm, 5130421542: 42x15x42mm, 5130421842: 42x18x42mm, 5130422242: 42x22x42mm, 5130422842: 42x28x42mm, 5130423542: 42x35x42mm, 5130425442: 42x54x42mm, 5130424222: 42x42x22mm, 5130424228: 42x42x28mm, 5130422235: 42x22x35mm, 5130422835: 42x28x35mm, 5130423535: 42x35x35mm, 5130424235: 42x42x35mm, 5130541554: 54x15x54mm, 5130541854: 54x18x54mm, 5130542254: 54x22x54mm, 5130542854: 54x28x54mm, 5130543554: 54x35x54mm, 5130544254: 54x42x54mm, 5130542842: 54x28x42mm, 5130543542: 54x35x42mm, 5130544242: 54x42x42mm, 5130545442: 54x54x42mm, 5130643564: 64x35x64mm, 5130644264: 64x42x64mm, 5130645464: 64x54x64mm, 5130672267: 67x22x67mm, 5130672867: 67x28x67mm, 5130673567: 67x35x67mm, 5130674267: 67x42x67mm, 5130675467: 67x54x67mm, 5130676754: 67x67x54mm, 5130705470: 70x54x70mm, 5130762876: 76x28x76mm, 5130763576: 76x35x76mm, 5130764276: 76x42x76mm, 5130765476: 76x54x76mm, 5130766476: 76x64x76mm, 5130766776: 76x67x76mm, 5130894289: 89x42x89mm, 5130895489: 89x54x89mm, 5130897689: 89x76x89mm, 513010828108: 108x28x108mm, 513010835108: 108x35x108mm, 513010842108: 108x42x108mm, 513010854108: 108x54x108mm, 513010867108: 108x67x108mm, 513010876108: 108x76x108mm, 513010889108: 108x89x108mm. 5243G series - Straight tap connector: 5243G1512: 15mmx1/2"captive nut, 5243G1534: 15mmx3/4"captive nut, 5243G1834: 18mmx3/4"captive nut, 5243G2234: 22mmx3/4"captive nut, 5243G221: 22mmx1"captive nut, 5243G281: 28mmx1"captive nut. 5002G series - Bent tap connector: 5002G1512: 15mmx1/2"captive nut, 5002G1534: 15mmx3/4"captive nut, 5002G1834: 18mmx3/4"captive nut, 5002G2234: 22mmx3/4"captive nut, 5002G221: 22mmx1"captive nut, 5002G281: 28mmx1"captive nut. 5301 series - End cap: 53016: 6mm, 53018: 8mm, 530110: 10mm, 530112: 12mm, 530114: 14mm, 530115: 15mm, 530116: 16mm, 530118: 18mm, 530122: 22mm, 530128: 28mm, 530135: 35mm, 530140: 40mm, 530142: 42mm, 530154: 54mm, 530164: 64mm, 530167: 67mm, 530176: 76mm, 530189: 89mm, 5301108: 108mm. 5060 series - Bend 180°: 50606: 6mm, 50608: 8mm, 506010: 10mm, 506012: 12mm, 506015: 15mm, 506016: 16mm, 506018: 18mm, 506022: 22mm, 506028: 28mm, 506035: 35mm, 506042: 42mm, 506054: 54mm.

Approval Holder:

Linhai Hengye Tubing Equipment Co., Ltd

Company Name

Linhai Hengye Tubing Equipment Co., Ltd

Address

Machinery Industrial Park, Duqiao Town, Linhai City

Country

China

Phone

0086‐576‐85528079

General Email

sales@zjhengye.com

View All Listings by this Company

Range of end feed copper fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.

Section:

1210 Fittings for use with Tube and Pipe

Section Subtitle:

End feed, for use with copper tube. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

251012016

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

Hengsheng logo (HS) and size on body.

Installation Requirements:

R001

Expiry date:

31/10/2030

Model:

5090 (90° Elbow Close Ruff CxC): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5092 (90° Street Elbow Close Ruff Ftg×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5090R (Reducing 90° Elbow C×C): 12mm×10mm, 12mm×8mm, 15mm×12mm, 22mm×15mm, 28mm×22mm, 28mm×15mm, 35mm×28mm, 35mm×22mm, 42mm×35mm, 42mm×28mm, 54mm×42mm, 54mm×35mm, 54mm×28mm. 5041 (45° Elbow C×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5040 (45° Elbow FTG×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5002A (90° Elbow Long Turn C×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5001A (90°Street Elbow Long Turn Ftg×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5130 (Equal Tee C×C×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5130R (Reducing TEE C×C×C): 6mm×6mm×8mm, 8mm×8mm×10mm, 8mm×8mm×6mm, 10mm×10mm×15mm, 10mm×10mm×12mm, 10mm×10mm×8mm, 12mm×12mm×18mm, 12mm×12mm×16mm, 12mm×12mm×15mm, 12mm×12mm×14mm, 12mm×12mm×10mm, 12mm×12mm×8mm, 12mm×12mm×6mm, 14mm×14mm×16mm, 14mm×14mm×12mm, 14mm×14mm×10mm, 15mm×15mm×22mm, 15mm×15mm×12mm, 15mm×15mm×10mm, 15mm×15mm×8mm, 18mm×18mm×22mm, 18mm×18mm×16mm, 18mm×18mm×15mm, 18mm×18mm×14mm, 18mm×18mm×12mm, 18mm×18mm×10mm, 22mm×22mm×28mm, 22mm×22mm×16mm, 22mm×22mm×15mm, 22mm×22mm×12mm, 22mm×22mm×10mm, 28mm×28mm×35mm, 28mm×28mm×22mm, 28mm×28mm×18mm, 28mm×28mm×16mm, 28mm×28mm×15mm, 28mm×28mm×14mm, 28mm×28mm×12mm, 28mm×28mm×10mm, 35mm×35mm×42mm, 35mm×35mm×28mm, 35mm×35mm×22mm, 35mm×35mm×15mm, 42mm×42mm×35mm, 42mm×42mm×28mm, 42mm×42mm×22mm, 42mm×42mm×15mm, 54mm×54mm×42mm, 54mm×54mm×35mm, 54mm×54mm×28mm, 54mm×54mm×22mm, 54mm×54mm×15mm, 8mm×6mm×6mm, 10mm×8mm×10mm, 12mm×10mm×10mm, 12mm×8mm×8mm, 14mm×12mm×12mm, 14mm×12mm×14mm, 15mm×12mm×15mm, 15mm×12mm×12mm, 15mm×12mm×10mm, 15mm×10mm×12mm, 15mm×12mm×8mm, 15mm×10mm×15mm, 15mm×10mm×10mm, 18mm×15mm×15mm, 18mm×15mm×18mm, 18mm×14mm×16mm, 18mm×12mm×18mm, 18mm×12mm×15mm, 18mm×12mm×12mm, 22mm×15mm×22mm, 22mm×15mm×15mm, 22mm×15mm×12mm, 28mm×22mm×28mm, 28mm×22mm×22mm, 28mm×22mm×18mm, 28mm×22mm×15mm, 28mm×18mm×28mm, 28mm×18mm×22mm, 28mm×15mm×28mm, 28mm×15mm×22mm, 28mm×15mm×15mm, 35mm×28mm×35mm, 35mm×28mm×28mm, 35mm×28mm×22mm, 35mm×22mm×35mm, 35mm×22mm×28mm, 35mm×22mm×22mm, 35mm×15mm×35mm, 42mm×35mm×35mm, 42mm×35mm×42mm, 42mm×28mm×42mm, 42mm×22mm×42mm, 54mm×42mm×42mm, 54mm×42mm×54mm, 54mm×35mm×54mm. 5270 (Equal Coupling C×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm. 5240 (Reducing Coupling C×C): 8mm×6mm, 10mm×8mm, 10mm×6mm, 12mm×10mm, 12mm×8mm, 12mm×6mm, 14mm×12mm, 14mm×10mm, 15mm×12mm, 15mm×10mm, 15mm×8mm, 16mm×15mm, 16mm×14mm, 16mm×12mm, 16mm×10mm, 18mm×10mm, 22mm×18mm, 22mm×15mm, 22mm×14mm, 22mm×12mm, 22mm×10mm, 28mm×22mm, 28mm×18mm, 28mm×16mm, 28mm×15mm, 28mm×14mm, 28mm×12mm, 35mm×28mm, 35mm×22mm, 35mm×15mm, 42mm×35mm, 42mm×28mm, 42mm×22mm, 42mm×18mm, 42mm×16mm, 42mm×15mm, 54mm×42mm, 54mm×35mm, 54mm×28mm, 54mm×22mm, 54mm×15mm. 5243 (Fitting Reducer Ftg×C): 8mm×6mm, 10mm×8mm, 10mm×6mm, 12mm×10mm, 12mm×8mm, 12mm×6mm, 14mm×12mm, 14mm×10mm, 15mm×12mm, 15mm×10mm, 15mm×8mm, 16mm×15mm, 16mm×14mm, 16mm×12mm, 16mm×10mm, 18mm×16mm, 18mm×15mm, 18mm×14mm, 18mm×12mm, 18mm×10mm, 22mm×16mm, 22mm×15mm, 22mm×14mm, 22mm×12mm, 22mm×10mm, 28mm×22mm, 28mm×16mm, 28mm×15mm, 28mm×12mm, 35mm×28mm, 35mm×22mm, 35mm×18mm, 35mm×15mm, 42mm×35mm, 42mm×28mm, 42mm×22mm, 42mm×18mm, 42mm×15mm, 54mm×42mm, 54mm×35mm, 54mm×28mm, 54mm×22mm, 54mm×15mm. 5301 (Tube Cap): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm.   5060 (Return Bend C×C): 6mm, 8mm, 10mm, 12mm, 15mm, 22mm, 28mm, 35mm, 42mm, 54mm 5085 (Cross Over Coupling C×C): 15mm, 22mm. 5086 (Partial Cross Over Ftg×C): 15mm, 22mm. 5062 (Straight Tap Connector C×FI): 15mm×1/2", 15mm×3/4", 22mm×3/4", 22mm×1", 28mm×1". 5063 (Bent Tap Connector C×FI): 15mm×1/2", 15mm×3/4", 22mm×3/4", 22mm×1", 28mm×1".

Approval Holder:

Ningbo Hengsheng Pipe Fitting Co.,Ltd.

Company Name

Ningbo Hengsheng Pipe Fitting Co.,Ltd.

Address

No. 28, West Jinshui Road, Ninghai, Ningbo, Zhejiang

Country

China

Phone

0086-574-65338995

General Email

sales@hengshen.com

View All Listings by this Company

Range of ultrasonic dry type water meters with brass bodies. Maximum working pressure 16.0 Bar. Maximum operating temperature 50.0°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models

Marking:

BAYLAN, model number and other technical information on meter face. Flow arrow on body

Installation Requirements:

R001

Expiry date:

31/10/2030

Model:

ST-15. DN15 - thread size ¾” BSP (M). Lengths - 110mm, 115mm, 130mm, 145mm, 165mm, 170mm, 190mm. ST-20. DN20 - thread size 1” BSP (M). Lengths - 110mm, 115mm, 130mm, 135mm, 165mm, 175mm, 190mm, 200mm, 220mm. ST-25. DN25 - thread size 1 ¼” BSP (M). Lengths - 175mm, 199mm, 200mm, 210mm, 225mm. ST-32. DN32 - thread size 1 ½” BSP (M). Lengths - 110mm, 150mm, 175mm, 199mm, 200mm ST-40. DN40 - thread size 2” BSP (M). Lengths - 200mm, 220mm.

Approval Holder:

BAYLAN OLCU ALETLERI SAN. TICARET

Company Name

BAYLAN OLCU ALETLERI SAN. TICARET

Address

ANONIM SIRKETI AOSB 10032 SOKAK NO 16 CIGLI IZMIR TURKEY

View All Listings by this Company

Manufacturer:

BAYLAN OLCU ALETLERI SAN. TICARET

Company Name

BAYLAN OLCU ALETLERI SAN. TICARET

Address

ANONIM SIRKETI AOSB 10032 SOKAK NO 16 CIGLI IZMIR TURKEY

View All Listings by this Company

Range of water meters with brass bodies. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature is 50°C or 85°C, please refer to model.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (M) or 1” BSP (M)

Marking:

Resideo and product information on face of water meter. Resideo, POWOGAZ & technical info label on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

Maximum operating temperature 50°C: EW1100AC060 EW1100AC2000 EW1050AP2000 EW1100AC1100 EW1100AC1200 EW1100CM1200 EW1050AP1200 EW1100CM2000 Maximum operating temperature 85°C: EW1101AC0600 EW1101AC1100 EW1101AC1200 EW1101AC1400 EW1051AP1200 EW1100AC1400 EW1101CM1200 EW1101AC2000 EW1101CM2000 EW1051AP2000

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Manufacturer:

Apator Powogaz S.A.

Company Name

Apator Powogaz S.A.

Address

Jaryszki 1C, 62-023 Żerniki

Country

Poland

Phone

+48 789 454 593

View All Listings by this Company

Manufacturer:

Apator Powogaz S.A.

Company Name

Apator Powogaz S.A.

Address

Jaryszki 1C, 62-023 Żerniki

Country

Poland

Phone

+48 789 454 593

View All Listings by this Company

Range of brass bodied threaded fittings and a brass end feed fitting (C04069H00081A model only). The CL08069H192B4 model is chrome plated. The C04069H00081A model end feed fitting is for use with copper pipe (manufactured to EN 1057). The C04149H00191A model incorporates a plastic flow straightener. Maximum working pressure 10.0 bar, except for the C04149H00190A and C04149H00191A models which are open outlet use only. Maximum operating temperature 85°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model.

Marking:

AVONFLOW and WRAS on body.

Installation Requirements:

R001

Expiry date:

31/10/2030

Model:

C04149H00190A - 3/4 Brass Hose Union Nut & Tail: 7/8” BSP (F) inlet x 19.5mm barbed outlet, C04149H00191A - 1/2 Brass Hose Union Nut & Tail: 3/4” BSP (F) x 15.6mm barbed outlet, CL08069H185W2 - Brass Flange Plug 1/4 Bp14: 1/4" BSP (M), CL08069H186W2 - Brass Flanged Plug 3/8 Bp38: 3/8” BSP (M), CL08069H187W2 - Brass Flanged Plug 1/2 Bp12: 1/2" BSP (M), CL08069H188W2 - BRASS FLANGED PLUG 3/4" BP34: 3/4” BSP (M), CL08069H189W2 - Brass Flanged Plug 1 Bp1: 1” BSP (M), CL08069H190W2 - Brass Flange Plug 11/2 Bp112: 1-1/2" BSP (M), CL08069H183W2 - Brass Flanged Plug 1 1/4 Bp114: 1-1/4" BSP (M), CL41039H247W2 - Brass Hexagon Bush 1/4 X 1/8 Bb1418: 1/4” BSP (M) x 1/8” BSP (F), CL41039H228W2 - Brass Hexagon Bush 3/8 X 1/4 Bb3814: 3/8” BSP (M) x 1/4” BSP (F), CL41039H229W2 - Brass Hex Bush 1/2 X 1/8 Bb1218: 1/2” BSP (M) x 1/8” BSP (F), CL41039H230W2 - Brass Hexagon Bush 1/2 X 1/4 Bb1214: 1/2” BSP (M) x 1/4” BSP (F), CL41039H231W2 - Brass Hexagon Bush 1/2 X 3/8 Bb1238: 1/2” BSP (M) x 3/8” BSP (F), CL41039H232W2 - Brass Hexagon Bush 3/4 X 1/2 Bb3412: 3/4” BSP (M) x 1/2” BSP (F), CL41039H233W2 - Brass Hex Bush 1 X 1/2 Bb112: 1” BSP (M) x 1/2” BSP (F), CL41039H234W2 - Brass Hexagon Bush 1 X 3/4 Bb134: 1” BSP (M) x 3/4” BSP (F), CL41039H235W2 - Brass Hexagon Bush 1 1/4 X 1/2 Bb11412: 1-1/4” BSP (M) x 1/2” BSP (F), CL41039H236W2 - Brass Hexagon Bush 1 1/4 X 3/4 Bb11434: 1-1/4” BSP (M) x 3/4” BSP (F), CL41039H239W2 - Brass Hexagon Bush 1 1/4 X 1 Bb1141: 1-1/4” BSP (M) x 1” BSP (F), CL41039H240W2 - Brass Hexagon Bush 1 1/2 X 1/2 Bb11212: 1-1/2” BSP (M) x 1/2” BSP (F), CL41039H241W2 - Brass Hexagon Bush 1 1/2 X 1 Bb1121: 1-1/2” BSP (M) x 1” BSP (F), CL41039H242W2 - Brass Hex Bush 1 1/2 X 1 1/4 Bb112114: 1-1/2” BSP (M) x 1-1/4” BSP (F), CL41039H243W2 - Brass Hexagon Bush 2 X 1 Bb21: 2” BSP (M) x 1” BSP (F), CL41039H244W2 - Brass Hexagon Bush 2 X 1 1/4 Bb2114: 2” BSP (M) x 1-1/4” BSP (F), CL41039H245W2 - Brass Hexagon Bush 2 X 1 1/2 Bb2112: 2” BSP (M) x 1-1/2” BSP (F), CL08019H381W2 - Brass Socket 1/2 Bs12: 1/2” BSP (F), CL08019H382W2 - Brass Socket 3/4 Bs34: 3/4” BSP (F), CL08019H383W2 - Brass Socket 1 Bs1: 1” BSP (F), CL08019H384W2 - PLUMBRIGHT BRASS HEXAGON NIPPLE 1/4": 1/4” BSP (M), CL08019H385W2 - Brass Hexagon Nipple 1/2 Bn12: 1/2” BSP (M), CL08019H386W2 - Brass Hexagon Nipple 3/4 Bn34: 3/4” BSP (M), CL08019H387W2 - Brass Hexagon Nipple 1 Bn1: 1” BSP (M), CL41039H237W2 - Brass Hexagon Nipple 3/8 Bn38: 3/8” BSP (M), CL41039H238W2 - Brass Tap Extension Mxf 1/2 Be12: 1/2” BSP (F) x 1/2” BSP (M), CL08019H389A2 - PLUMBRIGHT BRASS BARREL NIPPLE 3/8": 3/8” BSP (M), CL08019H390A2 - PLUMBRIGHT BRASS BARREL NIPPLE 1/2": 1/2” BSP (M), CL08019H391A2 - PLUMBRIGHT BRASS BARREL NIPPLE 3/4": 3/4” BSP (M), CL08019H392A2 - PLUMBRIGHT BRASS BARREL NIPPLE 1": 1” BSP (M), CL08069H192B4 - Brass Cap-Cp 1/2 Cpbc12: 1/2” BSP (F), CL08069H193W2 - Brass Cap 1/4 Bc14: 1/4” BSP (F), CL08069H194W2 - Brass Cap 3/8 Bc38: 3/8” BSP (F), CL08069H192W2 - Brass Cap 1/2 Bc12: 1/2” BSP (F), CL08069H195W2 - Brass Cap 3/4 Bc34: 3/4” BSP (F), CL08069H196W2 - Brass Cap 1 Bc1: 1” BSP (F), C04069H00081A - P/R END FEED AIR RELEASE STOP END 15MM: 15mm.

Approval Holder:

Jiangxi Avonflow Hvac Tech Co., Ltd

Company Name

Jiangxi Avonflow Hvac Tech Co., Ltd

Address

No.97, Xingye Avenue, Economic Development Zone, Shangrao City Jiangxi Province

Country

China

View All Listings by this Company

Manufacturer:

Jiangxi Avonflow Hvac Tech Co., Ltd

Company Name

Jiangxi Avonflow Hvac Tech Co., Ltd

Address

No.97, Xingye Avenue, Economic Development Zone, Shangrao City Jiangxi Province

Country

China

View All Listings by this Company

CM(E) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Maximum operating parameters: Cast iron models: Maximum working pressure 6.0 bar @ 90°C. Maximum working pressure 10.0 bar @ 40°C. Stainless steel models (not self-priming variants): Maximum working pressure 10.0 bar @ 99°C. Maximum working pressure 16.0 bar @ 90°C. Stainless steel self-priming models (CM(E) 1, 3 & 5 (AISI 304) only): Maximum working pressure 10.0 or 16.0 bar @ 60°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

251007701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” - 2” BSP (F) or NPT (F) inlet and outlet.

Marking:

Grundfos and Grundfos logo, type, model, manufacturing country and technical information on adhesive labels either on the terminal box or fan cover. Grundfos and Grundfos logo on the terminal box or fan cover.

Installation Requirements:

R001 R415

Expiry date:

31/10/2030

Model:

CM(E)1, CM(E)3 and CM(E)5: CM(E)1, cast iron / AISI304 2 – 8 stages. CM(E)3, cast iron / AISI304 2 – 8 stages. CM(E)5, cast iron / AISI304 2 – 8 stages. CM(E)1, AISI316 2 - 14 stages. CM(E)3, AISI316 2 - 14 stages. CM(E)5, AISI316 2 - 13 stages. CM(E)10 CM(E)15 and CM(E)25: CM(E)10, cast iron / AISI304 1 – 5 stages. CM(E)15, cast iron / AISI304 1 – 4 stages. CM(E)25, cast iron / AISI304 1 – 4 stages. CM(E)10, AISI316 1 – 8 stages. CM(E)15, AISI316 1 – 4 stages. CM(E)25, AISI316 1 – 4 stages. Self-priming models: CM(E)1, AISI304 3 – 6 stages (S or O) CM(E)3, AISI304 3 – 6 stages (S or O) CM(E)5, AISI304 3 – 7 stages (S or O) Model key: CM/CME X1-X2 X3 X4-X5-X6-X7-X8 X9 X10 X11 X11-X12-X13-X14 Where: CM = Centrifugal Modular. CME = Centrifugal Modular with integrated frequency converter. X1 = Rated flow rate at 50 Hz (m³/h): 1-25. X2 = Number of impellers: 1-14. X3 = Pump Versions: A - Basic Version. E: Pumps with certificates/approvals. O: Self-priming version (maximum suction lift 8 metres) (Only available on CM(E) 1, 3 & 5 stainless steel (AISI304) models). S: Self-priming version (maximum suction lift 4 metres) (Only available on CM(E) 1, 3 & 5 stainless steel (AISI304) models). X4 = Pipe connection: R: Rp (ISO 7/1). S: Internal NPT thread. X5 = Material in contact with pump media: A: inlets and outlets parts EN-GJL-200, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. G: Sleeve, Pump shaft + Impellers and chambers EN 1.4401/AISI 316. I: Sleeve, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. X6 = Rubber parts in pump (excluding neck ring and shaft seal): E: EPDM. V: FKM. X7 = Shaft seal: A: O-ring seal with fixed driver. X8 = Material of rotating seal face: Q: Silicon Carbide (SIC). X9 = Material of stationary seal face: Q: Silicon Carbide (SIC). X10 =Material of secondary seal: E: EPDM. V: FKM. X11 = Supply voltage (electrical characteristics - not relevant for the WRAS approval): A/B/B1/B2/C1/E/E1/F/G/H/J/O/S/T/U/V/X. X12 = Motor information(electrical characteristics - not relevant for the WRAS approval): A/B/C/D/EF/G/H/I/J. X13 = Mains plug (electrical characteristics - not relevant for the WRAS approval): A/B/C/D. X14 = Sensor (electrical characteristics - not relevant for the WRAS approval): N: No sensor. Example: CM 10-3 A-R-I-E-A Q Q E C1-A-A-N

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of stainless steel or cast iron (with electrolytic coating) bodied, multistage centrifugal pumps with stainless steel impellers. Maximum working pressure: Ranges from 16.0 bar to 30.0 bar (see models). Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

251108701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Hydroo, model and product information on data plate fixed on pump bracket. Flow arrow on body.

Installation Requirements:

R001 R415

Expiry date:

30/11/2030

Model:

VX1 Stainless steel Body – DIN Flange (2 to 40 stages) DN25 (PN25), VX3 Stainless steel Body – DIN Flange (2 to 31 stages) DN25 (PN25), VX5 Stainless steel Body – DIN Flange (2 to 33 stages) DN32 (PN25), VX10 Stainless steel Body – DIN Flange (1 to 22 stages) DN40 (PN25), VX15 Stainless steel Body – DIN Flange (1 to 18 stages) DN50 (PN25), VX20 Stainless steel Body – DIN Flange (1 to 17 stages) DN50 (PN25), VX32 Stainless steel Body – DIN Flange (1 to 16 stages) DN65 (PN30), VX45 Stainless steel Body – DIN Flange (1 to 13 stages) DN80 (PN30), VX65 Stainless steel Body – DIN Flange (1 to 8 stages) DN100 (PN25), VX1 Stainless steel Body – Oval Flange (2 to 26 stages) G1 (F) (PN16), VX3 Stainless steel Body – Oval Flange (2 to 20 stages) G1 (F) (PN16), VX5 Stainless steel Body – Oval Flange (2 to 20 stages) G1 1/4 (F) (PN16), VX10 Stainless steel Body – Oval Flange (2 to 14 stages) G1 1/2 (F) (PN16), VF1 Cast Iron Body – DIN Flange (2 to 40 stages) DN25 (PN25), VF3 Cast Iron Body – DIN Flange (2 to 31 stages) DN25 (PN25), VF5 Cast Iron Body – DIN Flange (2 to 33 stages) DN32 (PN25), VF10 Cast Iron Body – DIN Flange (1 to 22 stages) DN40 (PN25), VF15 Cast Iron Body – DIN Flange (1 to 18 stages) DN50 (PN25), VF20 Cast Iron Body – DIN Flange (1 to 17 stages) DN50 (PN25), VF32 Cast Iron Body – DIN Flange (1 to 16 stages) DN65 (PN30), VF45 Cast Iron Body – DIN Flange (1 to 13 stages) DN80 (PN30), VF65 Cast Iron Body – DIN Flange (1 to 8 stages) DN100 (PN25), VF1 Cast Iron Body – Oval Flange (2 to 26 stages) G1 (F) (PN16), VF3 Cast Iron Body – Oval Flange (2 to 20 stages) G1 (F) (PN16), VF5 Cast Iron Body – Oval Flange (2 to 20 stages) G1 1/4 (F) (PN16), VF10 Cast Iron Body – Oval Flange (2 to 14 stages) G1 1/2 (F) (PN16).

Approval Holder:

HYDROO PUMP INDUSTRIES S.L.

Company Name

HYDROO PUMP INDUSTRIES S.L.

Postcode

17843

Country

Spain

General Email

jordi.armengol@hydroo.com

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

31/10/2030

Notes & Further Information

The suffixes of ** represents different types of finishes as follows: C: Chrome NS: Nickel brushed RP: Red powder coated TS: Zr gold brushed RS: Rose gold brushed GS: Gold brushed GM: Gun metal brushed B: Electroplated matte black W: White CB: Matte black and chrome CW: White and chrome TG: Zr gold plated RG: Rose gold plated G: Gold plated GP: Gun metal plated BS: Gun gray brushed

Approval Holder:

Guangzhou KIND Architecture Material Technology Co., Ltd.

Company Name

Guangzhou KIND Architecture Material Technology Co., Ltd.

Address

Unit 10, No.1 Dashadi West, Huangpu District, Guangzhou, Guangdong Province

Postcode

510700

Country

China

Phone

+86-20-23371404

General Email

sale@watersino.com

View All Listings by this Company

Range of shower handsets with ABS bodies (various finishes, see model). The spray outlet is either multifunction or single function depending on series. Open outlet use only. Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

251002007

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2" BSP Male.

Marking:

KY-LIN, WRAS and DoM (YYYY.MM) on body

Installation Requirements:

R001 R040

Expiry date:

31/10/2030

Model:

W0700*,W0701*,W1300*,W1301*,W1302*,W1400*,W1502*,W1600*, W2200* & W2701* Model added January 2026 W2300* Where * denotes the finish, and can be replaced with an of the following: CHR = Chrome WHT = White BN = Brushed Nickel BLK = Black BG = Brushed Gold

Approval Holder:

KYLIN Sanitary Technology (Xiamen) Co., Ltd

Company Name

KYLIN Sanitary Technology (Xiamen) Co., Ltd

Address

No.878, Tongfu Road, Tong’an District, Xiamen City, Fujian Province

Postcode

361100

Country

China

Phone

+86 159 8082 4540

General Email

961459820@qq.com

View All Listings by this Company

Manufacturer:

KYLIN Sanitary Technology (Xiamen) Co., Ltd

Company Name

KYLIN Sanitary Technology (Xiamen) Co., Ltd

Address

No.878, Tongfu Road, Tong’an District, Xiamen City, Fujian Province

Postcode

361100

Country

China

Phone

+86 159 8082 4540

General Email

961459820@qq.com

View All Listings by this Company

Range of shower handsets with plastic bodies and various finishes. Maximum operating temperature 60 °C. Open outlet use only.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250612005

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M)

Marking:

“KEEKOE” on inlet connection.

Installation Requirements:

R001 R040

Expiry date:

30/06/2030

Model:

H01011, H01023, H02013, , H03013, H03021, H04011, H04023, H05014, H05015, H06013, H09015, H11013, H12013, H17015, H20013, H21011, H27015, H28013, H29033, H30043, H31015, H33013, H34013, H34021, H35013, H36011, H34021, H34021, H43014, H46014, H39033, H37013, H39031, H39013, H39043, H49014, H48013, H48021, H46023, H55013, H56013, H41013 & H42013.

Approval Holder:

Xiamen Keekoe Sanitary Ware Co. Ltd.

Company Name

Xiamen Keekoe Sanitary Ware Co. Ltd.

Address

No.275-279 Huanzhu Road North Jimei Industrial Zone Xiamen

Country

China

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Pull out plastic body handset for kitchen tap.

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

30/11/2030

Notes & Further Information

** Representative all models are available with the following finish code: CP-Polished Chrome BN-Brushed Nickel MB-Matte Black ORB-Oil Rubber Bronze PB-Polished Brass WP-Weathered Pewter BB-Brushed Brass

Approval Holder:

Kaiping Boyu Hose Technology Co., Ltd.

Company Name

Kaiping Boyu Hose Technology Co., Ltd.

Address

5 Dongcheng Road, Shuinuancheng, Shuikou Town, Kaiping City Guangdong Province

Country

China

View All Listings by this Company

Manufacturers:

Kaiping Boyu Hose Technology Co., Ltd.

Range of bib and hose union taps incorporating either brass or DZR brass (142HU prefix models only) bodies and non-rising spindle headworks. The FGK suffix models incorporate a ferrule guard and key (lockshield). The inlet and outlet of the 142HU (508107) and 142HU FGK (501117) models incorporate an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperatures: 142HU (508107) and 142HU FGK (508117) models 65°C, all other models 90°C.

Section:

1750 Taps

Section Subtitle:

Draw off bib tap(s)

WRAS Approval Number:

251102044

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

141 (508017), 141HU (508037), 141HU FGK (508047), 142HU (508107) and 142HU FGK (508117) models: ½” BSP (M). 141HU (508038) and 141HU FGK (508048) models: ¾” BSP (M).

Marking:

Pegler (brand of Aalberts integrated piping systems Ltd.) on spindle or lock shield.

Installation Requirements:

R001 R040

Expiry date:

30/11/2030

Model:

Bib tap: 141 (508017) Hose union bib taps: 141HU (508037), 141HU (508038), 141HU FGK (508047), 141HU FGK (508048), 142HU (508107), 142HU FGK (508117).

Approval Holder:

Aalberts Integrated Piping Systems Ltd.

Company Name

Aalberts Integrated Piping Systems Ltd.

Address

St. Catherines Avenue Doncaster South Yorkshire

Postcode

DN4 8DF

Country

United Kingdom

Phone

+447843075405

General Email

gavin.peters@aalberts-ips.com

View All Listings by this Company

Section:

1780 Taps

Description:

A Range of Hose union tap(s).

Wall Mounted Undefinable air gap see IRNs Incorporates approved single check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.

Installation Requirements:

R001 R040 R060

Expiry date:

30/11/2030

Approval Holder:

Zhejiang Valogin Technology Co., Ltd.

Company Name

Zhejiang Valogin Technology Co., Ltd.

Address

Qinggang Technological Industrial Zone Yuhuan, Zhejiang

Country

China

View All Listings by this Company

Manufacturers:

Zhejiang Valogin Technology Co., Ltd.

Section:

1800 Taps

Description:

A Range of Pillar tap(s).

Deck mounted. Capable of achieving AUK2 Tap Gap.

Installation Requirements:

R001 R005

Expiry date:

31/10/2030

Notes & Further Information

X XXX Denotes the following: First X: Different handle option and the second, third & fourth XXX for different finishes: Handles: A – Single lever type Chrome – No suffix, brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1

Approval Holder:

PPI Xiamen Industry Co., Ltd.

Company Name

PPI Xiamen Industry Co., Ltd.

Address

No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen

Postcode

361022

Country

China

General Email

heatheryang@xmppi.com

View All Listings by this Company

Manufacturers:

PPI XIAMEN INDUSTRY CO LTD

‘TAQ PEX’ range of PEX lined flexible hose assemblies with either stainless steel braiding or grey polymeric (PET - Polyethylene terephthalate) braiding. G3/8" captive nut connection includes an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Hoses with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

260104006

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Tucai, WRAS, size, year of manufacture (YY), manufacturing company (NT or TB) on ferrule.

Installation Requirements:

R001 R008

Expiry date:

31/01/2031

Model:

TAQ PEX DN6 (stainless steel braiding) TAQ PEX ACB DN6 (PET -Polyethylene terephthalate braiding). TAQ PEX DN8 (stainless steel braiding). TAQ PEX ACB DN8 (PET -Polyethylene terephthalate braiding). Available end connections: (Liso) Pipe end 8mm (Liso) Pipe end 10mm (Liso) Pipe end 15mm (Liso) Pipe end 9.6 captive nut 1/2-14 NPSM captive nut 7/16 captive nut 9/16-24UNEF captive nut G1/2" captive nut G3/4" captive nut G3/8" captive nut G3/8" valve captive nut M15x1 Clip 10 clip 11 Clip 8 Clip 9 compressor fitting 10mm compressor fitting 12mm compressor fitting 15mm Elbow 90º captive nut G1/2" Elbow 90º captive nut G3/4" Elbow 90º captive nut G3/8" External thread 1/8-27 NPSM External thread 7/16 External thread G1/2" External thread G3/8" External thread M10x1 External thread M11x1 External thread M12x1 External thread M15x1 External thread M16x1 External thread M8x1 External thread M8x1,25 External thread R1/2" External thread R3/8"

Approval Holder:

Tucai, S.A.

Company Name

Tucai, S.A.

Address

Llobateras, 10-12. Polígono Industrial Santiga, 08210 Barberà del Vallès (Barcelona)

Country

Spain

Phone

+34 93 718 95 62

General Email

info@tucai.com

View All Listings by this Company