Wall mounted, thermostatic shower valves, (chrome plated brass body), incorporating a single sequential headwork controlling both flow and temperature with a single lever operating member. Maximum working pressure: 10.0 bar Maximum operating temperature: 65°C
Range of concealed and exposed thermostatic shower valves, (chrome plated brass bodies and trim sets), incorporating quarter turn ceramic disc diverter valves with cross top operating members controlling the flow to either 1, 2 or 3 outlets (see models). The temperature is controlled independently via a thermostatic cartridge with a single lever operating member. Maximum working pressure 5 bar. Maximum operating temperature 48°C
Range of wall mounted thermostatic blending valves (chrome plated brass), incorporating ceramic cartridge headworks (see models). The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button, with a variety of operating members. The inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection with stainless-steel strainers. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted thermostatic shower valves, (chromium plated brass), incorporating a thermostatic cartridge which controls both flow and temperature. All models have a single lever operating member controlling the flow and either a single lever operating member (gr-sk-01, gr-sk-04 and gr-sk-11 models) or a cross-top operating member (gr-sk-06 and gr-sk-07 models) controlling the temperature. All models, except the gr-sk-11 model, includes a manual override button on the temperature control. Each inlet incorporates a stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spring loaded, non-return valves with ductile iron bodies (blue epoxy powder coated) with stainless steel discs, springs and shafts and EPDM seat. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Pressure relief valves with a brass body incorporating EPDM ‘O’ rings for 35890040 and EPDM diaphragm for 35900040, pre-set at 3.0 bar. Model 35890040 incorporates a manually operated lever type lifting gear Maximum working pressure 10 bar. Maximum operating temperature 90°C.
Range of pre-set pressure relief valves (spring loaded) with DZR brass body. Model 03521547 is set at 4.75 bar, 03521590 is set at 6.0 bar and 03541545 is set at 3.0 bar. Maximum operating temperature 85°C.
Range of bronze swing gate valves with bronze bodies and discs (with a metal-to-metal seal). Maximum working pressure 20.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of bronze swing gate valves with bronze bodies and discs (with a metal-to-metal seal). Maximum working pressure 20.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of single lever ball valves with stainless steel bodies, ball, EPDM O-rings and PTFE gaskets. The press fit connection is to be used with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of lever or butterfly lever operated spherical valves, incorporating a nickel plated brass body and stainless steel ball, PTFE seats and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of TH profile pressfit brass bodied spherical valves with brass balls, EPDM O-rings and lever type operating members. Fittings for use with EN ISO 21003 Pert-al-Pert Multilayer pipe. Maximum working pressure 10 bar. Maximum operating temperature 95°C.
Range of spherical servicing valves with brass bodies and chrome plated brass balls, PTFE seats, FKM rubber ‘O’-rings and lever operating members. Maximum working pressure 40 bar. Cold water use only.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of bronze bodied gate valves incorporating brass wedges with PTFE packing. Maximum Pressure 16.0 bar. Maximum operating temperature 100°C.
Range of hand wheel operated gate valves with brass bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with DZR brass bodies, stems and discs. The valves operate via a hand wheel (non-rising) and a metal to metal seal. Valves are for above ground use only. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
KM10 range of gate valves with either brass or DZR brass (from October 2023) bodies and PTFE washers. Valves are operated via a non-rising spindle headwork. Maximum operating pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass stop valves with non-rising stems, having brass bodies, EPDM ‘O’ rings and PTFE gaskets and various operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of EBCO stop valves with gunmetal bodies with a various end connections. Maximum working pressure 16 bar. Cold water use only.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Activflo Lite range of water conditioners with copper bodies. Models with compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
“CN Pressure vessel” range incorporating a HDPE liner. The products have a separate outer layer (with black, blue, grey or natural finishes). The CN Pressure vessel 24x72” D-4 model has a top and bottom opening. Maximum operating pressure 10.5 bar. Cold water use only.
'ABS-040 Black'. Black coloured, injection moulded ABS material. For use with water up to 85°C.
'WHC1850'. White coloured, dry pressed ceramic disc. For use with water up to 85°C.
'Relithane 151. Factory applied, brown coloured, two-component Polyurethane coating. Mix base and hardener in a 2.5:1 ratio and apply as per manufacturer's 'Standard Operating Procedure & Guidelines, Revision 2, 157/2022' dated 12th October 2022. Cure for 40 seconds@35°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBVL EX400G – RAL 5005 Blue & RAL 5017 Blue'. Factory applied, blue coloured epoxy coatings. Apply as per manufacturer’s datasheet ‘PDS/APPPG/V01/01-2024’. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'APCOSHIELD FBPC EX405SG INTER GREEN'. Factory applied, green coloured epoxy coating. Apply as per manufacturer's data sheet 'PDS/APPPG/V02/01-2024'. Post-cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pentaline 1000 HT Red'. Factory applied, red coloured (once mixed), two-component epoxy coating. Mix base and hardener in a volume ratio of 3:1 and apply as per manufacturer's instructions 'Chembur R&D/PI/23/02' dated 28/12/2023. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotun Marathon IQ2'. Factory applied, two-component, grey coloured epoxy coating. Mix parts A:B in a ratio of 3:1 parts and apply as per 'Jotun Marathon IQ2' Technical Data Sheet dated '16 April 2021'. Cure for 7 days@23°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'G52-06 Quick-drying type Black High Chlorinated Polyethylene Anticorrosive Coating'. Factory applied, black coloured polyethylene coating. Apply as per manufacturer's data sheet 'XYJSMS002', dated January 10th, 2023. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SUS-GRP01'. White coloured GRP panel manufactured by hot press moulding. For use with water up to 65°C.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Binh Minh Plastic's HDPE pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 40°C.
'Cosmoplast HDPE Pressure Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 65°C.
‘METOLUX Metoset’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'version 2', dated 29.10.2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WRWNR75D - HT'. Black coloured, natural rubber material manufactured by calendaring and moulding. Shore hardness 75 Shore D. Tested in-radius size 1.25mm. For use with water up to 50°C.
'WRAS 61713 EB 78'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 78D. Tested in-radius size 1.05mm. For use with water up to 60°C.
'WRAS 61813 E80'. Black coloured, hard ebonite rubber material manufactured by calendaring and autoclave vulcanisation. Shore hardness 80. Tested in-radius size 2.2mm. For use with water up to 60°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SME001 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 60. In November 2024 'SME001 EPDM', a compression moulded EPDM rubber with a shore hardness of 75 was added to the approval so that a range with a hardness between 60 & 75 is covered by the approval. Tested in-radius size of 1.0mm and are for use with water up to 65°C.
'E59WKZ'. Black coloured, injection moulded EPDM rubber material. Shore hardness 58. Tested in-radius 1.0mm. For use with water up to 60°C.
'2MS70-55R Seals, Washers, Gaskets and 'O' rings'. Red coloured, injection moulded silicone seals, washers, gaskets and 'O' rings. Shore hardness 70. Seals have a tested in-radius size between 0.25mm & 8,0mm. Washers, gaskets and 'O' rings have a tested in-radius size of 8.0mm. For use with water up to 85°C.
'HCR 9230, HCR 9250, HCR 9270 & HCR 9280'. Natural (appear white, translucent), compression moulded silicone rubber materials. Shore hardness between 30 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘Trutite Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.3’, dated 12/02/24 and this material is only approved for these conditions. For use with water up to 85°C.
‘CORE® Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.2’, dated 12/01/23 and this material is only approved for these conditions. For use with water up to 85°C.
Page 148 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
