Range of angled and straight ball valves with plastic valve bodies, PTFE seats and EPDM O-rings. Maximum working pressure 16 bar. Maximum operating temperature 40°C
Range of gate valves, (brass bodies) controlled via a handwheel with PTFE seals. Maximum working pressure 20.0 bar (L198 models), 16.0 bar (L197 & P474 models). Maximum operating temperature 99°C
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per manufacturer's technical data sheet 'FBE/ REV00 01-02-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies. Incorporating a solenoid valve activated via an infra-red sensor. The inlets to the control box incorporate stainless steel strainers and the outlet incorporates a plastic aerator. Maximum working pressure: 8 Bar Maximum operating temperature: 65°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Range of single hole, single outlet fixed (over the rim swivel nozzle) bidet combination tap assemblies stainless steel or brass bodies with various finishes, incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a swivel nozzle with a plastic aerator. The products are also supplied with a lever type pop-up waste. Maximum working pressure 3.0 Bar Maximum operating temperature 60.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MIO BAS C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Aerator | Click Type | |
| HMS MIO BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener | ||
| CN SPH BASNW C | Chrome | G 1/2" Female | 5 bar | 60 °C | Bristan | Body | No | Ceramic cartridge | C-plate | Flow Straightener |
HMS MIO BASNW C - (selling code for Homeserve without Waste) CN SPH BASNW C - (selling code for Crest without Waste) Model MIO BAS C includes an aerator with 4.5lpm flow limiter - flow limiter performance is not tested as part of the regulators specification.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 193938 X XXX | VARIOUS | ½” BSP | 5.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 194828 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type | |
| 181028 X XXX | VARIOUS | ½” BSP | 10.0 bar | 65 °C | PPI | BODY | No | Ceramic cartridge | C-plate | Aerator & Flow Straightener | Click Type |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes, see model), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 197021 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | Non-rising spindle | C-plate | Aerator & Flow Straightener | |
| 207121 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener | |
| 207125 X XXX | VARIOUS | 1/2" BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/2 Turn ceramic disk | C-plate | Aerator & Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Cross top Dome or Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Floor standing, single hole, single outlet (swivel) combination tap assembly with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to a shower outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with dome operating members. The spout outlets incorporate plastic aerators or flow straighteners. The product is supplied with metal back nuts. Maximum working pressure – 10.0 Bar Maximum operating temperature - 70 °C
Range of wall mounted, concealed, two-hole single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with single lever operating members. The concealed body is either brass (UBR0257) or nickel plated brass (all other models). The spout and trim set have brass bodies with various finishes, see model. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperatures 65°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193706 X XXX | VARIOUS | ¾” BSP (M) | 10.0 bar | 85 °C | PPI | Rear of tap body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : H (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193805 X XXX | VARIOUS | ¾” BSP | 10 bar | 65 °C | PPI | BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Aerator | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193705 X XXX | VARIOUS | ¾” BSP | 10.0 bar | 65 °C | PPI | Rear of body | No | 1/4 Turn ceramic disk | Metal Backnuts | Flow Straightener | Flow Regulator Fitted, Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle option = and the second, third & fourth XXX for different finishes: Handles : A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of two hole, double outlet (swivel) combination tap assemblies (chromium plated brass). The TAP2014 model incorporates non-rising spindle headworks with dome type operating members. The TAP 9023 model incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener. The products are supplied with metal backnuts. Maximum working pressure 5.5 bar. Maximum operating temperature 70°C.
Range of three hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with various operating members. The spout outlet incorporates a plastic aerator. The product incorporates stainless steel or nylon braided EPDM connection hoses. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C
Range of three-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headwork with either single lever, dome, wheel or cross top operating members. The headworks are connected to the spout with stainless steel braided braided PEX lined flexible hose assemblies. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed thermostatic basin mixing valves with brass bodies. Temperature is controlled via a thermostatic cartridge and flow is controlled by solenoid valves actuated by an infrared sensor. The outlet incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of in-line water filters with plastic bodies. Maximum working pressure 8.0 bar. Cold water use only.
‘APL’ & 'AP' ranges of brass press fittings for use with ‘APE Multylayer' pipe. Connection is achieved via TH or U profile press jaws. AP range, only TH profile; APL range, TH and H profile; TH and H profile from DN 16 to DN32; TH for DN40, DN50 and DN63. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of press fittings (brass bodies - various finishes) with stainless steel press (‘TH’ profile) collars and EPDM O-rings for use with “VMA” range of PEX/AL/PEX multilayer pipe (for press fitting connections and compression for adaptor fittings only) or copper pipe manufactured to EN1057 (compression connections). Maximum operating temperature: 95°C. Maximum operating pressure: 10 bar.
Instantor range of copper press fittings with an EPDM ‘O’-ring for use with copper pipe to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings for use with stainless steel pipe. Above ground use only. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of stainless-steel press fittings with EPDM ‘O’-rings and EPDM washers. For use with stainless-steel pipe. Joints are achieved using a press fitting tool. Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C.
‘EPH_WSP19_XXXX’ range of brass caplillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of brass fittings with compression connections to be used with copper pipes EN 1057. For above ground use only. Maximum working pressure 6.0 bar. Maximum operating temperature 95°C.
‘Flowflex,’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
‘CFxx and TFxx’ range of brass compression fittings for use with copper pipes and Irish copper pipe (both manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: CF15 and CF16 models: 65°C. All other models: 85°C.
‘Instantor Lead-Free Brass’ compression fittings with DZR brass body, for use with DZR Copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
‘Universal Transition Coupling (UTC)’ range of plastic compression fittings for use with the following pipe types and sizes: Stainless steel (manufactured to ASTM A554/ BS EN 10312): ¾”, 1” & 1¼”. Galvanised (EN 10255): ¾”, 1”, 1¼”, 1½” & 2”. Copper (BS EN 1057): 15mm, 22mm & 28mm. PVC (BS EN 1452): 20mm & 2”. ABS (BS 5391-1): 20mm, 25mm & 32mm. PE80 & PE100 pipe (to BS EN 12201): 20mm, 25mm, 32mm, 50mm & 63mm. For use above and below ground. Maximum working pressure 12.5 bar. Cold water use only.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
‘EPH_WSP19_XXXX’ range of brass end feed and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of inline water meters with brass bodies (blue or red epoxy coating). The inlet incorporates a plastic strainer. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
‘Altair V4’ range of in-line and manifold volumetric water meters with brass or plastic bodies (see models), the products can be provided with a plastic strainer. Maximum working pressure 16.0 bar. Cold water use only.
Range of ultrasonic water meters with plastic bodies and plastic strainers at the inlets. Specific models (see models) incorporate an optional non return valve (not suitable for backflow protection). Maximum working pressure 16.0 Bar. Maximum operating temperature 90°C.
Range of water meters with brass bodies, plastic turbines and plastic strainers on inlets. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Page 14 of 19
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
