'Xytron™ G3010E BK00001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'F1520'. Blue-grey coloured PTFE material manufactured by ram extrusion. For use with water up to 85°C.
'National Plastic Sharjah-LF PVC Pipe' & 'National Plastic Al Ain, Abu Dhabi-LF PVC Pipe'. Grey coloured, extruded PVC pipes. For use with water up to 60°C.
'Art. 0985077200'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
‘DEWALT PV60-PRO’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1, version 16/01/2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MIT-SVE'. Site applied, two part, anchor resin. 'MIT-SVE' is grey coloured when mixed and consists of Part A (shiny white liquid) & Part B (shiny black liquid). Mix, apply and cure as per manufacturer’s product information sheet 'EN 02/2023'. For use with water up to 60°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'EPDM 70.10-02 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
'GM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.15mm. For use with water up to 23°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 70.503-00'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated). Flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. Spout outlet incorporates plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies with brass bodies (chrome plated), The flow is controlled by a solenoid valve activated via an infra-red sensor. The product incorporates a manual temperature control operated by a single lever on the side of the body. Spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of deck mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. There is no temperature control or operating member for these products. The spout outlet incorporates a plastic aerator. The products supplied with a plastic flow regulator. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Wall mounted, single hole, single outlet (fixed) electronically controlled combination tap assemblies (brushed stainless steel). The flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. There is no temperature control or operating member for these products. The spout outlet incorporates a plastic aerator. The products supplied with a plastic flow regulator. Maximum working pressure 6.0 bar.
Non-metallic materials and components comply with BS6920 at 40°C
Range of wall mounted single-hole, single outlet, fixed electronically controlled combination tap assemblies (chrome plated brass), incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of side and bottom entry BS1212-4 fill valves with plastic bodies. Maximum working pressure 10.0 bar. Coldwater use only.
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Maximum working pressure - 10 Bar Maximum operating temperature – Cold water use only.
Concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3.5 litres. The cistern is operated by an electronically controlled flush valve. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of spring loaded resilient trim check valve cartridges with acetal body and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of tundishes with plastic bodies. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of insulated, black coloured polyethylene storage cisterns suitable for storing non-wholesome water. The cisterns incorporate an AB air gap arrangement with a meshed weir overflow arrangement. The cisterns are supplied with a float valve and blue plastic float. Cold water use only.
Range of quarter turn ceramic disc and ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Thermostatic cartridge with a brass body and EDPM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of thermostatic cartridges with brass or plastic bodies (see model) incorporating a stainless-steel strainer and EPDM ‘O’-rings. Maximum working pressure 10.0 Bar. Temperature: 75°C – GR-FX-X05S, GR-FX-01S, GR-FX-13T & GR-FX-X08. 65°C - GR-FX-04S & GR-FX-02TF.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet is a pull-out spray type. The spout inlets incorporate approved check valve cartridges; however, the complete assembly has not been tested to demonstrate it provides backflow prevention. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass). Incorporating quarter turn ceramic disc headworks with single lever operating members. The spout is a pull-down hose and handset with an optional spray function. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes, see models), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Model V110V2-XX also comes supplied with a lever operated pop up waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headworks and single lever operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (model M101086) or 85°C (all other models).
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with lever type pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature (See models)
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet combination tap assemblies, (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single hole, single outlet fixed combination tap assemblies, (chrome plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet incorporates a plastic aerator. Models (63301, 63501, 63303, 63503, 63305 & 63505 are supplied with lever operated pop-up waste) Maximum working pressure 5 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating members on models (295385, 295409, 295412,). Model (295316) incorporates quarter turn ceramic disc headworks with cross-top operating members. The spout outlets incorporate plastic flow straighteners or aerators. The products are supplied with approved click type wastes, verified by test. Model (295316) can also be supplied with a lever operated pop-up waste. Maximum working pressure - 10.0 Bar (295316) Maximum working pressure - 5.0 Bar (295385, 295409, 295412) Maximum operating temperature 65.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass body, various finishes) , incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. The products are supplied with a lever type pop-up waste. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (various finishes). Incorporating ceramic cartridge headworks, and single lever operating members. The spout outlet incorporates a plastic aerator. Supplied with an open waste outlet. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass body, chrome or black finish) incorporating ceramic cartridge headworks and single lever operating members. The spout outlet incorporates a spring-loaded pull-down hose incorporating a spray handset with trigger mechanism that controls the spray. The spray handset incorporates a plastic aerator at the outlet. Maximum working pressure 5 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel), combination tap assemblies (brass bodies with various finishes), incorporating ceramic cartridge or quarter turn ceramic disc headworks with single lever, cross-top or dome operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 or 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet, swivel, combination tap assemblies in chromium plated brass. The models incorporate a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating ceramic cartridge headwork with single lever operating members controls the flow of hot and cold water. A quarter turn ceramic disc headwork with single lever operating member which incorporates a manual override button, controls the flow of near-boiling water The spout outlets incorporate a plastic areator. Maximum working pressure: hot and cold water = 8.0 bar. Maximum operating temperature hot and cold water circuit is 65°C. Maximum operating temperature of near-boiling water circuit 100°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a ceramic cartridge headworks and single lever operating member. Products are supplied with lever operated pop-up wastes and spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) with a ceramic cartridge headwork with a single lever operating member The spout outlets incorporate plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floor mounted single hole, single outlet (swivel), combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. This product is supplied with shower hose, shower handset and PEX inner-lined braided inlet hoses. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Page 107 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
