Range of stainless steel, stainless steel with nylon or nylon braided, EPDM lined hose assemblies. Some models incorporate servicing valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel braided EPDM lined flexible hose assemblies with EPDM seals, available with a variety of end connections, some of which include isolation valves (see model). Maximum working pressure 10 Bar. Maximum operating temperature 85°C
Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only
Range of stainless-steel or nylon braided PEX lined hoses, incorporating EPDM O-ring or gaskets. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of chromium plated interlocked, PEX lined shower hoses with EPDM rubber gaskets. Maximum operating pressure: 6.0 bar. Maximum operating temperature 85°C.
Range of Indirect and direct unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 6.0 bar at 90˚C and an expansion relief valve set at 4.5 bar. The product is supplied with a safety group consisting of a pressure reducing valve set at 3.0 bar, and an approved check cartridge, verified by test (suitable for backflow protection against fluid category 2) an expansion vessel and tundish. Maximum working pressure: Secondary: 4.0 Bar Primary: 3.0 Maximum operating temperature 99.0°C
Range of wall mounted, concealed, manually operated blending valves with brass bodies (various finish trim kits - see model) incorporating a ceramic cartridge headwork with a single lever operating member. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, concealed, manual blending shower valves with brass bodies (various finishes), incorporating a ceramic cartridge headwork and various single lever operating members. The product is also supplied with ¾” BSP (M) x ½” BSP (F) adaptors. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Range of T-type thermostatic mixing valves with brushed chrome plated DZR brass bodies for use with copper pipe (manufactured to BS EN 1057). The inlets of the PEG prefix models incorporate a check valve cartridge verified by test (suitable for backflow protection against Fluid Category 2). The inlets of the TX prefix models incorporate an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. UA & UAX suffix models incorporate isolation valves on each inlet, which includes a cold through connection on the UAX models. All inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, concealed, thermostatic shower blending valves (brass bodies – various finishes), The flow is controlled via a 2 way manually operated diverter to the shower outlets. Temperature is controlled via a thermostatic cartridge incorporating a manual override button. The trim sets are provided with dome type operating members. The inlets incorporate an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Wall mounted, concealed, thermostatic blending valve (brass body) with a chromium plated trim set incorporating a single sequential headwork controlling flow and temperature with a single lever operating member. The product also incorporates approved check valve cartridges, however, the complete product has not been fully tested to demonstrate they provide backflow protection. The product is supplied with a combined strainer/isolation valve for each inlet. To be used with copper pipe manufactured to EN 1057. Maximum working pressure; 10 bar. Maximum operating temperature 65°C.
Range of T-type thermostatic mixing valves with DZR brass bodies. Temperature is pre-set under a fixed cap. The inlet adaptors incorporate single check valve cartridges (verified by test, suitable for backflow protection against Fluid Category 2) and stainless-steel strainers. The inlet adaptors for models 400MX15CP & 400MX22CP are 90° elbows instead of straight adaptors and incorporate additional integral spherical valves. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Range of butterfly valves with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. Gearbox and handwheel Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of wafer, lugged and flanged butterfly valves with blue epoxy coated ductile iron bodies, zinc coated (galvanised) discs and EPDM seats. UWBV-4, LWBV-V4 & FBV-4 models incorporate a hand wheel operating members and UWBV-34, LWBV-3V4 & FBV-34 incorporate a worm gear operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of piston type float operated inlet valves with brass bodies. The valves discharge from a downwards atmospheric discharge arrangement on the underside of the body. Maximum working pressure: 3.0 (1MFVLP104 models only) or 14.0 Bar (all other models) Cold water use only.
Range of spherical valves incorporating nickel plated (brass bodies with chrome plated brass ball and operated via lever, handle or screwdriver slot. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of lever or butterfly operated spherical valves with brass or nickel-plated brass or DZR brass bodies models Models M69150000LPDZR & M69220000FBDZR . Incorporating brass or nickel-plated brass or DZR brass ball. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 Bar. Maximum operating temperature 99.0°C
Range of lever or butterfly operated spherical valves with brass or nickel plate bodies and ball. Maximum working pressure 40.0 Bar Maximum operating temperature 99.0°C
Range of spherical valves incorporating DZR brass body, plastic ball and lever type operating members. The products also incorporate a drain valve. Maximum working pressure 10.0 bar. Cold water use only.
Range of spherical valves incorporating a DZR brass body, brass ball (¼”-1¼”) or DZR brass ball (1½”-2”) (all chrome plated), PTFE seats and FKM ‘O’-rings. Maximum operating pressures: ¼” - 1¼”: 40.0 bar. 1½” - 2”: 32.0 bar. Maximum operating temperature 100°C.
Range of spherical valves with stainless steel bodies, incorporating PTFE seats and a lever t operating member. Maximum working pressure: 68 Bar. Maximum operating temperature: 100°C
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM discs and non-rising spindles with hand wheel operating members. Maximum working pressure 10.0 Bar Maximum operating temperature 80.0°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM rubber coated wedges and non-rising spindles with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C.
Range of double regulating valves incorporating bronze bodies with two test ports. Valves are adjusted using a handwheel. Maximum operating pressure: 25 bar. Maximum operating temperature: 85°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purolite C104EPLUS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ultradur® B4520 FC Aqua uncolored'. Uncoloured (appears white), injection moulded PBT materials. For use with water up to 23°C.
'VIALLI-De SDR 6 & SDR 7.4 PPR pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 & SDR 7.4 Pipes with Glass Fibre Middle Layer'. Extruded PPR pipes with a green coloured inner and outer layer and a red coloured, glass fibre middle layer. For use with water up to 23°C.
'Ultrason® S 2010 G4'. Light beige coloured, injection moulded polysulphone material. For use with water up to 85°C
'662016, 662014, 662062 & 662061'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'EPDM4570‐70'. Black coloured, compression moulded gaskets. Shore hardness 70. Tested in-radius 2.0mm. For use with water up to 85°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
Page 84 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
