Range of non-return, swing gate valves with blue epoxy powder coated, ductile iron bodies and EPDM rubber valve seats. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.
Range of non return valves with bronze bodies and discs, and an EPDM washer. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of in-line adjustable pressure reducing valves with DZR brass bodies and EPDM ‘O’-rings and gaskets, for use with copper pipe (manufactured to EN1057). The valves incorporate test ports at the outlet. The product is supplied with an optional pressure gauge. The outlet pressure is adjustable between 1.0 bar and 6.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 80°C.
Pressure relief valve with a plastic body and EPDM diaphragm with manual easing gear. Pre-set at 3.0 bar. Model 31030030 is pre-set at 2.5 bar. Model 31030070 is pre-set at 4.5 bar. Maximum operating temperature 90°C.
Range of latching and non-latching solenoid valves with a plastic body (all models, except for 07230017 & 07230018 models added September 2023) and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of lever operated spherical valves with nickel plated brass bodies incorporating chromium plated brass balls. For use with copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of ball valves with nickel plated brass bodies, chrome plated brass ball, PTFE seats, and either lever or T handle operating members (see models). Maximum working pressure 16.0 to 64.0 Bar (Size & model dependant, see models) Maximum working temp 85°C
Spherical valve with DZR brass body and butterfly operating member, for use with copper tube (manufactured to EN 1057). The valve incorporates a drain valve. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C
Angled spherical valve with brushed chrome plated brass body, chrome plated, brass ball, and single lever operating member. The product incorporates a stainless steel filter. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of lever operated spherical valves with brass bodies (nickel plated), chrome plated brass balls, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies, brass ball, and EPDM ‘O’-rings. Compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with Brushed chrome plated brass body and chrome plated brass ball. Some models incorporate an actuator (please refer to model). Please refer to model for maximum working pressure. Maximum operating temperature 100°C
Lever operated spherical valve with brushed chrome brass body, EPDM O-rings and PTFE gaskets. The valve incorporates a stainless steel filter with EPDM O-ring and brass filter plug. The compression connection is to be used with for polyethylene pipe PE100 to EN12201. Maximum working pressure 25.0 bar. Cold water use only.
Range of lever or butterfly operated spherical valves with nickel plated brass bodies and brass ball with PTFE seat. Valves to be used with EN1057 copper pipe. Maximum working pressure: 25.0 Bar Maximum operating temperature: 85°C
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies, and an EPDM wedge, gasket and ‘O’-ring. The 3233 model has a rising spindle, the 3243 model has a non-rising spindle, both have a handwheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an EDPM wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 10.0 bar. Maximum working temperature 65°C
Range of gate valves with a non-rising spindle and a handwheel operating member. The 8510 suffix models have a brass body and brass wedge, the 8511 suffix models have a DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy powder coated, ductile iron wedge and bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C
Range of gate valves with brass bodies and wedge with either a lock shield or non-rising spindle operating mechanism for use with copper pipe (manufactured to EN 1057). Maximum working pressure 6.0 Bar Maximum operating temperature 95.
Range of screw down stop valves with brass bodies and bonnets and EPDM seats. Maximum working pressure 20.0 bar. Cold water use only.
Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.
‘Sleeve for Pipe M. Bottom Filter Nozzles DM, DS & D8. Upper Filter Nozzles AD, AP, AM & AS. Collector CB06, CB08, CC06 & CC12. Filter Nozzles P6 & P5’. Natural (appear white in colour) & red coloured, injection moulded ABS components. For use with water up to 23°C.
'Endolac 245.30 FGC'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's technical data sheet dated 04/05/2022. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Carbongraphite AG21 P/T, MCI320/T & AG21P-3M/T. Dark grey coloured, phenolic resin filled, carbon graphite rings manufactured by cold pressing. For use with water up to 85°C.
'MAT901 & MAT902'. In June 2025 ‘MAT901IT & MAT902IT’ washers were added to the approval. Black coloured carbon/PTFE washers manufactured by pressing. For use with water up to 85°C.
‘Sonergy AW008’. White coloured, compression moulded ceramic material. For use with water up to 85°C.
'EVER-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'JSP-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Myungjin GRP Water Tank Panel'. Light grey coloured, hot pressed GRP panel. For use with water up to 50°C.
'YD-PEX' hose. Natural (white coloured), extruded single layered PEX hose. In May 2024 ‘YD-PEX-BL’ hose was added to the approval. Black coloured, extruded, single layered PEX hose. Both are for use with water up to 85°C.
'Silicopaste 312500'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'4MID 9B22150 W-A BBK'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
'POLYPOL-1045'. Yellow coloured, contact moulded Isophthalic Unsaturated Polyester Resin material. For use with water up to 50°C.
'Jain HDPE (PE 100) Black Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 60°C.
‘VP1620-WR & VP-2020-WR’. Single layer, cream coloured, extruded PEX-b tubes. For use with water up to 85°C.
‘Dowlex 2631UE & Dowlex 2631.10UE’ Natural (appear white coloured). ‘RX 102 Natural, RX 102 Black 9003 & RX 102 GR Black 9003’ (black coloured). In April 2025 ‘RX102 Blue 6263’ (blue coloured) was added to the approval. Rotationally moulded polyethylene materials. For use with water up to 70°C
‘Dowlex 2629UE & Dowlex 2629.10UE’. ‘RX 101 Natural, RX 101 Black 9003 & RX 101 GR Black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Dowlex XZ89342.00 & Dowlex XZ89342.10’. ‘RX 137 Natural, RX 137GR black 9003 & RX 137 black 9003’. Natural (appears white coloured) and black coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Sabic R50035EE’. ‘RX 806 Natural, RX 806 Black 9003, RX 806GR Black 9003, RX 820 Light Blue 6001 & RX 820GR Light Blue 6001’. Natural (appears white coloured), black and light blue coloured, rotationally moulded polyethylene materials. For use with water up to 70°C.
‘Borsafe HE3494-LS-HP’. Blue coloured HDPE material for injection moulding and extrusion. ‘Borsafe HE3490-LS-HP & Borsafe HE3490-LS-HW’. Black coloured, HDPE materials for injection moulding and extrusion. ‘Borsafe HE3490-IM-W’. Black coloured, HDPE material for injection moulding. ‘Borsafe HE3490-SLS-H’. Black coloured, HDPE material for extrusion. All grades are for use with water up to 60°C.
'BorSafe ME3440 (black)'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'BorSafe HE3490-LSH'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
‘4TECH 9S22110 W-A ANL, 4TECH 9S22120 W-A ANL & 4TECH 9S22130 W-A ANL’: Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
‘Wouper EG30WF, EG40WF & EG50WF’. Injection moulded, glass filled (30% - 50%) PPA materials available in natural (appears off-white), black and grey. ‘Wouper EG30WF, EG40WF & EG50WF’ natural, black & grey are for use with water up to 85°C. ‘Wouper AG30WF’. Injection moulded, glass filled (30%) PPA materials available in natural (appears off-white), black & grey. ‘Wouper AG30WF’ natural & black are for use with water up to 85°C. Between July 2022 and January 2023, ‘Wouper AG30WF’ grey is for use with water up to 23°C. From February 2023, ‘Wouper AG30WF’ grey is for use with water up to 85°C.
'ABR-PS'. Black coloured, injection moulded polystyrene material. Between July 2022 and 14th February 2023, the material is for use with water up to 23°C. From 15th February 2023 until July 2027, the material is for use with water up to 60°C.
Page 72 of 233
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
