Range of wafer, lugged and double flanged type butterfly valves (with blue epoxy coated ductile iron bodies, and either a stainless steel or grey epoxy coated ductile iron disc with an EPDM liner. Maximum working pressure 16.0 Bar (DN50 to DN800) or 10.0 Bar (DN900 to DN1200)
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with handwheel gear operating members. Maximum working pressure – 10 bar or 16 bar, see models. Maximum operating temperature – 23°C.
Range of high and low pressure diaphragm float operated valves with brass body and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Range of piston type float operated inlet valves with brass bodies and backnuts. Maximum working pressure 8.0 or 10.0 bar (please refer to model). Cold water use only.
Wall mounted, shower control valve, (brass body – various finishes), incorporating a half turn ceramic disc headwork using a dome type operating member. The shower outlet connection incorporates an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 10 bar. Maximum operating temperature 70°C
Range of pre-set pressure relief valves (set at 3.0 bar) with nylon bodies, EPDM diaphragms and ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass or DZR brass spherical valves incorporating single lever operating members and a chrome plated brass ball. Model 0312A030307DC is an angled 90-degree valve which incorporates single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 or 3). For use with EN1057 copper pipe. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of spherical valves with nickel plated brass bodies and brass balls, incorporating PTFE washers. R950W models are lever operated and R951W models have a butterfly operating member. Maximum working pressure is either 42.0 bar (up to and including ¾”) or 35.0 bar (up to and including 2”). Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of lever operated, full bore spherical valves with brass bodies (brushed chrome) andchrome plated brass balls and a range of different operating members. Sizes ¼” to ½” have a maximum working pressure of 64.0 bar. Sizes ¾” to 2½” have a maximum working pressure of 40.0 bar. Cold water use only.
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
‘3029’ range of lever operated spherical valves with chromium plated brass bodies and balls, incorporating PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of gate valves with bronze bodies and bronze wedges. The valves operate via non-rising spindle head work with hand wheel or lock shield operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of brass and DZR brass stopcock incorporating EPDM and PTFE washers. Compression connections, to be used with copper pipe EN1057 only. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of manually operated balancing valves with either a DZR brass or bronze body incorporating a non-rising spindle balancing mechanism. Valves are adjusted using a handwheel. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of commercial, salt regenerated, electronically controlled ion exchange water softeners. Maximum working pressure 7.0 bar. Cold water use only.
Non-metallic materials and components comply with BS6920 at Cold water use only°C
'SSIC-C/S1.S9.S12'. Grey coloured carbon graphite/silicon carbide ceramic ring manufactured by sintering. For use with water up to 85°C.
'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'TP12939 Natural'. Natural (appears off-white) polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'TP12978 Black'. Black coloured, polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'Ganga 50, 60, 70, 80 & 90'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 90 ShA. Tested in-radius size 1.1mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 23°C.
'TamAcryl 2000 Orange or Blue with corrosion inhibitor', orange coloured or blue coloured (once mixed), site applied acrylic grouts. Mix Part A (orange or blue) with 2% accelerator and then mix with Part B (colourless) in a 1:1 volume ratio. Apply as per manufacturer’s TDS 'V1UK20 – 2020.10.22'. Cure for 12 hours at 16°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'TamPur 150'. Site applied, Hydrophilic polyurethane foam which is an amber coloured liquid when unreacted and a pale yellow coloured, flexible foam material when cured. Mix TamPur 150 with water in a volumetric ratio of 1:1 and apply as per manufacturer’s TDS 'V1UK19 – 2019.4.25'. Cure for 24 hours at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of bottom entry BS1212-4 telescopic fill valves with plastic bodies. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim check valve cartridge with stainless steel spring and EPDM `O`-ring. For insertion into specifically dimensioned bores. Maximum working pressure 16 Bar. BS6920 at 85°C
Range of tundishes incorporating a black or grey plastic body or mild steel painted black body (128-2001 CST, 128-2003 CST, 128-2004 CST & 128-2005 CST models only). Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies, incorporating silicon and NBR‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of ceramic cartridge headworks with plastic bodies & silicone rubber seals. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
Thermostatic cartridges with plastic or brass bodies, and EPDM ‘O’ rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. BS6920 85°C.
‘VT30’ range of thermostatic cartridges with a plastic body and EPDM ‘O’-rings and stainless steel strainers. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. BS6920 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet is a waterfall type. Maximum working pressure 5.0 bar. Maximum operating temperature 85ºC.
Range of single hole, single outlet (fixed) combination tap assemblies ( brass bodies - various finishes), incorporating either a ceramic cartridge or ceramic disc (see models) headworks with either a single lever or cross top (see models) operating member. The spout outlet incorporates either a plastic aerator, a plastic flow straightener or an open outlet type spout (see models). Some models are supplied with a click type waste and some are supplied with a lever type pop-up waste (see models). Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Range of single hole, single outlet (fixed) combination tap assemblies incorporating a brass body and ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 90.0°C
Range of overhead shower outlets, (chrome plated ABS bodies). The inlets incorporate a plastic flow regulator. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating ceramic disc headworks with single lever operating members (see models). The inlets incorporate stainless steel strainers. The spout outlets incorporate a plastic aerator or a flow straightener. Maximum working pressure 10 Bar. Maximum operating temperature 65 °C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 3.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Single-hole, single outlet (swivel) combination tap assembly, (stainless steel body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 49 of 82
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
